summary manual to form a network

7/30/2019 Summary Manual to Form a Network

1/10

Below are the steps of how to form the network for a Suitcase with the following devices (Two Gang

switch, One Gang switch, curtain switch, and a socket switch):

- Firstly, you have to start by changing the Password, SSID, and the Authentication Type:1- Connect the Mastermind to the modem and the modem to the computer. (Dont forget to turn

off your computer Wireless before you start).


2/10

2- Key in the default IP Address (192.168.1.1) Using your internet browser; then you need to key inthe Username and the password (username and password are the same which is admin by

default).

TP-Links m homepage is supposed to pop up.


3/10

3- Click on Interface Setup which has three tabs below it; click on Wireless, then scroll down till youfind the SSID, Authentication Type, and Pre-Shared Key, enter a new name for the SSID after

that change the Authentication type to WPA2-PSK. Eventually, Key in the new password which is

domosetup.

(Warning do not forget to click on the save button, you can find it at the bottom of the page).


4/10

- Before forming the network you have to join each device to the network individually; youshould connect the mastermind (P4) to the Power switch (COMM).

- You can start the SetupV2 using Start Blue Stacks. Before you can start forming, you always shouldcheck the Configure Login to reconnect:


5/10

1- The Public IP, the local IP, the Port, the Username and the password are supposed to be thesame as the ones in the picture below:

-Note that the password is admin123456, if the Mastermind is being used for the first time you

have to reset the username and the password before you save or reconnect:

-Press SW2 for five-to-six seconds (D4 is supposed to turn on).

-After that press (Change Username/Password)


6/10

2- After that is being done successfully, you should click on Form Network (you can find it in theprograms main page) then you can start forming the network. When you click Form Network

the question in the following picture will pop up:

If you did not configure this

device before you have to press

no and then you have to Init the

Mastermind RF. If you did

configure it before then just

click yes. (Warning: dont Init

the Mastermind unless you are

sure as Init will remove

everything that has been saved

on the mastermind before.)

Now you can start forming the network, which is done in few steps:

1- Connect the device to the mastermind , press Get Info


7/10

2- After that click on Add Device; This process will take Twenty to forty seconds; meanwhile theswitch led will be blinking. (Note that you must wait until the Led stop Blinking at all.)

-By right when the led stop blinking, the new device has already been added to the table.

3- Double-click on the new device; you should test and Rename the location and the name for eachdevice according to its location in the real site.

- The first switch in this suitcase is a two gang switch, so when you click on Add device, on thesoftware table you are supposed to get the same EUI as the one PCB itself.

-


8/10

- Note that you have to do the same process for each Device meant to be in the network. Thesecond device, it is a one Gang switch. After the device has been added to table successfully the

EUI in the table and on the PCP are supposed to be the same.

- For the next device which is a curtain, you also have to check if the EUI is the same:


9/10

The last switch is a socket, double check the EUI after it has been added successfully.

- You have to upload the table to the Mastermind; go to the main page of the program click onConfigure table then click on Upload Table.


10/10

- Last but not least, Make sure that the table has been uploaded; by deleting the current table (Clear

Table) and click Download Table by (to download the table you just uploaded to the mastermind and

compare, by right, you should get back the same table.

summary manual to form a network

Documents