t front leg rear leg right arm left arm canopy · 2016. 2. 26. · front leg rear leg leg crossbar...
TRANSCRIPT
1
Parts Quantity
2
Q
TFront legRear leg
Leg crossbar
Right back crossbar Left back crossbar
Right arm Left arm
seat support Seat assembly
Canopy edge bar Canopy side bar
Seat cushion Canopy
Arm cushion
long barshort bar
4
AA M6 x 36L bolt 1
BB M6 x 65L bolt 4
CC M8 x 30L bolt 8+1
DD M8 x 65L bolt 4
EE M8 x 75L bolt 2
FF M6 nut 3
GG M8 nut 6
HH M6 metal washer 3
II M8 metal washer 18+2 spare
JJ plastic washer 2
KK steel plate 2
LL 2
MM black knob 2
NN M6 bolt cap 5
OO M8 bolt cap 14+1 spare
PP M6 nut cap 3
QQ M8 nut cap 6
3
spare
double S-hook
1) Align the two Top Frame Bars (A). Place one of the Steel Plates (KK) on top of the joint of the Frame Bars (A). Align the two holes in the Top Frame Bars with the two holes in the steel plate. Insert two M6 x 65L Bolts (BB) through the upper steel plate and through the Top Frame Bars. Align the two holes of the lower steel plate with the bottom of the Top Frame Bar (A) and continue the bolt through this plate and an M6 Nut (FF). Don’t tighten completely. See Fig. 1.
2) Align the two holes at one end of Top Frame Bar with the two holes in the top of the Front Leg (B) and the two holes in the top of the Rear Leg (C) on the other side. Insert an M8 x 65L Bolt (DD) through an M8 Metal Washer (II), through Front Leg (B), Top Frame (A), Back Leg (C), through another Washer (II) and into an M8 Nut (GG) for each hole. Don’t completely tighten. See Fig. 2. Repeat procedure on the other side of the frame.
3) Adjust the angle of the two legs. Place a Leg Crossbar (D) between two legs on one end of the frame, lining up the bolt holes. For each hole in the front and back legs, insert an M8 x 30L Bolt (CC) through an M8 washer (II), through the leg and into the leg crossbar. Don’t completely tighten. See Fig. 3. Repeat procedure for the crossbar between the other legs.
M6 x 65L bolt
M8 x 30L bolt
M8 x 65L bolt
M6 nut
M8 nut
M8 metal washer
Steel plate
M6 bolt cap
M8 bolt cap
M6 nut cap
M8 nut cap
BB
CC
DD
FF
GG
II
KK
NN
OO
PP
2
8
4
2
4
16
2
2
12
2
4
Fig. 1
Fig. 2
Fig. 3
Frame Assembly
4
open nut
damaging
2
2
2
2
4) Join the Right and Left Back Crossbars (F, E) in the center and insert an M6 x 36L Bolt (AA) through the two Back Crossbars (F, E), through an M6 Washer (HH) and an M6 nut (FF). Do not completely tighten. See Fig. 4. Align the assembled back crossbar with the hole in the lower back legs. For each hole insert an M6 x 65L Bolt (BB) through an M6 washer (HH), through the Back Leg and into the Back Crossbar. Do not tighten completely. See Fig. 5.
5) Now go back and securely tighten all nuts and bolts. Place Bolt Caps (NN, OO) over all Bolts, and place Nut Caps (PP, QQ) over all Nuts.
6) Lay out the Right Seat Arm (G), Left Seat Arm (H), Seat Supports (I). Make sure that the labels marked “Front’’ on the arms are all facing the front edge of the seat. Connect the arms to the seat supports by sliding the tabs on the ends of the seat supports down into the brackets on the arms. Make sure they are securely seated. See Fig. 6.
7) Open the Seat Assembly (J) and lay it on top of the frame from Step 6, lining up the holes in the Seat Arms (G, H) with the holes in the side tubes of the Seat Assembly (J). Insert an M8 x 75L Bolt (EE) from outside through the arm holes, through a Plastic Washer (JJ), through the side bar on the Seat Assembly, through an M8 Washer (II) and an M8 Nut (GG). Don’t tighten completely. See Fig. 7. Repeat procedure on the other side. Then securely tighten the Bolts and Nuts and cover with Caps (OO,QQ).
Fig. 7
Fig. 6
Fig. 4
Fig. 5
Seat Assembly
5
M8 x75L bolt
M8 nutM8 metal washer
Plastic washer
M8 bolt cap
M8 nut cap
EE
GGII
JJ
OO
QQ 2
2
M6 nut
M6 metal washerM6 bolt cap
M6 nut cap
M6 x 65L boltM6 x 36L boltAA
BB
FF
HH
NN
PP
1
2
1
3
3
1
Fig. 10
Fig. 9
Fig. 8
8)
9)
6
(Q)
Position two Long Bars (L) so that the end marked "TOP" is upside. Hang the Double S-Hook (LL) through the top holes of long bars. Slide two pins on the outside of an arm through the bottom holes of two long bars . See Fig. 9. Position a Short Bar (K) so that the end marked "TOP" is upside. Hang the double S-Hook (LL) through the top hole of short bar. Drag out of the bracket of the short bar, and slide a pin outside of the Seat Assembly (J) through the Short Bar (K). Repeat the procedure for the other side. See Fig. 10. Then hang the whole assembley seat on the top frames. See Fig. 11.
See Fig. 8.
Fig. 11
MM Black knob 2
Fig. 14
Fig. 13
Fig. 12
12
13
14.
10)
11)
12)
M
P
N
7
(M)
.
Converting the swing to a hanging bed
Fig. 16
Fig. 15
13)
ONE-YEAR LIMITED WARRANTY
8
To convert the swing into a hanging bed, lift the brackets of the Short Bars (K), pull the pins out from the short bars. Fasten the back support of the seat assembly to the U-shape bracket of the Back Crossbars (E, F). When used as a bed, the seat assembly should be secured by these holders and not allowed to swing. See Fig .15 and 16.