technical data booklet

Table of ContentsR/A Soap � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2Release Agent � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3Liquid Release � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4Set Retarder SR-PA � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5Color Hardener � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6Integral Color � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7Blended Color � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8Primary Color � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9Patina Stain � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10Neutralizer � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11Acid Wash � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12Acid Free Patina Stain � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13Water Based Dye � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 14Solvent Based Dye � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15PRECISION GROUT � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 16Flex Cement � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 17Flex Cement � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18Face Mix � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 19EPOTECH � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20EPOTECH � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 21Fast Patch � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22H-Patch � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 23Broom Coat , Grey and White � � � � � � � � � � � � � � � � � � � � � � � � � � � � 24Grey/White Stamp � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 25Self Level Overlay (SLO) � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 26Self Level Overlay (SLO) � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 27Lightweight Concrete � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 28Ultrabond Topping Polymer � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 29Ultrabond Topping Primer � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 30Ultrabond Topping Polymer L3 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 31Silane-Q HD � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 32CS Series Sealers � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 35Acrylithin � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 36AquaShed Penetrating Sealer � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 37Cure & Seal – Water Base � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 38Acrylic Waterbase Sealer � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39PA - 30 VOC 400 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 40DecaThane 200 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 41DecaThane 200 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 42DecaThane 230 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 43DecaThane 230 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 44DecaThane 250 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 45DecaThane 450 VOC400 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 46DecaThane 450 VOC400 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 47Ultrabond 400 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 48Ultrabond 680 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 49Ultrabond 680 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 50Ultrabond 803 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 51WB Cure � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 52WBW Cure � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 53

USESRemoves Release Agent off of mats and driveway. Can be used to clean concrete counter tops. Also removes grease.

PACKAGINGR/A Soap is available in 3.78 L. / 1 Gal. containers.

LIMITATIONSR/A Soap is a cleaner, NOT a sealer or coating.

INSTALLATION INSTRUCTIONSCleaning: dilute with 5-10 parts of water. Rinse or wipe clean equipment. Surfaces subjected to direct food contact must be thoroughly rinsed with potable water after cleaning with this product. Avoid contamination of food during use. Do not store in food processing or food storage area.

PROPERTIESAppearance clear liquidOdor light citrusSpecific Gravity 1.06 g/cm³PH 13.0

TECHNICAL SERVICESComplete technical information is available from Concretech Inc. and its authorized applicators and distributors. In house laboratory testing is available for specialty applications. Technical services available in North America call toll free 1.888.503.6780

R/A Soap

PRODUCT DESCRIPTIONR/A Soap is a penetrating cleaning agent. R/A Soap is a biodegradable, ecologically safe, non-flammable and contains no ammonia or other volatile components. R/A Soap cleans immediately to suspend, emulsify and float grease, wax, gum, dirt and oil. It cleans without leaving deposits.

104, 2567 192 StreetSurrey, BC V3S 3X1

www.concretechproducts.com

Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

Concretech Inc.’s sole warranty is that our products have been manufactured to meet with our written specifications. The information herein is general information to assist our customers in deter-mining whether our products are suitable for their applications. Our products are intended for sale to commercial and industrial customers. We require customers to inspect and test our products before use and to satisfy themselves as to contents, suitability and applications. Nothing herein shall constitute any other warranty, express or implied, including any warranty of merchantability or fitness for a particular purpose, nor is any protection from any law or patent inferred. All patent and trademark rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for incidental or consequential damages.

USESFor use on all interior and exterior stamped concrete, imprinted horizontal and vertical surfaces.

PACKAGINGConcretech Release Agent is available in 25 standard colors and an unlimited range of custom colors. Concretech Release Agent is packaged in 30 lb. (13.63 Kg.) pails and coverage is approximately 800 square feet per pail.

LIMITATIONSProtect all surfaces that are not intended to receive Release Agent. Take caution when using during windy conditions or where rapid air movement exists. Use a commercial grade detergent to facilitate the removal in unwanted areas. Never leave excess residue of Release Agent on a substrate that is to be covered with concrete or other surface finishes.

INSTALLATION INSTRUCTIONSUpon completing final troweling of integral colored or color hardenedconcrete, apply a light even coat of Concretech Release Agent over the area to be imprinted. Allow bleed water to dissipate before broadcasting Release Agent on surface. Release Agent shall be applied in one or more broadcasts. Use “hand broadcast” method applying evenly and consistently. It is generally recommended that the Release Agent be a complimentary contrasting color, usually darker than the concrete. Recommended application rate is 30 lbs. per 800 square feet. Never trowel Release Agent into the surface, as this will cause discoloration and reduce concrete strength. Do not add water to surface while imprinting over Release Agent. In some instances Release Agent may be used in conjunction with Liquid Release. Contractors should test this method and perfect their techniques before attempting installation.

Cleaning:Once concrete has set, remove excess Release Agent with soft bristle broom or vacuum or in some instances hose off with clean water. Take care not to damage the surface before concrete has reached final set. After the concrete has reached initial cure, wash the surface, scrubbingwith broom and commercial degreaser. Surface is sufficiently clean when water on the surface no longer beads. In general it is desirable to leave release color representing 10% to 30% of the final color. Finishing: All colored and imprinted concrete surfaces shall have a sealer or water repellent coating applied to protect the finish from moisture and oxidization. Apply Concretech Cure and Seal (CS-15) as soon as possible. Follow up with Concretech High Solids Sealer (CS-25 or CS- 30) after 28 days. Follow Concretech technical bulletins for applied product.

PROPERTIESAvailable in 25 standard colors. Coverage is approximately 800 SqFt. per pail. Custom colors available upon request. TECHNICAL SERVICESComplete technical information is available from Concretech Inc. and its authorized applicators and distributors. In house laboratory testing is available for specialty applications. Technical services available in North America call toll free 1.888.503.6780

Release Agent

PRODUCT DESCRIPTIONConcretech Release Agent is a dry shake material formulated to facilitate the use and release of stamp tools for imprinting during the plastic set stage of concrete. Concretech Release Agent is blended, UV stable, high quality synthetic pigments, micronized aggregates, hydrophobic materials and admixtures providing easy release of imprint tools and rich accent colors. Concretech Release Agent increases imprint tool life and reduces imprinting labor. Concretech Release Agents are available in 30 lb. pails and in a wide assortment of colors.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use on all interior and exterior stamped concrete.

PACKAGINGLiquid Release is available in 3.78 L. / 1 Gal. and 18.9 L. / 5 Gal. containers.

LIMITATIONSDo not apply when rain or inclement whether is anticipated in the first 12 hours after application. Equipment Contractors must use a sprayer designed for use with solvents. Other equipment may explode or fail resulting in harm to persons or surrounding surfaces.

INSTALLATION INSTRUCTIONSApply Concretech liquid release liberally to concrete surface and imprint tools with pump up airless sprayer. Do not apply to areas greater than 15 to 20 sq. ft. at a time as liquid evaporates rapidly.Immediately imprint area where liquid release is applied. Re-apply to areas that have lost sheen. Do not work liquid release into concrete surface. Make any necessary corrections to surface texture by pressing out with imprint tool. Coverage is 800 to 1200 sq. ft. per 5- gallon pail, depending on surface porosity and surface texture. Be cautious when using on polymer-modified overlays – applying too early in plastic stage set may result in minor cracking. Clean all stamp mats and imprint tools with soap and water after use.

FinishingAll colored and imprinted concrete surfaces shall have a sealer or water repellant coating applied to protect the finish from moisture

and oxidization. Apply Concretech cure and seal (CS 15) as soon as possible. Follow up with Concretech high solids sealer (CS 25 or CS 30) after 28 days.

STORAGEContractor shall abide by all regulatory agencies regulations for application, use, storage and disposal of solvent based materials.

PROPERTIESColor……………………….ClearDry time………….5 to 30 minutesCoverage is 800 to 1200 SqFt. per 18.9 L. (5 Gal.) pail.(Depending on surface porosity.)

SAFETY PRECAUTIONSCaution Flammable!Use only in well ventilated areas. Prevent contact with all sources of ignition, heat, spark and electric tools. Wear respirator for use with solvents. Wear protective clothing, rubber gloves and eye protection. Prolonged exposure may result in respiratory illness, dizziness or nervous system damage. Keep out of reach of children.

TECHNICAL SERVICESComplete technical information is available from Concretech Inc. and its authorized applicators and distributors. In house laboratory testing is available for specialty applications. Technical services available in North America call toll free 1.888.503.6780.

Liquid Release

PRODUCT DESCRIPTIONLiquid Release is a synthetic blended, clear releasing agent used as a parting agent for imprinting tools on stamped concrete. Liquid release reduces friction providing longer life to all imprint tools. Concretech liquid release produces finishes that are different in character than Concretech release powders. The use of liquid release will increase applicator speed and does away with clean up and surface preparation prior to sealing. Liquid release is ideal for use in areas where cleaning traditional release powders is a challenge. No removal of liquid release is required prior to coloration and sealing. Test compatibility with imprint tools before using.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESSet Retarder SR-PA is used on vertical and horizontal surfaces. For horizontal surfaces, Set Retarder SR-PA can be applied directly to freshly poured and trowelled concrete. For vertical surfaces, Set Retarder can be applied to forming materials made of wood, steel or plastic.

PACKAGINGSet Retarder SR-PA is available in One Gallon and Five Gallon plastic containers.

LIMITATIONSRetarding time may vary with temperature, humidity and concrete matrix. Concrete accelerators will inhibit the retarding. 10-20% by volume water may be added to decrease the retarding action for horizontal surfaces. Set Retarder SR-PA is more effective when water is added. Do not apply retarder when rain is anticipated within 12 hours of application, and when temperature is below 0 ºC (32ºF) and above 25 ºC (77ºF). For both horizontal and vertical applications, always conduct a test. Compressive strength prior to water flushing should be between 1,000 and 1,500 psi (6.89 and 10.34 MPa). Using Set Retader SR-PA will not prevent the ultimate hardening of concrete, but will only delay the set time.

INSTALLATION INSTRUCTIONSFor horizontal surfaces, place the concrete first; stir and apply Set Retarder SR-PA just after the surface water disappears. Set Retarder SR-PA can be brushed, rolled or sprayed with low-pressure sprayer. Protect the surface from wind, rain or overhead sun. Start to wash the surface after 12 to 24 hours when the concrete is hard enough. If the retarded depth is excessive let the concrete cure for several more hours. Retardation time is subject to many variables. Check the set retarder at different time intervals to satisfy the personal preference.

Wash the surface with water broom or a stiff broom and hose. Do not leave material on the surface. For vertical concrete surfaces, do not dilute Set Retarder SR-PA. Stir and then spray Set Retarder SR-PA to vertical surface of the forms and allow to dry before concrete is poured into the forms. For porous and absorbent surfaces like plywood, a coat of diesel oil can be applied first then let it dry to stop the retarder from penetrating. It usually takes 20 minutes to dry, but it may vary depending on the weather conditions. When the concrete has set, open the forms and hose off the surface to remove retarded surface material to reveal the exposed aggregate. Apply Concretech Acrylic Sealer CS-15 Cure & Seal to the exposed surface. Where a wet look surface is desired, apply Concretech Acrylic Sealer CS-25 28 days after placement. See Concretech Acrylic Sealers for more information. Proper pumping or suitable absorbent material can collect spills. For additional information regarding handling and disposal, please refer to MSDS of this product. Keep the product from freezing. It should be stored at temperatures between 5ºC – 20 ºC.

PROPERTIESAs SuppliedAppearance Green Clear LiquidOdor Alcoholic OdorPH 10.5Specific Gravity 1.005 g/cm3Application Rate 100-200 sq. ft. / gal


Set Retarder SR-PA

PRODUCT DESCRIPTIONSet Retarder SR-PA is a fast drying concrete surface retarder that effectively delays the set time of both vertical and horizontal concrete surfaces. It is applied to freshly placed concrete to retard hydration reaction of surface cement of approximately 1/4 “ thickness for up to 24 hours to create an exposed aggregate surface. Set Retarder SR-PA has no effect to the color or sheen.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use on all interior and exterior concrete, stamped concrete, coloredand flat work concrete.

PACKAGINGConcretech Color Hardeners are packaged in 27.27 kg (60lbs) pails and 22.7 kg (50lbs) bags. 25 standard colors. Custom colors available upon request.

LIMITATIONSDo not apply when temperature is below 4°C (38°F) or above 43°C (110°F). Take caution when using during windy conditions or where rapid air movement exists. Do not apply when rain or inclement whether is anticipated in the first 24 hours after application. Surface must be dry before applying any sealer.

INSTALLATION INSTRUCTIONSPlace at least 4” depth concrete of a mix design suitable for stamped concrete not to exceed a 5” slump. Screed in two directions providing a consistent and uniform surface. Allow bleed water to dissipate before broadcasting Color Hardener on surface. Color Hardener shall be applied in two broadcasts. Use “hand broadcast” method applying evenly and consistently. On the first broadcast apply 75% of specified amount and bull float in. On the second broadcast apply the remaining 25% of specified amount and bull float, fresno or trowel in to uniform and even finish. Recommended application rate is 27.27KG (60lbs) per 100 sq ft. Troweling to prevent discoloration and color inconsistency. Do not add water to surface while troweling in Color Hardener. Do not use admixtures containing chloride with Color Hardener. Color Hardener may be mixed with Polytop liquid for use on vertical surfaces such as stair risers. All color hardened concrete surfaces shall have a

sealer or water repellent coating applied to protect the finish from moisture and oxidization. Apply Concretech cure and seal (CS 15) as soon as possible. Follow up with Concretech high solids sealer (CS 25 or CS 30) after 28 days. Follow Concretech technical bulletins for the applied product.

STORAGE AND HANDLINGStore in cool dry area out of direct sunlight. Shelf life under normal conditions is one year. Store in sealed containers. Color Hardener that has been exposed to moisture for prolonged periods should be discarded.

PROPERTIESColors 25 Standard Colors plus custom colors availableCure time 12 Hours @ 21°C (70°F)

SAFETY PRECAUTIONSCaution - Contains Portland cement. Wear protective clothing, rubber gloves, eye protection and dust respirator mask. Prolonged exposure may result in respiratory illness. Keep away from children.

First Aid - Flush contaminated areas immediately and seek medical attention. Remove contaminated clothing. Wash hands with soap and water. Flush eyes with clean water or eye wash solution. In all cases seek immediate medical attention.


Color Hardener

PRODUCT DESCRIPTIONConcretech Color Hardener is a dry shake material formulated to color “poured in place” concrete. Color Hardener is designed for architectural flat work and stamped concrete surfaces. Concretech Color Hardeners are blended, UV stable, high quality synthetic pigments, portland cements, hard surface aggregates and admixtures, providing permanent long wearing surfaces for vehicle and foot traffic. Concretech Color Hardeners increase abrasion resistance, increase surface strengths and reduce scaling. Concretech Color Hardener is available in 27.27KG (60lbs) pails and 22.7 kg. (50lbs.) bags



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


COMPLIANCEComplies with ASTM C-979. They are light fast, durable, weather resistant and long lasting in concrete.

USESFor use on all interior and exterior concrete, stamped concrete, coloredand flat work concrete as well as any typical area where concrete or decorative color is used.

PACKAGINGConcretech synthetic iron oxide pigments are available in 6.5 lb, 25 lb and 55 lb. disintegrating bags. Available in 11 base colors, 25 blended colors and color match to synthetic concrete compatible colors upon request.

LIMITATIONSDo not use color with mixes that contain chloride admixtures. Maintainslump of less than 5”. Use the same pigment to cement ratio throughout. Use same brand, type and ratios of cement, aggregates and admixtures throughout project. Refer to Concretech Architectural Specifications for installation procedures, base preparation, forming and product information. Do not cure with plastic sheets, water or curing agents that may discolor the surface. Do not leave wood or other products on the surface while curing, as this will cause discoloration.

INSTALLATION INSTRUCTIONSConfirm color, weight, mix-ratio and weight of bag or combination of bags prior to starting. Specify air content and maintain throughout job.Wet mixer with 2/3 mix water and toss in Concretech disintegrating bag(s) then add remaining ingredients and mix water, mixing at charging speed, for at least 5 minutes. Schedule loads for consistent mix times. Place at least 4” depth concrete of a mix suitable for design use (i.e. stamped concrete) not to exceed a 5” slump. Screed in two

directions providing a consistent and uniform surface. Allow bleed water to dissipate before final troweling. Late or hard troweling may cause “burns” or dark spots. Keep troweling to a minimum to prevent discoloration and color inconsistency. Do not add water to surface or tools while troweling or finishing as this may cause light spots of color and reduce surface strength. All colored concrete surfaces shall have a sealer or water repellant coating applied to protect the finish from moisture and oxidization. Apply Concretech Cure and Seal (CS 15) as soon as possible. Follow up with Concretech High Solids Sealer (CS 25 or CS 30) after 28 days. Follow Concretech Technical Bulletins for the applied product.

PROPERTIESAs SuppliedBase colors 11 standard colorsColors 25 blended colorsCustom colors available

SAFETY PRECAUTIONSCaution - Wear protective clothing, rubber gloves, eye protection and dust respirator mask. Prolonged exposure may result in respiratory illness. Keep away from children.

First Aid -Flush contaminated areas immediately. Remove contaminated clothing. Wash hands with soap and water. Flush eyes with clean water or eye wash solution. In all cases seek immediate medical attention.


Integral Color

PRODUCT DESCRIPTIONConcretech Synthetic Iron Oxide Pigments are high quality synthetic iron oxide pigments for use in cast in place, slab on grade, tilt up, pavers, masonry, mortar, stamped concrete, shotcrete or any place color in concrete is used. Concretech synthetic iron oxide pigments are available in a wide array of primary colors and can be custom matched to meet design requirements.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147



USESFor use on all interior and exterior concrete, stamped concrete, colored and flat work concrete as well as any typical area where concrete or decorative color is used.

PACKAGINGConcretech synthetic iron oxide pigments are available in 6.5 lb, 25 lb, and 50 lb. disintegrating bags. Available in 11 base colors, 12 blended colors and can be custom blended on request.

LIMITATIONSDo not use color with mixes that contain chloride admixtures. Maintain slump of less than 5”. Use the same pigment to cement ratio throughout. Use same brand, type and ratios of cement, aggregates and admixtures throughout project. Refer to Concretech Architectural Specifications for installation procedures, base preparation, forming and product information. Do not cure with plastic sheets, water or curing agents that may discolor the surface. Do not leave wood or other products on the surface while curing, as this will cause discoloration.

INSTALLATION INSTRUCTIONSConfirm color, weight, mix-ratio and weight of bag or combination of bags prior to starting. Specify air content and maintain throughout job. Wet mixer with 2/3 mix water and toss in Concretech disintegrating bag(s) then add remaining ingredients and mix water, mixing at charging speed, for at least 5 minutes. Schedule loads for consistent mix times. Place at least 4” depth concrete of a mix suitable for design use not to exceed a 5” slump. Screed in two directions providing a consistent and uniform surface. Allow bleed water to dissipate before final troweling. Late or hard troweling may cause “burns” or dark spots. Keep troweling to a minimum to prevent discoloration and color inconsistency. Do

not add water to surface or tools while troweling or finishing as this may cause light spots of color and reduce surface strength. All colored concrete surfaces shall have a sealer or water repellant coating applied to protect the finish from moisture and oxidization. Apply Concretech Cure and Seal (CS 15) as soon as possible. Follow up with Concretech High Solids Sealer (CS 25 or CS 30) after 28 days. Follow Concretech Technical Bulletins for the applied product.

STORAGE AND HANDLINGStore in cool dry area out of direct sunlight. Shelf life under normal conditions is one year. Store in sealed containers. Pigment that has been exposed to moisture for prolonged periods should be discarded.

PROPERTIESBase Colors 11Standard Colors 12Custom colors available

SAFETY PRECAUTIONS

Caution - Wear protective clothing, rubber gloves, eye protection and dust respirator mask. Prolonged exposure may result in respiratory illness. Keep away from children.



Blended Color

PRODUCT DESCRIPTIONConcretech Blended Colors are high quality synthetic blended iron oxide pigments for use in cast in place, slab on grade, tilt up, pavers, masonry, mortar, stamped concrete, shotcrete or any place color in concrete is used. Concretech Blended Color pigments are available in a wide array of standard colors and can be custom matched to meet design requirements.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use on all interior and exterior concrete, stamped concrete, coloredand flat work concrete as well as any typical area where concrete or decorative color is used.

PACKAGINGConcretech synthetic iron oxide pigments are available in 7 lb, and 25 lb disintegrating bags. Available in 11 base colors, 25 blended colors and color match to synthetic concrete compatible colors upon request.

LIMITATIONSDo not use color with mixes that contain chloride admixtures. Maintainslump of less than 5. Use the same pigment to cement ratio throughout. Use same brand, type and ratios of cement, aggregates and admixtures throughout project. Refer to Concretech Architectural Specifications for installation procedures, base preparation, forming and product information. Do not cure with plastic sheets, water or curing agents that may discolor the surface. Do not leave wood or other products on the surface while curing, as this will cause discoloration.

INSTALLATION INSTRUCTIONSConfirm color, weight, mix-ratio and weight of bag or combination of bags prior to starting. Specify air content and maintain throughout job.Wet mixer with 2/3 mix water and toss in Concretech disintegrating bag(s) then add remaining ingredients and mix water, mixing at charging speed, for at least 5 minutes. Schedule loads for consistent mix times. Place at least 4 depth concrete of a mix suitable for design use (i.e. stamped concrete) not to exceed a 5 slump. Screed in two directions providing a consistent and uniform surface. Allow bleed water to dissipate before final troweling. Late or hard troweling may cause “burns” or dark spots. Keep troweling to a minimum to prevent

discoloration and color inconsistency. Do not add water to surface or tools while troweling or finishing as this may cause light spots of color and reduce surface strength. All colored concrete surfaces shall have a sealer or water repellant coating applied to protect the finish from moisture and oxidization. Apply Concretech Cure and Seal (CS 15) as soon as possible. Follow up with Concretech High Solids Sealer (CS 25 or CS 30) after 28 days. Follow Concretech Technical Bulletins for the applied product.

PROPERTIESAs SuppliedBase colors 11 standard colorsColors 25 blended colorsCustom colors available




Primary Color

PRODUCT DESCRIPTIONConcretech Synthetic Iron Oxide Pigments are high quality synthetic blended iron oxide pigments for use in cast in place, slab on grade, tilt up, pavers, masonry, mortar, stamped concrete, shotcrete or any place color in concrete is used. Concretech synthetic iron oxide pigments are available in a wide array of standard colors and can be custom matched to meet design requirements.




Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

Concretech Inc.’s sole warranty is that our products have been manufactured to meet with our written specifications. The information herein is general information to assist our customers in deter-mining whether our products are suitable for their applications. Our products are intended for sale to commercial and industrial customers. We require customers to inspect and test our products before use and to satisfy themselves as to contents, suitability and applications. Nothing herein shall constitute any other warranty, express or implied, including any warranty of merchantability or fitness for a particular purpose, nor is any protection from any law or patent inferred. All patent and trademark rights are reserved. The exclusive remedy for all proven claims is placement of our materials and in no event shall we be liable for incidental or consequential damages.

USESFor use on all interior and exterior stamped concrete, flat work, hard steel troweled concrete and vertical surfaces.

PACKAGINGConcretech patina acid stains are available in eleven colors. Patina acid stain is packaged in 1 gallon containers.

LIMITATIONSInspect all surfaces to ensure that they are sound, free of chloride admixtures and is free of contaminants. Existing concrete should be at least 28 days old or in the case of polymer modified topping at least 7 days old. Surface preparation and cleaning is the most important aspect in obtaining desirable results. Do not acid wash prior to application. Remove loose material, scaling and oxidized particles from surface. Existing concrete surfaces should be scrubbed with a commercial degreaser using a red or black buffer pad on a commercial floor maintainer. Thoroughly flush all residues from cleaning process and sand the surface with 100 – 150 mesh sand paper on floor maintainer. Remove all dust residues from sanding process by washing with clean water at least twice. Surfaces that have cured differently or inconsistently will result in varying shades when patina is applied. Color may vary due to temperature, concrete age, conditions while curing, profile, finishing techniques and contaminates.

INSTALLATION INSTRUCTIONSComplete a test panel on site for color approval prior to stain application. Apply patina with an airless pump up sprayer. Use extra care to ensure that the sprayer is all plastic and that there are no metal parts that can come in contact with the patina as this will start the chemical reaction and will result in weak or changed color. Apply patina lightly in 3 wide bands and scrub in directly behind spraying operation. Scrubbing will evenly spread the patina over the surface and care should be taken not to leave excess patina at edges or joint lines. Follow up immediately with second light coat over scrubbed area. Leave no puddles and always maintain a wet edge. Applicators should be consistent in their methods, application rates, dilution and techniques. Older concrete may require higher acid concentrations while newer concrete surfaces may require lower acid concentrations. For older

concrete surfaces mix one part muriatic acid with 5 parts water and use this mixture to dilute 1 to 1 or more with patina stain. For weaker color, dilute with pure water. Do not walk on wet surface. Allow the surface to dry completely before rinsing or applying more patina. Once color has developed and surface is dry it must be vigorously scrubbed to remove excess residue. Wet the surface and scrub with the red pad on floor maintainer using Concretech’s neutralizing solution. Remove scrubbed residue and rinse with clean water.

STORAGEStore in cool area out of direct sunlight. Shelf life under normal conditions is one year. Store in sealed containers, with the lid tight andin an upright position.

PROPERTIESAs SuppliedColor 11 Standard colorsPH Mildly AcidicCure Time 4-12 Hours

SAFETY PRECAUTIONSCaution Contains hydrochloric acid. Wear protective clothing, rubber gloves, eye protection and acid vapor mask.Do not breath vapors. Use in well ventilated areas. Keep away from combustibles and other reactive materials and heat sources. Corrosive liquid. Can cause severe skin burns, respiratory irritation, eye irritation or blindness. Keep away from children.

First Aid: Flush contaminated areas immediately and seek medical attention. Remove contaminated clothing. Wash hands with soap and water. Flush eyes with clean water or eye wash solution. In all cases seek immediate medical attention.


Patina Stain

PRODUCT DESCRIPTIONPatina Acid Stain is a mildly acidic solution produced in eleven base colors. When they are applied to a substrate containing cement and calcium they react to produce an oxidized earth tone color in the concrete. Patina acid stain produces natural and variegated colors commonly found in slate, rock and other natural materials. Patina acid stain is not a coating and does not cover discoloration, stains or imperfections. The concrete character is highlighted producing the look of authentic, natural elements of nature. Colors produced from each of the eleven available colors are unique to each surface and vary widely over the area stained. These variegations, variances and color shifts are both natural and desirable in this coloration system.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use on all concrete surfaces, interior and exterior stamped concrete, imprinted horizontal and vertical surfaces.

PACKAGINGNeutralizer is available in 3.78 L. / 1 Gal. and 18.9 L. / 5 Gal. Containers

INSTALLATION INSTRUCTIONSAfter 4 - 24 hours drying time (depending on desired color richness) for Patina Stain, all residue must be completely removed and stained concrete must be neutralized. The residue can be removed by wet scrubbing with a suitable, high-quality commercial detergent using a rotary floor machine or a stiff bristle brush. The surface must be thoroughly rinsed after scrubbing until the rinse water is completely clean. Failure to completely remove all residues prior to sealing the surface will cause adhesion loss or peeling and reduced durability of the sealer. Apply a neutralizer evenly and consistently over the whole area. Start spraying using a low pressure pump spray at 30 to 100 psi. A fine nozzle will help ensure even distribution of the Neutralizer. Neutralizer can be scrubbed in using plastic bristle brushes and or mopped in. Use wet dry vacuum to remove liquid left on the floor or mop being careful to remove all white residue. Rinse well and leave to dry 24 hours. A pressure washer may also be used to remove any white residue that remains. Properly neutralized concrete surface will have a PH between 8-10. PH indicator Strips may be used to measure PH.

STORAGEStore in cool, dry area and away from incompatible substances. Shelf life under normal conditions is one year. Store in sealed containers, with the lid tight and in an upright position.

PROPERTIESPhysical State Water White LiquidSpecific Gravity 1.00 g/cm³Odor NoneEvaporation Rate Similar to WaterPH 8.0Solubility to Water Completely SolubleCoverage: 200 – 300 SqFt. / Gallon

SAFETY PRECAUTIONSFirst Aid: Not an eye irritant, not a skin irritant. Material is practically non-toxic. Small amounts (1-2 tablespoons full) swallowed during normal handling operations are not likely to cause injury as long as the stomach is not overly full; swallowing large amounts may cause injury. In all cases seek immediate medical attention.


Neutralizer

PRODUCT DESCRIPTIONConcretech Neutralizer is a liquid neutralizer used to neutralize any acid residue from Patina Stain and Acid Wash.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESAcid Wash is used to clean the concrete and prepare it for coating and sealing applications. Acid Wash does not react with paint, sealer, wax or grease.

PACKAGINGConcretech Acid Wash is available in:3.78 L. / 1 Gal. Plastic Containers18.90 L. / 5 Gal. Plastic Containers208 L. / 55 Gal. Plastic Drums

LIMITATIONSInspect all surfaces to ensure that they are sound, free of sealer, wax or oil. Surface preparation is the most important aspect in obtaining desirable results. Remove loose materials from the surface. Existing concrete surfaces should be scrubbed with a commercial degreaser (Concretech R/A Soap) using a red or black buffer pad on a commercial floor maintainer. Surfaces that have cured differently or inconsistently poured, will etch with different intensities. The use of Acid Wash is limited to outdoor. For indoor use, all the precautionary measurements regarding ventilation, clothing and neighboring surfaces should be taken into account. Dispose the wash-offs in accordance with federal, state, and local regulations.

INSTALLATION INSTRUCTIONSSweep the floor to remove loose soil/dirt. Remove all contaminants that are preventing the Acid Wash to reach the concrete surface, such as oil, loose particles, old paint and sealer. Pre-scrub with Concretech R/A Soap to remove heavily stuck oil or grease. Dilute one part Acid Wash with four parts of water. When working with Acid Wash always

wear proper safety rubber gloves, boots and eye goggles. Add Acid Wash to the water to avoid splashing. Apply diluted Acid Wash (4:1) to a dampened concrete surface. Never apply Acid Wash solution onto dry concrete. Acid solution reacts with concrete and starts to fizz and bubble. No fizzing is the sign of sealer or contaminants on the floor, which is preventing the Acid Wash to reach to the concrete. Scrub around with a broom to spread the acid evenly. Spray Neutralizer after the acid solution stops fizzing (about 5 min.). Rinse the excess of Neutralizer and acid with cold water pressure washer before it has a chance to dry.

STORAGE AND HANDLINGAvoid breathing vapors. Do not get in eyes, on skin or on clothing. Use recommended personal protective equipment. Wash thoroughly with soap and water after using this product and before eating, drinking or smoking. Keep containers closed. Keep out of reach of children. Store in a cool, well ventilated area away from oxidizing agents and other incompatible substances. Empty containers should be completely drained and properly disposed of.

PROPERTIESUN 1789Contact Rating 3 (Severe Corrosive)


Acid Wash

PRODUCT DESCRIPTIONAcid Wash is a powerful acidic solution with high etching and cleaning properties for concrete. Acid Wash takes one layer off the concrete surface and exposes the fresh concrete and produces a texturized surface to increase adhesion of subsequent coatings and sealers. Acid Wash can be diluted with water to produce a acid solution with different etching capabilities.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

Concretech Inc.’s sole warranty is that our products have been manufactured to meet with our written specifications. The information herein is general information to assist our customers in deter-mining whether our products are suitable for their applications. Our products are intended for sale to commercial and industrial customers. We require customers to inspect and test our products before use and to satisfy themselves as to contents, suitability and applications. Nothing herein shall constitute any other warranty, express or implied, including any warranty of merchantability or fitness for a particular purpose, nor is any protection from any law or patent inferred. All patent and trademark rights are reserved. The exclusive remedy for all proven claims is placement of our materials and in no event shall we be liable for incidental or consequential damages.

USESFor use on all interior and exterior stamped concrete, flat work, hard steel troweled concrete and vertical surfaces.

PACKAGINGAcid Free Patina Stains are packaged in 1 gallon.

AVAILABILITYAcid Free Patina Stains are available in eleven colors. Test sample kits are available upon request.

LIMITATIONSInspect all surfaces to ensure that they are sound, free of chloride admixtures and the concrete is not sealed or waxed. Existing concrete should be at least 28 days old or in the case of polymer modified topping at least 7 days old (Acid Free Patina Stain will develop varying color intensity on newly poured concrete). Surface preparation and cleaning is the most important aspect in obtaining desirable results. Do not acid wash prior to application. Remove loose material, scaling and oxidized particles from surface. Existing concrete surfaces should be scrubbed with a commercial degreaser using a red or black buffer pad on a commercial floor maintainer. Thoroughly flush all residues from cleaning process and sand the surface with 100 – 150 mesh sand paper on floor maintainer. Remove all dust residues from sanding process by washing with plain water at least twice. Surfaces that have cured differently or inconsistently will result in varying shades when patina is applied. Color may vary due to temperature, concrete age, conditions while curing, profile, finishing techniques and contaminates.

INSTALLATION INSTRUCTIONSComplete a test panel on site for color approval prior to stain application. Apply Acid Free Patina Stain with an airless pump up sprayer. Apply patina lightly in 3 wide bands and scrub in directly behind spraying operation. Scrubbing will evenly spread the patina over the surface and care should be taken not to leave excess patina at edges or joint lines. Follow up immediately with second light coat over scrubbed area. Leave no puddles and always maintain a wet edge. Applicators should be consistent in their methods, application rates,

dilution and techniques. Older concrete may require longer exposure to reach the desired color while newer concrete surfaces may require shorter exposure. If higher intensity colors are desired with older concrete surfaces mix one part muriatic acid with 5 parts water and use this mixture to dilute 1 to 1 or more with Acid Free Patina Stain. For lighter colors, dilute with pure water and use immediately.. If stored, diluted patina will dissociate and produce corrosive materials. Do not walk on wet surface. Allow the surface to dry completely before rinsing or applying more patina. Once color has developed and surface is dry it must be vigorously scrubbed to remove excess residue. Wet the surface and scrub with the red pad on floor maintainer using Concretech’s neutralizing solution. Remove scrubbed residue and rinse with clean water.

STORAGE AND HANDLINGStore in cool area approximately 20 ºC (70 ºF) out of direct sunlight. Shelf life under normal conditions is one year. Store in sealed polyethylene or PVC containers, with the lid tight and in an upright position. Wear protective clothing, rubber gloves, and eye protection.Do not breath vapors. Use in well ventilated areas. Keep away from combustibles and other reactive materials and heat sources.

First Aid: Flush contaminated areas immediately and seek medical attention. Remove contaminated clothing. Wash hands with soap and water. Flush eyes with clean water or eye wash solution. In all cases seek immediate medical attention.

PROPERTIESColor 11 standard colorsPH Mildly AcidicCure Time 4-12 Hours


Acid Free Patina Stain

PRODUCT DESCRIPTIONAcid Free Patina Stain is water-based solutions formulated with the mixture of inorganic and organic salts produced in eleven base colors. It contains no acid, very low corrosion on metal parts with mild smell and rated as only a mild irritant. When applied to a substrate containing cement and calcium they react with the bear concrete to produce an oxidized earth tone color. Acid Free Patina Stain produces natural and variegated colors commonly found in slate, rock and other natural materials. Acid Free Patina Stain is not a coating and does not cover discoloration, stains or imperfections. The concrete character is highlighted producing the look of authentic, natural elements of nature. Colors produced from each of the eleven available colors are unique to each surface and vary widely over the area stained. These variegations, variances and color shifts are both natural and desirable in this coloration system.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use on all interior structurally sound concrete surfaces where the natural appearance of concrete is desired with a shift in color tones.Applicators should perfect their technique(s) before starting installation.Mixing colors or layering the same colors create a different visual appearance. Discernment of these combinations and layers will become apparent as contractors become more familiar with the use, blending, layering and application techniques and methods. WaterBase Dyes are desirable for use with stains to shift the finish color and tones or blending problem acid stain areas.

LIMITATIONSUse at temperatures above 40ºF (5ºC) and below 95ºF (35ºC). Do not use over particleboard or gypsum based substrates. Prevent rapid air movement, rapid temperature changes or direct sunlight while applying. Avoid walking on the surface until dry and protect from contaminates until finish sealer applied. Water Base Dye must be finished with a high quality sealer for protection from abrasion and UV. Do not acid stain over previously dyed surface. Acid Stain may be used prior to using dye to create a naturally variegated surface.

INSTALLATION INSTRUCTIONSSubstrate shall be structurally sound, stable, clean, free of dust, dirt, oil, grease, paint, wax, sealers, curing compounds, laitance and drywall dust. Some surfaces may require sanding to achieve the desired finish. Water Base Dye may be diluted with plain water to provide lighter shades and tones of color and may be applied in multiple coats to achieve depth and range of color. Excess dye must be removed form the surface prior to sealing to provide maximum sealer bond to substrate. Contractors shall install an on site mock up of finished product using mixtures,

dilutions and techniques for approval by owners representative prior to installation. This mock up shall test sealer compatibility prior to installation. Keep all mixing equipment clean, mask all areas surrounding application area and prevent spillage or drips that may be very difficult to remove. Finishing: All finish concrete surfaces shall have a sealer or water repellent coating applied to protect the finish from moisture and excess abrasion. Water Base Dye may be used with acid stain. Urethane or epoxy finishes are desirable for use with dye(s).

STORAGEStore in cool, dry area out of direct sunlight. Shelf life under normal conditions is one year. Wear proper protective clothing. Keep away from children.

PROPERTIESConcretech Water Base Dye is available in four primary colors and can be mixed to achieve hundreds of colors. Water Based Dye is packaged in one gallon and five-gallon containers and for shipping purposes are not hazardous materials. Square Footage is 400 SqFt. / Gal. (Depending on usage.)


Water Based Dye

PRODUCT DESCRIPTIONConcretech Water Base Dye(s) are transparent colors formulated for indoor use on concrete surfaces and provide tones not traditionally available using Patina Stain(s). Water Base Dye will not hide surface character, defects or discoloration. Typically the results will be similar to that of Patina Stain(s) but are easier to use and provide a far greater range of color. Depth of penetration and durability are related to the strength of the concrete surface being colored, the porosity of the surface and the surface seal system used.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use on all interior structurally sound concrete surfaces where the natural appearance of concrete is desired. Applicators should perfect their techniques before starting installation. Mixing colors or layering the same colors create a different visual appearance. Discernment of these combinations and layers will become apparent as contractors become more familiar with the use, blending, layering and application techniques and methods.

PACKAGINGConcretech Solvent Base Dye is available in four primary colors and can be mixed to achieve additional colors. Solvent Based Dye is packaged in 3.78 L. / 1 Gal. and 18.9 L. / 5 Gal. pails.

LIMITATIONSUse at temperatures above 40F (5°C) and below 85°F (30°C). Do not use over particleboard or gypsum based substrates. Prevent rapid air movement, rapid temperature changes or direct sunlight while applying. Avoid walking on the surface until dry and protect from contaminates until finish sealer applied. Solvent Base Dye must be finished with a high quality sealer for protection from abrasion and UV.Do not acid stain over previously dyed surface. Acid Stain may be used prior to using dye and create a naturally variegated surface.

INSTALLATION INSTRUCTIONSSubstrate shall be structurally sound, stable, clean, free of dust, dirt, oil, grease, paint, wax, sealers, curing compounds, form release, laitance

and drywall dust. Some surfaces may require sanding to achieve the desired finish. Solvent Base Dye may be diluted with acetone to provide lighter shades and tones of color and may be applied in multiple coats to achieve depth and range of color. Excess dye must be removed form the surface prior to sealing to provide maximum sealer bond to substrate. Contractors shall install an on site mock up of finished product using mixtures, dilutions and techniques for approval by owners representative prior to installation. This mock up shall test sealer compatibility prior to installation. Keep all mixing equipment clean, mask all areas surrounding application area and prevent spillage or drips that may be very difficult to remove.

STORAGEThis product is combustible. Store in cool, dry area out of direct sunlight. Shelf life under normal conditions is one year. Wear protective clothing, rubber gloves, eye protection and respirator. Keep away from children. Use only with adequate ventilation.

PROPERTIESSquare Footage 400 SqFt. / 3.78 L. / 1 Gal.(Depending on Usage.)


Solvent Based Dye

PRODUCT DESCRIPTIONConcretech Solvent Base Dyes are transparent colors formulated for indoor use on concrete surfaces and provide tones not traditionally available using Patina Acid Stains. Solvent base dye will not hide surface character, defects or discoloration. Typically the results will be similar to that of Patina Acid Stains but are easier to use and provide a far greater range of color. Depth of penetration and durability are related to the strength of the concrete surface being colored, the porosity of the surface and the surface seal system used. Solvent Base Dyes dry fast, within a few minutes.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USES95% Effective Bearing Area (EBA) is typically achieved following proper grouting procedures. Provides placement versatility: pour, pump or dry pack.45 minute working time.Permanent support for machinery requiring precision alignment.Non-shrink from the time of placement.

PACKAGINGPrecision Grout is packaged in heavy-duty, polyethylene lined bags and is available in 50 lb. (22.7 kg) units yielding approximately 0.5 cubic feet (14.1 liters)

LIMITATIONSNever exceed the maximum water content as stated on the bag or add an amount that will cause segregation. Construction practices dictate concrete foundation should achieve its design strength before grouting.

INSTALLATION INSTRUCTIONS1. SURFACE PREPARATION: All surfaces in contact with Precision Grout shall be free of oil, grease, laitance and other contaminants. Concrete must be clean, sound and roughened to ensure a good bond. Soak concrete surfaces for 8 to 24 hours prior to application with liberal quantities of potable water, leaving the concrete saturated and free of standing water.

2. FORMWORK: Formwork shall be constructed of rigid non-absorbent materials, securely anchored, liquid-tight and strong enough to resist forces developed during grout placement. The clearance between formwork and baseplate shall be sufficient to allow for a headbox. The clearance for remaining sides shall be one to two inches (25 - 50 mm). Areas where bond is not desired must be treated with form oil, paste wax or similar material. Isolation joints may be necessary depending on pour dimensions.

3. MIXING: Mix Precision Grout thoroughly for approximately four to five minutes to a uniform consistency with a mortar mixer (stationary barrel with moving blades). A drill and paddle mixer is acceptable for single bag mixes. For optimum performance, maintain grout at ambient temperatures between 40°F and 90°F (4°C and 32°C). Use heated or chilled water to help adjust working time. Mix Precision Grout with 3-1/2 to 5-1/2 quarts per 50 lb. bag. Do not exceed maximum recommended amount of mixing water as stated on the package or add an amount that will cause segregation. Working time is approximately 45 minutes at 70°F (21°C). Follow printed instructions on the package. Always add mixing water first to mixer followed by grout.

4. PLACEMENT PROCEDURES: Precision Grout may be dry packed, poured or pumped into place. Minimum placement thickness for Precision Grout is 1 inch (25 mm). For pours over 6 inches (150 mm) in depth Precision Grout should be extended with a clean, damp coarse aggregate meeting the requirements of ASTM C 33.

5. POST-PLACEMENT PROCEDURES: Precision Grout shall be wet cured for a minimum of three days, or coated with an approved curing compound meeting the requirements of ASTM C 309 after a minimum 24 hour wet cure. In-service operation may begin immediately after the required grout strength has been reached.

STORAGEOne year in original unopened packaging when stored in dry conditions; high relative humidity will reduce shelf life.

PROPERTIESEarly Height Change, ASTM C 827 0.0 to 4.0%Hardened Height Change, ASTM C 1090 0.0 to 0.3%Effective Bearing Area 95%Bond Strength, ASTM C 882, 28 Days 2,000 psi (13.8 MPa)

Pull-out Strength, Tension, #5 threaded bar, 7 Days 2,400 psi (16.6 MPa)

Compressive Strength, ASTM C 942 (C109 Restrained) Minimum Water psi (MPa) Maximum Water psi (MPa)

1 Day 4,000 (27.6) 2,500 (17.3)3 Days 5,500 (38.0) 3,500 (24.1)7 Days 6,500 (44.9) 5,000 (34.5)28 Day 8,000 (55.2) 6,500 (44.9)Working Time at 70°F (21°C) 45 minutes


PRECISION GROUTHigh Performance Precision Non-Shrink Grout

PRODUCT DESCRIPTIONPrecision Grout is a cement-based, nonmetallic, non-shrink grout for supporting machinery and equipment. It is formulated with technology that combines high performance with the greatest reliability. When tested in accordance with ASTM C 827, Precision Grout exhibits positive expansion. Precision Grout meets the performance requirements of ASTM C 1107-02 Grades A, B and C, ASTM C 1107-07, and CRD-C 621-93 specifications for non-shrink grout over a wide temperature range, 40°F - 90°F (4°C - 32°C).



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFCW is used to water proof concrete structures in new constructions and restorations. It is suitable for waste water tanks, tunnels, concrete slabs, bridges, balconies and patios with light to medium traffic. FCW may be reinforced with Reinforcing Fabric in restoration works over the cracks to provide stronger and more durable bridging. It is approved for potable water tanks with continuous immersion.

PACKAGINGFCW is a two component material consisting of bagged, pre-mixed cement based mortar and a liquid polymer.

LIMITATIONSDo not apply to poor quality substrate. Do not use FCW when ambient temperature is less than 3oC (40oF) or more than 35oC (95oF) or when temperature is expected to fall below 2oC (36oF) during the first 48 hours after installation. Material and substrate may be conditioned to increase the temperatures to the required range. Maintain the temperature for at least 72 hours. Uncured FCW exposed to sunshine and shade will create different curing pattern and hardened FCW may not perform as expected.

Concrete surface should be free from any hydrostatic pressure. There are many methods to determine rate of water vapour transmission. Contact Concretech Technical Services if rate of water vapour transmission of the substrate exceeds 5 lbs per 1,000 sq.ft. per 24 hours. Contact Concretech technical services regarding concrete moisture and ways to control it.

INSTALLATION INSTRUCTIONSAll concrete surfaces to receive FCW shall be clean, free of oil, grease, dirt, efflorescence, excess moisture and foreign matter. Concrete surface should be sound, dimensionally stable, fully cured at least 28 days and free from hydrostatic pressure. Clean with commercial degreaser and rinse with plain water. Apply two coats steel primer on any exposed reinforcing steel.

Fill any open cracks longer than 2 mm (80 mils) with patching materials. For cracks less than 1/8” apply a thin coat of FCW 15- 25 cm (6- 10 “) wide, over the crack and lay Reinforcing Fabric on the wet FCW and

tamper in. Apply a second coat of FCW to completely cover the fibre. The amount of total FCW on the crack should not exceed 2mm (80 mils) thick.

Always install test areas to ensure compatibility of the FCW with the substrate, bond strength and the performance. A 16 Kg. (35.3 lb) bag of FCW Powder Component A combined with 4.8 L (5.07 US quarts) Component B polymer covers 90.0 square feet at 1.3 mm (50 mils). Two coats are required for optimum performance.

Mix one bag of FCW powder Component A with the entire contents of FCW Liquid Component B. Mix to a fluid, homogenous state. When poured on the floor mixed material flows very well and provides uniform coverage. FCW Powder Component A should be added gradually while stirring. Use a high speed drill to mix the material at about 600 rpm for 2 to 3 minutes. Lumps will form if FCW Powder is added suddenly into the liquid. Do not over mix. Moving the mixer up and down during the mixing process could cause air entrainment. Air pockets in the mud could shorten the working time and cause pin holing during application and curing. Pour the mud on the prepared substrate evenly. Wet mix on the substrate should flow and level by itself. Shortly after placing the wet mix, use a Gauge Rake to unify to a desired depth and then finish with a brush. FCW can also be applied using trowel or brush on smaller areas. A hopper gun with suitable spray nozzle may be used for faster and more uniform application. When spraying, brushing may be needed to avoid pinholes.

A second coat should be applied within 10-15 minutes, depending on temperature and relative humidity. It is important to apply the second coat not later than 15 minutes after the first coat. If application of the second coat takes longer, it may not bond well to the first coat. Full cure is 5 hours at 23oC (73oF).

Properly mixed FCW should not show any sign of bleed water or phase separation. Work as a team to provide continuous flow of wet mix in a large area. Fresh application must be protected from rain, intense sunlight and strong wind for 12 hours. Avoid walking on the surface for at least 7 hours after installation of FCW. Temperature and humidity play important role on curing and hardening. Do not drive a fork lift over for at least 48 hours after installation. Tools can be cleaned with water immediately after use.

Flex CementPositive and Negative Side Waterproof Coating

PRODUCT DESCRIPTIONFlexible Cement Waterproofing (FCW) is an elastomeric, polymer modified cement based membrane for waterproofing concrete structures on the negative and positive side. It is highly flexible, and will bridge concrete cracks of up to 1/8”. FCW provides a fast cure and excellent elongation even in extreme cold weather.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


PROPERTIESColor Light GreyWet Density 1.87 kg/litre Ph 11Thickness 1.3 mm (50 mils)/coatWorking Time 15-30 minutes Full Cure 5 hours @ 23C (73F)Tensile Strain (ASTM D412 mod, 20C) 20% (without fabric)Tensile Stress (ASTM D412 mod, 20C) 0.82 MPa (120 psi)Elongation @ 20 C > 100%

Water Vapor Permeance (ASTM E96) Wet Cup - 14.5 permsat 1.7 mm thickness Dry Cup – 3.8 perms

SAFETY PRECAUTIONSFirst Aid: Flush contaminated areas immediately and seek medical attention. Remove contaminated clothing. Wash hands with soap and water. Flush eyes with clean water or eye wash solution.



Flex CementPg. 2



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

USESFor use on all interior and exterior concrete panels where a homogenous and consistent color and finish is desired. Concretech Face Mix combines advanced polymer chemistry with GFRC backing to produce concrete facades and decorative pieces with exceptional strength and versatility.

PACKAGINGConcretech Face Mix is a two component material consisting of 1 gallon (3.78 litres) of liquid modifier and a 22.7 kg (50 lb) bag of cement Face Mix. The cement Face Mix is pre-colored to a variety of standard colors and can be custom colored upon request.

LIMITATIONSDo not place in thicknesses less then 1/4” or greater then 1/2”. Do not place when ambient temperature is below 3 degrees Celsius (40 degrees Fahrenheit). Ensure forming material is designed to inhibit bond or use a non-staining form release agent. Do not use over hydrocarbon based form release agents or where release agents puddle as staining and discoloration may result. Best results are obtained using forming medium that does not require a form release agent to inhibit bond.

INSTALLATION INSTRUCTIONSEnsure all forming materials are constructed and fastened correctly. Pour the entire contents of the Modifier into a clean, five gallon bucket. Pour 2/3 of the bag of face mix into the bucket and mix to a homogenous, lump free consistency. Add remaining modifier and continue to mix for an additional 2-3 minutes. For sprayable consistency, add up to 1.5 litres of clean water to desired consistency. Concretech Face Mix may be packed, poured or sprayed in place. For spray application use a hopper gun at a air flow of 8.3 cubic feet per minute at 40 PSI. Spray all horizontal and vertical surfaces to a minimum depth of 1/4” and a maximum depth of 1/2”. While product is still wet, embed reinforcing fabric and back up the facing mix with Glass Fibre Reinforced Concrete. Allow to fully cure before deforming or demolding.

PROPERTIESAppearance - concrete gray or available in a variety of standard and custom colors.

Yield - 20 square feet per bag at 1/4” thickness

Compressive Strength (ASTM C109) - 7,500 psi (53.5 Mpa) at 28 days

Flexural Strength (ASTM C348) -1,288 psi (8.28 Mpa)

Abrasion Resistance (ASTM D-4060) - 28 day - 0.6 grams loss with Taber H-22 500 gram load, 200 cycles

SAFETY PRECAUTIONSCaution - wear protective clothing, rubber gloves, eye protection and dust respirator mask. Prolonged exposure may result in respiratory illness. Keep away from children.

First Aid - flush contaminated areas immediately. Remove contaminated clothing. Wash with soap and water. Flush eyes with clean water or eye wash solution. Seek medial attention when necessary.


Face MixFacing Mix For Glass Fibre Reinforced Concrete

(GFRC)

PRODUCT DESCRIPTIONConcretech Face Mix is a two component pre-mixed concrete material combining advanced polymer and cement chemistry with glass fibre reinforcement (GFRC). Concretech Face Mix is designed to be used with GFRC concrete as backing to produce pre-cast wall panels, counter tops or decorative pieces.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


COMMON USES & APPLICATIONS:EPOTECH HIFLOW PRECISION DEEP POUR GROUT is a three component, epoxy system designed for grouting and anchoring heavy equipment and engines to thickness’ of 12 inches. This 100% solids system features exceptional strength, chemical resistance, flow and positive expansion.

EPOTECH HIFLOW PRECISION DEEP POUR GROUT is perfect for grouting, and anchoring heavy equipment. With proper preparation and mixing, our grout eliminates costly failures from curing cracks, expansion, shrinkage, corrosion, breakdown and oil degradation. EPOTECH HIFLOW PRECISION DEEP POUR GROUT provides resistance to vibration, impact, torque loads and other stresses. Affords outstanding resistance to acids, alkalis, solvents, oil and grease compared with concrete.

• Anchor Bolts • Engines• Rails • Compressors• Heavy Machinery • Base Plates • Patch Floors• Milling Machines & Presses • Pumps

FEATURES:• Resists impact and vibration•Improves machine operation•Provides dimensional stability•Eliminates curing cracks•Positive Expansion•Low stress curing process•Reduces long-term costs•Excellent chemical resistance compared to concrete•High physical strengths

PACKAGINGEPOTECH HIGHFLOW PRECISION DEEP POUR GROUT is packaged in 2.0 cubic foot units. The resin is in a pail and the hardener is packed in a bottle, and then a box. The graded silica aggregate sand is packed in 50 lb. bags.

YIELD:Kit weight Yield in cubic inches (5 bag) 228 lbs is 3456

INSTALLATION INSTRUCTIONS(See MSDS Sheet Before Using)Use EPOTECH HIFLOW PRECISION DEEP POUR GROUT in situations where clearance is ¾ inch or more. Abrade concrete by bush hammering, scarification, or similar method to remove laitance and contamination from surfaces. For maximum adhesion, steel should be sandblasted where possible. Concrete must be clean, dry and free from dust. Prior to mixing, all surface preparation, forming (including application of release agents to forms, bolts and nonadhering surfaces) and equipment organization must be completed. Material must be warm and dry (between 70º Fand 90ºF). Add the entire contents of the hardener to the resin in a slow speed mortar mixer or wheelbarrow and mix for 2 to 3 minutes or less. (One to several batches can be mixed at atime as required.) Slow speed mixing is mandatory to minimize air entrapment. Slowly add aggregate and mix to a homogenous blend. Pour the mixed material under the machine base. Keep grout flow steady. Allow the grout to set for a minimum of 24 hours at 70ºF before placing equipment into operation. Forms may be removed when a metallic sound results as grout is struck with a hammer.

PROPERTIES(7 day cure at 77º F)Compressive Strength (16 hours) 10,050 psiFull Cure 16,200 psiCompressive Modulus (ASTM C-579-82) 2.05 x 106 psiTensile Strength (ASTM C-307-83) 2,000 psiFlexural Strength (ASTM-C-580-74) 4,350 psiFlexural Modulus (ASTM C-580-74) 1.51 x l06 psiLinear Shrinkage Positive ExpansionCoefficient of Expansion (ASTM D296-70) 17.5 x l0-6 in/in/ºFPot Life 60 minutes at 77ºFCure Rate: Minimum 18 hours at 77ºF/25ºC

Full Cure5 to 7 days, depending upon application temperature, cure temperature and pour thickness.

Mixing Ratio:Supplied in factory proportioned quantities. Mix entire unit.Yield: ..............................................114 pounds per cubic footColors ................................................................................. Brown

EPOTECHPRECISION HIFLOW DEEP POUR GROUT

PRODUCT DESCRIPTIONEPOTECH HIFLOW PRECISION DEEP POUR GROUT Is an exceptional high strength, industrial epoxy grout designed for grouting and anchoring heavy equipment to thicknesses of 12 inches. Superior to cement grouts, our three-component epoxy HIFLOW PRECISION DEEP POUR GROUT eliminates costly failures due to curing cracks, shrinkage, expansion, corrosion breakdown and oil degradation. Superior formulation allows excellent flow. High filler loading and an expansion additive insure positive expansion, low exotherm and extremely high effective bearing area. The speed of the product has been carefully controlled to achieve adequate flow time yet high early cure strength.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

POT LIFE:Mixed components have a pot life of approximately 60 minutes at 75ºF.

TEMPERATURE LIMITATIONS:During the installation and cure, the surrounding concrete, steel surface and air temperatures must be between 50ºF and 90ºF. The grout should have a minimum temperature of 70ºF. To optimize performance, we recommend a minimum temperature of 70ºF for grout, surrounding concrete, steel surface and air. In cold weather we recommend building a shelter around the work area and warming to 70ºF. Above 90ºF areas must be protected from direct sunlight and provisions made to cool the material below 90ºF. Never pour in direct sunlight.

HARDENING AND CURE:EPOTECH DEEP POUR GROUT will harden to 10,050 psi in 16 hours at 77º F with full properties being achieved in 5 to 7 days.

STORAGE AND SHELF LIFE:Materials should be stored at room temperature (between 70º - 90º Fº). Stored at room temperature, materials should have a 1 year shelf life.

SAFETY PRECAUTIONSRead container labels and Material Safety Data Sheets before using all products. Contact with either component can cause irritation. Wear protective clothing. Cover hands with chemical resistant gloves. Wear chemical splash goggles to avoid eye contact. Use only with adequate ventilation.




Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


EPOTECHPg. 2

USESFast Patch is a general repair material formulated for a wide range of patching applications. Fast Patch can be used on masonry or horizontal and vertical concrete surfaces in need of restoration.

BENEFITS• Ready-to-use• Early strength gain for fast turnaround• Versatile• Concrete Gray in colour• Good freeze-thaw resistance• Can be extended with pea gravel for high volume pours• Can be polymer modified for ease of application

PREPARATIONSSurface should be structurally sound and free of foreign material like oil and grease. Patch area should be routed to a minimum thickness of 1”X1”. Saturate patch area with potable water prior to applying Fast Patch.

PACKAGINGAvailable in 22.7 kg (50 lb.) multi-wall paper bags.

LIMITATIONSDo not mix more Fast Patch then can be placed within 5 minutes. Do not use Fast Patch in joints and cracks subject to movement or dynamic and cyclic loading.

INSTALLATION INSTRUCTIONSMix Fast Patch to a stiff, plastic consistency by means of a mechanical mixer. Do not mix more Fast Patch then can be placed within 5 minutes.Fast Patch can be extended using well graded 3/8” stone by adding up to 0.5 cubic feet per bag. Shave excess Fast Patch to the substrate profile prior to final set. Moisture Cure Fast Patch for up to one hour.

PROPERTIES

Appearance: Concrete Colour Yield: 60 bags per cubic meter or 0.5 cubic feet per bag Shelf Life: Approximately 1 year when stored properly Drying Time: Initial: 10 minutes, Final: 25 minutes Compressive Strength: 2 hours: 1150 psi (10 Mpa) 3 days: 3500 psi (24 Mpa) 28 days: 5000 psi (35 Mpa)

SAFETY PRECAUTIONSFast Patch is a blend of Portland Cement and Silica Sand. Appropriate Safety Wear like dust masks, rubber gloves and safety glasses should be worn throughout the handling, mixing and placing process. Consult Fast Patch MSDS for further information.


Fast PatchEarly Strength Concrete and Masonry Repair

Material

Product DescriptionFast Patch is a pre-blended fast setting repair mortar for repairing concrete and masonry structures. Fast Patch is formulated for early strength and can be extended with 3/8” washed well-graded aggregate for high volume repair projects.

Fast Patch can be polymer modified for feather-edge applications and where a superior bond to existing surface is required.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESH-Patch is hand formed into stable cracks and joints in concrete to stop leaks. H-Patch is used in basement foundations, tunnels, and sewers, precast water tanks and concrete piping. H-Patch can be used on horizontal, vertical and overhead applications.

• Ready-to-use• Very Rapid Setting• Can be hand formed for emergency water stop• Versatile• Will not stain or discolour

H-Patch can be batched on request using Type 50 Cement for resistance to sulphates for wastewater and sewer applications.

PACKAGINGAvailable in 4 kg (8.8 lbs) plastic pails.

LIMITATIONSDo not mix more H-Patch then can be placed within 30 seconds. Do not use H-Patch in joints and cracks subject to movement or dynamic and cyclic loading.

INSTALLATION INSTRUCTIONSSurface should be structurally sound and free of foreign material like

oil and grease. Mix H-patch to a plastic consistency by means of a mechanical mixer. Do not mix more H-Patch then can be placed within 30 seconds. Hand Form H-Patch into patching area. Hold in place and maintain pressure until H-Patch achieves initial set. Shave excess H-Patch to the substrate profile prior to final set. Moisture Cure H-Patch for 30 minute. For use as a water stop, apply dry H-Patch by hand to patch area and allow the water to harden the H-Patch. Repeat until patch is complete.

PROPERTIESColor: Concrete gray compressive strength 30 mpaSet Time <30 Seconds

SAFETY PRECAUTIONSH-Patch is a blend of Portland Cement, Silica Sand and highly caustic admixtures. Appropriate Safety Wear like dust masks, rubber gloves and safety glasses should be worn throughout the handling, mixing and placing process. Consult H-Patch MSDS for further information.


H-PatchVery Rapid Setting Patch & Water-Stop

PRODUCT DESCRIPTIONH-Patch is a pre-blended Hydraulic Patch and Water-Stop designed to stop running and seeping of water in concrete and masonry structures.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use as a topping between 1/16” - 1/8” on interior and exterior concrete, colored and flat work concrete as well as any typical area where concrete or decorative color is used. It is good for pool decks, patios and walkways. Ultrabond Topping L3 mixed with Broom Coat can also be sprayed and used as a trowel knockdown finish. Broom Coat can be colored with Concretech Iron Oxide Pigments.

PACKAGINGBroom Coat is available in 22.7 Kg. ( 50 lb.) bags.

LIMITATIONSDo not use over poor quality substrate. Do not place in thickness greater than 1/8”. Do not use when temperature is less than 3°C (38°F), when temperature is expected to fall below 2°(36°F) or when inclement weather is expected during the first 24 hours after placement. Surfacesto be covered require at least two coats of Ultrabond Primer as a primer before applying topping. Primer is to be touch dry between coats and dried clear before applying topping. Refer to Concretech Architectural Specifications for installation procedures, base preparation, forming and product information. Do not cure with plastic sheets, water or curing agents that may discolor the surface. Do not leave wood or other products on the surface while curing, as this will cause discoloration.

INSTALLATION INSTRUCTIONSAll concrete to receive the mixture of Ultrabond Topping Polymer L3 and Broom Coat shall be clean, free of oil, grease, dirt, efflorescence, drywall residue, excess moisture and foreign matter. Clean with commercial degreaser and rinse with plain water. Allow to fully dry before priming. Prime all surfaces with at least two coats of Ultrabond Primer. Primer should be touch dry between coats and dried clear before applying topping.

Mixing: Pour 6 litres . (1.5 Gal.) of Ultrabond Topping Polymer L3 into clean pail and add 3/4 of a bag of Broom Coat and mix with drywall mud paddle drill for 30 seconds. Add remainder of Broom Coat and mix to consistency by adding up to 2 L (0.5 gal) of L3 Polymer and mix for at least two minutes.

Note: Wide range of polymer addition is engineered for suitability of application. Do not change addition rates once project is started as this may cause different color and cure rates. For best results pour and

trowel into place within 3 minutes of mixing. Remix material that is not placed within 5 minutes.

Note: Slight color changes can be expected if addition ratios, batching procedures or mix times are altered. Pour mixed Broom Coat onto surface in consistent thickness and trowel or spray to smooth even finish. Hold trowel as flat as possible and lightly skim over surface using irregular motion to prevent repetitive trowel lines. See Technical Bulletin for each product before using. Allow mixed Broom Coat to cure until hard before cleaning, coloration and/or sealing. All colored concrete surfaces shall have a sealer or water repellent coating applied to protect the finish from moisture and oxidization. For exterior applications apply Concretech Cure and Seal (CS-15) as soon as possible. Follow up with Concretech High Solids Sealer (CS-25 or CS- 30) after 28 days. For interior applications epoxy and/ or urethane coatings and sealers may be used. Test compatibility in small area before attempting full application. Follow Concretech technical bulletins for the applied product.

STORAGE AND HANDLINGMaintain storage temperature at 10-30°C (50-86°F). Expected shelf life if stored at recommended temperature is one year. Keep from freezing. Store in a cool and dry place. Store in a well ventilated area. Avoid all skin contact. Avoid contact with eyes. Avoid inhaling.

PROPERTIESCustom colors are matched upon request1.5 to 2.0 Gal. (6.0 L.-8.0 L.) of Ultrabond Topping Polymer L3 with 1 bag of Broom Coat covers 100 SqFt @ 1/16” thickness. SAFETY PRECAUTIONSCaution: Broom Coat contains portland cement and silica sand. Wear protective clothing, rubber gloves, and eye protection and dust respirator mask. Prolonged exposure may result in respiratory illness. Keep away from children.


Broom Coat , Grey and White

PRODUCT DESCRIPTIONBroom Coat is a topping Powder designed for use as overlay and develops 7000-psi strength after 28 days. Broom Coat is to be used with Ultrabond Topping Polymer L3 for mixing and Ultrabond Primer as a prime coat. Broom Coat rejuvenates abraded or dis-colored concrete.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use as a topping from ¼“ to ½” thickness on all interior and exterior concrete, stamped concrete, colored and flat work concrete as well as any typical area where concrete or decorative color is used.

PACKAGINGConcretech Grey/White Stamp is available in 50 lb bags. Custom blended colors are available upon request. UltraBond Primer and Ultrabond Polymer L1 are available in 1 gallon and 5-gallon containers.

LIMITATIONSDo not use over poor quality substrate. Do not place in thickness less than ¼ or greater than ½ in one application. Do not use when temperature is less than 38° F, when temperature is expected to fall below 36° F or when inclement weather is expected during the first 24 hours after placement. Surfaces to be covered require at least two coats of UltraBond Primer as a primer before applying topping. Primeris to be touch dry between coats and dried clear before applying topping. Do not apply primer more than 24 hours before placement. Refer to Concretech Architectural Specifications for installation procedures, base preparation, forming and product information. Do not cure with plastic sheets, water or curing agents that may discolor thesurface. Do not leave wood or other products on the surface while curing, as this will cause discoloration.

INSTALLATION INSTRUCTIONSAll concrete to receive the Grey/White Stamp shall be clean, free of oil, grease, dirt, efflorescence, drywall residue, excess moisture and foreign matter. Clean with commercial degreaser and rinse with plain water. Allow to fully dry before priming. Prime all surfaces with at least two coats of UltraBond Primer. Primer should be touch dry between coats and dried clear before applying topping. Pour 1 gallon of Ultrabond Polymer L1 liquid into clean pail and add ¾ of the Grey/White Stamp powder and mix with drywall mud paddle on ½ drill for 30 seconds. Add remainder of Grey/White Stamp powder and mix for at least two minutes. Note: 10% more Ultrabond Polymer L1 may be added if

more workability is desired. For best results pour and trowel into place within 3 minutes of mixing. Remix material that is not placed within 5 minutes. Note: Slight color changes can be expected if addition ratios, batching procedures or mix times are altered. Pour mixed Grey/White Stamp onto surface in consistent thickness and trowel to smooth even finish. Hold trowel as flat as possible and lightly skim over surface using irregular motion to prevent repetitive trowel lines. Allow Grey/White Stamp to cure until plastic stage set is firm for stamping before using release powder or liquid release. See Technical Bulletin on each product before using. Allow Grey/White Stamp to cure until hard before removing release powder, cleaning, coloration and/or sealing. All colored concrete surfaces shall have a sealer or water repellant coating applied to protect the finish from moisture and oxidization. Apply Concretech Cure and Seal (CS 15) as soon as possible. Follow up with Concretech High Solids Sealer (CS 25 or CS 30) after 28 days. Follow Concretech technical bulletins for the applied product.

PROPERTIESBase colors Grey or WhiteCustom colors available

SAFETY PRECAUTIONSCaution – The product contains Portland cement and silica sand. Wear protective clothing, rubber gloves, and eye protection and dust respirator mask. Prolonged exposure may result in respiratory illness. Keep away from children.



Grey/White Stamp

PRODUCT DESCRIPTIONGrey/White Stamp powder is a trowel grade topping designed for use as a stampable overlay, trowel overlay, patching and repair mortar. 28-day strength is 7000 psi. Grey/White Stamp powder is to be used with L-1 Polymer liquid for mixing and UltraBond Primer.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESThe product can be colored with dyes, acid stains and treated with sealers such as epoxy and urethane based coatings. It can also be used to smoothen and repair interior concrete surfaces before installation of any floor coverings. Ceramic tiles and natural stones can be applied over within 5 to 7 hours after application. Carpet, vinyl sheet, vinyl tile or any other floor topping can be installed 16 to 24 hours after application. Show rooms, retail stores, building entrances, corridors, restaurant floors, and hotel lobby floors can be decorated with SLO with any desired integral color and finish. A smooth, glass like surface will result when finished with diamond polish.

BENEFITSCan re-surface existing concrete and install treatments to create a decorative concrete finish.

PACKAGING22.7 kg (50 lb) bags.

LIMITATIONSFor interior use only.

PREPARATIONSAll concrete surfaces to receive SLO shall be clean, free of oil, grease, dirt, efflorescence, drywall residue, excess moisture and foreign matter. Concrete surface should be sound, dimensionally stable, fully cured at least 28 days and free from hydrostatic pressure. Clean with commercialdegreaser and rinse with plain water. Allow to fully dry before priming. Fill the holes, cracks with appropriate joint filler. Use patching materials to fill deep cracks or holes. Prime all surfaces with at least two coats of Concretech Ultrabond Topping Primer. Primer should be touch dry between coats and dried clear before applying topping.Always install test areas to ensure compatibility of the SLO with the substrate, bond strength and the performance of primer and topping system. Porous concrete substrates may require epoxy bonding primer such as Concretech Ultrabond 700 for better performance.

INSTALLATION INSTRUCTIONSMix one bag of SLO with the required amount of water. Use a proper mixing container, pour 5.25 L (5.55 US qts) clean, cold potable water. Add one bag (50 lb or 22.7 kg) of SLO powder while stirring. Use high speed drill to mix at about 800 rpm for two to three minutes to a homogeneous, lump-free and consistent mud. Pour the mud on the prepared substrate evenly. Do not over mix. Moving the mixer up

and down during the mixing process could cause air entrainment. Air pockets in the mud could shorten the working time and cause pin-holing during application and curing. Do not bridge expansion joints and control joints. Pour wet fluid on the substrate, it should flow and level by itself. Shortly after placing the wet mix, use a Gauge Rake to unify to a desired depth and Smoother (Leveller) to obtain an even surface. Working time is 10 minutes. Depending on humidity, it takes 5 hours at 23ºC (73ºF) to harden and is ready to accept sealer or any other coloring applications. Properly mixed SLO should not show any bleed water or phase separation. Work as a team to provide continuousflow of wet mix in a large area. This will help the uniformity of the surface. Pour SLO in a ribbon pattern while maintaining a wet edge. If a wet edge cannot be maintained, reduce the width of the pour. Avoid walking on the surface for at least 5 hours after installation. Room temperature and humidity play important roles on curing and hardening. Protect the SLO from traffic, dirt and dust until sealer or coating has been applied. Do not drive a fork lift over the surface for at least 48 hours after installation. Full cure is obtained in 10 days at 23ºC (70ºF).

PROPERTIESAppearance: light grey powder/white powderYield: 40 sqft/ bag @ 1/8” thicknessShelf Life: Shelf life under normal conditions is one year. Working Time: 10 minutesDry Time: Initial Set: 2 hoursFinal Set: 3 hoursOpen to walking traffic 5-7 hoursCarpet Tile/Stone installation 5-7 hours

Acid Stains/Sealer install 16-24 hoursCompressive Strength: 1 day 2500 psi (17.2 MPa)ASTM C-109 7 day 3500 psi (24.1 MPa) 28 day 4500 psi (31.0 MPa)Flexural Strength: 1 day 700 psi (4.83 MPa)ASTM C-348 7 day 1100 psi (7.59 MPa) 28 day 1288 psi (8.28 MPa)Abrasion Resistance:ASTM D-4060 28 day – 0.6 grams loss with Taber H-22 500 gram load, 200 cyclesVolume ChangeASTM C-157 28 day – 0.06%

Self Level Overlay (SLO)Self Leveling Underlayment or Wear Surface

PRODUCT DESCRIPTIONSelf Levelling Overlay (SLO) is a fast setting, self levelling concrete topping and underlayment. It is designed for resurfacing interior floors. SLO may be stained or polished to create architectural finishes. SLO needs to be placed over a properly prepared, primed substrate. Light traffic concrete floors may be primed with water based acrylic primer, Concretech Ultrabond Topping Primer and heavy traffic floors may be primed with 100% solid epoxy bonding primer, Concretech Ultrabond 700. SLO is available in white and grey base.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147




.TECHNICAL SERVICESComplete technical information is available from Concretech Inc. and its authorized applicators and distributors. In house laboratory testing is available for specialty applications. Technical services available in North America call toll free 1.888.503.6780



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


Self Level Overlay (SLO)Pg. 2

USESLightweight Concrete – LW 123 can be used in non-structural concrete blocks and panels for outer leaves of buildings, for architectural ornamentation and in pre-cast and cast in place ornamental concrete applications. Ideal for use in concrete partition walls, concrete roof slabs and floor screeds, LW 123 can also be used for concrete countertop work and can be stained, dyed and polished. A high quality finish results when used in precast and cast in place applications.

PACKAGINGLightweight Concrete – LW 123 is available in 27 lb (12.2 kg) bags, yielding 0.42 cubic feet per bag.

LIMITATIONSDo not use over poor quality substrate. Do not use when temperature is less than 38ºF (3ºC), when temperature is expected to fall below 36ºF (2ºC) or when inclement weather is expected during the first 24 hours after placement. Do not cure with plastic sheets, water or curing agents that may discolor the surface. Do not leave wood or other products on the surface while curing, as this will cause discoloration. Lightweight Concrete – LW 123 is designed as a reduced mass concrete material for architectural installations and should not be used in structural applications. Contact Concretech Technical Services for additional information or design considerations 1-877-952-0157

INSTALLATION INSTRUCTIONSAll substrates to receive Lightweight Concrete – LW 123 shall be clean, free of oil, grease, dirt, efflorescence, drywall residue, excess moisture and foreign matter. Clean with commercial degreaser and rinse with plain water. Substrates should be sound, dimensionally stable and free from hydrostatic pressure. If the substrate is a cement based concrete material, it should be fully cured for 28 days prior to applying Lightweight Concrete – LW 123 as a overlayment. Fill any holes or cracks in the substrate with appropriate patching and crack filling materials.

Always install test areas to ensure compatibility of Lightweight Concrete – LW 123 with the substrate and to verify bond strength and performance. Depending on the mold, a concrete release agent may or may not be necessary. Contact Concretech Technical Services to discuss appropriate release agents for intended applications.

Mix one bag 27 lb/12.3 kg of Lightweight Concrete – LW 123 with 3.4 US qts/3.2 L in a clean container with a high speed drill and mixing paddle at 700 rpm for 1-2 minutes. LW 123 should be mixed to a homogenous, lump-free and consistent mud. DO NOT OVERMIX. Care should be taken to avoid entraining air. Excessive upwards and downwards motion with the mixing drill may cause air entrainment. Air entrainment may reduce working time and cause pin-holing during application and curing. Evenly apply the mixed material to the substrate or forming medium. Working time is 10 minutes. LW 123 will harden in approximately five hours at 73ºF (23ºC). LW 123 may receive sealers and color applications that are not sensitive to hydrating moisture after ten hours.

Avoid traffic for 10 -12 hours. Full cure is obtained in ten days at 73ºF (23ºC).

STORAGEMaintain storage temperature at 10 – 30ºC (50-86ºF). Expected shelf life if stored at recommended temperature is one year. Keep from freezing. Store in a cool and dry place. Store in a well ventilated area. Avoid all skin contact. Avoid contact with eyes.

PROPERTIESMixing Ratio: 3.4 qts. / 3.2 litres of water per bagDry Density: 70 lbs / cu ft (1.12 kg/litre)PH: 11Working Time: 10 MinutesOpen to foot traffic: 5-7 hoursCompressive Strength: (ASTM C109): 2850 psi (19.5 MPa)Volume Change: (ASTM C157): 0.08% after 28 days


Lightweight ConcreteLW 123

PRODUCT DESCRIPTIONLightweight Concrete – LW 123 is a new kind of concrete with good strength and durability. The product is 50% the weight of normal concrete products. This reduced mass makes the material ideal for a variety of applications. The advantage of Lightweight Concrete – LW 123 is its reduced mass while maintaining sufficient strength.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use in ultrabond topping from ¼ to 1” thickness on all interior and exterior concrete, stamped concrete, colored and flat work concrete as well as any typical area where concrete or decorative color is used.

PACKAGINGUltraBond Topping Polymer available in 3.78 L. / 1 Gal. and 18.9 L. / 5Gal. containers.

LIMITATIONSDo not use Ultrabond Topping Polymer and Ultrabond Topping mixture over poor quality substrate. Do not place in thickness less than ¼” or greater than 1” in one application. Do not use when temperature is less than 3°C (38°F), when temperature is expected to fall below 2°C (36°F) or when inclement weather is expected during the first 24 hours after placement. Surfaces to be covered require at least two coats of UltraBond Primer as a primer before applying topping. Primer is to be touch dry between coats and dried clear before applying topping. Do not apply primer more than 24 hours before placement. Refer to Concretech Architectural Specifications for installation procedures, base preparation, forming and product information. Do not cure with plastic sheets, water or curing agents that may discolor the surface. Do not leave wood or other products on the surface while curing, as this will cause discoloration.

INSTALLATION INSTRUCTIONSAll concrete to receive the UltraBond Topping Powder and UltrabondPolymer mixture shall be clean, free of oil, grease, dirt, efflorescence, drywall residue, excess moisture and foreign matter. Clean with commercial degreaser (Concretech R/A Soap) and rinse with plain water. Allow to fully dry before priming. Prime all surfaces with at least two coats of UltraBond Primer. Primer should be touch dry between coats and dried clear before applying topping. Pour 1 gallon of UltraBond Topping Polymer into clean pail and add ¾ of the UltraBondTopping Powder and mix with drywall mud paddle drill for 30 seconds Add remainder of UltraBond Topping Powder and mix for at least two minutes. Note: 10% more UltraBond Topping Polymer may be added if more workability is desired. For best results pour and trowel into place within 3 minutes of mixing. Remix material that is not placed within 5

minutes. Note: Slight color changes can be expected if addition ratios, batching procedures or mix times are altered. Pour mixed UltraBond Topping onto surface in consistent thickness and trowel to smooth even finish. Hold trowel as flat as possible and lightly skim over surface using irregular motion to prevent repetitive trowel lines. Allow UltraBond Topping mixture to cure until plastic stage set is firm for stamping before using Release Powder or Liquid Release. See Technical Bulletin for each product before using. Allow UltraBond Topping mixture to cure until hard before removing, Release Powder, cleaning, coloration and/or sealing. All colored concrete surfaces shall have a sealer or water repellent coating applied to protect the finish from moisture and oxidization. Apply Concretech Cure and Seal (CS- 15) as soon as possible. Follow up with Concretech High Solids Sealer (CS-25 or CS-30) after 28 days. Follow Concretech technical bulletins for the applied product.

STORAGEMaintain storage temperatures at 10-30°C (50-86°F). Expected shelf life if stored at recommended temperature is one year. Keep from freezing. Store in a cool and dry place. Store in a well ventilated area. Avoid all skin contact. Avoid contact with eyes. Avoid inhaling.

PROPERTIESSquare Footage 3.78 L. / 1 Gal. Ultrabond Topping Polymer and 1 BagUltrabond Topping Powder covers 22-25 SqFt. at ¼” thickness depending on surface and roughness

SAFETY PRECAUTIONSCaution – Contains Portland cement and silica sand. Wear protective clothing, rubber gloves, and eye protection and dust respirator mask. Prolonged exposure may result in respiratory illness. Keep away from children.


Ultrabond Topping Polymer

PRODUCT DESCRIPTIONUltraBond Topping Polymer is a polymer liquid designed to be mixed with Ultrabond Topping Powder and to be used as a stampable overlay, trowel overlay, patching and repair mortar.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESUltraBond Topping Primer is intended for use over precast or cast in place concrete, slate, bricks and stucco. UltraBond Topping Primer will adhere to itself in the event repriming is needed. It is easy to apply and it reduces porosity of the substrate.

PACKAGINGUltraBond Topping Primer is available in 3.78 L. / 1.0 Gal. Containers,18.9 L. / 5.0 Gal. Containers and 208 L. / 55 Gal. Plastic Drums

LIMITATIONSDo not use over epoxy-coated floors, asphalted materials and gypsum based underpayment substrates. Protect UltraBond Topping Primer from freezing. Prolonged freezing may damage the primer. Thaw the frozen primer gradually.

INSTALLATION INSTRUCTIONSAll concrete to receive the UltraBond Topping Primer shall be clean, free of oil, grease, dirt, efflorescence, drywall residue, excess moisture and foreign matter. Clean with commercial degreaser (Concretech RASoap) and rinse with plain water. Allow to fully dry before priming.Prime all surfaces with at least two coats of UltraBond Topping Primer.UltraBond Topping Primer does not need dilution. It can be applied by

brush, roller, or airless spray. Back rolling after spraying is recommended to ensure even coverage and full encapsulation of the fine dust particles. Apply UltraBond Topping Primer at a rate of 4.0 mils wet film thickness. Avoid ponding and pudddling. Primer should be touch dry between coats and dried clear before applying topping. It takes 1.0 hour at 20°C (70°F) and 50 % R.H. to dry. At lower temperatures or higher relative humidity, drying takes longer.

STORAGEMaintain storage temperatures at 10-30°C (50-86°F). Expected shelf life if stored at recommended temperature is one year. Keep from freezing. Store in a cool and dry place. Store in a well ventilated area. Avoid all skin contact. Avoid contact with eyes. Avoid inhaling.

PROPERTIESSquare Footage is 350- 450 Sqft 3.78 L. (1.0 Gal.) (depending on surface porosity.)


Ultrabond Topping Primer

PRODUCT DESCRIPTIONUltraBond Topping Primer is water-based acrylic film forming primer designed primarily for priming concrete; brick, stucco and cement plaster surfaces prior to placing the UltraBond Topping Powder or Broom Coat. It is a milky liquid primer that dries to clear film over the surface to help reduce the suction in the substrate, providing easier application and better adhesion.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use as a topping with a thickness of 1/16” interior and exterior concrete, colored and flat work concrete as well as any typical area where concrete or decorative color is used. It is good for pool decks, patios and walkways. Ultrabond Topping L3 mixed with Broom Coat can also be sprayed and used as a trowel knockdown finish.

PACKAGINGAvailable in 1 gal. (3.78 L) jugs and 55 gal (205 L) Drums.

LIMITATIONSDo not use over poor quality substrate. Do not place in thickness greater than 1/8” Do not use when temperature is less than 3°C (38°F), when temperature is expected to fall below 2°(36ºF) or when inclement weather is expected during the first 24 hours after placement. Surfaces to be covered require at least two coats of Ultrabond Primer as a primer before applying topping. Primer is to be touch dry between coats and dried clear before applying topping. Do not apply primer more than 24 hours before placement. Refer to Concretech Architectural Specifications for installation procedures, base preparation, forming and product information. Do not cure with plastic sheets, water or curing agents that may discolor the surface. Do not leave wood or other products on the surface while curing, as this will cause discoloration.

INSTALLATION INSTRUCTIONSAll concrete to receive the mixture of Ultrabond Topping Polymer L3 and Broom Coat shall be clean, free of oil, grease, dirt, efflorescence, drywall residue, excess moisture and foreign matter. Clean with commercial degreaser and rinse with plain water. Allow to fully dry before priming. Prime all surfaces with at least two coats of Ultrabond Primer. Primer should be touch dry between coats and dried clear before applying topping.

Mixing: Pour 6 to 8 L. (1.5 to 2.0 Gal.) of Ultrabond Topping Polymer L3 into clean pail and add 3/4 of the Broom Coat and mix with drywall mud paddle drill for 30 seconds. Add remainder of Broom Coat and mix for at least two minutes.

Note: Wide range of polymer addition is engineered for suitability of application. Do not change addition rates once project is started as this may cause different color and cure rates. For best results pour and

trowel into place within 3 minutes of mixing. Remix material that is not placed within 5 minutes.

Note: Slight color changes can be expected if addition ratios, batching procedures or mix times are altered. Pour mixed Ultrabond Topping Polymer L3 onto surface in consistent thickness and trowel or spray to smooth even finish. Hold trowel as flat as possible and lightly skim over surface using irregular motion to prevent repetitive trowel lines. See Technical Bulletin for each product before using. Allow mixed Ultrabond Topping Polymer L3 to cure until hard before cleaning, coloration and/or sealing. All colored concrete surfaces shall have a sealer or water repellent coating applied to protect the finish from moisture and oxidization. For exterior applications apply Concretech Cure and Seal (CS-15) as soon as possible. Follow up with Concretech High Solids Sealer (CS-25 or CS-30) after 28 days. For interior applications epoxy and/ or urethane coatings and sealers may be used. Test compatibility in small area before attempting full application. Follow Concretech technical bulletins for the applied product.

STORAGEMaintain storage temperature at 10-30°C (50-86°F). Expected shelf life if stored at recommended temperature is one year. Keep from freezing Store in a cool and dry place. Store in a well ventilated area. Avoid all skin contact. Avoid contact with eyes. Avoid inhaling.

PROPERTIESUltrabond Topping Polymer L3: milky white acrylic emulsion1.5 to 2.0 Gal. (6.0 L.-8.0 L.) of Ultrabond Topping Polymer L3 with 1 bag (55lbs.) of Broom Coat covers 100 SqFt.

SAFETY PRECAUTIONSCaution: Broom Coat contains portland cement and silica sand. Wear protective clothing, rubber gloves, and eye protection and dust respirator mask. Prolonged exposure may result in respiratory illness. Keep away from children.º


Ultrabond Topping Polymer L3

PRODUCT DESCRIPTIONUltrabond Topping Polymer L3 is a topping liquid designed for use in overlay with 7000-psi strength after 28 days. Ultrabond Topping Polymer L3 is to be used with Broom Coat for mixing and Ultrabond Primer as a prime coat.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESConcretech SIlane-Q HD is used on brick, stone, masonry and concrete to reduce weight gain from water adsorption and to reduce chloride ion penetration. Concretech Silane-Q HD creates a hydrophobic surface.

• High and long lasting water repellency• Protects substrates from water and water-borne salt• Water repellant surfaces retain normal vapour transmission

characteristics• Deeply penetrating and will not attract airborne dirt• Reduces efflorescence• Conforms to the most stringent test requirements of NCHRP,• ASTM and AASHTO

PACKAGING18.9 Litre (5 Gallon) pail

LIMITATIONS• Do not use on previously sealed substrates• Contains solvents• Do not dilute Silane-Q HD with solvents as it will affect• the performance

INSTALLATION INSTRUCTIONSSurfaces should be clean and free of all laitance, oil, grease and other foreign substance and surface coatings. Concrete should be free of all standing water prior to applying Concretech Silane-Q HD. All concrete and masonry surfaces should be well cured.

• Ensure surface is clean• Apply Silane-Q HD on thoroughly cured surfaces

• Apply by airless sprayer, roller or brush• Apply in a heavy coat to increase penetration• On vertical surfaces, apply two wet-on-wet coats

PROPERTIESAppearance: Water-white to straw coloured liquid Yield: Apply at 100 square feet per gallonShelf Life: 6 months, when stored properlyActive: Monomeric alkylalkoxysilane

Applicable Standards:Meets NCHRP-244, ASTM C-672, AASHTO – 259/260 Salt Ponding

Weight Gain Reduction: >80%Chloride Ion Reduction: >82%

SAFETY PRECAUTIONSConcretech Silane-Q HD is formulated using aromatic hydrocarbons. These solvent carriers are released to the atmosphere during the application process and can accumulate in enclosed areas creating an ignition hazard. Adequate ventilation should be considered prior to applying Silane-Q HD in enclosed areas. Various solvents contain chemicals known to be embryonic toxicants. Consult MSDS for further information


Silane-Q HDMonomeric Alkylakoxysilane in Aromatic

Hydrocarbon

PRODUCT DESCRIPTIONConcretech Silane-Q HD is a monomeric alkylalkoxysilane in aromatic hydrocarbon that is reactive with the minerals contained in concrete, masonry and other substrates. The monomer penetrates deeply into a substrate and then reacts to form a protective surface surrounding each microscopic particle. This protective surface is extremely durable and leads to significant improvements in weather resistance and the ability for the substrate to resist water and chloride penetration.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor use on all interior and exterior concrete, stamped concrete, exposed aggregate, colored and flat work concrete for both curing and sealing of the concrete structure. Acrylic Cure and Seal 25% and 30% are designed to be used on interior or exterior concrete surfaces where color depth and higher gloss are desired at early cure stage. These higher solids cure and seal products are ideal for architectural slabs, wood, walkways, driveways, ramps, bridge decks, columns and beams. CS15 and CS20 are designed to be used as a cure and seal compound on interior or exterior concrete smooth trowel or broom finish surfaces.

PACKAGINGCS Series Sealers are ready to use and are available in 3.78 L. /1 Gal., 18.9 L. /5 Gal. and 207.9 L. /55 Gal. containers.

LIMITATIONSStandard Use:Do not apply when temperature is below 7ºC/45ºF or above 22ºC/72ºF. Surface must be clean, free of contaminates, oil, dirt, grease, mildew and moss. Take caution when using during windy conditions or where rapid air movement exists. Do not apply when rain or inclement weather is anticipated in the first 12 hours after application. Surface must be dry before applying any sealer.

Standard Use:Do not apply when temperature is below 7ºC/45ºF or above 22ºC/72ºF. Surface must be clean, free of contaminates, oil, dirt, grease, mildew and moss. Take caution when using during windy conditions or where rapid air movement exists. Do not apply when rain or inclement weather is anticipated in the first 12 hours after application. Surface must be dry before applying any sealer.

Premium Use:Do not apply when temperature is below 7ºC/45ºF or above 29ºC/84ºF. Precaution should be taken to

INSTALLATION INSTRUCTIONSProtect all surfaces that are not intended to receive cure and seal. Protect vegetation and landscaping. Finish all touch up work, detailing, cleaning and surface coloration. Apply Concretech CS Series Cure and Seal with pump up airless sprayer ensuring a continuous membrane immediately after the surface sheen has disappeared. Do not leave excess sealer in joints, grout lines or low spots. Contractors must use a sprayer designed for use with solvents. Other equipment may explode or fail, resulting in harm to persons or surrounding surfaces. All colored and imprinted concrete surfaces shall have a sealer or water repellent coating applied after 28 days.

STORAGEStore away from heat source, open flame or spark. CS Series Cure and Seals are flammable. Store in cool dry area out of direct sunlight. Shelf life under normal conditions is two years. Store in sealed containers ventilated areas only. Prevent contact with all sources of ignition, heat, spark and electric tools. Caution Flammable! Wear protective clothing, rubber gloves and eye protection. Prolonged exposure may result in respiratory illness, dizziness or damage to the nervous system. Contractor shall abide by all agency regulations for application, use, storage and disposal of solvent based materials. Keep away from children.

PROPERTIESColor ClearDry Time 30-55 minutes @ 21C (70F)Coverage:VOC CS15 Apply at 225 sqft/galVOC CS20 Apply at 250 sqft/galVOC CS25 Apply at 275 sqft/galVOC CS30 Apply at 275 sqft/gal

Standards Complies with ASTM C309

Concretech CS Series Sealers are available in VOC Compliant formulation for all states and In Canada. For regulations at or below 400 g/L of VOC, Concretech CS Series Sealers are available in Premium Use and Standard Uses formulation. Premium Use grade CS Series Cure and Seal provide longer working time and delayed evaporation rates to allow contractors maximum ease of application.



CS Series SealersVOC 400 - CURE & SEAL

PRODUCT DESCRIPTIONConcretech CS Series Cure and Seal VOC 400 are quality, abrasion resistant, durable, solvent based acrylic cure and seal for concrete curing and sealing and protection and highlighting color and contain 400 grams of Volatile Organic Compounds per litre or less.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

Concretech Inc.’s sole warranty is that our products have been manufactured to meet with our written specifications. The information herein is general informa-tion to assist our customers in determining whether our products are suitable for their applications. Our products are intended for sale to commercial and industrial customers. We require customers to inspect and test our products before use and to satisfy themselves as to contents, suitability and applications. Nothing herein shall constitute any other warranty, express or implied, including any warranty of merchantability or fitness for a particular purpose, nor is any protection from any law or patent inferred. All patent and trademark rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for incidental or consequential damages.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

Concretech Inc.’s sole warranty is that our products have been manufactured to meet with our written specifications. The information herein is general informa-tion to assist our customers in determining whether our products are suitable for their applications. Our products are intended for sale to commercial and industrial customers. We require customers to inspect and test our products before use and to satisfy themselves as to contents, suitability and applications. Nothing herein shall constitute any other warranty, express or implied, including any warranty of merchantability or fitness for a particular purpose, nor is any protection from any law or patent inferred. All patent and trademark rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for incidental or consequential damages.

DecaThane 200Pg. 2

USESFor use on all interior and exterior concrete, stamped concrete, exposed aggregate, colored and flat work concrete. Acrylic Sealer CS25 and CS30 are designed to be used on interior or exterior concrete surfaces. It is ideal for architectural slabs, wood, walkways, driveways, ramps, bridge decks, columns and beams. It can also be used as a sealer on exposed aggregate and old or new concrete surfaces and as a finish coat for Acrylic Sealer CS15, Acrylic Sealer CS15 and CS20 are designed to be used as a cure and seal compound on interior or exterior concrete surfaces.

Concretech CS Series Sealers VOC 400 are also available in all solids content for use as a Cure and Seal.

PACKAGINGCS Series Sealers are ready to use and are available in 3.78 L. /1 Gal., 18.9 L. /5 Gal. and 207.9 L. /55 Gal. containers. (Special orders only on the 55 Gallons.)

LIMITATIONSStandard Use:Do not apply when temperature is below 7C/45F or above 22C/72F. Surface must be clean, free of contaminates, oil, dirt, grease, mildew and moss. Take caution when using during windy conditions or where rapid air movement exists. Do not apply when rain or inclement weather is anticipated in the first 12 hours after application. Surface must be dry before applying any sealer.

Premium Use:Do not apply when temperature is below 7 C/45 F or above 29 C/84F. Precaution should be taken to condition materials in hot and windy conditions.

INSTALLATION INSTRUCTIONSProtect all surfaces that are not intended to receive sealer. Protect vegetation and landscaping. Clean all surfaces by scrubbing or pressure washing and rinse clean. Finish all touch up work, detailing, cleaning and surface coloration. Apply Concretech CS Series Sealers with pump up airless sprayer and back roll to establish continuous membrane. Apply at least two coats of CS25 or CS30. Surface must be touch-dry before applying second coat. Do not leave excess sealer in joints, grout lines or low spots. Contractors must use a sprayer designed for use with solvents. Other equipment may explode or fail, resulting in harm to persons or surrounding surfaces. All colored and imprinted concrete

surfaces shall have a sealer or water repellent coating applied to protect the finish from moisture and oxidization. Apply Concretech Cure and Seal (CS15) to freshly laid concrete as soon as possible. Follow up with Concretech High Solids Sealer (CS25 or CS30) after 28 days.

STORAGEStore away from heat source, open flame or spark. CS Series Sealers are flammable. Store in cool dry area out of direct sunlight. Shelf life under normal conditions is two years. Store in sealed containers ventilated areas only. Prevent contact with all sources of ignition, heat, spark and electric tools. Caution Flammable! Wear protective clothing, rubber gloves and eye protection. Prolonged exposure may result in respiratory illness, dizziness or damage to the nervous system. Contractor shall abide by all agency regulations for application, use, storage and disposal of solvent based materials. Keep away from children.

PROPERTIESColor ClearDry Time 1-2 Hours @ 21C (70F)Coverage:VOC CS15 Apply at 225 sqft/galVOC CS20 Apply at 250 sqft/galVOC CS25 Apply at 275 sqft/galVOC CS30 Apply at 275 sqft/gal

Concretech CS Series Sealers are available in VOC Compliant formulation for all states and In Canada. For regulations below 400 g/L of VOC, Concretech CS Series Sealers are available in Premium Use and Standard Uses formulation. Premium Use grade CS Series Sealer provide longer working time and delayed evaporation rates to allow contractors maximum ease of application.



CS Series SealersVOC 400

PRODUCT DESCRIPTIONConcretech CS Series Sealers VOC 400 are quality, abrasion resistant, durable, solvent base acrylic sealers for concrete protection and highlighting color.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESIt can be used as a thinner in most alkyd and acrylic industrial enamels and primers.

PACKAGINGAcrylithin is available in 3.78 L. / 1 Gal. and 18.9 L. / 5 Gal. containers.

LIMITATIONSContains VOC’s

INSTALLATION INSTRUCTIONSAlways start with a little amount, make sure it is dissolving in the paint, sealer or primer. Add more if necessary 5 to 15% by volume should be enough to obtain desired viscosity.

STORAGE AND HANDLINGStore in cool dry area away from open flame and spark. Caution: Flammable. Contact may cause severe burns. Avoid breathing vapors. Avoid eye contact. Wear protective clothing, vapor mask & eye protection. Use only in well ventilated areas. If swallowed call physician immediately. Contains Xylene. Keep away from children. See MSDS for additional information. Unusual fire and explosion hazards: Closed containers may rupture when exposed to extreme heat. Vapors may form an explosive mixture in the air.


Acrylithin

PRODUCT DESCRIPTIONAcrylithin is an aromatic petroleum distillate thinner. Acrylithin has a slower evaporation rate, but similar reducing power to #1 type thinners. It is not usually recommended for use in slow dry coating systems that require aliphatic thinners such as paint thinner or mineral spirits, due to some incompatibilities. Be sure to check with their particular product data sheets before adding.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESFor water repellant on porous masonry surfaces such as concrete that has not been hard trowelled or “burned”, manufactured stone, porous tiles such as Saltillo, porous brick such as old used brick.

PACKAGING5 US Gallon (18.9 Litre pail)

LIMITATIONSDo not freeze.

INSTALLATION INSTRUCTIONSMix concentrate with 3 additional parts clean water and apply with a low pressure sprayer. May be applied with brush or roller. Avoid excess application and runoff. Clean-up with water. Do not apply below 50 F (10 C). Do not freeze.

CURING: Allow to dry for 12 hours or more.

SEALING: Do not apply membrane forming sealers over AquaShed.Keep out of reach and inaccessible to children in a cool dry place away from sunlight.

STORAGEDO NOT ALLOW TO FREEZE.

APPEARANCEWhite, milk like, odorless, water borne liquid.

PROPERTIESMIXING: AquaShed is a concentrate. Mix container with 3 additional parts of clean water. For example: 1 quart AquaShed yields 1 gallon application material.

COVERAGE: Depends on porosity of substrate. Estimate from 200 to 400 square feet coverate per gallon mixed material. A very porous surface may profit by two applications within a few hours of each other.

SUBSTRATE: Plaster, stucco, concrete, brick, tile, manufactured stone, pavers and concrete. Surface must be wettable with water to accept AquaShed.

Weight Gain Reduction >80%Chloride Ion Reduction >80%Meets NCHRP 244, ASTM C-672 AASHTO - 259/260 salt ponding.

SAFETY PRECAUTIONSIrritation to the eyes and skin. Do not ingest. Wear latex gloves. Use eye protection. Keep containers closed and away from children. Keep containers closed.


AquaShed Penetrating Sealer

PRODUCT DESCRIPTIONAquashed is penetrating reactive water repellent coating that creates a hydrophobic surface. The aquashed material penetrates the surfaces and reacts to create a water repellent surface. Aquashed will not shift or discolor the surface.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESCure & Seal – Water Base may be used for: Dust proofing plant floors, walks, driveways, oil proofing concrete storage tanks for mineral and vegetable oils, floors, driveways, service station areas, lubricating areas, concrete walls, storage tanks, concrete blocks, cement asbestos pipes.

PACKAGINGCure & Seal – Water Base is available in 18.9 L. / 5 Gal. plastic containers.

LIMITATIONSAll membrane curing compounds and bond breakers must be removed to ensure penetration and maximum chemical resistance. Apply when concrete temperatures are above 5ºC (40ºF) and rising. Concrete must be free of contaminants, dry and structurally sound. Remove all surface laitance . Two thin coats produce better film protection than one thick coat. For other methods please contact Concretech Technical. Services. Avoid ponding. Cure & Seal – Water Base should not be applied to any surface that has already been treated with compounds that might prevent penetration (e.g. paint, oil).

INSTALLATION INSTRUCTIONSThe concrete surface should be wetted and scrubbed with soap or other cleaning compounds. The abrasive action removes the film of consolidated dirt and exposes the true wearing surface. The surface should then be scrubbed again with soapy water. To get the best penetration the floor should be allowed to dry for a minimum of 24 hours, depending on atmosphere humidity. Do not dilute Cure & Seal –Water Base, use it as it is. Each gallon covers 400 square feet of concrete with one coat. Cure & Seal may be applied with a brush, squeegee, low-pressure sprayer, or scrubbing machine.

STORAGEStorage: Shelf life is one-year from date of manufacture in protectedarea at 5° - 30° C.

PROPERTIESPhysical Properties (7 day cure @ 21°C (70°F)Abrasion Resistant ASTM C 418 - 0.3Freeze-Thaw Average Expansion ASTM C666 - 0.03Concrete Surface Compression Strength + 15%VOC g/L Excluding Volume of Water 7.0Efflorescence Resistance ExcellentIntercoat Adhesion ExcellentChemical Resistance (3 hour spot tests, covered) @ Room Temp.Acetic Acid<10% GAcid Waters<6.5 VGBoric Acid FChromic Acid 5% GFormic Acid 10% PHydrochloric Acid 10% VGPhosphoric Acid 10% VGTannic Acid GPetroleum Oil VGVegetable Oil VGFats and Fatty Acids ECoal Tar Distillates GEthyl Alcohol FAcetone PGlycerin VGEthylene Glycol G E=Excellent, VG=Very Good, G=Good, F=Fair, P=Poor SAFETY PRECAUTIONSHandling: Use appropriate respirator and protect skin and eyes from contact when using this product.Wear protective clothing, vapor mask & eye protection. Keep away from children. See MSDS for additional information.


Cure & Seal – Water Base

PRODUCT DESCRIPTIONCure & Seal – Water Base is a unique one-component water/base, odorless, non-flammable concrete sealer, and hardener. It has very good water resistant, and penetrating concrete binding properties. When applied to concrete Cure & Seal reduces porosity and permeability of the concrete matrix. This serves to increase the hardness and chemical resistance, which in turn, increases abrasion resistance and service life of the surface. Cure & Seal – Water Base is a low cost concrete treatment. It is easy to apply. It also complies with environmental, health and safety regulations.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESAcrylic Waterbase Sealer is recommended for exterior and interior applications. It is specially used where humidity and rain are a main concern.

BENEFITS High Gloss Rapid Drying UV Resistant Abrasion Resistant Wet Adhesion Good Adhesion to Chalky Concrete Easy to Apply Excellent Efflorescence Resistance

PACKAGINGAcrylic Waterbase Sealer is available in 18.9L. / 5 Gal. Plastic Containers

LIMITATIONSInspect all surfaces to ensure that they are sound, free of sealer, wax or oil. Surface preparation is the most important aspect in obtaining desirable results. Remove loose materials from the surface. Existing concrete surfaces should be scrubbed with a commercial degreaser (Concretech R/A Soap) using a red or black buffer pad on a commercial floor maintainer. Dispose the wash-offs in accordance with federal, state, and local regulations. Do not apply at temperatures below 10°C (50°F)

INSTALLATION INSTRUCTIONSSurfaces should be clean, dry and sound. Remove surface laitance. Application can be done with spray, short knap roller, squeegee or brush. May be thinned up to 5% with water if required. Two thin coats are better than one thick coat. First coat should touch dry and

clear before applying second coat. The surface needs light sanding if recoated after 24 hours. Damp concrete floors will get wet faster and achieve better adhesion.

STORAGE AND HANDLINGStorage: Shelf life of one-year from date of manufacture in protected area at 5ºC - 30ºC (40-85ºF). Store in a dry place.

Handling: Avoid prolonged or repeated skin contact. Wash hands thoroughly after handling and before eating or drinking. Keep away from children. See MSDS for additional information.

PROPERTIESAnalysisNon Volatile (Wt) 30 %Non Volatile (Vol) 27.3 %Specific Gravity 1.037g./m³VOC, lbs/gal 0.21VOC, g/l 25Dry Time @ 25°C (77°F)Tack Free ½ HourThorough Dry 1 HourHard Dry 24 Hours

Coverage is 400 SqFt. / 3.78 L. (1 Gal.)2000 SqFt. / 18.9 L. (5 Gal.)


Acrylic Waterbase Sealer

PRODUCT DESCRIPTIONAcrylic Waterbase Sealer is a high performance 100% Acrylic finish coat. A 4-mil (wet) coat will provide transparent, high gloss, abrasion resistant finish with minimum surface preparation.

Concrete Chemical Technologies104, 2567 192 StreetSurrey, BC V3S 3X1www.concretechproducts.com

Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESPA-30 is used as a finish coat for Concretech UB-680 multi-coat epoxy commercial and industrial coating applications. PA-30 is also used for top coat of multi coat, colored, vinyl chip coating systems. PA-30 is designed as a single or multi coat clear sealer for acid stained and decorative concrete finishes. PA-30 can be used in both interior and exterior applications.

PACKAGINGAvailable in one gallon kits consisting of Part A - 2.85 litres and Part B - 1.04 litres. There is sufficient head space in the Part A container to allow for mixing of the material.

LIMITATIONSDo not apply PA-30 when water vapor transmission (vapor drive) exceeds three pounds per 1,000 square feet per twenty-four hours. Do not apply to concrete that has excessive moisture. Allow concrete to cure a minimum of seven days before applying PA-30.

INSTALLATION INSTRUCTIONSConcrete shall be fully cured. Ensure vapor drive and concrete moisture limits are adhered to.

Surface Preparation Remove all dirts and contaminants. Ensure no sealers or membrane forming curing agents are present on the surface. Concrete must be sound and free of defects. Best surface is achieved by mechanical abrasion using grinding machines with diamond heads achieving a 50-100 grit profile.

Application Mix the entire contents of Part A&B by gentle stirring. Avoid over mixing and high speed mixing to avoid introducing moisture or air. No induction time is required prior to applying PA-30.

Apply by roller using a 1/8” - 3/8” synthetic nap roller. PA-30 may be re-coated after three hours and not more then 48 hours after each coat.

Use Xylene or Acetone to clean tools.

STORAGEShelf life is one year when stored unopened between 8 C (40 F) and 35 C (95F) out of direct sun light.

PROPERTIESVOC <400 grams/litrePot Life 30 minutesOpen to traffic Light - 4 hours, Vehicular - 24 hoursSolids (Mixed Part A & B) 72%Minimum Re-Coat time - 3 hoursMaximum Re-Coat time - 48 hours

Coverage 500 sqft/gal @ 3mils 400 sqft/gal @ 4 mils 320 sqft/gal @ 5 mils

ADVANTAGESSuperior bond strengthExcellent abrasion resistanceCan be used as single coat sealant or in multiple coatsCan be used as top coat to Ultrabond 680 coating systems30 minute pot lifeCan be opened to traffic within 24 hours.3 hour re-coat time.Excellent chemical resistanceResists hot tire pick up


PA - 30 VOC 400Polyaspartic Polyurea

PRODUCT DESCRIPTIONPolyaspartic 30 (PA-30) is a fast-curing sealer with a 30 minute pot life for use as a sealant or protective finish for concrete and decorative coating systems. PA-30 is ideal as a top coat for Concretech Ultrabond 680 (UB-680) epoxy or to protect acid stained, dyed or decorative concrete finishes. PA-30 dries quickly and can be opened to vehicular traffic within 24 hours. PA-30 has superior abrasion, impact and chemical resistance. PA-30 is applied by roller or brush in single or multiple coats depending on the intended application.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


ADVANTAGESWater clear high gloss finish Long pot life, rapid dryingTenacious BondOdor-freeExtremely good abrasion resistance

USESDecaThane 200 is a high performance sealer for industrial/commercial finishing applications. A 5-mil (wet) coat will optimize bond with the concrete surface and create a coating with excellent chemical resistance. DecaThane 200 can also be used on commercial and residential concrete floors because of its high stain resistance and flexibility while maintaining film hardness.

PACKAGINGDecaThane 200 part A 2.838 L. / 0.75 Gal.DecaThane 200 part B 0.946 L. / 0.25 Gal.DecaThane 200 Mixture 3.78 L. / 1 Gal. kits

LIMITATIONSDecaThane 200 is a high performance coating and must be installed by persons familiar with coating systems. Test compatibility with substrates prior to application. Use caution when sealing over acid stained floors to ensure that acid/salts are fully neutralized.

INSTALLATION INSTRUCTIONSConcrete should have achieved full cure. Surfaces must be clean, dry and sound. Remove surface laitance. Pour part B into part A under agitation and mix until a uniform white paste is obtained. Always maintain 3A:1B by volume ratio when mixing part batches. The pot lifeof the mixed product is 1.0 hour at 20ºC (70 ºF). After 1.0 hour the mixture may look unchanged but the components have already reactedand will not form a high quality film. High temperature and larger batches will reduce the pot life. Do not re-seal any container that has mixed sealer, as CO2 gas will generate creating pressure in the container. For best application, flow and penetration DecaThane 200 should be diluted with water after thorough mixing of, part A and part B. One (1.0) part by volume of water can be added and mixed to one (1.0) part by volume of A+B mixture. Always apply a test patch prior to installation to rule out incompatibility, adhesion and application issues. Best adhesion is obtained by applying DecaThane 200 in two coats, primer and topcoat layers. The primer can be made by mixing 5.0 parts(by volume) A with 1.0 part (by volume) B, mix to a uniform paste and then dilute with 3.0 parts by volume of water. Always maintain 3 to 1 by volume for the topcoat and 5 to 1 by volume ratio for the primer. DecaThane 200 may be applied by brush; roller or sprayer at recommended film thickness of 5.0 mils wet and about 1 mil dry. One gallon diluted DecaThane 200 will cover 480 to 640 sqft depending on surface porosity. Allow 1.5 hours to tack free at 20°C (70 ºF). Open to light foot traffic at 8 hours and open to heavy traffic in 3 days. The floor may be recoated or top coated after 2-4 hours.

STORAGEStorage: Shelf life @ 20°C (70°F) is six months from date of manufacture provided that both components are kept in their original containers and unopened.

PROPERTIESAnalysis

Non Volatile (Wt) >45 %

Non Volatile (Vol) >41 %

Specific Gravity 1.073

VOC, lbs/gal ~ 0

VOC, g/l ~ 0

Dry Time

Tack Free Time 1.5 Hours

Thorough Dry 8 Hours

Hard Dry 20 Hours

Pendulum Hardness And Gloss

2 Week Cure 108 Seconds

20 Degree 80

60 Degree 95

Physical Properties (7 day cure @ 25°C(77 ºF))

Taber Abrasion CS-17 Wheel,1000 g Load 1000 Cycles

39 mg. Loss

Impact, Direct 160 lbs

Impact, Reverse 160 lbs

Conical Mandrel Pass

MEK Double Rubs 100+

Chemical Resistance (3 hour spot tests, covered)

Acetone 4

Xylene 5

10% Acetic Acid 5

2% Nitric Acid 5

Chemical Resistance (3 hour spot tests, covered) Cont:

10% HCl 5

Methanol 5

10% Sulfuric Acid 5

Isopropanol 5

DecaThane 200

PRODUCT DESCRIPTIONDecaThane 200 is a superior performance zero VOC urethane sealer. DecaThane 200 is clear, water based, deep penetrating, and fast drying. DecaThane 200 is safe to handle and work with. DecaThane 200 cures to a water clear, high gloss finish.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

Gasoline 4

Skydrol LD-4 5

1:1 Ethanol/Water 5

Ethanol 5

5 = No Effect, 1 = Destroyed

SAFETY PRECAUTIONSHandling: Prolonged contact of component A with skin may cause irritation. Vapor and spray mist are harmful. Use appropriate respirator and protect skin and eyes from contact when using this product. Component B is an irritant. Contact may cause severe burns. Avoid breathing vapors. Avoid eye contact. Wear protective clothing, vapor mask & eye protection. Keep away from children. See MSDS for additional information.



DecaThane 200Pg. 2



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

ADVANTAGESWater Clear High Gloss FinishNon-YellowingRapid DryingExcellent AdhesionExceptional Surface HardnessExcellent Impact and Abrasion Resistance

USESDecaThane 230 is an ideal sealer for commercial, industrial and residential floorings such as Seamless Flooring, Hardwood Floor Coating, Concrete Floor Coating and Dust Proofing. DecaThane 230 can also be used as an aggregate binder.

PACKAGINGDecaThane 230 is available in 3.78L./1 Gal. and 18.9L./5 Gal. containers.

LIMITATIONSDecaThane 230 should not be applied at temperatures below 50º F (10ºC). The product contains aromatic solvents that evaporate during its curing process. This solvent should be dispersed from the area by adequate ventilation.

INSTALLATION INSTRUCTIONSConcrete should have achieved full cure: normally 28 days. Surfaces should be clean, dry and sound. Remove surface laitance. Application can be done with spray, short knap roller, or brush. For the best results, the sealer should be poured or flowed over the surface, taking care to minimize air entrapment. Damp surfaces should be primed with 27% solid coat to tie up surface moisture and prevent bubbling in subsequent coats. To make a sealer with 27% solid, mix one part by volume of DecaThane 230 with one part by volume of Acrythin. Wood surface must be clean, dry, and free from grease, oil or other foreign matter. Apply the sealer with a good quality applicator. Any number of successive coats of DecaThane 230 can be applied provided 24 hours have not transpired since the previous application. One gallon of DecaThane 230 on smooth non-porous surfaces covers up to 860 SqFt. obtaining 1 mil dry film thickness. If the product is thinned to be applied as a primer then one gallon of the thinned product will cover 430 SqFt.

STORAGEStorage: Shelf life of four months from the date of manufacture in protected area at 5 - 30ºC.

PROPERTIESAnalysis

Non Volatile (Wt) 59.0%

Non Volatile (Vol) 54.0%


VOC, lbs/gal 3.38

VOC, g/l <400

Dry Time

Tack Free Time 1 to 24 Hours at 23°C


Hard Dry 24 Hours

Sward Hardness

1 Day 25

3 Days 38

7 Days 38

Physical Properties (7 day cure @ 25°C)

Pencil Hardness HB





DecaThane 230

PRODUCT DESCRIPTIONDecaThane 230 is an Oil-free, single component MOSITURE CURE aliphatic polyurethane sealer. It is clear, low viscosity, solvent based, designed as a fast drying protective coating on substrates such as concrete metal and wood. DecaThane 230 dries by a combination of solvent release, and polymerization initiated by both moisture in the atmosphere and of catalyst.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

Chemical Resistance (Immersion Test 7 Days @ 125°F(Volume Increase or swelling)

Kerosene 0( no effect)

Xylene 30

High Flash Naphtha 25

Methylene Chloride 50

MEK 40

Ethyl Alcohol 55

Ethylene Glycol 10

Vegetable Oïl 0( no effect)

Ethyl Acétate 75

Glycerin 0( no effect)

1:1 Ethanol/Water 30

MIBK 55

Kerosene 0( no effect)

Coverage: 430 SqFt. / 2mil/Gal

SAFETY PRECAUTIONSHandling: Prolonged contact with skin may cause irritation. Vapor and spray mist are harmful. Use appropriate respirator and protect skin and eyes from contact when using this product.Avoid breathing vapors. Avoid eye contact. Wear protective clothing, vapor mask & eye protection. Keep away from children. See MSDS for additional information.



DecaThane 230Pg. 2



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

USESDecaThane 250 is an ideal topcoat for epoxy and concrete. A 5-mil (wet) coat will provide a tough, abrasion resistant finish. Top coat over water based epoxy, exposed aggregate, terrazzo or acid stained concrete and light traffic warehousing areas.

PACKAGINGDecaThane 250 is available in 18.9 L. / 5 Gal. pails.

LIMITATIONSHeavy vehicular traffic (unless crosslinked)

INSTALLATION INSTRUCTIONSConcrete should have achieved full cure: normally 28 days. Surfaces should be clean, dry and sound. Remove surface laitance. An absorbing concrete surface may be wetted for better adhesion.

Application can be done with spray, short knap roller, squeegee or brush. May be thinned up to 5% with water if required. For maximum performance add DecaThane 250 Crosslinker before use.

STORAGEStorage: Shelf life of one year from date of manufacture in protected area at 0-40°C (32-104°F).

PROPERTIESAnalysis


Non Volatile (Vol) 23%


VOC, lbs/gal 0.77

VOC, g/l 93

Dry Time

Tack Free Time 1/2 Hours


Hard Dry 3 Hours



96 mg.



Conical Mandrel Pass Elongation, % 160

Pencil Hardness H-2H


MEK Double Rubs +100

Xylene 5

Toluene 5

Methanol 5

10% Acetic Acid 5

10% HCl 5

Isopropanol 5

Ethanol 5

Gasoline 5

Vodka 5

Ketchup 5

Hot Coffee 5

Lipstick 5

Mustard 5


With addition of crosslinking Agent5=No effect, 1= Destroyed

Square Footage 320 SqFt. per Gal. Depending on porosity

SAFETY PRECAUTIONSProlonged contact with skin may cause irritation. Vapor and spray mist are harmful. Use appropriate respirator and protect skin and eyes from contact when using this product. DecaThane 250 Crosslinker is an irritant. Contact may cause severe burns. Avoid breathing vapors. Avoid eye contact. Wear protective clothing, vapor mask & eye protection. Keep away from children. See MSDS for additional information


DecaThane 250

PRODUCT DESCRIPTIONDecaThane 250 is a one component water based sealer. It cures to a tough, abrasion resistant, non-yellowing high gloss finish. It is low odor, rapid drying and UV resistant.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESDecaThane 450 is an ideal top coat for metal and concrete substrates, where appearance and durability are important. DecaThane 450 is ideal for showroom floors, shopping mall floors, sport complexes, chemical plants, shower walls and floors, pool decks, warehouse walls and floors.

It can be sprayed or rolled. On concrete, best performance is obtained if Ultrabond 400 VOC400 is used as a primer.

PACKAGINGOne Gallon Unit, Part A+ Part B = 3.000 Kg + 0.820 KgThree Gallon Unit, Part A + Part B = 9.000 Kg + 2.450 Kg

INSTALLATION INSTRUCTIONS

PROPERTIESSolid Content 60.0% by Weight

NOC/OH 1.10/ 1.00

VOC 399 g/L

Specific Gravity (Theoretical) 1.005 g/cm3

Part A/Part B 4.0/1.0 by Volume

Pot Life 1.5 Hour @21C

Surface Dry 3.5 Hours@ 21C

Coverage = between 200 to 300 sft / Gallon

Hardening Time 3.0 Days, Mechanical

Gloss (On smooth dense concrete like SLO)

Flat 300 sft/Gallon

Glossy 170 sft/Gallon

Resistant

Full Cure 7.0 Days, Chemical Resistant

Pencil Hardness H

Flexibility Very Good

MEK Double Rub 100+

Impact Resistance VG

Conical Mandrel VG


DecaThane 450 VOC4002 Part Solvent Based Urethane

PRODUCT DESCRIPTIONDecathane 450 VOC 400 is two component solvent based urethane concrete clear sealer, two -component and can be used both as primer and top coat. It shows very good UV resistance and abrasion resistance and high gloss and gloss retention. DecaThane 450 resists hot tire stain, is non -yellowing and highly chemical resistant.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147




Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147

Concretech Inc.’s sole warranty is that our products have been manufactured to meet with our written specifications. The information herein is general information to as-sist our customers in determining whether our products are suitable for their applications. Our products are intended for sale to commercial and industrial custom-ers. We require customers to inspect and test our products before use and to satisfy themselves as to contents, suitability and applications. Nothing herein shall constitute any other warranty, express or implied, including any warranty of merchantability or fitness for a particular purpose, nor is any protection from any law or patent inferred. All patent and trademark rights are reserved. The exclusive remedy for all proven claims is placement of our materials and in no event shall we be liable for incidental or consequential damages.

DecaThane 450 VOC400Pg. 2

USESUltraBond 400 is an ideal primer for epoxy and urethane topcoats. A 5-mil (wet) coat will optimize bond, retard out-gassing and enhance the self-leveling properties of a polymer topcoat.

PACKAGING15.12 L. / 4 Gal. Part A}3.78 L. / 1 Gal. Part B } 18.9 Litres

INSTALLATION INSTRUCTIONSConcrete should have achieved full cure: normally 28 days. Surfaces should be clean, dry and sound. Remove surface laitance. Mix all of part B into all of part A. Mix with adequate drill mixer until thoroughly mixed, usually 1-2 minutes. Let mixed material stand (induct) for 10 minutes. Always maintain 4A:1B ratio when mixing part batches. Do not add solvents or other thinners. Application can be done with spray, short knap roller, squeegee or brush. In primer applications a 5-mil (wet) coat is adequate. Do not allow the product to pond. Pot life of mixed product is 8 hours.

STORAGEStorage: Shelf life of one year from date of manufacture in protected area at 5-40°C (40-104°F).

PROPERTIESAnalysis for A-B Mixture

Non Volatile (Wt) 46.0 %

Non Volatile (Vol) 38.1 %


VOC, lbs/gal 4.3

VOC, g/l 517

Dry Time @ 25°C (77°F)


Hard Dry 12 Hours

Sward Hardness

1 day 14

3 days 24

7 days 26

Physical Properties (7 day cure @ 25°C (70°F)

Pencil Hardness no data

Impact, Direct 140

Impact, Reverse 120




Acetone 4

Xylene 5

10% Acetic Acid 5

2% Nitric Acid 5

10% HCl 5

Methanol 5

10% Sulfuric Acid 5

Isopropanol 5

Gasoline 4

Skydrol LD-4 5

1:1 Ethanol/Water 5

Ethanol 5

5 = No Effect, 1 = Destroyed

Square Footage 320-500 SqFt. / 3.78 L. / 1 Gal.(Depending on Surface Porosity.)

SAFETY PRECAUTIONSHandling: Prolonged contact of component A with skin may cause irritation. Vapor and spray mist are harmful. Use appropriate respiratorand protect skin and eyes from contact when using this product. Component B is an irritant. Contact may cause severe burns. Avoid breathing vapors. Avoid eye contact. Wear protective clothing, vapor mask & eye protection. Keep away from children. See MSDS for additional information.


Ultrabond 400

PRODUCT DESCRIPTIONUltraBond 400 is a clear, low viscosity, solvent based, deep penetrating and fast drying epoxy primer. Ultrabond 400 cures to a water clear, high gloss finish, provides tenacious bond and is economical.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESUltraBond 680 is very resistant to a wide range of chemicals and performs extremely well under abrasive and high impact conditions. UltraBond 680 adheres tenaciously to both concrete and steel. Spectacular results can be obtained where dramatic visual impact is desired: showrooms, airport hangers, factories, pulp mills, chemical plants, agriculture and food preparation, containment areas.

PACKAGINGUltraBond 680 is available in virtually any color.Ultrabond 680 Part A is 7.56 L. / 2 Gal.Ultrabond 680 Part B is 3.78 L. / 1 Gal.Ultrabond 680 Part A+B 11.34 L. / 3 Gal. Kits.

LIMITATIONSConcrete must be free of contaminants, dry and structurally sound. Preferred method is by shot blasting. For other methods please contact Concretech Technical Services. In severe service and retrofit applications, prime floor with UltraBond 400. Chase non-moving cracks and fill with Expoy repair. For larger spalls produce a blend of UltraBond 680 and specific grades of silica. A very limited number of cementitious grouts are suitable on larger patches. Contact Concretech Technical Services for details and technical bulletins on any of the above products. Steel should be clean to white metal, but in most cases a commercial blast is adequate. The minimum profile expected on steel is 1 mil.

INSTALLATION INSTRUCTIONSPre-mix Part A, taking care to scrape the sides of pail with a paint stick. Then add Part B and mix for 2 min. Mix only amount that can be used within the 30 min pot life and maintain the 2A:1B ratio by volume. No induction time necessary. Do not add thinners. Do not apply UltraBond680 on damp surfaces (prime with UltraBbond 400 first) or at temperatures below 5°C (40°F). The product does not blush and can be re-coated anytime. A light sanding is required if floor has been in service. If floor is primed with UltraBond 400 or with thicker overlays, out-gassing is not a problem. UltraBond 680 flows out very well. With thin overlays and applicators unfamiliar with UltraBond 680, apply a thin prime coat and allow out gassing to dissipate: then recoat. At 20°C(68°F), UltraBond 680 can be re-coated and/or ready for foot traffic overnight. UltraBond 680 is ideal for high build, vertical and anti skid applications.

STORAGEShelf life of one year from date of manufacture in protected area at 5-40°C (40-104°F).


Non Volatile (Wt) 98.7 %

Non Volatile (Vol) 98.5 %


Bond Strength to Damp Concrete, psi

Cure at 23 C 604

Cure at 4.4 C 542

Abrasion Resistance (CS-10/1000g)

39 mg loss

Physical Properties (7 day cure @ 25°C (70°F)

Compressive Strength, psi 0

Compressive Modulus, x1000 psi

340

Tensile Strength, psi 10,100

Tensile Modulus, x1000 psi 449

Elongation, % 4.2

Flexural Strength, psi 15,900

Flexural Modulus, x1000psi 545

Tg C 57


Skydrol 500-B E

Xylene VG

10% Acetic Acid G

2% Nitric Acid VG

10% HCl E

Bleach E

Methanol P

10% Lactic Acid E

70% Sulfuric Acid E

98% Sulfuric Acid P

Ultrabond 680

PRODUCT DESCRIPTIONUltraBond 680 is a premium, versatile, two component, 100% solids, VOC compliant, self-leveling epoxy. UltraBond 680 combines chemical resistance, toughness and tenacious bond strength with a bright, aesthetically pleasing finish. The product is approved by the Hygienic Environment, Food Inspection Branch of the Federal Government for use in Registered Environments.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


50% Sodium Hydroxide E

10% Ammonium Hyd. VG

Water E

Ethanol F

Butyl Cellosolve G

E=Excellent, VG=Very Good, G=Good, F=Fair, P=Poor

Square Footage 160 SqFt. per 3.78 L. at 10 mils thickness.





Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


Ultrabond 680Pg. 2

ADVANTAGES• high chemical resistance• very abrasion resistant• ease of application• high penetration to concrete• applicable to wet concrete• breathable• solves water vapor transmissions problems• fast drying and high gloss

USESUltrBond 803 is used on floors, structures and facades. It spreads easily and produces a uniform glossy look. It can be top coated with DecaThane 200 for better abrasion resistance. Once the primer’s appearance turns from cloudy to clear, a waterborne DecaThane 200 topcoat can be applied.

PACKAGINGUltraBond 803 Part A in 11.35 L. / 3 Gal.UltraBond 803 Part B in 3.78 L. / 1 Gal.UltraBond 803 A+B Mixture 15.12 L. / 4 Gal. per unit.

INSTALLATION INSTRUCTIONSSurface should be clean and free from any contamination. For better penetration and adhesion the concrete may be sanded. Substrate temperature should not be below 12°C (54°F) and relative humidity not above 80%. Mix 3.0 parts by volume of Part A with 1.0 part by volume of part B. Use adequate drill mixer and paddle to achieve consistent mix. Allow 5.0 minutes induction time. The pot life for A and B mix is about 4.0 hours at 20°C (68°F). After 4.0 hours the mixture may look unchanged but cannot be used. Wet theoretical coverage is 400 SqFt. per gallon per 4.0 mils thick coat. Apply with roller, brush or spray at approximately 4.0 mils per coat. UltraBond 803 can be recoated after it turns clear. Recoating has to be within 24 hours under normal curing condition. If the sealer is allowed to cure longer than 24 hours, sanding will be necessary. Do not thin with water.

STORAGEStorage: Shelf life of one-year from date of manufacture in protected area at 5-30°C (41- 86ºF).




Non Volatile (Vol) 32.0%


VOC, lbs/gal 0.48

VOC, g/l 58

Dry Time @ 25°C (77 ºF) / hours

Tack Free Time 1.5 Hours

Thorough Dry 2.5

Hard Dry 4.0


Pencil Hardness 4 H


164 mg loss




Gloss (60/20) 92/82


Chemical Resistance (7 day cure @ 25°C (77°F))

10% HCl 6F Blisters

10% Acetic Acid Film Destroyed

10% Ammonia No Effect

10% Sulfuric Acid 8MD Blisters

Water No Effect

Ethanol Loss of Gloss

Gasoline No Effect

15% Sodium Hydroxide No Effect

Square footage is 400 SqFt. / 3.78 L. / 1 Gal.


Ultrabond 803

PRODUCT DESCRIPTIONUltraBond 803 is a two-component water base epoxy used where high penetration, adhesion and breathability is the required. UltraBond 803 is formulated to have exceptional resistance to corrosive chemicals and staining. UltraBond 803 Primer / Sealer can be applied directly to wet 4 hour pour concrete with no loss of adhesion.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESWB Cure is used to chemically cure concrete immediately after finishing operations. WB Cure is economical and is used for curing both interior and exterior concrete structures. WB Cure is available with a green fugitive dye to assist applicators in achieving specified rates of application.

PACKAGINGAvailable in 18.9 Litre (5 Gallon) pails and 205 Litre (45 Gallon) drums.

LIMITATIONSWB Cure is a chemical curing compound and will dissipate under normal conditions. WB Cure IS NOT A SEALER OR COATING.

INSTALLATION INSTRUCTIONSConcrete should be clean and free of all laitance, oil, grease and other foreign substance. Concrete should be free of all standing water prior to applying WB Cure.

Cast, consolidate, level and finish concrete to specification.

Immediately after finishing operations and disappearance of the surface sheen apply WB Cure.

Apply WB Cure by airless sprayer or roller.

SAFETY PRECAUTIONSVarious solvents contain chemicals known to be embryonic toxicants. Consult MSDS for further information.

PROPERTIES• Economical• Non-Yellowing • Versatile• Will not blush• Superior bonding characteristics• Fast Drying

Appearance: Milky white Viscous LiquidYield: 300 square feet per gallon (7.34 square meters per litre)Shelf Life: Approximately 1 year when stored properlyDrying Time: Dries in ½ hour at 25 C

Applicable Standards: Meets or exceeds ASTM C309Density: 0.905 kilograms per litre (7.5 lbs. per gallon)


WB Cure Water-based curing compound

PRODUCT DESCRIPTIONWB Cure is an emulsion of hydrocarbon resin and aliphatic ketones. WB Cure prevents the rapid evaporation of gauging water that is critical to the proper hydration and strength development of concrete. WB Cure retains over 95% of mixing water for proper strength gain and concrete.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


USESConcretech WBW Cure is used to chemically cure concrete immediately after finishing operations. Concretech WBW Cure can be used on any concrete structure that may be exposed to light source that can cause uneven hydration of the concrete structure. Concretech WBW Cure is typically used in hot weather conditions on exterior slabs like walkways, curbs and gutters, concrete intersections, bridges and airport tarmacs. Concretech WBW Cure increases the durability of the concrete structure by minimizing the temperature differential between the surface and rest of the slab and by creating a continuous film that maintains the moisture in the concrete matrix that is critical for hydration.

PACKAGINGAvailable in 18.9 Litre (5 US Gallon) pails and 205 Litre (45 Imperial Gallon) drums.

LIMITATIONSDo not apply WBW Cure to base slabs that will have other flooring or coatings installed. Concretech Resin Cure is more appropriate for these applications.

INSTALLATION INSTRUCTIONSConcrete should be clean and free of all laitance, oil, grease and other foreign substance. Concrete should be free of all standing water prior to applying Concretech WBW Cure.

PROPERTIESAppearance: White LiquidYield: 200-300 square feet per gallonShelf Life: Approximately 1 year when stored properlyConcrete Curing Drying Time: Dries in ½ hour at 25 CApplicable Standards: Meets or exceeds ASTM C309Density: 0.895 kilograms per litre (7.3 lbs. Per gallon)Solids: 7%• Economical• Non-Yellowing• Will not plug or clog sprayer• Fast Drying

SAFETY PRECAUTIONSWBW Cure is formulated using solvent carriers. These solvent carriers are released to the atmosphere during the drying process and can accumulate in enclosed areas creating an ignition hazard. Adequate ventilation should be considered prior to applying WBW Cure in enclosed areas.. Various solvents contain chemicals known to be embryonic toxicants. Consult WBW Cure MSDS for further information.


WBW Cure White, water-based curing compound

PRODUCT DESCRIPTIONConcretech WBW Cure is an emulsion of aliphatic ketones, petroleum resin and water. Concretech WBW Cure is pigmented white and prevents the evaporation of gauging water that is critical to the proper hydration of concrete. Concretech WBW Cure is formulated for ease of application, can be sprayed or rolled and will not yellow when exposed to UV light sources.



Toll Free: 1.888.503.6780Fax: 1.604.357.1344Tel. 1.604.210.1147


technical data booklet

Documents