technical manual & parts lists€¦ · 15/3/2016 · 362 industrial park drive . atlanta...

Atlanta Attachment Company

362 Industrial Park Drive

Lawrenceville, GA 30046

770-963-7369 • www.atlatt.com

Technical Manual & Parts Lists

Model 1379D Revision 2.5 Updated Mar. 15, 2016


NOTICE CAUTION – use of controls or adjustments, or performance of procedures other than those contained in the operation, maintenance or any other manual provided with this machine may result in hazardous radiation exposure. This laser process machine is certified as a CLASS I laser product to the requirements of the US Federal Product Performance Standard for Laser Products contained in the regulations in 21 CFR Subchapter J except for deviations pursuant to specific FDA issues notices. Class I laser products are not considered to be hazardous This machine incorporates one or more Class 4 laser systems manufactured by Coherent, which, by themselves, may be hazardous. However, this process machine incorporates a protective housing, protective window filters, and safety interlocks in the machine design such that there is no exposure or human access to laser radiation during operation, maintenance or normal user service. UNDER NO CIRCUMSTANCE shall attempts be made by the user to operate the laser with safety interlocks overridden. Interlocks override is password protective and is to only be overridden by the manufacturer. Protective housing warning labels are affixed to specific portions of the protective housing to assist in providing warnings of the potential hazards if protective panels are removed or safety interlocks are overridden during the performance of the manufacture’s service procedures. It is strongly recommended that all service to the Coherent laser systems and their delivery optics requiring internal interlock bypass be performed by their manufacturer’s service personnel, their authorized agents, or personnel trained by their manufacturer. The laser should not be operated if any of the protective window material installed onto the protective housing is damaged or removed. The machine design is such that a direct exposure of the window material from laser radiation is not likely. The window material is constructed out of LEXAN, a polycarbonate material. Poly carbonate is commonly used within the industry to protect against CO2 wavelength and even very thin polycarbonate is known to have a minimum optical density (OD) of 4+ @ 10,600 nm. Contact the manufacturer for replacement information.


IMPORTANTIt is important to read and understand the information contained within this manual before attempting to operate the machine. Atlanta Attachment Co., Inc. shall not be held liable for damage resulting from misuse of the information presented within, and reserves the right to change the information contained within, without prior notification.

ATLANTA ATTACHMENT COMPANY, INC.

Confidential and Proprietary Information The materials contained herein are confidential and proprietary information of Atlanta Attachment Company. In addition to any confidentiality and non-disclosure obligations that currently exist between you and Atlanta Attachment Company, your use of these materials serves as an acknowledgment of the confidential and proprietary nature of these materials and your duty not to make any unauthorized use or disclosure of these materials. All materials contained herein are additionally protected by United States Copyright law and may not be used, disclosed, reproduced, distributed, published or sold without the express written consent of Atlanta Attachment Company, which consent may be withheld in Atlanta Attachment Company’s sole discretion. You may not alter or remove any copyright, trademark or other notice from copies of these materials.


Contents Important Safety Instruction ....................................................................................................................... 1

Liability ...................................................................................................................................................... 2

Safety Equipment on the Machines ............................................................................................................ 3

Protective Eyewear ..................................................................................................................................... 4

Important Notices........................................................................................................................................ 5

Maintenance ................................................................................................................................................ 7

Repair .......................................................................................................................................................... 8

A Word to the End User.............................................................................................................................. 9

Safety Precautions ....................................................................................................................................... 9

1.- MACHINE LAYOUT ......................................................................................................................... 10

1.1.- Machine Components ....................................................................................................................... 10

1.2.- Machine Layout ................................................................................................................................ 11

1.3.- Machine Material Thread-Up Diagrams ........................................................................................... 12

1.4.- Lockout/Tagout Program .................................................................................................................. 13

1.5.- Laser Output Characteristics ............................................................................................................ 14

1.6.- Laser Personal Protective Equipment ............................................................................................... 15

2.- MACHINE SETUP ............................................................................................................................. 16

2.1.- General Machine Data ...................................................................................................................... 16

2.2.- Optional Equipment & Accessories ................................................................................................. 16

2.2.1.- Optional Equipment:...................................................................................................................... 16

2.2.2.- Optional Accessories: .................................................................................................................... 17

E-Z Laser .................................................................................................................................................. 18

Definitions................................................................................................................................................. 19

Main Run Screen....................................................................................................................................... 21

Order Setup ............................................................................................................................................... 22

Command Buttons .................................................................................................................................... 23

Load Material ............................................................................................................................................ 25

Manual Operations .................................................................................................................................... 26

Style Screen .............................................................................................................................................. 30

Utilities ...................................................................................................................................................... 33

Settings ...................................................................................................................................................... 36

Technician Screen ..................................................................................................................................... 38

2.3.- Inverter Programming and Parameter Data ...................................................................................... 39

2.3.1. - Programming ACTech SCL/SCM Drive ...................................................................................... 39

2.3.2. - Infeed Pinch Roll Drive Motor Parameter Menu ......................................................................... 40

2.3.3. – (OPTIONAL) Rewinder Drive Motor Parameter Menu .............................................................. 42


Assembly Drawings & Parts Lists ............................................................................................................ 45

11379D Dual Head Laser Cutter, 55Watt ................................................................................................. 46

11379D100 Dual Head Laser Cutter, 100Watt ......................................................................................... 47

11379D150 Dual Head Laser Cutter, 150Watt ......................................................................................... 48

1379013 Laser Guard Assembly, 55 watt ................................................................................................. 49

1379006 Laser Guard Assembly, 100 watt ............................................................................................... 50

1379461 Laser Guard Assembly, 150 watt ............................................................................................... 51

1379153 Right Side Vent Hood Assembly ............................................................................................... 52

1379200 Generic Laser Workstation ........................................................................................................ 53

1379034 Keyboard Tray Assembly .......................................................................................................... 54

1379044 LCD Touchscreen Mount .......................................................................................................... 55

1379064 Laser Worktop Assembly .......................................................................................................... 56

1379101 Safety Switch Enclosure ............................................................................................................ 57

1379208 Front Guard Assembly ............................................................................................................... 58

1379266 Rear Guard Assembly ................................................................................................................ 59

1379457 Pneumatic Panel Assembly ........................................................................................................ 60

1379581 Valve Stack Assembly ............................................................................................................... 61

1379767 Material Edge Sensor Assembly ................................................................................................ 62

1379795 Stacker Festoon Assembly ......................................................................................................... 63

1379825 RH Stacker Rack Clamp ............................................................................................................ 65

1379830 LH Stacker Rack Clamp ............................................................................................................ 67

1379850 Laser Head Drive Assembly ...................................................................................................... 69

1379870 Laser Process Head, 55 Watt ..................................................................................................... 70

1379935 Stacker Safety Eye Assembly .................................................................................................... 71

1379860 Main Roller Assembly ............................................................................................................... 73

1379896 Control System Assembly.......................................................................................................... 75

1379071 Right Cloth Support Assembly .................................................................................................. 76

1379072 Left Cloth Support Assembly .................................................................................................... 77

1379224 Pinch Adjust Roller Assembly ................................................................................................... 78

1379534 Roller Lift Cylinder Assembly................................................................................................... 79

1379572 Y-Axis Motor Assembly ............................................................................................................ 80

1379766 Stacker Clamp Cylinder Assembly ............................................................................................ 81

1379883 Rear Feed Clutch Assembly ....................................................................................................... 82

1379211 Roll Mandrel Assembly, 1.5” core ............................................................................................ 83

1379212 Roll Mandrel Assembly, 3” core ............................................................................................... 84

1379234 Laser Sub Assembly, 55W ......................................................................................................... 85

1379878 Laser Sub Assembly, 100 Watt .................................................................................................. 87


1379492 Laser Sub Assembly, 150 Watt .................................................................................................. 89

1379498 Laser Cooling System Assembly, 150 Watt .............................................................................. 90

1379476 Filter Stand Assembly, 150 Watt ............................................................................................... 91

1379148 Ro Clamp, 1.5ID, 3”OD ............................................................................................................ 92

1379210 Fluted Roll Clamp, 2” core ........................................................................................................ 93

1379835 Stacker Rack .............................................................................................................................. 94

1379900 Vent Hood Assembly ................................................................................................................. 95

1379950 Infeed Assembly ........................................................................................................................ 96

1379871 Collimator Assembly, 55W ....................................................................................................... 97

1379872 Collimator Assembly, 100 & 150 Watt units ............................................................................. 98

1379130 Material Guide Roller Assembly ............................................................................................... 99

1379180 Accumulator Assembly ............................................................................................................ 101

1379918 Bag Closer Assembly ............................................................................................................... 102

1379190 Edge Guide Eye Assembly ...................................................................................................... 103

1379371 Safety Guard Kit ...................................................................................................................... 104

1379936 Bag Closing Assembly ............................................................................................................. 105

1379974 Bag Closing Clamp Assembly ................................................................................................. 106

1379990 Material Carriage Assembly .................................................................................................... 107

1379D-PD Pneumatic Diagram .............................................................................................................. 109

1379D-PD1 Pneumatic Diagram ............................................................................................................ 110

1379D-PD2 Chiller Plumbing Diagram, 150 Watt ................................................................................. 111

1379-WD1 Cabinet Wiring Diagram ...................................................................................................... 112

1379-WD2 Bus Coupler I/O Wiring Diagram ........................................................................................ 113

1379-WD3 Laser Interface Wiring Diagram .......................................................................................... 114

1379-WD4 Laser Interface Wiring Diagram .......................................................................................... 115

1379-WD5 Interlock Safety Circuit Wiring Diagram ............................................................................ 116

1379-WD6 Pendant Wiring Diagram ..................................................................................................... 117

1379-WD7 Wiring Diagram, Safety Circuit ........................................................................................... 118

1379-WD8 Laser Interface Wiring Diagram, 150 Watt ......................................................................... 119

Important Safety Instruction This part of the Instruction Material is provided for the safe use of your equipment. It contains important information to help work safely with the unit and describes the dangers inherent in machinery. Some of these dangers are obvious, while others are less evident.

Mandatory Information

All persons operating and/or working on the 1379D Laser Cutter should read and understand all parts of the Safety Instructions. This applies, in particular, for persons who only operate and/or work on the unit occasionally (e.g. for maintenance and repair). Persons who have difficulty reading must receive particularly thorough instruction.

Scope of the Instruction Material

The Instruction Material comprises: Safety information Operator Instructions Electrical and Pneumatic diagrams

And may also include; A list of recommended spare parts Instruction Manual(s) for components made by other manufacturers The layout and installation diagram containing information for installation

Intended Use

Our machines are designed and built in line with the state of the art and the accepted safety rules. However, all machines may endanger the life and limb of their users and/or third parties and be damaged or cause damage to other property, particularly if they are operated incorrectly or used for purposes other than those specified in the Instruction Manual.

Exclusion of Misuse

Non-conforming uses include, for example, using the equipment for something other than it was designed for, as well as operation without duly installed safety equipment. The risk rests exclusively with the end user. Conforming use of the machine includes compliance with the technical data, information and regulations in all parts of the complete Instruction Material, as well as compliance with the maintenance regulations. All local safety and accident prevention regulations must also be observed.


Liability

The machine should only be operated when in perfect working order, with due regard for safety and the potential dangers, as well as in accordance with the Instruction Material. Faults and malfunctions capable of impairing safety should be remedied immediately. We cannot accept any liability for personal injury or property damage due to operator errors or non-compliance with the safety instructions contained in this booklet. The risk rests exclusively with the end user. The Instruction Material should always be kept near the machine so that it is accessible to all concerned. The local, general, statutory and other binding regulations on accident prevention and environmental protection must also be observed in addition to the Instruction Material. The operating staff must be instructed accordingly. This obligation also includes the handling of dangerous substances and provision/use of personal protective equipment. The Instruction Material should be supplemented by instructions, including supervisory and notification duties with due regard for special operational features, such as the organization of work, work sequences, the personnel deployed, etc. The personnel's awareness of the dangers and compliance with the safety regulations should be checked at irregular intervals.

Choice and Qualification of Personnel

Ensure that work on the machine is only carried out by reliable persons who have been appropriately trained for such work - either within the company, by our field staff or at our office - and who have not only been duly appointed and authorized, but are also fully familiar with the local regulations. Work on the machine should only be carried out by skilled personnel, under the management and supervision of a duly qualified engineer. This not only applies when the machine is used for production, but also for special work associated with its operation (start-up and maintenance), especially when it concerns work on the hydraulic or electrical systems, as well as on the software/serial bus system.

Training

Everyone working on or with the machine should be duly trained and informed with regard to correct use of the safety equipment, the foreseeable dangers which may arise during operation of the machine and the safety precautions to be taken. In addition, the personnel should be instructed to check all safety mechanisms at regular intervals.

Responsibilities

Clearly define exactly who is responsible for operating, setting-up, servicing and repairing the machine. Define the responsibilities of the machine operator and authorize him to refuse any instructions by third parties if they run contrary to the machine's safety. This applies in particular for the operators of machines linked to other equipment. Persons receiving training of any kind may only work on or with the machine under the constant supervision of an experienced operator. Note the minimum age limits permitted by law.

A Word to the Operator

The greatest danger inherent in our machines: is that of fingers, hands or loose clothing being drawn into a machine by live, coasting or rotating tools or assemblies or of being cut by sharp tools or burned by hot elements. ALWAYS BE CONSCIOUS OF THESE DANGERS!

Safety Equipment on the Machines

All machines are delivered with safety equipment, which shall not be removed or bypassed during operation. The correct functioning of safety equipment on machines and systems should be checked every day and before every new shift starts, after maintenance and repair work, when starting up for the first time and when restarting (e.g. after prolonged shutdowns).

If safety equipment has to be dismantled for setting-up, maintenance or repair work, such safety equipment shall be replaced and checked immediately upon completing the maintenance or repair work. All protective mechanisms shall be fitted and fully operational whenever the machine is at a standstill or if it has been shut down for a longer period of time.

Damage

If any changes capable of impairing safety are observed in the machine or its mode of operation, such as malfunctions, faults or changes in the machine or tools, appropriate steps must be taken immediately, the machine switched off and a proper lockout tagout procedure followed. The machine should be examined for obvious damage and defects at least once per shift. Damage found shall be immediately remedied by a duly authorized person before resuming operation of machine. The machine should only be operated when in perfect working order and when all protective mechanisms and safety equipment, such as detachable protective mechanisms, emergency STOP systems, etc. are in place and operational.

Faults or Errors

The machine must be switched off and all moving or rotating parts allowed to come to a standstill and secured against accidental restart before starting to remedy any faults or errors.

Signs on the Machine

Safety and danger signs on the machine should be observed and checked at regular intervals to ensure that they are complete and undamaged. They should be clearly visible and legible at all times. Clothing, Jewelry, Protective Equipment Long loose hair, loose-fitting clothes, gloves and jewelry, including rings, should be avoided in order to avoid injuries due to being caught, drawn in and wound up inside the machine.


Protective Eyewear Protective eyewear that has been tested by the local authorities should be worn whenever there is a possibility of loose or flying objects or particles such as when cleaning the machine with compressed air.

Tools

Always count the number of tools in your possession before starting work on the machine. This will allow you to check that no tools have been left behind inside the machine. Never leave a tool in the machine while working.

Oils, Lubricants, Chemicals

Note the applicable safety regulations for the product used.

No Smoking, Fire, Explosion Hazard

Smoking and open flame (e.g. welding work) should be prohibited in the production area due to the risk of fire and explosions.

Workplace

A clear working area without any obstructions whatsoever is essential for safe operation of the machine. The floor should be level and clean, without any waste. The workplace should be well lit, either by the general lighting or by local lights.

Emergency STOP

The emergency STOP buttons bring all machine movements to a standstill. Make sure you know exactly where they are located and how they work. Try them out. Always ensure easy access to the nearest emergency STOP button while working on the machine.

First Aid

1. Keep calm even when injured. 2. Clear the operator from the danger zone. The decision of what to do and whether to seek

additional assistance rests entirely with you, particularly if someone has been trapped. 3. Give First Aid. Special courses are offered by such organizations as the employers' liability

insurance association. Your colleagues should be able to rely on you and vice versa. 4. Call an ambulance. Do you know the telephone numbers for the ambulance service, police and

fire service?

Important Notices

Reporting and Fighting Fires

Read the instructions posted in the factory with regard to reporting fires and the emergency exits. Make sure you know exactly where the fire extinguishers and sprinkler systems are located and how they are operated. Pass on the corresponding information to the firemen when they arrive. Ensure there are enough signs to avoid fire hazards. The following fire extinguishers may be used: - Dry powder extinguishers, ABC fire-extinguishing powder. - Carbon dioxide fire extinguishers to DIN 14461 for electronic components. Great care must be exercised when using carbon dioxide fire extinguishers in confined, badly ventilated rooms (see DIN 14406 and 14270). Isolate the machine from the power supply if a fire breaks out. Do not use water on burning electrical parts until it is absolutely certain that they have been completely disconnected from the power supply. Burning oils, lubricants, plastics and coatings on the machine can give off gases and vapors that may be harmful to your health. A qualified person should be consulted to repair the damage after a fire.

Electrical Power Supply

Before undertaking any maintenance or repair work on the machine, switch off the electrical power to the machine at the main source and secure it with a padlock so that it cannot be switched on again without authorization. In practice, this may mean that the technician, electrician and operator all attach their own padlock to the master switch simultaneously so that they can carry out their work safely. Locking extension plates should be available for multiple locks if required. The primary purpose for a lockout/tagout procedure is to protect workers

from injury caused by unexpected energizing or start-up of equipment. Energy sources (electrical/pneumatic/hydraulic, etc.) for the equipment shall be turned off or disconnected and the switches locked or labeled with a warning tag. It is the responsibility of the employer to establish control procedures. Follow lockout/tagout procedures before, setup and/or any service or maintenance work is performed, including lubrication, cleaning or clearance of jams. Caution: The machine is still not completely de-energized even when the master switch is off. - Electricity - The machine is always isolated from the electrical power supply whenever the master switch has been switched off. However, this does not apply for the power supply in the control cabinet, nor for equipment that does not draw its power via the master switch. - Pneumatic / hydraulic energy - Almost all our machines carry compressed air. In addition to switching off the master switch, the air supply must also be disconnected and the machine checked to ensure it is depressurized before starting any work on the machine; otherwise the machine may execute uncontrolled movements.


- Kinetic energy - Note that some motors or spindles, for example, may continue to run or coast run on after being switched off. - Potential energy - Individual assemblies may need to be secured if necessary for repair work.

Delivery of the Machine/Packaging

Note any markings on the packaging, such as weights, lifting points and special information. Avoid temperature fluctuations. Condensation may damage the machine.

Transport Damage

The packaging and machine must immediately be examined for signs of damage in transit. Such damage must be reported to the shipper/transporter within the applicable time limits. Contact Atlanta Attachment Company and/or your transport insurer immediately, if signs of damage are visible. Never operate a damaged machine.

Interim Storage

If the machine has to be stored temporarily, it must be oiled or greased and stored in a dry place where it is protected from the weather in order to avoid damage. A corrosion-inhibiting coating should be applied if the machine has to be stored for a longer period of time and additional precautions taken to avoid corrosion.

Transporting the Machine

Disconnect the machine from all external connections and secure any loose assemblies or parts. Never step under a suspended load. When transporting the machine or assemblies in a crate, ensure that the ropes or arms of a forklift truck are positioned as close to the edge of the crate as possible. The center of gravity is not necessarily in the middle of the crate. Note the accident prevention regulations, safety instructions and local regulations governing transport of the machine and its assemblies. Only use suitable transport vehicles, hoisting gear and load suspension devices that are in perfect working order and of adequate carrying capacity. Transport should only be entrusted to duly qualified personnel. Never allow the straps to rest against the machine enclosure and never push or pull sensitive parts of the machine. Ensure that the load is always properly secured. Before or immediately after loading the machine, secure it properly and affix corresponding warnings. All transport guards and lifting devices must be removed before the machine is started up again. Any parts that are to be removed for transport must be carefully refitted and secured before the machine is started up again.

Workplace Environment

Our machines are designed for use in enclosed rooms: Permissible ambient temperature approx. 5 - 40 °C (40 - 104 °F). Malfunctions of the control systems and uncontrolled machine movements may occur at temperatures outside this range. Protect against climatic influences, such as electrostatic charges, lightning strikes, hail, storm damage, high humidity, salinity of the air in coastal regions.

Protect against influences from the surroundings: no structure-borne vibrations, no grinding dust, or chemical vapors. Protect against unauthorized access. Ensure that the machine and accessories are set up in a stable position. Ensure easy access for operation and maintenance (Instruction Manual and layout diagram); also verify that the floor is strong enough to carry the weight of the machine.

Local Regulations

Particular attention must be paid to local and statutory regulations, etc. when installing machines and the plant (e.g. with regard to the specified escape routes). Note the safety zones in relation to adjacent machines.

Maintenance

General Safety Instructions

The machine shall be switched off, come to a standstill and be secured so that it cannot be switched on again inadvertently before starting any maintenance work whatsoever. Use proper lockout/tagout procedures to secure the machine against inadvertent startup. Remove any oil, grease, dirt and waste from the machine, particularly from the connections and screws, when starting the maintenance and/or repair work. Do not use any corrosive-cleaning agents. Use lint-free rags. Retighten all screw connections that have to be loosened for the maintenance and repair work. Any safety mechanisms that have to be dismantled for setting-up, maintenance or repair purposes must be refitted and checked immediately after completing the work.

Maintenance, Care, Adjustment

The activities and intervals specified in the Instruction Manual for carrying out adjustments, maintenance and inspections must be observed and parts replaced as specified. All hydraulic and pneumatic lines should be examined for leaks, loose connections, rubbing and damage whenever the machine is serviced. Any defects found must be remedied immediately.

Waste, Disassembly, Disposal

Waste products should be cleared from the machine as soon as possible as not to create a fire hazard. Ensure that fuels and operating lubricants, as well as replacement parts are disposed of in a safe and ecologically acceptable manner. Note the local regulations on pollution control. When scrapping (disassembling) the machine and its assemblies, ensure that these materials are disposed of safely. Either commission a specialist company familiar with the local regulations or note the local regulations when disposing of these materials yourself. Materials should be sorted properly.


Repair

Replacement Parts

We cannot accept any liability whatsoever for damage due to the use of parts made by other manufacturers or due to unqualified repair or modification of the machine.

Repair, Electrical

The power supply must be switched off (master switch off) and secured so that it cannot be switched on again inadvertently before starting any work on live parts. Those parts of the machine and plant on which inspection, maintenance or repair work is to be carried out must be isolated from the power supply, if specified. The isolated parts must first be checked to determine that they are truly de-energized before being grounded and short-circuited. Adjacent live parts must also be isolated. The protective measures implemented (e.g. grounding resistance) must be tested before restarting the machine after all assembly or repair work on electric parts. Signal generators (limit switches) and other electrical parts on the safety mechanisms must not be removed or bypassed. Only use original fuses or circuit overloads with the specified current rating. The machine must be switched off immediately if a fault develops in the electrical power supply. The electrical equipment of our machines must be checked at regular intervals and any defects found must be remedied immediately. If it is necessary to carry out work on live parts, a second person should be on hand to operate the emergency OFF switch or master switch with voltage release in the event of an emergency. The working area should be cordoned off and marked by a warning sign. Only use electrically insulated tools.

Ventilation/Hazardous Gases

It is the end users responsibility to ensure adequate ventilation is provided to exhaust any and all noxious or hazardous gases that may be present in the working environment.

Hydraulic and Pneumatic Systems

Work on hydraulic or pneumatic equipment shall only be carried out by persons with training, knowledge and experience of hydraulic systems. Pressure lines shall be depressurized before starting any repair work.

General Liability

Liability for machine damage and personal injury is extinguished completely if any unauthorized conversions or modifications are undertaken. The machine must not be modified, enlarged or converted in any way capable of affecting safety without the manufacturer's prior approval.

Starting Machine Movements

Read the Instruction Manual carefully to establish which keys and functions start machine movements.

A Word to the End User The end user has sole responsibility to enforce the use of safety procedures and guards on the machine. Any other safety devices or procedures due to local regulations should be should be retrofitted in accordance to these regulations and/or the EC Directive on the safety of machines. Operator’s position must always be readily accessible. Escape routes must always be kept clear and safety areas should be identified.

Safety Precautions Safety should be a constant concern for everyone. Always be careful when working with this equipment. While normal safety precautions were taken in the design and manufacture of this equipment, there are some potential safety hazards. Everyone involved with the operation and maintenance of this equipment should read and follow the instructions in this manual. Operate the equipment only as stated in this manual. Incorrect use could cause damage to the equipment or personal injury. It is the owner’s responsibility to make certain that the operator reads and understands this manual before operating this equipment. It is also the owner’s responsibility to make certain that the operator is a qualified and physically able individual, properly trained in the operation of this equipment. Specific safety warning decals are located on the equipment near the immediate areas of potential hazards. These decals should not be removed or obliterated. Replace them if they become non-readable.

• ALWAYS keep safety shields and covers in place, except for servicing. • ALWAYS operate equipment in daylight or with adequate working lights. • Follow daily and weekly checklists, making sure hoses are tightly secured and bolts are

tightened. • ALWAYS watch and avoid holes or deep depressions. • ALWAYS wear adequate eye protection when servicing the hydraulic system and battery. • NEVER operate a poorly maintained machine. • NEVER allow persons to operate this machine without proper instruction. • NEVER put hands or feet under any part of the machine while it is running. • NEVER attempt to make any adjustments or repairs to the machine while running. Repairs or

maintenance should be performed by trained personnel only. • NEVER work under the machine unless it is safely supported with stands, blocks or a hoist and

blocks. • NEVER touch hot parts of machine.


1.- MACHINE LAYOUT It is important that the service technician read the “1379D Laser Cutter Technical Manual & Parts List” FIRST to familiarize himself or herself with the operations and layout of the 1379D Series Laser Cutting Machine.

1.1.- Machine Components

1379DIAGRAMA DE ENHEBRSO 1.- Main Power Switch 5.- Infeed Closer Station 9.- Laser Cut Table & Heads 2.- Touch Screen 6.- Infeed Edge Guide 10.- Stacker Outfeed Folder 3.- Control Panel 7.- Infeed Pinch Roller 11.- Rewinder Drive 4.- Infeed Material Cart 8.- Left & Right Lasers 12.- Stacker & Rewind Station

(1)

(2) (3)

(X)

(Y)

(8)

(6)

(11)

(10)

(8)

(12)

(7)

(4)

(5)

(9)

1.2.- Machine Layout

EXHAUST DUCT LOCATION DIMENSIONS AAC EXHAUST KIT PART#: 1379-KIT1

(KIT INCLUDES 12” EXHAUST FAN, PLENUM, AND TWELVE FEET OF 6” DIAMETER FEXIBLE DUCT)

IF AAC EXHAUST KIT IS NOT USED, INSTALL A 12” OR LARGER EXHAUST FAN SIMILAR TO GRAINGER PART# 4YC69 WITH A FLOW OF 750 CFM OR GREATER. AN INLINE DUCT FAN SIMILAR TO GRAINGER PART# 4YM42 CAN ALSO BE USED WITH THIS SYSTEM.


1.3.- Machine Material Thread-Up Diagrams

1.4.- Lockout/Tagout Program

"Lockout/Tagout (LOTO)" refers to specific practices and procedures to safeguard employees from the unexpected energization or startup of machinery and equipment, or the release of hazardous energy during service or maintenance activities. This requires that a designated individual turns off and disconnects the machinery or equipment from its energy source(s) before performing service or maintenance and that the authorized employee(s) either lock or tag the energy-isolating device(s) to prevent the release of hazardous energy and take steps to verify that the energy has been isolated effectively. The following references provide information about the LOTO process.

Equipment Energy Control Procedure Lockout/Tagout Program

Description: Laser Cutter Workstation Model: 1379D Series Laser Cutter

Manufacturer: Atlanta Attachment Co. Location:

Energy Location Magnitude Control Method

Electrical: X Disconnect/Ctrl Box 220V Lockout & Tag

Pneumatic: X Main Regulator 95 PSI Lockout & Tag

Gravity: X Infeed Dancer Bar Lower Dancer to Lowest Position

Nonionizing Radiation

X Laser Heads & Optical Beam Paths 50 to 150 Watts Lockout & Tag or Laser Use Permit

(Needed for Alignment ONLY)

Remember to Release All Stored Energy! Shutdown Procedure:

1. Inform all affected personnel that the machine will be in Lockout status. 2. Follow proper shutdown procedure for Computer System & Windows OS 3. After Computer system is shutdown, turn the power and pneumatic disconnects

to the OFF position. (See Figures on next page for Disconnect Locations) 4. Fill out the tag with necessary information of the Lockout. 5. Install the Lockout device. 6. Disable Laser by turning the “Master Switch Control” key to the “Laser Disabled” position. 7. Remove “Master Switch Control” key 8. Verify all stored electrical energy has been released by pressing the power on button.

Use a meter to test circuits in the electrical panel to insure stored energy is released. 9. Perform necessary maintenance, services and/or repairs.

Startup Procedure: 1. Inform all affected personnel that the Lockout of this machine is being removed. 2. Replace any guards or safety devices which may have been removed during maintenance. 3. Remove the Lockout device and tag. 4. Turn the power and pneumatic disconnects to the ON position. 5. Insert “Laser Master Key” into “Master Switch Control” box and turn key to “Laser Enabled” 6. Push the green button below computer monitor screen to turn the machine on. 7. Inform all affected personnel that the Lockout has been removed and that the machine is ready for normal production

operation. Approved By: _______________________ Date: _________________________


1.5.- Laser Output Characteristics

The following information describes the output characteristics of the current 1379D Laser Cutter production model

configurations

LASER OUTPUT INFORMATION

Laser Type

Manufacturer/Model

Class

Wavelength

(nm)

Average Power (Watts)

Beam Diameter

(mm) 1 CO² Coherent, Inc.

Diamond C-55A IV 10550 ~ 10650 55 1.8

2 CO² Coherent, Inc. GEM-100A IV 10600 100 3.8

3 CO² Coherent, Inc. Diamond E-150 IV 10200~10800 150 2.2

4 5

6

1.6.- Laser Personal Protective Equipment

The following information describes the recommended eyewear for the 1379D Series Laser Cutter Family

LASER EYEWEAR INFORMATION

Laser Type

Wavelength (nm)

1379D Series Model

Optical Density (OD)

Remarks

1 CO² 10550 ~ 10650 1379D >5.0 Glendale/Sperian LOTG-CO2

2 CO² 10600 1379D100 >5.0 Glendale/Sperian LOTG-CO2

3 CO² 10200~10800 1379D150 >5.0 Glendale/Sperian LOTG-CO2

4


2.- MACHINE SETUP

2.1.- General Machine Data

Electrical / Pneumatic Requirements / Weight / Dimensions Electrical: 208~240 VAC (230VAC Recommend Voltage), Single Phase, 50/60 Hz, 30Amp PLEASE NOTE: If power falls below 208VAC a buck & boost transformer will have to be installed to boost the power to 230VAC (AAC Part# MM4161141 or Grainger Part# 1H279) Pneumatic: 85~110 PSI (95 PSI Recommended), 12 SCFM avg. Recommended Operating Temperatures: 50º F to 95º F Approx. Shipping Weight: 5,000 lbs. Machine Dimensions: (w/l/h, in) Infeed Material Cart: 121 x 35 x 40 Infeed Section: 143 x 94 x 96 Main Unit Section: 160 x 68 x 96 Stacker Cart: 104 x 25 x 46 Optional Rewinder Cart: 112 x 35 x 40 Motorized Infeed Carousel 120 x (length & height will vary by configuration)

2.2.- Optional Equipment & Accessories

The 1379D Laser Cutter is a very versatile machine. AAC has designed many options and accessories to complement this equipment as detailed below:

2.2.1.- Optional Equipment:

1367 - Motorized Infeed Carousel 1379-KIT1 - 12” Roof Mounted Exhaust System & Installation Kit 1379-KIT3 - Infeed Safety Guard Kit 1379-KIT4 - Laser Upgrade Kit to 150 Watt Liquid Cooled Laser 1379211 - 1.5” Diameter Roll Mandrel (Material Rod for Small rolls) 1379212 - 2.0” Diameter Roll Mandrel (Material Rod for Large rolls) 1379DW - Automatic Material Rewinder w/ Perforation Software Upgrade 1379835 - Stacker Cart (Spare Stacker Cart) 1379990 - Infeed Material Roll Cart (Spare Infeed Material Cart) 1379437 - Rewinder Cart Assembly (Spare Rewinder Cart)

2.2.2.- Optional Accessories:

1379-TECH - Technician Laser & Optics Alignment Kit 1379400 - Spare Plate Kit for Laser Cut Table & Channel 210CV28040095ZS - Spare Lens, 1.1" x 3.75" Focal Length, Plano-Convex 210CM28030X45FS- Spare Mirror, 1.1" x 3MM CO2 MM4161141 - Transformer, Buck & Boost, 0.75 kVA OCK-50 - Laser optics cleaning kit AC-100 - Laser thermal alignment cards (BOX of 100) MM2CVE1 - Laser Safety Glasses, CO2 Lasers (ONLY) LS1098297 - Laser Power Meter, Analog/Digital LS1098398 - Laser Thermopile Sensor for 150Watt CO2 (Max)


E-Z Laser

A few important things to keep in mind: The E-Z Laser software accesses the hard drive of the PC during operation. It is highly recommended to close the software before turning the Main power off to the machine which also turns off the power to the PC. Do this by clicking the red "X" at the extreme top right of the E-Z Laser software window. Clicking the Language on any screen will bring up the Language screen and will allow you to select any available language.

1

Definitions

Machine Axis - The machine has two Servo motors; One for each Axis of movement. X-Axis is the left and right movement of the carriage. Y-Axis is the Roller movement or front to back. Left and Right are defined by standing at the Infeed section of the machine and facing the Laser portion of the machine. Machine Homing - Homing (or Home-Out) is the process of moving the X and Y axis to a known physical location in order to establish a zero point for these axes. Machine Status Modes - Modes are used to control how the machine behaves under certain conditions. The modes are as follows: 1. Stopped - The machine is on but the servo motor controllers are off. No machine movement can occur in this mode. 2. Running - The machine is operating normally and is cutting. 3. Paused - The machine is operating normally and is NOT cutting. 4. Manual - The user has accessed the Manual Operations Screen and can move the machine manually. NOTE: When leaving the Manual Operations Screen the machine may automatically Home-Out if needed. Style - A Style is a collection of data necessary for the machine to produce panels, such as: Length, Width, Feedrate, etc... Pattern - A Pattern is the dimensional information contained in the style. Message Boxes -These boxes (shown below) are used any time the machine needs to convey information to the user.


For the purposes of this manual, the terms Click and Double-click using a mouse also refers to "Pressing" a button using the touch screen. At various time during operation of the machine, numeric data is required. When needed, a keypad screen is provided (see below). For the purposes of this manual, the term keypad will be referring to this screen.

Several screens have user-settable values, they are: Style Screen - See “Style Screen” on page 30. Edit Materials - See “Edit Materials” on page 31 Settings - See “Settings” on page 36. Technician - See “Technician Screen” on page 38 Clicking on the name of the setting displays a message box containing an explanation of that particular setting (as shown below).

Main Run Screen

The Main Run Screen is displayed the entire time the E-Z Laser software is active. It is divided into 5 areas - Graphics Area, Order Setup, Order Information, Machine Status, and a row of Command Buttons. Graphics Area - Displays the name and graphic of the currently selected style.

If a screen external to the E-Z Laser software comes up in front of the graphics window it erases the graphic. Clicking anywhere inside the graphics window will restore it.


Order Setup

Select Style - The drop-down box labeled Select Style allows the user to change styles. Material Type - Displays the material used for the current Style. Order Quantity - Allows the user to enter in how many panels of the selected style as needed via a keypad. Current Count - Allows the user to modify the current count via a keypad. Left to Cut - Displays the remaining panels for the current order. New Order - Resets the Current Count to zero, changes the Left to cut display to the correct number, and clears the data in the Order Information window. Edit Styles - Brings up the Styles screen. Order Information

Seconds to Cut Current Panel - Displays how many seconds it takes to run the current style. Total Minutes for Current Order - Displays how many run minutes the machine will take to complete the order. Run Minutes to Complete Order - Displays how many run minutes required to complete the current order. Yards Needed for Current Order - Displays how many yards of material will be needed to complete the order. NOTE: All time information shown above is reset by pressing the New Order button in the Order Setup area of the Main Run Screen. Machine Status - displays the User Piece Count and the current operational status of the machine.

Reset Piece Count - Resets the User Piece Count to zero.

Command Buttons

provide user control of the machine and are as follows: Start/Pause - The Start button is a multi-functional button that provides machine control and displays the current Mode status. When the button's caption displays "Start" the machine is currently Paused and ready to start cutting.

When the button's caption displays "Pause" the machine is currently running; by clicking the button it will pause the machine.

When the button's caption displays "Stopped" the machine is currently stopped and the Servos are off. Clicking the button will do nothing.

When the button's caption displays "Manual" the machine is currently in Manual mode. Clicking the button will do nothing.


When the button's caption displays "Homing" the machine is currently in Homing mode. Clicking the button will do nothing.

Finish Pattern - The Finish Pattern Button will pause the machine at the end of a pattern. The button color turns yellow when clicked and will stay yellow after the pattern is finished until the Start button is clicked. This allows the user to see that the machine was paused because of a Finish Pattern button click. Load Material - See “Load Material” on page 25. Manual - “See “Manual Operations” on page 26. Add Splice - The Add Splice Button is used when splicing a new roll to the existing roll. The splice will be automatically removed at the appropriate time. Utilities - See “Utilities” on page 33. Help - Displays this Help file Language - See Page 18. Reset/Servos On When the button's caption displays Reset the servos are OFF and the machine is inoperable. Clicking the button turns power on to the Servos and homes-out the machine. CAUTION: the machine will move during the homing function.

When the button's caption displays Turn Servos Off the servos are ON and the machine is ready to run. Clicking the button turns off power to the Servos. NOTE: When the Servos are off none of the Machine Axes will move.

Load Material

2

This screen provides functions needed when loading a new roll of material. Y Axis Jog - Allows the user to move the roller forward or in reverse as indicated by the direction of the arrows shown on the buttons. Infeed Jog - Allows the user to move the needed direction at a selected Fast or Slow speed as indicated by the direction of the arrows shown on the buttons. Rear Pinch Roller Up - Allows the user to raise the Rear Pinch roller to its up position. Rear Pinch Roller Down - Allows the user to raise the Rear Pinch roller to its down position. NOTE: One of the Pinch Roller buttons will have a green background denoting its current position. Trim Material - Starts the Trim Material cycle which makes a crosscut to the material with no roller feeding, then lifts the Rear Pinch Roller to allow the trimmed material to be removed.


Manual Operations

3

This screen allows the user to move the machine manually. NOTE: When leaving the Manual Operations Screen the machine may automatically Home-Out if needed. X - Y Axis Jog - Allows the user to move the Feed Rollers or the Laser Heads in the direction indicated by the arrows. X-Axis Position - Displays a graphic representation of the current position of the X axis (Laser Heads). X-Axis Location - Displays the current X location. Y-Axis Location - Displays the current Y location. Advanced Manual I/O - Advanced Manual I/O allows the user to access all of the input and output devices manually. Used only for testing. Stacker Cycle - Allows the user to start the Stacker Cycle. This will make the Stacker execute its entire cycle. Used only for testing.

Input/Output

The following Input/Output Screens allow you to see the current state of the Inputs and Outputs. It also allows you to activate/deactivate the Outputs. They are divided up into the areas listed below. 1. Infeed

Input Status - Displays the current state of the input device. Output Status - Displays the current state of the output device. These are also buttons. If clicked, it will reverse its state (if it is on it will turn off or if it is off it will turn on). Previous - Closes this screen and opens the General I/O screen Next - Closes this screen and opens the Laser I/O screen


2. Laser

Input Status - Displays the current state of the input device. Output Status - Displays the current state of the output device. These are also buttons. If clicked, it will reverse its state (if it is on it will turn off or if it is off it will turn on). Previous - Closes this screen and opens the Infeed I/O screen Next - Closes this screen and opens the Stacker I/O screen 3. Stacker

Input Status - Displays the current state of the input device. Output Status - Displays the current state of the output device. These are also buttons. If clicked, it will reverse its state (if it is on it will turn off or if it is off it will turn on). Previous - Closes this screen and opens the Laser I/O screen Next - Closes this screen and opens the General I/O screen 4. General

Input Status - Displays the current state of the input device. Output Status - Displays the current state of the output device. These are also buttons. If clicked, it will reverse its state (if it is on it will turn off or if it is off it will turn on). Previous - Closes this screen and opens the Stacker I/O screen Next - Closes this screen and opens the Infeed I/O screen NOTE: This I/O screens are primarily used to test the Inputs and Outputs. If you manually change the state of an Input it will not have an effect on the machine. However, if you click on one of the Output buttons it will reverse its state (if it is on it will turn off or if it is off it will turn on).


Style Screen

4

Style Name - This drop down box allows you to select an existing style and enter a name for a new style. Material Type - This drop down box allows you to select an existing Material Type for the currently selected Style. Edit Materials - See “Edit Materials” on page 31. Panel Type and Size - See “Panel Type & Size” on page 32. Notch Type - See “Notch Type” on page 32. Load Style - Loads the current style shown on the screen to the machine Save Style - Saves any modification or new pattern. Delete Style - Permanently deletes a pattern from the machine.

Edit Materials 1

5

This screen allows the user to define and name a new material which can then be associated to a style. Minimum Power - Minimum power setting for the laser for optimal cutting of the material. Minimum Power cannot be above Maximum Power. Maximum Power - Maximum power setting for the laser for optimal cutting of the material. Maximum Power cannot be below Minimum Power. Skip Power - Power setting for the laser when cutting Skips to hold the waste in place. When set to 100 no skips will be cut. Acceleration Time - The amount of time allowed for the machine to accelerate to set speed. Deceleration Time - The amount of time allowed for the machine to decelerate to set speed. Maximum Feedrate - Maximum speed that the machine can move and still cut the material properly. Adjustment Offset - Offsets the laser beam to the outside of the panel to allow for the width of the beam or to offset for any material melt. Slow Speed Percentage - The percentage of full speed the machines runs a various points in the pattern.


Panel Type & Size 2

Corner Type - This drop-down box allows the user to select Mitered, Round, or Square. Length - Length of the panel in inches. Width - Width of the panel in inches. Radius/Miter - Size of the Radius or Miter. Initiate Stack - The distance in inches that the panel needs to feed in order for the stacker to clamp the panel in the correct location. This ensures the panel is stacked evenly on both sides. Notch Type

6

Whichever combination of boxes are checked determine where notches will appear on the panel. Notch Size - This drop-down box allows the user to a small or large notch.

Utilities

7

As its name implies the Utilities Screen have several functions. Log Files - See “Log Files” on page 34. Communication Status - Monitors communication between the PC and the Servo Controller. Run Times - Total Runtime is only accumulated when the machine is actually running in Automatic mode. Total Laser Head n Time is only accumulated when the Lasers Heads are actually On. Efficiency Data - See “Efficiency” on page 34. System Information - See “System Information” on page 35. Security - See “Security” on page 35. Settings - See “Settings” on page 36. Shift Data - See “Shift Data”37


Log Files By default the Log File displayed is the file for the current day. Note the filename of the Log File is 060218.txt; this represents 02/18/06 or February 18th, 2006. 06 is the year, 02 is the month, and 18 is the day.

All Log Files are stored in a directory called C:\EZLaser\Logs\. NOTE: Log Files are automatically deleted after a number of days defined by the Keep Log Files for" Setting. Browse Button - Allows you to navigate to a different Log file. Excel Button - Allows you to open the current Log file in a Microsoft Excel spreadsheet. NOTE: For the Excel function to work Microsoft Excel has to be installed on this computer. Efficiency

Efficiency Statistics are calculated based on the amount of time the machine is in Run Mode (cutting panels) divided by the amount of time the machine is turned on.

Time Display changes the format the on and run times are displayed in. The Last Reset box displays the last time the Reset button was pressed resetting the On and Run Times to 0 (zero).

8

Reset Button - Resets all efficiency data. System Information

9

System Info. - Displays configuration and hardware settings for the PC. View History - Displays the Revision History in Notepad as a text file. Security

Security levels from lowest to highest are as follows: 1. Operator 2. Supervisor 3. Mechanic 4. Head Mechanic

Operator is the default level. There is no code for this level. When the machine is turned on it is always at this level. The codes can be changed for each level by following the instructions on the screen (see above). NOTE: Once someone has raised the current security level to something other than Operator (for example to Mechanic) the machine will stay at this level until the machine is turned off or the Reset to Operator button is clicked.


Settings

10

User settable conditions are as follows: Keep Log Files for XX Days - Log Files are automatically deleted after the number of days defined by this setting. Servo Errors Enabled - If set to No any servo generated errors are ignored. Accumulator Full Move Time - The amount of time allowed for the Accumulator Full sensor to be made. Range = 1.00 to 15.00 seconds, Default = 5.00 Accumulator Off Sensor Time - The amount of time allowed for the Accumulator to move off of the Accumulator Full sensor. Range = 1.00 to 4.00 seconds, Default = 3.00 Infeed at Speed Time - The amount of time allowed for the Infeed Roll to reach its preset speed. Range = 1.00 to 10.00 seconds, Default = 3.00 Laser Home Time - The amount of time allowed for the Laser Heads to complete their Homing cycle. Range = 5.00 to 15.00 seconds, Default = 10.00 Laser Ok Time - The amount of time allowed for the Laser Heads to return an OK signal once they have been commanded to turn on. Range = 1.00 to 10.00 seconds, Default = 5.00 Laser Power Ok Time - The amount of time allowed for the Laser Heads to return an OK signal for the Power Supply once they have been commanded to turn on. Range = 0.00 to 1.00 seconds, Default = .50 Outfeed Jam Detect Delay - The amount of time allowed for the completed panel to be pulled away from the Outfeed Jam Detect sensors by the Stacker. Range = 1.00 to 5.00 seconds, Default = 3.00 Laser Home Shift - The distance the Laser Head moves to Home position after the Laser Reference sensor is made. Range = 0 (zero) to 6.000 inches, Default = 1.600 Stacker Move Time - The amount of time allowed for the Stacker funnel to move to either it’s in or out position. Range = 1.00 to 5.00 seconds, Default = 3.00 Stack Hold Delay - The amount of delay time after the Stack Shift is fired until the Stack Hold is fired. Range = 0.00 to 5.00 seconds, Default = 2.00 Stack Hold Retract Delay - The amount of time used to delay the retraction of the Stack Hold air cylinders after the Stack Shift is told to move to the in position. X Axis Scale Adjustment - The X Axis Scale Adjustment is a percentage number used to slightly modify the amount of feed per increment. In other words, a 10 inch feed at 100% would be 10 inches. A 10 inch feed at 110% would be 11 inches.

Range = 50.0% to 150.0%, Default = 100.0% Y Axis Scale Adjustment - The Y Axis Scale Adjustment is a percentage number used to slightly modify the amount of feed per increment. In other words, a 10 inch feed at 100% would be 10 inches. A 10 inch feed at 110% would be 11 inches Range = 50.0% to 150.0%, Default = 100.0% Panel Separator Move Time - The amount of time allowed for the Panel Separator to move to either the On or Off position. Range = 0 to 3.00 seconds, Default = 2.00 The numeric settings have upper and lower limits. If you type in a number higher than the limit the entry will automatically change to the upper limit. The same happens with the lower limit, it will automatically change to the lower limit. Shift Data

The E-Z Laser is continually collecting Shift Data and storing it in a file. When the Shift Data Button is clicked on the Utility page the user is asked to select a Shift Data file. The files are named YYMMDDS.txt which means YY = Year, MM = Month, DD = Day, and S = Shift. An example would be 0909251.txt which means 09/25/2009 Shift 1. The Shift Data files are stored in C:\EZLaser\ShiftData. The graphic above illustrates how the data is is collected continually during any given defined shift.

Export Button - Exports the Shift Data to a comma-delimited text file stored in C:\EZLaser\ShiftData. Shift Setup Button - Allows the user to define 3 different shifts to be used for collecting Shift Data (see below).

11


Technician Screen

12

The Technician screen contains settings and functions used to setup and test the machine. The Laser Test and Commands sections are examples of these. Rapid Feedrate - The feedrate used by the machine when it is not cutting and can move as fast as possible. Material Roll Width - This is the distance the machine uses in order to know how far out to move when trimming and/or cutting apart panels. Splice Distance - This is the distance from the Laser heads to where a splice is sewn.

EPM Module

2.3.- Inverter Programming and Parameter Data

2.3.1. - Programming ACTech SCL/SCM Drive

The drive is already pre-programmed** with settings specifically for the 1379 Unit by Atlanta

Attachment Co. These settings are listed in the chart on the following page. Password protection is

currently disabled so that control of the parameters is immediately available to the user. After the

controller settings have been "fine-tuned", you can use parameter 44 to set a password value

between 1-999 to "lock" the control setting for the motors.

The buttons and display on the front of the motor controller can be used to change any specific

parameter. Pressing the mode button will take you to the last parameter viewed. Parameters are

designated with a "P" as the first character on the display. The arrow up and arrow down buttons

will scroll through to the desired parameter. Pressing "Mode" displays the current parameter

setting (point "above" decimal point blinks). This setting can be changed by using the arrow up and

arrow down buttons. When the desired setting is found press the mode button to store the new

value. This will store the new value and exit the program mode. To change another parameter

value, press the mode key again and repeat the procedure.

**In the event the controller has not been pre-programmed by AAC, the default password from the

factory is 225.

Every SCL/SCM Series drive has an Electronic Programming Module (EPM) installed on the main

control board. The EPM stores the user’s parameter settings and special OEM default settings (if

programmed). The EPM is removable, allowing it to be installed in another drive for quick set-up.

For example, if a drive is being replaced with a new one, the EPM can be taken out of the first drive

and installed in the new drive. Downtime is minimized because

the new drive does not require programming - it is ready to run

when the EPM is installed.

NOTE: The drive will not operate without the EPM installed. The drive will display “F1” if the EPM is missing

or damaged.

WARNING! Do not remove the EPM while power is applied to the drive. Damage to the EPM and/or drive may

result.

See tables on following pages...


2.3.2. - Infeed Pinch Roll Drive Motor Parameter Menu

AAC custom setting shown in last column. NO. PARAMETER NAME RANGE OF ADJUSTMENT FACTORY DEFAULT AAC

SETTING

01 LINE VOLTAGE High (01), LOW (02) HIGH (01) (02)

02 CARRIER FREQUENCY 4kHz (01), 6kHz (02), 8 kHz (03), 10 kHZ (04) 6 kHZ (02) (04)

03

START METHOD

NORMAL (01), START ON POWER UP (02), START WITH DC BRAKE (03), AUTO RESTART WITH DC BRAKE (04), FLYING RESTART 1 (05), FLYING RESTART 2 (06), FLYING RESTART 3 (07)

NORMAL (01)

---

04 STOP METHOD COAST (01), COAST W/ DC BRAKE (02), RAMP (03), RAMP W/ DC BRAKE (04)

COAST (01) (04)

05 STANDARD SPEED SOURCE

KEYPAD (01), PRESET #1 (02), 0-10VDC (03), 4-20mA (04)

KEYPAD (01) (02)

06

RELAY OUTPUT

NONE (01), RUN (02), FAULT (03), INVERSE FAULT (04), FAULT LOCKOUT (05), AT SET SPEED (06), ABOVE PRESET #3 (07), CURRENT LIMIT (08), AUTO SPEED (09), REVERSE (10)

NONE (01)

(06)

10

TB-13A FUNCTION SELECT

NONE (01), 0-10 VDC (02), 4-20 mA (03), PRESET SPEED #1 (04), START FORWARD (05), RUN REVERSE (06), START REVERSE (07), EXTERNAL FAULT (08), INVERSE EXT FAULT (09), AUXILARY STOP (10), ACCEL/DECEL #2 (11)

NONE (01)

(06)

11

TB-13B FUNCTION SELECT

NONE (01), 0-10 VDC (02), 4-20 mA (03), PRESET SPEED #2 (04), DECREASE FREQ (05), START FORWARD (06), JOG FORWARD (07), JOG REVERSE (08), EXTERNAL FAULT (09), INVERSE EXT FAULT (10), AUXILARY STOP (11), ACCEL/DECEL #2 (12), REMOTE KEYPAD (13)

NONE (01)

(04)

12

TB-13E INPUT FUNCTIONS TB-13 OUTPUT FUNCTIONS OTHER FUNCTIONS

NONE (01), 0-10 VDC (02), 4-20 mA (03), PRESET SPEED #3 (04), INCREASE FREQ (05), START FORWARD (06), EXTERNAL FAULT (07), INVERSE EXT FAULT (08), AUX STOP (09), ACCEL/DECEL #2 (10), RUN (11), FAULT (12), INVERSE FAULT (13), FAULT LOCKOUT (14), AT SET SPEED (15), ABOVE PRESET #3 (16), CURRENT LIMIT (17), AUTO SPEED (18), REVERSE (19), DYNAMIC BRAKING (20), REMOTE KEYPAD (21)

NONE (01)

---

14

CONTROL TERMINAL STRIP ONLY (01) REMOTE KEYPAD ONLY (02)

TERMINAL STRIP ONLY (01)

---

16 UNITS EDITING TENTHS OF UNITS (01), WHOLE UNITS (02) WHOLE UNITS (02) ---

17 ROTATION FORWARD ONLY (01), FORWARD AND REVERSE (02)

FORWARD ONLY (01)

(02)

19 ACCELERATION TIME 0.1 - 3600.0 SEC 20.0 SEC 1.0

20 DECELERATION TIME 0.1 - 3600.0 SEC 20.0 SEC 0.1

21 DC BRAKE TIME 0.0 - 3600.0 SEC 0.0 SEC ---

22 DC BRAKE VOLTAGE 0.0 - 30.0% 0.0 % ---

23 MINIMUM FREQUENCY 0.0 - MAXIMUM FREQUENCY 0.0 Hz ---

24

MAXIMUM FREQUENCY MINIMUM FREQUENCY - 240 Hz SCL = 50.0 Hz SCM = 60.0 Hz

60

25 CURRENT LIMIT 30 - 180 % 180 % 150

26 MOTOR OVERLOAD 30 - 100 % 100 % ---

27

BASE FREQUENCY 25.0 - 500 Hz SCL = 50.0 Hz SCM = 60.0 Hz

60

28 FIXED BOOST 0.0 - 30.0 % 1.0 % 20

29 ACCEL BOOST 0.0 - 20.0 % 0.0 % ---

30 SLIP COMPENSATION 0.0 - 5.0 % 0.00% ---

31 PRESET SPEED 0.0 - MAXIMUM FREQUENCY 0.0 Hz 30


33-37 0.0 0.0

38 SKIP BANDWIDTH 0.0 - 10 Hz 0.0 Hz ---

39 SPEED SCALING 0.0 - 6500.0 0.0 ---

42 ACCEL/DECEL #2 0.1 - 3600.0 SEC 20.0 SEC ---

44 PASSWORD 000 - 999 225 *000

45 SPD AT MIN SIGNAL MINIMUM FREQUENCY - 999 Hz 0.0 Hz ---

46 SPD AT MAX SIGNAL MINIMUM FREQUENCY - 999 Hz SCL = 50.0Hz SCM = 60.0Hz

---

47 CLEAR HISTORY MAINTAIN (01), CLEAR (02) MAINTAIN (01) ---

48

PROGRAM SELECTION

USER SETTINGS (01), OEM SETTINGS (02), RESET OEM (03), RESET 60 (04), RESET 50 (05), TRANSLATE (06)

SCL = RESET 50 (05) SCM = RESET 60 (04)

---

50 FAULT HISTORY (VIEW ONLY) (N/A) ---

51 SOFTWARE CODE (VIEW ONLY) (N/A) ---

52 DC BUS VOLTAGE (VIEW ONLY) (N/A) ---

53 MOTOR VOLTAGE (VIEW ONLY) (N/A) ---

54 LOAD VOLTAGE (VIEW ONLY) (N/A) ---

55 0-10 VDC INPUT (VIEW ONLY) (N/A) ---

56 4-20mA INPUT (VIEW ONLY) (N/A) ---

57 TB STRIP STATUS (VIEW ONLY) (N/A) ---

58 KEYPAD STATUS (VIEW ONLY) (N/A) ---

* PASSWORD IS SET TO “000” WHICH DISABLES THE PASSWORD FUNCTION


2.3.3. – (OPTIONAL) Rewinder Drive Motor Parameter Menu

AAC custom setting shown in last column.

NO. PARAMETER NAME RANGE OF ADJUSTMENT FACTORY DEFAULT AAC SETTING

01 LINE VOLTAGE High (01), LOW (02) HIGH (01) (02)

02 CARRIER FREQUENCY 4kHz (01), 6kHz (02), 8 kHz (03), 10 kHZ (04) 6 kHZ (02) (04)

03

START METHOD

NORMAL (01), START ON POWER UP (02), START WITH DC BRAKE (03), AUTO RESTART WITH DC BRAKE (04), FLYING RESTART 1 (05), FLYING RESTART 2 (06), FLYING RESTART 3 (07)

NORMAL (01)

---

04 STOP METHOD COAST (01), COAST W/ DC BRAKE (02), RAMP (03), RAMP W/ DC BRAKE (04)

COAST (01) (04)

05 STANDARD SPEED SOURCE

KEYPAD (01), PRESET #1 (02), 0-10VDC (03), 4-20mA (04)

KEYPAD (01) (03)

06

RELAY OUTPUT

NONE (01), RUN (02), FAULT (03), INVERSE FAULT (04), FAULT LOCKOUT (05), AT SET SPEED (06), ABOVE PRESET #3 (07), CURRENT LIMIT (08), AUTO SPEED (09), REVERSE (10)

NONE (01)

(01)

10

TB-13A FUNCTION SELECT

NONE (01), 0-10 VDC (02), 4-20 mA (03), PRESET SPEED #1 (04), START FORWARD (05), RUN REVERSE (06), START REVERSE (07), EXTERNAL FAULT (08), INVERSE EXT FAULT (09), AUXILARY STOP (10), ACCEL/DECEL #2 (11)

NONE (01)

(06)

11

TB-13B FUNCTION SELECT

NONE (01), 0-10 VDC (02), 4-20 mA (03), PRESET SPEED #2 (04), DECREASE FREQ (05), START FORWARD (06), JOG FORWARD (07), JOG REVERSE (08), EXTERNAL FAULT (09), INVERSE EXT FAULT (10), AUXILARY STOP (11), ACCEL/DECEL #2 (12), REMOTE KEYPAD (13)

NONE (01)

---

12

TB-13E INPUT FUNCTIONS TB-13 OUTPUT FUNCTIONS OTHER FUNCTIONS

NONE (01), 0-10 VDC (02), 4-20 mA (03), PRESET SPEED #3 (04), INCREASE FREQ (05), START FORWARD (06), EXTERNAL FAULT (07), INVERSE EXT FAULT (08), AUX STOP (09), ACCEL/DECEL #2 (10), RUN (11), FAULT (12), INVERSE FAULT (13), FAULT LOCKOUT (14), AT SET SPEED (15), ABOVE PRESET #3 (16), CURRENT LIMIT (17), AUTO SPEED (18), REVERSE (19), DYNAMIC BRAKING (20), REMOTE KEYPAD (21)

NONE (01)

(09)

14

CONTROL TERMINAL STRIP ONLY (01) REMOTE KEYPAD ONLY (02)

TERMINAL STRIP ONLY (01)

---

16 UNITS EDITING TENTHS OF UNITS (01), WHOLE UNITS (02) WHOLE UNITS (02) ---

17 ROTATION FORWARD ONLY (01), FORWARD AND REVERSE (02)

FORWARD ONLY (01)

(02)

19 ACCELERATION TIME 0.1 - 3600.0 SEC 20.0 SEC 0.5

20 DECELERATION TIME 0.1 - 3600.0 SEC 20.0 SEC 0.1

21 DC BRAKE TIME 0.0 - 3600.0 SEC 0.0 SEC 1.0

22 DC BRAKE VOLTAGE 0.0 - 30.0% 0.0 % 8.0

23 MINIMUM FREQUENCY 0.0 - MAXIMUM FREQUENCY 0.0 Hz ---

24

MAXIMUM FREQUENCY MINIMUM FREQUENCY - 240 Hz SCL = 50.0 Hz SCM = 60.0 Hz

60

25 CURRENT LIMIT 30 - 180 % 180 % 150

26 MOTOR OVERLOAD 30 - 100 % 100 % ---

27

BASE FREQUENCY 25.0 - 500 Hz SCL = 50.0 Hz SCM = 60.0 Hz

60

28 FIXED BOOST 0.0 - 30.0 % 1.0 % 20

29 ACCEL BOOST 0.0 - 20.0 % 0.0 % ---

30 SLIP COMPENSATION 0.0 - 5.0 % 0.00% ---



33-37 0.0 0.0

38 SKIP BANDWIDTH 0.0 - 10 Hz 0.0 Hz ---

39 SPEED SCALING 0.0 - 6500.0 0.0 ---

42 ACCEL/DECEL #2 0.1 - 3600.0 SEC 20.0 SEC 0.1

44 PASSWORD 000 - 999 225 *000

45 SPD AT MIN SIGNAL MINIMUM FREQUENCY - 999 Hz 0.0 Hz 0.0

46 SPD AT MAX SIGNAL MINIMUM FREQUENCY - 999 Hz SCL = 50.0Hz SCM = 60.0Hz

60

47 CLEAR HISTORY MAINTAIN (01), CLEAR (02) MAINTAIN (01) ---

48

PROGRAM SELECTION

USER SETTINGS (01), OEM SETTINGS (02), RESET OEM (03), RESET 60 (04), RESET 50 (05), TRANSLATE (06)

SCL = RESET 50 (05) SCM = RESET 60 (04)

---

50 FAULT HISTORY (VIEW ONLY) (N/A) ---

51 SOFTWARE CODE (VIEW ONLY) (N/A) ---

52 DC BUS VOLTAGE (VIEW ONLY) (N/A) ---

53 MOTOR VOLTAGE (VIEW ONLY) (N/A) ---

54 LOAD VOLTAGE (VIEW ONLY) (N/A) ---

55 0-10 VDC INPUT (VIEW ONLY) (N/A) ---

56 4-20mA INPUT (VIEW ONLY) (N/A) ---

57 TB STRIP STATUS (VIEW ONLY) (N/A) ---

58 KEYPAD STATUS (VIEW ONLY) (N/A) ---

* PASSWORD IS SET TO “000” WHICH DISABLES THE PASSWORD FUNCTION

Assembly Drawings & Parts Lists The materials contained herein are confidential and proprietary information of Atlanta Attachment Company. In addition to any confidentiality and non-disclosure obligations that currently exist between you and Atlanta Attachment Company, your use of these materials serves as an acknowledgment of the confidential and proprietary nature of these materials and your duty not to make any unauthorized use or disclosure of these materials.


11379D Dual Head Laser Cutter, 55Watt AAC Drawing Number 9002177 Rev 2

NO. QTY PART # DESCRIPTION NO. QTY PART # DESCRIPTION

1 2 1379013 GUARD, LASER, ASSEMBLY 11 AR 1379-LAB9 LABEL, AVOID EXPOSURE

2 1 1379153 VENT HOOD ASM, RIGHT SIDE 12 AR 1379-PD DIAGRAM, PNEUMATIC

3 1 1379200 LASER WORKSTATION,GENERIC 13 AR 1379-PD1 DIAGRAM, PNEUMATIC

4 1 1379211 ROLL MANDREL ASY,1.5 CORE 14 AR 1379-WD7 DIA.,WIRING, SAFETY

5 1 1379212 ROLL MANDREL ASSY,3" CORE 15 1 MM4161141 TRANSFORMER,BUCK BOOST

6 2 1379234 LASER SUB ASSY, 55W 16 5 MM5415K39 CLAMP,HOSE,WORM TYPE

7 1 1379835 RACK, STACKER 17 * 75FT MM5501K35 FLEX AIR DUCT,6" ID

8 1 1379900 VENT HOOD ASSEMBLY 18 2 MM693687 DOORSTOP,MAGNETIC W/CATCH

9 1 1379950 INFEED ASSEMBLY 19 2 MM98412A215 HITCH PIN 4.0UL, .5 OD

10 1 1379990 MATERIAL CARRIAGE ASM 20 1 AAAD000840 DRYER, PNEUMATIC AIR

Page 52 Page

Page 49 Page

Page 53

Page

Page 84

Page Page 85

Page

Page 83

Page

Page 95

Page

Page 94 Page

Page 96

Page

Page 110

Page

Page 109 Page

Page 107 Page

Page 118

Page

11379D100 Dual Head Laser Cutter, 100Watt AAC Drawing Number 9002186 Rev 4


1 AR 1379-LAB9 LABEL, AVOID EXPOSURE 12 1 1379900 VENT HOOD ASSEMBLY

2 AR 1379-PD DIAGRAM, PNEUMATIC 13 1 1379950 INFEED ASSEMBLY

3 AR 1379-PD1 DIAGRAM, PNEUMATIC 14 1 1379990 MATERIAL CARRIAGE ASM

4 AR 1379-WD7 DIA.,WIRING, SAFETY 15 1 AAAD000840 DRYER, PNEUMATIC AIR

5 2 1379006 GUARD, LASER, ASSEMBLY 16 1 MM4161141 TRANSFORMER,BUCK BOOST

6 1 1379153 VENT HOOD ASM, RIGHT SIDE 17 5 MM5415K39 CLAMP,HOSE,WORM TYPE

7 1 1379200 LASER WORKSTATION,GENERIC 18 * 75FT MM5501K35 FLEX AIR DUCT,6" ID

8 1 1379211 ROLL MANDREL ASY,1.5 CORE 19 1 MM5501K35 FLEX AIR DUCT,6" ID

9 1 1379212 ROLL MANDREL ASSY,3" CORE 20 2 MM693687 DOORSTOP,MAGNETIC W/CATCH

10 1 1379835 RACK, STACKER 21 2 MM98412A215 HITCH PIN 4.0UL, .5 OD

11 2 1379878 LASER SUB ASSY, 100W 22 1 MMT9945 TAPE,REFLECTIVE,2" WIDE

Page 118

Page Page 50

Page

Page 109

Page

Page 52

Page Page 53

Page

Page 110 Page

Page 94

Page

Page 83

Page Page 84 Page

Page 95

Page Page 96

Page

Page 87

Page

Page 107 Page


11379D150 Dual Head Laser Cutter, 150Watt AAC Drawing Number 9002870 Rev 0


1 1 1379-LAB9 LABEL, AVOID EXPOSURE 13 1 1379990 MATERIAL CARRIAGE ASM

2 1 1379-WD7 DIA.,WIRING, SAFETY 14 1 1379D-PD DIAGRAM, PNEUMATIC

3 1 1379153 VENT HOOD ASM, RIGHT SIDE 15 1 1379D-PD1 DIAGRAM, PNEUMATIC

4 1 1379200 LASER WORKSTATION,GENERIC 16 1 1379D-PD2 DIAGRAM, CHILLER PLUMBING

5 1 1379211 ROLL MANDREL ASY,1.5 CORE 17 1 AAAD000840 DRYER, PNEUMATIC AIR

6 1 1379212 ROLL MANDREL ASSY,3" CORE 18 1 MM4161141 TRANSFORMER,BUCK BOOST

7 2 1379461 GUARD, LASER, ASSEMBLY 19 5 MM5415K39 CLAMP,HOSE,WORM TYPE

8 2 1379492 LASER SUB ASSY, 150W 20 * 75FT MM5501K35 FLEX AIR DUCT,6" ID

9 1 1379498 COOLING SYSTEM ASM, LASER 21 2 MM693687 DOORSTOP,MAGNETIC W/CATCH

10 1 1379835 RACK, STACKER 22 2 MM98412A215 HITCH PIN 4.0UL, .5 OD

11 1 1379900 VENT HOOD ASSEMBLY 23 * 36" MMT9945 TAPE,REFLECTIVE,2" WIDE

12 1 1379950 INFEED ASSEMBLY

Page 90 Page

Page 96

Page

Page 89 Page

Page 95

Page

Page 107

Page

Page 94

Page

Page 83

Page

Page 51

Page

Page 118 Page

Page 53

Page

Page 84

Page

Page 52

Page

Page 109 Page

Page 111

Page

Page 110

Page

1379013 Laser Guard Assembly, 55 watt AAC Drawing Number 1379013 Rev 4

NO QTY PART # DESCRIPTION NO QTY PART # DESCRIPTION

1 3 1379-LAB5 LABEL, LASER SERVICE 10 1 EE07100SP072 CORD, FAN, 72" STRAIGHT

2 3 1379-LAB7 LABEL,NONINTERLOCK, 11 1 MM1976K78 FAN, COOLING, 230VAC

3 1 1379014 LASER BOX, LEFT SIDE 12 * 25" X 25" MM2069K93 FILTER, MEDIA, 25"x36' ROLL

4 1 1379015 LASER BOX, RIGHT SIDE 13 * 36 MM90058A829 SCREW, 10-32, TRI-GROOVE

5 1 1379016 LASER BOX, FRONT PNL ASM 14 10 NNE8-32 NUT,ELASTIC LOCK, 8-32

6 1 1379853 BRACKET, FRAME SUPPORT 15 8 WWF8 WASHER, FLAT #8

7 1 1379857 LASER GUARD WELDMENT 16 * 36 WWFS10 WASHER, FLAT #10

8 1 1379951 FAN EXHAUST WELDMENT 17 * 36 WWL10 #10 LW

9 1 1379986 BRACKET, FRAME SUPPORT




1 3 1379-LAB5 LABEL, LASER SERVICE 17 1 1379986 BRACKET, FRAME SUPPORT

2 3 1379-LAB7 LABEL,NONINTERLOCK, LASER 18 1 MM19155K29 GUARD, FAN

3 1 1379014 LASER BOX, LEFT SIDE 19 1 MM1976K29 FAN,280MM,1100CFM

4 1 1379015 LASER BOX, RIGHT SIDE 20 * 16" MM2069K93 FILTER, MEDIA, 25" X 36'

5 6 1379312 FILTER, LASER CABINET 21 * 12 MM90058A829 SCREW, 10-32, TRI-GROOVE

6 6 1379314 FILTER, GRILL, LASER BOX 22 4 SSBC98016 10-32 X 1/4 BUTTON CAP SC

7 1 1379319 FILTER BOX ASSEMBLY 23 * 30 SSHC01064 1/4-20 X 1 HHCS

8 2 1379322 FILTER, GRILL, LASER BOX 24 * 24 SSPP98032 10-32 X 1/2 PAN PHIL

9 1 1379323 BOX,SENSOR,DOOR 25 * 80 SSPS98024 10-32X3/8 PAN HD SLOT

10 1 1379325 LASER BOX, BACK SIDE 26 * 4 SSZS93048 SCREW, SHT.METAL 10 ZIP

11 1 1379326 LASER BOX, BACK PLATE 27 * 30 WWFS1/4 WASHER,FLAT,SAE,1/4

12 2 1379333 FILTER, GRILL, RF PWR SP 28 1 WWFS10 WASHER, FLAT, #10, SAE

13 1 1379472 PLATE, COVER, BULKHEAD 29 * 30 WWL1/4 WASHER,LOCK,1/4

14 1 1379853 BRACKET, FRAME SUPPORT 30 * 40 WWL10 WASHER,LOCK,#10

15 1 1379857 LASER GUARD WELDMENT 31 1 FFE6930A SWITCH,INTEROCK,DOOR,SPDT

16 1 1379976 LASER BOX, FRONT PNL ASM



1 3 1379-LAB5 LABEL, LASER SERVICE 17 1 1379986 BRACKET, FRAME SUPPORT

2 3 1379-LAB7 LABEL,NONINTERLOCK, LASER 18 1 MM19155K29 GUARD, FAN

3 1 1379014 LASER BOX, LEFT SIDE 19 1 MM1976K29 FAN,280MM,1100CFM

4 1 1379015 LASER BOX, RIGHT SIDE 20 * 16" MM2069K93 FILTER, MEDIA, 25" X 36'

5 6 1379312 FILTER, LASER CABINET 21 * 44 MM90058A829 SCREW, 10-32, TRI-GROOVE

6 6 1379314 FILTER, GRILL, LASER BOX 22 * 8 NNK10-32 KEP NUT, 10-32

7 1 1379319 FILTER BOX ASSEMBLY 23 * 30 SSHC01064 1/4-20 X 1 HHCS

8 1 1379323 BOX,SENSOR,DOOR 24 * 28 SSPP98032 10-32 X 1/2 PAN PHIL

9 1 1379325 LASER BOX, BACK SIDE 25 * 4 SSSC98032S 10-32 X 1/2 SOC CAP

10 1 1379326 LASER BOX, BACK PLATE 26 * 4 SSZS93048 SCREW, SHT.METAL 10 ZIP

11 1 1379462 LASER BOX, FRONT SIDE 27 * 30 WWFS1/4 WASHER,FLAT,SAE,1/4

12 2 1379469 FILTER, COVER, LASER BOX 28 *76 WWFS10 WASHER, FLAT #10

13 2 1379470 FILTER, COVER, RF PWR SP 29 * 30 WWL1/4 WASHER,LOCK,1/4

14 12 1379473 PLATE, NUT, LASER BOX 30 * 68 WWL10 #10 LW

15 1 1379853 BRACKET, FRAME SUPPORT 32 1 FFE6930A SWITCH,INTEROCK,DOOR,SPDT

16 1 1379857 LASER GUARD WELDMENT


1379153 Right Side Vent Hood Assembly AAC Drawing Number 1379153 Rev 3

NO. QTY PART # DESCRIPTION

1 3 1379065 BRACE,DUCT FITTING

2 1 1379099 HOOD PANEL, SIDE

3 1 1379100 COVER, EYE ACCESS

4 1 1379154 HOOD PANEL, TOP, RIGHT

5 1 1379898 HOOD PANEL, TOP


7 2 MMATT06 TAKE OFF,6"

8 1 MMATT06M TAKE OFF,6", MODIFIED

9 8 NNE8-32 NUT,ELASTIC LOCK, 8-32

10 22 SSPP90024 8-32X3/8 PAN PHLPS

11 4 SSPP90048 #8-32 X 3/4 PAN HD PHIL

12 32 WWF8 WASHER, FLAT #8

1379200 Generic Laser Workstation AAC Drawing Number 1379200 Rev 3


1 1 1379034 KEYBOARD TRAY ASM 12 1 1379795 STACKER FESTOON ASSEMBLY

2 1 1379044 MOUNT, LCD TOUCHSCREEN 13 1 1379825 CLAMP, STACKER RACK, RH

3 1 1379064 LASER WORKTOP ASSEMBLY 14 1 1379830 CLAMP, STACKER RACK, LH

4 1 1379101 ENCLOSURE, SAFETY SWITCH 15 1 1379850 LASER HEAD DRIVE ASSY

5 1 1379102 BRACKET, DOOR MAGNET 16 1 1379860 MAIN ROLLER ASSEMBLY

6 2 1379182 BRKT,MTG,EYE,UNIVERSAL 17 1 1379896 CONTROL SYSTEM ASSY

7 1 1379208 FRONT GUARD ASSEMBLY 18 1 1379935 STACKER SAFETY EYE ASSY

8 1 1379250 MAIN FRAME ASSEMBLY 19 4 1975-412A PLATE,NUT,4-40,.95CTC

9 1 1379266 REAR GUARD ASSEMBLY 20 2 98205010 BRKT,SENSOR,982A

10 1 1379457 PNEUMATIC PANEL ASSEMBLY 21 4 FFSM312LVQ EYE,ELECTRIC,10-30VDC

11 1 1379767 MATERIAL EDGE SENSOR ASSY

Page 56

Page

Page 54

Page Page 55

Page

Page 58 Page

Page 59

Page

Page 57 Page

Page 69 Page

Page 60

Page

Page 63

Page Page 65

Page Page 67 Page

Page 62

Page

Page 71

Page

Page 73 Page Page 75

Page


1379034 Keyboard Tray Assembly AAC Drawing Number 1379034 Rev 0


1 1 1379032 TRAY, KEYBOARD BASE

2 1 1379033 COVER, KEYBOARD TRAY

3 1 MM1568A45 HANDLE,DOOR,PULL

4 2 SSAS016025 1/4X38X10-32, SHOULDER SC

5 2 SSBC90032 #8-32 X 1/2 BUT HEAD

6 2 WWFF1/4 WASHER,FLAT,FELT

1379044 LCD Touchscreen Mount AAC Drawing Number 1379044 Rev 0


1 2 28201 CROSS BLOCK, LARGE

2 1 1379048 ARM, LCD MOUNT WELDMENT

3 1 1379053 MOUNT, LCD, WELDMENT

4 1 1379054 ROD,TILT, LCD SUPPORT

5 1 CCCL12F CLAMP COLLAR- 3/4

6 3 SSHC01032 1/4-20 X 1/2 HHCS

7 1 SSHC10040 5/16-18 X 5/8 HHCS

8 2 TTH32425 HANDLE,THRDED,5/16-18X3/4

9 2 WWFE016 WASHER,FENDER,LARGE,1/4


1379064 Laser Worktop Assembly AAC Drawing Number 1379064 Rev 1


1 1 1379018 PLATE, WORKTOP

2 2 1379030 PLATE, SPACER

3 1 1379062 CABLE GLAND

4 1 1379063 PLATE, CABLE GLAND

5 * 66" MM8507K22 EDGE TRIM

6 4 SSFC01032 1/4-20 X 1/2 FLAT ALLEN

7 4 SSFC98024 #10-32 X 3/8 FLAT ALLEN

1379101 Safety Switch Enclosure AAC Drawing Number 1379101 Rev 0


1 1 EEPCB65GM5 ENCLOSURE,SLOTS, 2 SIDES

2 *1 FF248-502 TERMBLK,WAGO,TP,MARKER 1-10

3 *1 FF248-503 TERMBLK,WAGO,TP,MARKER 11-20

4 16 FF264-311 TERMBLK,WAGO,TOP,SINGLE,GRY

5 1 FF264-371 TERMBLK,WAGO,TOP,END

6 1 FF264-3BKT9 MOUNT,WAGO TERMINAL,3.7L

7 2 WWB5/32 WASHER,BRASS,5/32ID


1379208 Front Guard Assembly AAC Drawing Number 1379208 Rev 2


1 6 1379-LAB6 LABEL, INTERLOCK, LASER 12 1 1379682 WLDMT,GUARD,FRONT

2 2 1379087 STAND OFF, GUARD 13 1 1379995 GUARD, COVER, LH, FRONT

3 6 1379155 PLATE, SPACER, HINGE 14 3 EECMS221PC5 SWITCH,SAFETY,CODED,INTLK

4 1 1379197 GUARD, COVER, RHF & LHR 15 2 MM1568A45 HANDLE,DOOR,PULL

5 2 1379213 PLATE, SUPPORT, GUARD ROL 16 * 4 SSPP90032 #8-32 X 1/2 PAN HD PHIL

6 2 1379214 PLATE, NUT, SAFETY SENSOR 17 * 6 SSPP98024 #10-32 X 3/8 PAN HD PHIL

7 2 1379215 PLATE, WASHER, HANDLE 18 * 33 SSPP98032 #10-32 X 1/2 PAN HD PHIL

8 1 1379216 PLATE, WASHER, ROLL GUARD 19 * 6 SSPP98080 #10-32 X 1-1/4 PAN HD PHIL

9 1 1379217 PLATE, NUT, ROLL GUARD 20 * 21 WWFS10 WASHER, FLAT #10

10 1 1379218 GUARD, ROLLER COVER 21 * 2 WWL8 #8 LW

11 1 1379219 GUARD, ROLLER COVER

1379266 Rear Guard Assembly AAC Drawing Number 1379266 Rev 2


1 6 1379-LAB6 LABEL, INTERLOCK, LASER 12 1 1379220 GUARD, COVER, RH, REAR

2 2 1379087 STAND OFF, GUARD 13 1 1379684 WLDMT,GUARD,REAR

3 6 1379155 PLATE, SPACER, HINGE 14 3 EECMS221PC5 SWITCH,SAFETY,CODED,INTLK

4 1 1379197 GUARD, COVER, RHF & LHR 15 2 MM1568A45 HANDLE,DOOR,PULL

5 2 1379213 PLATE, SUPPORT, GUARD ROL 16 4 SSPP90032 #8-32 X 1/2 PAN HD PHIL

6 2 1379214 PLATE, NUT, SAFETY SENSOR 17 6 SSPP98024 #10-32 X 3/8 PAN HD PHIL

7 2 1379215 PLATE, WASHER, HANDLE 18 * 33 SSPP98032 #10-32 X 1/2 PAN HD PHIL

8 1 1379216 PLATE, WASHER, ROLL GUARD 19 6 SSPP98080 #10-32 X 1-1/4 PAN HD PHIL

9 1 1379217 PLATE, NUT, ROLL GUARD 20 21 WWFS10 WASHER, FLAT #10

10 1 1379218 GUARD, ROLLER COVER 21 2 WWL8 #8 LW

11 1 1379219 GUARD, ROLLER COVER 22 10 SSPP98032 10-32 X 1/2 PAN PHIL


1379457 Pneumatic Panel Assembly AAC Drawing Number 1379457 Rev 4


1 1 0411-071 BRKT,REGULATOR 26 1 AAV125B PILOT VALVE

2 1 1379042 MTG BRKT, TOGGLE VALVE 27 1 AAV41V VALVE,TOGGLE

3 1 1379060 BANK, FLOW CONTROL 28 1 AAVBG35 GUN,BLOW

4 1 1379370 PNEUMATIC PANEL 29 1 AAVBG35D HOSE, COIL, 25FT, 1/4" OD

5 1 1379581 VALVE STACK ASSY 30 1 AAVF51FM1B AIR/ELEC PRESSURE SW

6 * 1 1379-LAB14 LABELS, PNUEMATICS 31 1 AAVS125 SHUTTLE VALVE,1/8"PORT

7 * 10 1391160 CABLE ASSY,VALVE,DIN,3M 32 2 MM4554K12 PLUG, 1/4" PIPE

8 1 AA198-503 0-30PSI AIR GAGE 1/8NPT 33 2 NNH6-32 NUT,HEX,6-32

9 3 AA198-5032 0-60PSI AIR GAGE 1/8NPT 34 4 SSSC01016S 1/4-20 X 1/4 SOC CAP SC

10 3 AA198-503A REG,0-30 W/GAUGE& BRKT, REL'G 35 2 SSSC70024 4-40 X 3/8 SOCKET CAP

11 1 AA198-5118 AIR PREP COMBO, LASER 36 6 SSSC80064 6-32 X 1 SOC CAP SC

12 1 AA198-RP3 REGULATOR,PRECISION AIR 37 2 SSSC80080 6-32 X 1-1/4 SOC CAP SC

13 1 AA2201-07 FLOW CONTROL,1/4TX1/4NPT 38 4 SSSC90080 #8-32 X 1-1/4 SOC CAP SC

14 3 AAE4V21008 VALVE, 1/4" PORTED, 24VDC 39 17 SSSC98024 10-32 X 3/8 SOC CAP

15 4 AAFP18 MUFFLER,1/8 NPT, BRONZ 40 16 WWB10S WASHER,BRASS,10,SMALL

16 1 AAQBT-5-10 QUICK BRANCH "T" 41 2 WWF4 WASHER, FLAT, #4

17 1 AAQMC-4-4 QUICK MALE CONN 1/4 X 1/4 42 4 WWFS1/4 WASHER,FLAT,SAE,1/4

18 4 AAQMC-4-8 QUICK MALE CONN,1/4X1/8 43 2 WWFS6 WASHER, FLAT, #6

19 3 AAQME-2-3 MALE ELBOW 1/2 OD TUBE 44 4 WWL1/4 WASHER,LOCK,1/4

20 1 AAQME-3-3 MALE ELBOW 3/8 OD TUBE 45 17 WWL10 WASHER,LOCK,#10

21 13 AAQME-4-4 ELBOW, MALE,1/4X1/4NPT 46 2 WWL4 WASHER,LOCK,#4

22 6 AAQME-4-8 ELBOW,QUICK MALE,1/4X1/8 47 2 WWL6 WASHER,LOCK,#6

23 2 AAQME-5-4 ELBOW, MALE 5/32X1/4NPT 48 4 WWL8 WASHER,LOCK,#8

24 2 AAQPP-07 QUICK PLUG 1/4 49 8 WWSI6 WASHER,INT. TOOTH

25 3 AAQUT-3-3 QUICK UNION T 3/8X3/8

Page 61 Page

1379581 Valve Stack Assembly AAC Drawing Number 1379581 Rev 0


1 1 AAE4V200M6 MANIFOLD, 6 STATION

2 1 AAE4V200MB MANIFOLD, BLANK PLATE

3 4 AAE4V21008 VALVE, 1/4" PORTED, 24VDC

4 1 AAE4V230C08 VALVE, 1/4" PORTED, 24VDC

5 4 AAFP28 MUFFLER,1/4 NPT

6 2 AAQMC-3-4 QUICK MALE CONNECTOR

7 8 AAQME-4-4 ELBOW, MALE,1/4X1/4NPT

8 2 MM4554K12 PLUG, 1/4" PIPE


1379767 Material Edge Sensor Assembly AAC Drawing Number 1379767 Rev 2


1 2 1379007 SPROCKET,1/4P,18T,1/4B 17 2 MMGNR12R0250HN RAIL,LINEAR,MG12 SERIES

2 1 1379238 ROD,MTG,EDGE DETECT 18 2 RRCS062-L4 SPRING, WAVE FLAT WIRE

3 1 1379267 ROD,MTG,EDGE DETECT.L 19 4 SSSC70024 #4-40 X 3/8 SOC CAP

4 2 1379762 BLOCK, SENSOR MOUNT 20 8 SSSC70040 #4-40 X 5/8 SOC CAP

5 1 1379768 MOUNT, DRIVEN SPROCKET 21 4 SSSC70048 #4-40 X 3/4 SOC CAP

6 1 1379769 SHAFT, IDLER SPROCKET 22 2 SSSC80024 #6-32 X 3/8 SOC CAP

7 1 1379772 MOUNT, DRIVE SPROCKET 23 6 SSSC98032 #10-32 X 1/2 SOC CAP

8 1 1379773 MTG BRKT, POINTER 24 4 SSSC98040 #10-32 X 5/8 SOC CAP

9 1 1379817 EDGE GUIDE POINTER 25 8 SSSCM3X12 M3-0.5X12 ,SOCKET CAP

10 1 1379828 CHAIN SUPPORT 26 1 TTK32315 KNOB,1-7/8OD,3/8B,BLACK

11 2 23132A HOLDER, EYE 27 1 UUFF520-09 BRG,BRONZE,.3765ID

12 1 33006114 SHAFT, ADJUSTMENT KNOB 28 2 WWFS10 WASHER, FLAT #10

13 4 FF89F2608 SPACER,ALUMINUM,3/8 29 2 WWFS6 WASHER, FLAT, #6

14 2 FFSM312LVQ EYE,ELECTRIC,10-30VDC 30 6 WWL10 #10 LW

15 * 198.25"MM25 #25 RIVET CHAIN 31 2 WWL6 WASHER,LOCK,6

16 2 MMGN12HZ0HN MGN12H BEARING BLOCK 32 4 WWSI4 WASHER,INT. TOOTH

1379795 Stacker Festoon Assembly AAC Drawing Number 1379795 Rev 1

NO. QTY PART# DESCRIPTION NO. QTY PART# DESCRIPTION

1 2 1379531 STAND-OFF, MATERIAL 15 4 AAQBT-5-10 QUICK BRANCH "T"

2 2 1379782 PLATE, SIDE, FUNNEL 16 4 AAQME-5-8 QUICK MALE ELBOW

3 2 1379783 MOUNT, FUNNEL PIVOT 17 2 BBAW-5Z BEARING,ROD END,FEMALE

4 2 1379785 SHAFT, FUNNEL PIVOT 18 2 BBS8703-88 BEARING,BALL,.75IDX1.75OD

5 1 1379789 DEFLECTOR, FUNNEL 19 2 NNK1/4-20 NUT,HEX,KEP,1/4-20,W/LOCK

6 2 1379791 MOUNT, FUNNEL 20 8 SSBC98024 #10-32 X 3/8 BUT HEAD

7 2 1379794 BRACKET, PIVOT DRIVE 21 8 SSFC01032 1/4-20 X 1/2 FLAT ALLEN

8 1 1379819 MATERIAL GUIDE- OUTSIDE 22 4 SSHC98096 #10-32 X 1-1/2 HEX CAP

9 1 1379821 MATERIAL GUIDE INSIDE PLT 23 4 WWF10 WASHER, FLAT, #10, COM

10 2 AACCM096-DXP CYLINDER,AIR,DA,W/MAGN 24 4 WWFS1/2 WASHER, FLAT, 1/2

11 2 AAEHSKQ SWITCH,HALL EFFECT BIMBA 25 4 WWL10 WASHER,LOCK,#10

12 4 AAF01 SOFFIE JET W/40MM EXT 26 2 WWL5/16 5/16 LW

13 2 AAFBP-11C BRKT,PIVOT,1/4 BORE 27 4 SSSC10064 5/16-18 X 1 SOC CAP

1379825 RH Stacker Rack Clamp AAC Drawing Number 1379825 Rev 0


1 1 1379811 PLATE, CLAMP ARM

2 1 1379812 SPACER, CYLINDER PIVOT

3 1 1379813 GUIDE, UPPER NESTING

4 1 1379815 PLATE, LEFT CLAMP

5 1 1379816 ARM, LEFT CLAMP

6 2 AA198RA508 FLOW CONTROL,5/32 X 1/8"

7 1 AAC6DP-4 CYLINDER,AIR,DA

8 1 BBAW-5Z BEARING,ROD END,FEMALE

9 2 BBNTA411 BEARING,THRUST,.250B

10 2 BBNTA613 BEARING,THRUST,375BORE

11 4 BBTRA411 WASHER,THRUST,STEEL

12 4 BBTRA613 WASHER,THRUST,STL, .375B

13 1 MM9540K28 BUMPER, 1-1/2 DIA, 70A

14 1 NNH3/8-16 3/8-16 HEX NUT

15 1 NNJ5/16-24 5/16-24 HEX JAM NUT

16 2 NNK1/4-20 NUT,HEX,KEP,1/4-20,W/LOCK

17 2 SSHC01048 1/4-20 X 3/4 HEX HEAD

18 1 SSHC01056 1/4-20 X 7/8 HEX HEAD

19 1 SSHC01096 1/4-20 X 1-1/2 HEX HEAD

20 1 SSHC25080 3/8-16 X 1-1/4 HEX HEAD

21 2 SSSC01024 1/4-20 X 3/8 SOC CAP

22 1 SSSC10064 5/16-18 X 1 SOC CAP

23 2 WWFS1/4 WASHER FLAT, 1/4

24 2 WWFS5/16 WASHER, FLAT, 5/16

25 2 WWL1/4 1/4 LW

26 1 WWL5/16 5/16 LW

1379830 LH Stacker Rack Clamp AAC Drawing Number 1379830 Rev 0


1 1 1379809 PLATE, RIGHT CLAMP

2 1 1379810 ARM, RIGHT CLAMP

3 1 1379811 PLATE, CLAMP ARM

4 1 1379812 SPACER, CYLINDER PIVOT

5 1 1379813 GUIDE, UPPER NESTING

6 2 AA198RA508 FLOW CONTROL,5/32 X 1/8"

7 1 094-DP CYLINDER,AIR,DA

8 1 BBAW-5Z BEARING,ROD END,FEMALE


10 2 BBNTA613 BEARING,THRUST,375BORE


12 4 BBTRA613 WASHER,THRUST,STL, .375B

13 1 MM9540K28 BUMPER, 1-1/2 DIA, 70A

14 1 NNH3/8-16 3/8-16 HEX NUT

15 1 NNJ5/16-24 5/16-24 HEX JAM NUT

16 2 NNK1/4-20 NUT,HEX,KEP,1/4-20,W/LOCK

17 2 SSHC01048 1/4-20 X 3/4 HEX HEAD

18 1 SSHC01056 1/4-20 X 7/8 HEX HEAD

19 1 SSHC01096 1/4-20 X 1-1/2 HEX HEAD

20 1 SSHC25080 3/8-16 X 1-1/4 HEX HEAD

21 2 SSSC01024 1/4-20 X 3/8 SOC CAP

22 1 SSSC10064 5/16-18 X 1 SOC CAP


24 2 WWFS5/16 WASHER, FLAT, 5/16

25 2 WWL1/4 1/4 LW

26 1 WWL5/16 5/16 LW

1379850 Laser Head Drive Assembly AAC Drawing Number 1379850 Rev 3


1 1 1321482 FLOATING COUPLING 36 * 3 MMABP-5-S SLOT COVER

2 1 1379231 GEAR,STEEL,25T,13DP 37 1 MMADS10-8MM-1/2 COUPLING, 8MM

3 1 1379247 GAUGE, LASER SETUP 38 1 MMAE070003N34 GEARHEAD

4 1 1379252 WRENCH, LASER SPUR 39 2 MMHWS-18/25-M8 BRACKET,SENSOR

5 2 1379263 TRACK MTG ANGLE 40 2 MMLC15C1 BLOCK,BEARING

6 1 1379354 MOTOR SPACER PLT- X 41 1 MMLWL15R300 RAIL,LINEAR,15MM

7 1 1379842 GEAR,PLASTIC,25T,13DP 42 4 MMNSTL-25 SLOT NUT

8 1 1379843 MTG PLT, LASER HEAD 43 2 MMSIEN-M8B-NSM PROX SWITCH,10

9 1 1379848 MTG PLT, LASER HEAD 44 2 NNH10-32 #10-32 HEX NUT

10 1 1379854 MTG PLT, X-AXIS MOTOR 45 1 SGMAH04AAF41 MOTOR,SERVO,.4K

11 2 1379858 BRKT, LASER HEAD 46 8 SSBC70024 #4-40 X 3/8

12 2 1379861 CLAMP, LASER HEAD 47 4 SSFC90024 #8-32 x 3/8 FLAT

13 2 1379863 FLAG, PROX SENSOR 48 4 SSFC98040 #10-32 X 5/8 FLAT

14 1 1379868 CHANNEL, TRACK 49 4 SSFC98080 #10-32 X 1-1/4 FLAT

15 2 1379870 LASER PROCESS HEAD 50 12 SSFCM4X10 M4-0.7 X 10 FLAT

16 1 1379873 MTG PLT, LASER HEAD 51 4 SSFCM5X10 M5-0.8X10 FLAT

17 1 1379874 MTG BRKT, SHIFT CYLIN 52 4 SSSC90024 #8-32 X 3/8 SOC

18 1 1379875 BRACKET, SHIFT CYL 53 4 SSSC90032 #8-32 X 1/2 SOC

19 1 1379885 MTG PLT, LASER HEAD 54 2 SSSC90064 #8-32 X 1 SOC CAP

20 1 1379886 MTG SPACER, LASER 55 2 SSSC98024 #10-32 X 3/8 SOC

21 2 1379887 WASHER, BUMPER 56 4 SSSC98032 #10-32 X 1/2 SOC

22 2 1379889 MTG BRKT, CABLE TRACK 57 2 SSSC98040 #10-32 X 5/8 SOC

23 4 1379890 MTG BRKT, LINEAR DRIVE 58 4 SSSC98048 #10-32 X 3/4 SOC

24 2 1379891 MTG BRKT, LINEAR DRIVE 59 6 SSSCM3X6 M3-0.5 X 6 SOC

25 1 1379893 MTG BRKT, LIMIT 60 4 SSSCM3X10 M3-0.5 X 10 SOC

26 1 AACE16D8N CYLINDER,AIR,DA,5/8B 61 8 SSSCM4X20 M4-0.7 X 20 SOC

27 1 AAQME-5-10 ELBOW, MALE,5/32X10 62 13 SSSCM5X10 M5-0.8 X 10 SOC

28 1 DGE251200ZRLKRB LINEAR DRIVE 1200MM 63 1 SSSCM5X16 M5-0.8 X 16 SOC

29 1 DGE251200ZRLVRK LINEAR DRIVE 1200MM 64 2 WWF8 WASHER, FLAT #8

30 1 FFGLLA01A1B SWITCH, LIMIT, ROLLER 65 6 WWFS10 WASHER, FLAT #10

31 1 FFM4518 STRAIN RELIEF,LIQ TIGHT 66 10 WWL8 #8 LW

32 1 MM8226T13 MUFFLER, EXHAUST 67 10 WWL10 #10 LW

33 2 MM9540K53 BUMPER, 3/4 DIA

34 2 MM6202680 TRANTORQUE COUPLING

35 2 MM18222844 DUCT,WIRE MICROTRAK


1379870 Laser Process Head, 55 Watt AAC Drawing Number 1379870 Rev 1


1 1 1379066 BEAM TUBE 68MM-COLLIMATOR

2 1 1379132 LASER TIP, LARGE

3 1 210CM28030X45FS MIRROR,1.1"X3MM CO2

4 1 210CV28040095ZS LENS,1.1"X3.75" F.L.

5 2 AAQME-5-10 ELBOW, MALE,5/32X10-32

6 1 BBK1928030NN BEAM BENDER, 19MM C.A.

7 1 LAM-19-25-MAN MANUAL LINEAR ADJ MOUNT

8 1 PHA1928095SB LASER PROCESS HD ASSY

1379935 Stacker Safety Eye Assembly AAC Drawing Number 1379935 Rev 1


1 1 1379924 MTG BRKT, SAFETY EYES

2 2 1975-412A PLATE,NUT,4-40,.95CTC

3 2 AAQMC-4-8 QUICK MALE CONN,1/4X1/8

4 2 AAQMC-5-8 QU. MALE CONN 5/32X1/8

5 2 AAQME-4-8 ELBOW,QUICK MALE,1/4X1/8

6 1 AAQPP-07 QUICK PLUG 1/4

7 2 AAV41V VALVE,TOGGLE

8 2 FFSM312LVQ EYE,ELECTRIC,10-30VDC

9 4 SSSC70048 #4-40 X 3/4 SOC CAP

10 4 WWSI4 WASHER,INT. TOOTH

1379860 Main Roller Assembly AAC Drawing Number 1379860 Rev 11


1 3 1379-LAB6 LABEL, INTERLOCK, LASER 37 1 1379869 BOTTOM COVER

2 1 1379071 CLOTH SUPPORT ASSY 38 2 1379888 BRKT, ANTI-ROTATE

3 1 1379072 CLOTH SUPPORT ASSY 39 1 1379944 TUBE, HANDLE

4 1 1379112 STRIPPER, ROLLER 40 1 32004018 SLEEVE, ROD END

5 1 1379118 BRACE,DUCT FITTING 41 1 AA198RA408 FLOW CONTROL,1/4

6 3 1379196 PLATE, SAFETY SW 42 1 AAC175DPM CYLINDER,AIR,DA

7 1 1379224 ROLLER, PINCH ADJUST 43 2 AACDM2E25646 CYLINDER, 25B

8 1 1379227 PLATE, WASHER 44 4 AAEHSKQ SWITCH,HALL

9 2 1379229 PLATE, BEARING SHIM 45 2 AAFBM2025 BAND MOUNT

10 1 1379262 TOP PINCH ROLLER ASM 46 2 AAFCME020B REAR PIVOT

11 1 1379273 SUPPORT TUBE - LH 47 1 AAFD-229 BRKT, PIVOT, 3/8

12 4 1379274 MTG ANGLE DRIVE 48 2 AAFD35000 BAND,17 CYLINDER

13 1 1379275 BEARING MTG PLATE 49 2 AAFP18 MUFFLER,1/8 NPT

14 1 1379276 SHAFT, DRIVE ROLLERS 50 2 AAQMC-4-8 QUICK MALE CONN

15 2 1379278 SHAFT, DRIVE ROLLERS 51 4 AAQME-4-8U QUICK MALE ELBOW

16 4 1379284 SHAFT, IDLER ROLLERS 52 1 BBAW-7 BEARING,ROD

17 1 1379285 BEARING MTG PLATE 53 2 BBAWM10Z ROD END, SPHERIC

18 4 1379293 PIVOT BLOCK-TOP 54 8 BBS8703-88 BEARING,BALL

19 1 1379340 SUPPORT TUBE - RH 55 1 CCSCL7F CLAMP COLLAR

20 1 1379359 GUARD, Y AXIS BELT, 56 3 EECMS221PC5 SWITCH,SAFETY

21 1 1379360 GUARD, Y AXIS BELT, TOP 57 1 GG38AT10780BFX 38MM WIDE BELT

22 3 1379406 DRIVE ROLLER ASSEMBLY 58 1 MM1766K874 ADJ. DUCT ELBOW

23 2 1379442 PIVOT ARM WELDMENT 59 1 MMATT06M TAKE OFF,6"

24 2 1379447 PIVOT ARM WELDMENT 60 3 MMVPS-112 BEARING,PILLOW

25 2 1379534 ROLLER LIFT CYLINDER 61 1 NNE10-32 NUT,ELASTIC LOCK

26 1 1379537 CLUTCH ASSY, REAR FEED 62 2 NNJ10-32 NUT,JAM,THIN #10

27 1 1379538 SHAFT, DRIVE ROLLERS 63 1 NNJ5/16-24 NUT,JAM,5/16-24

28 1 1379542 STRIPPER, SHIM 64 1 NNJ7/16-20 NUT,JAM,7/16-20

29 1 1379572 Y-AXIS MOTOR ASSY 65 8 SSPS98024 10-32X3/8 PAN HD

30 1 1379582 PULLEY, DRIVE ROLLER, Y 66 1 SSSC01024 1/4-20 X 3/8 SOC

31 1 1379610 BOTTOM COVER 67 1 SSSC20080 5/16-24X1-1/4, SOC

32 2 1379766 STACKER CLAMP CYL 68 6 SSSC98032S 10-32 X 1/2 SOC

33 1 1379798 BRKT, R FNT. ROLLER LIFT 69 5 WWFS10S WASHER,FLAT,#10

34 1 1379802 BLOWER TUBE, STACKER 70 2 WWFS5/16 WASHER,FLAT,SAE

35 1 1379837 HANDLE, REAR PIVOT 71 4 WWL10S WASHER,LOCK,#10

36 1 1379844 BRKT, L. FNT. ROLLER LIFT

1379896 Control System Assembly AAC Drawing Number 1379896 Rev 16


1 1 * 1379-CAB2 CABLE PKG , CONTROL 34 * 32" EEPN05L08V RACEWAY, PVC

2 1 1379-COMP2 COMPUTER, PACKAGE 35 1 EEPT1510MX LCD, TOUCHSCREEN

3 1 1379-LAB8 LABEL, INDENTIFICATION 36 1 EESD2GP DISCONNECT PE,80A

4 1 * 1379-LAB13 LABEL, FDA COMPLIANCE 37 1 EESD2080RR DISCONNECT, 3 POL

5 1 1379001 SUBPANEL,LASER 38 1 EESDHRY DISCONNECT

6 1 1379055 SHELF, PC 39 1 EESGDS04A12A AMPLIFIER, SERVO

7 1 1379080 PENDANT, ASSY, LASER 40 1 EESGDS08A12A AMPLIFIER, SERVO

8 1 1379098 START/STOP ASSY 41 1 EESR103AM01 SAFETY RELAY

9 1 1379181 SWITCH,MASTER 42 61" EETS35X7.5A DIN RAIL-AMERICAN

10 * 1 1379233 DISCONNECT, SHAFT 43 4 FF280-308 TERMBLK ENDPLAT

11 1 1379952 WIRE STRAIN RELIEF RAIL 44 19 FF280-402 JUMPER,WAGO,TOP

12 1 1379963 CONTROL BOX CABINET 45 41 FF280-901 TERMBLK,WAGO

13 8 AAF3/16 CLAMP, BLACK PLASTIC 46 6 FF280-907 TERMBLK,WAGO

14 1 EE861SSR115 RELAY,SOLID STATE,DC 47 6 FF3460 STRAIN RELIEF,LIQ

15 1 EE07100SP072 CORD, FAN, 72" 48 1 FF8465 NUT,LOCK,3/4NPT

16 1 EE64151B FERRITE CORE,SPLIT 49 * 1 FF0808749-0001 MARKER STRIP

17 1 EE2861632 INLINE BLOCK,PWM 50 * 1 FF0808749-0011 MARKER STRIP

18 2 EE2863520 INLINE BLOCK,16 IN 51 * 1 FF0808749-0021 MARKER STRIP

19 3 EE2863546 INLINE BLOCK,8 OUT 52 * 30' FF822329 CABLE,SOOW,3X10A

20 1 EE2884619 INLINE BUS COUPLER 53 * 150 FFLS11427 LABEL,BRADY,TLS20

21 1 EECA491024 CONTACTOR, MINI, 240V 54 1 FFMD60241 POWER SUPPLY

22 8 EECLIPFIX ANCHOR,DIN RAIL 55 2 FFQL213DMKM02 CIRCUIT BREAKER

23 1 EEJEPMCCM2300 COMM CARD,RS232 56 2 FFQL213DMKM10 CIRCUIT BREAKER

24 1 EEJEPMCMP2300 CONTROLLER, MOTION 57 1 FFQL213DMKM15 CIRCUIT BREAKER

25 * 2 EEJEPMCOP300 RAIL CLIP,MP2300 58 3 FFQL213DMKM20 CIRCUIT BREAKER

26 2 EEJEPMCOP2300 SLOT COVER 59 2 FFRAV781BW MODULE, TVS, 240

27 1 EEJEPMCW6022 TERMINATION,BLOCK 60 1 MM100-1/8 DOOR TRIM - BLACK

28 1 EEL237228 KEYBOARD, USB 61 1 MM1976K78 FAN, COOLING

29 1 EEL237808 MOUSE, USB, OPTICAL 62 1 MM9307K69 GROMMET,5/8,1.12

30 1 EELES302RAGM1 TOWER, SIGNAL, LED 63 1 MM69915K72 STRAIN RELIEF, LIQ

31 1 EEMC85A22AC CONTACTOR,IEC,230VAC 64 * 156" MMLSSBB01210 FOAM, URETHANE

32 6 EEP18524DC RELAY, INTERFACE 24VD 65 1 MMSL208S DRIVE, VAR, FREQ

33 * 1 EEPN05F17V RACEWAY, ELBOW, PVC


1379071 Right Cloth Support Assembly AAC Drawing Number 1379071 Rev 3


1 1 1379068 MTG PLATE-LASER SLIT CHAN

2 1 1379228 MTG PLATE- LASER SLIT

3 1 1379245 PLATE, SLAG, ALTERNATE

4 1 1379265 SHIM, SPACER, CLOTH PLATE

5 2 1379279 SUPPORT RAIL


7 1 1379620 EXHAUST CHAMPER END PLATE

8 3 SSFC70016 4-40 X 1/4 FLAT SOC CAP

1379072 Left Cloth Support Assembly AAC Drawing Number 1379072 Rev 3



2 1 1379240 BRACKET, CHANNEL SUPPORT

3 1 1379245 PLATE, SLAG, ALTERNATE

4 1 1379265 SHIM, SPACER, CLOTH PLATE

5 2 1379279 SUPPORT RAIL

6 1 1379281 MTG PLATE- LASER SLIT


8 1 1379620 EXHAUST CHAMPER END PLATE

9 3 SSFC70016 4-40 X 1/4 FLAT SOC CAP

10 4 SSFC98040S #10-32 X 5/8 FLATALLEN,SS


1379224 Pinch Adjust Roller Assembly AAC Drawing Number 1379224 Rev 0


1 1 1379116 ROLLER, .50ID,1.5OD

2 1 1379225 MOUNT, ROLLER

3 1 1379226 SHAFT, ROLLER

4 2 BB1L038 BEARING,BALL,.375B

5 2 SSSS95008 #10-24 X 1/2 KNURL PT

1379534 Roller Lift Cylinder Assembly AAC Drawing Number 1379534 Rev 2


1 1 1379369 MTG BRKT, ROLLER LIFT CYL

2 1 AACDM2E25646 CYLINDER, 25B, 3 POS, 6S+46S

3 1 AAFCME020B REAR PIVOT FOR CM225 CYL SMC

4 1 AAFP18 MUFFLER,1/8 NPT, BRONZ

5 2 AAQME-4-8U QUICK MALE ELBOW,1/4X1/8

6 1 BBAWM10Z ROD END, SPHERICAL 10MM I

7 1 RRLC067GH-4 COMP. SPRING

8 2 WWFS3/8 WASHER,FLAT, 3/8

9 2 WWL1/4 WASHER,LOCK,1/4

10 2 SSHC01032 1/4-20 X 1/2 HHCS


1379572 Y-Axis Motor Assembly AAC Drawing Number 1379572 Rev 0


1 1 1379356 MTG. BRKT. Y AXIS MOTOR

2 1 1379357 MTG. PLATE. Y AXIS MOTOR

3 1 1379575 PULLEY - Y-AXIS MOTOR DRIVE

4 1 MMAE090010 GEARHEAD, PLANETARY 10:1

5 1 SGMPH08AAE41D MOTOR,SERVO,.75KW

6 4 SSFCM6X16 M6 X 20 FLAT ALLEN

7 4 SSHC01040 1/4-20 X 5/8 HHCS

8 4 WWF10 WASHER, FLAT, #10, COM


1379766 Stacker Clamp Cylinder Assembly AAC Drawing Number 1379766 Rev 2


1 1 1379121 CLAMP, STACKER BLOWER

2 1 1379605 MOUNT, STACKER CLAMP BRKT

3 1 AAC7DP-8 CYLINDER,AIR,DA

4 1 AAFF-11 FOOT MOUNT

5 2 AAQME-5-8 QUICK MALE ELBOW

6 1 MM9546K82 BUMPER,NEOPRENE 3/4 DIA

7 1 NNJ1/4-28 NUT, HEX, JAM, 1/4-28

8 3 SSSC01040 1/4-20 X 5/8" SOC CAP SC

9 2 SSSC90040 8-32 X 5/8 SOC CAP SC

10 2 WWF8 WASHER, FLAT, #8



1379883 Rear Feed Clutch Assembly AAC Drawing Number 1379883 Rev 2


1 1 1379397 WASHER, THRUST CAPTIVE

2 1 1379877 PULLEY, DRIVE ROLLER, Y-AXIS

3 1 1379879 BUSHING, ADAPTER,CLUTCH

4 1 1379966 STEM MOUNT, DRIVE CUP

5 1 1379982 KEY,5MM X8MM X 1.36



8 1 MM231572 COUPLING

9 1 MM231631M1 CLUTCH

10 1 MMSH-118 RING,SNAP,EXT.1.188S,

11 4 SSFCM6X12 SCREW,FLAT ALLEN CAP

12 4 SSSS01012 1/4-20X3/16 KNURL PT

13 2 UUFF838-1 BEARING,BRONZE,.751ID

1379211 Roll Mandrel Assembly, 1.5” core AAC Drawing Number 1379211 Rev 0


1 1 1379056 MANDREL, ROLL, 1.5 OD

2 2 1379148 CLAMP,ROLL,1.5 ID,3" OD

3 2 CCCL24F COLLAR,CLAMP,1.5 BORE


1379212 Roll Mandrel Assembly, 3” core AAC Drawing Number 1379212 Rev 0


1 2 1379210 CLAMP, ROLL,FLTD,2" CORE

2 1 1379991 MANDREL, ROLL, 2.0 OD

3 2 CCCL24F COLLAR,CLAMP,1.5 BORE

1379234 Laser Sub Assembly, 55W AAC Drawing Number 1379234 Rev 3


1 1 1379041 BASE MTG PLATE, LASER

2 * 1 1379094 CABLE ASSY, LASER POWER 55W

3 1 1379222 SUPPORT, COLLIMATOR BRKT

4 1 1379223 SUPPORT, COLLIMATOR-BEAM

5 4 1379232 LASER MTG BRKT

6 2 1379388 POWER SUPPLY MTG BRKT

7 1 1379600 MODULE, LASER INTERFACE

8 2 1379776 MTG ANGLE- FIRST MIRROR

9 1 1379871 COLLIMATOR, ASSY, 55W

10 1 EEC55A LASER, 55W DIAMOND C55A

11 1 FF3234 STRAIN RELIEF,LIQ TIGHT

12 2 FF8463 NUT,LOCK,1/2NPT,NYLON,BLK


14 2 FFM4518 STRAIN RELIEF,LIQ TIGHT

15 1 FFRSP150048 POWER SUPLY, 48V,32A,UNIV INPUT

16 4 NNH10-32 #10-32 HEX NUT

17 4 SSSS98032 #10-32 X 1/2 KNURL PT

Page 97

Page

1379878 Laser Sub Assembly, 100 Watt AAC Drawing Number 1379878 Rev 6


1 1 1379041 BASE MTG PLATE, LASER

2 1 1379141 PLATE,PS MOUNT

3 2 1379147 PLATE,PS TOP MOUNT

4 1* 1379204 CABLE ASSY,LASER POWER

5 1 1379222 SUPPORT, COLLIMATOR BRKT

6 2 1379223 SUPPORT, COLLIMATOR-BEAM

7 1 1379303 LASER FAN SHROUD ASSEMBLY

8 1 1379334 RF FAN SHROUD ASSEMBLY

9 1 1379608 TRANSITION TUBE, LASER

10 1 1379609 TUBE, BEAM DELIVERY

11 1 1379700 LASER INTERFACE,PCB ASSY

12 2 1379776 MTG ANGLE- FIRST MIRROR

13 4 1379827 BRACKET, MOUNT, PS

14 1 1379872 COLLIMATOR, ASSY, 100W

15 4 1379881 SPACER, BLOCK, LASER

16 4 1379884 BRACKET, MOUNT, LASER

17 1 CCCL14F COLLAR,7/8" CLAMP TYPE

18 1 EE7133314 CONNECTOR, RF, RT ANGLE

19 1 FF3234 STRAIN RELIEF,LIQ TIGHT



22 2 FFM4518 STRAIN RELIEF,LIQ TIGHT

23 2 FFRSP150048 POWER SUPLY, 48V,32A,UNIV INPUT

24 1 GEM100A 100W C02 LASER W/POWER

25 8 SSHC01040 1/4-20 X 5/8 HHCS

26 20 SSHC01064 1/4-20 X 1 HHCS

27 12 SSHC25080 3/8-16 X 1-1/4 HEX CAP

28 4 SSHC98032 10-32X1/2 HEX HD

29 4 SSHC98048 SCREW, HEX CAP #10-32X.75

30 8 SSHCM4X25 SCREW, HEX CAP

31 4 SSHCM5X16 SCREW, HEX CAP

32 16 SSSCM4X20 SCREW,SOC CAP,M4-0.7X20

33 8 WWF10 WASHER, FLAT, #10, COM

34 32 WWFS1/4 WASHER,FLAT,SAE,1/4

35 4 WWFS10 WASHER, FLAT, #10, SAE


37 8 WWFS6 WASHER, FLAT, #6


39 12 WWL10 WASHER,LOCK,#10

40 12 WWL3/8 WASHER, LOCK, 3/8


Page 98

Page

1379492 Laser Sub Assembly, 150 Watt AAC Drawing Number 1379492 Rev 3


1 1 1379222 SUPPORT, COLLIMATOR BRKT 26 1 FFRSP300048 POWER SUPPLY,SWITCHER

2 2 1379223 SUPPORT, COLLIMATOR-BEAM 27 2 MM5372K123 BARB,TUBE ADAPTER

3 1 1379425 BRACKET, POWER SUPPLY MNT 28 4 MM5413K51 CLAMP,HOSE,SOFT TUBING

4 * 1 1379426 CABLE ASY, LASER POWR 150W 29 1 MM6157K170 COLLAR,CLAMP,.875,1.63OD

5 1 1379458 BASE MTG PLATE, LASER 30 * 48" MM9336T3 TUBING,1/2"ID,3/4"OD

6 1 1379459 TRANSITION TUBE, 150 WATT 31 4 NNJ1/4-20 NUT, HEX, JAM, 1/4-20

7 1 1379463 ADAPTER, MODULAR, WIRING 32 2 NS6D17008 COUPLER, QC 1/2" BARBED

8 1 1379464 BLOCK, SUPPORT, LASER TOP 33 2 NS6D42008 PANEL MOUNT, QC 1/2" BARB

9 1 1379466 BLOCK, SUPPORT, LASER BTM 34 4 SSFCM4X8 SCREW,FLAT CAP,M4X8

10 2 1379493 BLOCK, SIDE ADJUSTEMENT 35 4 SSHC01048 1/4-20 X 3/4 HEX CAP

11 1 1379494 BLOCK, HEIGHT ADJUSTEMENT 36 4 SSHC01064 1/4-20 X 1 HHCS

12 2 1379776 MTG ANGLE- FIRST MIRROR 37 4 SSHC98048 SCREW, HEX CAP #10-32X.75

13 1 1379800 LASER INTERFACE,PCB ASSY 38 4 SSHCM5X16 SCREW, HEX CAP

14 1 1379872 COLLIMATOR, ASSY, 100W 39 11 SSSC01048 1/4-20 X 3/4" SOC CAP SC

15 * 1 1379-WD8 WIRING DIAGRAM 150W LASER 40 3 SSSC01048S 1/4-20 X 3/4 SOC CAP SC

16 1 AAQME-5-10 ELBOW, MALE,5/32X10-32 41 2 SSSC01096F 1/4-20 X 1-1/2 SOC CAP

17 1 AAQUT-5-5 QUICK UNION T,5/32X5/32 42 4 SSSC98056 10-32 X 7/8 SOC CAP

18 1 AATP5/32 TUBING, 5/32 OD 43 2 SSSS01096B SCREW,SKT SET,BRASS TIP

19 1 EECAT5EPS3 CABLE, CAT5E, SHIELDED 44 4 SSSS98048H 10-32 X 1 SOC SET SC

20 2 EECPAM100 BASE,MOUNTING,ADHESIVE 45 8 WWF10 WASHER, FLAT, #10, COM

21 1 EEE150L LASER,150W DIAMOND E150 46 5 WWFM6 WASHER, FLAT, M6, SAE

22 1 FF3234 STRAIN RELIEF,LIQ TIGHT 47 10 WWFS1/4 WASHER,FLAT,SAE,1/4

23 2 FF8463 NUT,LOCK,1/2NPT,NYLON,BLK 48 10 WWL1/4 WASHER,LOCK,1/4

24 1 FF8465 NUT,LOCK,3/4NPT,NYLON,BLK 49 4 WWL10 WASHER,LOCK,#10

25 2 FFM4518 STRAIN RELIEF,LIQ TIGHT 50 4 WWLM5 M5 LOCK WASHER

Page 119

Page

Page 98 Page


1379498 Laser Cooling System Assembly, 150 Watt AAC Drawing Number 1379498 Rev 0


1 * 1 1379-WD8 DIAGRAM,WIRING,150W LASER INTERFACE

2 * 1 400901 ALGAECIDE,LASER CHILLER, 1/2LB

3 1 1379476 FILTER STAND ASSEMBLY

4 1 1379495 CABLE ASSY,CHILLER REMOTE

5 * 1 MM3190K908 WATER,DISTILLED,100%, 5 GAL.

6 * 1 MM8673T21 COLANT,INHIBITED PROPLYENE GLYCOL

7 1 MMRC045J03 CHILLER,RECIRCULATING

8 2 NS6D24008 INSERT, QC 1/2" MALE NPT

Page 91 Page

Page 119 Page

1379476 Filter Stand Assembly, 150 Watt AAC Drawing Number 1379476 Rev 0


1 1 1379474 FLOWMETER STAND WELDMENT

2 1 1379477 COVER, FILTER STD,FM SIDE

3 7 1379478 PLATE, U-BOLT, 1-3/8 C-C

4 1 1379480 COVER, FILTER STD,CHLR SD

5 1 1379481 COVER, FILTER STD,LASR SD

6 1 1379482 COVER, FILTER STD,TOP

7 2 1379483 FLOW METER ASSEMBLY

8 1 1379484 FILTER HOUSING ASSEMBLY

9 1 1379485 RETURN LINE HOSE ASM

10 1 1379486 SUPPLY LINE HOSE ASM

11 1 1379487 RETURN LINE ASM, RH LASER

12 1 1379488 SUPPLY LINE ASM, RH LASER

13 1 1379489 RETURN LINE ASM, LH LASER

14 1 1379490 SUPPLY LINE ASM, LH LASER

15 2 1379496 FLOW METER CABLE ASM

16 7 MM5413K51 CLAMP,HOSE,SOFT TUBING

17 1 MM6637T37 FILTER,POLYPROPYLENE

18 7 MM8875T32 U-BOLT,1/4-20 THRD,3-3/16

19 14 NNC1_4-20 NUT, CAP, 1/4-20

20 14 NNE1/4-20 NUT,ELASTIC LOCK,1/4-20

21 4 NNK8-32 NUT,KEP,8-32

22 4 SSBC90048 8-32 X 3/4 BUTTON CAP

23 27 SSZH#10048 SCREW,SHT.METAL HEX 10

24 16 WWF1/4 WASHER, FLAT, 1/4", COM


1379148 Ro Clamp, 1.5ID, 3”OD AAC Drawing Number 1379148 Rev 1


1 1 1379150 BLOCK,SUPPORT

2 1 1379151 BAR, CAP, 1.5 OD

3 1 1379291 CONE,FLUTTED,2"~3.5" CORE

4 1 MM331 CLAMP, PULL LATCH

5 1 NNHM8X1.25 M8 X 1.25 HEX NUT

6 1 SSASM10XM60 SCREW,ALLEN SHOULDER

7 8 SSSCM6X15 M6X15 SOC CAP SCREW

8 1 WWFM8 8MM FLAT WASHER

9 6 WWLM6 M6 LOCK WASHER

1379210 Fluted Roll Clamp, 2” core AAC Drawing Number 1379210 Rev 0


1 1 1379201 BLOCK,SUPPORT

2 1 1379202 BAR, CAP, 2" OD

3 1 1379205 CONE,FLUTTED,2" CORE

4 1 MM331 CLAMP, PULL LATCH


6 1 SSASM10XM60 SCREW,ALLEN SHOULDER





1379835 Stacker Rack AAC Drawing Number 1379835 Rev 3


1 2 1379268 ARM, STACKER EXTENSION

2 1 1379270 ROD, STACKER EXTENSION

3 1 1379790 REST, MATERIAL STACK

4 4 MM132-1496 PLUG 1 X 2

5 1 MM1910A25M RULER,SILVER MYLAR 108"

6 *15" MM310 TAPE,SAFETY WALK,3M 310

7 2 SSSC01048 1/4-20 X 3/4" SOC CAP SC

8 2 SSSC01064 1/4-20 X 1 SOC CAP

9 2 SSW#1/4 WING SCREW KNOB

1379900 Vent Hood Assembly AAC Drawing Number 1379900 Rev 2


1 1 1379065 BRACE,DUCT FITTING


3 1 1379100 COVER, EYE ACCESS

4 2 1379898 HOOD PANEL, TOP


6 1 MMATT06 TAKE OFF,6"

7 4 NNE8-32 NUT,ELASTIC LOCK, 8-32

8 4 SSPP90048 #8-32 X 3/4 PAN HD PHIL

9 24 WWF8 WASHER, FLAT #8

10 18 SSPP90024 8-32X3/8 PAN PHLPS


1379950 Infeed Assembly AAC Drawing Number 1379950 Rev 3


1 * 1 1379-CAB3 INFEED CABLE PACKAGE

2 1 1379129 FLAG, EDGE GUIDING

3 1 1379130 MATERIAL GUIDE ROLLER ASM

4 2 1379135 STEP, CATWALK

5 1 1379175 CATWALK WELDMENT

6 1 1379180 ACCUMULATOR ASSEMBLY

7 1 1379190 EDGE GUIDE EYE ASSY

8 1 1379371 KIT, SAFETY GUARD

9 1 1379936 BAG CLOSING ASSY.

10 1 1379974 BAG CLOSING CLAMP ASM

Page

Page 106

Page

Page 99

Page

Page 103 Page

Page 105

Page

Page 101

Page

1379871 Collimator Assembly, 55W AAC Drawing Number 1379871 Rev 2


1 1 1379021 BEAM TUBE 68MM-COLLIMATOR



4 1 ADPC55ACMNT PLATE, ADAPTER FOR EEC55A


6 1 BEC194X10611 COLLIMATOR ASM, 55W

7 1 BTA19CMCM0068 BEAM TUBE 68MM-COLLIMATOR


1379872 Collimator Assembly, 100 & 150 Watt units AAC Drawing Number 1379872 Rev 2

NO. QTY PART# DESCRIPTION 1 1 1379021 BEAM TUBE 68MM-COLLIMATOR




5 1 BEC192X10610 COLLIMATOR ASM, 100W

6 1 BTA19CMCM0068 BEAM TUBE 68MM-COLLIMATOR

7 1 BTQ19CLCM BEAM COUPLER, 19MM

1379130 Material Guide Roller Assembly AAC Drawing Number 1379130 Rev 1


1 2 1379124 ROLLER, SUPPORT ASSY

2 3 1379125 SHAFT, FABRIC ROLLER

3 1 1379145 MATERIAL GUIDING FRAME

4 1 1379237 ROLLER, UNFINISHED ASSY

5 10 BBGER205-25 BEARING,BALL,25MMB,CLAMP

6 2 BBNAP205-25 BEARING, PILLOWBLOCK

7 4 MM132-2X4 END CAP,RECT,BLACK

8 * .50 RLMM310 TAPE,SAFETY WALK,3M 310

1379180 Accumulator Assembly AAC Drawing Number 1379180 Rev 4


1 1 1975-412A PLATE,NUT,4-40,.95CTC 42 2 BBAW-5Z ROD END

2 2 1379074 BLOCK,BEARING 43 1 BBAW-8Z BEARING,ROD END

3 1 1379082 PINCH ROLLER JOG ASM 44 1 BBGER205-25 BEARING,BALL,25M

4 1 1379103 WIRE WAY, LASER 45 8 BBNAP205-25 BEARING, PILLOW

5 1 1379110 COVER, WIRE WAY 46 3 EED78W308 DUCT,WIRE

6 2 1379137 SLEEVE, BEARING 47 3 EED78W332 DUCT,WIRE COVER

7 1 1379142 END COVER, FRAME, RH 48 1 EENI5Q18AN6X SENSOR, PROX

8 1 1379160 ACCUMULATOR FRAME 49 2 FFGLLA01A1B SWITCH, LIMIT

9 1 1379182 BRKT,MTG,EYE,UNIVER 50 2 FFM4518 STRAIN RELIEF,LIQ

10 1 1379922 ROLLER, DRIVE ASSY 51 1 FFSM312LVQ EYE,ELECTRIC,10-30

11 1 1379927 ROLLER, DRIVE ASSY 52 2 MM50 CHAIN, SINGLE

12 1 1379929 ARM WELDT-LH PINCH 53 2 MM50B17M STEEL SPROCKET

13 1 1379931 ARM WELDT-RH PINCH 54 2 MM50L LINK,MASTER,5/8P

14 1 1379933 BRKT, MOTOR 55 4 MM132-2X2 END CAP, 2x2 10-14

15 2 1379970 SUPPORT, FRAME 56 1 MM310 TAPE,SAFETY WALK

16 2 1379987 BRKT, END 57 2 MM4554K12 PLUG, 1/4" PIPE

17 2* 1391160 CABLE ASSY,VALVE,DIN 58 4 MM6301K82 SWIVEL LEVELING

18 2 1392900 WASHER, CHAIN 59 2 MM19425A46 RULER,HALF-SCALE

19 1 1393369 KEY, GEARMOTOR 60 2 MM93095K32M GUIDE, CHAIN

20 1 1393373 PLATE, NUT, 4-40 61 1 MMRV0501-30 MOTOR,GEARBOX,0

21 3 1493221 ROLLER ASSY 62 2 MMSH-98 RING,SNAP,EXTERN

22 2 1493222 WHEEL, RETAINER FOR 63 6 MMT9945 TAPE,REFLECTIVE,2"

23 1 1493224 TENSION ROLL 64 1 NNJ1/2-20 1/2-20 JAM NUT

24 2 1493226 EDGE GUIDE ASSY 65 2 NNJ5/16-24 NUT,JAM,5/16-24

25 1 1493232 MOUNT, ACCUMULATOR 66 2 NNJM5X0.8 NUT,JAM,HEX,M5

26 2 1493233 BRACKET, LIMIT, LOWER 67 4 SSFCM8X16 M8 X 16 FLAT CAP

27 2 1493234 BRACKET, LIMIT, UPPER 68 4 SSHC46080F 1/2-20X1-1/4 HEX

28 2 1493507 BRKT,BELT TENSION 69 2 SSSC10064 5/16-18X1 SOCKET

29 2 1493508 BLOCK,TENSION 70 3 SSSCM5X20 M5-0.8X20,SCREW

30 4 AA198RA408 FLOW CONTROL,1/4 71 1 SSSCM5X25 M5-0.8X25,SCREW

31 2 AA198RR404U FLOW CONTROL,1/4 72 4 SSSCM6X20 SCREW, SOCKET CAP

32 2 AAC6DP-3 CYLINDER,AIR,DA,MAG 73 4 SSSCM8X25 SCREW,SOC CAP

33 1 AAC316DXP CYLINDER,AIR,2" BORE 74 12 SSSCM8X30 SCREW,SOC CAP

34 2 AAE4V21008 VALVE, 1/4" PORTED 75 2 UUCFL207-20 1.25" BEARING

35 2 AAFBP-11C BRKT,PIVOT,1/4 BORE 76 3 WWFM5 WASHER, FLAT, M5

36 1 AAFD-229 BRKT, PIVOT, 3/8 BORE 77 4 WWFM8 WASHER, FLAT, M8

37 2 AAQMC-4-8 QUICK MALE CONN 78 12 WWFS5/16 WASHER,FLAT,SAE

38 4 AAQME-4-4 ELBOW, MALE 79 4 WWL1/2 1/2 LOCK WASHER

39 1 AAQME-4-8 ELBOW,QUICK MALE 80 2 WWL5/16 WASHER, LOCK

40 1 AAV41V VALVE,TOGGLE 81 1 WWL10 WASHER,LOCK,#10

41 2 BB305705C BEARING,CAM ROLLER 82 16 WWLM8 M8 LOCK WASHER


1379918 Bag Closer Assembly AAC Drawing Number 1379918 Rev 1


1 1 1379109 BLOCK,BAG CLOSER PIVOT

2 1 1379914 PLATE, BASE, BAG CLOSER

3 1 1379917 BRACKET,SEW HEAD

4 1 1379989 SUPPORT, ROD BAG CLOSER

5 1 BC-1 BORDER CLOSER MACHINE

6 1 FF770018-1 CONN,UML2,PLUG,3POS

7 * 3 FF770251-3 CONN,UML2,PIN,F,14-20AWG

8 1 MM8487A31 PIN,QUICK RELEASE

9 2 MMSLD-ECH 1/2" DIA RUBBER BUMPER

10 2 SSSCM6X16 M6-1.0 X 16 SOC CAP


12 2 WWL1/4 1/4 LW

1379190 Edge Guide Eye Assembly AAC Drawing Number 1379190 Rev 2


1 1 1379189 BLK, MTG, EDGE GUIDE EYE 10 2 SSBC90016 8-32 X 1/4 BUTTON CAP

2 1 1379192 BLOCK, CLAMP 11 4 SSSC70040 4-40 X 5/8, SCREW,SOCKET CAP

3 1 1379195 EDGE GUIDE POINTER 12 3 SSSC98048 10-32 X 3/4 SOC CAP

4 1 1379198 ROD, MTG, EDGE GUIDE EYE 13 4 SSSCM3X10 M3-0.5X10, SOCKET CAP

5 1 1379759 DUAL SENSOR MOUNT 14 2 SSSCM3X16 M3-0.5X16 ,SOCKET CAP

6 2 FF89F2608 SPACER,ALUMINUM,3/8 15 9 SSSCM3X8 M3-0.5X8 ,SOCKET CAP

7 2 FFSM312LVQ EYE,ELECTRIC,10-30VDC 16 1 TTH32416 HANDLE,THRD,1/4-20X1-1/8

8 1 MMGN12HZ0HN MGN12H BEARING BLOCK 17 1 WWFS1/4 WASHER,FLAT,SAE,1/4

9 1 MMGNR12R0800HN RAIL,LINEAR,MG12 SERIES 18 4 WWSI4 WASHER,INT. TOOTH


1379371 Safety Guard Kit AAC Drawing Number 1379371 Rev 0


1 1 1379363 END COVER, FRAME, RH

2 1 1379364 END COVER, FRAME, LH

3 2 1379365 SUPPORT, FRAME

4 2 1379366 FRONT COVER, FRAME

5 4 1379367 BRACKET, GUARD

6 2 1379368 END COVER, FINGER GUARD

7 1 1379378 HINGE BAR, TOP ROLLER GRD

8 1 1379380 BAR, GUARD SUPPORT, TOP

9 2 1379381 FRONT COVER, FRAME

10 78 sscm5x10 SCREW,CHEESE HEAD

11 2 SSHC10128 SCREW, HEX CAP

12 4 sshcm6x16S SCREW, HEX M6X16 SS

13 4 sshcm6x20S SCREW, HEX M6X20L SST



16 78 wwlm5 M5 LOCK WASHER

17 8 wwlm6 M6 LOCK WASHER

1379936 Bag Closing Assembly AAC Drawing Number 1379936 Rev 1


1 1 1379918 BAG CLOSER ASSY

2 1 1379938 TRAY,MICRO TRAC.

3 2 1392600 LIMITER

4 1 MM55835K121 BRKT SET,CABLE TRACK

5 1 MM55835K933 DUCT,WIRE PLASTITRAK

6 1 MMHGR30R2960HN RAIL,LINEAR, HG 2960MM

7 1 MMHGW30HCZ0HN LINEAR BEARING


9 4 SSBCM5X12 SCREW,BUTTON CAP

10 7 SSSCM5X10 M5-0.8 X 10 SOC CAP

11 17 SSSCM8X25 M8-1.25 X 25 SOC CAP

12 13 WWFM5 WASHER, FLAT, M5 I.D.





Page 102

Page


1379974 Bag Closing Clamp Assembly AAC Drawing Number 1379974 Rev 2


1 2 1379939 BLOCK,CLAMP PIVOT

2 2 1379940 BLOCK,HINGE

3 1 1379942 CLAMP, ANGLE

4 2 1379943 ROD,FLATTED,JEW,1/2ODX5.5

5 2 CCCL8F CLAMP COLLAR- 1/2

6 2 IID016X064 DOWEL PIN,1/4 X 1

7 9.5FT MM918L343 FOAM,SOFT,1/4 THK X 1 W

8 2 MMTC225U CLAMP,TOGGLE,HORIZ HANDLE

9 4 NNH5/16-18 5/16-18 HEX NUT

10 2 SSHC10128 5/16 - 18 X 2" SOCKET CAP

11 8 SSSCM6X20 SCREW, SOCKET CAP



1379990 Material Carriage Assembly AAC Drawing Number 1379990 Rev 1


1 2 1379025 TENSION RACK ASSY

2 2 1379043 BRKT,GUIDE

3 1 1379996 INFEED FRAME ASSEMBLY

4 4 MM132-2X2 END CAP, 2x2 10-14GA

5 4 MM431-4 CASTER,4",W/LOCKS

6 2 MMTC225U CLAMP,TOGGLE,HORIZ HANDLE

7 8 SSFC10056 5/16-18X7/8 FLAT HD CAP

8 16 SSHC10048 5/16-18 X 3/4 HHCS

9 12 SSHC10064 5/16-18 X 1 HHCS

10 8 SSHC98048 SCREW, HEX CAP #10-32X.75




14 28 WWL5/16 WASHER, LOCK, 5/16

1379D-PD Pneumatic Diagram 125785B


1379D-PD1 Pneumatic Diagram 125786B

1379D-PD2 Chiller Plumbing Diagram, 150 Watt 125878B


1379-WD1 Cabinet Wiring Diagram 125791B

1379-WD2 Bus Coupler I/O Wiring Diagram 125792B


1379-WD3 Laser Interface Wiring Diagram 125793B

1379-WD4 Laser Interface Wiring Diagram 125794B


1379-WD5 Interlock Safety Circuit Wiring Diagram 125752B

1379-WD6 Pendant Wiring Diagram 125744B


1379-WD7 Wiring Diagram, Safety Circuit 125777B

1379-WD8 Laser Interface Wiring Diagram, 150 Watt 125876B


Atlanta Attachment Company (AAC) Statement of Warranty

Manufactured Products Atlanta Attachment Company warrants manufactured products to be free from defects in material and workmanship for a period of eight hundred (800) hours of operation or one hundred (100) days whichever comes first. Atlanta Attachment Company warrants all electrical components of the Serial Bus System to be free from defects in material or workmanship for a period of thirty six (36) months.

Terms and Conditions: AAC Limited Warranty becomes effective on the date of shipment. AAC Warranty claims may be made by telephone, letter, fax or e-mail. All verbal claims must be con-

firmed in writing. AAC reserves the right to require the return of all claimed defective parts with a completed warranty

claim form. AAC will, at its option, repair or replace the defective machine and parts upon return to AAC. AAC reserves the right to make the final decision on all warranty coverage questions. AAC warranty periods as stated are for eight hundred (800) hours or one hundred (100) days whichever

comes first. AAC guarantees satisfactory operation of the machines on the basis of generally accepted industry

standards, contingent upon proper application, installation and maintenance. AAC Limited Warranty may not be changed or modified and is not subject to any other warranty

expressed or implied by any other agent, dealer, or distributor unless approved in writing by AAC in advance of any claim being filed.

What Is Covered Electrical components that are not included within the Serial Bus System that fail due to defects in

material or workmanship, which are manufactured by AAC are covered for a period of eight hundred (800) hours.

Mechanical parts or components that fail due to defects in material or workmanship, which are manufactured by AAC.

Purchased items (sewing heads, motors, etc.) will be covered by the manufacturers (OEM) warranty. AAC will assist in the procurement and handling of the manufacturers (OEM) claim.

What Is Not Covered Parts that fail due to improper usage, lack of proper maintenance, lubrication and/or modification. Damages caused by; improper freight handling, accidents, fire and issues resulting from unauthorized

service and/or personnel, improper electrical, plumbing connections. Normal wear of machine and parts such as Conveyor belts, "O" rings, gauge parts, cutters, needles, etc. Machine adjustments related to sewing applications and/or general machine operation. Charges for field service. Loss of time, potential revenue, and/or profits. Personal injury and/or property damage resulting from the operation of this equipment.

Declaración de Garantía

Productos Manufacturados Atlanta Attachment Company garantiza que los productos de fabricación son libres de defectos de material y de mano de obra durante un período de ochocientos (800) horas de operación o cien (100) días, cual llegue primero. Atlanta Attachment Company garantiza que todos los componentes del Serial Bus son libres de defectos de material y de mano de obra durante un periodo de treinta y seis (36) meses.

Términos y Condiciones: La Garantía Limitada de AAC entra en efecto el día de transporte. Reclamos de la Garantía de AAC pueden ser realizados por teléfono, carta, fax o correo electrónico. Todo

reclamo verbal tiene que ser confirmado vía escrito. AAC se reserva el derecho de exigir el retorno de cada pieza defectuosa con un formulario de reclamo de

garantía. AAC va, según su criterio, a reparar o reemplazar las máquinas o piezas defectuosas devueltas a AAC. AAC se reserva el derecho para tomar la decisión final sobre toda cuestión de garantía. Las garantías de AAC tiene una validez de ochocientas (800) horas o cien (100) días, cual llega primero. AAC garantiza la operación satisfactoria de sus máquinas en base de las normas aceptadas de la industria

siempre y cuando se instale use y mantenga de forma apropiada. La garantía de AAC no puede ser cambiada o modificada y no está sujeto a cualquier otra garantía

implicada por otro agente o distribuida al menos que sea autorizado por AAC antes de cualquier reclamo.

Lo Que Está Garantizado Componentes eléctricos que no están incluidos dentro del sistema Serial Bus que fallen por defectos de

materiales o de fabricación que hayan sido manufacturados por AAC, son garantizados por un período de ochocientas (800) horas.

Componentes mecánicos que fallen por defectos de materiales o de fabricación que hayan sido manu-facturados por AAC, son garantizados por un período de ochocientas (800) horas.

Componentes comprados (Motores, Cabezales) son protegidos debajo de la garantía del fabricante. AAC asistirá con el manejo de todo reclamo de garantía bajo la garantía del fabricante.

Lo Que No Está Garantizado Falla de repuestos a raíz de uso incorrecto, falta de mantenimiento, lubricación o modificación. Daños ocurridos a raíz de mal transporte, accidentes, incendios o cualquier daño como resultado de

servicio por personas no autorizados o instalaciones incorrectas de conexiones eléctricas o neumáticas. Desgaste normal de piezas como correas, anillos de goma, cuchillas, agujas, etc. Ajustes de la máquina en relación a las aplicaciones de costura y/o la operación en general de la máquina. Gastos de Reparaciones fuera de las instalaciones de AAC Pérdida de tiempo, ingresos potenciales, y/o ganancias. Daños personales y/o daños a la propiedad como resultado de la operación de este equipo.


Atlanta Attachment Company 362 Industrial Park Drive Lawrenceville, GA 30046 770-963-7369 www.atlatt.com Printed in the USA

technical manual & parts lists€¦ · 15/3/2016 · 362 industrial park drive . atlanta...

Documents