technical support document for draft air …technical support document, permit action number:...

Technical Support Document, Permit Action Number: 15700015 ‐ 012 Page 1 of 9

TECHNICAL SUPPORT DOCUMENT

For DRAFT AIR EMISSION PERMIT NO. 15700015‐012

This technical support document (TSD) is intended for all parties interested in the draft permit and to meet the requirements that have been set forth by the federal and state regulations (40 CFR § 70.7(a)(5) and Minn. R. 7007.0850, subp. 1). The purpose of this document is to provide the legal and factual justification for each applicable requirement or policy decision considered in the preliminary determination to issue the draft permit. 1. General Information 1.1 Applicant and Stationary Source Location:

Table 1. Applicant and Source Address

Applicant/Address Stationary Source/Address (SIC Code: 3321, 3365) Federal‐Mogul Corporation 520 North 8th Street Lake City, MN 55041

Federal‐Mogul Corp Powertrain Systems 520 North 8th Street Lake City, Wabasha County, Minnesota 55041

Contact: Ron Koller 651‐345‐8005 1.2 Facility Description Federal‐Mogul Corporation Powertrain Systems (Federal‐Mogul) owns and operates a foundry in Lake City, Minnesota. The facility consists of separate gray iron and aluminum foundry operations, supporting machine operations, and natural gas‐fired boilers. The raw materials consist entirely of refined and scrap metals, and scrap generated from in‐house machining operations and various materials for mold making. The gray iron foundry is dedicated to making sleeves, rather than pistons.

Federal‐Mogul operates the gray iron foundry with six induction furnaces with a combined rated capacity of 21.41 tons of metal melted per hour. Other equipment at the facility includes a seven‐ton holding furnace for storing molten gray iron, a high pressure pouring and cooling line rated at 125 molds per hour, sand muller, sand silos and three centrifugal casting lines. In addition, for the aluminum foundry, the facility operates the central melting furnace, holding furnaces, and casting and heat treating ovens.

The main sources of air emissions are Particulate Matter (PM), PM less than 10 microns (PM10) and Nitrogen Oxides (NOX). The facility operates under an individual State permit and is an area source under National Emission Standards for Hazardous Air Pollutants (40 CFR pt. 63).

1.3 Description of the Activities Allowed by this Permit Action This permit action is for two Major Amendments and an Administrative Amendment. One major amendment (DQ 4517) will add an emergency generator (EU192) to the facility with its own associated stack (SV053). The engine will run on diesel fuel, not have control equipment and be used for emergency use only.


The second major amendment (DQ 4622) will re‐route emissions from machining lathes (EU052‐055, 079‐081) to the baghouse CE016 (SV039). These lathes were previously controlled by baghouse CE015 (SV030). No permit limits will be revised by this change and thus, no previously modeled parameters will be affected. In addition, EU050 and EU051 (Casting Cutting Stations 1‐4 and 1‐5) and EU077 and EU078 (Casting Cutting Station 2‐4 and 2‐5) will be removed.

The administrative amendment is for a 120‐day extension on the SV041 performance test for PM2.5. The extension moved the due date to on or before November 13, 2010. The test was conducted November 9‐11, 2010. The most recent test for PM, PM10, PM2.5 and opacity at SV041 was conducted February 24, 2011.

Additional changes to the permit include removing requirements for tasks that have been completed, and updating Title I conditions to reflect the fact the facility operates under a State individual permit. Since the facility is no longer a Pt. 70 permit, all citations referencing CAM no longer are applicable. As CAM no longer applies, GP010 will be removed from the permit and associated items from GP010 will be moved to GP002 (fabric filters, non‐CAM). Collection and capture efficiencies at GP002 will be combined into overall control efficiency limits. The requirements at GP004 were combined into GP002 and GP004 was removed. The previous permit contained a schedule of compliance (Table C) to certify hoods at the facility. This schedule ran from 2009 to 2011, so these requirements can also be removed. The general provisions from 40 CFR pt. 63, subp. A that are applicable to 40 CFR pt. 63, subp. ZZZZZ have been added to GP013. The general provisions applicable to 40 CFR pt. 63, subp. ZZZZZZ have been added to GP014.

1.4 Facility Emissions:

Table 2. Emissions Summary (minor NSR source scenario)

Pollutant

Unlimited Potential Emissions from the

Modification (tpy)

Limited Potential Emissions from the Modification

(tpy)

Total Facility Limited Potential Emissions**

(tpy)

Pt. 70 Threshold for Criteria Pollutants

(tpy) PM 0.67 0.67 88.19 100PM10 0.67 0.67 57.75 100PM2.5 0.67 0.67 24.53 100NOX 14.33 14.33 94.88 100SO2 4.70 4.70 5.26 100CO 3.07 3.07 14.76 100Ozone (VOC) 14.33 14.33 47.48 100Lead ‐‐ ‐‐ 0.63 10CO2e* 2691.49 2691.49 66,849 100,000HAP Total ‐‐ ‐‐ 0.26 25*Carbon dioxide equivalents as defined in Minn. R. 7007.0100. ** Including Insignificant Activities

Table 3. Facility Classification Classification Major/Affected Source Synthetic Minor/Area Minor/Area

PSD X (PM/PM10/PM2.5) Part 70 Permit Program X (PM10/PM2.5) Part 63 NESHAP X


2. Regulatory and/or Statutory Basis New Source Review Federal‐Mogul is one of 28 source categories listed in the Prevention of Significant Deterioration (PSD) rules that are classified as major sources, if the potential‐to‐emit (PTE) is equal to or greater than 100 tons per year (tpy) of any single regulated pollutant. Title I Condition limits were established in 2000 before the facility became a major source. PTE was revised during permit action ‐011 resulting in all regulated pollutants being below 100 tpy; therefore the facility is a non‐major source under New Source Review (40 CFR § 52.21). This permit action does not change the facility status under NSR. Part 70 Permit Program The limited PTE of all Pt. 70 regulated pollutants are below the 100 tpy threshold; therefore the facility is a non‐major source under the Pt. 70 program. Existing limits in the permit to avoid major source and modification under 40 CFR § 52.21 were updated to also avoid classification as major source under 40 CFR § 70.2. New Source Performance Standards (NSPS) The proposed emergency engine (EU192) is subject to New Source Performance Standard subp. IIII: Stationary Compression Ignition (CI) Internal Combustion Engines (ICE). National Emission Standards for Hazardous Air Pollutants (NESHAP) The proposed emergency engine (EU192) is subject to NESHAP subp. ZZZZ: Stationary Reciprocating Internal Combustion Engines (RICE). Compliance Assurance Monitoring (CAM) This is an individual State permit so CAM does not apply to the facility. All CAM citations effective from permit no. 15700015‐010 that were no longer applicable as of the issuance date of permit no. 15700015‐011 were removed from the permit in this permit action (‐012). Environmental Review & Air Emissions Risk Analysis (AERA) An Environmental Assessment Worksheet (EAW) is not required for this permit action, and the Permittee is not required to perform an AERA. Minnesota State Rules Portions of the facility are subject to the following Minnesota Standards of Performance:

Minn. R. 7011.2300 Standards of Performance for Stationary Internal Combustion Engines (ICE)

Table 4. Regulatory Overview of Units Affected by the Modification/Permit Amendment Subject Item* Applicable Regulations Rationale

EU192 40 CFR pt. 60, subp. IIII 40 CFR pt. 63, subp. ZZZZ Minn. R. 7011.2300, subps. 1, 2

New Source Performance Standard for Stationary CI ICE. National Emission Standards for Hazardous Air Pollutants for Stationary RICE. State Standards for Stationary ICE.


Subject Item* Applicable Regulations Rationale

GP002 Title I Conditions to avoid NSR and Pt. 70 and demonstrate compliance with NAAQS

Requirements to vent emissions to air pollution control equipment to remain a minor source and modification under NSR and minor source under Pt. 70.

Standards of Performance for Industrial Process Equipment: applies to individual emission units.

*Location of the requirement in the permit (e.g., EU, SV, GP, etc.). 3. Technical Information Federal‐Mogul will install an emergency generator (EU192) with its own stack (SV053) and no associated control equipment. The engine will run on diesel fuel and be used for emergency purposes only. The engine will be subject to New Source Performance Standards (NSPS) for Stationary Compression Ignition (CI) Internal Combustion Engines (ICE), State Performance Standards for Stationary ICE and National Emission Standards for Hazardous Air Pollutants (NESHAP) for Stationary Reciprocating Internal Combustion Engines (RICE). The emergency engine will comply with the applicable NESHAP standard by demonstrating compliance with the applicable NSPS requirements. The engine’s rated capacity is 530 hp and is model year 2013 which qualifies it as a Tier 3 engine per Table 1 of 40 CFR Section 89.112(a).

The administrative amendment application included with this permit action was for a 120‐day extension on the performance test for PM2.5 on SV041 (CE018). The extension moved the test due date from July 16, to November 13, 2010. The most recent performance test for SV041 was conducted February 24, 2011. Other performance test dates, frequencies and future test dates for SV030, SV039, SV041 and SV045 are shown below in Table 5. Performance test dates in the permit have been updated to the frequencies and due dates shown below. Test frequency plan requirements for initial PM2.5 tests were removed. The performance tests below included verification of PM2.5 emission rates. With this permit action, PM2.5 limits will be added to the permit at the SV levels listed in Table 6 giving a 10 % buffer above the verified results from the PM2.5 tests.

Table 5. Future Performance Testing Stack Previous

Test Test Frequency Pollutants Tested Next Test

Due SV030 9/29/11 every 60 months PM, PM10, PM2.5, opacity 9/29/16 SV039 11/15/12 every 60 months PM, PM10, PM2.5, opacity 11/15/17 SV041 2/24/11 every 60 months PM, PM10, PM2.5, opacity 2/24/16 SV045 8/1/12 every 60 months PM, PM10, PM2.5, opacity 8/1/17

A notification of compliance for NESHAP subp. ZZZZZZ was received July 9, 2009. The applicable requirements for this NESHAP were placed in the permit during the last amendment (‐011). The compliance trigger date (June 27, 2011) requirement will be removed during this permit action.

Federal‐Mogul is also re‐routing seven machining lathes (EU052‐055, 079‐081) from CE015 (SV030) to CE016 (SV039). Permit limits at SV030 and SV039 will not be affected by this change and there are no changes to any previously modeled parameters in permit Appendix D.

Cleanup and Corrections to the Permit


Requirements and citations at the Total Facility level of the permit were updated to current MPCA practice. Federal‐Mogul’s permit type went from Federal Pt. 70/Major for NSR in permit action ‐010 to an individual State in permit action ‐011. Title I conditions in the permit to avoid major source status and modification under 40 CFR Section 52.21 and Minn. R. 7007.3000 are being updated to include limits to avoid major source status under 40 CFR Section 70.2 and Minn. R. 7007.0200 in the citations. None of the permit limits are being changed. Also Title I conditions to avoid only a major modification under 40 CFR Section 52.21 and Minn. R. 7007.3000 will now avoid major status under 40 CFR Sections 52.21 and 70.2. None of these permit limits are being changed either.

Federal‐Mogul first became a major source under 40 CFR Sections 52.21 and 70.2 and initially took limits to avoid a major modification under the federal Prevention of Significant Deterioration (PSD) program and thus, avoid the need to conduct a Best Available Control Technology (BACT) analysis with that permit action. (See discussion in permit 15700015‐002 TSD) The facility production limit established in PER002 of 121,680 tpy was reduced to 65,000 tpy in PER008 in order to show compliance with National Ambient Air Quality Standards for PM10.

Also, as part of becoming a State permit and no longer being a major source under 40 CFR Section 70.2 the Compliance Assurance Monitoring (CAM) requirements from 40 CFR pt. 64 are no longer applicable. All citations referencing CAM (i.e., 40 CFR pt. 64) were removed from the permit. Since CAM no longer applies to this facility, GP010 will be removed from the permit and associated items under GP010 will be moved to GP002 (non‐CAM fabric filters). The previous permit contained capture and collection efficiencies for fabric filters in GP002 and 010. This permit will combine the two efficiencies into an overall control efficiency for each fabric filter by multiplying the capture and collection efficiencies. (i.e., control efficiency = capture efficiency * collection efficiency) The resultant control efficiencies for GP002 are shown below in Table 6.

The permit contained a schedule of compliance in Table C to certify the hoods at the facility. This hood certification was to run for three years from 2009 to 2011. Since this has been completed, the associated permit requirements are being removed.

3.1 Calculations of Potential to Emit and Emissions Increase Analysis Potential‐to‐emit (PTE) calculations for the emergency generator are included in Attachment 2 to this TSD. PTE for greenhouse gases (GHG) were provided with the application for permit ‐011 and included again with the application for permit ‐012. As GHGs were not regulated pollutants at the time of permit ‐011 issuance the PTE data was not entered in the facility description at that time. All PTE for GHG (including CO2, CH4, N2O and CO2e) will be entered into the facility description with permit ‐012 and reflect the global warming potentials as revised in the November 29, 2013 Federal Register. 3.2 Dispersion Modeling Federal‐Mogul’s permit contains the following language triggering the need for modeling.

For changes that require a minor, moderate, or major permit amendment and affect any modeled parameter or emission rate documented in Appendix D, a Remodeling Submittal requirement is triggered.

Federal‐Mogul was in contact with MPCA staff via email correspondence and phone conversations and determined that modeling would not be required for the following reasons:

The proposed generator does not affect the original modeled parameters or emission rates.


Emergency generators, per MPCA modeling guidelines, do not normally require modeling. EU192 will operate under Best Management Practices (BMPs) for emergency generators.

3.3 Monitoring In accordance with the Clean Air Act, it is the responsibility of the owner or operator of a facility to have sufficient knowledge of the facility to certify that the facility is in compliance with all applicable requirements. In evaluating the monitoring included in the permit, the MPCA considered the following:

the likelihood of the facility violating the applicable requirements; whether add‐on controls are necessary to meet the emission limits; the variability of emissions over time; the type of monitoring, process, maintenance, or control equipment data already available for

the emission unit; the technical and economic feasibility of possible periodic monitoring methods; and the kind of monitoring found on similar units elsewhere.

The table below summarizes the monitoring requirements associated with this amendment.

Table 6. Monitoring Subject Item*

Requirement (rule basis) Monitoring Discussion

EU192 CO:


Subject Item*

Requirement (rule basis) Monitoring Discussion

SV039 (CE016)

PM10: ≤ 1.25 lb/hr on 24‐hr rolling avg PM2.5: 79.2% control efficiency PM2.5: > 77.6% control efficiency (to avoid 40 CFR §§ 52.21 and 70.2; Minn. R. 7007.3000 and 7007.0200)

Recordkeeping: daily visible emission check, reading, monitoring and maintain pressure drop

Monitoring based on MN Performance Standard for Control Equipment is adequate to have a reasonable assurance of compliance (daily, periodic inspections and corrective actions). All situations warranting corrective actions are deviations. The Permittee shall report the deviations in the semiannual deviations report.

*Location of the requirement in the permit (e.g., EU, SV, GP, etc.). 3.4 Insignificant Activities Federal‐Mogul Corp Powertrain Systems has several operations which are classified as insignificant activities under the MPCA’s permitting rules. These are listed in Appendix B to the permit. Space heaters that previously qualified as insignificant activities under Minn. R. 7007.1300, subp. 3.A will now qualify under Minn. R. 7007.1300, subp. 3.I.


The permit is required to include periodic monitoring for all emissions units, including insignificant activities, per EPA guidance. The insignificant activities at this Facility are only subject to general applicable requirements. Using the criteria outlined earlier in this TSD, the following table documents the justification why no additional periodic monitoring is necessary for the insignificant activities affected by this modification.

Table 7. Insignificant Activities

Insignificant Activity General Applicable

Emission limit Discussion Space heaters fueled by natural gas or propane, now qualifying under Minn. R. 7007.1300, subp. 3.I.

PM ≤ 0.4 lb/MMBtuOpacity ≤ 20% with exceptions (Minn. R. 7011.0515)

For these space heaters, based on the fuels used and EPA published emissions factors, it is highly unlikely that it could violate the applicable requirement. In addition, these types of units are typically operated and vented inside a building, so testing for PM or opacity is not feasible.

3.5 Permit Organization In general, the permit meets the MPCA Delta Guidance for ordering and grouping of requirements. One area where this permit deviates slightly from Delta guidance is in the use of appendices. While appendices are fully enforceable parts of the permit, in general, any requirement that the MPCA thinks should be electronically tracked (e.g., limits, submittals, etc.), should be in Table A or B of the permit. The main reason is that the appendices are word processing sections and are not part of the electronic tracking system. Violation of the appendices can be enforced, but the computer system will not automatically generate the necessary enforcement notices or documents. Staff must generate these.

Another area that deviates from the guidance is in the use of groups where the requirements in the group apply to the members of the group individually. This was done in order to shorten the permit and where no testing or tracking specific to a unit is in the permit (thereby reducing the likelihood that there where will be further unit‐specific requirements later). 3.6 Comments Received to be completed after public notice and EPA review Public Notice Period: ‐ EPA 30‐day Review Period: ‐ Comments were received from the public during the public notice period. Comments were received from EPA during their review period. Changes to the permit were made as a result of the comments. Provide summary of changes. > 4. Permit Fee Assessment


Attachment 3 to this TSD contains the MPCA’s assessment of Application and Additional Points used to determine the permit application fee for this permit action as required by Minn. R. 7002.0019. The permit action includes three permit applications, of which all were received after the effective date of the rule (July 1, 2009). Additional points include reviews of applicable NSPS subp. IIII (10 pts.) and NESHAP subp. ZZZZ (10 pts.). 5. Conclusion Based on the information provided by Federal‐Mogul Corp Powertrain Systems, the MPCA has reasonable assurance that the proposed operation of the emission facility, as described in the Air Emission Permit No. 15700015‐012 and this TSD, will not cause or contribute to a violation of applicable federal regulations and Minnesota Rules. Staff Members on Permit Team: Tarik Hanafy (permit engineer)

Ladislaus Strzok (enforcement) Jim Kolar (compliance) Sarah Seelen (peer reviewer) Beckie Olson (permit writing assistant) Sandra Simbeck (administrative support)

AQ File No. 2177; DQ 4517 (major), 4622 (major), 3164 (admin), 3206 (NESHAP subp. ZZZZZZ notification) Attachments: 1. Facility Description and CD‐01 Forms

2. Calculation Spreadsheets 3. Hood Certification Summary 4. Points Calculator

Attachment 1: Facility Description and CD01 Forms

MINNESOTA POLLUTION CONTROL AGENCYAIR QUALITY520 LAFAYETTE ROADST. PAUL, MN 55155-4194

Show:Action:AQD Facility ID:Facility Name:

Active and Pending RecordsPER 01215700015Federal-Mogul Corp Powertrain Systems

FACILITY DESCRIPTION: GROUPS (GP)

12 November, 2014 10:00

ID No. AddedBy

(Action)

RetiredBy

(Action)

Includein EI

OperatorID

for Item

Group Description Group ItemsGroupStatus

1 GP 001 PER 011 Charge Handling (2) and Induction Furnaces (6) EU 001, EU 004, EU 035, EU 041, EU 098, EU 099, EU 100, EU 131, EU 132,EU 165

Active

2 GP 002 PER 010 Fabric Filter-Low Temperature, i.e., T, 180 Degrees F - Applies to each CE CE 016, CE 017, SV 039, SV 040Active

3 GP 002 PER 012 Fabric Filter-Low Temperature, i.e., T, 180 Degrees F - Applies to each CE CE 002, CE 015, CE 016, CE 017, SV 004, SV 030, SV 039, SV 040Active

4 GP 003 PER 011 Industrial Process Equipment - Applies to each CE CE 005, CE 006, EU 012, EU 013, SV 007, SV 008Active

5 GP 004 PER 011 Fabric Filter- Low Temperature, i.e., T,< 180 Degrees F - Applies to each CE CE 002, CE 011, EU 009, EU 129, EU 130, SV 004Active

6 GP 004 PER 012 Fabric Filter- Low Temperature, i.e., T,< 180 Degrees F - Applies to each CERemoved

7 GP 005 PER 010 RemovedActive

8 GP 006 PER 010 Industrial Process Equipment - Applies to each EU EU 001, EU 043, EU 070, EU 098, EU 103, EU 131Active

9 GP 007 PER 011 Centrifugal Casting Lines #1 and #2 Operation Group EU 001, EU 042, EU 043, EU 044, EU 047, EU 048, EU 049, EU 050, EU 051,EU 052, EU 053, EU 054, EU 055, EU 056, EU 057, EU 059, EU 060, EU 061,EU 062, EU 063, EU 064, EU 065, EU 066, EU 067, EU 068, EU 069, EU 070,EU 071, EU 074, EU 075, EU 076, EU 077, EU 078, EU 079, EU 080, EU 081,EU 082, EU 083, EU 086, EU 087, EU 088, EU 096, EU 097, EU 099, EU 100,EU 145, EU 146, EU 147, EU 148, EU 149, EU 150, EU 151

Active

10 GP 007 PER 012 Centrifugal Casting Lines #1 and #2 Operation Group EU 001, EU 042, EU 043, EU 044, EU 047, EU 048, EU 049, EU 052, EU 053,EU 054, EU 055, EU 056, EU 057, EU 059, EU 060, EU 061, EU 062, EU 063,EU 064, EU 065, EU 066, EU 067, EU 068, EU 069, EU 070, EU 071, EU 074,EU 075, EU 076, EU 079, EU 080, EU 081, EU 082, EU 083, EU 086, EU 087,EU 088, EU 096, EU 097, EU 099, EU 100, EU 145, EU 146, EU 147, EU 148,EU 149, EU 150, EU 151

Active

11 GP 008 PER 011 Direct Heating Equipment - Applies to each Emission Unit EU 023, EU 024, EU 026, EU 038, EU 040, EU 059, EU 060, EU 061, EU 062,EU 063, EU 064, EU 065, EU 066, EU 067, EU 068, EU 086, EU 087, EU 088,EU 119, EU 120, EU 121

Active

12 GP 009 PER 011 Centrifugal Casting Line #3 Operation Group and Shot Blast Cleaning of HPLCasting #3 (EU 130)

CE 019, EU 098, EU 101, EU 102, EU 103, EU 104, EU 107, EU 108, EU 109,EU 110, EU 111, EU 112, EU 113, EU 114, EU 115, EU 116, EU 117, EU 118,EU 119, EU 120, EU 121, EU 131, EU 132, EU 133, EU 134, EU 135, EU 140,EU 154, SV 043, SV 044, SV 045

Active

13 GP 010 PER 010 Fabric Filters- Subject to CAM CE 002, CE 015, SV 004, SV 030Active

14 GP 010 PER 012 Fabric Filters- Subject to CAMRemoved

15 GP 011 PER 011 Boilers EU 033, EU 034, SV 028, SV 029Active

16 GP 012 PER 011 Evaporators EU 136, EU 137, EU 138, EU 139, SV 046, SV 047, SV 048, SV 049Active

17 GP 013 PER 011 40 CFR pt. 63, subp. ZZZZZ CE 015, CE 017, CE 019, CE 020, EU 004, EU 035, EU 041, EU 099, EU 100,EU 132, EU 165

Active

18 GP 014 PER 011 40 CFR pt. 63, subp. ZZZZZZ EU 024, SV 019Active

Page 1 of 1


Show: Active and Pending RecordsAction: PER 012AQD Facility ID: 15700015Facility Name: Federal-Mogul Corp Powertrain Systems

12 November, 2014 10:01

FACILITY DESCRIPTION: STACK/VENTS (SV)

ID No. Discharge DirectionFlow Rate/Temperature

Information Source

Exit GasTemperature

at Top(ºF)

DesignFlow Rate

at Top(ACFM)

Width(feet)

Diameteror Length

(feet)

Inside DimensionsHeight ofOpening

FromGround(feet)

AddedBy

(Action)

RetiredBy

(Action)

OperatorID

for Item

Operators DescriptionStack/Vent

Status

1 SV 001 Up, No CapEstimate90140002.540PER 011 CIF HighbayActive

2 SV 002 Up, No CapEstimate90200002.540PER 011Removed

3 SV 003 Up, No CapEstimate90140002.520PER 008Retired

4 SV 004 Up, No CapEstimate100400002.645PER 008 Fabric Filter CE 002Active

5 SV 005 Up, No CapEstimate9083552.5220PER 010 Fabric Filter CE 003Removed

6 SV 006 Up, No CapEstimate8020001120PER 011Removed

7 SV 007 Up, No CapEstimate901001.5120PER 008 Fabric Filter CE 005Active

8 SV 008 Up, No CapEstimate901001.550PER 011 Fabric Filer CE 006Active




12 SV 012 Up, No CapTest18002761.520PER 002Removed

13 SV 013 Up, No CapTest1038900140PER 011Removed

14 SV 014 Up, No CapEstimate7511711.520PER 011 Machine Area General VentActive



17 SV 017 Up, No CapTest743500120PER 011Removed

18 SV 018 Up, No CapEstimate1001565120PER 011 Piston Heat TreatingActive

19 SV 019 Up, No CapEstimate400902430PER 010 Aluminun Foundry Central Melting FurnaceActive

20 SV 020 Up, No CapEstimate1308230130PER 011 Aluminum Foundry Vanisil Dross HopperActive

21 SV 021 Up, No CapTest8013344330PER 011 Aluminum Foundry Holding FurnacesActive


23 SV 023 Up, No CapEstimate903323230PER 008 Fabric Filer CE 013Active

24 SV 024 Up, No CapEstimate3001452330PER 011 Aluminum Chip DryingRetired

25 SV 025 Up, No CapEstimate200500124PER 011 Peerless BoilerRetired

26 SV 026 Up, No CapTest7625001.530PER 010 PlatingRemoved

27 SV 027 Up, No CapEstimate200500124PER 011 Slant/Fin BoilerRetired

Page 1 of 2



12 November, 2014 10:01

FACILITY DESCRIPTION: STACK/VENTS (SV)

ID No. Discharge DirectionFlow Rate/Temperature

Information Source

Exit GasTemperature

at Top(ºF)

DesignFlow Rate

at Top(ACFM)

Width(feet)

Diameteror Length

(feet)

Inside DimensionsHeight ofOpening

FromGround(feet)

AddedBy

(Action)

RetiredBy

(Action)

OperatorID

for Item

Operators DescriptionStack/Vent

Status

28 SV 028 Up, With CapEstimate400500.820PER 011 Bryan BoilerActive

29 SV 029 Up, With CapEstimate300500.830PER 011 Weil-McLain BoilerActive

30 SV 030 Up, No CapEstimate9050000440PER 011 Fabric Filter CE 015Active

31 SV 031 Up, No CapTest2601360.8328PER 011 Aluminum Foundry Heat Treating Oven - sowActive

32 SV 032 Up, No CapTest3051750.8327PER 011 Sleeve Machine Shop Heat Treating OvenActive

33 SV 033 Up, No CapEstimate7015,000330PER 011 Die Coating Operations Line #1Active

34 SV 034 Up, No CapEstimate7015,000331PER 011 Die Coating Operations Line #2Active

35 SV 035 Up, No CapEstimate7015,000336PER 011 Nearest General Facility Vent for Die Preheating Burners Line #1Active

36 SV 036 Up, No CapEstimate20015,000331PER 011 Exhaust Stack for Die Preheating Burners Line #2Active

37 SV 037 PER 011 Centrifugal Pour & Cool Line #1Removed

38 SV 038 Up, No CapPER 011 Centrifugal Pour & Cool Line #2Removed

39 SV 039 Up, No CapEstimate8642,3205.560PER 011 Fabric Filter CE 016Active

40 SV 040 Up, No CapEstimate10018000340PER 011 Fabric Filter CE 017Active

41 SV 041 Up, No CapTest9954,350440PER 011 Fabric Filter CE 018Active

42 SV 042 Up, No CapEstimate7015,000331PER 010 Nearest General Facility Vent for Die Coating Operations Line #3Active

43 SV 043 Up, No CapEstimate10015,000231PER 011 Exhaust Stack for Die Preheating Burners Line #3Active

44 SV 044 Up, No CapEstimate7015,000331PER 010 Centrifugal Line #3-Charge HandlingActive

45 SV 045 Up, No CapEstimate9065,000560PER 011 Fabric Filter CE 019Active

46 SV 046 Up, No CapManufacturer450520.7531PER 011 Evaporator #1 StackActive




50 SV 050 Up, No CapEstimate7020,0002.3231PER 011 FM CGI Baghouse Stack (CE020)Active

51 SV 051 Up, No CapEstimate7015,000421PER 011 Nearest Facility Vent for W/C 791Active

52 SV 052 Up, No CapEstimate7015,000421PER 011 Nearest Facility Vent for W/C 791Active

53 SV 053 Up, No CapManufacturer107629880.29212PER 012 Emergency GeneratorActive

Page 2 of 2



12 November, 2014 10:01

FACILITY DESCRIPTION: CONTROL EQUIPMENT (CE)

ID No. AddedBy

(Action)

RetiredBy

(Action)

OperatorID

for Item

Control

Equip.Type

Control Equipment Description ModelControlEquip.Status

Manufacturer PollutantsControlled

AfterburnerCombustionParameters

CaptureEfficiency

(%)

Destruction/CollectionEfficiency

(%)

1 CE 001 PER 010 018 Fabric Filter - Low Temperature, i.e., T



12 November, 2014 10:01

FACILITY DESCRIPTION: CONTROL EQUIPMENT (CE)

ID No. AddedBy

(Action)

RetiredBy

(Action)

OperatorID

for Item

Control

Equip.Type

Control Equipment Description ModelControlEquip.Status

Manufacturer PollutantsControlled

AfterburnerCombustionParameters

CaptureEfficiency

(%)

Destruction/CollectionEfficiency

(%)

21 CE 021 PER 011 018 Fabric Filter - Low Temperature, i.e., T

ST. PAUL, MN 55155-4194

Show: Active and Pending RecordsAction: PER 012AQD Facility ID: 15700015Facility Name:

MINNESOTA POLLUTION CONTROL AGENCYAIR QUALITY520 LAFAYETTE ROAD

12 November, 2014 10:02

FACILITY DESCRIPTION: EMISSION UNIT (EU)

MaxFuelInput

(mil Btu)

Federal-Mogul Corp Powertrain Systems

RetiredBy

(Action)

Operator DescriptionID No. EmissionUnit

Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity

SICManufacturer ModelNumber

Max.Design

Capacity

MaximumDesign

Capacity

Materials Units n Units d

1 FM Charge Handling BridgeCrane

EU 001 Active PER 011 SV 001 (M) Hr 3321Northern Engineering 10 Ton 10.25 Ton

2 FM Charge Handling BridgeCrane - Material HandlingEquipment

EU 001 Active PER 012 SV 001 (M) Hr 3321Northern Engineering 10 Ton 10.25 Ton

4.83 Two Natural Gas FiredPreheater Buckets

EU 002 Removed PER 011 Hr 3321Lindberg CF-53-C 9 Ton

4 Two Existing CorelessInduction Furnaces

EU 003 Removed EIS 001 Hr 3321Lindberg NFGe 10/2500 4 Ton

5 FM Inductotherm CorelessFurnace #3

EU 004 Active PER 011 CE 015SV 030 (M) Hr 3321Inductotherm Linemelt 2500 KW 2.3 Ton

6 FM Inductotherm CorelessFurnace #3 - Furnace

EU 004 Active PER 012 CE 015SV 030 (M) Hr 3321Inductotherm Linemelt 2500 KW 2.3 Ton

7 High Pressure Molding LinePouring & Cooling

EU 005 Removed PER 011 Hr 3321Inductotherm Linemelt Inductopour 5.7 Ton

8 Match Blowmatic Molding LinePouring & Cooling

EU 006 Removed EIS 001 Hr 3321Beardsley & Piper 85B .63 Ton

9 High Pressure Molding LinePunchout

EU 007 Active PER 011 CE 018SV 041 (M) Hr 3321KW NA 8.5 Ton

10 High Pressure Molding LinePunchout - PressingEquipment

EU 007 Active PER 012 CE 018SV 041 (M) Hr 3321KW NA 8.5 Ton

11 FM Casting Conveying andCooling

EU 008 Active PER 011 CE 018SV 041 (M) Hr 3321General Kinematics NA 8.5 Ton

12 FM Casting Conveying andCooling - Conveyor

EU 008 Active PER 012 CE 018SV 041 (M) Hr 3321General Kinematics NA 8.5 Ton

13 Shotblast Cleaning of Castings#1

EU 009 Active PER 011 CE 002SV 004 (M) Hr 3321Wheelabrator 28 Cubic Feet 2.92 Ton

14 Shotblast Cleaning of Castings#1 - Abrasive Equipment

EU 009 Active PER 012 CE 002SV 004 (M) Hr 3321Wheelabrator 28 Cubic Feet 2.92 Ton

15 Tumble Cleaning of CastingsEU 010 Removed PER 011 SV 006 (M) Hr 3321Wheelabrator 14 Cubic Feet 6.33 Ton

16 Foundry Sand MullerEU 011 Active PER 011 CE 018SV 041 (M) Hr 3321Beardsley & Piper 85B 0.881 Ton

17 Foundry Sand Muller -Sanding Equipment

EU 011 Active PER 012 CE 018SV 041 (M) Hr 3321Beardsley & Piper 85B 0.881 Ton

18 Sand Receiving SiloEU 012 Active EIS 001 CE 005SV 007 (M) Hr 3321Custom 100 Ton 6 Ton

19 Sand Receiving Silo - Silo/BinEU 012 Active PER 012 CE 005SV 007 (M) Hr 3321Custom 100 Ton 6 Ton

Page 1 of 17 (a)

12 November, 2014 10:02


ID No. ElevatorType

BottleneckPct.Fuel/

SpaceHeat

Firing MethodAddedBy

(Action)

RemovalDate

InitialStartup

Date

Comm-ence

Const.Date

EmissionUnit

Status

1 EU 001 PER 011 01/01/197901/01/1979Active

2 EU 001 PER 012 01/01/197901/01/1979Active

3 EU 002 0PER 011 12/31/200401/01/197901/01/1979Removed

4 EU 003 EIS 001 12/31/199801/01/197901/01/1979Removed

5 EU 004 PER 011 11/01/199410/01/1994Active

6 EU 004 PER 012 11/01/199410/01/1994Active

7 EU 005 PER 011 12/31/200202/01/198801/01/1988Removed

8 EU 006 EIS 001 12/31/199802/01/199001/01/1990Removed

9 EU 007 PER 011 02/01/198601/01/1986Active

10 EU 007 PER 012 02/01/198601/01/1986Active

11 EU 008 PER 011 02/01/198601/01/1986Active

12 EU 008 PER 012 02/01/198601/01/1986Active

13 EU 009 PER 011 02/01/197901/01/1979Active

14 EU 009 PER 012 02/01/197901/01/1979Active

15 EU 010 PER 011 12/31/199802/01/197901/01/1979Removed

16 EU 011 PER 011 02/01/198801/01/1988Active

17 EU 011 PER 012 02/01/198801/01/1988Active

18 EU 012 EIS 001 01/01/197901/01/1979Active

19 EU 012 PER 012 01/01/197901/01/1979Active

Page 1 of 17 (b)

ST. PAUL, MN 55155-4194



12 November, 2014 10:02


MaxFuelInput

(mil Btu)


RetiredBy

(Action)


Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity


Max.Design

Capacity

MaximumDesign

Capacity


20 Sand Receiving SiloEU 013 Active PER 011 CE 006CE 015

SV 008 (M)SV 030 (P)

Hr 3321Custom 100 Ton 6 Ton

21 Sand Receiving Silo - Silo/BinEU 013 Active PER 012 CE 006CE 015

SV 008 (M)SV 030 (P)

Hr 3321Custom 100 Ton 6 Ton

22 Isocure Core MakingEU 014 Removed EIS 001 Hr 3321Shalco U180 CB .45 Ton

23 Isocure Core MakingEU 015 Removed EIS 001 Hr 3321Shalco 4-101 .45 Ton

224 Core OvenEU 016 Removed EIS 001 Hr 3321Despatch DO500 Type ILA1 .67 Ton

125 Core OvenEU 017 Removed EIS 001 Hr 3321Despatch DO100 .33 Ton

6.426 Gray Iron Chip DryerEU 018 Removed EIS 001 SV 013 (M) Hr 3321Lindberg RCD-4000 2 Ton

4.827 Gray Iron Heat Treating OvenEU 019 Removed PER 010 3321Johnston 4x16x4 Car Type

828 CO2 Core MakingEU 020 Removed EIS 001 Hr 3321Custom NA .25 Ton

29 Pepset Sand SystemEU 021 Removed EIS 003 SV 016 (M) Hr 3321NA NA 1.2 Ton

30 Pepset Mold Making SystemEU 022 Removed PER 003 Min 3321Strong Skott for mixer NA 3450 Ft3(s)

131 Aluminum Heat TreatingEU 023 Active PER 011 SV 018 (M) 3321Despatch NA

132 Aluminum Heat Treating -Other Combustion

EU 023 Active PER 012 SV 018 (M) 3321Despatch NA

5.06633 Aluminum Foundry CentralMelting Furnace

EU 024 Active PER 011 SV 019 (M) Hr 3321MPH ACM-2500-OP .83 Ton

5.06634 Aluminum Foundry CentralMelting Furnace - Furnace

EU 024 Active PER 012 SV 019 (M) Hr 3321MPH ACM-2500-OP .83 Ton

835 Aluminum Foundry HoldingCrucibles

EU 025 Removed PER 011 Hr 3321Lindberg NA .15 Ton

836 Aluminum Foundry HoldingFurnaces

EU 026 Active PER 011 SV 021 (P) Hr 3321F W Schafer NA .15 Ton

837 Aluminum Foundry HoldingFurnaces - Furnace

EU 026 Active PER 012 SV 021 (P) Hr 3321F W Schafer NA .15 Ton

38 Spraying Mold Release onLiqui-Forge Molds

EU 027 Removed EIS 001 SV 022 (M) Yr 3321NA NA 240000 Ft3

39 Cleaning Aluminum Castings(Cutting)

EU 028 Retired PER 011 Hr 3321Custom NA .83 Ton

5.240 Aluminum Chip DryingEU 029 Removed PER 011 SV 024 (M) Hr 3321Coreco NA 1 Ton

41 BoilerEU 030 Removed PER 011 3321Burnham

42 PlatingEU 031 Removed PER 011 Min 3321Clinton Supply Co NA 2500 Ft3(s)

Page 2 of 17 (a)

12 November, 2014 10:02


ID No. ElevatorType

BottleneckPct.Fuel/

SpaceHeat


(Action)

RemovalDate

InitialStartup

Date

Comm-ence

Const.Date

EmissionUnit

Status

20 EU 013 PER 011 01/01/197901/01/1979Active

21 EU 013 PER 012 01/01/197901/01/1979Active

22 EU 014 EIS 001 12/31/199801/01/197901/01/1979Removed

23 EU 015 EIS 001 12/31/199801/01/197901/01/1979Removed

24 EU 016 0EIS 001 12/31/199801/01/197901/01/1979Removed

25 EU 017 0EIS 001 12/31/199801/01/197901/01/1979Removed

26 EU 018 0EIS 001 12/31/199801/01/197901/01/1979Removed

27 EU 019 0PER 010 08/01/200301/01/197901/01/1979Removed

28 EU 020 0EIS 001 12/31/199801/01/197501/01/1975Removed

29 EU 021 EIS 003 12/31/199901/01/198001/01/1980Removed

30 EU 022 PER 003 10/01/199901/01/198001/01/1980Removed

31 EU 023 0PER 011 01/01/197501/01/1975Active

32 EU 023 0PER 012 01/01/197501/01/1975Active

33 EU 024 0PER 011 07/01/199005/15/1990Active

34 EU 024 0PER 012 07/01/199005/15/1990Active

35 EU 025 0PER 011 01/01/199801/01/196801/01/1968Removed

36 EU 026 0PER 011 01/01/197801/01/1978Active

37 EU 026 0PER 012 01/01/197801/01/1978Active

38 EU 027 EIS 001 12/31/199801/01/198601/01/1986Removed

39 EU 028 PER 011 01/01/196001/01/1960Retired

40 EU 029 0PER 011 02/01/200301/01/197801/01/1978Removed

41 EU 030 0PER 011 02/28/200703/01/199903/01/1999Removed

42 EU 031 PER 011 02/28/200701/01/194501/01/1945Removed

Page 2 of 17 (b)

ST. PAUL, MN 55155-4194



12 November, 2014 10:02


MaxFuelInput

(mil Btu)


RetiredBy

(Action)


Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity


Max.Design

Capacity

MaximumDesign

Capacity


1.743 BoilerEU 032 Removed PER 010 SV 025 (M) 3321Weil-McLain LBG-10

.3844 BoilerEU 033 Active PER 011 SV 028 (M) Hr Heat3321Bryan CL-24-ST .38 Mmbtu

.3845 Boiler - BoilerEU 033 Active PER 012 SV 028 (M) Hr Heat3321Bryan CL-24-ST .38 Mmbtu

.4546 BoilerEU 034 Active PER 011 SV 029 (M) Hr Heat3321Weil-McLain LG-6 .45 Mmbtu

.4547 Boiler - BoilerEU 034 Active PER 012 SV 029 (M) Hr Heat3321Weil-McLain LG-6 .45 Mmbtu


EU 035 Active PER 011 CE 015SV 030 (M) Hr 3321ABB IFM-6 7.00 Ton



50 High Pressure Molding LinePouring & Cooling

EU 036 Active PER 011 CE 015SV 030 (M) Hr 3321Kunkel Wagner EPM 8.50 Ton

51 High Pressure Molding LinePouring & Cooling - PouringEquipment

EU 036 Active PER 012 CE 015SV 030 (M) Hr 3321Kunkel Wagner EPM 8.50 Ton

52 Tumble Cleaning of CastingsEU 037 Removed PER 010 CE 002SV 004 Hr 3321Didion 16.25 Ton

0.353 Aluminum Foundry HeatTreating Oven - SOW

EU 038 Active PER 011 SV 031 (M) Hr Heat3321Despatch PWE3-15-16 0.3 Mmbtu

0.354 Aluminum Foundry HeatTreating Oven - SOW -Dryer/Oven, unknown firingmethod

EU 038 Active PER 012 SV 031 (M) Hr Heat3321Despatch PWE3-15-16 0.3 Mmbtu

55 BoilerEU 039 Removed PER 011 3321Slant/Fin GG399

0.7556 Sleeve Machine Shop TreatingOven

EU 040 Active PER 011 SV 032 (M) Hr Heat3321Despatch PSD3-495-G 0.75 Mmbtu

0.7557 Sleeve Machine Shop TreatingOven - Other Emission Unit

EU 040 Active PER 012 SV 032 (M) Hr Heat3321Despatch PSD3-495-G 0.75 Mmbtu





60 Air Blowout Gun Line 1EU 042 Active PER 011 CE 015SV 030 (M) Hr 3321Guardair 75XT 32.34 Lb

61 Air Blowout Gun Line 1 -Blowing Equipment

EU 042 Active PER 012 CE 015SV 030 (M) Hr 3321Guardair 75XT 32.34 Lb

62 Coating Application Wand Line1

EU 043 Active PER 011 SV 033 (M) Hr 3321Federal-Mogul 70140200 32.34 Lb

Page 3 of 17 (a)

12 November, 2014 10:02


ID No. ElevatorType

BottleneckPct.Fuel/

SpaceHeat


(Action)

RemovalDate

InitialStartup

Date

Comm-ence

Const.Date

EmissionUnit

Status

43 EU 032 100PER 010 12/31/199801/01/194501/01/1945Removed

44 EU 033 100PER 011 01/01/197001/01/1970Active

45 EU 033 100PER 012 01/01/197001/01/1970Active

46 EU 034 100PER 011 01/01/194301/01/1943Active

47 EU 034 100PER 012 01/01/194301/01/1943Active

48 EU 035 PER 011 12/01/199906/29/1999Active

49 EU 035 PER 012 12/01/199906/29/1999Active

50 EU 036 PER 011 12/01/199906/29/1999Active

51 EU 036 PER 012 12/01/199906/29/1999Active

52 EU 037 PER 010 12/31/2002Removed

53 EU 038 PER 011 01/15/200101/01/2001Active

54 EU 038 PER 012 01/15/200101/01/2001Active

55 EU 039 100PER 011 02/28/2007Removed

56 EU 040 PER 011Active

57 EU 040 PER 012Active

58 EU 041 PER 011 12/01/199906/29/1999Active

59 EU 041 PER 012 12/01/199906/29/1999Active

60 EU 042 PER 011 09/01/200006/26/2000Active

61 EU 042 PER 012 09/01/200006/26/2000Active

62 EU 043 PER 011 09/01/200006/26/2000Active

Page 3 of 17 (b)

ST. PAUL, MN 55155-4194



12 November, 2014 10:02


MaxFuelInput

(mil Btu)


RetiredBy

(Action)


Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity


Max.Design

Capacity

MaximumDesign

Capacity


63 Coating Application Wand Line1 - Spray Booth/Coating Line

EU 043 Active PER 012 SV 033 (M) Hr 3321Federal-Mogul 70140200 32.34 Lb

64 Line #1 Long Tube AbrasiveBlasting Unit

EU 044 Active PER 011 CE 015SV 030 (M) Hr 3321US Filter/Wheelabrator 6 1.75 Ton

65 Line #1 Long Tube AbrasiveBlasting Unit - AbrasiveEquipment


66 Abrasive Blasting Unit #2EU 045 Removed PER 011 Hr Casting3321US Filter/Wheelabrator 7 26 Each

67 Abrasive Blasting Unit #3EU 046 Removed PER 011 Hr Casting3321US Filter/Wheelabrator 7 26 Each

68 Casting Cutting Station 1-1EU 047 Active PER 011 CE 015SV 030 (M) Hr 3321Yasec Yamashino Seik OL 0.35 Ton

69 Casting Cutting Station 1-1 -Casting Equipment

EU 047 Active PER 012 CE 015SV 030 (M) Hr 3321Yasec Yamashino Seik OL 0.35 Ton








75 Casting Cutting Station 1-4EU 050 Removed PER 012 Hr 3321Yasec Yamashino Seik OL 0.35 Ton



78 Machining Lathe 1-1EU 052 Active PER 011 CE 015SV 030 (M) Hr 3321Okuma Lathes LU-25 0.3182 Ton

79 Machining Lathe 1-1 -Machining Equipment

EU 052 Active PER 012 CE 016SV 039 (M) Hr 3321Okuma Lathes LU-25 0.3182 Ton








Page 4 of 17 (a)

12 November, 2014 10:02


ID No. ElevatorType

BottleneckPct.Fuel/

SpaceHeat


(Action)

RemovalDate

InitialStartup

Date

Comm-ence

Const.Date

EmissionUnit

Status

63 EU 043 PER 012 09/01/200006/26/2000Active

64 EU 044 PER 011 09/01/200006/26/2000Active

65 EU 044 PER 012 09/01/200006/26/2000Active

66 EU 045 PER 011 11/30/200709/01/200006/26/2000Removed

67 EU 046 PER 011 11/30/200709/01/200006/26/2000Removed

68 EU 047 PER 011 09/01/200006/26/2000Active

69 EU 047 PER 012 09/01/200006/26/2000Active

70 EU 048 PER 011 09/01/200006/26/2000Active

71 EU 048 PER 012 09/01/200006/26/2000Active

72 EU 049 PER 011 09/01/200006/26/2000Active

73 EU 049 PER 012 09/01/200006/26/2000Active

74 EU 050 PER 011 09/01/200006/26/2000Active

75 EU 050 PER 012 09/01/200006/26/2000Removed

76 EU 051 PER 011 09/01/200006/26/2000Active

77 EU 051 PER 012 09/01/200006/26/2000Removed

78 EU 052 PER 011 09/01/200006/26/2000Active

79 EU 052 PER 012 09/01/200006/26/2000Active

80 EU 053 PER 011 09/01/200006/26/2000Active

81 EU 053 PER 012 09/01/200006/26/2000Active

82 EU 054 PER 011 09/01/200006/26/2000Active

83 EU 054 PER 012 09/01/200006/26/2000Active

84 EU 055 PER 011 09/01/200006/26/2000Active

Page 4 of 17 (b)

ST. PAUL, MN 55155-4194



12 November, 2014 10:02


MaxFuelInput

(mil Btu)


RetiredBy

(Action)


Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity


Max.Design

Capacity

MaximumDesign

Capacity




86 Brushing Unit Machine Line1-1

EU 056 Active PER 011 CE 016SV 039 (M) Hr 3321Yoshida Unit 1 0.875 Ton

87 Brushing Unit Machine Line1-1 - Abrasive Equipment






90 Line #1 Casting FinishingStation #7

EU 058 Removed PER 011 Hr 3321Okuma Lathes LR25 97 Each

0.158791 Die Heater Burner 1-1EU 059 Active PER 011 SV 035 (M) Hr Heat3321North American Mfg. C ISD-8312 0.1587 Mmbtu

0.158792 Die Heater Burner 1-1 -Process Heater

EU 059 Active PER 012 SV 035 (M) Hr Heat3321North American Mfg. C ISD-8312 0.1587 Mmbtu




















Page 5 of 17 (a)

12 November, 2014 10:02


ID No. ElevatorType

BottleneckPct.Fuel/

SpaceHeat


(Action)

RemovalDate

InitialStartup

Date

Comm-ence

Const.Date

EmissionUnit

Status

85 EU 055 PER 012 09/01/200006/26/2000Active

86 EU 056 PER 011 09/01/200006/26/2000Active

87 EU 056 PER 012 09/01/200006/26/2000Active

88 EU 057 PER 011 09/01/200006/26/2000Active

89 EU 057 PER 012 09/01/200006/26/2000Active

90 EU 058 PER 011 11/30/200709/01/200006/26/2000Removed

91 EU 059 PER 011 09/01/200006/26/2000Active

92 EU 059 PER 012 09/01/200006/26/2000Active

93 EU 060 PER 011 09/01/200006/26/2000Active

94 EU 060 PER 012 09/01/200006/26/2000Active

95 EU 061 PER 011 09/01/200006/26/2000Active

96 EU 061 PER 012 09/01/200006/26/2000Active

97 EU 062 PER 011 09/01/200006/26/2000Active

98 EU 062 PER 012 09/01/200006/26/2000Active

99 EU 063 PER 011 09/01/200006/26/2000Active

100 EU 063 PER 012 09/01/200006/26/2000Active

101 EU 064 PER 011 09/01/200006/26/2000Active

102 EU 064 PER 012 09/01/200006/26/2000Active

103 EU 065 PER 011 09/01/200006/26/2000Active

104 EU 065 PER 012 09/01/200006/26/2000Active

105 EU 066 PER 011 09/01/200006/26/2000Active

Page 5 of 17 (b)

ST. PAUL, MN 55155-4194



12 November, 2014 10:02


MaxFuelInput

(mil Btu)


RetiredBy

(Action)


Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity


Max.Design

Capacity

MaximumDesign

Capacity














EU 070 Active PER 011 CE 016SV 039 (M) Hr 3321Federal-Mogul 70140200 32.34 Lb



115 Line #2 Abrasive Blasting Unit#1 Long Tube


116 Line #2 Abrasive Blasting Unit#1 Long Tube - AbrasiveEquipment


117 Line #2 Abrasive Blasting Unit#2

EU 072 Removed PER 011 Hr Casting3321US Filter/Wheelabrator 7 26 Each


EU 073 Removed PER 011 Hr Casting3321US Filter/Wheelabrator 7 26 Each












Page 6 of 17 (a)

12 November, 2014 10:02


ID No. ElevatorType

BottleneckPct.Fuel/

SpaceHeat


(Action)

RemovalDate

InitialStartup

Date

Comm-ence

Const.Date

EmissionUnit

Status

106 EU 066 PER 012 09/01/200006/26/2000Active

107 EU 067 PER 011 09/01/200006/26/2000Active

108 EU 067 PER 012 09/01/200006/26/2000Active

109 EU 068 PER 011 09/01/200006/26/2000Active

110 EU 068 PER 012 09/01/200006/26/2000Active

111 EU 069 PER 011 12/01/200304/01/2003Active

112 EU 069 PER 012 12/01/200304/01/2003Active

113 EU 070 PER 011 12/01/200304/01/2003Active

114 EU 070 PER 012 12/01/200304/01/2003Active

115 EU 071 PER 011 12/01/200304/01/2003Active

116 EU 071 PER 012 12/01/200304/01/2003Active

117 EU 072 PER 011 11/30/200712/01/200304/01/2003Removed

118 EU 073 PER 011 11/30/200712/01/200304/01/2003Removed

119 EU 074 PER 011 12/01/200304/01/2003Active

120 EU 074 PER 012 12/01/200304/01/2003Active

121 EU 075 PER 011 12/01/200304/01/2003Active

122 EU 075 PER 012 12/01/200304/01/2003Active

123 EU 076 PER 011 12/01/200304/01/2003Active

124 EU 076 PER 012 12/01/200304/01/2003Active

125 EU 077 PER 011 12/01/200304/01/2003Active

126 EU 077 PER 012 12/01/200304/01/2003Removed

Page 6 of 17 (b)

ST. PAUL, MN 55155-4194



12 November, 2014 10:02


MaxFuelInput

(mil Btu)


RetiredBy

(Action)


Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity


Max.Design

Capacity

MaximumDesign

Capacity





















139 LIne #2 Casting FinishingStation #6


140 Line #2 Casting FinishingStation #7


0.5141 Die Heater Burner 2-1EU 086 Active PER 011 SV 036 (M) Hr Heat3321Applied Thermo Techno Custom 0.5 Mmbtu


EU 086 Active PER 012 SV 036 (M) Hr Heat3321Applied Thermo Techno Custom 0.5 Mmbtu







0.25147 Die Heater Burner 2-4EU 089 Removed PER 011 Hr Heat3321Applied Thermo Techno Custom 250000 Btu


Page 7 of 17 (a)

12 November, 2014 10:02


ID No. ElevatorType

BottleneckPct.Fuel/

SpaceHeat


(Action)

RemovalDate

InitialStartup

Date

Comm-ence

Const.Date

EmissionUnit

Status

127 EU 078 PER 011 12/01/200304/01/2003Active

128 EU 078 PER 012 12/01/200304/01/2003Removed

129 EU 079 PER 011 12/01/200304/01/2003Active

130 EU 079 PER 012 12/01/200304/01/2003Active

131 EU 080 PER 011 12/01/200304/01/2003Active

132 EU 080 PER 012 12/01/200304/01/2003Active

133 EU 081 PER 011 12/01/200304/01/2003Active

134 EU 081 PER 012 12/01/200304/01/2003Active

135 EU 082 PER 011 12/01/200304/01/2003Active

136 EU 082 PER 012 12/01/200304/01/2003Active

137 EU 083 PER 011 12/01/200304/01/2003Active

138 EU 083 PER 012 12/01/200304/01/2003Active

139 EU 084 PER 011 11/30/200712/01/200304/01/2003Removed

140 EU 085 PER 011 11/30/200712/01/200304/01/2003Removed

141 EU 086 PER 011 12/01/200304/01/2003Active

142 EU 086 PER 012 12/01/200304/01/2003Active

143 EU 087 PER 011 12/01/200304/01/2003Active

144 EU 087 PER 012 12/01/200304/01/2003Active

145 EU 088 PER 011 12/01/200304/01/2003Active

146 EU 088 PER 012 12/01/200304/01/2003Active

147 EU 089 PER 011 12/01/200304/01/2003Removed

148 EU 090 PER 011 12/01/200304/01/2003Removed

Page 7 of 17 (b)

ST. PAUL, MN 55155-4194



12 November, 2014 10:02


MaxFuelInput

(mil Btu)


RetiredBy

(Action)


Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity


Max.Design

Capacity

MaximumDesign

Capacity







154 Line #1 Centrifugal Pouring &Cooling

EU 096 Active PER 011 CE 015SV 030 (M) Hr 3321Duca Custom 1.75 Ton

155 Line #1 Centrifugal Pouring &Cooling - Pouring Equipment

EU 096 Active PER 012 CE 015SV 030 (M) Hr 3321Duca Custom 1.75 Ton


EU 097 Active PER 011 CE 016SV 039 (M) Hr 3321Otani Custom 1.75 Ton


EU 097 Active PER 012 CE 016SV 039 (M) Hr 3321Otani Custom 1.75 Ton

158 JV Charge Handling BridgeCrane

EU 098 Active PER 011 SV 044 (M) Hr 3321Konecranes 10 ton 3.50 Ton

159 JV Charge Handling BridgeCrane - Material HandlingEquipment

EU 098 Active PER 012 SV 044 (M) Hr 3321Konecranes 10 ton 3.50 Ton


EU 099 Active PER 011 CE 017SV 040 (M) Hr 3321Inductotherm 2000 KW VIP DT-2 2.31 Ton








EU 101 Active PER 011 CE 019SV 045 (M) Hr 3321ABP Induction Minipour 3.5 3.5 Ton


EU 101 Active PER 012 CE 019SV 045 (M) Hr 3321ABP Induction Minipour 3.5 3.5 Ton






Page 8 of 17 (a)

12 November, 2014 10:02


ID No. ElevatorType

BottleneckPct.Fuel/

SpaceHeat


(Action)

RemovalDate

InitialStartup

Date

Comm-ence

Const.Date

EmissionUnit

Status

149 EU 091 PER 011 12/01/200304/01/2003Removed

150 EU 092 PER 011 12/01/200304/01/2003Removed

151 EU 093 PER 011 12/01/200304/01/2003Removed

152 EU 094 PER 011 12/01/200304/01/2003Removed

153 EU 095 PER 011 12/01/200304/01/2003Removed

154 EU 096 PER 011 12/01/200304/01/2003Active

155 EU 096 PER 012 12/01/200304/01/2003Active

156 EU 097 PER 011 12/01/200304/01/2003Active

157 EU 097 PER 012 12/01/200304/01/2003Active

158 EU 098 PER 011 12/01/200304/01/2003Active

159 EU 098 PER 012 12/01/200304/01/2003Active

160 EU 099 PER 011 12/01/200304/01/2003Active

161 EU 099 PER 012 12/01/200304/01/2003Active

162 EU 100 PER 011 12/01/200304/01/2003Active

163 EU 100 PER 012 12/01/200304/01/2003Active

164 EU 101 PER 011 09/01/200601/01/2006Active

165 EU 101 PER 012 09/01/200601/01/2006Active

166 EU 102 PER 011 10/01/200601/01/2005Active

167 EU 102 PER 012 10/01/200601/01/2005Active

168 EU 103 PER 011 10/01/200601/01/2005Active

Page 8 of 17 (b)

ST. PAUL, MN 55155-4194



12 November, 2014 10:02


MaxFuelInput

(mil Btu)


RetiredBy

(Action)


Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity


Max.Design

Capacity

MaximumDesign

Capacity




170 Line #3 Abrasive Blasting Unit#1 Long Tube


171 Line #3 Abrasive Blasting Unit#1 Long Tube - AbrasiveEquipment



EU 105 Removed PER 011 Hr 3321US Filter/Wheelabrator 7 338 Each


EU 106 Removed PER 011 Hr 3321US Filter/Wheelabrator 7 338 Each
















184 Machining Lathe 5-1EU 112 Active PER 011 CE 019SV 045 (M) Hr 3321Okuma LU-400 0.3182 Ton


EU 112 Active PER 012 CE 019SV 045 (M) Hr 3321Okuma LU-400 0.3182 Ton







Page 9 of 17 (a)

12 November, 2014 10:02


ID No. ElevatorType

BottleneckPct.Fuel/

SpaceHeat


(Action)

RemovalDate

InitialStartup

Date

Comm-ence

Const.Date

EmissionUnit

Status

169 EU 103 PER 012 10/01/200601/01/2005Active

170 EU 104 PER 011 10/01/200601/01/2005Active

171 EU 104 PER 012 10/01/200601/01/2005Active

172 EU 105 PER 011 11/30/200710/01/200601/01/2005Removed

173 EU 106 PER 011 11/30/200710/01/200601/01/2005Removed

174 EU 107 PER 011 09/01/200601/01/2006Active

175 EU 107 PER 012 09/01/200601/01/2006Active

176 EU 108 PER 011 09/01/200601/01/2006Active

177 EU 108 PER 012 09/01/200601/01/2006Active

178 EU 109 PER 011 09/01/200601/01/2006Active

179 EU 109 PER 012 09/01/200601/01/2006Active

180 EU 110 PER 011 09/01/200601/01/2006Active

181 EU 110 PER 012 09/01/200601/01/2006Active

182 EU 111 PER 011 09/01/200601/01/2006Active

183 EU 111 PER 012 09/01/200601/01/2006Active

184 EU 112 PER 011 09/01/200601/01/2006Active

185 EU 112 PER 012 09/01/200601/01/2006Active

186 EU 113 PER 011 09/01/200601/01/2006Active

187 EU 113 PER 012 09/01/200601/01/2006Active

188 EU 114 PER 011 09/01/200601/01/2006Active

189 EU 114 PER 012 09/01/200601/01/2006Active

Page 9 of 17 (b)

ST. PAUL, MN 55155-4194



12 November, 2014 10:02


MaxFuelInput

(mil Btu)


RetiredBy

(Action)


Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity


Max.Design

Capacity

MaximumDesign

Capacity














0.595248198 Die Heater Burner 3-1EU 119 Active PER 011 SV 043 (M) Hr Heat3321Yamashino Seiki Co. LT OP-8 595248 Btu


EU 119 Active PER 012 SV 043 (M) Hr Heat3321Yamashino Seiki Co. LT OP-8 595248 Btu







.25204 Die Heater Burner 3-4EU 122 Removed PER 011 Hr Heat3321Yamashino Seiki Co. LT OP-8 .25 Mmbtu








EU 129 Active PER 011 CE 002SV 004 (M) Hr 3321wheelabrator 28 cubic feet 2.92 Ton



Page 10 of 17 (a)

12 November, 2014 10:02


ID No. ElevatorType

BottleneckPct.Fuel/

SpaceHeat


(Action)

RemovalDate

InitialStartup

Date

Comm-ence

Const.Date

EmissionUnit

Status

190 EU 115 PER 011 09/01/200601/01/2006Active

191 EU 115 PER 012 09/01/200601/01/2006Active

192 EU 116 PER 011 09/01/200601/01/2006Active

193 EU 116 PER 012 09/01/200601/01/2006Active

194 EU 117 PER 011 09/01/200601/01/2006Active

195 EU 117 PER 012 09/01/200601/01/2006Active

196 EU 118 PER 011 09/01/200601/01/2006Active

197 EU 118 PER 012 09/01/200601/01/2006Active

198 EU 119 PER 011 10/01/200601/01/2005Active

199 EU 119 PER 012 10/01/200601/01/2005Active

200 EU 120 PER 011 10/01/200601/01/2005Active

201 EU 120 PER 012 10/01/200601/01/2005Active

202 EU 121 PER 011 10/01/200601/01/2005Active

203 EU 121 PER 012 10/01/200601/01/2005Active

204 EU 122 PER 011 10/01/200601/01/2005Removed

205 EU 123 PER 011 10/01/200601/01/2005Removed

206 EU 124 PER 011 10/01/200601/01/2005Removed

207 EU 125 PER 011 10/01/200601/01/2005Removed

208 EU 126 PER 011 10/01/200601/01/2005Removed

209 EU 127 PER 011 10/01/200601/01/2005Removed

210 EU 128 PER 011 10/01/200601/01/2005Removed

211 EU 129 PER 011 01/31/200001/01/2000Active

212 EU 129 PER 012 01/31/200001/01/2000Active

Page 10 of 17 (b)

ST. PAUL, MN 55155-4194



12 November, 2014 10:02


MaxFuelInput

(mil Btu)


RetiredBy

(Action)


Status

AddedBy

(Action)

ControlEquip.

ID No(s).

Stack/Vent

ID No(s).

OperatorID

for Item

Insignif-icant

Activity


Max.Design

Capacity

MaximumDesign

Capacity






215 Line #3 Charge Handling &Conveyor

EU 131 Active PER 011 SV 044 (M) Hr 3321Kinergy Corp KDF-30/48-EHD 3.5 Ton

216 Line #3 Charge Handling &Conveyor - Conveyor

EU 131 Active PE

technical support document for draft air …technical support document, permit action number:...

Documents