tools installation time support · for easier installation, the top should be installed at a...

P1 - 54723 - Rev. O 1114 Installation Instructions - Supertop NX © 2014 Bestop, Inc.

Installation InstructionsSupertop NX

Vehicle Application:Jeep Wrangler Unlimited2007-currentPart Number 54723

Installation Tips

Before you begin installing your new Supertop NX, please read all the instructions thoroughly.

For a smooth fit:For easier installation, the top should be installed at a temperature above 72° F. Below this temperature, the fabric may contract an inch or more, making it difficult to fit the vehicle.

It is normal for the fabric to contract and wrinkle when stored in the shipping carton. Within a few days after installation, the fabric will relax and the wrinkles will disappear.

Installation TimeTools

Skill Level

4 Hours

3 - Moderately Difficult

Drill-Driver &#2 Phillips Bit

#2 PhillipsScrewdriver

T30 TorxDriver

AdjustableWrench

SafetyGlasses

Vise-Grips

Support

We’re here to help!Go to www.Bestop.com and

click “Contact Us”

See a video showinginstallation of this top atwww.bestop.com/video


All Sections Hardware and Fasteners

Parts List- Required parts for each installation section - Page number in Installation Guide

Multiple Pages


Section 1 Cable Guide Brackets & Rear Door Rails Page 6 of Guide


Bow Mount ScrewQty. 4Part # 308.64

M5 x 16 ScrewQty. 6Part # 459.45

Pan HeadWasher ScrewQty. 31Part # 393.79

M5 x 30 ScrewQty. 2Part # 308.87

M5 Nylock NutQty. 8Part # 308.62

Plastic BushingQty. 8Part # 473.40

Pivot Knuckle ScrewQty. 2Part # 308.65

Cable Guide BracketQty. 1 Part # 482.83 - Left

Cable Guide Bracket Qty. 1 Part # 482.82 - Right

Rear Door RailQty. 1 479.88 Right

Rear Door RailQty. 1 479.89 Left


Sections 2 & 3 Knobs and Front Door Rails


Pages 7& 8 of Guide


Sections 4 & 5 Top Arches & Bow Mount Brackets Pages 9 & 10 of Guide


M8 x 30mm KnobQty. 2Part # 480.22

M8 x 75mm KnobQty. 4Part # 478.90

Front Door RailQty. 1 Part # 479.87 - Left

Front Door RailQty. 1 Part # 479.86 - Right

Front Top ArchQty. 1 Part #486.55

Rear Top ArchQty. 1 Part #486.56

Bow Mount BracketQty. 1Part # 492.93 - Left

Bow Mount BracketQty. 1Part # 492.92 - Right

UpUp


Sections 6 & 7 Tailgate Bar Mounts & Side Bows


Pages 11, 12 &13 of Guide


Sections 8, 9 &10 #3 Bow, #4 Bow & Stay Strap Pages 14, 15 &16 of Guide


Tailgate Bar MountQty. 1Part # 488.47 - Left

Tailgate Bar MountQty. 1Part # 488.46 - Right

Side BowQty. 1Part # 492.89 - Left

Side BowQty. 1Part # 492.90 - Right

#3 Bow AssemblyQty. 1Part # 486.38


Stay StrapQty. 2Part # 456.32


Sections 12 & 16 #2 Bow Assembly & Foam Seals


Pages 18 & 22 of Guide


Section 23 Tailgate Bar & Strap Kit Pages 29 to 33 of Guide


#2 Bow AssemblyQty. 1 Part # 455.46

Foam Tape StripsQty. 2Part # 417.43

Foam SealsQty. 1 per sidePart # 457.76 (R) & 457.77(L)

Tailgate BarQty. 1 Part #489.46

Strap KitQty. 1 Part #413.09

Deck, Header Assembly, & Fabric Top

Right Side Window

Left Side Window

Rear Window

Section 1 Install Cable Guide Brackets in Rear Door Rails


Page 6

Attach the Right Cable Guide Bracket to the Right Rear Door Rail using two M5 x 16 screws and two M5 Nylock nuts.

Repeat for left side.

Step 1

Right Side

Step 1 482.82 479.88

M5 x 16 ScrewQty. 2 per sidePart # 459.45

Cable Guide Bracket - LeftQty. 1 Part # 482.83

Cable Guide Bracket - RightQty. 1 Part # 482.82

Hardware

M5 Nylock NutQty. 2 per sidePart # 308.62

Rear Door RailQty. 1 per side 479.88 Right (shown)479.89 Left

Section 2 Install Rear Door Rails


Page 7

Step 1Locate the Right Rear Door Rail. Attach the Right Rear Door Rail assembly to the Jeep belt rail behind the right rear door, inserting the alignment pin on the bottom of the Door Rail Assembly into the hole in the top of the belt rail.


Secure Left and Right Rear Door Rails to the Jeep Sport Bar using (1) Long M8x75mm Knob per side. The knobs go through the tab at the rear of each Rear Door Rail, and screw into the threaded holes in the top of the sport bar.

Step 2

Step 1 Step 2479.88 assembly

Right Side

Right Side

M8 x 75mm KnobQty. 1 per sidePart # 478.90

Rear Door RailsQty. 1 per side479.88 Right (shown)479.89 Left

Hardware

Section 3 Install Front Door Rails


Page 8

Step 1Attach the Right Front Door Rail to the Jeep sport bar, aligning the hole and slot in the tabs on the Front Door Rails with the threaded hole on the top of the sport bar, and with the slotted tab on the Rear Door Rail.

Repeat for the left side, using the Left Front Door Rail.

Secure the Front Door Rails to the sport bar using (1) M8x30mm Short Knob at the rear, and (1) M8x75mm Long Knob at the front. Secure the front of each Front Door Rail first, and leave both knobs slightly loose until after installing Top Arches, in Section 4.

Step 2

Step 1 Step 2479.86 (Right) 479.86 (Left)

Right Side

Right SideM8 x 30mm KnobQty. 1 per sidePart # 480.22

M8 x 75mm KnobQty. 1 per sidePart # 478.90

Hardware

Section 4 Install Top Arches


Page 9

Step 1Insert the Rear Top Arch into the vertical slotted tab on the Rear Door Rail. Insert one end, and flex the bow to insert the other end into the tabbed slot on the opposite side of the Jeep.

Repeat for Front Top Arch, inserting one end into the vertical tabbed slot in the Front Door Rail, and flexing to insert the other end into the tabbed slot on the opposite side of the Jeep.

Remove the protective peel-off strip on the top surface of each Top Arch.

Tighten all three knobs on the Front and Rear Door Rails, on both sides of the Jeep.

Step 2

Step 1 Step 2486.56 Rear Top Arch 486.55 Front Top Arch

Right Side - Rear

Right Side - Front

Front Top ArchQty. 1 Part #486.55

Rear Top ArchQty. 1 Part #486.56

Hardware

486.56 486.55

Section 5 Install Bow Mount Brackets


Page 10

Step 1Unzip the protective cover on the rear sport bar down-tubes and locate the two threaded holes on the underside of each sport bar down-tube.

Screw the Right Bow-Mount Support Bracket to the right-side sport bar down-tube using (2) Bow-Mount Screws.

Screw the Left Bow-Mount Support Bracket to the left-side sport bar down-tube using (2) Bow-Mount Screws.

Replace the sport bar protective cover, making sure that the Bow Mount Brackets stick out through the openings in the cover.

Step 2

Step 1 491.48 (Right)

Up

Hardware

Bow Mount ScrewQty. 2 per sidePart # 308.64

Left Bow Mount BracketQty. 1Part # 492.93

Right Bow Mount BracketQty. 1Part # 492.92

UpUp

Right Side


Section 6 Install Tailgate Bar Mounts Page 11

Step 1Locate the left and right Tailgate Bar Mounts. Each mount snaps onto the Jeep belt rail just outboard of the tailgate opening.

Snap each mount into place by hooking the inner catch portion of the mount under the belt rail on the inside, and then rolling the mount downward until it snaps into place under the bottom edge of the outside belt rail.


1

2

Hardware

Tailgate Bar Mount - LeftQty. 1Part # 488.47

Tailgate Bar Mount - RightQty. 1Part # 488.46

Right Side

Section 7 Attach Side Bows to Header/Fabric Assembly Page 12


Step 1Lay the Header/Fabric Assembly out with inside of fabric facing up. You may want to use the shipping box to keep the fabric off the ground.

Remove and set aside the two screws holding the protective flap down on the inside of the header. Fold the protective flap back to expose the screw holes used for attaching the Right Side Bow.

Repeat on left side of Header/Fabric Assembly.

Step 1 Header/Fabric Assembly

Right Side

1

2

Left Side BowQty. 1Part # 492.89

Right Side BowQty. 1Part # 492.90

Hardware#2 Bow BracketsFace In

Section 7 Attach Side Bows to Header/Fabric Assembly (cont.) Page 13


Step 2Insert the end of the Right Side Bow into the hole in the right side of the Header/Fabric Assembly, aligning the two holes in the tubing with the two holes in the header. Make sure that the #2 Bow Bracket faces in. Secure the Right Side Bow in place with (4) #8 x 1/2” Pan Head Washer Screws:two from the underside of the Header/Fabric assembly, and two from the topside.

Repeat on left side, using Left Side Bow.

Step 3Replace the protective flaps on both sides, and re-insert the screws you set aside, two for each side.

Step 3


Header/Fabric Assembly

1

2

Right Underside

2

1

Right Underside

Step 2 (cont.)

3

Right Topside

Hardware

Pan HeadWasher ScrewQty. 4 per sidePart # 393.79

Section 8 Attach #3 Bow to Bow Mount Brackets Page 14


Step 1Locate the #3 Bow Assembly. Release the spring-loaded catch at the end of each bow leg by pulling out on the knob.

Slide the slotted end of the catch over the top portion of the Bow Mount Bracket, so that it snaps into place in the top slotted hole in the Bow Mount Bracket.

Step 1 Step 2486.38 #3 Bow Assembly

12

Right Side Right Side

Hardware


Section 9 Attach #4 Bow to Bow Mount Brackets


Step 1Locate the #4 Bow Assembly. Release the spring-loaded catch at the end of each bow leg by pulling out on the knob.

Slide the slotted end of the catch over the lower portion of the Bow Mount Bracket, so that it snaps into place in the bottom hole in the Bow Mount Bracket.

Step 1 Step 2486.39 #4 Bow Assembly

1

2


Hardware



Page 16Section 10 Attach Stay Straps to #3 and #4 Bows

Step 1Position Stay Strap as shown, with square-cut end at front. Attach the Stay Strap to the top of the right side of the #3 Bow, using (2) #8x1/2” Pan Head Washer Screws, and the pre-drilled holes in the #3 Bow.

Repeat for left side Stay Strap.

Step 2Lift up the #4 Bow, and wrap the angled-cut end of the Stay Strap around the end of the #4 Bow. Wrap the Stay Strap over the top of the tubing, and fasten it on the underside of the tubing, using (3) #8 x1/2” Pan Head Washer Screws, and the pre-drilled holes on the underside of the #4 Bow.

Repeat for left side Stay Strap.

Step 1 Step 2456.32 Stay Strap

Right Side

Right Side

1

2

Hardware

Pan HeadWasher ScrewQty. 5 per sidePart # 393.79

Stay StrapQty. 1 per sidePart # 456.32


Page 17Section 11 Place Fabric /Header /Side Bow Assembly onto Jeep

Step 1Lift fabric and Header Assembly onto top of Jeep, with Header sitting on top of Jeep windshield, and fabric draped forward over Jeep hood.

You may want to protect the finish of the Jeep by putting a blanket across the Jeep hood.

Extend the Side Bows out straight and lay the Side Bows on top of the Door Rails.

Step 1 Fabric /Header /Side Bow Assembly

Right Side

Section 12 Attach #2 Bow Assembly to Fabric /Header /Side Bow Assembly


Step 1

Step 2

Step 3

Extend the legs of the #2 Bow and orient the front legs with the J-bracket on the front inside of each Side Bow.

Attach the front legs to the Side Bows with (1) M5x16 Machine Screw, (2) bushings, and (1) M5 Nylock Nut per side.

Attach the rear legs of the #2 Bow to the Side Bows using (1) M5x30 Machine Screw, (2) Bushings, and (1) M5 Nylock Nut per side.

Step 1 Step 2

Step 3

455.46 #2 Bow Assembly

Right Side

1

3

Right Side, Front Looking frominside the Jeep

Right Side, RearLooking frominside the Jeep

2

Hardware

#2 Bow AssemblyQty. 1 Part # 455.46


M5 Nylock NutQty. 2 per sidePart # 308.62

Plastic BushingQty. 4 per sidePart # 473.40


Section 13 Slide Header /Side Bow Assembly into place in Door Rails


Step 1Align the Header-Bow Assembly in the tracks in the top of the Door Rails. The plastic track guide on the Side Bow Assembly must be located to the rear of the spring-catch, and in position to slide forward over the vertical plastic rib in the top of the Rear Door Rail

Step 2Slide the whole Header/Side Bow Assembly forward in the tracks in the top of the Door Rails, until the button on the inside of each plastic track guide on the Side Bows slips under the spring-catch and latches in place.

Step 1 Step 2Header /Side Bow/Assembly

Right Side

Right Side, Spring-CatchLooking frominside the Jeep

Push


Page 20Section 14 Attach Header /Side Bow Assembly to #3 Bow

Step 1With the Header/Side Bow Assembly latched in place, pivot the #3 Bow forward, and slide the slotted portion of each pivot knuckle over the flange on the bottom of each #3 Bow corner plate, so that the hole in the flange and the hole in the pivot knuckle are aligned.

Step 2Fasten the pivot knuckle on the end of each back leg of the Header/Side Bow Assembly to the flange on the underside of each #3 Bow corner plate, using (1) Pivot Knuckle Screw per side.

Step 1 Step 2Header /Side Bow/Assembly

1 2


Hardware

Pivot Knuckle ScrewQty. 1 per sidePart # 308.65

Section 15 Drape Fabric over the top of the Jeep and Fold Front Portion of Top Back


Step 1Lift up the fabric and drape it back over the top of the Jeep, pulling it over the top of the extended #3 Bow and Stay Strap connect-ing to the #4 Bow.

Step 2Fold the top back from the front pivot point, resting the front portion of the top on the rear portion.

Step 1 Step 2Fabric

Section 16 Attach Foam Seal and Foam Tape on inside of Header


Step 1With the front portion of the top folded back, locate the (2) Foam Seals and the (2) Foam Tape strips. Remove protective liner from the back side of the Foam Seal and place the Foam Seal in the location shown in the diagram.

Remove protective liner from the back side of the Foam Tape Strip and place the Foam Tape Strip in the location shown in the diagram.

Repeat for the left side.

Step 1 Foam Seals and Foam Tape Strips


Hardware

Foam Tape StripsQty. 2Part # 417.43

Foam SealsQty. 1 per sideParts # 457.77(L)& #457.76(R)


Page 23Section 17 Attach Cable Spring to #3 Bow Corner Plate

Step 1

Step 2

Attach the free end of the Cable Spring to the bottom hole in the #3 Bow corner plate, just behind the Rear Door Rail.

Repeat on left side.

Crimp the end of the spring where it passes through the hole in the corner plate, to prevent it from coming loose.

Repeat on left side.

Step 3Fold the front portion of the top back toward the closed position, letting it stop in a partially open position.

Step 1 Step 2Cable Springs

Step 3


Page 24Section 18 Attach Bow Flaps to #4 Bow

Step 1From inside the Jeep, wrap the 4 fabric flaps at the rear of the top around the #4 Bow from underneath, and secure to the #4 Bow, using (4) #8x1/2” Pan Head Washer Screws.

Step 1 #4 Bow Flaps Hardware



Page 25Section 19 Attach Bow Flap to #3 Bow

Step 1From inside the Jeep, wrap the flap located above the #3 Bow over the front of the #3 Bow, and secure it, using (4) #8x1/2” Pan Head Washer Screws, in the pre-drilled holes in the front-facing side of the #3 Bow.

Step 1 #3 Bow Flap Hardware


Pre-Drilled Holes on front-facingside of #3 Bow

Section 20 Attach Bow Flap to #2 Bow


Step 1From inside the Jeep, wrap the flap located above the #2 Bow under the bottom of the #2 Bow, from front to back, and secure it, using (5) #8x1/2” Pan Head Washer Screws in the pre-drilled holes in the rear-facing side of the #2 Bow.

Step 1 #2 Bow Flap

Front

Hardware


Pre-Drilled Holes on rear-facingside of #2 Bow


Page 27Section 21 Close Front Windshield Header Latches

Step 1From inside the Jeep, locate the two Windshield Header Latches. To close the latch, pivot the latch handle to the completely open position to allow the hook to engage the windshield loop. Now pivot the hook forward to engage the windshield loop.

Step 2

Step 2

When the hook is engaged with the wind-shield loop, close the latch by pivoting it forward toward the windshield.

Step 1

12


Page 28Section 22 Install Rear Window

Step 1Locate the Rear Window, and orient it so that the zipper pull is at the bottom left corner.

Make sure that the two zipper pulls are next to each other at the bottom left corner of the Rear Window.

Step 2Zip the Rear Window into place by pulling the top zipper pull around the frame of the window, from the bottom left corner over to the bottom right corner.

Step 1 Step 2Rear Window

1

2

Section 23 Install Tailgate Bar


Step 1Locate the Tailgate Bar, and slide it onto the tubing attached to the bottom inside of the Rear Window.

Step 2The round channel on the side of the Tailgate Bar slides over the tubing.

Step 1 Step 2Rear Window

Tailgate BarQty. 1 Part #489.46

Hardware


Page 30Section 24 Snap Tailgate Bar Onto Tailgate Bar Mounts

Step 1Snap the front edge of the Tailgate Bar into the channel on the Tailgate Bar Mount.


Step 1 Tailgate Bar

Right Side


Page 31Section 25 Secure Rear Corners of Fabric to Jeep Belt Rail

Step 1Tuck the plastic tab at the bottom right corner of the Rear Window under the Jeep belt rail, by rolling it up underneath the belt rail.


Step 2Tuck the plastic tabs at the bottom right corner of the top under the Jeep belt rail, by rolling them up underneath the belt rail.


Step 1 Plastic Corner Tabs on Rear Window Step 2 Plastic Corner Tabs



Page 32Section 26 Install Side Windows

Step 1Locate the Right Side Window, and orient it so that the zipper pull is at the top right corner. Zip the window only 2” closed for now.


Step 2Tuck the plastic angle strip along the front edge of the Side Window into the vertical channel in the front of the Rear Door Rail. The plastic angle strip and attached fabric must be rolled into place in the channel.


Step 1 Step 2Side Windows

2”


Page 33Section 27 Install Side Windows (cont.)

Step 1

Step 2

Finish zipping the Right Side Window completely closed.

Repeat for the Left Side Window.

Tuck the plastic strip along the bottom edge of the Right Side Window under the Jeep belt rail, by rolling it up underneath the belt rail.

Repeat for the Left Side Window.

Step 1 Step 2Side Windows

When operating the vehicle without the Side Windows, remove the Rear Window for proper ventilation.


Page 34Section 28 Folding the Top Down

Remove the Side Windows, and roll up the Rear Window. To roll up the Rear Window, remove the Tailgate Bar, unzip the sides of the window up to the top, and roll the window up from the bottom, being careful not to wrinkle it. Secure the rolled up window in place with the elastic straps at the top.

Release the windshield latches. Fold the front header back, keeping the fabric folded neatly. Push down on the spring catch lever to release the side bows. Release the #3 and #4 Bows by pulling on the spring catch knobs.

Lift the fabric and bow assembly and swing it back to the rear of the Jeep, resting the entire assembly on the top edge of the Jeep belt rail. Wrap the fabric around the bows, and tuck the #3 and #4 Bows under the fabric. Tuck fabric in around the edges.

Step 1 Step 2

1

2

3

4




Care and Maintenance of your Bestop ProductYour Bestop product is made of the finest materials available. To keep it looking new and for the maximum possible wear, it will need periodic cleaning and maintenance.Fabric: The fabric should be washed often using soap, warm water and a soft bristle brush Rinse with clear water to remove all traces of soap. Bestop recommends using Bestop Cleaner (part no. 11201-00) and Bestop Protectant (part no. 11202-00) Bestop Cleaner and Bestop protectant are specially formulated to provide a total cleaning and protection system. Bestop Cleaner safely removes the toughest stains, will not harm vehicle finishes, is biodegradable and environmentally friendly. Bestop Protectant protects against fading, cracking and hardening, and repels dust, grease, dirt and mildew.

Windows: Keep windows clean to avoid scratching. DO NOT use a brush on the windows! Wash with a water-soaked cloth or spongeand a mild dishwashing detergent. Bestop recommends Bestop Vinyl Window Cleaner (part no. 11203-00), which safely cleans and protects vinyl windows and helps prevent UV damage. NEVER WIPE THE WINDOWS WHEN THEY ARE DRY.Be careful when cleaning snow or frost from the vinyl windows since they are easily scratched and may crack at low temperatures.DO NOT roll the sides or rear window in cold weather. The windows become stiff and will crack. Cracks caused by misuse in coldtemperatures are not covered under warranty. Zippers: Keeping zippers cleaned and lubricated with Bestop’s Zipper Cleaner (part no. 11206-00) will help prevent damage and keep thezippers in smooth working condition. If a zipper opens behind the slider, the slider may have been spread apart. This problem can usuallybe repaired by using an ordinary pair of pliers to bring the sides back into parallel. Return slider to the end of the zipper in the normal Openposition. Squeeze lightly at first and test the zipper. If the zipper continues to remain open squeeze more firmly with the pliers and try thezipper again. Repeat this procedure until the zipper operates correctly.

Water: Seeping through at the seams may be stopped by applying 3-M Scotchgard® on the inside of the seams. Rips in the fabric may berepaired with Bondex® iron on patches. Iron the patches to the Inside of the top, carefully following the Bondex® instructions.

Snaps: Keep snaps cleaned and lubricated with silicone to help prevent snaps from sticking to the studs. If a snap does become stuckto a stud, use a screwdriver and GENTLY pry apart to prevent permanent damage to the snap or the top fabric.

LIMITED WARRANTYWe warrant our product to be free from defects in material and workmanship, for the terms specified below, provided there has been normal use and proper maintenance. This warranty applies to the original purchaser only. All remedies under this warranty are limited to the repair or replacement of any item or items found by the factory to be defective within the time period specified. If you have a warranty claim, first you must call our factory at the number below for instructions. You must retain proof of purchase and submit a copy with any items returned for warranty work. Upon completion of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage to our products caused by accidents, fi re, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective parts not manufactured by us, is not covered under this warranty.

THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR REPLACE-A-TOP™, SAILCLOTH REPLACE-A-TOP™, SUPERTOP®, SUPERTOP® REPLACEMENT SKINS, SUNRIDER®, AND TIGERTOP®: TWO YEARS FROM DATE OF PURCHASE.THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR ALL OTHER “SOFT GOODS” MANUFACTURED BY OUR COMPANY (USING PRIMARILY VINYLS, PLASTICS , AND/OR FOAM): ONE YEAR FROM DATE OF PURCHASE.THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR ALL OTHER “HARD GOODS” MANUFACTURED BY OUR COMPANY (USING PRIMARILY METALS, PLASTICS , AND/OR FIBERGLASS): ONE YEAR FROM DATE OF PURCHASE.ANY IMPLIED W ARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAMEDURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or con sequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state.

For further information or request for warranty work, please contact:Bestop Inc., Customer ServiceToll-Free: (800) 845-3567Main: (303) 465-1755E-mail: [email protected]: www.Bestop.com

Damaged Slider - Jaws Spread Apart (sometimes broken)

Normal Slider - Jaws Parallel

P35F - 54723 - Rev. O 1114 Installation Instructions - Supertop NX © 2014 Bestop, Inc.



Pour de plus amples renseignements et demander une réparation, communiquer avec:Le service à la clientèle Bestop Inc.Sans frais : (800)845-3567Local: (303)465-1755Courriel: [email protected] Web: www.Bestop.com

Soin et entretien de votre produit BestopVotre produit Bestop est fabriqué des meilleurs matériaux disponibles. Il devra être nettoyé et entretenu régulièrement afin de maintenir son apparence neuve et pour une durée d’utilisation maximale.

Tissu: Le tissu doit être lavé régulièrement à l’aide de savon, d’eau chaude et d’une brosse à soies douces. Rincer à l’eau claire afi n d’éliminer toute trace de savon. Bestop recommande d’utiliser le nettoyant Bestop Cleaner (no de pièce 11201-00) et le protecteur Bestop Protectant (no de pièce 11202-00). Le nettoyant Bestop Cleaner et le protecteur Bestop Protectant sont spécialement formulés pourfournir un système de nettoyage et de protection complet. Le nettoyant Bestop Cleaner élimine de manière sécuritaire les taches les plus tenaces, n’endommagera pas les fi nis du véhicule, est biodégradable et respectueux de l’environnement. Le protecteur Bestop Protectant prévient la décoloration, la fi ssuration et le durcissement causés par les UV, et repousse la poussière, la graisse, la saleté et les moisissures.

Fermetures à glissière: Maintenir les fermetures à glissière propres et lubrifi ées à l’aide du nettoyant Zipper Cleaner (no de pièce 11206-00) de Bestop aidera à protéger des dommages et maintiendra les fermetures à glissière en bon état de fonctionnement. Si une fermeture à glissière ouvre derrière la glissière, la glissière peut avoir été forcée au point de s’ouvrir. Le problème peut habituellement être réparé en utilisant des pinces ordinaires pour remettre les côtés parallèles. Remettre la glissière au bout de la fermeture à glissière, dans la position Ouverte normale. Serrer légèrement au début et vérifi er le fonctionnement de la fermeture à glissière. Si la fermeture à glissière continue de rester ouverte, serrer plus fortement à l’aide des pinces et essayer la fermeture à glissière de nouveau. Répéter le processus jusqu’à ce que la fermeture à glissière fonctionne correctement.

Eau: Les in fi ltrations d’eau aux coutures peuvent être arrêtées par l’application de ScotchgardMD 3M sur l’intérieur des coutures. Les déchirures dans le tissu peuvent être réparées grâce aux pièces thermocollantes BondexMD. Fixer les pièces thermocollantes à l’aide d’un fer à repasser sur l’intérieur du toit, en suivant soigneusement les instructions de BondexMD.Boutons pression: Maintenir les boutons pression propres à l’aide de silicone pour empêcher les boutons pression de coller aux rivets. Si un bouton pression reste collé à un rivet, utiliser un tournevis et appliquer une FAIBLE PRESSION afi n d’éviter d’endommager le bouton pression ou le tissu du toit.

Glissière normale - Mâchoires parallèles

Glissière endommagée - Mâchoires écartées (parfois brisées)

GARANTIE LIMITÉENous garantissons que notre produit est exempt de défauts de matériaux et de fabrication, pour les modalités précisées ci-dessous, pourvu qu’il ait été utilisé de façon normale et entretenu de manière adéquate. Cette garantie s’applique à l’acheteur original seulement. Tous les recours sous cette garantie sont limités à la réparation ou au remplacement de tout article ou articles reconnus par l’usine comme étant défectueux pendant la période de temps spécifi ée. Si vous devez faire une réclamation, vous devez d’abord appeler notre usine au numéro ci-dessous pour obtenir des instructions. Vous devez conserver la preuve d’achat et en transmettre une copie avec tous les articles retournés pour réparation sous garantie. À la fi n des travaux de garantie, le cas échéant, nous vous retournerons l’article ou les articles réparés ou remplacés en port payé à l’avance. Les dommages à nos produits causés par les accidents, les incendies, le vandalisme, la négligence, une mauvaise utilisation, une mauvaise installation, les cas fortuits ou par des pièces défectueuses qui ne sont pas fabriqués par nous, ne sont pas couverts par cette garantie..LA PÉRIODE DE GARANTIE EST COMME SUIT POUR REPLACE-A-TOPMC, SAILCLOTH REPLACE-A-TOPMC, SUPERTOPMD, LES PEAUX DE RECHANGE SUPERTOPMD, SUNRIDERMD ET TIGERTOPMD : DEUX ANS À COMPTER DE LA DATE D’ACHAT.LA PÉRIODE DE GARANTIE EST COMME SUIT POUR TOUS LES AUTRES “BIENS DE CONSOMMATION NON DURABLES” FABRIQUÉS PAR NOTRE SOCIÉTÉ (EN UTILISANT PRINCIPALEMENT DES VINYLES, DES MATIÈRES PLASTIQUES ET/OU DE LA MOUSSE): UN AN À COMPTER DE LA DATE D’ACHAT.LA PÉRIODE DE GARANTIE EST COMME SUIT POUR TOUS LES AUTRES “BIENS DE CONSOMMATION DURABLES” FABRIQUÉS PAR NOTRE SOCIÉTÉ (EN UTILISANT PRINCIPALEMENT DES MÉTAUX, DES MATIÈRES PLASTIQUES ET/OU DE LA FIBRE DE VERRE): UN AN À COMPTER DE LA DATE D’ACHAT.TOUTE GARANTIE IMPLICITE DE QUALITÉ MARCHANDE ET/OU D’ADÉQUATION À UN USAGE PARTICULIER CRÉÉ PAR LES PRÉSENTES EST LIMITÉE AUX MÊMES CONDITIONS ET AU MÊME CHAMP D’APPLICATION QUE LA GARANTIE EXPRESSE ÉCRITE. NOTRE SOCIÉTÉ NE SERA PAS TENUE POUR RESPONSABLE POUR TOUT DOMMAGE ACCESSOIRE OU INDIRECTCertaines provinces et certains territoires n’autorisent pas les limitations sur la durée d’une garantie implicite, ou l’exclusion ou la limitation des dommages accessoires ou indirects, et il se pourrait donc que les limitations ou exclusions susmentionnées ne s’appliquent pas à vous. Cette garantie vous donne des droits légaux spécifi ques, et vous pouvez également avoir d’autres droits qui varient d’une province à l’autre et d’un territoire à l’autre.

P35S - 54723 - Rev. O 1114 Installation Instructions - Supertop NX © 2014 Bestop, Inc.



Para obtener más información o solicitar un trabajo de garantía, comuníquese con:Atención a clientes de Bestop IncNúmero para llamar sin costo: (800)845-3567 Conmutador: (303)465-1755 Courriel : [email protected] web: www.Bestop.com

Cuidado y mantenimiento de su producto Bestop Su producto Bestop está hecho con materiales de la más alta calidad. Para mantener su apariencia nueva y alargar su uso al máximo posible, necesitará limpieza y mantenimiento periódicos.

Tela: debe lavar la tela con frecuencia usando jabón, agua tibia y un cepillo de cerdas suaves. Enjuague con agua limpia para eliminar todos los residuos de jabón. Bestop recomienda utilizar el Limpiador Bestop (número de parte 11201-00) y el Protector Bestop (número de parte 11202-00). El limpiador y el protector Bestop están formulados especialmente para ofrecen un sistema de limpieza y protección total. El limpiador Bestop quita las manchas más difíciles, no daña los acabados del vehículo, es biodegradable y no daña el medio ambiente. El protector Bestop protege contra la decoloración que causan los rayos UV y contra elagrietamiento y endurecimiento; además, repele el polvo, grasa, suciedad y moho.

Cremalleras: conserve las cremalleras limpias y lubricadas con el limpiador de cremalleras Bestop (número de parte 11206-00), que ayuda a prevenir daños y mantiene las cremalleras en óptimas condiciones de funcionamiento. Si la cremallera se abre detrás de la corredera, es posible que las mordazas de la corredera se hayan separado. Por lo general, este problema se repara fácilmente con unas pinzas comunespara volver a poner los lados en paralelo. Regrese la corredera al extremo de la cremallera en la posición abierta normal. Apriete un poco al principio y pruebe la cremallera. Si la cremallera sigue abierta, apriete con mayor fi rmeza con las pinzas y vuelva a probar la cremallera. Repita este procedimiento hasta que la cremallera funcione correctamente.

Agua: para eliminar la fi ltración de agua a través de las costuras, aplique cinta Scotchgard® de 3-M en la parte interior de las costuras. Los desgarres de la tela pueden repararse con parches Bondex® para aplicar con plancha. Planche los parches en el interior del toldo, siguiendo con cuidado las instrucciones de Bondex®.

Broches: conserve los broches limpios y lubricados con silicona para evitar que se peguen a los corchetes de encaje. Si se quedan pegados a un corchete, use un destornillador y CON CUIDADO separe las dos piezas para evitar daño permanente al broche o a la tela del toldo.

Corredera normal - Mordazas paralelas

Corredera dañada - Mordazas abiertas (a veces, rotas)

GARANTÍA LIMITADA Garantizamos que nuestro producto estará exento de defectos en materiales y mano de obra durante los plazos que se indican a continuación, siempre que se les dé el uso normal y el mantenimiento adecuado. Esta garantía aplica únicamente al comprador original. Todos los recursos previstos en esta garantía se limitan a la reparación o sustitución de cualquier artículo o artículos que la fábrica determine que efectivamente presentan defectos dentro del período especifi cado. Si desea presentar una reclamación de garantía, primero debe llamar a nuestra fábrica al número que se indica a continuación para recibir instrucciones. Debe conservar el comprobante de compra y enviar una copia junto con los artículos devueltos para la reparación de garantía. Al término del trabajo de garantía, si lo hubo, devolveremos el o los artículos reparados o sustituidos a su domicilio por fl ete prepagado por usted. Esta garantía no cubre los daños que sufran nuestros productos a causa de accidentes, incendio, vandalismo, negligencia, errores de instalación, mal uso, causas de fuerza mayor o provocados por partes defectuosas que no fabricamos nosotros.EL PERÍODO DE GARANTÍA DE REPLACE-A-TOP™, SAILCLOTH REPLACE-A-TOP™, SUPERTOP®, SUPERTOP® REPLACEMENT SKINS, SUNRIDER® Y TIGERTOP® ES EL SIGUIENTE: DOS AÑOS A PARTIR DE LA FECHA DE COMPRA.EL PERÍODO DE GARANTÍA PARA TODOS LOS DEMÁS “PRODUCTOS BLANDOS” FABRICADOS POR NUESTRA EMPRESA (EN CUYA FABRICACIÓN SE UTILIZARON SOBRE TODO VINILOS, PLÁSTICOS O ESPUMA) ES EL SIGUIENTE: UN AÑO A PARTIR DE LA FECHA DE COMPRA.EL PERÍODO DE GARANTÍA PARA TODOS LOS DEMÁS “PRODUCTOS RÍGIDOS” FABRICADOS POR NUESTRA EMPRESA (EN CUYA FABRICACIÓN SE UTILIZARON SOBRE TODO METALES, PLÁSTICOS O FIBRA DE VIDRIO) ES EL SIGUIENTE: UN AÑO A PARTIR DE LA FECHA DE COMPRA.TODAS LAS GARANTÍAS IMPLÍCITAS DE COMERCIABILIDAD O IDONEIDAD PARA UN FIN ESPECÍFICO QUE AQUÍ SE CREAN SE LIMITAN EXACTAMENTE A LA MISMA DURACIÓN Y ALCANCE QUE LA GARANTÍA EXPLÍCITA ESCRITA. NUESTRA COMPAÑÍA NO SERÁ RESPONSABLE POR NINGÚN DAÑO INCIDENTAL O EMERGENTE.En algunos estados no se permiten las limitaciones respecto a la duración de las garantías implícitas ni la exclusión o limitación de los daños incidentales o emergentes, por lo que es posible que las anteriores limitaciones o exclusiones no apliquen a usted. Esta garantía le confi ere derechos legales específi cos, y también puede tener otros derechos, los cuales varían de un estado a otro.

tools installation time support · for easier installation, the top should be installed at a...

Documents