triboard manual tc3x4l v1 - infineon technologies

User Manual Please read the Important Notice and Warnings at the end of this document V1.2www.infineon.com TriBoard TC3X4L TH V1.0 and TriBoard TC3X4L V1.0 2019-09

TriBoard TC3X4L

TriBoard Manual TC3X4LHardware: Tr iBoard TC3X4L TH V1.0 and TriBoard TC3X4L V1.0

About this document

Scope and purpose

The User Manual provide information about using, configuration and connecting the TriBoard with InfineonAURIX™ TC3X4 LQFP device. The manual provide information for different hardware types. There exist differenthardware with Through Hole socket (TriBoard TC3X4L TH) and soldered devices (TriBoard TC3X4L). Theschematic is identically for the all boards if not other mentioned in chapter schematic. The placing on the boardsis the same, all components are on the same location.

Intended audience

Design, verfication, test and software engineers will use this document to get an understanding of thefunctionality and connections of the TriBoard.

User Manual TOC-2 V1.2 TriBoard TC3X4L TH V1.0 and TriBoard TC3X4L V1.0 2019-09

TriBoard Manual TC3X4LHardware: TriBoard TC3X4L TH V1.0 and TriBoard TC3X4L V1.0

Table of Contents

About this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-1

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TOC-2

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12.1 Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22.3 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

3 TriBoard Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13.1 Soldered board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13.2 Socketed board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13.2.1 Usable devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13.2.2 Restricted usable devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13.3 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13.3.1 Failsafe handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23.4 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23.5 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33.6 USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33.6.1 Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33.6.2 miniWiggler JDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43.7 FlexRay™ (E-RAY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43.8 Serial Eeprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43.9 MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43.10 LIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53.11 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53.12 HSCT (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63.12.1 High speed with HSCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63.13 ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-73.14 Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-83.15 Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-83.16 Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-83.17 Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-93.17.1 OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-93.17.2 DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-93.17.3 DAP_SCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-93.17.4 High speed with DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-93.17.5 ETK connector (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-103.17.6 EmW Power (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

4 TriBoard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14.1 HW Boot Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14.1.1 Default Pad State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14.1.2 Bootmode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14.2 Assembly Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24.2.1 General optional resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24.2.2 Resistors for peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

5 Signal (on board used) Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15.1 Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Table of Contents

User Manual TOC-3 V1.2 TriBoard TC3X4L TH V1.0 and TriBoard TC3X4L V1.0 2019-09


Table of Contents

5.2 Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15.3 Config Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25.4 Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25.5 Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25.6 Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

6 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16.1 On Board only used signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16.2 TC3X4 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26.3 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-46.4 USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-46.5 FlexRay™ (ERAY) connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-46.6 CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-46.7 LIN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-56.8 HSCT connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-56.9 Ethernet connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-56.10 OCDS1 connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-66.11 DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-66.12 ETK connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-76.13 Ethernet miniWiggler power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

7 Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17.1 Known problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17.1.1 Known problems on TriBoard TC3X4L TH V1.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17.1.2 Known problems on TriBoard TC3X4L V1.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17.2 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17.3 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-97.4 Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11

User Manual 1-1 V1.2 TriBoard TC3X4L TH V1.0 and TriBoard TC3X4L V1.0 2019-09


Introduction

1 IntroductionWe congratulate you on your purchase of the TriCore Evaluation Board. This kit is a versatile tool, providing quickaccess to the capabilities of TriCore's powerful architecture.Applications can be developed easily. The Evaluation Board is equipped with a variety of memories andperipherals for connection to the environment. There is also an interface for the On Chip Debugging Features(OCDS1 and DAP). The Evaluation Board allows easily the development of TriCore applications with the corresponding tools.Subsequently, the applications can be downloaded and can be tested with the powerful debugger software.This TriBoard Hardware Manual familiarizes you with the TriCore Evaluation Board and guides you through theinitial configuration of the TriBoard. For detailed technical information about the TC3X4 LQFP (e.g. TC374, TC364) please refer to the User Manual ofthe used device.



Features

2 Features

2.1 Summary of Features– Infineon’s TC3X4 (TC374, TC364) AURIX™ 2G Controller in LQFP-144 Package– FlexRay™ 1) Transceivers– High Speed CAN Transceivers (CAN-FD capable)– USB to UART bridge– Ethernet PHY– Serial Eeprom– LIN Transceiver– Crystal 20MHz (default) or External Clock– USB miniWiggler JDS for easy debugging– 8 Low Power Status LEDs– 8-DIP switches for configuration– access to all pins of controller– 100mm x 160mm (EURO-Board)

ConnectorsThe TC3X4L TriBoard offers a wide variety of connectors:

– Standard power connector– Micro USB connector for ASC Interface (ASC0) and miniWiggler– RJ45 connector for Ethernet– 16-pin header for JTAG interface (OCDS)– 2 x 10-pin header for DAP and DAP_SCR– 10pin (2x5) Header for LIN Transceiver (LIN)– 2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1)– 2 x 10pin (2x5) Header for FlexRay™ (ERAY-A and ERAY-B)– four 80-pin connectors (male) + four 80-pin connectors (female) with all I/O signals– optional ETK connector– optional 6pin (IEEE1394) Socket for HSCT

Components– Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV– Three LEDs to validate power supply (5Volt / 3,3 Volt / 1,25 Volt)– LED indicating safe state signal 2 from TLF35584– LED indicating /HDRST (ESR0) active state– LED indicating activ miniWiggler JDS– LED switched via DAS software– 2 x Infineon’s FlexRay™ Transceiver TLE9221SX– 2 x Infineon’s High Speed CAN-Transceiver TLE9251VSJ– Infineon’s LIN-Transceiver TLE 7259-3GE– USB to UART bridge FT2232HL (FTDI)– Single-Chip/Port 10/100M Ethernet PHYCEIVER with Auto MDX RTL8201FI-VC-CG (Realtek)– 8 general purpose LEDs– 2K I2C Serial Eeprom with EUI-48™ 2) Node Identity (MICROCHIP)

1) FlexRay™ is a trademark of FlexRay Consortium.



Features

– Reset switch– Enable switch– Generic switch– 4-pin Dip switch

Zero Ohm BridgesZero Ohm resistors give the flexibility to configure the systems functionality.

2.2 Block Diagram

Figure 2-1 TriBoard Block Schematic

2) EUI-48™ is trademarked by IEEE

MicroUSB miniWiggler

OCDS1

USB

XTAL

FlexRay™ Transceiver

Transceiver

TxCAN0

TxCAN1

RxCAN0

RxCAN1

TC3X4(e.g.

TC374, TC364)TriCore

CPU

PLLCAN0

CAN1

ER

AY

BE

RAY

A

TX0

RX0

8 LED’s (P33.4 up to P33.7,

P20.11 up to P20.14)Serial EEPROM with EUI-48™

RMII PHYTwisted Pair

RJ45

LIN LIN

Transceiver

TX1

RX1

HSC

Top

tiona

lHSCT - TX/RX

I²C

WAKEUP

QSPI2

Multi Voltage Safety Micro Processor Supply

TLF35584QV

ENA



Features

2.3 Placement

Figure 2-2 TriBoard TC3X4L (TH) V1.0 Placement

U201

X404

S502

X306U307

Y301

X604

X402

S201

X201

X305

X304

X303

C303

D401

BU401

D402

U401

Y401

Y201

T301

T302

X301

X302

X602X603

X601

D302 D303 D304 D305 D306 D307 D308 D309

D505

D506

D507D504

X401

X501

S501

U502

D508

U501

L502

L501

C502

C501

R501

S202

X502

X406

DAP



TriBoard Information

3 TriBoard Information

3.1 Soldered boardTriBoard TC3X4L V1.0 is the soldered board and will be available only with usable devices. Please see also chapterUsable devices.

3.2 Socketed boardTriBoard TC3X4L TH V1.0 is the socketed board.

3.2.1 Usable devices

Note: Note: Please check always the latest manual for complete list of usable/tested devices.

The board can be used with the following devices:• TC374• TC364DP-64F300W

Note: For TC364: AN42 is connected directly to ground and AN43 is connected to VDDM via R223. Additional there is a capacitor (CB206) between AN43 and AN42.

3.2.2 Restricted usable devices• None

3.3 Power SupplyAll needed voltages are generated via Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV and viathe microcontroller itself (+1,25V).The supply device is available as two different devices:TLF35584QVVS1 -> +5V standby voltage, +5V TriCore supply (V_UC)TLF35584QVVS2 -> +3,3V standby voltage, +3,3V TriCore supply (V_UC)Dependent of the assembled device the board works with 5V or 3,3V IO.The TLF35584QV provide the following voltages:+3,3V or +5V for standby (connected to VEVRSB)+3,3V or +5V for TriCore (connected to VEXT)+5V communcation supply (used by CAN and FlexRay™ transceivers)+5V voltage reference (connected to VDDM and VAREFx)+3,3V via LDO directly from pre regulator (used by Ethernet PHY)Applying a stable supply voltage causes the power on reset after a short period. The three LED's (V_UC, +3.3V,+1V25) indicate the status of the on board generated voltages.A manual power on reset is executed by pressing the reset button.The Board has to be connected to a +3,5V to +40V DC power supply.The power consumption is not specified yet but a supply with 12V and 500mA is recommended. The pinout forthe supply connector is shown in Figure 6-3. There can be used any standard power pack with a connector wherethe positive line is surrounded by the ground line.




3.3.1 Failsafe handlingIn case that the device don’t contains a program which disable or service the window watchdog and error pinmonitor of the TLF35584 then the TLF35584 is going to a FAILSAFE state where all supplies are switched off. Thisstate can be left via reconnect the power plug or via the ENA button (S502). In this case you must connect adebugger which is able to disable the window watchdog and error pin monitor to reprogram the microcontroller.In the default state of the board the switching to FAILSAFE state is switched off via resistor R508. If you will use/evaluate all safety features of the TLF35584 make sure that R509 is assembled and R508 is notassembled. Make sure that you have a proper initialization of TLF35584 in your softare.Resistor R508 and R509 are red marked in the following Figure 3-1:

Figure 3-1 Resistors for TLF35584 Safety feature handling with switch on

3.4 LEDsThere are 15 LEDs on board:

– D302 up to D305 (blue) -> toogle LEDs connected to P33.4 ... P33.7– D306 up to D309 (blue) -> toogle LEDs connected to P20.11 ... P20.14– D504 RST (red) -> RESET LED indicate the reset state of the board (/ESR0)– D505 +1V25 (green) -> +1V25 power supply indication– D506 +3V3 (green) -> +3,3V power supply indication– D507 V_UC (green) -> +5V/+3,3V power supply indication– D508 SS2 (green) -> safe state signal 2 indication– D402 ACT (green) -> on board miniWiggler JDS is ACTIV– D401 RUN (blue) -> Debug RUN mode (switched by DAS Server)

U201

R395

X404

R212

S502

R222 CB205

R379

R372

C305

C310

X306

CB313

CB314

CB315

C311

U307

Y301

X604R249

R246R245

R244

X402

S201

R377

R204R205

R215R214

X201

X305

X304

X303

R240

R236

R234

R232

R230

R223

R361

R359

R211

D301

CB206

C303

U408U407U406

R451

R455

R456

R454

R446

R444

CB419

CB418

CB417

CB416

CB415

CB414

D401

R430R429

R423

CB405

C402

R411

BU401

L401

D402

R401

CB401

U404

U401

Y401

CB408

R403

R402

CB402

R344

R524

R424

R425

R426

R427

R428 CB520

R201

CB204

R203

R202

C201

C202

R206

R207 Y201

R337

R357

R324

R399

R391 R392 R393 R394 R396 R397

CB309

R532

C301

C302

R439

R531

R335

R336

R355

R356

U305

T301

T302

X301

X302

X602X603

X601

D302

D303

D304

D305

D306

D307

D308

D309

D505

D506

D507D504

X401

X501

S501

R354

C519

R452

CB203

R213R216

R398

U502C505

D508

U501

L502

L501 CB501

C502

C507

C509

C508

C501

C503

C504

R501

R507

R508

R509

CB502

R231

R233

R235

R237

R241

R255

R256

R390

R375

R376

R348

R349

R525

S202

X502

R346

R 347

R457

X406

C522

CB316

CB317

U308

R248




3.5 ClockOn the board is a fixed crystal with 20MHz assembled. You can change this by replacing Y101 (soldered).

3.6 USB ConnectorThe USB connector is used for connection to a PC. Via the USB it is possible to power the board, using the ASCLIN0as serial connection via USB and Debugging via DAS. For the pinout of USB socket see Figure 6-4.NOTE: Before connecting the board to the PC, make sure that the actual DAS software is installed on the PC. Foractual DAS software please contact your local FAE.The software can also be found on:

DAS website3.6.1 Serial Connection to PCAfter the first connection of USB to a PC the needed driver will be installed automatically. During this there willbe created a new COM port on PC. This COM port can be used to communicate with the board via ASCLIN0 of thedevice. Per default the ASCLIN0 is used on P14.0 and P14.1 (e.g. Generic Bootstrap Loader) . In case you will usethe Generic Bootstrap Loader via CAN or ASCLIN0 via P15.2 and P15.3 you must:

– remove R436 and R437 (this disconnect the serial connection from P14.0 and P14.1)– remove R301 and R302 (this disconnect the CAN0 transceiver from P20.7 and P20.8)– assemble R438 and R440 with 0R resistor (size 0603) to connect P15.2 and P15.3 to serial connection– assemble R303 and R304 with 0R resistor (size 0603) to connect P14.0 and P14.1 to CAN0 transceiver

The mentioned resistors are red marked in Figure 3-2.

Figure 3-2 Resistors for ASC connection (ASC0)

X703

CB511

R388

R380

R378 Q301

R368

R371

R382

R419

R440

R369

R367

C320

C317

C316C315C314

C313

C312

Q403

R389

R383

R385

R370 CB311

CB312

C208

C207

C205

C204C203

R433

R523

R431

R381

R314

R252R250

R251R253

R254

CB202R208

R408

U306

R521

R238

R365R364

R363

R362

R360 CB310

C304

R449

R448R447

R445

R443

R413

U405

L402

CB4

13C403

D403

R404C401

R450

R442

R441

CB412

CB411

CB410

C405C404

R422

R421

U403

Q402

Q401

R412

C406

R420

R414

R418

R417 R416

R415

R410

R 409CB407

CB403

R407

U402

R406 R405

CB406

CB404

R305

R306

R308 R309

R315

R316

R318

R319

R522

R301

R311

R341

R340

R321

R322

R220R221

R533

R323

R343

CB301

CB302

CB512

CB513

CB515

CB5

16

CB517

CB518

CB5

19

R537

R307

R317

R538

R534

R513

R535

R536

C515

R511

R512

R510

Q502

Q504

Q503

X702

X704X701

U301

U302

R302

R342

CB303

CB304

CB305

CB306

CB307

CB308

R303

R304

R338

R330

R331

R358

R350

R351

U303

U304

R332

R334

R333

R352

R353

R320

CB201R209

CB510

R520

D503

R505

R504

C510

R502

R506

Q505 Q501

D501

C512

C511

D502

R503

R239

R312

R436

R437

R438

R313

R373

R374

Q506

L503

C520

C521

C506

CB506 U503

CB409R386

C306

http://www.infineon.com/das




3.6.2 miniWiggler JDSThe miniWiggler JDS is a low cost debug tool which allows you access to the JTAG of the device. Make sure thatyou have the latest DAS release. Debugging is possible via the DAS Server ‘UDAS‘. Please contact your prefereddebug vendor for support of DAS.If you have connected the board to the PC and there runs the DAS server, then a working connection is visible viathe green ACTIV LED.The status RUN LED is switched on/off through the DAS Server, depending on the used debugger (client).IMPORTANT: Make sure that there is no or a tristated connection on X401 (OCDS1) and X402 (DAP) if theACTIV LED is on.Per default the miniWiggler is connected to the DAP. If resistors R214, R215 and R216 assembled (default) thenthe standard DAP is connected to miniWiggler. If all this resistors are not assembled then the miniWiggler can’tbe used. In this case only the DAP connectors X402 and X406 can be used. See Figure 3-7.

3.7 FlexRay™ (E-RAY)The board has 2 IDC10 plugs for FlexRay™ Communication (channel A and B) with up to 10 Mbit/s. For the pinoutof the plugs see Figure 6-5. You can use a IDC female connector with crimpconnector, flat cable and SUB-D 9 plugwith crimpconnector to have a 1:1 adapter to SUB-D 9.The transceiver are connected to the TriCore device via zero ohm resistors (R320 up to R324 and R340 up to R344)which must be removed to use the ports outside.ERAY-A can be connected to P02.0, P02.1 and P02.4. Transceiver for channel A can be enabled/disabled via P10.1.The error state of transceiver channel A can be read out via P10.2.ERAY-B is connected to P02.2, P02.3 and P02.5. Transceiver for channel B can be enabled/disabled via P20.10. Theerror state of transceiver channel A can be read out via P20.9.For more information look in the user manual for TC3X4 LQFP.

3.8 Serial EepromThe I2C via P15.4 and P15.5 of the TC3X4 is connected to a serial EEPROM with a size of 2KBit (2 x 128 x 8). The slaveaddress of this EEPROM is 0x50. The upper half of the array (80h-FFh) is permanently write-protected. Writeoperations to this address range are inhibited. Read operations are not affected. This upper half contains a pre-programmed EUI-48™ node address which can be used as MAC ID for Ethernet. The other 128 bytes are writableby customer.To disconnect (disable) the EEPROM remove resistor R348 and R349.

3.9 MultiCANOn the board are two CAN transceiver connected to the CAN0 and CAN1 of TC3X4 LQFP. The transceivers areconnected to two IDC10 plug. For the pinout of IDC10 plug see Figure 6-6. You can use a IDC female connector withcrimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.The transceiver are connected to the TriCore device via zero ohm resistors (R301 up to R304 and R311 up to R314)which must be removed to use the ports outside.CAN0 can be used via P20.7 and P20.8 (CAN0 node 0, default) or P14.0 and P14.1 (CAN0 node 1). CAN1 can be usedvia P13.0 and P13.1 (CAN1 node 0, default) or P00.0 and P00.1 (CAN1 node 0).




3.10 LINOn the board is one LIN transceiver connected to the ASCLIN1 on TC3X4 LQFP (P15.0 and P15.1). The transceiverare connected to one IDC10 plug. For the pinout of IDC10 plug see Figure 6-7. You can use a IDC female connectorwith crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.To disconnect the LIN remove resistor R364 and R365. The LIN can be used in master and in slave mode. For the master mode there is per default a pull-up of 1K (R360)and a capacitor of 1nF (C304) on the BUS assembled. For using the LIN in slave mode the pull-up resistor R360must be removed and maybe the capacitor changed to a smaller value (e.g. 220pF).The mentioned resistor and capacitor are red marked in Figure 3-3

Figure 3-3 Components for LIN Master Mode

3.11 EthernetThe TriBoard provide a RJ45 connector (X306) for twisted pair ethernet connections.The TriBoard use a RealtekSingle-Chip/Port 10/100M Ethernet PHYCEIVER with Auto MDX RTL8201FI-VC-CG as physical interface device. Formore information about the ethernet modul see TC3X4 User’s Manual, about the PHY see the RTL8201FIdatasheet. For the pinout of RJ45 see Figure 6-9.The PHY is connected to the TriCore device via resistors and resistor arrays (R368 up to R374) which must beremoved to use the ports outside.For the connection between TriCore and PHY is used RMII.For MD connection there is used P00.0 and P02.8. To use this communication way please make sure that R376 isnot assembled (default). For R376 position please see also Figure 4-4.

Note: Please note that the RGMII interface can’t be used of limited pin availability. Therefore Gigabit is not usable with this board only 10M and 100M.

X703

CB511

R388

R380

R378 Q301

R368

R371

R382

R419

R440

R369

R367

C320

C317

C316C315C314

C313

C312

Q403

R389

R383

R385

R370 CB311

CB312

C208

C207

C205

C204C203

R433

R523

R431

R381

R314

R252R250

R251R253

R254

CB202R208

R408

U306

R521

R238

R365R364

R363

R362

R360 CB310

C304

R449

R448R447

R445

R443

R413

U405

L402

CB4

13C403

D403

R404C401

R450

R442

R441

CB412

CB411

CB410

C405C404

R422

R421

U403

Q402

Q401

R412

C406

R420

R414

R418

R417 R416

R415

R410

R 409CB407

CB403

R407

U402

R406 R405

CB406

CB404

R305

R306

R308 R309

R315

R316

R318

R319

R522

R301

R311

R341

R340

R321

R322

R220R221

R533

R323

R343

CB301

CB302

CB512

CB513

CB515

CB5

16

CB517

CB518

CB5

19

R537

R307

R317

R538

R534

R513

R535

R536

C515

R511

R512

R510

Q502

Q504

Q503

X702

X704X701

U301

U302

R302

R342

CB303

CB304

CB305

CB306

CB307

CB308

R303

R304

R338

R330

R331

R358

R350

R351

U303

U304

R332

R334

R333

R352

R353

R320

CB201R209

CB510

R520

D503

R505

R504

C510

R502

R506

Q505 Q501

D501

C512

C511

D502

R503

R239

R312

R436

R437

R438

R313

R373

R374

Q506

L503

C520

C521

C506

CB506 U503

CB409R386

C306




3.12 HSCT (optional)The TriBoard provide a footprint of IEEE 1394 socket (X201) for connection to other TC3XX via HSCT.

Note: Don’t use X201 for connection to any IEEE 1394 device, this can destroy the board and/or the connected device.

For connect two TriBoards you need to assemble this socket (Lumberg 2415 01) on each board and connect theboards with a standard 6 pin IEEE 1394 cable. For the pinout of socket see Figure 6-8.

3.12.1 High speed with HSCTFor use the HSCT connection between two board you need to remove 5 resistors to have a very short connectionbetween device and connector. On the TC3X4L Triboard this 5 resistors are R250, R251, R252, R253 and R254 (redmarked in Figure 3-4). This resistors needs to be removed.mportant: When the resistors are removed then the port signals P20.0, P21.2, P21.3, P21.4 and P21.5 are nolonger available on the 80 pin samtec connectors.

Figure 3-4 Resistors for high speed HSCT

X703

CB511

R388

R380

R378 Q301

R368

R371

R382

R419

R440

R369

R367

C320C317

C316C315C314

C313

C312

Q403

R389

R383

R385

R370 CB311

CB312

C208

C207

C205

C204C203

R433

R523

R431

R381

R314

R252R250

R251R253

R254

CB202R208

R408

U306

R521

R238

R365R364

R363

R362

R360 CB310

C304

R449

R448R447

R445

R443

R413

U405

L402

CB4

13C403

D403

R404C401

R450

R442

R441

CB412

CB411

CB410

C405C404

R422

R421

U403

Q402

Q401

R412

C406

R420

R414

R418

R417 R416

R415

R410

R 409CB407

CB403

R407

U402

R406 R405

CB406

CB404

R305

R306

R308 R309

R315

R316

R318

R319

R522

R301

R311

R341

R340

R321

R322

R220R221

R533

R323

R343

CB301

CB302

CB512

CB513

CB515

CB5

16

CB517

CB518

CB5

19

R537

R307

R317

R538

R534

R513

R535

R536

C515

R511

R512

R510

Q502

Q504

Q503

X702

X704X701

U301

U302

R302

R342

CB303

CB304

CB305

CB306

CB307

CB308

R303

R304

R338

R330

R331

R358

R350

R351

U303

U304

R332

R334

R333

R352

R353

R320

CB201R209

CB510

R520

D503

R505

R504

C510

R502

R506

Q505 Q501

D501

C512

C511

D502

R503

R239

R312

R436

R437

R438

R313

R373

R374

Q506

L503

C520

C521

C506

CB506 U503

CB409R386

C306




3.13 ADCOn this boards are 5 ADC channels prepared with a low pass filter. On pin AN7, AN20, AN21, AN44 and AN45 isassembled a capacitor of 47nF and a serial resistor of 4,7K. The filter components are red marked in the followingfigures (Figure 3-5 and Figure 3-6).

Figure 3-5 Filter components of ADC channels on Top Side

U201

R395

X404

R212

S502

R222 CB205

R379

R372

C305

C310

X306

CB313

CB314

CB315

C311

U307

Y301

X604

R249

R246R245

R244

X402

S201

R377

R204R205

R215R214

X201

X305

X304

X303

R240

R236

R234

R232

R230

R223

R361

R359

R211

D301

CB206

C303

U408U407U406

R451

R455

R456

R454

R446

R444

CB419

CB418

CB417

CB416

CB415

CB414

D401

R430R429

R423

CB405

C402

R411

BU401

L401

D402

R401

CB401

U404

U401

Y401

CB408

R403

R402

CB402

R344

R524

R424

R425

R426

R427

R428 CB520

R201

CB204

R203

R202

C201

C202

R206R207 Y201

R337

R357

R324

R399

R391 R392 R393 R394 R396 R397

CB309

R532

C301

C302

R439

R531

R335

R336

R355

R356

U305

T301

T302

X301

X302

X602X603

X601D302

D303

D304

D305

D306

D307

D308

D309

D505

D506

D507D504

X401

X501

S501

R354

C519

R452

CB203

R213R216

R398

U502C505

D508

U501

L502

L501 CB501

C502

C507

C509

C508

C501

C503

C504

R501

R507

R508

R509

CB502

R231

R233

R235

R237

R241

R255

R256

R390

R375

R376

R348

R349

R525

S202

X502

R346

R 347

R457

X406

C522

CB316

CB317

U308R248




Figure 3-6 Filter components of ADC channels on Bottom Side

3.14 Other peripheralsFor all other peripherals there are no special plugs on the board. The peripheral signals are available on thedifferent connectors. See “Connector Pin Assignment” on Page 6-1.

3.15 Toggle LED’sThe status LED’s are low active and can be controlled by Software.Port 20 pin 11 up to pin 14 are connected to single LED’s (D306... D309) and powered by the normalmicrocontroller voltage.Port 33 pin 4 up to pin 7 are connected to single LED’s (D302... D305) and powered by the standby voltage. Thismeans that this LED’s can be are activ also when the board is in standby mode and only the standby voltageavailable (port 33 is powered by VEVRSB pin which is connected to standby supply of TLF35584). In this case theport pins are controlled by the standby controller if available.

3.16 ButtonsOn the board are three buttons.The reset button (S501) will apply a warm power on reset to the device.The ENA button (S502) will be used to enable/wakeup the TLF35584.The P33.11 button (S202) can be used by software as input. Also can this button used by the standby controllerto react on an event when only standby supply is available (e.g. wakeup the TLF35584 via P33.10).

X703

CB511

R388

R380

R378 Q301

R368

R371

R382

R419

R440

R369

R367

C320

C317

C316C315C314

C313

C312

Q403

R389

R383

R385

R370 CB311

CB312

C208

C207

C205

C204C203

R433

R523

R431

R381

R314

R252R250

R251R253

R254

CB202R208

R408

U306

R521

R238

R365R364

R363

R362

R360 CB310

C304

R449

R448R447

R445

R443

R413

U405

L402

CB4

13C403

D403

R404C401

R450

R442

R441

CB412

CB411

CB410

C405C404

R422

R421

U403

Q402

Q401

R412

C406

R420

R414

R418

R417 R416

R415

R410

R 409CB407

CB403

R407

U402

R406 R405

CB406

CB404

R305

R306

R308 R309

R315

R316

R318

R319

R522

R301

R311

R341

R340

R321

R322

R220R221

R533

R323

R343

CB301

CB302

CB512

CB513

CB515

CB5

16

CB517

CB518

CB5

19

R537

R307

R317

R538

R534

R513

R535

R536

C515

R511

R512

R510

Q502

Q504

Q503

X702

X704X701

U301

U302

R302

R342

CB303

CB304

CB305

CB306

CB307

CB308

R303

R304

R338

R330

R331

R358

R350

R351

U303

U304

R332

R334

R333

R352

R353

R320

CB201R209

CB510

R520

D503

R505

R504

C510

R502

R506

Q505 Q501

D501

C512

C511

D502

R503

R239

R312

R436

R437

R438

R313

R373

R374

Q506

L503

C520

C521

C506

CB506 U503

CB409R386

C306




3.17 Debug System

3.17.1 OCDS1The OCDS1 signals are connected to the IDC16 plug (X401). They work with the port supply of Microcontroller (+5Vdefault or +3,3V). For pinout of the connector see Figure 6-10. You can connect any debugger to this connector. The signals /BRKIN and /BRKOUT are not connected per default. If you need this signals in the connector thenassemble R424 and R425 or R426 with a 0R resistor.If you connect a debug hardware make sure that the miniWiggler JDS (see “miniWiggler JDS” on Page 3-4) is notactiv (ACTIV LED is off) and on the DAP connector (X402) is no hardware connected or the hardware is tristated. If the ACTIV LED is on, then stop the active DAS Server ’UDAS’ and/or remove the USB connection to the PC.If R214 up to R216 not assembled then the connector is not usable.

3.17.2 DAPThe board comes with a DAP connector (X402). For pinout of this connector see Figure 6-11. You can connect aDAP hardware here. If you use this connector make sure that the miniWiggler JDS is not activ (ACTIV LED is off)and a connected OCDS1 hardware is disconnected or tristated.

3.17.3 DAP_SCRAdditional DAP connector (X406) is connected to DAP_SCR. This DAP can be used as private DAP connection tothe standby controller. For pinout of this connector see Figure 6-15. You can connect a DAP hardware here. ThisDAP use P33.6 and P33.7 which are connected to LED on the board. Maybe it is necessary to remove R393 andR394 if the speed of the connection is not fast enough.

3.17.4 High speed with DAPFor use the DAP connection with 160 MHz you need to remove 3 resistors to have a very short connection betweendevice and connector. On the TC3X4L Triboard this 3 resistors are R214, R215 and R216 for DAP (red marked inFigure 3-7). This resistors needs to be removed. Important: When the resistors are removed then only the DAP connector on the board can be used. The on boardwiggler and the OCDS1 connector couldn’t be use (are disconnected) in this case, also the DAP/JTAG part of theETK connector couldn’t be used.All resistors are red marked in the following figure:




Figure 3-7 Location of DAP resistors on Top Side

3.17.5 ETK connector (optional)The TriBoard provide a 10 pin samtec connector (X404) for connecting to an ETK. This connector should beassembled by your self if needed.For the pinout of connector see Figure 6-12.The needed Samtec connector is: TFM-105-02-A.

3.17.6 EmW Power (optional)The TriBoard provide the 4 pin power connector (X502) for the Ethernet miniWiggler (EmW). This connectorshould be assembled by your self if needed.For the pinout of connector see Figure 6-13.The needed Samtec connector is the JST B4B-PH-K.The connector provide the input voltage to the Ethernet miniWiggler and an enable/wakeup signal connected toTLF35584 and a standby voltage of +1,25V connected to VDDSB of device. In case the EmW is used you mustremove R522. If R522 is removed then you must make sure that the EmW is always connected. Otherwise withassembled R522 (default) you should not connect the pin 4 of connector.The mentioned resistor is red marked in Figure 3-8

U201

R395

X404

R212

S502

R222 CB205

R379

R372

C305

C310

X306

CB313

CB314

CB315

C311

U307

Y301

X604

R249

R246R245

R244

X402

S201

R377

R204R205

R215R214

X201

X305

X304

X303

R240

R236

R234

R232

R230

R223

R361

R359

R211

D301

CB206

C303

U408U407U406

R451

R455

R456

R454

R446

R444

CB419

CB418

CB417

CB416

CB415

CB414

D401

R430R429

R423

CB405

C402

R411

BU401

L401

D402

R401

CB401

U404

U401

Y401

CB408

R403

R402

CB402

R344

R524

R424

R425

R426

R427

R428 CB520

R201

CB204

R203

R202

C201

C202

R206

R207 Y201

R337

R357

R324

R399

R391 R392 R393 R394 R396 R397

CB309

R532

C301

C302

R439

R531

R335

R336

R355

R356

U305

T301

T302

X301

X302

X602X603

X601

D302

D303

D304

D305

D306

D307

D308

D309

D505

D506

D507D504

X401

X501

S501

R354

C519

R452

CB203

R213R216

R398

U502C505

D508

U501

L502

L501 CB501

C502

C507

C509

C508

C501

C503

C504

R501

R507

R508

R509

CB502

R 231

R233

R235

R237

R 241

R255

R256

R390

R375

R376

R348

R349

R525

S202

X502

R346

R 347

R457

X406

C522

CB316

CB317

U308

R248




Figure 3-8 Resistor for VDDSB

X703

CB511

R388

R380

R378 Q301

R368

R371

R382

R419

R440

R369

R367

C320

C317

C316C315C314

C313

C312

Q403

R389

R383

R385

R370 CB311

CB312

C208

C207

C205

C204C203

R433

R523

R431

R381

R314

R252R250

R251R253

R254

CB202R208

R408

U306

R521

R238

R365R364

R363

R362

R360 CB310

C304

R449

R448R447

R445

R443

R413

U405

L402

CB4

13C403

D403

R404C401

R450

R442

R441

CB412

CB411

CB410

C405C404

R422

R421

U403

Q402

Q401

R412

C406

R420

R414

R418

R417 R416

R415

R410

R 409CB407

CB403

R407

U402

R406 R405

CB406

CB404

R305

R306

R308 R309

R315

R316

R318

R319

R522

R301

R311

R341

R340

R321

R322

R220R221

R533

R323

R343

CB301

CB302

CB512

CB513

CB515

CB5

16

CB517

CB518

CB5

19

R537

R307

R317

R538

R534

R513

R535

R536

C515

R511

R512

R510

Q502

Q504

Q503

X702

X704X701

U301

U302

R302

R342

CB303

CB304

CB305

CB306

CB307

CB308

R303

R304

R338

R330

R331

R358

R350

R351

U303

U304

R332

R334

R333

R352

R353

R320

CB201R209

CB510

R520

D503

R505

R504

C510

R502

R506

Q505 Q501

D501

C512

C511

D502

R503

R239

R312

R436

R437

R438

R313

R373

R374

Q506

L503

C520

C521

C506

CB506 U503

CB409R386

C306



TriBoard Configuration

4 TriBoard Configuration

4.1 HW Boot Configuration

Figure 4-1 HW Configuration DIP-Switches

The picture above shows the definition of the boot HW configuration switch. The meaning of the switches will bedescribed in the following table (Table 4-1).

Note: The ON position of the switch is equal to a logical LOW at the dedicated pin.

4.1.1 Default Pad StateP14.4 / HWCFG6 is used to select the Default Pad State. Dipswitch 1 used to select this.In case that dispswitch1 is set to ON then all I/O pins are in tristate otherwise the internal pull-up devices areenabled on the I/O pins. Please note that after change Dipswitch 1 you must make a power cycle (switch off ->switch on) to use the new configuration.In case that TriState is selected (Dipswitch 1 is set to ON) then the I/O pins are floating. If you need a specific levelon different pins during startup (e.g. driver pins) then you must add the needed pull device (up or down). Somepins (especially the HWCFG pins) haven always the needed external pull-up and/or pull-down resistor assembledon the board.

4.1.2 Bootmode

Table 4-1 User Startup Modes 1)2)3)

1) The shadowed line indicates the default setting.2) ’x’ represents the don’t care state.3) 2 to 4 are the Dip Switch numbers.

HWCFG[5...3] Type of Boot 2 3 4

XX1 Start-up mode is selected by Boot Mode Index X X OFF

110 Internal Start from Flash OFF OFF ON

100 Alternate Boot Mode, Generic Bootstrap Loader on fail (P14.0/P14.1) ON OFF ON

010 Alternate Boot Mode, ASC Bootstrap Loader on fail (P15.2/P15.3) OFF ON ON

000 Generic Bootstrap Loader (P14.0/P14.1) ON ON ON

2

on

1 3 4

P14.4

P10.5

P10.6

P14.3




4.2 Assembly Options

4.2.1 General optional resistors

Note: All resistors are red marked in the following figures

Table 4-2 General optional resistors (default assembly in brackets)

Component Description

R202 Connect P20.2 (/TESTMODE) to GND (not assembled)

R203 XTAL1 Rload (50 Ohm) (not assembled)

R206 XTAL Rparallel (not assembled)

R207 XTAL2 Rserial (assembled)

R238 Switch off EVRC (not assembled)

R240 Switch off EVR33 (not assembled)

R390 Connect V_STBY to toggle LEDs D302...D305 (assembled)

R399 Connect V_UC to toggle LEDs D306...D309 (assembled)

R423 Connect P20.0 with miniWiggler JDS (not assembled)

R424 Connect P20.0 with OCDS1 connector (not assembled)



R427 Connect P21.7 with USR1 of miniWiggler JDS (not assembled)

R428 Connect P20.2 with USR1 of miniWiggler JDS (not assembled)

R429 Connect P21.6 (DAP3) with USR1 of DAP (assembled)

R430 Connect P20.2 with USR1 of DAP (not assembled)

R433 Connect P21.7 with ETK connector (not assembled)

R439 Connect P21.7 with ETK connector (not assembled)

R508 Connect pin MPS of TLF35584 to V_CO (not assembled)

R509 Connect pin MPS of TLF35584 to Ground (assembled)

R524 Connect VDDP3 to V_UC (not assembled)

R525 Connect VDDP3 to +3V3 (not assembled)




Figure 4-2 Location of general optional resistors on Top Side

Figure 4-3 Location of general optional resistors on Bottom Side

U201

R395

X404

R212

S502

R222 CB205

R379

R372

C305

C310

X306

CB313

CB314

CB315

C311

U307

Y301

X604

R249

R246R245

R244

X402

S201

R377

R204R205

R215R214

X201

X305

X304

X303

R240

R236

R234

R232

R230

R223

R361

R359

R211

D301

CB206

C303

U408U407U406

R451

R455

R456

R454

R446

R444

CB419

CB418

CB417

CB416

CB415

CB414

D401

R430R429

R423

CB405

C402

R411

BU401

L401

D402

R401

CB401

U404

U401

Y401

CB408

R403

R402

CB402

R344

R524

R424

R425

R426

R427

R428 CB520

R201

CB204

R203

R202

C201

C202

R206

R207 Y201

R337

R357

R324

R399

R391 R392 R393 R394 R396 R397

CB309

R532

C301

C302

R439

R531

R335

R336

R355

R356

U305

T301

T302

X301

X302

X602X603

X601

D302

D303

D304

D305

D306

D307

D308

D309

D505

D506

D507D504

X401

X501

S501

R354

C519

R452

CB203

R213R216

R398

U502C505

D508

U501

L502

L501 CB501

C502

C507

C509

C508

C501

C503

C504

R501

R507

R508

R509

CB502

R 231

R233

R235

R237

R 241

R255

R256

R390

R375

R376

R348

R349

R525

S202

X502

R346

R 347

R457

X406

C522

CB316

CB317

U308

R248

X703

CB511

R388

R380

R378 Q301

R368

R371

R382

R419

R440

R369

R367

C320

C317

C316C315C314

C313

C312

Q403

R389

R383

R385

R370 CB311

CB312

C208

C207

C205

C204C203

R433

R523

R431

R381

R314

R252R250

R251R253

R254

CB202R208

R408

U306

R521

R238

R365R364

R363

R362

R360 CB310

C304

R449

R448R447

R445

R443

R413

U405

L402

CB4

13C403

D403

R404C401

R450

R442

R441

CB412

CB411

CB410

C405C404

R422

R421

U403

Q402

Q401

R412

C406

R420

R414

R418

R417 R416

R415

R410

R 409CB407

CB403

R407

U402

R406 R405

CB406

CB404

R305

R306

R308 R309

R315

R316

R318

R319

R522

R301

R311

R341

R340

R321

R322

R220R221

R533

R323

R343

CB301

CB302

CB512

CB513

CB515

CB5

16

CB517

CB518

CB5

19

R537

R307

R317

R538

R534

R513

R535

R536

C515

R511

R512

R510

Q502

Q504

Q503

X702

X704X701

U301

U302

R302

R342

CB303

CB304

CB305

CB306

CB307

CB308

R303

R304

R338

R330

R331

R358

R350

R351

U303

U304

R332

R334

R333

R352

R353

R320

CB201R209

CB510

R520

D503

R505

R504

C510

R502

R506

Q505 Q501

D501

C512

C511

D502

R503

R239

R312

R436

R437

R438

R313

R373

R374

Q506

L503

C520

C521

C506

CB506 U503

CB409R386

C306




4.2.2 Resistors for peripherals

Table 4-3 Resistors for peripherals (default assembly in brackets)


R220 Connect V_VR with VDDM (assembled)

R221 Connect +3V3 with VDDM (not assembled)

R222 Connect VAREF1 with VDDM (assembled)

R223 Connect VAREF2/AN43 with VDDM (assembled)

R301 Connect P20.7 with RXD of CAN0 transceiver (assembled)

R302 Connect P20.8 with TXD of CAN0 transceiver (assembled)

R303 Connect P14.1 with RXD of CAN0 transceiver (not assembled)

R304 Connect P14.0 with TXD of CAN0 transceiver (not assembled)

R311 Connect P13.1 with RXD of CAN1 transceiver (assembled)

R312 Connect P13.0 with TXD of CAN1 transceiver (assembled)

R313 Connect P00.1 with RXD of CAN1 transceiver (not assembled)

R314 Connect P00.0 with TXD of CAN1 transceiver (not assembled)

R320 Connect P02.0 with TXD of ERAY-A transceiver (assembled)

R321 Connect P02.4 with TXDEN of ERAY-A transceiver (assembled)

R322 Connect P02.1 with RXD of ERAY-A transceiver (assembled)

R323 Connect P10.1 with EN of ERAY-A transceiver (assembled)

R324 Connect P10.2 with ERRN of ERAY-A transceiver (assembled)

R340 Connect P02.2 with TXD of ERAY-B transceiver (assembled)

R341 Connect P02.5 with TXDEN of ERAY-B transceiver (assembled)

R342 Connect P02.3 with RXD of ERAY-B transceiver (assembled)

R343 Connect P20.10 with EN of ERAY-B transceiver (assembled)

R344 Connect P20.9 with ERRN of ERAY-B transceiver (assembled)

R348 Connect P15.4 with SCL of I2C Eeprom (assembled)

R349 Connect P15.5 with SDA of I2C Eeprom (assembled)

R364 Connect P15.1 with RXD of LIN1 transceiver (assembled)

R365 Connect P15.0 with TXD of LIN1 transceiver (assembled)

R368 Connect P11.9 with RXD1 of Ethernet PHY (assembled)

R369 Connect P11.10 with RXD0 of Ethernet PHY (assembled)

R370 Connect P11.11 with CRS_V of Ethernet PHY (assembled)

R371 Connect P11.12 with RXC and TXC of Ethernet PHY (assembled)

R372 Connect P11.6 with TXEN of Ethernet PHY (assembled)

R373 Connect P11.3 with TXD0 of Ethernet PHY (assembled)

R374 Connect P11.2 with TXD1 of Ethernet PHY (assembled)

R376 Disable outputs of MDIO/MDC transceiver (not assembled)

R377 Connect P10.3 with MDINT of Ethernet PHY (not assembled)

R436 Connect P14.0 with RXD of USB to UART (assembled)




Note: All resistors are red marked in the following figures

Figure 4-4 Location of peripheral resistors on Top Side

R437 Connect P14.1 with TXD of USB to UART (assembled)

R438 Connect P15.2 with RXD of USB to UART (not assembled)

R440 Connect P15.3 with TXD of USB to UART (not assembled)

Table 4-3 Resistors for peripherals (default assembly in brackets) (continued)


U201

R395

X404

R212

S502

R222 CB205

R379

R372

C305

C310

X306

CB313

CB314

CB315

C311

U307

Y301

X604

R249

R246R245

R244

X402

S201

R377

R204R205

R215R214

X201

X305

X304

X303

R240

R236

R234

R232

R230

R223

R361

R359

R211

D301

CB206

C303

U408U407U406

R451

R455

R456

R454

R446

R444

CB419

CB418

CB417

CB416

CB415

CB414

D401

R430R429

R423

CB405

C402

R411

BU401

L401

D402

R401

CB401

U404

U401

Y401

CB408

R403

R402

CB402

R344

R524

R424

R425

R426

R427

R428 CB520

R201

CB204

R203

R202

C201

C202

R206

R207 Y201

R337

R357

R324

R399

R391 R392 R393 R394 R396 R397

CB309

R532

C301

C302

R439

R531

R335

R336

R355

R356

U305

T301

T302

X301

X302

X602X603

X601

D302

D303

D304

D305

D306

D307

D308

D309

D505

D506

D507D504

X401

X501

S501

R354

C519

R452

CB203

R213R216

R398

U502C505

D508

U501

L502

L501 CB501

C502

C507

C509

C508

C501

C503

C504

R501

R507

R508

R509

CB502

R 231

R233

R235

R237

R 241

R255

R256

R390

R375

R376

R348

R349

R525

S202

X502

R346

R 347

R457

X406

C522

CB316

CB317

U308

R248




Figure 4-5 Location of peripheral resistors on Bottom Side

X703

CB511

R388

R380

R378 Q301

R368

R371

R382

R419

R440

R369

R367

C320

C317

C316C315C314

C313

C312

Q403

R389

R383

R385

R370 CB311

CB312

C208

C207

C205

C204C203

R433

R523

R431

R381

R314

R252R250

R251R253

R254

CB202R208

R408

U306

R521

R238

R365R364

R363

R362

R360 CB310

C304

R449

R448R447

R445

R443

R413

U405

L402

CB4

13C403

D403

R404C401

R450

R442

R441

CB412

CB411

CB410

C405C404

R422

R421

U403

Q402

Q401

R412

C406

R420

R414

R418

R417 R416

R415

R410

R 409CB407

CB403

R407

U402

R406 R405

CB406

CB404

R305

R306

R308 R309

R315

R316

R318

R319

R522

R301

R311

R341

R340

R321

R322

R220R221

R533

R323

R343

CB301

CB302

CB512

CB513

CB515

CB5

16

CB517

CB518

CB5

19

R537

R307

R317

R538

R534

R513

R535

R536

C515

R511

R512

R510

Q502

Q504

Q503

X702

X704X701

U301

U302

R302

R342

CB303

CB304

CB305

CB306

CB307

CB308

R303

R304

R338

R330

R331

R358

R350

R351

U303

U304

R332

R334

R333

R352

R353

R320

CB201R209

CB510

R520

D503

R505

R504

C510

R502

R506

Q505 Q501

D501

C512

C511

D502

R503

R239

R312

R436

R437

R438

R313

R373

R374

Q506

L503

C520

C521

C506

CB506 U503

CB409R386

C306



Signal (on board used) Description

5 Signal (on board used) DescriptionFor more information about the signals please see the user manual/datasheet for TC3X4 and/or the schematicsof the board.All not mentioned signals are not used on the board and can be used outside. Optional marked signals are usedonly if they are connected (default is that they are not used on the board).

5.1 Power Signals

5.2 Reset Signals

Table 5-1 Power Signals

Short name Description

VCC_IN Supply Input (3,5V...40V)

VIN Input Voltage of Power Supply Device

GND Ground

V_PREPEG Pre Regulator Voltage (~5,8V)

V_UC Microcontroller Supply Voltage (5V or 3,3V depends on assembled TLF35584)

V_CO Communication Supply Voltage (5V)

V_VR Reference Supply Voltage (5V)

V_STBY Standby Supply Voltage (5V or 3,3V depends on assembled TLF35584)

VDD Core Supply Voltage (1,25V)

VDDSB Emulation Stand-by SRAM Supply Voltage (1,25V)

VDDP3 Flash Power Supply Voltage (3,3V)

VFLEX Flexport Supply Voltage (3,3V)

VEXTOSC Oscillator Port Supply Voltage (5V or 3,3V depends on assembled TLF35584)

VDDOSC Oscillator Core Supply Voltage (1,25V)

VSSOSC Oscillator Ground

VDDM ADC Analog Part Supply Voltage (5V or 3,3V selectable via 0R resistors)

VAREF1 ADC Reference Voltage 1 (VDDM)

VAREF2 ADC Reference Voltage 2 (VDDM)

VDD_USB Supply Voltage from USB (5V)

VDD_FT Supply Voltage FT2232HL device (3,3V)

Table 5-2 Reset Signals


/PORST Power On Reset

/DBG_PORST Power On Reset from debug connectors

/ESR0 External Service Request 0 (Hardware Reset)

/ESR1 External Service Request 1 (Non Maskable Interrupt)




5.3 Config Signals

5.4 Clock Signals

5.5 Debug Signals

5.6 Peripheral Signals

Table 5-3 Config Signals


P14.5 HWCFG1 (EVR33OFF / EVR33ON)

P14.2 HWCFG2 (EVRCOFF / EVRCON)

P14.4 HWCFG6 (Pins in tristate / Pins with pull-up)

P14.3 HWCFG3 (Boot from pins / Boot from Flash BMI)

P10.5 HWCFG4 (see boot configuration Table 4-1)

P10.6 HWCFG5 (see boot configuration Table 4-1)

Table 5-4 Clock Signals


XTAL1 Crystal Oscillator Input

XTAL2 Crystal Oscillator Output

Table 5-5 Debug Signals


/TRST Test Reset

DAP0 Device Access Port Line 0 / Test Data Clock (TCK)

DAP1 Device Access Port Line 1 / Test Data Select (TMS)

DAP2 Device Access Port Line 2 / Test Data Output (TDO)

P21.6 Test Data Input (TDI)

DAP0_A DAP0 / TCK from debug connectors

DAP1_A DAP1 / TMS from debug connectors

P21.7 DAP2 / TDO from debug connectors / TriCore Breakpoint Input

P20.2 Test Mode Select Input

P20.0 TriCore Breakpoint Output

Table 5-6 Peripheral Signals


P14.1 ASCLIN0 Receive Input ACAN01 Receive Input B (optional)

P14.0 ASCLIN0 Transmit OutputCAN01 Transmit Output (optional)

P15.3 ASCLIN0 Receive Input B (optional)




P15.1 ASCLIN1 Receive Input A

P15.0 ASCLIN1 Transmit Output

P15.4 I2C0 Serial Clock

P15.5 I2C0 Serial Data Input C und Output

P20.7 CAN00 Receive Input B

P20.8 CAN00 Transmit Output

P13.1 CAN10 Receive Input D

P13.0 CAN10 Transmit Output

P00.1 CAN10 Receive Input A (optional)

P00.0 CAN10 Transmit Output (optional)

P02.0 E-Ray Channel A Transmit Data Output

P02.4 E-Ray Channel A Transmit Data Output enable

P02.1 E-Ray Channel A Receive Data Input 2

P10.1 E-Ray Channel A Enable Output

P10.2 E-Ray Channel A Error Input

P02.2 E-Ray Channel B Transmit Data Output

P02.5 E-Ray Channel B Transmit Data Output enable

P02.3 E-Ray Channel B Receive Data Input 2

P20.10 E-Ray Channel B Enable Output

P20.9 E-Ray Channel B Error Input

P11.2 Ethernet TXD1 Output

P11.3 Ethernet TXD0 Output

P11.6 Ethernet TXEN Output

P11.9 Ethernet RXD1 Input A

P11.10 Ethernet RXD0 Input A

P11.11 Ethernet CRSDV Input A

P11.12 Ethernet REFCLK Input A

P02.8 Ethernet Management Data Clock Output (MDC)

P00.0 Ethernet Management Data Input/Output (MDIO)

P10.3 Ethernet MD Interrupt Input (optional)

P14.6 QSPI2 Slave Select Output 2 for SCS of TLF35584

P15.8 QSPI2 Master Clock Output for SCL of TLF35584

P15.6 QSPI2 Master Transmit Output for SDI of TLF35584

P15.2 QSPI2 Master Receive Input E for SDO from TLF35584ASCLIN0 Transmit Output (optional)

P02.7 Output for Watchdog Input of TLF35584

P33.8 SMU_FSP0 Output for Error Signal Input of TLF35584

P33.9 Input for Safe State Signal 1 from TLF35584

Table 5-6 Peripheral Signals (continued)





P33.10 Output for Wake/Inhibit Input of TLF35584

P20.0 HSCT System Clock

P21.2 HSCT Data Negative Input

P21.3 HSCT Data Positive Input

P21.4 HSCT Data Negative Output

P21.5 HSCT Data Positive Output

P20[11...14] On board LED’s

P33[4...7] On board LED’s (standby voltage supplied)

Table 5-6 Peripheral Signals (continued)




Connector Pin Assignment

6 Connector Pin AssignmentThe TriBoard will be shipped with four male (plug) connectors on top layer and four female (socket) connectorson bottom layer. The default connectors are 80-pol. Board to Board connectors from Samtec:

http://www.samtec.com

Plug:FTSH-140-02-L-DV-ES-A

Socket:FLE-140-01-G-DV-A

6.1 On Board only used signalsFollowing port pins are only used on board and are not connected to any connector also not via resistor:

Table 6-1 On Board only used Signals


P32.0 Used as VGATE1N for EVRC

P32.1 Used as VGATE1P for EVRC

P14.2 Used as HWCFG2



http://www.samtec.com




6.2 TC3X4 Connector / Top View

Figure 6-1 Connector for TC3X4 - Pinout (Part I, Top View)

GND 1 2 GND GND 1 2 GNDGND 3 4 GND GND 3 4 GND

5 6 P21.6 VCC_IN 5 6 VCC_IN7 8 P21.7 VCC_IN 7 8 VCC_IN9 10 9 10

11 12 11 1213 14 13 1415 16 /ESR1 15 16 /ESR017 18 17 1819 20 GND 19 20 GND21 22 21 22 /PORST23 24 P10.5 23 2425 26 25 2627 28 P10.2 27 28 P23.129 30 P13.1 29 30 P22.131 32 P13.0 31 32 P22.033 34 P13.3 33 34 P22.335 36 P13.2 35 36 P22.237 38 P20.9 37 38 P20.1039 40 P20.13 39 40 P00.441 42 P33.5 41 42 P20.643 44 P20.3 43 44 P20.245 46 P00.0 45 46 P00.347 48 P00.1 47 48 P00.249 50 P21.2 GND 49 50 GND51 52 P21.3 XTAL1 51 52 P32.453 54 P21.4 XTAL2 53 5455 56 P21.5 P15.3 55 56 P15.557 58 P15.2 57 58 P15.459 60 P14.1 59 60 P15.161 62 P14.0 61 62 P15.063 64 P20.11 63 64 P00.1265 66 P20.14 65 6667 68 P20.12 67 68 P00.569 70 P20.7 69 70 P20.871 72 P20.0 P15.8 71 7273 74 73 74 P10.375 76 VDDSB 75 76 GND77 78 VEXT 77 78 +3V379 80 VEXT 79 80 +3V3

BUS EXPANSION (X601,X701) PERIPHERALS (X602,X702)




Figure 6-2 Connector for TC3X4 - Pinout (Part II, Top View)

GND 1 2 GND GND 1 2 GNDGND 3 4 GND GND 3 4 GNDAN0 5 6 AN16 P00.9 5 6AN1 7 8 AN17 7 8AN2 9 10 P02.0 9 10AN3 11 12 P02.1 11 12AN4 13 14 AN20 P02.2 13 14AN5 15 16 AN21 P02.3 15 16 P14.6AN6 17 18 P02.4 17 18AN7 19 20 P02.5 19 20AN8 21 22 AN24 21 22

23 24 AN25 23 24AN10 25 26 25 26 P15.6AN11 27 28 27 28 P15.7AN12 29 30 29 30AN13 31 32 31 32

33 34 P10.1 33 3435 36 P10.6 35 36

GND 37 38 GND 37 38VDDM 39 40 VAREF1 39 40GND 41 42 VAREF2 / AN43 41 42GND 43 44 GND 43 44

45 46 P11.2 45 4647 48 P11.3 47 4849 50 49 50

AN35 51 52 51 52AN36 53 54 AN44 P11.6 53 54AN37 55 56 AN45 55 56 P33.8AN38 57 58 AN46 57 58 P33.9AN39 59 60 AN47 P11.9 59 60 P33.10GND 61 62 GND P11.10 61 62 P33.13

63 64 P33.6 P11.11 63 6465 66 P11.12 65 6667 68 P33.4 67 68

VEXT 69 70 +3V3 69 70P02.6 71 72 P00.6 71 72P02.7 73 74 P00.7 73 74P02.8 75 76 P00.8 VFLEX 75 76P33.7 77 78 P14.3 VEXT 77 78 +3V3P33.11 79 80 P33.12 VEXT 79 80 +3V3

ADC (X603, X703) GTM / PORTS (X604,X704)




6.3 Power connector pinout

Figure 6-3 Power connector pinout (Roka 520 2550

6.4 USB connector pinout

Figure 6-4 USB connector pinout (Micro USB B-type)

6.5 FlexRay™ (ERAY) connector pinout

Figure 6-5 FlexRay™ (ERAY) connector pinout (IDC10)

6.6 CAN connector pinout

Figure 6-6 CAN connector pinout (IDC10)

+3,5V...40V

GND

D+

D-

VC

C

GN

DID

2 4 6 8

GN

D

BP BM

1 3 5 7 9

10

2 4 6 8

GN

D

CA

NH

CAN

L

1 3 5 7 9

10

GN

D




6.7 LIN connector pinout

Figure 6-7 LIN connector pinout (IDC10)

6.8 HSCT connector pinout

Figure 6-8 HSCT connector pinout (IEE1394 6-conductor)

6.9 Ethernet connector pinout

Figure 6-9 Ethernet connector pinout (RJ45)

2 4 6 8

GN

D

BUS

VIN

opt

1 3 5 7 9

10

GN

D

3

62

TXD

_P

RXD

_P

1 5

4

GN

D

GN

D

TXD

_N

RXD

_N

SYSC

LKJ2J1 J3 J4 J5 J6 J7 J8




6.10 OCDS1 connector pinout

Figure 6-10 OCDS1 connector pinout (IDC16)

6.11 DAP connector pinout

Figure 6-11 DAP connector pinout (Samtec FTSH10)

TDO

2 4 6 8

1 3 5 7 9

10 12 14 16

11 13 15

TDI

/TR

ST

TCK

/BR

KIN

TMS

GN

D

GN

D

/PO

RST

/BR

KOU

T

GN

D

V_U

C

DA

P0

2 4 6 8

1 3 5 7 9

10

US

R1_

IO

/PO

RS

T

US

R0_

IO

DA

P1

GN

D

GN

D

Key

GN

D

V_U

C




6.12 ETK connector pinout

Figure 6-12 ETK connector pinout (Samtec TFM-105)

6.13 Ethernet miniWiggler power connector pinout

Figure 6-13 Ethernet miniWiggler connector pinout (JST B4B-PH)

TDO

/ D

AP2

2 4 6 8

1 3 5 7 9

10

V_U

C

/PO

RST

TDI

TCK

/ D

AP0

/TR

ST

TMS

/ DA

P1

BRK

IO

/ES

R0

GN

D

2 41 3

WAK

EUP

VD

DSB

VCC

_IN

GN

D



Schematic and Layout

7 Schematic and Layout

7.1 Known problems

7.1.1 Known problems on TriBoard TC3X4L TH V1.0No problems known.

7.1.2 Known problems on TriBoard TC3X4L V1.0No problems known.

7.2 Schematic




Figure 7-1 Schematic - Project

11

22

33

44

55

66

77

88

DD

CC

BB

AA

1In

fineo

n Te

chno

logi

es A

GA

TV M

C A

CE

ATV

CES

Am

Cam

peon

1-1

2D

-855

79 N

eubi

berg

Tel.:

+49

-89-

234-

0

7

15.1

0.20

18

Num

ber:

Dat

e:

Shee

t:of

Tri

Boa

rd T

C3X

4L P

roje

ct

1.0

Rev

isio

n:

G:\T

echn

ical

_Sup

port

\Tri

Core

\Tri

Boar

d\ED

A_D

XP\T

riBo

ard

AURI

X 2G

\Tri

Boar

d TC

3X4L

\Tri

Boar

d TC

3X4L

V1.

X\Tr

iBoa

rd_T

C3X

4L_V

10.p

rjFi

le:

XTA

L[1.

.2]

DEB

UG

..

POR

T[00

..33]

AN

[0..4

7]

Clo

ck, C

onfig

, Deb

ug, P

orts

and

AD

CC

lk_C

fg_D

bg_P

orts

_Adc

.sch

POR

T[00

..33]

/ESR

0

On

Boa

rd P

erip

hera

lsPe

riphe

rals

.sch

DEB

UG

..

POR

T[00

..33]

/ESR

0

/PO

RST

min

iWig

gler

and

Deb

ug C

onne

ctor

sw

iggl

er_D

bg_c

on.sc

h

/PO

RST

/ESR

0

/ESR

1

POR

T[00

..33]

Pow

er S

uppl

ySu

pply

.sch

XTA

L[1.

.2]

POR

T[00

..33]

AN

[0..4

7]

/PO

RST

/ESR

0

/ESR

1

NC

1[5.

.80]

NC

2[5.

.80]

NC

4[5.

.80]

NC

3[5.

.80]

Con

nect

or P

lug

Con

nect

m.sc

h

XTA

L[1.

.2]

POR

T[00

..33]

AN

[0..4

7]

/PO

RST

/ESR

0

/ESR

1

NC

1[5.

.80]

NC

2[5.

.80]

NC

4[5.

.80]

NC

3[5.

.80]Con

nect

or S

ocke

tC

onne

ctf.s

ch

NC4[5..80]

NC3[5..80]

NC2[5..80]

PORT[00..33]

AN

[0..4

7]

XTA

L[1.

.2]

/ESR

0

/PO

RST

/ESR

1

DEB

UG

..

NC1[5..80]




Figure 7-2 Schematic - Clock, Config, Debug, Ports and ADC

11

22

33

44

55

66

77

88

DD

CC

BB

AA

2In

fineo

n Te

chno

logi

es A

GA

TV M

C A

CE

ATV

CES

Am

Cam

peon

1-1

2D

-855

79 N

eubi

berg

Tel.:

+49

-89-

234-

0

7

15.1

0.20

18

Num

ber:

Dat

e:

Shee

t:of

Tri

Boa

rd T

C3X

4L C

lock

, Con

fig, D

ebug

, Por

ts, A

DC

1.0

Rev

isio

n:

G:\T

echn

ical

_Sup

port

\Tri

Core

\Tri

Boar

d\ED

A_D

XP\T

riBo

ard

AURI

X 2G

\Tri

Boar

d TC

3X4L

\Tri

Boar

d TC

3X4L

V1.

X\Cl

k_C

fg_D

bg_P

orts

_Adc

.sch

File

:

P21.6

POR

T[00

..33]

CLO

CK

& T

ESTM

OD

E

JTA

G /

DA

P / O

CD

S1

XTA

L181

XTA

L282

VSS

(OSC

)80

P20.

2 / T

ESTM

OD

E94

VEX

T(O

SC)

83

VD

D(O

SC)

79

TRST

91

TCK

/ D

AP0

92

P21.

6 / T

DI

88TM

S / D

AP1

89

P21.

7 / T

DO

/ D

AP2

90

U20

1B

TC3X

4_LQ

FP

P15.

5 / S

DA

011

4

P20.

1010

4

P20.

1410

8

P11.

6 / T

XEN

134

P11.

9 / R

XD

1A13

5

P11.

3 / T

XD

013

3

P14.

1 / A

RX

0A11

9P1

4.0

/ ATX

011

8

P15.

1 / A

RX

1A11

0P1

5.0

/ ATX

110

9

P20.

1110

5

P20.

1210

6

P20.

1310

7

P20.

8 / C

AN

00_T

XD

102

P20.

9 / R

EQ7_

010

3

VFL

EX13

6

P11.

12 /

REF

CLK

A13

9

P11.

10 /

RX

D0A

137

P11.

2 / T

XD

113

2

P15.

4 / S

CL

113

P33.

561

P20.

7 / C

AN

00_R

XD

B10

1

P11.

11 /

RX

DV

A13

8

ON

BO

AR

D U

SED

PER

IPH

ERA

LS /

PIN

S

P15.

6 / M

TSR

211

5

P33.

763

P33.

460

P33.

662

ASC

LIN

CA

N

QSP

I / T

LF35

584

ERA

Y

I2C LE

Ds

P14.

4 / H

WC

FG6

122

P14.

2 / H

WC

FG2

120

P33.

8 / S

MU

_FSP

064

P33.

965

P21.

3 / R

XD

0P85

P21.

4 / T

XD

0N86

P21.

5 / T

XD

0P87

P14.

3 / H

WC

FG3

121

P10.

5 / H

WC

FG4

143

P10.

6 / H

WC

FG5

144

P20.

0 / S

YSC

LK93

P21.

2 / R

XD

0N84

HSC

TH

WC

FG

P33.

1066

P33.

1167

ETH

ERN

ET

BU

TTO

N

P02.

0 / T

XD

0A1

P02.

1 / R

XD

0A2

P02.

2 / T

XD

0B3

P02.

3 / R

XD

0B4

P02.

4 / T

XEN

0A5

P02.

5 / T

XEN

0B6

P13.

1 / C

AN

10_R

XD

D12

9P1

3.0

/ CA

N10

_TX

D12

8

P15.

8 / S

CLK

211

7

P14.

5 / H

WC

FG1

123

P10.

2 / R

EQ2_

014

1

P10.

114

0

P14.

6 / S

LSO

2212

4

P15.

2 / M

RST

2E11

1

P10.

3 / R

EQ3_

014

2

P00.

0 / M

DIO

A11

P02.

8 / M

DC

9

P02.

78

U20

1C

TC3X

4_LQ

FP

POR

T[00

..33]

P20.2

P21.

7

GN

D

R20

6op

t

XTA

L[1.

.2]

XTA

L1

XTA

L2

R20

3

50R

_opt

VSS

OSC

DEB

UG

..

R20

7

0R

C20

210

pFC

201

10pF

VSS

OSC

VSS

OSC

1 2

Y20

120

MH

z

R20

110

K

V_U

C

P20.

2R

202

opt

GN

D

XTA

L[1.

.2]

R20

4

0R R20

5

0R

R21

6

0R

DAP2

R20

9

0RC

B20

133

0nR

208

0RC

B20

233

0n

VD

D

VSS

OSC

V_U

C

VSS

OSC

VD

DO

SC

VEX

TOSC

AN

[0..4

7]

V_V

R

CB

204

470n

GN

D

VD

DM

+3V

3

FOR

5V

AD

C

FOR

3,3

V A

DC

AN

0 / E

DS3

PA57

AN

1 / E

DS3

NA

56

AN

2 / E

DS0

PA55

AN

3 / E

DS0

NA

54

EVA

DC

/ ED

SAD

C

AN

453

AN

552

AN

651

AN

3534

AN

750

AN

849

AN

1048

AN

1147

AN

12 /

EDS0

PB46

AN

13 /

EDS0

NB

45

AN

1640

AN

17 /

P40.

1039

AN

20 /

EDS2

PA38

AN

21 /

EDS2

NA

37

AN

24 /

EDS2

PB /

P40.

036

AN

25 /

EDS2

NB

/ P4

0.1

35

AN

44 /

EDS1

PC29

AN

45 /

EDS1

NC

28

AN

46 /

EDS1

PD27

AN

47 /

EDS1

ND

26

VA

GN

D1

41

VA

REF

142

VD

DM

44

VSS

M43

AN

36 /

EDS1

PA /

P40.

633

AN

37 /

EDS1

NA

/ P4

0.7

32

AN

38 /

EDS1

PB /

P40.

831

AN

39 /

EDS1

NB

/ P4

0.9

30

VA

GN

D2

/ AN

4225

VA

REF

2 / A

N43

24

U20

1E

TC3X

4_LQ

FP

R22

2

6R8

CB

205

2,2μ

F

GN

D

VA

REF

1V

DD

M

R22

3

6R8

CB

206

2,2μ

F

GN

D

VA

REF

2V

DD

M

R22

0

1R2

R22

1

1R2_

opt

POR

TS

P13.

313

1P1

3.2

130

P32.

472

P00.

1221

P00.

920

P00.

415

P00.

516

P00.

314

P00.

213

P00.

112

P20.

395

P20.

610

0

P00.

819

P00.

718

P00.

617

P02.

67

P33.

1268

P33.

1369

P22.

377

P22.

276

P15.

311

2

P22.

074

P22.

175

P15.

711

6

P23.

173

U20

1D

TC3X

4_LQ

FP

P00.

1P0

0.2

P00.

3P0

0.4

P00.

5P0

0.6

P00.

7P0

0.8

P00.

9

P00.

12

GN

D

Switc

h O

N m

eans

the

corr

espo

ndin

g si

gnal

is lo

w.

Switc

h O

FF m

eans

the

corr

espo

ndin

g si

gnal

is h

igh.

R23

0

1K5

R23

2

1K5

R23

4

1K5

R23

6

1K5

R24

0

1K5_

opt

R23

8

1K5_

opt

P14.

5

P14.

2

P14.

4

P10.

5

P10.

6

P14.

3H

WC

FG3

HW

CFG

4

HW

CFG

5

HW

CFG

6

(abo

ut c

onfig

urat

ion

see

the

man

ual o

f ass

embl

ed d

evic

e)

GN

D

1 2 3 4

8 7 6 5

1S201

DIP

SW-4

R23

147

K

R23

347

K

R23

547

K

R23

747

K

R23

947

K

R24

147

K

V_U

C

V_U

C

V_U

C

V_U

C

V_U

C

V_U

C

NO

TE

: S2

01 is

for

devi

ce c

onfig

urat

ion

S202

P33.

11

R25

6

1K5

R25

547

K

V_S

TBY

GN

D

DAP2

/TR

STD

AP0

DA

P1

DEB

UG

..

R21

2 33R

R21

40R R

215

0RDA

P0

DA

P0_A

DA

P1

DA

P1_A

R21

3

33R

P13.

1

P15.

1

P14.

1

P14.

6

P10.

2

P13.

0

P15.

4

P14.

0

P15.

0

P02.

7

P02.

2P2

0.9

P20.

10

SYSC

LK

P33.

8

P02.

3

P20.

7P2

0.8

P15.

2

P15.

5

P02.

5

P33.

10

VFL

EXR

211

0R

+3V

3

CB

203

100n

P02.

1

P10.

1

RX

D0_

PR

XD

0_N

P15.

8

TXD

0_P

TXD

0_N

P15.

6

P33.

9

P02.

4P0

2.0

SYSC

LK1

TXD

P3

GN

D2

TXD

N4

S

RX

DP

5

RX

DN

6

X20

1

HSC

T0-o

pt

GN

D

R25

4

0RR25

3

0R R25

0

0R R25

1

0RR25

2

0R

P21.

2

P21.

5

P21.

4

P20.

0

P21.

3

P33.11

C20

747

nF

GN

D

AN

44

C20

847

nF

GN

D

AN

45

GN

D

AN

7

C20

347

nF

C20

447

nF

GN

D

AN

20

C20

547

nF

GN

D

AN

21

R24

9

4K7

R24

8

4K7

R24

4

4K7

R24

5

4K7

R24

6

4K7

GN

DP33.

6

P33.

4P3

3.5

P33.

7

P11.

3P1

1.2

P11.

6

P02.

6P2

3.1

P15.

3

AN[0..47]

AN

0A

N1

AN

2A

N3

AN

4A

N5

AN

6

AN

8A

N7_

I

AN

10A

N11

AN

12A

N13

AN

16A

N17

AN

20_I

AN

21_I

AN

24A

N25 AN

46A

N47

AN

44_I

AN

45_I

AN

35A

N36

AN

37A

N38

AN

39

P10.

5P1

0.6

P14.

4

P14.

3

P33.

11

P20.

12

P20.

14

P20.

11

P20.

13

P11.

12P1

1.10

P11.

9P1

1.11

P14.

2P1

4.5

P02.

8P0

0.0

P10.

3

P33.

12P3

3.13

P32.

4

P15.

7

P20.

3

P20.

6

P22.

0P2

2.1

P22.

3P2

2.2

P13.

2P1

3.3




Figure 7-3 Schematic - On Board Peripherals

11

22

33

44

55

66

77

88

DD

CC

BB

AA

3In

fineo

n Te

chno

logi

es A

GA

TV M

C A

CE

ATV

CES

Am

Cam

peon

1-1

2D

-855

79 N

eubi

berg

Tel.:

+49

-89-

234-

0

7

15.1

0.20

18

Num

ber:

Dat

e:

Shee

t:of

Tri

Boa

rd T

C3X

4L O

n B

oard

Per

iphe

rals

1.0

Rev

isio

n:

G:\T

echn

ical

_Sup

port

\Tri

Core

\Tri

Boar

d\ED

A_D

XP\T

riBo

ard

AURI

X 2G

\Tri

Boar

d TC

3X4L

\Tri

Boar

d TC

3X4L

V1.

X\Pe

riph

eral

s.sch

File

:

V_C

O

R30

5

0R

GN

D

R30

712

0R

R30

8

0R R30

9

0RG

ND

2

RX

D4

CA

NH

7

TXD

1

VC

C3

CA

NL

6

STB

8

VIO

5U

301

TLE9

251V

SJ

R30

60R

V_U

C

V_C

O

R31

5

0R

GN

D

R31

712

0R

R31

8

0R R31

9

0RG

ND

2

RX

D4

CA

NH

7

TXD

1

VC

C3

CA

NL

6

STB

8

VIO

5U

302

TLE9

251V

SJ

R31

60R

V_U

C

R30

1

0R

P00.

0

P00.

1

1 3 5 7 9

2 4 6 8 10

X30

1

CA

N0

1 3 5 7 9

2 4 6 8 10

X30

2

CA

N1

GN

D

GN

D

POR

T[00

..33]

CB303100n

CB304100n

CB305100n

GN

DG

ND

GN

D

VIN

V_C

OV

_UC

BPA

BM

A

CB306100n

CB307100n

CB308100n

GN

DG

ND

GN

D

VIN

V_C

OV

_UC

BPB

BM

B

ERR

NA

ERR

NB

R35

0

4K7

R35

1

4K7

V_U

C

R33

0

4K7

R33

1

4K7

V_U

C

GN

D

GN

D

12 3

4

T301

B82

789-

C01

04

C30

110

nF

GN

DR33

70R

R33

551

RR

336

51R

C30

210

nF

GN

DR35

70R

R35

551

RR

356

51R

R33

3op

t

R33

84K

7

V_U

C R35

84K

7

V_U

CENA

ENB

TXD

ATX

ENA

RX

DA

TXD

BTX

ENB

RX

DB

BG

EA

BG

EB

R33

4op

t

R33

2op

t

GN

D

R35

3op

tR

354

opt

R35

2op

t

GN

D

R32

3

0R R34

3

0R

CB

301

100n

GN

D

CB

302

100n

GN

D

V_U

C

GN

DCB

309

100n

P15.

4

P15.

5

R34

2

0RR34

1

0RR34

0

0R R34

4

0RR32

4

0RR32

1

0R

P20.

9

R32

0

0R

P10.

2

R32

2

0R

POR

T[00

..33]

SDA

3

VC

C4

SCL

1

VSS

2

U30

5

24A

A02

E48-

E/O

T

P10.

1

P20.

10

P02.

4

P02.

5

P02.

1

P02.

0

P02.

3

P02.

2

1 3 5 7 9

2 4 6 8 10

X30

3

ERA

Y-A

1 3 5 7 9

2 4 6 8 10

X30

4

ERA

Y-B

GN

D

R36

2

0R

R36

01K

CB

310

100n

GN

D

C30

322μF

/50V

GN

D

P15.

0

P15.

1

R36

5

0RR36

4

0RR36

3

10K

V_U

C

13

2

D30

1

BA

T54-

04

1 3 5 7 9

2 4 6 8 10

X30

5

LIN

1

R36

1

10K

VIN

R35

9

0R_o

pt

GN

D

GN

D

V_U

C

VIN

VIN

EN2

INH

8

BU

S6

TXD

4

WK

3

RX

D1

VS

7G

ND

5U

306

TLE7

259-

3GE

C30

41n

GN

D

P20.

7

P20.

8

12 3

4

T302

B82

789-

C01

04

TXD

4

BG

E7

TXD

EN5

RX

D6

EN2

STB

N8

RX

EN9

ERR

N10

GN

D13

INH

1

WA

KE

12

BP

15

BM

14

VB

AT

11

VD

D16

VIO

3

U30

3

TLE9

221S

X

GN

D

INH

A

GN

DG

ND

TXD

4

BG

E7

TXD

EN5

RX

D6

EN2

STB

N8

RX

EN9

ERR

N10

GN

D13

INH

1

WA

KE

12

BP

15

BM

14

VB

AT

11

VD

D16

VIO

3

U30

4

TLE9

221S

X

GN

D

INH

B

GN

DG

ND

R31

1

0RR

312

0R

P13.

1

P13.

0

R31

3

0R_o

ptR

314

0R_o

pt

R30

2

0RR

303

0R_o

ptR

304

0R_o

ptP1

4.0

P14.

1V

_UC

R39

847

0R

D309

LBT673

D308

LBT673

P33.4R

390

0R

R39

747

0R

P33.5

R39

647

0R

P33.6

R39

547

0R

P33.7 R39

447

0R

P20.11

R39

347

0R

P20.12

R39

247

0R

P20.13

R39

147

0R

P20.14

D307

LBT673

D306

LBT673

D305

LBT673

D304

LBT673

D303

LBT673

D302

LBT673

V_S

TBY

R39

9

0R

R34

8

0R R34

9

0R

R34

62K

R34

72K

V_U

CV

_UC

TD+

1

CT

4

RD

+3

TD-

2

CT

5

RD

-6

GN

D8

LK10

LA9

RA

12R

K11

SHIE

LDS

X30

6

RJ4

5

/ESR

0

C31

0 27pF

C31

1 27pF

GN

D

GN

D

1 3

Y30

1

NX

3225

SA-2

5MH

z+3

V3

RST

N

2

6 1

Q30

1AB

SD23

5N

5

3 4

Q30

1BB

SD23

5N

GN

D

GN

D

R38

1

10K

R38

010

K

R37

5

10K

R37

6

opt

P02.

8P0

0.0

R38

22K

49/1

%

GN

DG

ND

C30

5

22μF

GN

D

CB

311

100n

GN

D

+3V

3

LED

0 / P

HY

AD

[0] /

PM

EB24

LED

1 / P

HY

AD

[1]

25

CK

XTA

L131

CK

XTA

L232

EPA

DH

S

MD

I-[0

]4

MD

I+[0

]3

MDIO23

MDC22

TXC15

PHY

RST

B21

RSE

T1

RTL

8201

FI

TXD[0]16

TXD[1]17

TXD[2]18

TXD[3]19

RXD[0]9 RXD[1]10 RXD[2]/INTB11 RXD[3]/CLK_CTL12

TXEN20

RXC13

MD

I-[1

]6

MD

I+[1

]5

AVDD10OUT 2

AVDD33 7

DVDD10OUT 29

DVDD33 14

AVDD33 30

COL27

CRS/CRS_DV26

RXDV8

RXER/FXEN28

U30

7R

TL82

01FI

-VC

-CG

GN

DR

388

510R

C31

7 10n

Shie

ld

GN

D

GN

D

+3V

3

GN

D

C31

3

100n

C31

4

10n

C31

5

10n

C31

6

100n

C31

2

1000

pF/2

KV

+3V

3R

385

4K7

R38

9

510R

R38

34K

7/E

SR0

CB

312

100n

CB

313

100n

CB

314

100n

R37

84K

7R

377

330R

_opt

P10.

3

+3V

3

R37

91K

8

+3V

3

C320opt

P11.

2

P11.

3

R38

6 4K7

CB

315

100n

GN

D

MD

I0_P

MD

I0_N

MD

I1_P

MD

I1_N

P11.

6

R37

4

0R

R37

3

0R

R37

2

0R

R37

1

0R

GN

D

R37

0

0R

R36

9

0R

R36

8

0R

P11.

11

P11.

10

P11.

9

P11.

12

R36

7

4K7

+3V

3O

E6

VC

CA

3V

CC

B7

A1

5

GN

D2

B1

8A

24

B2

1

U30

8

TXS0

102D

CU

T

GN

D

+3V

3C

B31

6

100n

CB

317

100n

V_U

C

GN

D+3

V3

GN

D

Shie

ld

C30

6 10n

GN

D




Figure 7-4 Schematic - miniWiggler JDS and Debug connectors

11

22

33

44

55

66

77

88

DD

CC

BB

AA

4In

fineo

n Te

chno

logi

es A

GA

TV M

C A

CE

ATV

CES

Am

Cam

peon

1-1

2D

-855

79 N

eubi

berg

Tel.:

+49

-89-

234-

0

8

15.1

0.20

18

Num

ber:

Dat

e:

Shee

t:of

Tri

Boa

rd T

C3X

4L m

iniW

iggl

er a

nd D

ebug

con

nect

ors

1.0

Rev

isio

n:

G:\T

echn

ical

_Sup

port

\Tri

Core

\Tri

Boar

d\ED

A_D

XP\T

riBo

ard

AURI

X 2G

\Tri

Boar

d TC

3X4L

\Tri

Boar

d TC

3X4L

V1.

X\W

iggl

er_D

bg_c

on.sc

hFi

le:

TMS

1

TDO

3

CPU

CLO

CK

5

TDI

7

TRST

9

TCK

11

BR

KIN

13

N.C

.15

VC

C2

GN

D4

GN

D6

POR

ST8

BR

KO

UT

10

GN

D12

OC

DSE

14

KEY

16

X40

1

OC

DS1

V_U

C

GN

D

DA

P0_A

DA

P1_A

/BR

KO

UT

/TR

ST

GN

D

/DB

G_P

OR

ST

R42

40R

_opt

R42

60R

_opt

R42

50R

_opt

VR

EF1

GN

D3

GN

D5

KEY

7

GN

D9

DA

P12

DA

P04

USE

R1

8U

SER

06

RES

ET10

X40

2

DA

P

DEB

UG

..

/BR

KIN

R42

8

0R_o

pt

R42

7

0R_o

pt

P20.0

POR

T[00

..33]

/PO

RST

POR

T[00

..33]

DEB

UG

..

EEC

S63

EEC

LK62

EED

ATA

61

TEST

13

SUSP

END

36

OSC

I2

DM

7

GND 1

VR

EGO

UT

49

RES

ET14

AGND 10

OSC

O3

DP

8

REF

6

GND 5

VR

EGIN

50

GND 11

VCCIO20

GND 15

VCCIO31

AD

BU

S016

AD

BU

S117

AD

BU

S218

AD

BU

S319

AD

BU

S421

AD

BU

S522

AD

BU

S623

AD

BU

S724

AC

BU

S026

AC

BU

S127

AC

BU

S228

BD

BU

S038

BC

BU

S048

BD

BU

S139

BC

BU

S152

BD

BU

S240

BC

BU

S253

BD

BU

S341

BD

BU

S443

BD

BU

S544

BD

BU

S645

BD

BU

S746

AC

BU

S329

AC

BU

S430

AC

BU

S532

AC

BU

S633

AC

BU

S734

BC

BU

S354

BC

BU

S455

BC

BU

S557

BC

BU

S658

BC

BU

S759

GND 25

GND 35

GND 47

GND 51

PWR

EN60

VCORE64

VCORE12

VCORE37

VCCIO42

VCCIO56

VPLL9

VPHY4

U40

1

FT22

32H

L

VB

US

1

D+

3D

-2

ID4

GN

D5

BU

401

Mic

ro U

SB

GN

D

R40

2

27R

R40

3

27R

R40

4

12K

/1%

C40

6

3,3u

F

VD

D_F

T

L401

MM

Z160

8R30

0A

CB

401

100n

GN

D

R40

1

1K

CB

403

100n

CB

402

100n

CB

404

100n

C40

110μ/

6V

GN

D

VD

D_F

T

R40

5

10K

R40

7

opt

R40

6

2K2

CB

406

100n

R45

0

1K_o

pt

CB

407

100n

GN

D

V_U

C

AD

BU

S0A

DB

US1

AD

BU

S2A

DB

US3

AD

BU

S4A

DB

US5

AD

BU

S6A

DB

US7

AC

BU

S0A

CB

US1

AC

BU

S2A

CB

US3

R40

910

K

V_U

C

TMS

/TR

ST_J

DA

P0_A

USR

0

/RES

ET

D40

1LB

T67

3

R41

110

0R

VD

D_F

T

/PO

RST

AD

BU

S0A

DB

US1

AD

BU

S2

AD

BU

S3

AD

BU

S4 AD

BU

S6A

CB

US0

AC

BU

S1

AC

BU

S5

AC

BU

S6

BD

BU

S0B

DB

US1

13

D40

3

BA

T54

USR

8

GN

D

R42

04K

7

V_U

C

DA

P1_A

TDI

/TR

ST

DA

P0_A

DA

P1_A

P15.3

P15.2

BD

BU

S0

BD

BU

S1

CB

409

100n

R41

268

0RD40

2LP

T67

K

VD

D_F

T

R41

4

4K7

R41

610

K

R41

8

10K

R41

710

K R41

9

10K

VD

D_F

TV

_UC

VD

D_F

TV

_UC

R41

510

K

V_U

C

R41

010

K

VD

D_F

T

R42

1op

tR

422

opt

GN

DG

ND

R44

00R

_opt

GN

D

GN

D

1 3

Y40

1N

X32

25SA

-12M

Hz

C40

4 8pF

C40

5 8pF

VD

D_F

T

GN

D

GN

D

R44

1

10K

VD

D_F

T

GN

D

VD

D_F

T

VD

D_F

T

R44

2

10K

OU

T3

GND 2

IN1

U40

5TL

E427

4GSV

33

GN

D

GN

D

CB

411

100n

CB

410

100n

CB

412

100n

GN

D

GN

D

C40

24u

7/6V

GN

D

CB

405

100n

VD

D_F

T

GN

D

L402

MM

Z160

8R30

0AC

403

4u7/

6V

GN

D

CB

413

100n

GN

D

GN

D

VD

D_F

T

VD

D_F

T

+1V

8

/OE

1V

CC

5

A2

GN

D3

Y4

U40

4

SN74

LVC

1G12

5

CB

408

100n

VD

D_F

T

GN

D

R44

310

K

VD

D_F

T

CB

415

100n

CB

414

100n

GN

D

VD

D_F

TV

_UC

GN

DR

444

4K7

GN

D

AD

BU

S2

AC

BU

S3

DIR

5

VC

CA

1V

CC

B6

A3

GN

D2

B4

U40

6

SN74

LVC

1T45

DB

V

DIR

5

VC

CA

1V

CC

B6

A3

GN

D2

B4

U40

7

SN74

LVC

1T45

DB

V

CB

417

100n

CB

416

100nV

DD

_FT

V_U

C

GN

DR

445

4K7

GN

DGN

D

AC

BU

S2

AC

BU

S5

GN

D

USR

1

DIR

5

VC

CA

1V

CC

B6

A3

GN

D2

B4

U40

8

SN74

LVC

1T45

DB

V

CB

419

100n

CB

418

100nV

DD

_FT

V_U

C

GN

D

GN

D

R44

64K

7

GN

DGN

D

AD

BU

S1

AC

BU

S5

AC

BU

S5A

CB

US4

P21.

7

P21.7P21.6

P21.

6

AC

BU

S7

AC

BU

S7A

CB

US6

AC

BU

S6

AC

BU

S7A

CB

US3

AC

BU

S2

R41

3

10K

R44

70R

_opt

R44

80R

_opt

R44

90R

_opt

AC

BU

S4

R45

4

5K1

DA

P1_A

OR

G6

DN

C7

VC

C8

CS

1

GN

D5

Q4

CLK

2

D3

U40

2

93LC

46B

-I/S

N

G1

1A1

21Y

118

1A2

41Y

216

1A3

61Y

314

1A4

81Y

412

VC

C20

GN

D10

2Y1

9

2Y2

7

2Y3

5

2Y4

3

G19

2A1

11

2A2

13

2A3

15

2A4

17

U40

3

SN74

AH

C24

4PW

R45

6

0R

P20.

0

R45

5

0R

P21.

7R

451

0R_o

pt

R42

3

0R_o

pt

FOR

USI

NG

WIG

GL

ER

WIT

H J

TA

G:

Ass

embl

e R

447-

R45

1R

emov

e R

455-

R45

6

P21.

6

P21.

7

P20.

0

P21.

7

2

61

Q40

1AB

SD23

5N

5

34

Q40

1BB

SD23

5N

2

61

Q40

2AB

SD23

5N

5

34

Q40

2BB

SD23

5N

2

61

Q40

3AB

SD23

5N

5

34

Q40

3BB

SD23

5N

VD

D_U

SB

R43

110

0K

V_U

C

/DB

G_P

OR

ST

GN

D1

TCK

/ D

AP0

2

/TR

ST3

TDO

/ D

AP2

4

TMS

/ DA

P15

TDI /

-6

BR

KIO

7V

DD

sens

e8

ESR

09

/PO

RST

10

X40

4

ETK

_CO

N_o

pt

V_U

C/D

BG

_PO

RST

/ESR

0

DA

P0_A

P21.

6

/ESR

0

P21.

7

P21.

7G

ND

DA

P1_A

/TR

STR

439 22

R_o

pt

R43

3

0R_o

pt

P21.7

P21.

7

P20.2P2

0.2

R43

70R

P14.1

P14.0

R43

60R

R43

80R

_opt

P21.

7

P20.

2

DA

P0_A

R40

8

0R/D

BG

_PO

RST

V_U

C

GN

D

DA

P3_U

SR1

DA

P0D

AP1

/DB

G_P

OR

ST

R43

00R

_opt

R42

90R

DA

P2

R45

2

0R

P21.6

P20.2

GN

D

VR

EF1

GN

D3

GN

D5

KEY

7

GN

D9

DA

P12

DA

P04

USE

R1

8U

SER

06

RES

ET10

X40

6

DA

P_SC

RP33.6P33.7

R45

7

0R

V_S

TBY




Figure 7-5 Schematic - Power Supply

11

22

33

44

55

66

77

88

DD

CC

BB

AA

5In

fineo

n Te

chno

logi

es A

GA

TV M

C A

CE

ATV

CES

Am

Cam

peon

1-1

2D

-855

79 N

eubi

berg

Tel.:

+49

-89-

234-

0

7

15.1

0.20

18

Num

ber:

Dat

e:

Shee

t:of

Tri

Boa

rd T

C3X

4L P

ower

supp

ly

1.0

Rev

isio

n:

G:\T

echn

ical

_Sup

port

\Tri

Core

\Tri

Boar

d\ED

A_D

XP\T

riBo

ard

AURI

X 2G

\Tri

Boar

d TC

3X4L

\Tri

Boar

d TC

3X4L

V1.

X\Su

pply

.sch

File

:

D50

4

LS T

67K

V_U

C

+1V

25V

DD

VD

DSB

S501

RES

ET

GN

D23

1Q

502

BC

848C

C51

54μ

7/10

V

GN

DG

ND

V_U

C

2 3

1Q

503

BC

858C

GN

D

V_U

C

/PORST

R51

31K

5

GN

DD50

7LP

T67

K

R51

268

0R

GN

DD50

6LP

T67

K

R51

162

0R

+3V

3

GN

D23

1Q

504

BC

848C

R51

0

82K

+1V

25

+3V

3V

_UC

D50

5LP

T67

K

CB

520

100n

GN

D

V_U

C

V_U

C

/PO

RST

/ESR

0

/ESR

1/E

SR1

/ESR

0

/PO

RST

/ESR

1

/ESR

0

/ESR

1

/PO

RST

/ESR

0

CB

512

100n

CB

513

100n

GN

D

GN

D

GN

D

+1V

25

C51

92,

2μF

GN

D

V_U

C

CB

515

100n

CB

516

100n

CB

517

100n

CB

518

100n

R52

1

0R

R52

2

0R

R52

3

0R

R52

40R

_opt

VD

DP3

V_U

C

R53

8

120R

R53

54K

7

R53

1

4K7

R53

210

K

R53

30R

R53

7

10K

R53

42K

2

R53

64K

7

GN

D

CB

519

100n

1

2

X50

1

POWER

VC

C_I

ND

501 M

SS2P

2 C50

2

100μ

F/40

VC

B50

110

0nG

ND

GN

D

V_P

RER

EGV

IN

GN

D

VIN

V_S

TBY

SW1

43

WD

I16

QST5

VS1

45

WA

K4

RSH

47

PG1

41V

S244

VST

2

ENA

3

AG1 6

SW2

42

FRE

24

RO

T17

INT

18

SDO

13

SCL

14

QU

C30

QC

O31

SYN

19

QT1

33

QT2

32

VC

I26

SEC

23

EVC

21

SCS

15

ERR

20

BSG

1R

SL48

STU

25

DR

G46

GND HS

SDI

12

SS1

11

SS2

10

QV

R29

AG2 7

AG3 8

AG4 28

AGS 9

TM22

GST

27

PG2

40

FB1

34

FB2

35

FB3

36

FB4

37

FB5

38

AG5 39

U50

1TL

F355

84Q

VV

S1/2

V_V

R

V_C

O

S502

ENA

GN

D

GN

D

C50

7

1μF/

10V

GN

D

C51

2

4,7μ

F/10

V

GN

D

V_U

C

QT1

QT2

GN

D

R50

7

100K

/PO

RST

1

3 2

Q50

5B

SS13

8N

/ESR

1

P14.

6

GN

D

P02.

7

C50

322μF

/10V

C50

8

4,7μ

F/10

VC

509

4,7μ

F/10

VC

510

4,7μ

F/10

VC

511

4,7μ

F/10

V

GN

D

GN

D

V_S

TBY

R50

610

0K

GN

D

R50

210

K

P33.

8

D50

2

SS26

VD

D_U

SB

L501

XA

L505

0-22

3MEB

L502

XA

L403

0-47

2MEC

R50

1

250m

R

4

3

1,2,5,6

Q50

1B

SL60

6SN

C50

147μF

/40V

GN

D

GN

D

GN

D

D50

3

SS22

_opt

GN

D

R50

80R R

509

20K

GN

D

V_C

O

CB

502

100n

R50

4

470R

D50

8

LP T

67K

GN

D

P15.

8P1

5.6

P15.

2

R50

5

10K

R50

3 1KP3

3.9

Q1

GND 6

SEN

SE/A

DJ

2

BY

P4

IN8

EN5

GND HS

U50

2TL

S205

B0E

JV33

GN

D

V_U

CC

505

10μF

C50

410

nF

+3V

3

GN

D

GN

D

VG

ATE

1N

2

71

8

3

456

Q50

6B

SZ15

DC

02K

D

GN

D

V_U

CC

521

22μF

L503

LTF5

022T

-3R

3N2R

5C

520

10μF

VG

ATE

1P

CB

510

100n

R52

00R

GN

D

V_S

TBY

1 32 4

X50

2

EmW

_Pw

r_op

t

GN

DV

DD

SB

VC

C_I

N

/PO

RST

R52

50R

_opt

+3V

3

P33.

10

POR

T[00

..33]

PORT[00..33]

C52

210μF

GN

D

PGND 8

LSC

ON

5

VC

C7

SW1

PWM

6SW

2

GND 4GND HS

PGND 3VS9 VS10

U50

3TL

F112

51_o

pt

C50

6

10μF

_optG

ND

V_U

C

GN

D

CB

506

100n

_opt

GN

D

GN

D

V_P

RER

EG

POW

ER

VEXT125

VEXT23

ESR

196

ESR

098

POR

ST97

VDD127

VEXT78

VDDP3126 P32.

0 / V

GA

TE1N

70

P32.

1 / V

GA

TE1P

71

VDD22 VDD58 VDD99 VSS HS

VDD/VDDSB10

VEVRSB59

U20

1ATC

3X4_

LQFP

CB

511

100n




Figure 7-6 Schematic - Connectors (Plug)

11

22

33

44

55

66

77

88

DD

CC

BB

AA

6In

fineo

n Te

chno

logi

es A

GA

TV M

C A

CE

ATV

CES

Am

Cam

peon

1-1

2D

-855

79 N

eubi

berg

Tel.:

+49

-89-

234-

0

7

15.1

0.20

18

Num

ber:

Dat

e:

Shee

t:of

Tri

Boa

rd T

C3X

4L C

onne

ctor

s plu

g

1.0

Rev

isio

n:

G:\T

echn

ical

_Sup

port

\Tri

Core

\Tri

Boar

d\ED

A_D

XP\T

riBo

ard

AURI

X 2G

\Tri

Boar

d TC

3X4L

\Tri

Boar

d TC

3X4L

V1.

X\Co

nnec

tm.sc

hFi

le:

PER

IPH

ERA

LS

POR

TS

TOP

PLU

G1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80

X60

1

FTSH

-140

-02-

L-D

V-E

S-A

PLU

G1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80

X60

2

FTSH

-140

-02-

L-D

V-E

S-A

PLU

G1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80

X60

4

FTSH

-140

-02-

L-D

V-E

S-A

PLU

G1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80

X60

3

FTSH

-140

-02-

L-D

V-E

S-A

AD

C

GN

D

/ESR

0

GN

D

VC

C_I

NV

CC

_IN

GN

DG

ND

GN

DG

ND

GN

DV

DD

SB

+3V

3V

_UC

XTA

L[1.

.2]

/PO

RST

/ESR

0/E

SR1

NC

2.9

NC

2.17

NC

2.11

NC

2.13

/ESR

1

P15.

3P1

5.2

P20.

14P2

0.12

NC

2.10

NC

2.14

/PO

RST

XTA

L1X

TAL2

NC

2.12

P15.

5

P15.

1P1

5.0

P14.

0P1

4.1

P15.

4

P20.

11

NC

2.18

NC

2.54

P15.

8N

C2.

73N

C2.

72P1

0.3

NC

2.21

P10.

5N

C2.

24

P10.

2P2

3.1

P13.

1P1

3.0

P13.

3P1

3.2

NC

2.25

P22.

1P2

2.0

P22.

3P2

2.2

NC

2.26

P20.

9P2

0.10

P20.

13P0

0.4

P20.

3P2

0.6

P33.

5P2

0.2

P00.

0P0

0.1

P00.

2P0

0.3

NC

2.66

P00.

5

P00.

12

P32.

4

NC

2[5.

.80]

NC

1[5.

.80]

NC

1[5.

.80]

NC

2[5.

.80]

XTA

L[1.

.2]

V_U

C+3

V3

GN

D

GN

DG

ND

POR

T[00

..33]

GN

DV

DD

MG

ND

VA

REF

1G

ND

GN

D

V_U

C+3

V3

P00.

8

P33.

12P1

4.3

P33.

11

P00.

6P0

0.7

GN

D

P02.

6P0

2.7

P02.

8P3

3.7

GN

D

P00.

9N

C4.

7P0

2.0

P02.

1P0

2.2

P02.

3P0

2.4

P02.

5N

C4.

21N

C4.

23N

C4.

25N

C4.

27N

C4.

29N

C4.

31P1

0.1

P10.

6N

C4.

37N

C4.

39

NC

4.67

NC

4.22

NC

4.24

P15.

6P1

5.7

NC

4.30

NC

4.32

NC

4.34

NC

4.36

NC

4.44

NC

4.42

P33.

9

NC

4[5.

.80]

P23.

2N

C4.

40

NC

4.46

POR

T[00

..33]

NC

4[5.

.80]

NC

4.50

NC

4.48

AN

[0..4

7]A

N[0

..47]

NC

4.54

P33.

8

P33.

10

NC

4.52

NC

4.66

P33.

13

NC

4.68

NC

4.64

P33.

6N

C3.

65N

C3.

66N

C3.

63

P33.

4N

C3.

67

P20.

7P2

0.8

NC

4.14

P14.

6N

C4.

18N

C4.

20

NC

4.12

NC

4.10

NC

4.8

NC

4.6

NC

4.69

NC

4.74

NC

4.72

NC

4.76

NC

4.71

NC

4.73

NC

4.70

VA

REF

2

VFL

EX

NC

1.5

NC

1.7

NC

1.9

NC

1.11

NC

1.13

NC

1.15

NC

1.17

NC

1.19

NC

1.21

NC

1.23

NC

1.25

NC

1.27

NC

1.29

NC

1.31

NC

1.33

NC

1.35

NC

1.37

NC

1.39

NC

1.41

NC

1.43

NC

1.45

NC

1.47

NC

1.49

NC

1.51

NC

1.53

NC

1.55

NC

1.57

NC

1.59

NC

1.61

NC

1.63

NC

1.65

NC

1.67

NC

1.69

NC

1.71

NC

1.73

NC

1.75

NC

1.77

NC

1.79

P21.

6P2

1.7

NC

1.10

NC

1.12

NC

1.14

NC

1.16

NC

1.18

NC

1.20

NC

1.22

NC

1.24

NC

1.26

NC

1.28

NC

1.30

NC

1.32

NC

1.34

NC

1.36

NC

1.38

NC

1.40

NC

1.42

NC

1.44

NC

1.46

NC

1.48

P21.

2P2

1.3

P21.

4P2

1.5

NC

1.58

NC

1.60

NC

1.62

NC

1.64

NC

1.66

NC

1.68

NC

1.70

P20.

0N

C1.

74

NC

1.80

NC

1.78

NC

1.76

AN

0A

N1

AN

2A

N3

AN

4A

N5

AN

6A

N7

AN

8N

C3.

23A

N10

AN

11A

N12

AN

13N

C3.

33N

C3.

35

AN

16A

N17

NC

3.10

NC

3.12

AN

20A

N21

NC

3.18

NC

3.20

AN

24A

N25

NC

3.26

NC

3.28

NC

3.30

NC

3.32

NC

3.34

NC

3.36

NC

3.45

NC

3.47

NC

3.49

AN

35A

N36

AN

37A

N38

AN

39

NC

3.46

NC

3.48

NC

3.50

NC

3.52

AN

44A

N45

AN

46A

N47

NC

4.41

NC

4.43

P11.

2P1

1.3

NC

4.49

NC

4.51

P11.

6N

C4.

55N

C4.

57P1

1.9

P11.

10P1

1.11

P11.

12

NC

3[5.

.80]

NC

3[5.

.80]




Figure 7-7 Schematic - Connectors (Socket)

11

22

33

44

55

66

77

88

DD

CC

BB

AA

7In

fineo

n Te

chno

logi

es A

GA

TV M

C A

CE

ATV

CES

Am

Cam

peon

1-1

2D

-855

79 N

eubi

berg

Tel.:

+49

-89-

234-

0

7

15.1

0.20

18

Num

ber:

Dat

e:

Shee

t:of

Tri

Boa

rd T

C3X

4L C

onne

ctor

s soc

ket

1.0

Rev

isio

n:

G:\T

echn

ical

_Sup

port

\Tri

Core

\Tri

Boar

d\ED

A_D

XP\T

riBo

ard

AURI

X 2G

\Tri

Boar

d TC

3X4L

\Tri

Boar

d TC

3X4L

V1.

X\Co

nnec

tf.sc

hFi

le:

BO

TTO

MSO

CK

ET1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80

X70

1

FLE-

140-

01-G

-DV

-A

SOC

KET

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80

X70

2

FLE-

140-

01-G

-DV

-A

SOC

KET

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80

X70

3

FLE-

140-

01-G

-DV

-A

SOC

KET

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80

X70

4

FLE-

140-

01-G

-DV

-A

GN

D

/ESR

0

GN

D

VC

C_I

NV

CC

_IN

GN

DG

ND

GN

DG

ND

GN

DV

DD

SB

+3V

3

PER

IPH

ERA

LS

POR

TS

V_U

C

XTA

L[1.

.2]

/PO

RST

/ESR

0/E

SR1

NC

2.9

NC

2.17

NC

2.11

NC

2.13

/ESR

1

P15.

3P1

5.2

P20.

14P2

0.12

NC

2.10

NC

2.14

/PO

RST

XTA

L1X

TAL2

NC

2.12

P15.

5

P15.

1P1

5.0

P14.

0P1

4.1

P15.

4

P20.

11

NC

2.18

NC

2.54

P15.

8P1

0.3

NC

2.21

P10.

5

P10.

2P2

3.1

P13.

1P1

3.0

P13.

3P1

3.2

NC

2.25

P22.

1P2

2.0

P22.

3P2

2.2

P20.

9P2

0.10

P20.

13P0

0.4

P20.

3P2

0.6

P33.

5P2

0.2

P00.

0P0

0.1

P00.

2P0

0.3

NC

2.66

P00.

5

P00.

12

P32.

4

NC

2[5.

.80]

NC

1[5.

.80]

NC

1[5.

.80]

NC

2[5.

.80]

XTA

L[1.

.2]

AD

C

V_U

C+3

V3

GN

D

GN

DG

ND

POR

T[00

..34]

GN

DV

DD

MG

ND

VA

REF

1G

ND

GN

D

V_U

C+3

V3

P00.

8

P33.

12P1

4.3

P33.

11

P00.

6P0

0.7

GN

D

P02.

6P0

2.7

P02.

8P3

3.7

GN

D

P00.

9N

C4.

7P0

2.0

P02.

1P0

2.2

P02.

3P0

2.4

P02.

5N

C4.

21N

C4.

23N

C4.

25N

C4.

27N

C4.

29N

C4.

31P1

0.1

P10.

6N

C4.

37N

C4.

39

NC

4.67

NC

4.22

NC

4.24

P15.

6P1

5.7

NC

4.30

NC

4.32

NC

4.34

NC

4.36

NC

4.44

NC

4.42

P33.

9

NC

4[5.

.80]

P23.

2N

C4.

40

NC

4.46

POR

T[00

..34]

NC

4[5.

.80]

NC

4.50

NC

4.48

AN

[0..4

7]A

N[0

..47]

NC

4.54

P33.

8

P33.

10

NC

4.52

NC

4.66

P33.

13

NC

4.68

NC

4.64

P33.

6

P33.

4

P20.

7P2

0.8

NC

4.14

NC

4.18

NC

4.20

NC

4.12

NC

4.10

NC

4.8

NC

4.6

NC

4.69

NC

4.74

NC

4.72

NC

4.76

NC

4.71

NC

4.73

NC

4.70

VA

REF

2

VFL

EX

NC

1.5

NC

1.7

NC

1.9

NC

1.11

NC

1.13

NC

1.15

NC

1.17

NC

1.19

NC

1.21

NC

1.23

NC

1.25

NC

1.27

NC

1.29

NC

1.31

NC

1.33

NC

1.35

NC

1.37

NC

1.39

NC

1.41

NC

1.43

NC

1.45

NC

1.47

NC

1.49

NC

1.51

NC

1.53

NC

1.55

NC

1.57

NC

1.59

NC

1.61

NC

1.63

NC

1.65

NC

1.67

NC

1.69

NC

1.71

NC

1.73

NC

1.75

NC

1.77

P21.

6P2

1.7

NC

1.10

NC

1.12

NC

1.14

NC

1.16

NC

1.18

NC

1.20

NC

1.22

NC

1.24

NC

1.26

NC

1.28

NC

1.30

NC

1.32

NC

1.34

NC

1.36

NC

1.38

NC

1.40

NC

1.42

NC

1.44

NC

1.46

NC

1.48

P21.

2P2

1.3

P21.

4P2

1.5

NC

1.58

NC

1.60

NC

1.62

NC

1.64

NC

1.66

NC

1.68

NC

1.70

P20.

0N

C1.

74

NC

1.78

NC

1.76

AN

0A

N1

AN

2A

N3

AN

4A

N5

AN

6A

N7

AN

8N

C3.

23A

N10

AN

11A

N12

AN

13N

C3.

33N

C3.

35

AN

16A

N17

AN

20A

N21

NC

3.18

NC

3.20

AN

24A

N25

NC

3.34

NC

3.36

NC

3.49

AN

35A

N36

AN

37A

N38

AN

39

NC

3.46

NC

3.48

NC

3.50

NC

3.52

AN

44A

N45

AN

46A

N47

NC

4.41

NC

4.43

P11.

2P1

1.3

NC

4.49

NC

4.51

P11.

6N

C4.

55N

C4.

57P1

1.9

P11.

10P1

1.11

P11.

12

NC

3[5.

.80]

NC

3[5.

.80]

NC

3.65

NC

3.66

NC

3.63

NC

3.67

NC

1.79

NC

1.80

NC

2.73

NC

2.72

NC

2.24

NC

2.26

NC

3.10

NC

3.12

NC

3.26

NC

3.28

NC

3.30

NC

3.32

NC

3.45

NC

3.47

P14.

6




7.3 Layout

Figure 7-8 Component Plot Top Layer

U201

R39

5

X404

R212

S502

R222

CB205

R379

R372

C305

C310

X306

CB3

13

CB3

14

CB315

C311

U307

Y301

X604

R249

R246

R245 R244

X402

S201

R377

R204

R20

5

R215

R21

4

X201

X305X304X303

R240

R236

R234

R232

R230

R223

R361

R359

R211

D301

CB206

C30

3

U408

U407

U406

R451

R455

R456

R454

R446

R444

CB419

CB418

CB417CB416

CB415

CB414

D40

1

R430

R429

R423

CB405

C402

R411

BU401

L401

D40

2

R401

CB401

U404

U401

Y401

CB408

R403

R402

CB402

R344

R52

4

R424

R425

R426

R427

R428

CB520

R201

CB204R203

R20

2

C201

C20

2

R206

R207

Y201

R337 R357

R324

R39

9

R391

R392

R393

R394

R39

6R3

97

CB309

R532

C301 C302

R439

R531

R335

R336

R355

R356

U305

T301 T302

X301 X302

X60

2X603

X601

D302

D303

D304

D305

D306

D307

D308

D309

D50

5

D50

6

D50

7D504

X401

X501

S501

R354

C519

R452

CB203

R213

R216

R398

U50

2C505

D508

U50

1

L502

L501

CB501

C502

C507

C509

C508

C501

C503

C504

R501

R50

7

R508 R509

CB502

R231

R233

R235

R237

R241

R255R256

R39

0

R375

R376

R348

R349

R525

S202

X502

R346

R347

R457

X406

C522

CB316

CB31

7

U308

R248




Figure 7-9 Component Plot Bottom Layer

X70

3

CB511

R388

R38

0

R378

Q30

1

R368

R37

1

R382

R41

9

R44

0

R36

9

R36

7

C320

C317

C31

6

C315

C314

C313

C312

Q403

R38

9

R383R385

R370

CB311 CB312

C208

C207

C20

5

C204

C203

R433

R52

3

R431

R381

R314

R252

R25

0

R251

R253

R254

CB2

02

R208

R408

U306

R52

1

R23

8

R365

R364

R363

R362

R360

CB310

C304

R449

R44

8

R44

7

R445

R443

R413

U405

L402

CB413C403

D403

R404

C401

R450

R442

R441

CB412

CB411

CB410

C40

5

C404

R422

R421

U403

Q402

Q401

R412

C40

6

R42

0

R414

R418

R41

7R416

R415

R410

R409

CB407

CB403

R407

U402

R406

R405

CB406

CB404

R305

R30

6

R308

R309

R315 R316

R318

R319

R522

R301

R311

R341

R340

R321

R322

R22

0R221

R533

R323 R34

3

CB301CB302

CB512

CB513

CB515

CB516

CB51

7

CB518

CB519

R537

R307

R317

R53

8

R534

R51

3

R535

R536

C515

R511

R512

R510

Q502

Q504

Q50

3

X702

X704

X701

U301 U302

R302

R34

2

CB303

CB304

CB305

CB306

CB307

CB308

R303

R304

R338

R330

R331

R358

R350

R351

U303U304

R33

2

R334

R33

3

R352

R35

3

R320

CB2

01

R209

CB510

R520

D503

R505

R504

C510

R502

R506

Q505

Q501

D501

C512

C511

D502

R503

R23

9

R312

R436

R437

R438

R313

R373

R374

Q506

L503

C520

C521

C506CB506

U503

CB409

R386

C306




7.4 Layout with DimensioningThe following dimensions should be used for development of extension boards.

Figure 7-10 Dimensioning (mm)




Figure 7-11 Dimensioning (mil)

The dimensioning is valid for all TriBoards.

User Manual RevisionHistory-1 V1.2 TriBoard TC3X4L TH V1.0 and TriBoard TC3X4L V1.0 2019-09


Revision History

Page or Item Subjects (major changes since previous revision)

V1.2, 2019-09

Table 5-6 correct Short name and Description for SDO from TLF35584

chapter 3.10 add description for LIN master and slave changes

Revision History add complete history of all previous versions

V1.1, 2019-06

all add TC364 in LQFP package as usable device and adapt description for this devices

chapter 3 add detailed description of usable devices/restricted devices

V1.0, 2017-11

First version

Trademarks of Infineon Technologies AGµHVIC™, µIPM™, µPFC™, AU-ConvertIR™, AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolDP™, CoolGaN™, COOLiR™, CoolMOS™, CoolSET™, CoolSiC™,DAVE™, DI-POL™, DirectFET™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, GaNpowIR™,HEXFET™, HITFET™, HybridPACK™, iMOTION™, IRAM™, ISOFACE™, IsoPACK™, LEDrivIR™, LITIX™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OPTIGA™,OptiMOS™, ORIGA™, PowIRaudio™, PowIRStage™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, SmartLEWIS™, SOLID FLASH™,SPOC™, StrongIRFET™, SupIRBuck™, TEMPFET™, TRENCHSTOP™, TriCore™, UHVIC™, XHP™, XMC™.

Trademarks updated November 2015

Other TrademarksAll referenced product or service names and trademarks are the property of their respective owners.

Edition 2019-09Published by Infineon Technologies AG81726 Munich, Germany

© 2019 Infineon Technologies AG.All Rights Reserved.

Do you have a question about any aspect of this document?Email: [email protected]

Document referenceDoc_Number

IMPORTANT NOTICEThe information given in this document shall in noevent be regarded as a guarantee of conditions orcharacteristics ("Beschaffenheitsgarantie"). With respect to any examples, hints or any typicalvalues stated herein and/or any information regardingthe application of the product, Infineon Technologieshereby disclaims any and all warranties and liabilitiesof any kind, including without limitation warranties ofnon-infringement of intellectual property rights of anythird party. In addition, any information given in this document issubject to customer's compliance with its obligationsstated in this document and any applicable legalrequirements, norms and standards concerningcustomer's products and any use of the product ofInfineon Technologies in customer's applications. The data contained in this document is exclusivelyintended for technically trained staff. It is theresponsibility of customer's technical departments toevaluate the suitability of the product for the intendedapplication and the completeness of the productinformation given in this document with respect tosuch application.

For further information on technology, delivery termsand conditions and prices, please contact the nearestInfineon Technologies Office (www.infineon.com).

WARNINGS

Due to technical requirements products may containdangerous substances. For information on the typesin question please contact your nearest InfineonTechnologies office.

Except as otherwise explicitly approved by InfineonTechnologies in a written document signed byauthorized representatives of Infineon Technologies,Infineon Technologies’ products may not be used inany applications where a failure of the product or anyconsequences of the use thereof can reasonably beexpected to result in personal injury.

Please read the Important Notice and Warnings at the end of this document

mailto:[email protected]

http://www.infineon.com

triboard manual tc3x4l v1 - infineon technologies

Documents