DESCRIPTION:

TRON FLEX a versatile membrane is based on acrylic

modified polymer it consists of a very elastic polymer with

the inherent flexibility that allows the membrane to

accommodate movements in the substrate. It works as a

seamless membrane that performs and adapt to any

construction requirements in varied climatic conditions.

TRON FLEX is water proofer and allows concrete surfaces to

breath water vapour naturally. It seals cracks and joints in

old or new roofs / walls and simultaneously leaving a

seamless finish to the roof surface. Due to its versatility, it

can be practically applied to any supported substrates like

concrete, asbestos cement.

RECOMMENDED:

?Waterproofing and protection

?Roofs, Balconies, Chajja

?Gutters

?Light roofing from metal or fibrous cement

?Gypsum and cement boards

?Perlite concrete, Foam Concrete

ADVANTAGES

?Waterproofing - prevents further ingression of

water in old and new concrete.

?Vapour permeability - allow vapour transmission to

release moisture.

?Durability - reinforced with fibre glass

matt increases film tensile

strength and wear resistance.

?Flexible - polymeric characterist ics

enable bridging of hairline

cracks and accommodate

minor joint movements.

?Weather Resistant - E xc e l l e n t r e s i s t a n c e t o

ultraviolet degradation.

?Traffic able - Able to withstand regular foot

traffic.

?Cost Effective - Repairs damaged concrete by

direct application without

additional reconstruction.

?Ease of application - Brush, roller or airless sprayappl ied. So lvent Free –operators do not need extrarespiratory protection.

?Recoating - After 5-7 years, recoating canbe done to the surfaceanother finish coat.

?Ease of Maintenance - fungus &mold are free onapply surfaces

PRODUCT PROPERTIES

COVERAGE

Specification for walls

The system consists of the following sequence;

1. 1 coat of Primer tron flex (0.1litre / m²)

2. 1 coat of TRON FLEX (0.3litre/m²)

3. 1 layer of Fibre mesh

4. 1 coat of TRON FLEX (0.3litre/m²)

5. Final 1 coat of TRON FLEX (0.3litre/m²)

The finished coating will approximately provide 0.8mm film

thickness.

NOTE:

?3 hours is needed for the drying of each coat of

TRON FLEX before the application of the next coat.

?Coverage and Thickness is theoretical and may vary due

to different substrates.

ADHERETRON COMPLETE CONCRETE PROTECTOR

MALAYSIAwww.adheretron.com.my | e-mail: sales@adheretron.com.my

AD

HE

RE

TR

ON

CO

MP

LE

TE

C

ON

CR

ET

E

PR

OT

EC

TO

RTRON FLEX

ADVANCED TECHNOLOGY ELASTOMERIC ACRYLIC WATERPROOF MEMBRANE

Colour White, Grey, Light Green

Polymer content 64%

Density 1.2kg/litre of fresh liquid membrane

Adhesion to Substrate (N/mm²) 1) Applied on concrete with fibreglass

2) Applied on concrete without fibreglass

1.1(ASTM D4541:2009) >6.0Mpa (Cohesive B) ASTM D4541

>6.0Mpa (Cohesive B) ASTM D4541

Water Vapour Transmission 27g/m² (AMST E96:2005)

Maximum Tensile Strength 4.6N/mm² (ASTM D412 – 2006a)

Elongation At Break 431% (ASTM D412 – 2006a)

Cracks Bridging (mm) No cracks was observed (ASTM C836:2006)

Weather resistance UV Resistant (ASTM G 53)

Solid content % 68.03% (ASTM 2369)

Durometer Hardness (Shore A) 53 (ASTM D2240-05)

APPLICATION WITH ADHERETRON FIBBER MESH

ADHERETRON Fibre mesh is a non-woven fibre mesh fabric

used as reinforcement in the application of liquid

waterproofing where substantial movement is anticipated.

It is designed so as to allow TRON FLEX to pass through;

thereby forming a compact reinforced sandwich

membrane upon application problem between the top and

bottom layers should a high force be applied on it.

APPLICATION FOR USING POLYESTER FIBRE MESH IS AS

FOLLOWS:

Where a layer of fibre mesh is used as reinforcement for

better tensile strength of membrane. It shall be laid onto

stthe 1 coat of TRON FLEX before it is totally dry to enable it

st ndto adhere onto the 1 coat and leave to dry. The 2 coat

TRON FLEX should apply.

APPLICATION INSTRUCTIONS

SURFACE PREPARATION

Ensure all surface are clean and free from dirt, oil, grease,

efflorescence, fungi growth, loose particles and laitance.

Hack off honeycombs to expose concrete. Remove all

chipped and loose particles and clean surface before

repairing.

Repair all hacked off areas with TRON INJECTION GROUT.

METHOD OF APPLICATION

?Surface preparation

Roofs and other surfaces must be thoroughly clean,

dry, free from dirt, oil, grease and loosely adhering

particles.

?Primary Coat

A primer is required prior to the application of TRON FLEX

onto porous surfaces such as asbestos cement and

reinforced concrete.

?TRON CRETE should be applied as a primer by brush at

coverage of 200 gms/m² and allowed to dry before

proceeding.

?The first coat of TRON FLEX is applied with roller up to a

thickness of 0.3mm. The second coat is applied after

24hours with roller to achieve a final thickness of 0.8

TRON FLEX final curing to take place at normal room

temperature. Complete curing is required before any

insulation or protection board is placed.

PACKAGING

TRON FLEX is an available in 5 & 20 lrt pail.

TECHNICAL SERVICE

The company will be pleased to offer any technical

assistance on specific applications.

Note: The information submitted in this publication is based our current knowledge

and experience. In view of the many factors that may affect processing and

application these data do not relieve processors of the responsibility of carrying out

their own tests and experiments neither do they imply any legally binding assurance

of certain properties or of suitability of specific purpose. It is the responsibility of

those whom we supply. Our products to ensure that any proprietary right and

existing laws and legislations are observed.

20 lrt & 5 lrt / PAIL MUST BE STORED IN DRY PLACE.

ADHERETRON COMPLETE CONCRETE PROTECTOR

MALAYSIAwww.adheretron.com.my | e-mail: sales@adheretron.com.my

AD

HE

RE

TR

ON

CO

MP

LE

TE

C

ON

CR

ET

E

PR

OT

EC

TO

RTRON FLEX

ADVANCED TECHNOLOGY ELASTOMERIC ACRYLIC WATERPROOF MEMBRANE