um1705 user manual - home - stmicroelectronics rev 2 5/17 um1705 description 16 1 description...
TRANSCRIPT
May 2015 DocID025678 Rev 2 1/17
1
UM1705User manual
Discovery kit for the M24SR series Dynamic NFC/RFID tag Premium and Standard Editions
Introduction
The M24SR-DISCOVERY is a demonstration kit to evaluate the features and capabilities ofthe M24SR series and is based on the M24SR64 device. Two versions of this kit areavailable: the Standard Edition and the Premium Edition.The Premium Edition includes all of the Standard edition features, plus a headset and aBluetooth module to demonstrate the convenience to pair it with a smartphone via NFC.The M24SR64 device is a dynamic NFC/RFID tag IC with a dual interface. It embeds a64 Kbits EEPROM memory. It can be operated from an I2C interface or by a 13.56 MHzRFID reader or an NFC phone.The I2C interface uses a two-wire serial interface, consisting of a bidirectional data line anda clock line. It behaves as a slave with respect to the I2C protocol.The RF protocol is compatible with ISO/IEC 14443 Type A and NFC Forum Type 4 Tag.The board is powered through the USB bus. It also includes a microcontroller STM32F103to drive the EEPROM via I2C and the LCD screen via SPI bus.The M24SR-DISCOVERY (MB1138) schematics, BOM, gerber files, drivers and firmware
can be downloaded from www.st.com.
Figure 1. M24SR-Discovery Board
www.st.com
Contents UM1705
2/17 DocID025678 Rev 2
Contents
1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Hardware and layout description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 M24SR-Discovery board description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 M24SR-Discovery board powering and startup . . . . . . . . . . . . . . . . . . . . . 9
3.3 Program and debug the M24SR-Discovery board . . . . . . . . . . . . . . . . . . . 9
3.4 Hardware implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Federal Communications Commission (FCC) and Industry Canada (IC) Compliance Statements 14
4.1 FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1.1 Part 2.1077 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1.2 Part 15.105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1.3 Part 15.21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2 IC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.2.1 Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.2.2 Déclaration de conformité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DocID025678 Rev 2 3/17
UM1705 List of tables
3
List of tables
Table 1. Device Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Table 2. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
List of figures UM1705
4/17 DocID025678 Rev 2
List of figures
Figure 1. M24SR-Discovery Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Figure 2. M24SR-Discovery board block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Figure 3. M24SR-Discovery board front layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Figure 4. M24SR-Discovery board back layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Figure 5. Discovery Kit M24SR (MCU & M24SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Figure 6. Discovery Kit M24SR(LCD Screen) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Figure 7. Discovery Kit M24SR (BT Module) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Figure 8. BOM (Bill Of Material) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DocID025678 Rev 2 5/17
UM1705 Description
16
1 Description
Standard and premium editions of M24SRXX-Y family’s discovery kit (M24SR-DISCOVERY) are discovery kits meant to evaluate the features and capabilities of the M24SRxx-Y products. They come with application notes, I2C drivers for M24SR, BOM board schematics, gerber files, firmware schematics which help reduce design effort and can be downloaded at www.st.com.The features of Standard Edition are the M24SR64 IC (64-Kbit), a 30x31mm NFC antenna, a 2.4”QVGA LCD display, a Micro USB connector, the STM32F103 MCU, a JTAG connector for possible firmware upgrades, a Joystick and a reset button. The board is powered through the USB bus. It also includes a microcontroller STM32F103 to drive the EEPROM via I2C and the LCD screen via SPI bus.The Premium Edition includes all of the features of the standard edition plus a headset and a Bluetooth module which demonstrates the ease of pairing a smartphone to the kit over NFC. The Bluetooth module is driven by the STM32F103 microcontroller via UART link.The Figure 2 shows the M24SR-Discovery board block diagram.
Figure 2. M24SR-Discovery board block diagram
*Available only on premium edition.
Features UM1705
6/17 DocID025678 Rev 2
2 Features
Ready-to-use printed circuit board (PCB) including
• M24SR64-Y Dynamic NFC/RFID tag.
• 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
• STM32F103RGT6 64LQFP 32-bit microcontroller, with 1Mbytes of Flash memory
• LCD Color Screen (320*200 pixels)
• Different color LEDs
• USB micro-B connector for board powering
• JTAG connector for microcontroller firmware upgrade and debug
• Joystick for menu selection
• Bluetooth module with audio outputs connected to Jack 3.5(a)
• Headset(a)
a. Available with the Premium edition only: M24SRDISCO-PREM
Table 1. Device Summary
Reference Order Code
M24SR-DISCOVERY M24SR-DISCO-STDM24SR-DISCO-PREM
DocID025678 Rev 2 7/17
UM1705 Hardware and layout description
16
3 Hardware and layout description
The M24SR-DISCO board contains the M24SR64-Y chip. It is a dynamic NFC/RFID tag IC. It features a 64 Kbits of EEPROM memory, preformatted for NFC transactions, and which can be protected by a unique and flexible 128-bit password scheme. The memory bank can be accessed by any of its to interfaces, either from an I2C interface or by a 13.56 MHz passive NFC interface. The I2C interface uses a two-wire serial interface, consisting of a bidirectional data line and a clock line. It behaves as a slave in the I2C protocol. The NFC interface is based on the ISO/IEC 14443 Type A and NFC Forum Type 4 Tag specifications. Because it is a passive RF interface, it operates when the board is powered but also when the board is unpowered. Two control pins are also available from the M24SR64-Y chip, allowing flexible management of the NFC interface.
3.1 M24SR-Discovery board description
The following figures show:
• M24SR-Discovery board front layout
• M24SR-Discovery board back layout
Hardware and layout description UM1705
8/17 DocID025678 Rev 2
Figure 3. M24SR-Discovery board front layout
*Available only on premium edition.
Figure 4. M24SR-Discovery board back layout
*Available only on premium edition.
DocID025678 Rev 2 9/17
UM1705 Hardware and layout description
16
3.2 M24SR-Discovery board powering and startup
The M24SR-Discovery board is powered by the USB bus via a Type A / micro B USB cable connected to a PC.
When powered up, the microcontroller starts the firmware already downloaded in the Flash memory. This is a demonstration of the different capability of the M24SR64 (RF on/off, change Vcard message, etc ). There is no modification or configuration to be done on the board to run the demo. Please refer to the firmware user manual available on ST web site www.st.com to get more detail.
3.3 Program and debug the M24SR-Discovery board
In order to flash or debug an STM32 microcontroller application on the M24SR-Discovery board, simply connect the 20-pin JTAG/SWD flat ribbon of the STLINK/V2 in-circuit debugger and programmer to the discovery kit board JTAG connector (J2).
Launch STLink Utility PC software. STM32F103RGT6 is part of the STM32F10x XL-density family.
(It can be downloaded from ST web site: www.st.com)
For more information or documentation on the STLINK/V2 in-circuit debugger and programmer, please visit www.st.com.
3.4 Hardware implementation
The Figure 5, Figure 6 and Figure 7 show the M24SR-Discovery Schematics (board reference MB1138).
The Figure 8 shows the Premium Bill of Material (MB1138_B01_BOM_PREMIUM).
Hard
wa
re and
lay
ou
t des
crip
tion
UM
170
5
10/1
7D
ocID025
678 Re
v 2
Figure 5. Discovery Kit M24SR (MCU & M24SR)
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
1
STMicroelectronics
MMY Division
3
Discovery Kit M24SR (MCU & M24SR)MB1138 B-01
02/12/2013
Title:
Size: Reference:
Date: Sheet: of
C�
Revision:
USB_DMUSB_DPJTMS
JTDO/JTRST
20pF
C4
SW1
/RESET
100nFC8
742792042L1
3.3V
3.3V
BLM18AG601SN1D
L2
742792641L3U5V
1
4
2
3
FL1
744232090
Q2BC817
Q1BC817
U5V
3.3V3.3V
USB_DMUSB_DP
11
22
33
ST1
USB_Disconnect
11 2 2
33 4 4
55 6 6
77 8 8
99 10 10
1111 12 12
1313 14 14
1515 16 16
1717 18 18
1919 20 20
J2
3.3V
/JTRSTJTDIJTMSJTCK
JTDO/RESET
1
4
2
3
FL2
744232222
742792042
L5
742792042
L6
U5V3.3V
2,2uF+ C24
10μF+ C16
VDD
MIRE1
MIRE
MIRE2
MIRE
MIRE3
MIRE
Vin1
GND
3
Vout 2
U4KF33BDT
JTCKJTDI
USB_Disconnect
Y18MHz
20pF
C1
3.3V
3.3V
VDD1
COMMON5
Selection2
DOWN3
LEFT1
RIGHT4
UP6
U2
MT008-A
JOY_SEL
JOY_UP
JOY_LEFTJOY_DOWN
JOY_RIGHT
JOY_UP
JOY_DOWN
JOY_RIGHT
JOY_SEL
BOOT060
NRST7
OSC_IN/PD05
OSC_OUT/PD16
PA0-WKUP14
PA115
PA216
PA317
PA420
PA521
PA622
PA723
PA841
PA942
PA1043
PA1144
PA1245
PA13/JTMS/SWDIO46
PA14/JTCK/SWCLK49
PA15/JTDI50
PB0 26
PB1 27
PB2/BOOT1 28
PB3/JTDO 55
PB4/JNTRST 56
PB5 57
PB6 58
PB7 59
PB8 61
PB9 62
PB10 29
PB11 30
PB12 33
PB13 34
PB14 35
PB15 36
PC0 8
PC1 9
PC2 10
PC3 11
PC4 24
PC5 25
PC6 37
PC7 38
PC8 39
PC9 40
PC10 51
PC11 52
PC12 53
PC13-TAMPER-RTC 2
PC14-OSC32_IN 3
PC15-OSC32_OUT 4
PD254
VBAT1
VDD_132
VDD_248
VDD_364
VDD_419
VDDA13
VSS_1 31
VSS_2 47
VSS_3 63
VSS_4 18
VSSA 12
U1
STM32F103RGT6100nF
C12
100nF
C13
100nF
C14
100nF
C15
100nFC11
100nF
C17
100nFC25100nF
C23
1MR2
10kR13
10k
R4
10
R1
0
R31
0
R32
10R19
10R21
1MR24
36kR25
10kR22
47kR23
1.5k
R26
10kR27
10kR29
10kR28
10kR30
10kR33
10kR35
10kR34
10kR36
3.3V10kR3 100nF
C2JOY_UP
10kR5 100nFC3
10kR6 100nFC5
10kR7 100nFC6
10kR12 100nFC7
JOY_LEFT
JOY_DOWN
JOY_RIGHT
JOY_SEL
JOY_LEFT
4,7nF
C22
3.3V
/LCD_CS
TE_Output
/LCD_DC
LCD_CLK
LCD_SDA
/RESET
BT_GPIO1
STM32_TX
STM32_RX
BT_POWER_ON
Signals to/from BT Module
Signals to/from LCD Screen
/RESET
BT_GPIO1
STM32_TX
STM32_RX
BT_POWER_ON
LCD_SDA
LCD_CLK
/LCD_DC
TE_Output
/LCD_CS
NC
C9
NC
C10
0R14
0R15
M24SR_SDAM24SR_SCL
M24SR_RF disable
GND
GND
GND
3.3V
M24SR_GPO
100nF
C20
100pF
C21
742792042
L43.3V
1μF
+ C19
M24SR_SCLM24SR_SDA
M24SR_GPO
LCD_SDA
LCD_CLK
/LCD_DCTE_Output
/LCD_CS
BT_GPIO1
STM32_TXSTM32_RX
BT_POWER_ON
M24SR_RF disable
LED1
1kR8
LED2
180R9
LED3
1kR10
LED4
560R11
30kR20
4k7R16
4k7R17
20kR18
RF disable 1AC0 2AC1 3VSS 4SDA5
SCL6
GPO7
VCC8
U3
M24SR64-YMN6T/2
NC
C18
0R79
11ST2
1 TP1
1 TP2
1 TP3
1 TP4
1 TP5
1 TP6
1 TP7
11ST3
AC1
AC0
Antenna1
MIRE4
MIRE
MIRE5
MIRE
MIRE6
MIRE
VBUS 1
DM 2
DP 3
ID 4
GND 5
Shield 6USB
_Micro-A
B re
ceptacle
J1
USB-MICRO-AB
BT_RESET BT_RESET
BT_RESET
UM
17
05H
ard
wa
re an
d la
yo
ut d
esc
riptio
n
DocID
025678 R
ev 2
11/17
Figure 6. Discovery Kit M24SR(LCD Screen)
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
D D
C C
B B
A A
2
ST Microelectronics
MMY Division
3
Discovery Kit M24SR (LCD Screen)MB1138 B-01
02/12/2013
Title:
Size: Reference:
Date: Sheet: of
A3�
Revision:
/LCD_CS
TE_Output
LCD_CLK/LCD_DC
LCD_SDA
/RESET
IM0IM1IM2IM3
IM[0..3] = 0110 --> 4-wire 8-bit serial I, SDA:In/Out
4K7R68
4K7R69
NCR67
NCR70
NCR76
NCR77
4K7R75
4K7R78
4K7R62
4K7R63
4K7R64
4K7R66
0R740R730R720R71
4.7μF+ C36
3.3V
3.3V
3.3V
/LCD_CS
TE_Output
/LCD_DCLCD_CLKLCD_SDA
/RESET
4K7R65
100nF
C35
ENABLE32
DOTCLK31
HSYNC33
VSYNC34
CSX38
DCX/SCL37
TE11
WRX/DCX36
RDX35
RESET39
DB0/B0 29
DB1/B1 28
DB2/B2 27
DB3/B3 26
DB4/B4 25
DB5/B5 24
DB6/G0 23
DB7/G1 22
VDD3_P(nc) 8
BC_CTRL(nc) 9
BC(nc) 10
VDD37
IM3 43IM2 42IM1 41IM0 40
SDA30
VCI6
LEDA44
LEDK145
LEDK246
LEDK347
LEDK448
YD3
XL2
YU1
XR4 GND 5
DB8/G2 21
DB9/G3 20
DB10/G4 19
DB11/G5 18
DB12/R0 17
DB13/R1 16
DB14/R2 15
DB15/R3 14
DB16/R4 13
DB17/R5 12
U7
SF-TC240T-9370-T
Hard
wa
re and
lay
ou
t des
crip
tion
UM
170
5
12/1
7D
ocID025
678 Re
v 2
Figure 7. Discovery Kit M24SR (BT Module)
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
D D
C C
B B
A A
3
ST Microelectronics
MMY Division
3
Discovery Kit M24SR (BT Module)MB1138 B-01
02/12/2013
Title:
Size: Reference:
Date: Sheet: of
A3�
Revision:
STM32_TXSTM32_RX
POWER_ON
100nFC27 10μF
+ C26
3.3V
GND AGND
GND10kR41
3.3V
2.2k
R513.3V
BT_POWER_ON
STM32_TXSTM32_RX
0R48
0R47
10kR44
3.3V10k
R54
VDD_PIO_ENBT_GPIO1
10kR50
GND
0R52
100nFC28
POWER_ON1
GND
2
GND
3
GND
4
AIO05
AIO16
PIO07
PIO18
PIO29
PIO310
USB_DN11
USB_DP12
PIO913
PIO1014
UART_RX15
UART_TX16
VDD_P
IO17
GND
18
RESET19
UART_RTS20
UART_CTS21
PIO822 PIO723 PIO624 PIO525 PIO426
PCM_IN 27PCM_OUT 28PCM_SYNC 29PCM_CLK 30GND
31SPI_CS# 32SPI_CLK 33SPI_MISO 34SPI_MOSI 35
LED0 36
VBAT
37
VDD_C
HG
38AGND
39
MIC_BIAS 40
MIC_B_P 41MIC_B_N 42
AGND
43
MIC_A_P 44MIC_A_N 45
SPKR_B_N 46SPKR_B_P 47
AGND
48
SPKR_A_N 49SPKR_A_P 50
U5
BTM760 (BT Module)
33
66
44
22
CN1
PJ3028B-3
2,2uF
+
C29
2,2uF
+
C30
3.9k
R53
3.9k
R55
3.9k
R49
3.9kR57
220μF
+
C31
2,2uF
+
C342,2uF
+
C33
3.9k
R60
3.9k
R59
3.9k
R61
3.9kR58 220μF
+
C32
Left_PLeft_NRight_PRight_N
Left_P
Left_N
Right_P
Right_N
OUT1 1
OUT2 7
VIN-12
VIN+13
VIN+25
VIN-26
GND
4VCC
8
U6
TS482ID
3.3V_A
AGND
LED5
100kR80
100kR81
3.3V_A
AGND
AGND
100nF
C38
BT_RESET RESET
3.3V
AGND
2,2uF+ C37
AGND
AGND
AGND
1μF
+ C39NCR38
GND
GND AGND
0
R37
742792042
L73.3V
3.3V_A
UM
17
05H
ard
wa
re an
d la
yo
ut d
esc
riptio
n
DocID
025678 R
ev 2
13/17
Figure 8. BOM (Bill Of Material)�������� �� ������ �� �� � ���� ������ ��������� �� �� ��� ��������� �� �� ��� ��� ����� � � ���� ������� ���������� ���� ����� ��!��"�#� ���� "�##���
� �"$�%��&'(����&��)*�!�+,)������(�%���-%�.(+ $� )���+,/�-0�- �(��� � �� ����� �(�%���-%�.(+ �(� 1��������,��� ���������� ���2� �3���� ������ ���(--45*�� $� 1�6�('"7/�(5--4* 2� �3���� ������ � �(--45*� '�"89�"�::��������,��+,56�9+(8� $% ��,��+,56�9+(8� �(��� � �� ����� ��,��+,56�9+(8� �(� %;%���� ���� �� ��� ��7�%%&( $, �*7 �(��� � �� ����� 7�%%&( �(� & �(���3����� ��&(�<+- $= &(�<+- �������(�3�� ��� &(�<+-� *�����*#� ��� ��(�,4�'( $+ ��49 �(��� � �� ����� (�,4�'( �(� )"��� �����5("�,-(5>%<-*5( $< ��5("�,-(5,4�5-< ����(�3�� ��� ��5("�,-(5>%<-*5(
� "�9:9�*(:$���)""�-+-%�9�-�=-���?��9" "�4 -+-% 9 ������� ���� ��� �@��� "�9:9�*(:$���)""�-+-%�9�-�=-��=?�9" ">A�"�- -+-% 9� "�9:9�*(:$���)""�-+-%�9�-�=-��=?���-�� "�A�", -+-% �� � �4,,�<�� "�9:9�*(:$���)""�-+-%�9�-�=-��=?���--�� "�� -+-% �� � ,>>���� "�9:9�*(:$���)""�-+-%�9�-�=-��=?��,A<�� "�� -+-% �� � �4%%4+>
�> "�9:9�*(:$���)""�-+-%�9�-�=-��=?���--�� "�A�"%A�"=A�"+A�"<A�"4A�"��A�"��A�"�%A�"�,A�"�=A�"�<A�"�-A�"�%A�"�=A�"�<A�"�4A�"%=A�"%4 -+-% �� � �<,-+��� �>%�(*9(*)������)�"*�������+���-?�&���� �*���B� "�>A�"%> �>%5* �� � �<=,�<,+ �>%�(*9(*)������)�"*���A����%=���-?�&���� �"���A��� "�,A�"�>A�"%-A�"%%A�"%,A�"%< �>%5" �� � �<=,��4� �>%�(*9(*)������)�"*��,A<����+���-?�&���� �*��,;<B� "%+ �>%5* �� � �<=,�<,� �>%�(*9(*)������)�"*���-���%=���-?������ ����-B� "�+A�"�+ �>%5 �� � ����>,>� �>%�(*9(*)������)�"*����-���+;%���-?�&���� �"����-B� "%�A�"%� �>%5" �� � �%=%-+-
�% ���������"���-+-%�-A�2�=?��- ��,A���=A��%�A��%�A��%<A��,<A��,4A��=�A��<�A��<�A��<%A��<,A��<> -+-%% ���������"���-+-%�-A�2�=?���- ��A���>A���� -+-%� ���������"���-+-%�-A�2�=?���4- �> -+-%� ���������"���-+-%�-A�2�=?��=+- ��� -+-%� ���������"���-+-%�-A�2�=?���� �4A���- -+-%� ���������"���-+-%�-A�2�=?���;=� ��+ -+-%� ���������"���-+-%�-A�2�=?���;�� �=� -+-%4 ���������"���-+-%�-A�2�=?��%;>� �,>A��=%A��==A��=<A��=4A��=>A��+-A��+� -+-%
�� ���������"���-+-%�-A�2�=?��,7< ��+A���<A�+�A��+%A��+,A��+=A��++A��+4A��+>A��<=A��<4 -+-%�- ���������"���-+-%�-A�2�=?���-� �%A��,A��=A��+A��<A����A���%A����A���<A���4A���>A��%-A��%%A��%,A��%=A��%+A��,�A��,,A��=-A��=, -+-%� ���������"���-+-%�-A�2�=?���-� ��4 -+-%� ���������"���-+-%�-A�2�=?��%-� ��- -+-%� ���������"���-+-%�-A�2�=?��%+� ��= -+-%� ���������"���-+-%�-A�2�=?��,<� ��% -+-%� ���������"���-+-%�-A�2�=?���--� �4-A��4� -+-%� ���������"���-+-%�-A�2�=?���� ��A���, -+-%= ���������"���-+-%�-A�2�=?��9" �%4A��+<A��<-A��<+A��<< -+-% 9
� �:��'(:�&:*A�-;%4�!�A�=--�*A�-+-%��&)��4*.+-��9� )� -+-% �$�*(* &)��4*.+-��9� �� � �=�=+<> ������� ���� ��� �@��� �:��'(:�"���%--�!�;�-+-%��<,�<>�+,� )% -+-% 2$�(!�:):7(��9'7 <,�<>�+,� �� � �+%=<-= ������� ���� ��� �@��= �:��'(:�"���+--�!�;�-4-=��<,�<>�-,� )�A�),A�)=A�)+A�)< -4-= 2$�(!�:):7(��9'7 <,�<>�-,� �� � �+%=<�+ ������� ���� ��� �@��� 9�'�:��$���:�����"����;�7�!�;�-;,*��<,,�%���� �)� <,,�%�000 2$�(!�:):7(��9'7 <,,�%���� �� � �+%+,4� ������� ���� ��� �@��� 9�'�:��$���:�����"���>-�!�;�%<-�*��<,,�%�->- �)� <,,�%�000 2$�(!�:):7(��9'7 <,,�%�->- �� � �+%+,<, ������� ���� ��� �@��
� &"4�<5�+�5�(�*9�'�(���9�9�-;=*�,=����(�%��&"4�< ��A��� ��(�% �$)('"��� &"4�<5�+ �� � �<>4-<<� ):A���-+A�&)$:��& ��)� ):% ):5��-+ '*)'.!( =>44�>��-<� �� � ���%>=%� ):A���-+A�.�::9��. ��)� ):� ):5��-+ '*)'.!( =>44�<-�-<� �� � �,++---� ):A���-+A��:�����)� ):�A�):= ):5��-+ '*)'.!( =>44��-�-<� �� � �,+=>><� ):A���-+A�6:))�2��6 �@�)� ):, ):5��-+ '*)'.!( =>44�,-�-<� �� � �,+=>>4� ���"�6�(*)����"'))*(��A4�A�-��A�-��#��4�!C 6� !",>� ��D�:):"(��9'"� ��D�)�8-4-5�- �� � �-+%><�
� "������ ���(�� �(�A��(% "�9/��(� �"' <<%��5,-�5%+)� �� � �-><>=, 9� "������ �%�(��� �(� "�9/%�(�/��;=, �"' <<%��5,-�5%+)� �� � �-><>=, 9� !:*:�A��'.!(�*9.):A��-2*6�� 1� !:�-/�-�(�/�/"�$: �$)('"��� �">*��5�-%, �� � �->>�,4� ��� ��$�&�(���*&�"������ 1� $�&5�'"��5*& ��):D� ,<=>-5---�� ���3�&��������2/&�/�( �2� ���,1��* *)"��2'("! ���,1��* ������� ("5-%D.5+;- �� � %4-�%-=� 1����%;=���1%-�4&5% "9� �15%-�4& ����� �1%-�4&5%
��� �"&��%-##�0�+-##�0�;+##�E��� ����A���#�������������3�����A�& ��"� � F= &�#����� �����G�� ������ !*���9 �,��(=") �� � �4<+=�- #������3��3 ��3������" ���� �6�� & ��1���������������3����� �$�
��� (���� ��������� !����� & ��� �E� #��#�:������F� '�� ��"� ��E� #��#�:������F� ���� ����#� ��E��� �H��� ��"� �H!����H& ��� F
Federal Communications Commission (FCC) and Industry Canada (IC) Compliance Statements
14/17 DocID025678 Rev 2
4 Federal Communications Commission (FCC) and Industry Canada (IC) Compliance Statements
4.1 FCC Compliance Statement
4.1.1 Part 2.1077
STMicroelectronics Part No. M24SR-Discovery
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For purposes of FCC Rule 2.909, the Responsible Party is STMicroelectronics Inc., located at 750 Canyon Drive, Suite 300, Coppell, TX 75019, USA, with telephone number (972) 466-6000.
4.1.2 Part 15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference's by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
4.1.3 Part 15.21
Any changes or modifications to this equipment not expressly approved by STMicroelectronics may cause harmful interference and void the user’s authority to operate this equipment.
DocID025678 Rev 2 15/17
UM1705Federal Communications Commission (FCC) and Industry Canada (IC) Compliance State-
16
4.2 IC Compliance Statement
4.2.1 Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation.
4.2.2 Déclaration de conformité
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Revision history UM1705
16/17 DocID025678 Rev 2
5 Revision history
Table 2. Document revision history
Date Revision Changes
04-Feb-2014 1 Initial Release
07-May-2015 2
Added Section 4: Federal Communications Commission (FCC) and Industry Canada (IC) Compliance Statements
Updated Figure 2: M24SR-Discovery board block diagram, Figure 3: M24SR-Discovery board front layout and Figure 4: M24SR-Discovery board back layout
DocID025678 Rev 2 17/17
UM1705
17
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2015 STMicroelectronics – All rights reserved