universal expansion joints - hyspan · nom size unit type unit style design press. lateral movement...
TRANSCRIPT
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
3"Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
3 U O 300 4.02 WS WS L 32" B2 E2
SETARGNIRPS&STNEMEVOM)ni/sbl()sehcni()ni/sbl()sehcni(
LASREVINUHTGNEL
NIATBOOTHTGNELLASREVINUOTDDA)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
15.3 01 66.1 081 00.21 00.4 05.4
00.6 01 66.1 081 00.81 00.4 05.4
75.8 01< 66.1 081 00.42 00.4 05.4
07.11 07.31 01< 66.1 081 00.63 00.4 05.4
05gisp
24.2 02 90.1 052 00.21 00.4 05.4
60.4 01 90.1 052 00.81 00.4 05.4
27.5 01< 90.1 052 00.42 00.4 05.4
78.11 60.9 01< 90.1 052 00.63 00.4 05.4
051gisp
64.2 04 71.1 074 00.21 00.4 05.4
12.4 01 71.1 074 00.81 00.4 05.4
99.5 01 71.1 074 00.42 00.4 05.4
49.11 85.9 01< 71.1 074 00.63
)PV&PF(ETALPEGNALF
526.0
526.0
526.0
526.0
526.0
526.0
526.0
526.0
526.0
526.0
526.0
526.0 00.4 05.4
003gisp
86.1 09 87.0 0611 00.21 00.4 05.4
48.2 03 87.0 0611 00.81 00.4 05.4
20.4 02 87.0 0611 00.42 00.4 05.4
99.11 93.6 01 87.0 0611 00.63
)RV&RF(DEGROFEGNALF
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5786.1
5786.1
5786.1
5786.1 00.4 05.4
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 5/8" thick; 150# ANSI B16.5 drilling (A-36).Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If forged flanged ends are specified, the maximum temperature rating for150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT =TIE RODS/LIMIT RODS
CONTROL RODSH = HINGEG = GIMBAL
39
Flow
40
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
27.2 02 66.1 051 00.21 00.4 00.6
66.4 01 66.1 051 00.81 00.4 00.6
36.6 01< 66.1 051 00.42 00.4 00.6
25.91 16.01 01< 66.1 051 00.63 00.4 00.6
05gisp
00.2 04 25.1 082 00.21 00.4 00.6
00.4 01 25.1 082 00.81 00.4 00.6
49.5 01 25.1 082 00.42 00.4 00.6
62.02 05.9 01< 25.1 082 00.63 00.4 00.6
051gisp
19.1 06 92.1 054 00.21 00.4 00.6
83.3 02 92.1 054 00.81 00.4 00.6
78.4 01 92.1 054 00.42 00.4 00.6
92.02 09.7 01 92.1 054 00.63
)PV&PF(ETALPEGNALF
526.0
526.0
526.0
526.0
526.0
526.0
526.0
526.0
526.0
526.0
526.0
526.0 00.4 00.6
003gisp
05.1 052 20.1 0371 00.21 00.4 00.6
56.2 09 20.1 0371 00.81 00.4 00.6
38.3 05 20.1 0371 00.42 00.4 00.6
15.02 12.6 02 20.1 0371 00.63
)RV&RF(DEGROFEGNALF
5213.1
5213.1
5213.1
5213.1
5213.1
5213.1
5213.1
5213.1
5213.1
5213.1
5213.1
5213.1
578.1
578.1
578.1
578.1 00.4 00.6
4 D O 050 1.52 FP FP 191/4"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 5/8" thick; 150# ANSI B16.5 drilling (A-36).Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If forged flanged ends are specified, the maximum temperature rating for150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
4"
TOTALAXIAL
COMPRESSION
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
41
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
5 U T 150 7.41 FR FR 387/8"
SETARGNIRPS&STNEMEVOM)ni/sbl()sehcni()ni/sbl()sehcni(
LASREVINUHTGNEL
NIATBOOTHTGNELLASREVINUOTDDA)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
06.2 04 82.2 061 00.21 00.4 05.7
07.4 01 82.2 061 00.81 00.4 05.7
68.6 01 82.2 061 00.42 00.4 05.7
66.92 52.11 01< 82.2 061 00.63 00.4 05.7
05gisp
00.2 09 87.1 004 00.21 00.4 05.7
36.3 03 87.1 004 00.81 00.4 05.7
13.5 02 87.1 004 00.42 00.4 05.7
62.03 07.8 01 87.1 004 00.63 00.4 05.7
051gisp
06.1 051 65.1 095 00.21 00.4 05.7
99.2 05 65.1 095 00.81 00.4 05.7
54.4 03 65.1 095 00.42 00.4 05.7
03.03 14.7 01 65.1 095 00.63
)PV&PF(ETALPEGNALF
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0 00.4 05.7
003gisp
24.1 053 72.1 0351 00.21 00.4 05.7
75.2 031 72.1 0351 00.81 00.4 05.7
67.3 07 72.1 0351 00.42 00.4 05.7
45.03 61.6 03 72.1 0351 00.63
)RV&RF(DEGROFEGNALF
5734.1
5734.1
5734.1
5734.1
5734.1
5734.1
5734.1
5734.1
5734.1
5734.1
5734.1
5734.1
00.2
00.2
00.2
00.2 00.4 05.7
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 3/4" thick; 150# ANSI B16.5 drilling (A-36).Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If forged flanged ends are specified, the maximum temperature rating for150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
5"
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
42
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
12.2 06 82.2 081 00.21 00.5 00.9
10.4 02 82.2 081 00.81 00.5 00.9
58.5 01 82.2 081 00.42 00.5 00.9
08.04 06.9 01< 82.2 081 00.63 00.5 00.9
05gisp
66.1 051 37.1 074 00.21 00.5 00.9
00.3 05 37.1 074 00.81 00.5 00.9
04.4 03 37.1 074 00.42 00.5 00.9
15.14 12.7 01 37.1 074 00.63 00.5 00.9
051gisp
43.1 042 35.1 007 00.21 00.5 00.9
15.2 09 35.1 007 00.81 00.5 00.9
37.3 04 35.1 007 00.42 00.5 00.9
65.14 22.6 02 35.1 007 00.63
P)V&PF(ETALPEGNALF
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0 00.5 00.9
003gisp
99.0 065 42.1 0741 00.21 00.5 00.9
19.1 091 42.1 0741 00.81 00.5 00.9
98.2 001 42.1 0741 00.42 00.5 00.9
56.14 88.4 04 42.1 0741 00.63
)RV&RF(DEGROFEGNALF
5265.1
5265.1
5265.1
5265.1
5265.1
5265.1
5265.1
5265.1
5265.1
5265.1
5265.1
5265.1
5260.2
5260.2
5260.2
5260.2 00.5 00.9
6 U T 300 1.91 FR EL 291/16"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 3/4" thick; 150# ANSI B16.5 drilling (A-36).Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If forged flanged ends are specified, the maximum temperature rating for150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
6"
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
43
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
8 U T 150 2.16 VP VP 20"
SETARGNIRPS&STNEMEVOM)ni/sbl()sehcni()ni/sbl()sehcni(
LASREVINUHTGNEL
NIATBOOTHTGNELLASREVINUOTDDA)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
65.1 09 09.1 081 00.21 00.6 00.21
37.2 03 09.1 081 00.81 00.6 00.21
39.3 02 09.1 081 00.42 00.6 00.21
58.86 43.6 01 09.1 081 00.63 00.6 00.21
05gisp
38.1 071 58.2 082 00.21 00.6 00.21
00.3 06 58.2 082 00.81 00.6 00.21
00.5 03 58.2 082 00.42 00.6 00.21
52.07 57.8 01 58.2 082 00.63 00.6 00.21
051gisp
00.1 096 29.1 099 00.21 00.6 00.21
61.2 032 29.1 099 00.81 00.6 00.21
03.3 011 29.1 099 00.42 00.6 00.21
34.07 56.5 04 29.1 099 00.63
)PV&PF(ETALPEGNALF
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1 00.6 00.21
003gisp
00.1 0251 70.2 0391 00.21 00.6 00.21
41.2 094 70.2 0391 00.81 00.6 00.21
53.3 042 70.2 0391 00.42 00.6 00.21
09.07 58.5 09 70.2 0391 00.63 00.6 00.21
)RV&RF(DEGROFEGNALF
57.1
57.1
57.1
57.1
57.1
57.1
57.1
57.1
57.1
57.1
57.1
57.1
5734.2
5734.2
5734.2
57342.
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 1" thick; 150# ANSI B16.5 drilling (A-36).Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If forged flanged ends are specified, the maximum temperature rating for150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges..• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
8"
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
44
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
14.1 031 73.2 071 00.21 00.6 00.51
85.2 05 73.2 071 00.81 00.6 00.51
87.3 03 73.2 071 00.42 00.6 00.51
76.301 22.6 01 73.2 071 00.63 00.6 00.51
05gisp
00.1 035 37.2 015 00.21 00.6 00.51
15.2 081 37.2 015 00.81 00.6 00.51
48.3 09 37.2 015 00.42 00.6 00.51
44.501 85.6 03 37.2 015 00.63 00.6 00.51
051gisp
78.0 0821 88.1 0321 00.21 00.6 00.51
37.1 034 88.1 0321 00.81 00.6 00.51
56.2 012 88.1 0321 00.42 00.6 00.51
85.501 45.4 08 88.1 0321 00.63
)PV&PF(ETALPEGNALF
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1 00.6 00.51
003gisp
29.0 0332 99.1 0022 00.21 00.6 00.51
28.1 087 99.1 0022 00.81 00.6 00.51
87.2 083 99.1 0022 00.42 00.6 00.51
13.701 67.4 051 99.1 0022 00.63
)RV&RF(DEGROFEGNALF
5739.1
5739.1
5739.1
5739.1
5739.1
5739.1
5739.1
5739.1
5739.1
5739.1
5739.1
5739.1
526.2
526.2
526.2
526.2 00.6 00.51
10 U T 150 1.73 EL EL 48"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 1" thick; 150# ANSI B16.5 drilling (A-36).Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If forged flanged ends are specified, the maximum temperature rating for150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
10"
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
45
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
12 U O 300 1.93 WS WS 40"
SETARGNIRPS&STNEMEVOM)ni/sbl()sehcni()ni/sbl()sehcni(
LASREVINUHTGNEL
NIATBOOTHTGNELLASREVINUOTDDA)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)RV&RF(DEGROFEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
72.1 072 58.2 012 00.21 5781.2 00.8 00.81
24.2 09 58.2 012 00.81 5781.2 00.8 00.81
26.3 05 58.2 012 00.42 5781.2 00.8 00.81
56.541 70.6 02 58.2 012 00.63 5781.2 00.8 00.81
05gisp
00.1 086 41.3 064 00.21 5781.2 00.8 00.81
00.2 032 41.3 064 00.81 5781.2 00.8 00.81
96.3 011 41.3 064 00.42 5781.2 00.8 00.81
66.741 63.6 04 41.3 064 00.63 5781.2 00.8 00.81
051gisp
76.0 0023 67.1 0412 00.21 5781.2 00.8 00.81
53.1 0701 67.1 0412 00.81 5781.2 00.8 00.81
70.2 025 67.1 0412 00.42 5781.2 00.8 00.81
00.841 65.3 002 67.1 0412 00.63
)PV&PF(ETALPEGNALF
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.15781.2 00.8 00.81
003gisp
36.0 0427 56.1 0184 00.21 578.2 00.8 00.81
62.1 0142 56.1 0184 00.81 578.2 00.8 00.81
39.1 0811 56.1 0184 00.42 578.2 00.8 00.81
78.841 23.3 064 56.1 0184 00.63 578.2 00.8 00.81
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 1" thick; 150# ANSI B16.5 drilling (A-36).Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If forged flanged ends are specified, the maximum temperature rating for150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges..• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
12"
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
46
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
55.2 022 99.3 033 00.81 00.8 00.12
20.4 001 99.3 033 00.42 00.8 00.12
01.7 04 99.3 033 00.63 00.8 00.12
35.471 42.01 02 99.3 033 00.84 00.8 00.12
05gisp
00.2 082 36.3 034 00.81 00.8 00.12
56.3 031 36.3 034 00.42 00.8 00.12
44.6 05 36.3 034 00.63 00.8 00.12
18.571 92.9 03 36.3 034 00.84 00.8 00.12
051gisp
13.1 0231 24.2 0271 00.81 00.8 00.12
61.2 006 24.2 0271 00.42 00.8 00.12
79.3 022 24.2 0271 00.63 00.8 00.12
91.671 58.5 011 24.2 0271 00.84
)PV&PF(ETALPEGNALF
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1 00.8 00.12
003gisp
92.1 0082 64.2 0253 00.81 00.8 00.12
31.2 0721 64.2 0253 00.42 00.8 00.12
69.3 064 64.2 0253 00.63 00.8 00.12
31.771 58.5 032 64.2 0253 00.84
)RV&RF(DEGROFEGNALF
52.2
52.2
52.2
52.2
52.2
52.2
52.2
52.2
52.2
52.2
52.2
52.2
00.3
00.3
00.3
00.3 00.8 00.12
14 U O 150 2.16 FR FR L 281/2"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 1" thick; 150# ANSI B16.5 drilling (A-36).Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If forged flanged ends are specified, the maximum temperature rating for150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
14"
Flow
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
47
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
16 U T 050 3.00 FP FP 26"
SETARGNIRPS&STNEMEVOM)ni/sbl()sehcni()ni/sbl()sehcni(
LASREVINUHTGNEL
NIATBOOTHTGNELLASREVINUOTDDA)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
42.2 062 99.3 003 00.81 00.8 00.42
25.3 021 99.3 003 00.42 00.8 00.42
12.6 05 99.3 003 00.63 00.8 00.42
48.722 69.8 02 99.3 003 00.84 00.8 00.42
05gisp
49.1 056 19.3 086 00.81 00.8 00.42
00.3 003 19.3 086 00.42 00.8 00.42
37.5 011 19.3 086 00.63 00.8 00.42
91.132 93.8 06 19.3 086 00.84 00.8 00.42
051gisp
97.1 0141 16.3 0741 00.81 00.8 00.42
19.2 056 16.3 0741 00.42 00.8 00.42
82.5 042 16.3 0741 00.63 00.8 00.42
60.232 37.7 021 16.3 0741 00.84
)PV&PF(ETALPEGNALF
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1
00.1 00.8 00.42
003gisp
43.1 0382 07.2 0392 00.81 00.8 00.42
71.2 0131 07.2 0392 00.42 00.8 00.42
59.3 084 07.2 0392 00.63 00.8 00.42
94.232 87.5 052 07.2 0392 00.84
)RV&RF(DEGROFEGNALF
05.2
05.2
05.2
05.2
05.2
05.2
05.2
05.2
05.2
05.2
05.2
05.2
52.3
52.3
52.3
52.3 00.8 00.42
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 1" thick; 150# ANSI B16.5 drilling (A-36).Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If forged flanged ends are specified, the maximum temperature rating for150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
16"
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
48
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
00.2 053 99.3 033 00.81 00.8 00.72
51.3 071 99.3 033 00.42 00.8 00.72
65.5 06 99.3 033 00.63 00.8 00.72
94.482 20.8 03 99.3 033 00.84 00.8 00.72
05gisp
37.1 019 78.3 067 00.81 00.8 00.72
08.2 024 78.3 067 00.42 00.8 00.72
90.5 051 78.3 067 00.63 00.8 00.72
32.882 44.7 08 78.3 067 00.84 00.8 00.72
051gisp
35.1 0212 34.3 0871 00.81 00.8 00.72
74.2 089 34.3 0871 00.42 00.8 00.72
05.4 063 34.3 0871 00.63 00.8 00.72
62.882 85.6 081 34.3 0871 00.84
)PV&PF(ETALPEGNALF
5260.1
5260.1
5260.1
5260.1
5260.1
5260.1
5260.1
5260.1
5260.1
5260.1
5260.1
5260.1 00.8 00.72
003gisp
91.1 0593 86.2 0923 00.81 00.8 00.72
39.1 0381 86.2 0923 00.42 00.8 00.72
15.3 076 86.2 0923 00.63 00.8 00.72
86.982 31.5 043 86.2 0923 00.84
)RV&RF(DEGROFEGNALF
5786.2
5786.2
5786.2
5786.2
5786.2
5786.2
5786.2
5786.2
5786.2
5786.2
5786.2
5786.2
05.3
05.3
05.3
05.3 00.8 00.72
18 U T 050 2.80 FR EL 5311/16"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 11/16" thick; 150# ANSI B16.5 drilling (A-36).Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If forged flanged ends are specified, the maximum temperature rating for150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
18"
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
49
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
20 U T 150 2.65 FR FR 293/4"
SETARGNIRPS&STNEMEVOM)ni/sbl()sehcni()ni/sbl()sehcni(
LASREVINUHTGNEL
NIATBOOTHTGNELLASREVINUOTDDA)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
39.1 079 23.5 006 00.81 00.8 00.03
00.3 044 23.5 006 00.42 00.8 00.03
20.6 061 23.5 006 00.63 00.8 00.03
86.743 49.8 08 23.5 006 00.84 00.8 00.03
05gisp
00.1 0101 28.4 016 00.81 00.8 00.03
88.2 054 28.4 016 00.42 00.8 00.03
00.5 061 28.4 016 00.63 00.8 00.03
37.553 00.8 08 28.4 016 00.84 00.8 00.03
051gisp
00.1 0712 34.4 0131 00.81 00.8 00.03
56.2 089 34.4 0131 00.42 00.8 00.03
59.4 053 34.4 0131 00.63 00.8 00.03
08.653 53.7 081 34.4 0131 00.84
)PV&PF(ETALPEGNALF
521.1
521.1
521.1
521.1
521.1
521.1
521.1
521.1
521.1
521.1
521.1
521.1 00.8 00.03
003gisp
79.0 0278 07.2 0525 00.81 00.01 00.03
16.1 0293 07.2 0525 00.42 00.01 00.03
20.3 0041 07.2 0525 00.63 00.01 00.03
00.853 84.4 017 07.2 0525 00.84
)RV&RF(DEGROFEGNALF
578.2
578.2
578.2
578.2
578.2
578.2
578.2
578.2
578.2
578.2
578.2
578.2
57.3
57.3
57.3
57.3 00.01 00.03
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 11/8" thick; 150# ANSI B16.5 drilling (A-36).
Standard materials (Cont.)Pipe: Standard Wt. (A53-B/A106-B).Elbow: Standard Wt. 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of
-20˚ F to 600˚ F. If forged flanged ends are specified, the maximum temperature rating for 150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial Compression
Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
20"
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
50
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)RV&RF(DEGROFEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
57.1 029 23.5 074 00.81 521.3 00.8 00.33
29.2 014 23.5 074 00.42 521.3 00.8 00.33
74.5 051 23.5 074 00.63 521.3 00.8 00.33
64.124 21.8 07 23.5 074 00.84 521.3 00.8 00.33
05gisp
00.1 0231 87.4 076 00.81 521.3 00.8 00.33
00.2 006 87.4 076 00.42 521.3 00.8 00.33
98.4 012 87.4 076 00.63 521.3 00.8 00.33
37.524 62.7 011 87.4 076 00.84 521.3 00.8 00.33
051gisp
00.1 0482 04.4 0441 00.81 521.3 00.8 00.33
00.2 0821 04.4 0441 00.42 521.3 00.8 00.33
94.4 064 04.4 0441 00.63 521.3 00.8 00.33
09.624 76.6 032 04.4 0441 00.84
)PV&PF(ETALPEGNALF
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1
5781.1521.3 00.8 00.33
003gisp
88.0 04411 96.2 0675 00.81 00.4 00.01 00.33
64.1 0515 96.2 0675 00.42 00.4 00.01 00.33
47.2 0381 96.2 0675 00.63 00.4 00.01 00.33
22.824 70.4 039 96.2 0675 00.84 00.4 00.01 00.33
22 U T 150 2.00 WS WS L C 40"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 13/16" thick; 150# ANSI B16.5 drilling (A-36).
Standard materials (Cont.)Pipe: 25 to 150 psig; Standard Wt. (A53-B/A106-B)
300 psig; SCH. 80s (0.5" Wall) (A106-B/A516-70).Elbow: 25 to 150 psig; Standard Wt. 90˚ L.R. (A234 WPB)
300 psig; SCH. 80s (0.5" Wall) 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of
-20˚ F to 600˚ F. If forged flanged ends are specified, themaximum temperature rating for 150 psig design is 500˚F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial
Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
22"
Flow
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
51
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
24 U T 150 2.00 EL EL L2 C2 96" B2 E2
SETARGNIRPS&STNEMEVOM)ni/sbl()sehcni()ni/sbl()sehcni(
LASREVINUHTGNEL
NIATBOOTHTGNELLASREVINUOTDDA)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni( )SW(
DNEDLEW)LE(WOBLE
52gisp
65.1 019 65.4 044 00.81 00.01 00.63
25.2 024 65.4 044 00.42 00.01 00.63
75.4 051 65.4 044 00.63 00.01 00.63
33.205 76.6 08 65.4 044 00.84 00.01 00.63
05gisp
00.1 0471 70.4 058 00.81 00.01 00.63
00.2 018 70.4 058 00.42 00.01 00.63
00.4 003 70.4 058 00.63 00.01 00.63
10.205 69.5 051 70.4 058 00.84 00.01 00.63
051gisp
00.1 0473 57.3 0281 00.81 00.01 00.63
00.2 0471 57.3 0281 00.42 00.01 00.63
57.3 046 57.3 0281 00.63 00.01 00.63
82.305 84.5 033 57.3 0281 00.84
)PV&PF(ETALPEGNALF
52.1
52.1
52.1
52.1
52.1
52.1
52.1
52.1
52.1
52.1
52.1
52.1 00.01 00.63
003gisp
87.0 07051 92.2 0237 00.81 00.01 00.63
62.1 0007 92.2 0237 00.42 00.01 00.63
92.2 0852 92.2 0237 00.63 00.01 00.63
27.405 43.3 0231 92.2 0237 00.84
)RV&RF(DEGROFEGNALF
52.3
52.3
52.3
52.3
52.3
52.3
52.3
52.3
52.3
52.3
52.3
52.3
5781.4
5781.4
5781.4
5781.4 00.01 00.63
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
24"
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 to 150 psig; 150# ANSI B16.5 RFSO (A105)
300 psig; 300# ANSI B16.5 RFSO (A105).Plate Flanges: 11/4" thick; 150# ANSI B16.5 drilling (A-36).
Standard materials (Cont.)Pipe: 25 to 150 psig; Standard Wt. (A53-B/A106-B)
300 psig; SCH.80s (0.5" Wall) (A106-B/A516-70).Elbow: 25 to 150 psig; Standard Wt. 90˚ L.R. (A234 WPB)
300 psig; SCH. 80s (0.5" Wall) 90˚ L.R. (A234 WPB).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of
-20˚ F to 600˚ F. If forged flanged ends are specified, the maximum temperature rating for 150 psig design is 500˚ F.
• Consult factory for temperature rating of plate flanges.• Maximum Axial Extension is 15% of Axial Compression
Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.
Flow
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
52
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
SETARGNIRPS&STNEMEVOM)ni/sbl()sehcni()ni/sbl()sehcni(
LASREVINUHTGNEL
NIATBOOTHTGNELLASREVINUOTDDA)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
00.1 0591 65.4 028 00.81 00.01 00.93
43.2 019 65.4 028 00.42 00.01 00.93
32.4 033 65.4 028 00.63 00.01 00.93
72.585 81.6 071 65.4 028 00.84 00.01 00.93
05gisp
00.1 0912 50.4 029 00.81 00.01 00.93
00.2 0201 50.4 029 00.42 00.01 00.93
67.3 073 50.4 029 00.63 00.01 00.93
85.485 94.5 091 50.4 029 00.84
)RV&RF(DEGROFEGNALF
57.1
57.1
57.1
57.1
57.1
57.1
57.1
57.1 00.01 00.93
051gisp
00.1 0074 37.3 0791 00.81 00.01 00.93
19.1 0812 37.3 0791 00.42 00.01 00.93
64.3 008 37.3 0791 00.63 00.01 00.93
59.585 50.5 014 37.3 0791 00.84 00.01 00.93
26 U O 150 3.46 WS WS 56"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
26"
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 & 50 psig designs; 125# LW F.F.S.O. (A105).
Customer to advise flange specification for 150 psig design.Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 25 to 150 psig; Standard Wt. (3/8" Wall)(A53-B/A106-B/A-36/A516-70).Elbow: Standard Wt. (3/8" wall) 90˚ L.R.
(A234 WPB/A-36/A516-70/A53-B/A106-B).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 300 psig designs can be provided upon request.
Customer to
advise
Flange Specification.
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
53
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
28 U T 025 3.94 EL EL 120"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 & 50 psig designs; 125# LW F.F.S.O. (A105).
Customer to advise flange specification for 150 psig design.Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 25 to 150 psig; Standard Wt. (3/8" Wall)(A53-B/A106-B/A-36/A516-70).Elbow: Standard Wt. (3/8" wall) 90˚ L.R.
(A234 WPB/A-36/A516-70/A53-B/A106-B).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F. If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 300 psig designs can be provided upon request.
28"
SETARGNIRPS&STNEMEVOM)ni/sbl()sehcni()ni/sbl()sehcni(
LASREVINUHTGNEL
NIATBOOTHTGNELLASREVINUOTDDA)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
00.1 0242 65.4 088 00.81 00.01 00.24
00.2 0211 65.4 088 00.42 00.01 00.24
49.3 014 65.4 088 00.63 00.01 00.24
71.476 67.5 012 65.4 088 00.84 00.01 00.24
05gisp
00.1 0172 30.4 099 00.81 00.01 00.24
39.1 0621 30.4 099 00.42 00.01 00.24
00.3 064 30.4 099 00.63 00.01 00.24
34.376 00.5 042 30.4 099 00.84
)RV&RF(DEGROFEGNALF
57.1
57.1
57.1
57.1
57.1
57.1
57.1
57.1 00.01 00.24
051gisp
00.1 0907 96.3 0622 00.81 00.01 00.24
56.1 0923 96.3 0622 00.42 00.01 00.24
99.2 0121 96.3 0622 00.63 00.01 00.24
09.476 63.4 026 96.3 0622 00.84 00.01 00.24
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to
advise
Flange Specification.
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
54
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
30 U O 050 3.00 WS WS L 56" B4 E4
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
30"
SETARGNIRPS&STNEMEVOM)ni/sbl()sehcni()ni/sbl()sehcni(
LASREVINUHTGNEL
NIATBOOTHTGNELLASREVINUOTDDA)sehcni(HTGNELLLAREVO .TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)RV&RF(DEGROFEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
00.1 0492 65.4 049 00.81 57.1 00.01 00.54
00.2 0731 65.4 049 00.42 57.1 00.01 00.54
96.3 005 65.4 049 00.63 57.1 00.01 00.54
53.967 93.5 062 65.4 049 00.84 57.1 00.01 00.54
05gisp
00.1 0033 10.4 0501 00.81 57.1 00.01 00.54
08.1 0351 10.4 0501 00.42 57.1 00.01 00.54
00.3 065 10.4 0501 00.63 57.1 00.01 00.54
65.867 47.4 092 10.4 0501 00.84 57.1 00.01 00.54
051gisp
00.1 0907 96.3 0622 00.81 00.01 00.54
56.1 0923 96.3 0622 00.42 00.01 00.54
99.2 0121 96.3 0622 00.63 00.01 00.54
41.077 63.4 026 96.3 0622 00.84 00.01 00.54
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 & 50 psig designs; 125# LW F.F.S.O. (A105).
Customer to advise flange specification for 150 psig design.Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 25 to 150 psig; Standard Wt. (3/8" Wall)(A53-B/A106-B/A-36/A516-70).Elbow: Standard Wt. (3/8" wall) 90˚ L.R.
(A234 WPB/A-36/A516-70/A53-B/A106-B).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 300 psig designs can be provided upon request.
Flow
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to
advise
Flange Specification.
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
55
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
34 U T 050 2.86 WS WS L C 56"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
32" and 34"
"23SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
).ni(HTGNELLLAREVO .TF21EVOBA"8/3±;.TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
00.1 0453 65.4 0001 00.81 00.01 00.8429.1 0461 65.4 0001 00.42 00.01 00.84
74.3 016 65.4 0001 00.63 00.01 00.84
28.078 70.5 013 65.4 0001 00.84 00.01 00.84
05gisp
00.1 0893 00.4 0211 00.81 00.01 00.8400.1 0581 00.4 0211 00.42 00.01 00.84
00.3 086 00.4 0211 00.63 00.01 00.84
69.968 44.4 053 00.4 0211 00.84 00.01 00.84
"43
52gisp
00.1 0224 65.4 0601 00.81 00.01 00.1518.1 0691 65.4 0601 00.42 00.01 00.15
72.3 027 65.4 0601 00.63 00.01 00.15
75.879 87.4 073 65.4 0601 00.84 00.01 00.15
05gisp
89.0 0474 89.3 0911 00.81 00.01 00.1500.1 0022 89.3 0911 00.42 00.01 00.15
68.2 018 89.3 0911 00.63 00.01 00.15
86.779 00.4 024 89.3 0911 00.84
)RV&RF(DEGROFEGNALF
57.157.1
57.1
57.1
57.157.1
57.1
57.1
57.157.1
57.1
57.1
57.157.1
57.1
57.1 00.01 00.15
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 & 50 psig designs; 125# LW F.F.S.O. (A105).Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 25 & 50 psig; Standard Wt. (3/8" Wall)(A53-B/A106-B/A-36/A516-70).Elbow: Standard Wt. (3/8" wall) 90˚ L.R. (A234 WPB/A-36/A516-70/A53-B/A106-B).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F. If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 150 & 300 psig designs can be provided upon request.
Customer to specify
Plate FlangeDimensions
Flow
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
56
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
"63SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
).ni(HTGNELLLAREVO .TF21EVOBA"8/3±;.TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
68.1 0771 98.5 027 00.42 00.01 00.4585.3 016 98.5 027 00.63 00.01 00.45
83.5 013 98.5 027 00.84 00.01 00.45
49.9901 12.7 081 98.5 027 00.06 00.01 00.45
05gisp
00.1 0093 65.4 0851 00.42 00.01 00.4577.2 0631 65.4 0851 00.63 00.01 00.45
61.4 086 65.4 0851 00.84 00.01 00.45
74.9901 85.5 004 65.4 0851 00.06 00.01 00.45
"83
52gisp
77.1 0702 98.5 067 00.42 00.01 00.7504.3 027 98.5 067 00.63 00.01 00.75
01.5 063 98.5 067 00.84 00.01 00.75
56.0221 58.6 012 98.5 067 00.06 00.01 00.75
05gisp
00.1 0654 45.4 0761 00.42 00.01 00.7526.2 0851 45.4 0761 00.63 00.01 00.75
49.3 097 45.4 0761 00.84 00.01 00.75
51.0221 82.5 074 45.4 0761 00.06
)RV&RF(DEGROFEGNALF
57.157.1
57.1
57.1
57.157.1
57.1
57.1
57.157.1
57.1
57.1
57.157.1
57.1
57.1 00.01 00.75
36 U T 050 2.77 FR FR 391/2"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
36" and 38"
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 & 50 psig designs; 125# LW F.F.S.O. (A105).Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 25 & 50 psig; Standard Wt. (3/8" Wall)(A53-B/A106-B/A-36/A516-70).Elbow: Standard Wt. (3/8" wall) 90˚ L.R. (A234 WPB/A-36/A516-70/A53-B/A106-B).
• Maximum Test Pressure is 1.5 X Rated Pressure.• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.
If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.• Cycle Life = 3,000 minimum (EJMA).• Movements are non-concurrent.• 150 & 300 psig designs can be provided upon request.
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
57
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
40 U T 050 2.49 FR EL 973/4"
"04SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
).ni(HTGNELLLAREVO .TF21EVOBA"8/3±;.TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
86.1 0042 98.5 097 00.42 00.01 00.0632.3 038 98.5 097 00.63 00.01 00.06
68.4 024 98.5 097 00.84 00.01 00.06
46.7431 25.6 052 98.5 097 00.06 00.01 00.06
05gisp
00.1 0925 35.4 0571 00.42 00.01 00.0694.2 0481 35.4 0571 00.63 00.01 00.06
47.3 029 35.4 0571 00.84 00.01 00.06
21.7431 20.5 055 35.4 0571 00.06 00.01 00.06
"24
52gisp
16.1 0672 98.5 038 00.42 00.01 00.3680.3 069 98.5 038 00.63 00.01 00.36
36.4 084 98.5 038 00.84 00.01 00.36
29.0841 22.6 082 98.5 038 00.06 00.01 00.36
05gisp
00.1 0806 35.4 0381 00.42 00.01 00.3673.2 0112 35.4 0381 00.63 00.01 00.36
75.3 0501 35.4 0381 00.84 00.01 00.36
73.0841 87.4 036 35.4 0381 00.06
)RV&RF(DEGROFEGNALF
57.157.1
57.1
57.1
57.157.1
57.1
57.1
57.157.1
57.1
57.1
57.157.1
57.1
57.1 00.01 00.36
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
40" and 42"
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 & 50 psig designs; 125# LW F.F.S.O. (A105).Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 25 & 50 psig; Standard Wt. (3/8" Wall)(A53-B/A106-B/A-36/A516-70).Elbow: Standard Wt. (3/8" wall) 90˚ L.R. (A234 WPB/A-36/A516-70/A53-B/A106-B).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F. If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 150 & 300 psig designs can be provided upon request.
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
58
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
46 U O 050 2.00 WS WS L 56"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
44" and 46"
"44SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
).ni(HTGNELLLAREVO .TF21EVOBA"8/3±;.TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
35.1 0613 98.5 078 00.42 00.01 00.6659.2 0011 98.5 078 00.63 00.01 00.66
34.4 055 98.5 078 00.84 00.01 00.66
84.0261 49.5 033 98.5 078 00.06 00.01 00.66
05gisp
00.1 0596 35.4 0291 00.42 00.01 00.6600.2 0142 35.4 0291 00.63 00.01 00.66
14.3 0021 35.4 0291 00.84 00.01 00.66
09.9161 75.4 027 35.4 0291 00.06 00.01 00.66
"64
52gisp
74.1 0953 98.5 019 00.42 00.01 00.9628.2 0521 98.5 019 00.63 00.01 00.96
42.4 026 98.5 019 00.84 00.01 00.96
23.6671 96.5 073 98.5 019 00.06 00.01 00.96
05gisp
00.1 0097 25.4 0002 00.42 00.01 00.9600.2 0472 25.4 0002 00.63 00.01 00.96
62.3 0731 25.4 0002 00.84 00.01 00.96
27.5671 73.4 028 25.4 0002 00.06
)RV&RF(DEGROFEGNALF
52.252.2
52.2
52.2
52.252.2
52.2
52.2
52.252.2
52.2
52.2
52.252.2
52.2
52.2 00.01 00.96
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 25 & 50 psig designs; 125# LW F.F.S.O. (A105).Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 25 & 50 psig; Standard Wt. (3/8" wall) (A53-B/A106-B/A-36/A516-70).Elbow: Standard Wt. (3/8" wall) 90˚ L.R. (Fabricated with pipe & mitered).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F. If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 150 & 300 psig designs can be provided upon request.
Flow
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
59
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
52 U T 025 2.44 FR FR 41"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
48", 50" & 52"
"84SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
).ni(HTGNELLLAREVO .TF21EVOBA"8/3±;.TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
00.1 0779 47.5 0722 00.42 00.8 00.27
00.2 0933 47.5 0722 00.63 00.8 00.27
79.3 0961 47.5 0722 00.84 00.8 00.27
96.9191 00.5 0101 47.5 0722 00.06 00.8 00.27
"05
52gisp
00.1 09901 47.5 0632 00.42 00.8 00.57
00.2 0283 47.5 0632 00.63 00.8 00.57
18.3 0091 47.5 0632 00.84 00.8 00.57
51.8702 00.5 0411 47.5 0632 00.06 00.8 00.57
"25
52gisp
00.1 0776 07.5 0531 00.42 00.8 00.87
44.2 0732 07.5 0531 00.63 00.8 00.87
56.3 0911 07.5 0531 00.84 00.8 00.87
50.5822 98.4 017 07.5 0531 00.06
)RV&RF(DEGROFEGNALF
05.2
05.2
05.2
05.2
05.2
05.2
05.2
05.2
05.2
05.2
05.2
05.2 00.8 00.87
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals).Flanges: 125# LW F.F.S.O. (A105).Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: Standard Wt. (3/8" wall) (A53-B/A106-B/A-36/A516-70).Elbow: Standard Wt. (3/8" wall) 90˚ L.R.
(Fabricated with pipe & mitered).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 50, 150 & 300 psig designs can be provided for 48" Dia. upon request.
• 50 & 150 psig designs can be provided for 50" & 52" Dia. upon request.
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
60
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
56 U T 025 2.27 WS WS L C 56"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
54",56" & 58"
"45SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
).ni(HTGNELLLAREVO .TF21EVOBA"8/3±;.TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
00.1 0557 07.5 0041 00.42 00.01 00.18
53.2 0462 07.5 0041 00.63 00.01 00.18
25.3 0231 07.5 0041 00.84 00.01 00.18
56.7542 17.4 097 07.5 0041 00.06
)RV&RF(DEGROFEGNALF
05.2
05.2
05.2
05.2 00.01 00.18
"65
52gisp
00.1 0838 07.5 0541 00.42 00.01 00.48
72.2 0492 07.5 0541 00.63 00.01 00.48
04.3 0741 07.5 0541 00.84 00.01 00.48
35.6362 55.4 088 07.5 0541 00.06 00.01 00.48
"85
52gisp
00.1 0829 07.5 0051 00.42 00.01 00.78
02.2 0523 07.5 0051 00.63 00.01 00.78
92.3 0361 07.5 0051 00.84 00.01 00.78
96.1282 04.4 079 07.5 0051 00.06 00.01 00.78
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals) .Flanges: 125# LW F.F.S.O. (A105); (54" Dia. only).Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 3/8" wall (A-36/A516-70)Elbow: 3/8" wall; 90˚ L.R. (Fabricated with pipe & mitered).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F. If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 50 psig designs can be provided upon request.
125# LW
Flanges are
not available
in this size.
125# LW
Flanges are
not available
in this size.
Flow
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
61
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
66 U O 025 1.00 WS WS 44"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
60",66" & 72"
"06SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
).ni(HTGNELLLAREVO .TF21EVOBA"8/3±;.TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
00.1 03201 07.5 0551 00.42 00.01 00.09
21.2 0853 07.5 0551 00.63 00.01 00.09
81.3 0971 07.5 0551 00.84 00.01 00.09
41.3103 62.4 0701 07.5 0551 00.06 00.01 00.09
"66
52gisp
00.1 08431 07.5 0071 00.42 00.01 00.99
49.1 0274 07.5 0071 00.63 00.01 00.99
09.2 0632 07.5 0071 00.84 00.01 00.99
81.5263 88.3 0141 07.5 0071 00.06 00.01 00.99
"27
52gisp
39.0 05371 07.5 0581 00.42 00.01 00.801
87.1 0706 07.5 0581 00.63 00.01 00.801
66.2 0403 07.5 0581 00.84 00.01 00.801
67.3924 75.3 0281 07.5 0581 00.06
)RV&RF(DEGROFEGNALF
57.2
57.2
57.2
57.2
57.2
57.2
57.2
57.2
57.2
57.2
57.2
57.2 00.01 00.801
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals) .Flanges: 125# LW F.F.S.O. (A105).Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 3/8" wall (A-36/A516-70).Elbow: 3/8" wall; 90˚ L.R. (Fabricated with pipe & mitered).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F. If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 50 psig designs can be provided upon request.
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
62
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
78 U O 025 2.46 WS WS L 72"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
78",84" & 90"
"87SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
).ni(HTGNELLLAREVO .TF21EVOBA"8/3±;.TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)RV&RF(DEGROFEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
68.0 09812 07.5 0991 00.42 00.21 00.711
56.1 0667 07.5 0991 00.63 00.21 00.711
64.2 0483 07.5 0991 00.84 00.21 00.711
09.8105 03.3 0032 07.5 0991 00.06 00.21 00.711
"48
52gisp
08.0 05172 07.5 0412 00.42 00.3 00.21 00.621
35.1 0159 07.5 0412 00.63 00.3 00.21 00.621
92.2 0674 07.5 0412 00.84 00.3 00.21 00.621
85.0085 70.3 0582 07.5 0412 00.06 00.3 00.21 00.621
"09
52gisp
57.0 00233 07.5 0922 00.42 00.21 00.531
34.1 02611 07.5 0922 00.63 00.21 00.531
41.2 0285 07.5 0922 00.84 00.21 00.531
18.8366 78.2 0843 07.5 0922 00.06 00.21 00.531
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals). Flanges: 125# LW F.F.S.O. (A105); (84" Dia. Only).Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 3/8" wall (A-36/A516-70).Elbow: 3/8" wall; 90˚ L.R. (Fabricated with pipe & mitered).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F.If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 50 psig designs can be provided upon request.
125# LW
Flanges are
not available
in this size.
125# LW
Flanges are
not available
in this size.
Flow
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
MONEZIS
TINUEPYT
TINUELYTS
NGISED.SSERP
LARETALTNEMEVOM
DNESGNITTIF
)83egaPeeS(
RENIL/W
L'TAM
REVOC/W
L'TAM
LLAREVOHTGNEL
SLAIRETAMLAICEPS
SWOLLEB DNE
L'TAM L'TAM
- - - - - - - -
63
Universal Expansion Joints
PART NUMBER EXAMPLE:
This part number describes the unit pictured above.
96 U O 025 2.00 FR FR L 541/2"
FMH EXPANSION JOINTS 1-800-359-4673 • (770) 493-1100 • Fax: (770) 493-1410 • E-mail: [email protected]
Nominal Diameter
➢
➢
96", 102" & 120"
"69SETARGNIRPS&STNEMEVOM
)ni/sbl()sehcni()ni/sbl()sehcni(LASREVINU
HTGNELNIATBOOTHTGNELLASREVINUOTDDA
).ni(HTGNELLLAREVO .TF21EVOBA"8/3±;.TF3EVOBA"4/1±;"8/1±
LARETALTNEMEVOM
LARETALGNIRPS
ETARLAIXA.PMOC
LAIXAGNIRPS
ETAR)sehcni(
)PV&PF(ETALPEGNALF
)RV&RF(DEGROFEGNALF
)SW(DNEDLEW
)LE(WOBLE
52gisp
17.0 09993 07.5 0342 00.42 52.3 00.21 00.441
00.1 00041 07.5 0342 00.63 52.3 00.21 00.441
00.2 0107 07.5 0342 00.84 52.3 00.21 00.441
95.3357 96.2 0914 07.5 0342 00.06 52.3 00.21 00.441
"201
52gisp
66.0 05674 07.5 0752 00.42 00.21 00.351
72.1 09661 07.5 0752 00.63 00.21 00.351
09.1 0638 07.5 0752 00.84 00.21 00.351
29.4848 45.2 0005 07.5 0752 00.06 00.21 00.351
"021
52gisp
65.0 00304 07.5 0651 00.42 00.21 00.081
70.1 01141 07.5 0651 00.63 00.21 00.081
16.1 0707 07.5 0651 00.84 00.21 00.081
71.47711 51.2 0324 07.5 0651 00.06 00.21 00.081
Standard materials of constructionBellows: A240 T321.Liners: A240 T304 (when liner is requested).Covers: Carbon Steel (when cover is requested).Hardware: Carbon Steel (Tie Rods, Hinges, Gimbals). Flanges: 125# LW F.F.S.O. (A105); (96" Dia. Only).Plate Flanges: Available upon request and with dimensional
information provided by customer.Pipe: 3/8" wall (A-36/A516-70).Elbow: 3/8" wall; 90˚ L.R. (Fabricated with pipe & mitered).
• Maximum Test Pressure is 1.5 X Rated Pressure.
• Pressure Rating is based on a design temperature of -20˚ F to 600˚ F. If flanged ends are required, please consult factory for maximum temperature rating.
• Maximum Axial Extension is 15% of Axial Compression Value shown above.
• Cycle Life = 3,000 minimum (EJMA).
• Movements are non-concurrent.
• 50 psig designs can be provided upon request.
125# LW
Flanges are
not available
in this size.
125# LW
Flanges are
not available
in this size.
Flow
UNIT TYPEU = UNIVERSALD = DUAL
UNIT STYLEO = UNRESTRAINEDT = TIE RODS/LIMIT RODS/
CONTROL RODSH = HINGEG = GIMBAL
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions
Customer to specify
Plate FlangeDimensions