vauxhall adam owner's manual · press release button, adjust height, engage. head restraints 3...

Vauxhall AdamOwner's Manual

Introduction .................................... 2In brief ............................................ 6Keys, doors and windows ............ 19Seats, restraints ........................... 32Storage ........................................ 51Instruments and controls ............. 69Lighting ...................................... 105Climate control ........................... 113Driving and operating ................. 123Vehicle care ............................... 160Service and maintenance .......... 209Technical data ........................... 212Customer information ................ 225Index .......................................... 232

Contents

2 Introduction

Introduction

Introduction 3

Vehicle specific dataPlease enter your vehicle's data onthe previous page to keep it easilyaccessible. This information isavailable in the sections "Service andmaintenance" and "Technical data"as well as on the identification plate.

IntroductionYour vehicle is a designedcombination of advanced technology,safety, environmental friendlinessand economy.This Owner's Manual provides youwith all the necessary information toenable you to drive your vehiclesafely and efficiently.Make sure your passengers areaware of the possible risk of accidentand injury which may result fromimproper use of the vehicle.You must always comply with thespecific laws and regulations of thecountry that you are in. These lawsmay differ from the information in thisOwner's Manual.Disregarding the description given inthis manual may affect your warranty.

When this Owner's Manual refers to aworkshop visit, we recommend yourVauxhall Authorised Repairer.For gas vehicles, we recommend aVauxhall Authorised Repairerlicensed to service gas vehicles.All Vauxhall Authorised Repairersprovide first-class service atreasonable prices. Experiencedmechanics trained by Vauxhall workaccording to specific Vauxhallinstructions.The customer literature pack shouldalways be kept ready to hand in thevehicle.

Using this manual● This manual describes all options

and features available for thismodel. Certain descriptions,including those for display andmenu functions, may not apply toyour vehicle due to modelvariant, country specifications,special equipment oraccessories.

● The "In brief" section will give youan initial overview.

● The table of contents at thebeginning of this manual andwithin each section shows wherethe information is located.

● The index will enable you tosearch for specific information.

● This Owner's Manual depicts left-hand drive vehicles. Operation issimilar for right-hand drivevehicles.

● The Owner's Manual uses theengine identifier code. Thecorresponding sales designationand engineering code can befound in the section "Technicaldata".

● Directional data, e.g. left or right,or front or back, always relate tothe direction of travel.

● Displays may not support yourspecific language.

● Display messages and interiorlabelling are written in boldletters.

4 Introduction

Danger, Warnings andCautions

9 Danger

Text marked 9 Danger providesinformation on risk of fatal injury.Disregarding this information mayendanger life.

9 Warning

Text marked 9 Warning providesinformation on risk of accident orinjury. Disregarding thisinformation may lead to injury.

Caution

Text marked Caution providesinformation on possible damage tothe vehicle. Disregarding thisinformation may lead to vehicledamage.

SymbolsPage references are indicated with 3.3 means "see page".Page references and index entriesrefer to the indented headings givenin the section table of content.Thank you for choosing a Vauxhall.We wish you many hours ofpleasurable driving.Your Vauxhall Team

Introduction 5

6 In brief

In brief

Initial drive information

Vehicle unlocking

Press c to unlock the doors and loadcompartment. Open the doors bypulling the handles.

To open the tailgate, press the brandemblem at the bottom half.Radio remote control 3 20, Centrallocking system 3 22, Loadcompartment 3 24.

In brief 7

Seat adjustmentLongitudinal adjustment

Pull handle, slide seat, releasehandle. Try to move the seat back andforth to ensure that the seat is lockedin place.Seat position 3 33, Seat adjustment3 34.

Backrest inclination

Turn handwheel to adjust inclination.Do not lean on backrest whileadjusting.Seat position 3 33, Seat adjustment3 34, Seat folding 3 35.

Seat height

Lever pumping motionup : seat higherdown : seat lower

Seat position 3 33, Seat adjustment3 34.

8 In brief

Head restraint adjustment

Press release button, adjust height,engage.Head restraints 3 32.

Seat belt

Pull out the seat belt and engage inbelt buckle. The seat belt must not betwisted and must fit close against thebody. The backrest must not be tiltedback too far (maximum approx. 25 °).To release belt, press red button onbelt buckle.Seat position 3 33, Seat belts3 37, Airbag system 3 39.

Mirror adjustmentInterior mirror

To adjust the mirror, move the mirrorhousing in the desired direction.Manual anti-dazzle interior mirror3 28.Automatic anti-dazzle interior mirror3 28.

In brief 9

Exterior mirrors

Select the relevant exterior mirror andadjust it.Convex exterior mirrors 3 27,Electric adjustment 3 27, Foldingexterior mirrors 3 27.Heated exterior mirrors 3 28.

Steering wheel adjustment

Unlock the lever, adjust the steeringwheel, then engage the lever andensure it is fully locked.Do not adjust the steering wheelunless the vehicle is stationary andthe steering wheel lock has beenreleased.Airbag system 3 39, Ignitionpositions 3 124.

10 In brief

Instrument panel overview

In brief 11

1 Power windows ..................... 292 Exterior mirrors ..................... 273 Cruise control ..................... 139

Speed limiter ....................... 1414 Side air vents ...................... 1215 Turn and lane-change

signals, headlight flash,low beam and high beam .... 108

Exit lighting ......................... 111

Parking lights ...................... 108

Buttons for DriverInformation Centre ................ 88

6 Instruments .......................... 787 Steering wheel controls ....... 708 Driver Information Centre ...... 889 Windscreen wiper,

windscreen washersystem, headlight washersystem, rear wiper, rearwasher system ...................... 71

10 Central locking system .......... 22

City mode ............................ 138Fuel selector ......................... 79

Eco button for stop-startsystem ................................. 126Traction Control system ..... 136

Electronic Stability Control . 137Parking assist ..................... 142Seat heating .......................... 36Heated steering wheel .......... 70

11 Colour-Info-Display .............. 93Graphic-Info-Display ............. 94

12 Hazard warning flashers .... 107

Control indicator for airbagdeactivation .......................... 84

Control indicator for frontpassenger seat belt ............. 83

13 Anti-theft alarm systemstatus LED ........................... 25

14 Centre air vents .................. 12115 Side air vents passenger

side ..................................... 12116 Glovebox .............................. 51

Fuse box ............................ 18017 Climate control system ........ 11318 Power outlet .......................... 76

19 AUX input, USB input ........... 1020 Selector lever,

transmission ....................... 13021 Parking brake ...................... 13522 Ignition switch with

steering wheel lock ............ 12423 Horn ..................................... 71

Driver airbag ........................ 4224 Bonnet release lever .......... 16225 Steering wheel adjustment . . 7026 Light switch ........................ 105

Headlight rangeadjustment ......................... 107

Rear fog light ...................... 108

Brightness of instrumentpanel illumination ................ 109Brightness of ambient light 109

12 In brief

Exterior lightingLight switch

Turn light switch:7 : lights off8 : sidelights9 : headlights

Light switch with automatic lightcontrol

AUTO : automatic light control:exterior lighting is switchedon and off automatically

m : activation or deactivation ofthe automatic light control

8 : sidelights9 : headlights

Automatic light control 3 106.

Rear fog lightPress r in the light switch.

Headlight flash, high beam andlow beam

headlight flash : pull leverhigh beam : push leverlow beam : push or pull lever

High beam 3 106, Headlight flash3 106.

In brief 13

Turn and lane-change signals

lever up : right turn signallever down : left turn signal

Turn and lane-change signals3 108, Parking lights 3 108.

Hazard warning flashers

Operated by pressing ¨.Hazard warning flashers 3 107.

Horn

Press j.

14 In brief

Washer and wiper systemsWindscreen wiper

HI : fastLO : slowINT : interval wiping

orautomatic wiping with rainsensor

OFF : off

For a single wipe when thewindscreen wiper is off, press thelever down to position 1x.Windscreen wiper 3 71, Wiperblade replacement 3 167.

Windscreen washer

Pull lever.Windscreen washer system 3 71,Washer fluid 3 164.

Rear window wiper

Press the rocker switch to activate therear window wiper:upper switch : continuous

operationlower switch : intermittent

operationmiddle position : off

In brief 15

Rear window washer

Push lever.Washer fluid is sprayed on the rearwindow and the wiper wipes a fewtimes.Rear window wiper/washer 3 73.

Climate controlHeated rear window

The heating is operated by pressingÜ.Heated rear window 3 30.

Heated exterior mirrorsPressing Ü also activates the heatedexterior mirrors.Heated exterior mirror 3 28.

Demisting and defrosting thewindows

● Set air distribution control to l.● Press V.● Set temperature control to

warmest level.● Set fan speed to highest level.● Switch on heated rear window Ü.● Open side air vents as required

and direct them towards the doorwindows.

Climate control system 3 113.

16 In brief

TransmissionManual transmission

Reverse: with the vehicle stationary,depress clutch pedal and press therelease button on the selector leverand engage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Manual transmission 3 130.

Manual transmission automated

N : neutral positionD/M : switch between automatic (D)

and manual (M) shift mode. Dor M is indicated in thetransmission display

< : upshifting in manual mode] : downshifting in manual modeR : reverse, engage only when

vehicle is stationary

Manual transmission automated3 130.

Starting offCheck before starting off● tyre pressure and condition

3 184, 3 223● engine oil level and fluid levels

3 163● all windows, mirrors, exterior

lighting and number plates arefree from dirt, snow and ice andare operational

● proper position of mirrors, seats,and seat belts 3 27, 3 33,3 38

● brake function at low speed,particularly if the brakes are wet

In brief 17

Starting the engine

● Turn key to position 1.● Move the steering wheel slightly

to release the steering wheellock.

● Manual transmission: operateclutch and brake pedal.Manual transmission automated:operate brake pedal.

● Do not operate accelerator pedal.● Turn key to position 3 and

release.Starting the engine 3 125.

Stop-start system

If the vehicle is at a low speed or at astandstill and certain conditions arefulfilled, activate an Autostop asfollows:Vehicles with manual transmission● Depress the clutch pedal.● Set the lever in neutral.● Release the clutch pedal.

An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.To restart the engine, depress theclutch pedal again.

Vehicles with manual transmissionautomatedIf the vehicle is at a standstill withdepressed brake pedal, Autostop isactivated automatically, indicated bythe needle at the AUTOSTOPposition in the tachometer.Release the brake pedal or moveselector lever out of D to restart theengine.Stop-start system 3 126.

18 In brief

Parking

9 Warning

● Do not park the vehicle on aneasily ignitable surface. Thehigh temperature of theexhaust system could ignite thesurface.

● Always apply the parkingbrake. Activate the parkingbrake without pressing therelease button. Apply as firmlyas possible on a downhill slopeor uphill slope. Depress brakepedal at the same time toreduce operating force.

● Switch off the engine.● If the vehicle is on a level

surface or uphill slope, engagefirst gear before removing theignition key. On an uphill slope,turn the front wheels away fromthe kerb.If the vehicle is on a downhillslope, engage reverse gearbefore removing the ignition

key. Turn the front wheelstowards the kerb.

● Close the windows and thesunroof.

● Remove the ignition key fromthe ignition switch. Turn thesteering wheel until thesteering wheel lock is felt toengage.For vehicles with manualtransmission automated, thekey can only be removed fromthe ignition switch when theparking brake is applied.

● Lock the vehicle by pressing e onthe radio remote control.Activate the anti-theft alarmsystem 3 25.

● The engine cooling fans may runafter the engine has beenswitched off 3 162.

Caution

After running at high enginespeeds or with high engine loads,operate the engine briefly at a lowload or run in neutral forapprox. 30 seconds beforeswitching off, in order to protectthe turbocharger.

Keys, locks 3 19, Laying-up thevehicle for a long period of time3 161.

Keys, doors and windows 19

Keys, doors andwindows

Keys, locks ................................... 19Keys .......................................... 19Car Pass .................................... 20Radio remote control ................. 20Memorised settings ................... 21Central locking system .............. 22Automatic locking ...................... 23

Doors ........................................... 24Load compartment .................... 24

Vehicle security ............................ 25Anti-theft locking system ........... 25Anti-theft alarm system .............. 25Immobiliser ................................ 26

Exterior mirrors ............................ 27Convex shape ........................... 27Electric adjustment .................... 27Folding mirrors .......................... 27Heated mirrors ........................... 28

Interior mirrors ............................. 28Manual anti-dazzle .................... 28Automatic anti-dazzle ................ 28

Windows ...................................... 29Windscreen ............................... 29

Power windows ......................... 29Heated rear window .................. 30Sun visors .................................. 30

Roof ............................................. 31Sunroof ...................................... 31Glass panel ............................... 31

Keys, locksKeys

Caution

Do not attach heavy or bulky itemsto the ignition key.

Replacement keysThe key number is specified in theCar Pass or on a detachable tag.The key number must be quotedwhen ordering replacement keys as itis a component of the immobilisersystem.Locks 3 205.The code number of the adapter forthe locking wheel bolts is specified ona card. It must be quoted whenordering a replacement adapter.Wheel changing 3 194.

20 Keys, doors and windows

Lock cylindersDesigned to free-wheel if they areforcefully rotated without the correctkey or if the correct key is not fullyinserted. To reset, turn cylinder withthe correct key until its slot is vertical,remove key then re-insert it. If thecylinder still free-wheels, turn the keythrough 180° and repeat operation.

Key with foldaway key section

Press button to extend. To fold thekey, first press the button.

Car PassThe Car Pass contains security-related vehicle data and shouldtherefore be kept in a safe place.When the vehicle is taken to aworkshop, this vehicle data is neededin order to perform certain operations.

Radio remote control

Used to operate:● central locking system● anti-theft locking system● anti-theft alarm system● power windows

The radio remote control has a rangeof approx. 20 metres. It can berestricted by external influences. Thehazard warning flashers confirmoperation.Handle with care, protect frommoisture and high temperatures andavoid unnecessary operation.

FaultIf the central locking system cannotbe operated with the radio remotecontrol, it may be due to the following:● The range is exceeded.● The battery voltage is too low.● Frequent, repeated operation of

the radio remote control while notin range, which will require re-synchronisation.

● Overload of the central lockingsystem by operating at frequentintervals, the power supply isinterrupted for a short time.

● Interference from higher-powerradio waves from other sources.

Unlocking 3 22.


Basic settingsSome settings can be changed in theInfo-Display.Vehicle personalisation 3 98.

Radio remote control batteryreplacementReplace the battery as soon as therange reduces.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.

Key with foldaway key section

Extend the key and open the unit.Replace the battery (battery typeCR 2032), paying attention to theinstallation position. Close the unitand synchronise.

Key with fixed key sectionHave the battery replaced by aworkshop.

Radio remote controlsynchronisationAfter replacing the battery, unlock thedoor with the key in the driver's doorlock. The radio remote control will besynchronised when the ignition isswitched on.

Memorised settingsWhenever the key is removed fromthe ignition switch, the followingsettings are automatically memorisedby the key:● lighting● Infotainment system presets● central locking system● comfort settings● climate control

The saved settings are automaticallyused the next time the memorised keyis inserted into the ignition switch andturned to position 1 3 124.A precondition is that Personalizationby driver is activated in the personalsettings of the Info-Display. This mustbe set for each key used.


Vehicle personalisation 3 98.

Central locking systemUnlocks and locks doors, loadcompartment and fuel filler flap.A pull on an interior door handleunlocks the respective door. Pullingthe handle once more opens the door.NoticeIn the event of an accident in whichairbags or belt pretensioners aredeployed, the vehicle isautomatically unlocked.NoticeThree minutes after unlocking withthe remote control, the doors arerelocked automatically if no door hasbeen opened.

Unlocking

Press c.Two settings are selectable in theInfo-Display:● To unlock only the driver's door,

load compartment and fuel fillerflap, press c once. To unlockboth doors, press c twice.

● Press c once to unlock doors,load compartment and fuel fillerflap.

Vehicle personalisation 3 98.The setting can be saved for the keybeing used.Memorised settings 3 21.

Unlocking and opening the tailgate3 24.

LockingClose doors, load compartment andfuel filler flap.

Press e.If the driver's door is not closedproperly, the central locking systemwill not work.

Central locking buttonsLocks or unlocks doors, the loadcompartment and fuel filler flap frominside the passenger compartment.


Press e to lock.Press c to unlock.

Delayed door lockSwitch off engine and remove keyfrom the lock. Press e with at leastone door opened and three chimeswill sound. When the last door isclosed, the vehicle will automaticallylock all doors after five seconds and afeedback is given. After ten minutes,the vehicle will automatically lock alldoors even if a door is still open. Thisfunction may be activated ordeactivated in the Info-Display.Vehicle personalisation 3 98.

Fault in radio remote controlsystem

Unlocking

Manually unlock the driver's door byturning the key in the lock. Switch onthe ignition and press the centrallocking button c to unlock thepassenger door, load compartmentand fuel filler flap.By switching on the ignition, the anti-theft locking system is deactivated.

LockingManually lock the driver's door byturning the key in the lock.

Fault in central locking system

UnlockingManually unlock the driver's door byturning the key in the lock. Thepassenger door can be opened bypulling the interior handle twice. Theload compartment and fuel filler flapcannot be opened.To deactivate the anti-theft lockingsystem, switch on the ignition 3 25.

LockingPress inside locking knob ofpassenger door. Then close thedriver's door and lock it from theoutside with the key. The fuel filler flapand tailgate cannot be locked.

Automatic lockingThis security feature can beconfigured to automatically lockdoors, load compartment and fuelfiller flap as soon as a certain speedis exceeded.Additionally, it is configurable tounlock the driver's door or both doorsafter the ignition is switched off andthe ignition key is removed.


Settings can be changed in theInfo-Display.Vehicle personalisation 3 98.The settings can be saved for the keybeing used 3 21.

DoorsLoad compartmentTailgate

Opening

Press the brand emblem at thebottom half to unlock and open thetailgate.

Closing

Use interior handle.Do not press the emblem whilstclosing as this will unlock the tailgateagain.Central locking system 3 22.

General hints for operatingtailgate

9 Danger

Do not drive with the tailgate openor ajar, e.g. when transportingbulky objects, since toxic exhaust


gases, which cannot be seen orsmelled, could enter the vehicle.This can cause unconsciousnessand even death.

Caution

Before opening the tailgate, checkoverhead obstructions, e.g. agarage door, to avoid damage tothe tailgate. Always check themoving area above and behind thetailgate.

NoticeThe installation of certain heavyaccessories onto the tailgate mayaffect its ability to remain open.

Vehicle securityAnti-theft locking system

9 Warning

Do not use the system if there arepeople in the vehicle! The doorscannot be unlocked from theinside.

The system deadlocks all the doors.All doors must be closed otherwisethe system cannot be activated.If the ignition was on, the driver's doormust be opened and closed once sothat the vehicle can be secured.Unlocking the vehicle disables themechanical anti-theft locking system.This is not possible with the centrallocking button in the passengercompartment.

Activating

Press e on the radio remote controltwice within five seconds.

Anti-theft alarm systemThe anti-theft alarm system iscombined with the central lockingsystem.It monitors:● doors, tailgate, bonnet● ignition


Activation● Self-activated 30 seconds after

locking the vehicle by pressing eonce.

● Directly by pressing e twicewithin five seconds.

Status LED

Status LED is integrated in the sensoron top of the instrument panel.

Status during the first 30 seconds ofanti-theft alarm system activation:LED illuminates : test, arming delayLED flashesquickly

: doors, tailgate orbonnet notcompletely closed,or system fault

Status after system is armed:LED flashesslowly

: system is armed

Seek the assistance of a workshop inthe event of faults.

DeactivationUnlocking the vehicle by pressing cdeactivates anti-theft alarm system.The system is not deactivated byunlocking the driver's door with thekey or with the central locking buttonin the passenger compartment.

AlarmWhen triggered, the alarm hornsounds and the hazard warning lightsflash simultaneously. The numberand duration of alarm signals arestipulated by legislation.

The alarm can be silenced bypressing any button on the radioremote control or by switching on theignition.The anti-theft alarm system can onlybe deactivated by pressing c on theradio remote control or by switchingon the ignition.A triggered alarm, which has not beeninterrupted by the driver, will beindicated by the hazard warninglights. They will flash quickly threetimes when the vehicle is unlockedwith the radio remote control.Vehicle messages 3 95.

ImmobiliserThe system is part of the ignitionswitch and checks whether thevehicle is allowed to be started withthe key being used.The immobiliser is activatedautomatically after the key has beenremoved from the ignition switch.


If the control indicator d flashes whenthe ignition is on, there is a fault in thesystem; the engine cannot be started.Switch off the ignition and repeat thestart attempt.If the control indicator continuesflashing, attempt to start the engineusing the spare key and seek theassistance of a workshop.NoticeThe immobiliser does not lock thedoors. You should always lock thevehicle after leaving it.Switch on the anti-theft alarmsystem 3 22, 3 25.

Control indicator d 3 88.

Exterior mirrorsConvex shapeThe convex exterior mirror containsan aspherical area and reduces blindspots. The shape of the mirror makesobjects appear smaller, which willaffect the ability to estimatedistances.

Electric adjustment

Select the relevant exterior mirror byturning the control to left (L) or right(R). Then swivel the control to adjustthe mirror.

In position 0 no mirror is selected.

Folding mirrorsFor pedestrian safety, the exteriormirrors will swing out of their normalmounting position if they are struckwith sufficient force. Reposition themirror by applying slight pressure tothe mirror housing.

Parking positionThe exterior mirrors can be folded inby pressing gently on the outer edgeof the housing, e.g. when in aconfined parking situation.


Heated mirrors

Operated by pressing Ü.Heating works with the enginerunning and is switched offautomatically after a short time.

Interior mirrorsManual anti-dazzle

To reduce dazzle, adjust the lever onthe underside of the mirror housing tothe front or rear. Lever in the middleposition is the normal driving position.Versions with illuminated starlightpanelWhen the starlight panel isilluminated, adjust the lever to thefront. Starlight panel 3 109.

Automatic anti-dazzle

Dazzle from following vehicles atnight is automatically reduced.


WindowsWindscreenWindscreen stickersDo not attach stickers, e.g. toll roadstickers or similar, on the windscreenin the area of the interior mirror.Otherwise the detection zone of thesensor in the mirror housing could berestricted.

Power windows

9 Warning

Take care when operating thepower windows. Risk of injury,particularly to children.Be careful when closing thewindows. Ensure that nothingbecomes trapped in them as theymove.

Switch on ignition to operate powerwindows.Retained power off 3 124.

Operate the switch for the respectivewindow by pushing to open or pullingto close.Pushing or pulling gently to the firstdetent: window moves up or down aslong as the switch is operated.Pushing or pulling firmly to the seconddetent then releasing: window movesup or down automatically with safetyfunction enabled. To stop movement,operate the switch once more in thesame direction.

Safety functionIf the window glass encountersresistance above the middle of thewindow during automatic closing, it isimmediately stopped and openedagain.

Override safety functionIn the event of closing difficulties dueto frost or the like, switch on theignition, then pull the switch to the firstdetent and hold. The window movesup without safety function enabled.To stop movement, release theswitch.

Operating windows from outsideThe windows can be operatedremotely from outside the vehicle.


Press and hold c to open windows.Press and hold e to close windows.Release button to stop windowmovement.If the windows are fully opened orclosed, the hazard warning lights willflash twice.

OverloadIf the windows are repeatedlyoperated within short intervals, thewindow operation is disabled forsome time.

Initialising the power windowsIf the windows cannot be closedautomatically (e.g. afterdisconnecting the vehicle battery), awarning message or a warning codeis displayed in the Driver InformationCentre.Vehicle messages 3 95.Activate the window electronics asfollows:1. Close the doors.2. Switch on the ignition.3. Pull switch until the window is

closed and keep pulling foradditional two seconds.

4. Repeat for each window.

Heated rear window

Operated by pressing Ü.Heating works with the enginerunning and is switched offautomatically after a short time.

Sun visorsThe sun visors can be folded down orswivelled to the side to preventdazzling.The integral mirrors should be closedwhen driving.A ticket holder is located on thebackside of the sun visor.


RoofSunroofFoldable power sunroof

9 Warning

Take care when operating thesunroof. Risk of injury, particularlyto children.Keep a close watch on themovable parts when operatingthem. Ensure that nothingbecomes trapped in them as theymove.

Operable with ignition on (position 2)3 124.The foldable power sunroof can beopened and closed while driving up toa speed of 87 mph.Retained power off 3 124.

Switch can be operated in two ways:short press for automatic run and holddepressed for manual run.

OpenShort press on >: sunroof opensautomatically up to end position. Tostop movement operate switch oncemore.Hold > depressed: sunroof opens aslong as switch is operated.

CloseShort press on <: sunroof closesautomatically up to a gap of approx.30 cm for safety reasons. Followinghold < depressed to close the

sunroof completely. To stopmovement during automatic runoperate switch once more.Hold < depressed: sunroof closes aslong as switch is operated.

Glass panelSunblind

Press the button in the handle to openthe sunblind and guide it backwards.It rolls up automatically.No intermediate positions arepossible.To close, draw the sunblind to thefront and allow the button to engage.

32 Seats, restraints

Seats, restraints

Head restraints ............................ 32Front seats ................................... 33

Seat position .............................. 33Seat adjustment ........................ 34Seat folding ............................... 35Heating ...................................... 36

Seat belts ..................................... 37Three-point seat belt ................. 38

Airbag system .............................. 39Front airbag system ................... 42Side airbag system .................... 43Curtain airbag system ............... 43Airbag deactivation .................... 44

Child restraints ............................. 45Child restraint systems .............. 45Child restraint installationlocations ................................... 47

ISOFIX child restraint systems . . 50Top-tether fastening eyes .......... 50

Head restraints

Position

9 Warning

Only drive with the head restraintset to the proper position.

The upper edge of the head restraintshould be at upper head level. If thisis not possible for extremely tallpeople, set to highest position, andset to lowest position for small people.

Adjustment

Front head restraints, heightadjustment

Press release button, adjust height,engage.

Seats, restraints 33

Rear head restraints, heightadjustment

Pull the head restraint upwards andlet engage. To move downwards,press the catch to release and pushthe head restraint downwards.

Removal of rear head restraintE.g. when using a child restraintsystem 3 45.

Press both catches, pull the headrestraint upwards and remove.Place the head restraint in a net bagand secure the underside of the bagwith Velcro fasteners to the loadcompartment floor. A suitable net bagis available from your workshop.

Front seatsSeat position

9 Warning

Only drive with the seat correctlyadjusted.

9 Danger

Do not sit nearer than 25 cm fromthe steering wheel, to permit safeairbag deployment.

9 Warning

Never adjust seats while driving asthey could move uncontrollably.

9 Warning

Never store any objects under theseats.


● Sit with buttocks as far backagainst the backrest as possible.Adjust the distance between theseat and the pedals so that legsare slightly angled when fullypressing the pedals. Slide thefront passenger seat as far backas possible.

● Set seat height high enough tohave a clear field of vision on allsides and of all displayinstruments. There should be atleast one hand of clearancebetween head and the roofframe. Your thighs should restlightly on the seat withoutpressing into it.

● Sit with shoulders as far backagainst the backrest as possible.Set the backrest rake so that it ispossible to easily reach thesteering wheel with arms slightlybent. Maintain contact betweenshoulders and the backrest whenturning the steering wheel. Donot angle the backrest too farback. We recommend amaximum rake of approx. 25°.

● Adjust seat and steering wheel ina way that the wrist rests on topof the steering wheel while thearm is fully extended andshoulders on the backrest.

● Adjust the steering wheel 3 70.● Adjust the head restraint 3 32.

Seat adjustmentDrive only with engaged seats andbackrests.

Longitudinal adjustment

Pull handle, slide seat, releasehandle. Try to move the seat back andforth to ensure that the seat is lockedin place.


Backrest inclination

Turn handwheel to adjust inclination.Do not lean on backrest whileadjusting.

Seat height

Lever pumping motionup : seat higherdown : seat lower

Seat folding

Pull release lever towards the frontand fold backrest forwards. Thenslide seat forwards to the stop.To restore, slide the seat backwardsto the stop. Lift backrest to uprightposition without operating the releaselever. Allow backrest to engage.

9 Warning

When folding up, ensure that theseat is securely locked in positionbefore driving. Failure to do somay result in personal injury in theevent of heavy braking or collision.


The memory function allows the seatto engage in its original position afterfolding.Do not operate backrest adjusterhandwheel when backrest is foldedforwards.

Caution

When seat height is in the highestposition, push head restraintsdown and fold up sun visors beforefolding backrest forwards.

Sport seat folding

Remove seat belt from belt mount onthe backrest.Pull release lever located on thebackrest, fold backrest forwards andrelease lever. Slide seat forwards tothe stop.To restore, slide the seat backwardsto the stop. Lift backrest to uprightposition without operating the releaselever. Allow backrest to engage.

9 Warning

When folding up, ensure that theseat is securely locked in positionbefore driving. Failure to do somay result in personal injury in theevent of heavy braking or collision.

The memory function allows the seatto engage in its original position afterfolding.Do not operate backrest adjusterhandwheel when backrest is foldedforwards.

Heating

Activate seat heating by pressing ßfor the respective front seat.Activation is indicated by the LED inthe button.Pressing ß once more deactivatesseat heating.Seat heating is operational whenengine is running.During an Autostop seat heating isalso operational.Stop-start system 3 126.


Seat belts

The seat belts are locked duringheavy acceleration or deceleration ofthe vehicle holding the occupants inthe sitting position. Therefore the riskof injury is considerably reduced.

9 Warning

Fasten seat belt before each trip.In the event of an accident, peoplenot wearing seat belts endangertheir fellow occupants andthemselves.

Seat belts are designed to be used byonly one person at a time. Childrestraint system 3 45.Periodically check all parts of the beltsystem for damage, pollution andproper functionality.Have damaged componentsreplaced. After an accident, have thebelts and triggered belt pretensionersreplaced by a workshop.NoticeMake sure that the belts are notdamaged by shoes or sharp-edgedobjects or are trapped. Prevent dirtfrom getting into the belt retractors.

Seat belt reminderEach seat is equipped with a seat beltreminder, indicated for driver seat ascontrol indicator X in the tachometer3 83, for front passenger seat ascontrol indicator k in the centreconsole 3 81, and for rear seats bysymbols X in the Driver InformationCentre 3 88.

Belt force limitersOn the front seats, stress on the bodyis reduced by the gradual release ofthe belt during a collision.

Belt pretensionersIn the event of a head-on or rear-endcollision of a certain severity, the frontseat belts are tightened.

9 Warning

Incorrect handling (e.g. removal orfitting of belts) can trigger the beltpretensioners.

Deployment of the belt pretensionersis indicated by continuous illuminationof control indicator v 3 84.Triggered belt pretensioners must bereplaced by a workshop. Beltpretensioners can only be triggeredonce.NoticeDo not affix or install accessories orother objects that may interfere withthe operation of the belt


pretensioners. Do not make anymodifications to belt pretensionercomponents as this will invalidatethe vehicle type approval.

Three-point seat beltFasten

Withdraw the belt from the retractor,guide it untwisted across the bodyand insert the latch plate into thebuckle. Tighten the lap belt regularlywhile driving by pulling the shoulderbelt.Sport seat: Feed seat belt throughbelt mount on backrest whenfastening seat belt.

Loose or bulky clothing prevents thebelt from fitting snugly. Do not placeobjects such as handbags or mobilephones between the belt and yourbody.

9 Warning

The belt must not rest against hardor fragile objects in the pockets ofyour clothing.

Seat belt reminder X 3 83.

Unfasten

To release belt, press red button onbelt buckle.


Using the seat belt while pregnant

9 Warning

The lap belt must be positioned aslow as possible across the pelvisto prevent pressure on theabdomen.

Airbag systemThe airbag system consists of anumber of individual systemsdepending on the scope ofequipment.When triggered, the airbags inflatewithin milliseconds. They also deflateso quickly that it is often unnoticeableduring the collision.

9 Warning

If handled improperly the airbagsystems can be triggered in anexplosive manner.

NoticeThe airbag systems and beltpretensioner control electronics arelocated in the centre console area.Do not put any magnetic objects inthis area.Do not affix any objects onto theairbag covers and do not cover themwith other materials.Each airbag is triggered only once.Have deployed airbags replaced bya workshop. Furthermore, it may be

necessary to have the steeringwheel, the instrument panel, parts ofthe panelling, the door seals,handles and the seats replaced.Do not make any modifications tothe airbag system as this willinvalidate the vehicle type approval.

When the airbags inflate escaping hotgases may cause burns.

FaultIf there is a fault in the airbag system,the control indicator v illuminates anda message or a warning codeappears in the Driver InformationCentre. The system is notoperational.Have the cause of the fault remediedby a workshop.Control indicator for airbag systems3 84.

Child restraint systems on frontpassenger seat with airbagsystemsWarning according to ECE R94.02:


EN: NEVER use a rearward-facingchild restraint on a seat protected byan ACTIVE AIRBAG in front of it;DEATH or SERIOUS INJURY to theCHILD can occur.DE: Nach hinten gerichteteKindersitze NIEMALS auf einem Sitzverwenden, der durch einen davorbefindlichen AKTIVEN AIRBAGgeschützt ist, da dies den TOD oderSCHWERE VERLETZUNGEN DESKINDES zur Folge haben kann.FR: NE JAMAIS utiliser un sièged'enfant orienté vers l'arrière sur unsiège protégé par un COUSSINGONFLABLE ACTIF placé devant lui,

sous peine d'infliger desBLESSURES GRAVES, voireMORTELLES à l'ENFANT.ES: NUNCA utilice un sistema deretención infantil orientado haciaatrás en un asiento protegido por unAIRBAG FRONTAL ACTIVO. Peligrode MUERTE o LESIONES GRAVESpara el NIÑO.RU: ЗАПРЕЩАЕТСЯустанавливать детскоеудерживающее устройство лицомназад на сиденье автомобиля,оборудованном фронтальнойподушкой безопасности, еслиПОДУШКА НЕ ОТКЛЮЧЕНА! Этоможет привести к СМЕРТИ илиСЕРЬЕЗНЫМ ТРАВМАМРЕБЕНКА.NL: Gebruik NOOIT een achterwaartsgericht kinderzitje op een stoel meteen ACTIEVE AIRBAG ervoor, omDODELIJK of ERNSTIG LETSEL vanhet KIND te voorkomen.DA: Brug ALDRIG en bagudvendtautostol på et forsæde med AKTIVAIRBAG, BARNET kan komme iLIVSFARE eller komme ALVORLIGTTIL SKADE.

SV: Använd ALDRIG en bakåtvändbarnstol på ett säte som skyddas meden framförvarande AKTIV AIRBAG.DÖDSFALL eller ALLVARLIGASKADOR kan drabba BARNET.FI: ÄLÄ KOSKAAN sijoita taaksepäinsuunnattua lasten turvaistuintaistuimelle, jonka edessä onAKTIIVINEN TURVATYYNY, LAPSIVOI KUOLLA tai VAMMAUTUAVAKAVASTI.NO: Bakovervendtbarnesikringsutstyr må ALDRI brukespå et sete med AKTIVKOLLISJONSPUTE foran, da det kanføre til at BARNET utsettes forLIVSFARE og fare for ALVORLIGESKADER.PT: NUNCA use um sistema deretenção para crianças voltado paratrás num banco protegido com umAIRBAG ACTIVO na frente domesmo, poderá ocorrer a PERDA DEVIDA ou FERIMENTOS GRAVES naCRIANÇA.IT: Non usare mai un sistema disicurezza per bambini rivoltoall'indietro su un sedile protetto da


AIRBAG ATTIVO di fronte ad esso:pericolo di MORTE o LESIONIGRAVI per il BAMBINO!EL: ΠΟΤΕ μη χρησιμοποιείτε παιδικόκάθισμα ασφαλείας με φορά προς ταπίσω σε κάθισμα που προστατεύεταιαπό μετωπικό ΕΝΕΡΓΟ ΑΕΡΟΣΑΚΟ,διότι το παιδί μπορεί να υποστείΘΑΝΑΣΙΜΟ ή ΣΟΒΑΡΟΤΡΑΥΜΑΤΙΣΜΟ.PL: NIE WOLNO montować fotelikadziecięcego zwróconego tyłem dokierunku jazdy na fotelu, przedktórym znajduje się WŁĄCZONAPODUSZKA POWIETRZNA.Niezastosowanie się do tegozalecenia może być przyczynąŚMIERCI lub POWAŻNYCHOBRAŻEŃ u DZIECKA.TR: Arkaya bakan bir çocuk emniyetsistemini KESİNLİKLE önünde birAKTİF HAVA YASTIĞI ilekorunmakta olan bir koltuktakullanmayınız. ÇOCUK ÖLEBİLİRveya AĞIR ŞEKİLDEYARALANABİLİR.UK: НІКОЛИ не використовуйтесистему безпеки для дітей, щовстановлюється обличчям назад,

на сидінні з УВІМКНЕНОЮПОДУШКОЮ БЕЗПЕКИ, інакше цеможе призвести до СМЕРТІ чиСЕРЙОЗНОГО ТРАВМУВАННЯДИТИНИ.HU: SOHA ne használjon hátrafelénéző biztonsági gyerekülést előlrőlAKTÍV LÉGZSÁKKAL védett ülésen,mert a GYERMEK HALÁLÁT vagyKOMOLY SÉRÜLÉSÉT okozhatja.HR: NIKADA nemojte koristiti sustavzadržavanja za djecu okrenut premanatrag na sjedalu s AKTIVNIMZRAČNIM JASTUKOM ispred njega,to bi moglo dovesti do SMRTI iliOZBILJNJIH OZLJEDA za DIJETE.SL: NIKOLI ne nameščajte otroškegavarnostnega sedeža, obrnjenega vnasprotni smeri vožnje, na sedež zAKTIVNO ČELNO ZRAČNOBLAZINO, saj pri tem obstajanevarnost RESNIH ali SMRTNIHPOŠKODB za OTROKA.SR: NIKADA ne koristiti bezbednosnisistem za decu u kome su decaokrenuta unazad na sedištu saAKTIVNIM VAZDUŠNIM

JASTUKOM ispred sedišta zato štoDETE može da NASTRADA ili da seTEŠKO POVREDI.MK: НИКОГАШ не користете детскоседиште свртено наназад наседиште заштитено со АКТИВНОВОЗДУШНО ПЕРНИЧЕ пред него,затоа што детето може ДА ЗАГИНЕили да биде ТЕШКО ПОВРЕДЕНО.BG: НИКОГА не използвайтедетска седалка, гледаща назад,върху седалка, която е защитеначрез АКТИВНА ВЪЗДУШНАВЪЗГЛАВНИЦА пред нея - може дасе стигне до СМЪРТ илиСЕРИОЗНО НАРАНЯВАНЕ наДЕТЕТО.RO: Nu utilizaţi NICIODATĂ un scaunpentru copil îndreptat spre partea dinspate a maşinii pe un scaun protejatde un AIRBAG ACTIV în faţa sa;acest lucru poate duce la DECESULsau VĂTĂMAREA GRAVĂ aCOPILULUI.CS: NIKDY nepoužívejte dětskýzádržný systém instalovaný protisměru jízdy na sedadle, které jechráněno před sedadlem AKTIVNÍM


AIRBAGEM. Mohlo by dojít kVÁŽNÉMU PORANĚNÍ nebo ÚMRTÍDÍTĚTE.SK: NIKDY nepoužívajte detskúsedačku otočenú vzad na sedadlechránenom AKTÍVNYM AIRBAGOM,pretože môže dôjsť k SMRTI aleboVÁŽNYM ZRANENIAM DIEŤAŤA.LT: JOKIU BŪDU nemontuokite atgalatgręžtos vaiko tvirtinimo sistemossėdynėje, prieš kurią įrengta AKTYVIORO PAGALVĖ, nes VAIKAS GALIŽŪTI arba RIMTAI SUSIŽALOTI.LV: NEKĀDĀ GADĪJUMĀneizmantojiet uz aizmuguri vērstubērnu sēdeklīti sēdvietā, kas tiekaizsargāta ar tās priekšā uzstādītuAKTĪVU DROŠĪBAS SPILVENU, jopretējā gadījumā BĒRNS var gūtSMAGAS TRAUMAS vai IET BOJĀ.ET: ÄRGE kasutage tahapoolesuunatud lapseturvaistet istmel, milleees on AKTIIVSE TURVAPADJAGAkaitstud iste, sest see võibpõhjustada LAPSE SURMA võiTÕSISE VIGASTUSE.

MT: QATT tuża trażżin għat-tfal lijħares lejn in-naħa ta’ wara fuq sitprotett b’AIRBAG ATTIV quddiemu;dan jista’ jikkawża l-MEWT jewĠRIEĦI SERJI lit-TFAL.Beyond the warning required byECE R94.02, for safety reasons aforward-facing child restraint systemmust only be used subject to theinstructions and restrictions in thetable 3 47.The airbag label is located on bothsides of the front passenger sun visor.Airbag deactivation 3 44.

Front airbag systemThe front airbag system consists ofone airbag in the steering wheel andone in the instrument panel on thefront passenger side. The location isidentified by the word AIRBAG.The front airbag system is triggered inthe event of a front-end impact of acertain severity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and head ofthe front seat occupantsconsiderably.

9 Warning

Optimum protection is onlyprovided when the seat is in theproper position.Seat position 3 33.Keep the area in which the airbaginflates clear of obstructions.


Fit the seat belt correctly andengage securely. Only then is theairbag able to protect.

Side airbag system

The side airbag system consists of anairbag in each front seat backrest.The location is identified by the wordAIRBAG.The side airbag system is triggered inthe event of a side impact of a certainseverity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and pelvis inthe event of a side-on collisionconsiderably.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.

NoticeOnly use protective seat covers thathave been approved for the vehicle.Be careful not to cover the airbags.

Curtain airbag systemThe curtain airbag system consists ofan airbag in the roof frame on eachside. The location is identified by theword AIRBAG on the roof pillars.The curtain airbag system is triggeredin the event of a side-on impact of acertain severity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the head in the event of aside-on impact considerably.


9 Warning

Keep the area in which the airbaginflates clear of obstructions.The hooks on the handles in theroof frame are only suitable forhanging up light articles ofclothing, without coat hangers. Donot keep any items in theseclothes.

Airbag deactivationThe front passenger airbag systemmust be deactivated for child restraintsystem on the passenger seataccording to the instructions in thetable 3 47. The side airbag andcurtain airbag systems, the beltpretensioners and all driver airbagsystems will remain active.

Use the ignition key to choose theswitch position:*OFF : front passenger airbag is

deactivated and will notinflate in the event of acollision. Control indicator*OFF illuminatescontinuously in the centreconsole

VON : front passenger airbag isactive

9 Danger

Deactivate passenger airbag onlyin combination with the use of achild restraint system, subject tothe instructions and restrictions inthe table 3 47.Otherwise, there is a risk of fatalinjury for a person occupying aseat with a deactivated frontpassenger airbag.


If the control indicator V illuminatesfor approx. 60 seconds after theignition is switched on, the frontpassenger airbag system will inflatein the event of a collision.If both control indicators areilluminated at the same time, there isa system failure. The status of thesystem is not discernible, thereforeno person is allowed to occupy thefront passenger seat. Contact aworkshop immediately.Change status only when the vehicleis stopped with the ignition off.Status remains until the next change.Control indicator for airbagdeactivation 3 84.

Child restraintsChild restraint systemsWe recommend the followingVauxhall child restraint system whichare tailored specifically to the vehicle:● Group 0, Group 0+

VAUXHALL Baby cradle, with orwithout ISOFIX base, for childrenup to 13 kg.

● Group IFAIR G 0/1 S ISOFIX, for childrenfrom 9 kg to 13 kg in this group.VAUXHALL Duo, for childrenfrom 13 kg to 18 kg in this group.

● Group II, Group IIIVAUXHALL Kid, VAUXHALLKidfix, TAKATA MAXI 2/3 forchildren from 15 kg up to 36 kg.

When a child restraint system is beingused, pay attention to the followingusage and installation instructionsand also those supplied with the childrestraint system.

Always comply with local or nationalregulations. In some countries, theuse of child restraint systems isforbidden on certain seats.

9 Danger

If using a rear-facing child restraintsystem on the front passengerseat, the airbag system for thefront passenger seat must bedeactivated. This also applies tocertain forward-facing childrestraint systems as indicated inthe table 3 47.

Airbag deactivation 3 44.Airbag label 3 39.

Selecting the right systemThe rear seats are the mostconvenient location to fasten a childrestraint system.Children should travel facingrearwards in the vehicle as long aspossible. This ensures that the child'sbackbone, which is still very weak, isunder less strain in the event of anaccident.


Suitable are restraint systems thatcomply with valid UN ECEregulations. Check local laws andregulations for mandatory use of childrestraint systems.Ensure that the child restraint systemto be installed is compatible with thevehicle type.Ensure that the mounting location ofthe child restraint system within thevehicle is correct, see followingtables.Allow children to enter and exit thevehicle only on the side facing awayfrom the traffic.When the child restraint system is notin use, secure the seat with a seat beltor remove it from the vehicle.NoticeDo not affix anything on the childrestraint systems and do not coverthem with any other materials.A child restraint system which hasbeen subjected to stress in anaccident must be replaced.


Child restraint installation locationsPermissible options for fitting a child restraint system

Weight and age classOn front passenger seat

On rear seatsactivated airbag deactivated airbag

Group 0: up to 10 kgor approx. 10 months

X U1 U*

Group 0+: up to 13 kgor approx. 2 years

X U1 U*

Group I: 9 to 18 kgor approx. 8 months to 4 years

X U1 U2 *

Group II: 15 to 25 kgor approx. 3 to 7 years

U ** X U *

Group III: 22 to 36 kgor approx. 6 to 12 years

U ** X U *

48 Seats, restraints1 : if the child restraint system is being secured using a three-point seat belt, adjust seat backrest inclination to a vertical

position to ensure that the belt is tight on the buckle side. Move seat height adjustment in the uppermost position.2 : remove rear head restraint when using child restraint systems in this group 3 32* : move the respective front seat ahead of the child restraint system to one of the foremost adjustment positions** : move the front passenger seat to the rearmost adjustment position. Move seat height adjustment to the uppermost

position and the headrest to the lowest position. Adjust seat backrest inclination as far as necessary to a verticalposition to ensure that vehicle seat belt runs forwards from the upper anchorage point

U : universal suitability in conjunction with three-point seat beltX : no child restraint system permitted in this weight class

Permissible options for fitting an ISOFIX child restraint system

Weight class Size class Fixture On front passenger seat On rear seats

Group 0: up to 10 kgor approx. 10 months

E ISO/R1 X IL *

Group 0+: up to 13 kgor approx. 2 years

E ISO/R1 X IL *

D ISO/R2 X X

C ISO/R3 X X

Group I: 9 to 18 kgor approx. 8 months to 4 years

D ISO/R2 X X

C ISO/R3 X X

B ISO/F2 X IL, IUF**

B1 ISO/F2X X IL, IUF**

A ISO/F3 X IL, IUF**


Weight class Size class Fixture On front passenger seat On rear seats

Group II: 15 to 25 kgor approx. 3 to 7 years

X IL

Group III: 22 to 36 kgor approx. 6 to 12 years

X IL

IL : suitable for particular ISOFIX restraint systems of the "specific-vehicle", "restricted" or "semi-universal" categories.The ISOFIX restraint system must be approved for the specific vehicle type

IUF : suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight classX : no ISOFIX child restraint system approved in this weight class* : move the respective front seat ahead of the child restraint system to one of the foremost adjustment positions** : remove respective rear head restraint when using child restraint systems in this size class 3 32

ISOFIX size class and seat deviceA – ISO/F3 : forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kgB – ISO/F2 : forward-facing child restraint system for smaller children in the weight class 9 to 18 kgB1 – ISO/F2X : forward-facing child restraint system for smaller children in the weight class 9 to 18 kgC – ISO/R3 : rear-facing child restraint system for children of maximum size in the weight class up to 18 kgD – ISO/R2 : rear-facing child restraint system for smaller children in the weight class up to 18 kgE – ISO/R1 : rear-facing child restraint system for young children in the weight class up to 13 kg


ISOFIX child restraintsystemsFasten vehicle-approved ISOFIXchild restraint systems to the ISOFIXmounting brackets. Specific vehicleISOFIX child restraint systempositions are marked in the table byIL.

ISOFIX mounting brackets areindicated by the ISOFIX logo on thebackrest.The vehicle is equipped with guides inthe backrests to support theinstallation of the child restraintsystem. Open the flaps of the guidesto mount a child restraint system.

Remove rear head restraint beforemounting a child restraint system, ifrequired 3 47.

Top-tether fastening eyesThe vehicle has two fastening eyeson the backside of the rear seats.Top-Tether fastening eyes aremarked with the symbol : for a childseat.

In addition to the ISOFIX mounting,fasten the Top-Tether strap to theTop-Tether fastening eyes.

ISOFIX child restraint systems ofuniversal category positions aremarked in the table by IUF.Remove rear head restraint beforemounting a child restraint system, ifrequired 3 47.

Storage 51

Storage

Storage compartments ................ 51Glovebox ................................... 51Cupholders ................................ 51Front storage ............................. 52Rear carrier system ................... 53

Load compartment ....................... 62Rear storage .............................. 63Load compartment cover ........... 64Rear floor storage cover ............ 64Lashing eyes ............................. 66Warning triangle ........................ 66First aid kit ................................. 67

Roof rack system ......................... 67Roof rack ................................... 67

Loading information ..................... 67

Storage compartments

9 Warning

Do not store heavy or sharpobjects in the storagecompartments. Otherwise, thestorage compartment lid couldopen and vehicle occupants couldbe injured by objects being thrownaround in the event of hardbraking, a sudden change indirection or an accident.

Glovebox

Pull lever to open the glovebox cover.The glovebox features a coin holderand an adapter for the locking wheelbolts.The glovebox should be closed whilstdriving.

Cupholders

Cupholders are located in the consolebetween the front seats. They aredesigned for cups of different sizes.

52 Storage

Door pockets in both doors aredesigned to carry bottles.

Additional cupholders or bottleholders are located in the rear sidepanels.

Flexible cupholder strap

A movable rubber strap is located inthe storage compartment in front ofthe gear selector lever. Pull out thestrap to fix a cup or ashtray.

Front storage

Storage compartments are locatedbelow the light switch, in the centreconsole in front of the gear selectorlever, in the door pockets and in theside panels near the rear seats.

Storage 53

Rear carrier systemRear carrier system for twobicycles

The rear carrier system (Flex-Fixsystem) allows one bicycle to beattached to a pull-out carrierintegrated into the vehicle floor. It ispossible to attach one further bicycleon an adapter. The transportation ofother objects is not permitted.The maximum load of the rear carriersystem is 50 kg with attached adapterand 30 kg without attached adapter.This allows the attachment of an

electrically-powered bicycle to thepull-out carrier. The maximum load onthe adapter is 20 kg.The wheelbase of a bicycle must notexceed 1.15 metres. Otherwise thesecure fastening of a bicycle is notpossible.If not in use, the carrier system mustbe slid back into the vehicle floor.There must not be any objects on thebicycles that could become looseduring transportation.

Caution

If the rear carrier system isextended and the vehicle is fullyloaded, the chassis clearance willbe reduced.Drive carefully whenever the roadhas a strong inclination or whendriving over a ramp, bump, etc.

Caution

Consult your bicycle dealer beforeattaching bicycles with carbonframes. The bicycles might getdamaged.

ExtendingOpen the tailgate.

9 Warning

No-one should be in the extensionzone of the rear carrier system,risk of injury.

54 Storage

Pull release lever up. The systemdisengages and travels quickly out ofthe bumper.

Completely pull out the rear carriersystem until you hear it engage.Ensure that it is not possible to pushin the rear carrier system withoutpulling the release lever again.

9 Warning

It is only permissible to fit objectsto the rear carrier system if thesystem has been correctlyengaged. If the rear carrier systemwill not engage correctly, do not fit

objects to the system and slide thesystem back. Seek the assistanceof a workshop.

Unfold number plate light

Lift the number plate light and fold itbackwards.

Fold out tail lamps

Swivel hinges of both tail lampsbackwards as far as it will go.

Storage 55

Swivel both tail lamps backwards asfar as it will go.

Fold out wheel recess

Remove strap and fold out the wheelrecess.

Lock the rear carrier system

Remove strap and swivel bothclamping levers sideways as far as itwill go.Otherwise safe functionality is notguaranteed.

Assembling the bicycle rack

Lift the rack at the rear (1) and pull itbackwards.Fold up the rack (2).

56 Storage

Push down the rack (1) and swivelhandle (2) backwards to engage.

Press button (1) and remove left partof rack (2).

Press button (1) and insert left part ofrack into the right part (2).

Attaching the adapterWhen carrying two bicycles, theadapter must be fixed beforeattaching the first bicycle.

1. Apply the adapter to the rearcarrier system as shown in theillustration.

2. Turn the lever (1) forwards andhold, then lower the adapter (2) atthe rear.

3. Release lever and check if theadapter is engaged securely.

Storage 57

4. Guide the strap attached to theadapter underneath the lever forfolding back the rear carriersystem. Fasten the strap.

Attaching the first bicycle

1. Rotate the pedals into position asshown in the illustration and putthe bicycle on the wheel recess.Make sure that the bicycle standscentrally on the wheel recesses.

2. Attach the short mounting bracketto the bicycle frame. Turn theknob clockwise to fasten.

3. Secure both bicycle wheels to thewheel recesses using the strapretainers.

4. Check the bicycle to make sure itis secure.

Caution

Ensure gap between bicycle andvehicle is at least 5 cm. Ifnecessary, loosen handlebar andswivel sideways.

Attaching the second bicycleThe attachment of a second bicycle issimilar to the attachment of the firstbicycle. Additionally, some stepsmust be considered:1. Always rotate the pedals into an

appropriate position beforeputting on the bicycle.

58 Storage

2. Position the bicycles on the rearcarrier system alternately alignedto the left and to the right.

3. Align the rear bicycle to the frontbicycle. The wheel hubs of thebicycles must not touch eachother.

4. Attach the rear bicycle with thelonger mounting bracket and thestrap retainers as described forthe front bicycle. The mountingbrackets should be fixed inparallel.

5. Additionally, secure both bicyclewheels of the rear bicycle to thewheel recesses using thetensioning straps.

It is recommended to attach awarning sign at the rearmost bicycle,to increase visibility.

Fold the rear carrier systembackwardsThe rear carrier system can be foldedbackwards to gain access to the loadcompartment.

● Without attached adapter:

Push the lever (1) to disengageand hold.Pull the rack (2) backwards tofold the rear carrier system.

● With attached adapter:

9 Warning

Take care when disengaging therear carrier system as it will tiltbackwards. Risk of injury.

Storage 59

Hold frame (1) of rear bicycle withone hand and pull the loop (2) todisengage.Hold rear bicycle with both handsand fold the rear carrier systembackwards.

To increase visibility, the tail lights ofthe vehicle are activated when therear carrier system is folded back.

9 Warning

When folding the rear carriersystem forwards again, take carethat the system is engagedsecurely.

Removing bicyclesUndo strap retainers on both bicycletyres.Turn knob anticlockwise and removemounting brackets.

Detaching adapter1. Fold in wheel recesses.

2. Unbutton the strap.

3. Turn the lever (1) forwards andhold.

4. Lift the adapter (2) at the rear andremove.

60 Storage

Disassembling the bicycle rack

Press button (1) and remove upperpart of rack (2).

Press button (1) and reinstall rack (2).

Arrange mounting bracket as shownin the illustration.Swivel handle (1) sideways todisengage and lift the rack (2).

Fold the rack backwards, then pushforwards until it stops (1).Press the rack down at the rear (2).

Fold in wheel recessFold in wheel recess. Fasten strap.

Stow the strap retainers accurately.

Storage 61

Unlock the rear carrier system

Swivel both clamping levers inwardsas far as it will go. Fasten strap.

Fold in tail lamps

First swivel tail lamps (1) forwards asfar as it will go.Then swivel hinges (2) forwards as faras it will go.

Fold in number plate light

Fold number plate light forwards.

Retracting the rear carrier system

Caution

Take care that all foldable parts,e.g. wheel recesses and mountingbrackets, are stowed accurately.Otherwise the rear carrier systemmight get damaged when trying toretract it.

62 Storage

Push the release lever up and hold.Lift the system slightly and push it intothe bumper until it engages.Release lever must return to originalposition.

9 Warning

If the system cannot be correctlyengaged, please seek theassistance of a workshop.

Load compartmentThe rear seat backrest is divided intotwo parts. Both parts can be foldeddown separately.

Load compartment extensionRemove the load compartment coverif necessary.Press the catch and push down thehead restraint.

Insert seat belt latch plate into sideholder to protect the belt againstdamage.

Pull the loop on one or both backrestsand fold them down onto the seatcushion.To fold up, raise the backrests intoupright position and let them engageaudibly.The backrests are properly engagedwhen the red marks on both releaseloops are not visible.

9 Warning

When folding up, ensure thatbackrests are securely locked inposition before driving. Failure to

Storage 63

do so may result in personal injuryor damage to load or vehicle in theevent of heavy braking or collision.

Hook for carrier bags

Use the hook at the right sidewall ofthe load compartment for hanging upcarrier bags. Maximum load: 5 kg.

Rear storageStorage boxA closable storage box is located inthe load compartment. The cover islockable by turning the knob. It mustbe locked while driving.To open, unlock and lift up the cover.To remove the cover, open it and slidesideways to the left.The box can be separated by adivider.The storage box cover can be loadedwith max. 20 kg.

RemovalTo gain access to emergencybreakdown equipment or for bulbreplacement of the tail lights, thestorage box must be removed:● Remove the load compartment

cover 3 64.● Fold down the rear backrests

3 62.● Open the storage box.

● Turn the lock hooks on both sidesto the rear and push down thelashing eyes in the recesses.

● Raise the storage box and placeit on the folded backrests.

● Remove the storage box out ofthe load compartment.

Installation● Place the storage box on the

folded backrests.● Lower the box in the load

compartment.● Open the storage box.

64 Storage

● Raise the lashing eyes on bothsides and turn the lock hooks tothe front to fix the box to thelashing eyes.

● Raise the rear backrests andinstall the load compartmentcover.

● Stow the suitcase with tyre repairkit in a chamber of the storagebox.

● Close and lock the cover.

Load compartment coverDo not place any objects on the cover.

Opening

Lift up the cover at the rear end. Itengages in a nearly vertical position.Further opening is possible. To close,move down the cover beyond theengage point.

Removing

Push cover upwards at the left andright from the lower side and remove.

FittingEngage cover by pushing into guideson both sides.

Rear floor storage coverRear floor cover

Lift up rear floor cover to gain accessto emergency breakdown equipment.Tools 3 182.

Subwoofer coverLift up rear part of floor cover to gainaccess to the warning triangle.When closing floor cover, ensure it isfixed with the Velcro fastener.

Storage 65

Removal

Remove floor cover to gain access toemergency breakdown equipmentand for bulb replacement of tail lights:● Lift up and fold the rear part to the

front.● Pull out the cover to the rear, it

will be lifted slightly by a guide.● Detach the cover from the load

compartment.

To gain access to the right cover inthe load compartment, e.g. for bulbreplacement, fold down rear rightbackrest and pull out the tool boxbeside the subwoofer.Bulb replacement 3 172.

Installation● Install the tool box if removed.● Place the floor cover in load

compartment.

● Move the floor cover slowly to thefront, taking care that the guidingbolts slide into the attachments ofthe load compartment, and allowthe floor cover to lower intoposition.

● Close the floor cover by foldingthe upper part to the rear, and fixit with the Velcro fastener.

● Fold up the rear backrests.

66 Storage

General hint

9 Warning

For safety reasons, stow all partsin the load compartment in itsposition, always drive with aclosed rear floor cover and, ifpossible, with folded up rearbackrests.Otherwise, vehicle occupantscould be injured by objects beingthrown around in the event ofsharp braking, a sudden change indirection or an accident.

Lashing eyes

The lashing eyes are designed tosecure items against slippage, e.g.using lashing straps or luggage net.

Warning triangle

The warning triangle is stowed withelastic straps in the loadcompartment below the tailgate.If the vehicle is equipped with astorage box in the load compartment,remove the storage box to gainaccess to the warning triangle 3 63.Version with subwoofer box

Lift up the rear part of the floor cover.Pull the handle to remove the warningtriangle.Rear floor storage cover 3 64.

Storage 67

First aid kit

Stow the first aid kit in the side panelstorage near the rear seats.

Roof rack systemRoof rackFor safety reasons and to avoiddamage to the roof, the vehicleapproved roof rack system isrecommended. For furtherinformation contact your workshop.Follow the installation instructionsand remove the roof rack when not inuse.

Mounting roof rackOpen the cover from each mountingpoint by using a coin.

Loading information

● Heavy objects in the loadcompartment should be placedagainst the seat backrests.Ensure that the backrests aresecurely engaged. If objects canbe stacked, heavier objectsshould be placed at the bottom.

● Secure objects with lashingstraps attached to the lashingeyes 3 66.

● Use the hook at the right sidewallof the load compartment forhanging up carrier bags.Maximum load: 5 kg.

68 Storage

● Secure loose objects in the loadcompartment to prevent themfrom sliding.

● When transporting objects in theload compartment, the backrestsof the rear seats must not beangled forward.

● Do not allow the load to protrudeabove the upper edge of thebackrests.

● Do not place any objects on theload compartment cover or theinstrument panel, and do notcover the sensor on top of theinstrument panel.

● The load must not obstruct theoperation of the pedals, parkingbrake and gear selector lever, orhinder the freedom of movementof the driver. Do not place anyunsecured objects in the interior.

● Do not drive with an open loadcompartment.

9 Warning

Always make sure that the load inthe vehicle is securely stowed.Otherwise objects can be thrownaround inside the vehicle andcause personal injury or damageto the load or vehicle.

● The payload is the differencebetween the permitted grossvehicle weight (see identificationplate 3 213) and the EC kerbweight.To calculate the payload, enterthe data for your vehicle in theweights table at the front of thismanual.The EC kerb weight includesweights for the driver (68 kg),luggage (7 kg) and all fluids (fueltank 90% full).Optional equipment andaccessories increase the kerbweight.

● Driving with a roof load increasesthe sensitivity of the vehicle tocross-winds and has a

detrimental effect on vehiclehandling due to the vehicle'shigher centre of gravity.Distribute the load evenly andsecure it properly with retainingstraps. Adjust the tyre pressureand vehicle speed according tothe load conditions. Check andretighten the straps frequently.Do not drive faster than 75 mph.The permissible roof load is50 kg. The roof load is thecombined weight of the roof rackand the load.

Instruments and controls 69

Instruments andcontrols

Controls ....................................... 70Steering wheel adjustment ........ 70Steering wheel controls ............. 70Heated steering wheel ............... 70Horn ........................................... 71Windscreen wiper/washer ......... 71Rear window wiper/washer ....... 73Outside temperature .................. 73Clock ......................................... 74Power outlets ............................. 76Inductive charging ..................... 76Cigarette lighter ......................... 77Ashtrays .................................... 77

Warning lights, gauges and indi‐cators ........................................... 78

Instrument cluster ...................... 78Speedometer ............................. 78Odometer .................................. 78Trip odometer ............................ 78Tachometer ............................... 78Fuel gauge ................................ 79Fuel selector .............................. 79Engine coolant temperaturegauge ....................................... 80

Service display .......................... 80Control indicators ...................... 81Turn signal ................................. 83Seat belt reminder ..................... 83Airbag and belt tensioners ......... 84Airbag deactivation .................... 84Charging system ....................... 84Malfunction indicator light .......... 85Service vehicle soon ................. 85Brake and clutch system ........... 85Operate pedal ............................ 85Antilock brake system (ABS) ..... 86Upshift ....................................... 86Power steering .......................... 86Ultrasonic parking assist ........... 86Electronic Stability Control off . . . 86Electronic Stability Control andTraction Control system ........... 86

Tyre pressure monitoringsystem ...................................... 87

Engine oil pressure .................... 87Low fuel ..................................... 87Immobiliser ................................ 88Exterior light .............................. 88High beam ................................. 88Rear fog light ............................. 88Cruise control ............................ 88Door open .................................. 88

Information displays ..................... 88Driver Information Centre .......... 88

Colour-Info-Display .................... 93Graphic-Info-Display .................. 94

Vehicle messages ........................ 95Warning chimes ......................... 97Battery voltage .......................... 97

Vehicle personalisation ................ 98OnStar ....................................... 101

70 Instruments and controls

ControlsSteering wheel adjustment

Unlock lever, adjust steering wheel,then engage lever and ensure it isfully locked.Do not adjust steering wheel unlessvehicle is stationary and steeringwheel lock has been released.

Steering wheel controls

The Infotainment system, the cruisecontrol and a connected mobilephone can be operated via thecontrols on the steering wheel.Further information is available in theInfotainment manual.Driver assistance systems 3 139.

Heated steering wheel

Activate heating by pressing *.Activation is indicated by the LED inthe button.


The highlighted grip areas of thesteering wheel are heated quickerand to a higher temperature than theother areas.Heating is operational when theengine is running and during anAutostop.Stop-start system 3 126.

Horn

Press j.

Windscreen wiper/washerWindscreen wiper

HI : fastLO : slowINT : interval wiping

orautomatic wiping with rainsensor

OFF : off

For a single wipe when thewindscreen wiper is off, press thelever down to position 1x.Do not use if the windscreen is frozen.Switch off in car washes.

Adjustable wiper interval

Wiper lever in position INT.Turn the adjuster wheel to adjust thedesired wipe interval:short interval : turn adjuster

wheel upwardslong interval : turn adjuster

wheel downwards


Automatic wiping with rain sensor

INT : automatic wiping with rainsensor

The rain sensor detects the amount ofwater on the windscreen andautomatically regulates the frequencyof the windscreen wiper.If the wiper frequency is above20 seconds the wiper arm movesslightly down to park position.

Adjustable sensitivity of the rainsensor

Turn the adjuster wheel to adjust thesensitivity:low sensitivity : turn adjuster

wheel downwardshigh sensitivity : turn adjuster

wheel upwards

Keep the sensor free from dust, dirtand ice.

Windscreen washer


Pull lever. Washer fluid is sprayedonto the windscreen and the wiperwipes a few times.Washer fluid 3 164

Rear window wiper/washer

Press the rocker switch to activate therear window wiper:upper position : continuous

operationlower position : intermittent

operationmiddle position : off

Push lever. Washer fluid is sprayedonto the rear window and the wiperwipes a few times.Do not use if the rear window isfrozen.Switch off in car washes.The rear window wiper comes onautomatically when the windscreenwiper is switched on and reverse gearis engaged.Activation or deactivation of thisfunction can be changed in the menuSettings in the Info-Display.Washer fluid 3 164Vehicle personalisation 3 98.

Outside temperatureA drop in temperature is indicatedimmediately and a rise in temperatureafter a time delay. Temperaturesbelow 3 °C are displayed flashing.

Illustration shows Graphic-Info-Display.


Illustration shows Colour-Info-Display.Uplevel-Display

If outside temperature drops to 3 °C,a warning message is displayed in theDriver Information Centre.

9 Warning

The road surface may already beicy even though the displayindicates a few degrees above 0°C.

ClockGraphic-Info DisplayPress CONFIG to open the Settingsmenu.Scroll through the list and select themenu item Time Date to display therespective submenu.

NoticeFor a detailed description of menuoperation, refer to the Infotainmentmanual.

Set time

Press the MENU-TUNE knob to enterthe Set time submenu.Turn the MENU-TUNE knob tochange the current value of the firstsetting.Press the MENU-TUNE knob toconfirm the set value.The cursor then switches to the nextvalue. If all values are set, you areautomatically returned to the nexthigher menu level.


Set date

Press the MENU-TUNE knob to enterthe Set date submenu.Turn the MENU-TUNE knob tochange the current value of the firstsetting.Press the MENU-TUNE knob toconfirm the set value.The cursor then switches to the nextvalue. If all values are set, you areautomatically returned to the nexthigher menu level.

Set time formatTo switch between the availableoptions, repeatedly press theMENU-TUNE knob.

Set date formatTo switch between the availableoptions, repeatedly press theMENU-TUNE knob.

RDS clock synchronizationThe RDS signal of most VHFtransmitters automatically sets thetime. RDS time synchronisation cantake a few minutes. Sometransmitters do not send a correcttime signal. In such cases, it isrecommended to switch off theautomatic time synchronisation.To switch between the options Onand Off, repeatedly press theMENU-TUNE knob.

Colour-Info DisplayPress ; then select the Settingsscreen button.Select Time & date settings to displaythe respective submenu.

NoticeFor a detailed description of menuoperation, refer to the Infotainmentmanual.

Set time formatTo select the desired time format, tapon the screen buttons 12 h or 24 h.

Set date formatTo select the desired date format, tapon the < and > screen buttons andchoose between the availableoptions.


Set time and date

To adjust the time and date settings,tap on the H and I screen buttons.

RDS clock synchronizationThe RDS signal of most VHFtransmitters automatically sets thetime. RDS time synchronisation cantake a few minutes. Sometransmitters do not send a correcttime signal. In such cases, it isrecommended to switch off theautomatic time synchronisation.To activate or deactivate RDS clocksynchronization, tap on the screenbuttons On or Off.

Power outlets

A 12 Volt power outlet is located in thecentre console.Do not exceed the maximum powerconsumption of 120 watts.With ignition off, the power outlet isdeactivated. Additionally, the poweroutlet is deactivated in the event oflow vehicle battery voltage.Electrical accessories that areconnected must comply with theelectromagnetic compatibilityrequirements laid down inDIN VDE 40 839.

Do not connect any current-deliveringaccessories, e.g. electrical chargingdevices or batteries.Do not damage the outlet by usingunsuitable plugs.Stop-start system 3 126.

Inductive charging

9 Warning

Inductive charging can affect theoperation of implantedpacemakers or other medicaldevices. If applicable, seekmedical advice before using theinductive charging device.

9 Warning

Remove any metal objects fromthe charging device beforecharging a mobile phone, as theseobjects could become very hot.


To charge a device, the ignition mustbe switsched on.LED status on the charging device:● Illuminates green: mobile phone

is charging.● Illuminates yellow: metall objects

have been detected in thecharging area. Remove objectsto allow charging.

PMA or Qi compatible mobile phonescould be charged inductivly.A back cover with an integrated coil(e.g. Samsung 4 and 5) or a jacket(e.g. some iPhone models) may berequired to charge a mobile phone.

The mobile phone must be smallerthan 8 cm in width and 15 cm in lengthto fit into the charging device.To charge a mobile phone:1. Remove all objects from the

charging device.2. Place the mobile phone with the

display facing upwards on thecharging device.

Cigarette lighter

The cigarette lighter is located in thecentre console.

Press in cigarette lighter. It switchesoff automatically once the element isglowing. Pull out lighter.

Ashtrays

Caution

To be used only for ash and not forcombustible rubbish.

The portable ashtray can be placed inthe cupholders.


Warning lights, gaugesand indicatorsInstrument clusterThe needles of the instruments brieflyrotate to the end position when theignition is switched on.

Speedometer

Indicates vehicle speed.

Odometer

The bottom line displays the recordeddistance in miles.

Trip odometerThe top line displays the recordeddistance since the last reset.To reset, press SET/CLR on the turnsignal lever for a few seconds3 88.Trip odometer counts up to a distanceof 2000 miles and then restarts at 0.

Tachometer

Displays the engine speed.Drive in a low engine speed range foreach gear as much as possible.

Caution

If the needle is in the red warningzone, the maximum permittedengine speed is exceeded. Engineat risk.


Fuel gauge

Displays the level in the fuel tank.The arrow indicates the vehicle sidewhere the fuel filler flap is located.During liquid gas operation, the levelin the gas tank is displayed.Control indicator Y illuminates if thelevel in the tank is low. Refuelimmediately if it flashes.During liquid gas operation, thesystem automatically switches over topetrol operation when gas tanks areempty 3 79.Never run the fuel tank dry.

Because of the fuel remaining in thetank, the top-up quantity may be lessthan the specified tank capacity.

Fuel selector

Press LPG to switch between petroland liquid gas operation. The LED inthe button shows the currentoperating mode.LED off : petrol operationLEDflashes

: checking conditions forfuel transition to liquidgas operation.Illuminates if conditionsare fulfilled.

LED illu‐minates

: liquid gas operation

LEDflashesfivetimesandextin‐guishes

: liquid gas tank is emptyor failure in liquid gassystem. A message isdisplayed in the DriverInformation Centre.

As soon as the liquid gas tank isempty, petrol operation isautomatically engaged until theignition is switched off.Fuel for liquid gas operation 3 153.


Engine coolant temperaturegauge

Displays the coolant temperature.left area : engine operating

temperature not yetreached

centralarea

: normal operatingtemperature

right area : temperature too high

Caution

If engine coolant temperature istoo high, stop vehicle, switch offengine. Danger to engine. Checkcoolant level.

Service displayThe engine oil life system lets youknow when to change the engine oiland filter. Based on drivingconditions, the interval at which anengine oil and filter change will beindicated can vary considerably.Midlevel-DisplayThe remaining engine oil life durationis displayed in percent beside thecontrol indicator I on the Midlevel-Display.

Uplevel-DisplayThe remaining oil life duration isdisplayed in percent in the VehicleInformation Menu on the Uplevel-Display.To display the remaining engine oillife duration use turn signal leverbuttons:


Press MENU to select the VehicleInformation Menu.Turn the adjuster wheel to selectRemaining Oil Life.

ResetPress SET/CLR on turn signal leverfor several seconds to reset. Theremaining engine oil life durationpage must be active. Switch onignition only, engine must beswitched off.The system must be reset every timethe engine oil is changed to ensureproper functionality. Seek theassistance of a workshop.

Next serviceWhen the system has calculated thatengine oil life has diminished, awarning message appears in theDriver Information Centre. Haveengine oil and filter changed by aworkshop within one week or300 miles (whichever occurs first).Driver Information Centre 3 88.Service information 3 209.

Control indicatorsThe control indicators described arenot present in all vehicles. Thedescription applies to all instrumentversions. Depending on theequipment, the position of the controlindicators may vary. When theignition is switched on, most controlindicators will illuminate briefly as afunctionality test.The control indicator colours mean:red : danger, important reminderyellow : warning, information, faultgreen : confirmation of activationblue : confirmation of activationwhite : confirmation of activation


Control indicators in the instrument cluster


Control indicators in the centreconsole

Overview

O Turn signal 3 83

X Seat belt reminder 3 83

v Airbag and belt tensioners3 84

V Airbag deactivation 3 84

p Charging system 3 84

Z Malfunction indicator light3 85

g Service vehicle soon 3 85

R Brake and clutch system3 85

- Operate pedal 3 85

u Antilock brake system (ABS)3 86

[ Upshift 3 86

c Power steering 3 86

r Ultrasonic parking assist3 86

n Electronic Stability Control off3 86

b Electronic Stability Control andTraction Control system 3 86

w Tyre pressure monitoringsystem 3 87

I Engine oil pressure 3 87

Y Low fuel 3 87

d Immobiliser 3 88

8 Exterior light 3 88

C High beam 3 88

r Rear fog light 3 88

m Cruise control 3 88

h Door open 3 88

Turn signalO illuminates or flashes green.

Illuminates brieflyThe parking lights are switched on.

FlashesA turn signal or the hazard warningflashers are activated.Rapid flashing: failure of a turn signallight or associated fuse.Bulb replacement 3 168, Fuses3 177.Turn signals 3 108.

Seat belt reminderSeat belt reminder on front seatsX for driver's seat illuminates orflashes red in the tachometer.


k for front passenger seat illuminatesor flashes red in the centre console,when the seat is occupied.

IlluminatesAfter the ignition has been switchedon until the seat belt has beenfastened.

FlashesAfter having started the engine for amaximum of 100 seconds until theseat belt has been fastened.Fastening the seat belt 3 38.

Seat belt status on rear seats

X in the Driver Information Centreflashes or illuminates.

IlluminatesAfter having started the engine for aminimum of 35 seconds until the seatbelt has been fastened.If an unfastened seat belt is fastenedwhilst driving.

FlashesAfter starting off when the seat belt isunfastened.Fastening the seat belt 3 38.

Airbag and belt tensionersv illuminates red.When the ignition is switched on, thecontrol indicator illuminates forapprox. four seconds. If it does notilluminate, does not go out after fourseconds or illuminates whilst driving,there is a fault in the airbag system.Seek the assistance of a workshop.The airbags and belt pretensionersmay fail to trigger in the event of anaccident.

Deployment of the belt pretensionersor airbags is indicated by continuousillumination of v.

9 Warning

Have the cause of the faultremedied immediately by aworkshop.

Belt pretensioners, airbag system3 37, 3 39.

Airbag deactivationV illuminates yellow.Illuminates for approx. 60 secondsafter the ignition is switched on. Thefront passenger airbag is activated.* illuminates yellow.The front passenger airbag isdeactivated.Airbag deactivation 3 44.

Charging systemp illuminates red.


Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunningStop, switch off engine. Vehiclebattery is not charging. Enginecooling may be interrupted. Thebrake servo unit may cease to beeffective. Seek the assistance of aworkshop.

Malfunction indicator lightZ illuminates or flashes yellow.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunningFault in the emission control system.The permitted emission limits may beexceeded. Seek the assistance of aworkshop immediately.

Flashes when the engine isrunningFault that could lead to catalyticconverter damage. Ease up on theaccelerator until the flashing stops.Seek the assistance of a workshopimmediately.

Service vehicle soong illuminates yellow.Additionally, a warning message isdisplayed in the Driver InformationCentre.The vehicle needs a service.Seek the assistance of a workshop.Vehicle messages 3 95.

Brake and clutch systemR illuminates red.The brake and clutch fluid level is toolow, when manual parking brake isnot applied 3 165.

9 Warning

Stop. Do not continue yourjourney. Consult a workshop.

Illuminates when the manual parkingbrake is applied and ignition isswitched on3 135.

Operate pedal- illuminates or flashes yellow.

IlluminatesClutch pedal must be depressed tostart the engine in Autostop mode.Stop-start system 3 126.

FlashesClutch pedal must be depressed for amain start of the engine 3 16, 3 125.On some versions, the operate pedalmessage is indicated in the DriverInformation Display 3 95.


Antilock brake system(ABS)u illuminates yellow.Illuminates for a few seconds after theignition is switched on. The system isready for operation when the controlindicator extinguishes.If the control indicator does not go outafter a few seconds, or if it illuminateswhile driving, there is a fault in theABS. The brake system remainsoperational but without ABSregulation.Antilock brake system 3 134.

Upshift[ illuminates green as controlindicator or is shown as a symbol inthe Driver Information Centre withUplevel-Display, when upshifting isrecommended for fuel savingreasons.Eco information menuThe gear shift indication is popped-upas a full page in the Driver InformationCentre.

EcoFlex drive assistant 3 88.

Power steeringc illuminates yellow.

Illuminates with power steeringdisabledFailure in the power steering system.Consult a workshop.

Illumination of c and bsimultaneouslyPower steering system must becalibrated, system calibration 3 138.

Ultrasonic parking assistr illuminates yellow.Fault in systemorFault due to sensors that are dirty orcovered by ice or snoworInterference due to external sourcesof ultrasound. Once the source ofinterference is removed, the systemwill operate normally.

Have the cause of the fault in thesystem remedied by a workshop.Ultrasonic parking assist 3 142.

Electronic Stability Controlofft illuminates yellow.The system is deactivated.

Electronic Stability Controland Traction Control systemb flashes or illuminates yellow.

FlashesThe system is actively engaged.Engine output may be reduced andthe vehicle may be brakedautomatically to a small degree.

IlluminatesA fault in the system is present. Awarning message appears in theDriver Information Centre. Continueddriving is possible. The system is not


operational. Driving stability,however, may deteriorate dependingon road surface conditions.Have the cause of the fault remediedby a workshop.Electronic Stability Control 3 137,Traction Control system 3 136.

Tyre pressure monitoringsystemw illuminates or flashes yellow.

IlluminatesTyre pressure loss. Stop immediatelyand check tyre pressure.

FlashesFault in system or tyre withoutpressure sensor mounted (e.g. sparewheel). After 60-90 seconds thecontrol indicator illuminatescontinuously. Consult a workshop.Tyre pressure monitoring system3 185.

Engine oil pressureI illuminates red.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunning

Caution

Engine lubrication may beinterrupted. This may result indamage to the engine and/orlocking of the drive wheels.

1. Depress the clutch.2. Select neutral gear.3. Move out of the flow of traffic as

quickly as possible withoutimpeding other vehicles.

4. Switch off ignition.

9 Warning

When the engine is off,considerably more force is neededto brake and steer.During an Autostop the brakeservo unit will still be operational.Do not remove key until vehicle isstationary, otherwise the steeringwheel lock could engageunexpectedly.

Check oil level before seeking theassistance of a workshop 3 163.

Low fuelY illuminates or flashes yellow.

IlluminatesLevel in fuel tank is too low.

FlashesFuel used up. Refuel immediately.Never run the tank dry.Refuelling 3 155.Catalytic converter 3 129.


Immobiliserd flashes yellow.Fault in the immobiliser system. Theengine cannot be started.

Exterior light8 illuminates green.The exterior lights are on 3 105.

High beamC illuminates blue.Illuminated when high beam is on orduring headlight flash 3 106.

Rear fog lightr illuminates yellow.The rear fog light is on 3 108.

Cruise controlm illuminates white or green.

Illuminates whiteThe system is on.

Illuminates greenCruise control is active.Cruise control 3 139.

Door openh illuminates red.A door or the tailgate is open.

Information displaysDriver Information CentreThe Driver Information Centre islocated in the instrument cluster.It is available as Midlevel-Display orUplevel-Display.

Midlevel-Display

Indication of:● overall odometer● trip odometer● control indicators● vehicle information menu, see

following


● trip/fuel information menu, seefollowing

● vehicle messages, displayed ascode numbers 3 95.

Select menu pages by pressingMENU or turning the adjuster wheelon the turn signal lever.Some of the displayed functions differwhen the vehicle is being driven or ata standstill. Some functions are onlyavailable when the vehicle is beingdriven.Vehicle information menu and trip/fuel information menu are selectablepages, while vehicle messages andcontrol indicators pop-up whenrequired.

Uplevel-Display

Indication of:● Vehicle Information Menu X● Trip/Fuel Information MenuW● EcoFlex Drive Assist Menu s

Select menu pages by pressingMENU on the turn signal lever; mainmenu symbols are indicated in the topline of the display.Some of the displayed functions differwhen the vehicle is being driven or ata standstill. Some functions are onlyavailable when the vehicle is beingdriven.

Vehicle messages pop-up whenrequired.Vehicle personalisation 3 98.Memorised settings 3 21.

Selecting menus and functionsThe menus and functions can beselected via the buttons on the turnsignal lever.

Press MENU to switch between themenus or to return from a submenu tothe next higher menu level.Turn the adjuster wheel to highlight amenu option or to set a numeric value.


Press SET/CLR to select a function orto confirm a message.

Vehicle Information MenuPress MENU to select the VehicleInformation page.Turn the adjuster wheel to select asubmenu.Follow the instructions given in thesubmenus.● Unit

Press SET/CLR while page isdisplayed. Select imperial(unit 1) or metric (unit 3) byturning the adjuster wheel. PressSET/CLR to set the unit.

● Tyre PressureTyre pressure of all wheels isdisplayed on this page duringdriving 3 185.

● Tyre LoadThe tyre pressure categoryaccording to the actually inflatedtyre pressure can be selected3 185.

● Remaining Oil LifeIndicates an estimate of the oil'suseful life. The number in %means the current remaining oillife and indicates when to changethe engine oil and filter 3 80.

● Speed WarningThe speed warning displayalarms when a set speed isexceeded.To set the speed warning, pressSET/CLR while the page isdisplayed. Turn the adjusterwheel to select the value. PressSET/CLR to set the speed.If the selected speed limit isexceeded, a warning chimesounds. Once the speed is set,this feature can be turned off bypressing SET/CLR while viewingthis page.


Selection and indication can bedifferent between Midlevel- andUplevel-Display.

Trip/Fuel Information MenuPress MENU to select the Trip/FuelInformation Page.Turn the adjuster wheel to select asubmenu.Midlevel-Display

Midlevel-Display may be availablewith trip/fuel information menu.Uplevel-Display

● trip odometer 1● average consumption 1● average speed 1

● trip odometer 2

● average consumption 2● average speed 2

● digital speed● range● instantaneous consumption

Selection and indication can bedifferent between Midlevel- andUplevel-Display.

Two Trip computerThe information of two trip computercan be reset separately for odometer,average consumption and averagespeed, making it possible to displaydifferent trip information.


Trip odometerTrip odometer displays the currentdistance since a certain reset.Trip odometer counts up to a distanceof 2000 miles and then restarts at 0.Reset trip odometer by pressingSET/CLR for a few seconds on therespective page.

Average consumptionDisplay of average consumption. Themeasurement can be reset at anytime and starts with a default value.To reset, press SET/CLR for a fewseconds on the respective page.

On vehicles with LPG engines:Average consumption is indicated forthe currently selected mode (LPG orpetrol).

Average speedDisplay of average speed. Themeasurement can be reset at anytime.To reset, press SET/CLR for a fewseconds on the respective page.

Digital speedDigital display of the instantaneousspeed.

Fuel rangeRange is calculated from current fueltank level and current consumption.The display shows average values.After refuelling, the range is updatedautomatically after a brief delay.When the fuel level in the tank is low,a message appears on the display.Y in the fuel gauge illuminates.When the tank must be refuelledimmediately, a warning messagepops-up on the display. Y in the fuelgauge flashes.

Y 3 87.

Fuel range LPG versionDisplay of approximate fuel rangeavailable with the remaining fuel ineach respective fuel tank of petrol andLPG fuel, along with a total range ofboth fuel types together. Switchbetween the mode by pressingSET/CLR.

Instantaneous consumptionDisplay of the instantaneousconsumption.On vehicles with LPG engines:Instantaneous consumption isindicated for the currently selectedmode; LPG or petrol.

ECO Information Menu sPress MENU to select s in the topline of the Display.Turn the adjuster wheel to select asubmenu. Press SET/CLR to confirm.


Submenus are:

● Shift indication: Current gear isindicated inside an arrow. Thefigure above recommendsupshifting for fuel savingreasons.Eco index display: The currentfuel consumption is indicated ona segment display. Foreconomical driving, adapt yourdriving style to keep the filledsegments within the Eco area.The more segments are filled, thehigher the fuel consumption.Simultaneously the averageconsumption value is indicated.

● Top consumers: List of topcomfort consumers currentlyswitched on is displayed indescending order. Fuel savingpotential is indicated.

● Economy Trend: Displays theaverage consumptiondevelopment over a distance of31 miles. Filled segments displaythe consumption in 3.1 mile stepsand shows the effect oftopography or driving behaviouron fuel consumption.

Colour-Info-DisplayDepending on the vehicleconfiguration, the vehicle has aColour-Info-Display with touchscreenfunctionality.The Colour-Info-Display withtouchscreen functionality indicates incolour:● time 3 74● outside temperature 3 73● date 3 74● electronic climate control settings

3 116● parking assist and advanced

parking assist instructions3 142

● Infotainment system, seedescription in the Infotainmentmanual

● system messages● vehicle messages 3 95● settings for vehicle

personalisation 3 98The type of information and how it isdisplayed depends on the settingsmade.


Selecting menus and settingsMenus and settings are selected viathe touch screen display.

Press X to switch on the display.Press ; to display the homepage.Tap required menu display icon withthe finger.Tap a respective icon to confirm aselection.Tap 9 to return to the next highermenu level.Press ; to return to the homepage.For further information, seeInfotainment manual.

Vehicle personalisation 3 98.

Graphic-Info-DisplayDepending on the vehicleconfiguration, the vehicle has aGraphic-Info-Display.

The Graphic-Info-Display indicates:● time 3 74● outside temperature 3 73● date 3 74● electronic climate control settings

3 116

● Infotainment system, seedescription in the Infotainmentmanual

● settings for vehiclepersonalisation 3 98

Selecting menus and settingsMenus and settings are accessed viathe display.

Press CONFIG: Menu page Settingsis displayed.Turn knob MENU-TUNE to select asetting or value.Press knob MENU-TUNE to confirma setting or value.Press BACK to exit a menu or settingwithout changing or delete the lastcharacter in a character sequence.Press the BACK for a few seconds todelete the entire entry.


To exit the Settings menu, pressBACK repeatedly or press CONFIGafter confirming the changes.Vehicle personalisation 3 98.Memorised settings 3 21.

Vehicle messagesMessages are indicated mainly in theDriver Information Centre, in somecases together with a warning andsignal buzzer.

Press SET/CLR, MENU or turn theadjuster wheel to confirm a message.

Vehicle messages on theMidlevel-Display

The vehicle messages are displayedas code numbers.

No. Vehicle message

1 Change engine oil

3 Engine coolant level low

4 Air conditioning off

5 Steering wheel is locked

7 Turn steering wheel, switchignition off then on


No. Vehicle message

9 Turn steering wheel, startengine again

12 Vehicle overloaded

13 Compressor overheated

15 Centre high-mounted brakelight failure

16 Brake light failure

17 Headlight levelling malfunction

18 Left low beam failure

19 Rear fog light failure

20 Right low beam failure

21 Left sidelight failure

22 Right sidelight failure

23 Reversing light failure

24 Number plate light failure

25 Left front turn signal failure

26 Left rear turn signal failure

27 Right front turn signal failure

No. Vehicle message

28 Right rear turn signal failure

35 Replace battery in radio remotecontrol

48 Clean side blind spot alertsystem

53 Tighten fuel filler cap

56 Tyre pressure imbalance onfront axle

57 Tyre pressure imbalance onrear axle

58 Winter tyres detection

59 Open then close driver window

60 Open then close frontpassenger window

66 Service theft alarm system

67 Service steering wheel lock

68 Service power steering

75 Service air conditioning

No. Vehicle message

76 Service side blind spot alertsystem

79 Top up engine oil

82 Change engine oil soon

84 Engine power reduced

89 Service vehicle soon

95 Service airbag

128 Bonnet open

134 Parking assist fault, cleanbumper

136 Service parking assist

174 Low vehicle battery

151 Press clutch to start

258 Parking assist off


Vehicle messages on theUplevel-Display

The vehicle messages are displayedas text. Follow the instructions givenin the messages.The system displays messagesregarding the following topics:● fluid levels● anti-theft alarm system● brakes● ride control systems● cruise control, speed limiter● parking assist systems● lighting, bulb replacement

● wiper/washer system● doors, windows● radio remote control● seat belts● airbag systems● engine and transmission● tyre pressure● vehicle battery

Vehicle messages on theColour-Info-DisplaySome important messages appearadditionally in theColour-Info-Display. Somemessages only pop-up for a fewseconds.

Warning chimesWhen starting the engine or whilstdrivingOnly one warning chime will sound ata time.The warning chime regardingunfastened seat belts has priorityover any other warning chime.

● If seat belt is not fastened.● If a door or the tailgate is not fully

closed when starting off.● If a certain speed is exceeded

with parking brake applied.● If a programmed speed is

exceeded.● If a warning message appears in

the Driver Information Centre orInfo-Display.

● If the parking assist detects anobject.

● If the reverse gear is engagedand the rear end carrierextended.

When the vehicle is parked and/orthe driver's door is opened● With exterior lights on.

During an Autostop● If the driver's door is opened.

Battery voltageMidlevel-Display


When the vehicle battery voltage isrunning low, a warning code 174 willappear in the Driver InformationCentre.Uplevel-DisplayWhen the vehicle battery voltage isrunning low, a warning message willappear in the Driver InformationCentre.1. Switch off immediately any

electrical consumers which arenot required for a safe drive, e.g.seat heating, heated rear windowor other main consumers.

2. Charge the vehicle battery bydriving continuously for a while orby using a charging device.

The warning message or warningcode will disappear after the enginehas been started twice consecutivelywithout a voltage drop.If the vehicle battery cannot berecharged, have the cause of the faultremedied by a workshop.

Vehicle personalisationThe vehicle's behaviour can bepersonalised via changing thesettings in the Info-Display.Some of the personal settings fordifferent drivers can be memorisedindividually for each vehicle key.Memorised settings 3 21.Depending on vehicle equipment andcountry-specific regulations some ofthe functions described below mightnot be available.Some functions are only displayed oractive when the engine is running.

Personal settingsGraphic-Info-DisplayPress CONFIG for the Settings menu.Turn the MENU-TUNE knob to moveto the desired setup menu, then pressMENU-TUNE.

Select Settingsand then Vehiclesettings.

Vehicle settings● Climate and air quality

Auto fan speed: Modifies thelevel of the cabin airflow of theclimate control in automaticmode.


Air conditioning mode: Controlsthe state of the coolingcompressor when the vehicle isstarted. Last setting(recommended) or at vehiclestart is either always ON oralways OFF.Auto rear demist: Activatesautomatically rear heatedwindow.

● Comfort settingsChime volume: Changes thevolume of warning chimes.Personalization by driver:Activates or deactivates thepersonalisation function.Rear auto wipe in reverse:Activates or deactivatesautomatic switching on of therear window wiper when reversegear is engaged.

● Park assist / Collision detectionPark assist: Activates ordeactivates the ultrasonicsensors.

Side blind zone alert: Changesthe settings for the side blind spotalert system.

● Exterior ambient lightingExterior lighting by unlocking:Activates or deactivates the entrylighting.Duration upon exit of vehicle:Activates or deactivates andchanges the duration of exitlighting.

● Power door locksAuto door lock: Activates ordeactivates the automatic doorlocking function after switchingon ignition.Stop door lock if door open:Activates or deactivates the doorlocking function while a door isopen.Delayed door lock: Activates ordeactivates the delayed doorlocking function. This menuoption is displayed with Stop doorlock if door open deactivated.Central locking system 3 22.

● Remote locking, unlocking,startingRemote unlock feedback:Activates or deactivates thehazard warning flasher feedbackwhilst unlocking.Passive door unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.Auto relock doors: Activates ordeactivates the automatic relockfunction after unlocking withoutopening the vehicle.

● Restore factory settings:Resets all settings to the defaultsettings.

Personal settingsColour-Info-DisplayWhen audio is switched on, press ;on the control panel.


Select Settingsand then Vehiclesettings.

Vehicle settings● Climate & air quality

Auto Fan Max Speed: Modifiesthe level of the cabin airflow of theclimate control in automaticmode.Air Conditioning Mode: Controlsthe state of the coolingcompressor when the vehicle isstarted. Last setting(recommended) or at vehiclestart is either always on or alwaysoff.Auto Rear Defog: Automaticallyactivates heated rear window.

● Collision / Detection SystemsPark Assist: Activates ordeactivates the ultrasonicparking assist.Side Blind Zone Alert: Activatesor deactivates side blind zonealert.

● Comfort and ConvenienceChime Volume: Changes thevolume of warning chimes.

Personalization By Driver:Activates or deactivates thepersonalisation function.Auto Wipe in Reverse Gear:Activates or deactivatesautomatic switching on of therear window wiper when reversegear is engaged.

● LightingVehicle Locator Lights: Activatesor deactivates the entry lighting.Exit Lighting: Activates ordeactivates and changes theduration of exit lighting.

● Power Door LocksUnlocked Door Anti Lock Out:Activates or deactivates the doorlocking function while a door isopen.Auto Door Lock: Activates ordeactivates the automatic doorlocking function after switchingon ignition.Auto Door Unlock: Changes theconfiguration to unlock only thedriver's door or the whole vehicleafter switching off ignition.


Delayed Door Lock: Activates ordeactivates the delayed doorlocking function. This featuredelays the actual locking of thedoors until all doors are closed.

● Remote Lock, Unlock, StartRemote Unlock Light Feedback:Activates or deactivates thehazard warning flasher feedbackwhilst unlocking.Remote Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.Relock Remotely UnlockedDoors: Activates or deactivatesthe automatic relock functionafter unlocking without openingthe vehicle.

OnStarOnStar is a personal connectivity andservice assistant with integratedWi-Fi hotspot. The OnStar service isavailable 24 hours a day, seven daysa week.NoticeOnStar is not available for allmarkets. For further information,contact your workshop.NoticeIn order to be available andoperational, OnStar needs a validOnStar subscription, functioningvehicle electrics, mobile service andGPS satellite link.

To activate the OnStar services andset up an account, press Z and speakwith an advisor.Depending on the equipment of thevehicle, the following services areavailable:● Emergency services and support

in the case of a vehiclebreakdown

● Wi-Fi hotspot

● Smartphone application● Remote control, e.g. location of

the vehicle, activation of horn andlights, control of central lockingsystem

● Stolen vehicle assistance● Vehicle diagnostics● Destination downloadNoticeThe OnStar module of the vehicle isdeactivated after ten days without anignition cycle. Functions requiring adata connection will be availableagain after switching on the ignition.

OnStar buttons


NoticeDepending on the equipment, theOnStar buttons can also beintegrated in the rear view mirror.

Privacy buttonPress and hold j until a message isheard to activate or deactivate thetransmission of the vehicle location.Press j to answer a call or to end acall to an advisor.Press j to access the Wi-Fi settings.

Service buttonPress Z to establish a connection toan advisor.

SOS buttonPress [ to establish a priorityemergency connection to a speciallytrained emergency advisor.

Status LEDGreen: The system is ready.Green flashing: The system is on acall.Red: A problem arose.Off: System is in standby mode.

Red / green flashing for a short periodof time: Transmission of the vehiclelocation has been deactivated.

OnStar services

General servicesIf you need any informationconcerning e.g. opening hours, pointsof interest and destinations or if youneed any support e.g. in the case of avehicle breakdown, a flat tyre andempty fuel tank, press Z to establisha connection to an advisor.

Emergency servicesIn the case of an emergency situation,press [ and talk to an advisor. Theadvisor then contacts emergency orassistance service providers anddirects them to your vehicle.In the case of an accident withactivation of airbags or belttensioners, an automatic emergencycall is established. The advisor isimmediately connected to yourvehicle to see whether help isneeded.

Wi-Fi hotspotThe Wi-Fi hotspot of the vehicleprovides internet connectivity with amaximum speed of 4G/LTE.NoticeThe Wi-Fi hotspot functionality is notavailable for all markets.

Up to seven devices may beconnected.To connect a mobile device with theWi-Fi hotspot:1. Press j and then select Wi-Fi

settings on the Info-Display. Thesettings displayed include the Wi-Fi hotspot name (SSID),password and connection type.

2. Start a Wi-Fi network search onyour mobile device.

3. Select your vehicle hotspot(SSID) when listed.

4. When prompted, enter thepassword on your mobile device.


NoticeTo change the SSID or password,press Z and talk to an advisor or login to your account.

To switch off the Wi-Fi hotspotfunctionality, press Z to call anadvisor.

Smartphone appWith the My Vauxhall smartphoneapp, some vehicle functions can beoperated remotely.The following functions are available:● Lock or unlock vehicle.● Honk horn or flash lights.● Check fuel level, engine oil life

and tyre pressure (only with tyrepressure monitoring system).

● Send navigation destination tothe vehicle, if equipped with abuilt-in navigation system.

● Locate vehicle on a map.● Manage Wi-Fi settings.

To operate these functions, downloadthe app from Apple's App Store orGoogle Play Store.

Remote controlIf desired, use any phone to call anadvisor, who can remotely operatespecific vehicle functions. Find therespective OnStar phone number onour country-specific website.The following functions are available:● Lock or unlock vehicle.● Provide information on the

vehicle location.● Honk horn or flash lights.

Stolen vehicle assistanceIf the vehicle is stolen, report the theftto the authorities and request OnStarstolen vehicle assistance. Use anyphone to call an advisor. Find therespective OnStar phone number onour country-specific website.OnStar can provide support inlocating and recovering the vehicle.Theft alertWhen the anti-theft alarm system istriggered, a notification is sent toOnStar. You are then informed aboutthis event by text message or email.

Restart preventionBy sending remote signals, OnStarcan prevent the vehicle fromrestarting once it has been turned off.

On-demand diagnosticsAt any time e.g. if the vehicle displaysa vehicle message, press Z tocontact an advisor and ask tocomplete a real-time diagnostic checkto directly determine the issue.Depending on the results, the advisorwill provide further support.

Diagnostic reportThe vehicle automatically transmitsdiagnostic data to OnStar whichsends a monthly email report to youand your preferred workshop.NoticeThe workshop notification functioncan be disabled in your account.

The report contains the status of keyoperating systems of the vehicle likeengine, transmission, airbags, ABS,and other major systems. It alsoprovides information on possible


maintenance items and tyre pressure(only with tyre pressure monitoringsystem).To look at the information in greaterdetail, select the link within the emailand log in to your account.

Destination downloadA desired destination can be directlydownloaded to the navigation system.Press Z to call an advisor anddescribe the destination or point ofinterest.The advisor can look up any addressor point of interest and directly sendthe destination to the built-innavigation system.

OnStar settings

OnStar PINTo have full access to all OnStarservices, a four-digit PIN is required.The PIN has to be personalised whenfirst talking to an advisor.To change the PIN, press Z to call anadvisor.

Account dataAn OnStar subscriber has an accountwhere all the data is stored. Torequest a change of the accountinformation, press Z and talk to anadvisor or log in to your account.If the OnStar service is used onanother vehicle, press Z and requestthat the account be transferred to thenew vehicle.NoticeIn any case, if the vehicle is disposedof, sold or otherwise transferred,immediately inform OnStar aboutthe changes and terminate theOnStar service on this vehicle.

Vehicle locationThe vehicle location is transmitted toOnStar when service is requested ortriggered. A message on the Info-Display informs about thistransmission.To activate or deactivate thetransmission of the vehicle location,press and hold j until an audiomessage is heard.

The deactivation is indicated by thestatus light flashing red and green fora short period of time and each timethe vehicle is started.NoticeIf the transmission of the vehiclelocation is deactivated, someservices are no longer available.NoticeThe vehicle location always remainsaccessible to OnStar in the case ofan emergency.

Find the privacy policy in youraccount.

Software updatesOnStar may remotely carry outsoftware updates without furthernotice or consent. These updates areto enhance or maintain safety andsecurity or the operation of thevehicle.These updates may concern privacyissues. Find the privacy policy in youraccount.

Lighting 105

Lighting

Exterior lighting .......................... 105Light switch .............................. 105Automatic light control ............. 106High beam ............................... 106Headlight flash ......................... 106Headlight range adjustment .... 107Headlights when drivingabroad .................................... 107

Daytime running lights ............. 107Hazard warning flashers .......... 107Turn and lane-change signals . 108Rear fog lights ......................... 108Parking lights ........................... 108Reversing lights ....................... 109Misted light covers ................... 109

Interior lighting ........................... 109Instrument panel illuminationcontrol ..................................... 109

Interior lights ............................ 109Lighting features ........................ 111

Entry lighting ............................ 111Exit lighting .............................. 111Battery discharge protection .... 112

Exterior lightingLight switch

Turn light switch:7 : lights off8 : sidelights9 : headlights

Control indicator 8 3 88.

Light switch with automatic lightcontrol

Turn light switch:AUTO : automatic light control: low

beam is switched on and offautomatically depending onexternal lighting conditions

m : activation or deactivation ofthe automatic light control.Switch turns back to AUTO

8 : sidelights9 : headlights

The current status of the automaticlight control is displayed In the DriverInformation Centre.

106 Lighting

When switching on the ignition,automatic light control is active.When headlights are on, 8illuminates. Control indicator 83 88.

Tail lightsTail lights are illuminated togetherwith headlights and sidelights.

Automatic light control

When the automatic light controlfunction is switched on and theengine is running, the systemswitches between daytime runninglight and headlights automatically

depending on the lighting conditionsand information given by the rainsensor system.Daytime running light 3 107.

Automatic headlight activationWhen the automatic light controlfunction is switched on and theengine is running, the headlights areswitched on during poor lightingconditions.Furthermore the headlights areswitched on if the windscreen wipershave been activated for severalwipes.

Tunnel detectionWhen a tunnel is entered theheadlights are switched on withoutany delay.

High beam

To switch from low to high beam,push lever.To switch to low beam, push leveragain or pull.

Headlight flashTo activate the headlight flash, pulllever.

Lighting 107

Headlight range adjustmentManual headlight rangeadjustment

To adapt headlight range to thevehicle load to prevent dazzling: turnthumb wheel ? to required position.0 : front seats occupied1 : all seats occupied2 : all seats occupied and load

compartment laden3 : driver's seat occupied and load

compartment laden

Headlights when drivingabroadThe asymmetrical headlight beamextends visibility at the edge of theroad at the passenger side.However, when driving in countrieswhere traffic drives on the oppositeside of the road, adjust the headlightsto prevent dazzling of oncomingtraffic.

Turn adjuster on both headlighthousings 1/4 turn clockwise to settourist mode.

Daytime running lightsDaytime running light increasesvisibility of the vehicle during daylight.They are switched on automaticallywhen ignition is on.

Hazard warning flashers

Operated by pressing ¨.In the event of an accident with airbagdeployment the hazard warningflashers are activated automatically.

108 Lighting

Turn and lane-changesignals

lever up : right turn signallever down : left turn signal

If the lever is moved past theresistance point, the turn signal isswitched on constantly. When thesteering wheel moves back, the turnsignal is automatically deactivated.For three flashes, e.g. when changinglanes, press the lever until resistanceis felt and then release.Move the lever to the resistance pointand hold for longer indication.

Switch the turn signal off manually bymoving the lever to its originalposition.

Rear fog lights

Operated by pressing r.Light switch in position AUTO:switching on rear fog light will switchon headlights automatically.

Parking lights

When the vehicle is parked, theparking lights on one side can beactivated:1. Switch off ignition.2. Move turn signal lever all the way

up (right parking lights) or down(left parking lights).

Confirmed by a signal and thecorresponding turn signal controlindicator.

Lighting 109

Reversing lightsThe reversing light comes on whenthe ignition is on and reverse gear isselected.

Misted light coversThe inside of the light housing maymist up briefly in poor, wet and coldweather conditions, in heavy rain orafter washing. The mist disappearsquickly by itself; to help switch on theheadlights.

Interior lightingInstrument panelillumination control

Brightness of the following lights canbe adjusted when the exterior lightsare on:● instrument panel illumination● ambient light● dome light● Info-Display● illuminated switches and

operation elements

Turn thumb wheel A and hold untilthe desired brightness is obtained.

Interior lightsFront courtesy lightDuring entry and exit of the vehicle,the courtesy light automaticallyswitches on then off after a delay.

Operate rocker switch:w : automatic switching on

and offpress u : onpress v : off

110 Lighting

NoticeIn the event of an accident withairbag deployment the courtesylights are turned on automatically.

Dome lightSpotlight incorporated in the interiorlighting comes on when headlightsare switched on.Dome light illuminates gear shiftingconsole indirectly.

Ambient lightAmbient light consists of indirectlights in the doors, in the instrumentpanel below the heating andventilation unit and in the passengerfoot well. 8 colours can be selected bya button in the roof console.

Operate button with ignition switchedon:m one briefpress

: on or off

S repeatedbrief presses

: colours change insteps

S long press : colours changecontinuously

Ambient light can be dimmed with thethumb wheel A together with theinstrument panel illumination 3 109.The selected colour remains the nexttime the ignition is switched on.Ambient light comes on automaticallywhen switching off ignition andextinguishes after opening a door.

Pressing m after switching off ignition;ambient light remains on for60 minutes.

Starlight panelStarlight panel consists of approx.64 LEDs. The intensity can bedimmed with a button in the roofconsole.

Lighting 111

Operate button with ignition switchedon:m one briefpress

: on or off

T repeatedbrief presses

: dimmingstepwise

T long press : dimmingcontinuously

The selected intensity remains thenext time the ignition is switched on.Starlight comes on automaticallywhen switching off ignition andextinguishes after opening a door.Pressing m after switching off ignition;starlight remains on for 60 minutes.

Lighting featuresEntry lightingWelcome lightingThe following lights are switched onfor a short time by unlocking thevehicle with the radio remote control:● headlights● tail lights● number plate lights● instrument panel light● interior lights

Some functions are only operablewhen it is dark outside to facilitatelocating the vehicle.The lighting switches off immediatelywhen the ignition key is turned toposition 1 3 124.Activation or deactivation of thisfunction can be changed in theInfo-Display.Vehicle personalisation 3 98.The settings can be saved for the keybeing used 3 21.

The following lights will additionallyswitch on when the driver's door isopened:● illumination of some switches● Driver Information Centre● ambient light● starlight panel

Exit lightingThe following lights switch on if thekey is removed from the ignitionswitch:● interior lights● instrument panel light (only when

it is dark)● ambient light● starlight panel

They will switch off automatically aftera delay and will be activated again ifthe driver's door is opened.

Path lightingHeadlights, tail lights and numberplate lights illuminate the surroundingarea for an adjustable time afterleaving the vehicle.

112 Lighting

Activating

1. Switch off the ignition.2. Remove the ignition key.3. Open the driver's door.4. Pull the turn signal lever.5. Close the driver's door.

If the driver's door is not closed thelights switch off after two minutes.Exit lighting is switched offimmediately if the turn signal lever ispulled while the driver's door is open.Activation, deactivation and durationof this function can be changed in theInfo-Display. Vehicle personalisation3 98.

The settings can be saved for the keybeing used 3 21.

Battery discharge protectionVehicle battery state of chargefunctionThe function guarantees longestvehicle battery life via a generatorwith controllable power output andoptimised power distribution.To prevent discharge of the vehiclebattery when driving, followingsystems are reduced automatically intwo stages and finally switched off:● auxiliary heater● heated rear window● heated mirrors● heated seats● fan

In the second stage a message whichconfirms the activation of the vehiclebattery discharge protection will bedisplayed in the Driver InformationCentre.

Switching off electric lightsTo prevent discharge of the vehiclebattery when the ignition is switchedoff, some interior lights are switchedoff automatically after some time.

Climate control 113

Climate control

Climate control systems ............. 113Heating and ventilation system 113Air conditioning system ........... 114Electronic climate controlsystem .................................... 116

Air vents ..................................... 121Adjustable air vents ................. 121Fixed air vents ......................... 121

Maintenance .............................. 121Air intake ................................. 121Pollen filter ............................... 121Air conditioning regularoperation ................................ 122

Service .................................... 122

Climate control systemsHeating and ventilationsystem

Controls for:● temperature● fan speed● air distribution

Heated rear window Ü 3 30.Heated seats ß 3 36.Heated steering wheel * 3 70.

Temperaturered : warmblue : cold

Heating will not be fully effective untilthe engine has reached normaloperating temperature.

Fan speedAdjust the air flow by switching the fanto the desired speed.

Air distributionM : to head areaL : to head area and foot wellK : to foot well and windscreenJ : to windscreen, front door

windows and foot welll : to windscreen and front door

windows

Intermediate settings are possible.

114 Climate control

Demisting and defrosting thewindows

● Set temperature control towarmest level.

● Set fan speed to highest speed.● Set air distribution control to l.● Switch on heated rear window Ü.● Open side air vents as required

and direct them towards doorwindows.

● For simultaneous warming of thefoot well, set air distributioncontrol to J.

Air conditioning system

Controls for:● temperature● fan speed● air distributionn : cooling4 : air recirculationÜ : heated rear window 3 30

Heated seats ß 3 36.Heated steering wheel * 3 70.

Temperaturered : warmblue : cold

Heating will not be fully effective untilthe engine has reached normaloperating temperature.

Fan speedAdjust the air flow by switching the fanto the desired speed.

Air distributionM : to head areaL : to head area and foot wellK : to foot well and windscreenJ : to windscreen, front door

windows and foot welll : to windscreen and front door

windows (air conditioning isactivated in the background tohelp preventing windows fromfogging)

Intermediate settings are possible.

Climate control 115

Cooling n

Press n to switch on cooling. TheLED in the button illuminates toindicate activation. Cooling is onlyfunctional when the engine is runningand climate control fan is switched on.Press n again to switch off cooling.The air conditioning system cools anddehumidifies (dries) as soon as theoutside temperature is slightly abovethe freezing point. Thereforecondensation may form and drip fromunder the vehicle.If no cooling or drying is required,switch off the cooling system for fuelsaving reasons.

Activated cooling may inhibitAutostops.Stop-start system 3 126.

Air recirculation system 4

Press 4 to activate air recirculationmode. The LED in the buttonilluminates to indicate activation.Press 4 again to deactivaterecirculation mode.

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the air

humidity increases, so thewindows may mist up from inside.The quality of the passengercompartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen may mistup from outside, when cold air isdirected to it. If windscreen mists upfrom outside, activate windscreenwiper and deactivate l.

Maximum coolingBriefly open the windows so that hotair can disperse quickly.

116 Climate control

● Switch on cooling n.● Air recirculation system 4 on.● Set temperature control to

coldest level.● Set fan speed to highest level.● Set air distribution control to M.● Open all vents.

Demisting and defrosting thewindows l

● Set temperature control towarmest level.

● Set fan speed to highest level.● Set air distribution control to l.● Switch on heated rear window Ü.● Open side air vents as required

and direct them towards the doorwindows.

NoticeIf air distribution mode l is selectedwhile engine is running, an Autostopwill be inhibited until another airdistribution is selected.If air distribution mode l is selectedwhile the engine is in an Autostop,the engine will restart automatically.

Stop-start system 3 126.

Electronic climate controlsystem

Climate control 117

Controls for:● fan speed● temperature● air distributionn : coolingAUTO : automatic mode4 : manual air recirculationV : demisting and defrostingÜ : heated rear window 3 30

Heated seats ß 3 36.Heated steering wheel * 3 70.In Automatic mode temperature, fanspeed and air distribution areregulated automatically.

Climate control settings are shown onthe Info-Display. Settingmodifications are briefly popped-up,superimposed over the currentlydisplayed menu.The electronic climate control systemis only fully operational when theengine is running.

Automatic mode AUTO

Basic setting for maximum comfort:● Press AUTO, the air distribution

and fan speed are regulatedautomatically. The LED in thebutton illuminates to indicateactivation.

● Open all air vents to allowoptimised air distribution inautomatic mode.

● Press n to switch on optimalcooling and demisting. The LEDin the button illuminates toindicate activation.

● Set the preselected temperatureusing the centre rotary knob.Recommended temperature is22 °C.

Temperature preselectionSet temperature by turning the centrerotary knob to the desired value. It isindicated in the display of the switch.For reasons of comfort, changetemperature only in small increments.

118 Climate control

If the minimum temperature Lo is set,the climate control system runs atmaximum cooling, if cooling n isswitched on.If the maximum temperature Hi is set,the climate control system runs atmaximum heating.NoticeIf n is switched on, reducing the setcabin temperature can cause theengine to restart from an Autostop orinhibit an Autostop.


Demisting and defrosting thewindows V

● Press V. The LED in the buttonilluminates to indicate activation.

● Temperature and air distributionare set automatically and the fanruns at high speed.

● Switch on heated rear window Ü.● To return to previous mode:

press V, to return to automaticmode: press AUTO.

Setting of automatic rear windowheating can be changed in theInfo-Display. Vehicle personalisation3 98.

NoticeIf V is pressed while the engine isrunning, an Autostop will be inhibiteduntil V is pressed again.If s is pressed with the fan switchedon and the engine running, anAutostop will be inhibited until s ispressed again or until the fan isswitched off.If V is pressed while the engine isin an Autostop, the engine will restartautomatically.If s is pressed with the fan switchedon while the engine is in anAutostop, the engine will restartautomatically.


Manual settingsClimate control system settings canbe changed by activating the buttonsand rotary knobs as follows.Changing a setting will deactivate theautomatic mode.

Climate control 119

Fan speed Z

Turn left rotary knob to decrease orincrease fan speed. The fan speed isindicated in the Info-Display.Turning knob to $: fan and coolingare switched off.To return to automatic mode: PressAUTO.

Air distribution

Turn right rotary knob for desiredadjustment. Setting is indicated in theInfo-Display.K : to foot well and windscreen9 : to windscreen, front door

windows and foot wells : to windscreen and front door

windows (air conditioning isactivated in the background tohelp preventing windows fromfogging)

M : to head area via adjustable airvents

L : to head area and foot well

Return to automatic air distribution:press AUTO.

Cooling n

Press n to switch on cooling. TheLED in the button illuminates toindicate activation. Cooling is onlyfunctional when the engine is runningand climate control fan is switched on.Press n again to switch off cooling.The air conditioning system cools anddehumidifies (dries) as soon as theoutside temperature is slightly abovethe freezing point. Thereforecondensation may form and drip fromunder the vehicle.

120 Climate control

If no cooling or drying is required,switch off the cooling system for fuelsaving reasons.When the cooling system is switchedoff, no engine restart will berequested by the climate controlsystem during an Autostop.Exception: defrost system is activatedand outside temperature above 0 °Crequests a restart.Stop-start system 3 126.The status of cooling operation isindicated in the Info-Display.Activation or deactivation of coolingoperation after engine start can bechanged in the Info-Display. Vehiclepersonalisation 3 98.

Air recirculation mode 4

Press 4 to activate air recirculationmode. The LED in the buttonilluminates to indicate activation.Press 4 again to deactivaterecirculation mode.

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up from inside.The quality of the passenger

compartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen may mistup from outside, when cold air isdirected to it. If windscreen mists upfrom outside, activate windscreenwiper and deactivate s.

Basic settingsSome settings can be changed in theInfo-Display. Vehicle personalisation3 98.

Climate control 121

Air ventsAdjustable air ventsAt least one air vent must be openwhile the cooling is on.

Adjust the air amount at the ventoutlet by turning the adjuster wheel.The vent is closed when the adjusterwheel is turned close to the left orright.

Direct the flow of air by tilting andswivelling the slats.

9 Warning

Do not attach any objects to theslats of the air vents. Risk ofdamage and injury in case of anaccident.

Fixed air ventsAdditional air vents are locatedbeneath the windscreen and doorwindows and in the foot wells.

MaintenanceAir intake

The air intake in front of thewindscreen in the enginecompartment must be kept clear toallow air intake. Remove any leaves,dirt or snow.

Pollen filterThe pollen filter cleans dust, soot,pollen and spores from the airentering the vehicle through the airintake.

122 Climate control

Air conditioning regularoperationIn order to ensure continuouslyefficient performance, cooling mustbe operated for a few minutes once amonth, irrespective of the weatherand time of year. Operation withcooling is not possible when theoutside temperature is too low.

ServiceFor optimal cooling performance, it isrecommended to annually check theclimate control system, startingthree years after initial vehicleregistration, including:● functionality and pressure test● heating functionality● leakage check● check of drive belts● cleaning of condenser and

evaporator drainage● performance check

Driving and operating 123

Driving andoperating

Driving hints ............................... 123Control of the vehicle ............... 123Steering ................................... 124

Starting and operating ............... 124New vehicle running-in ............ 124Ignition switch positions ........... 124Retained power off .................. 124Starting the engine .................. 125Overrun cut-off ........................ 125Stop-start system .................... 126Parking .................................... 128

Engine exhaust .......................... 129Catalytic converter ................... 129

Manual transmission .................. 130Manual transmission automa‐ted .............................................. 130

Transmission display ............... 131Starting the engine .................. 131Selector lever .......................... 131Manual mode ........................... 133Electronic driving programmes 133Fault ........................................ 133

Brakes ........................................ 134Antilock brake system ............. 134Parking brake .......................... 135Brake assist ............................. 135Hill start assist ......................... 135

Ride control systems ................. 136Traction Control system .......... 136Electronic Stability Control ...... 137City mode ................................ 138

Driver assistance systems ......... 139Cruise control .......................... 139Speed limiter ........................... 141Parking assist .......................... 142Side blind spot alert ................. 151

Fuel ............................................ 153Fuel for petrol engines ............. 153Fuel for liquid gas operation .... 153Refuelling ................................ 155Fuel consumption - CO2-Emissions .............................. 158

Driving hintsControl of the vehicleNever coast with engine notrunningMany systems will not function in thissituation (e.g. brake servo unit, powersteering). Driving in this manner is adanger to yourself and others.All systems function during anAutostop.Stop-start system 3 126.

Idle boostIf charging of the vehicle battery isrequired due to battery condition, thepower output of the generator mustbe increased. This will be achieved byan idle boost which may be audible.A message appears on the Uplevel-Display.

PedalsTo ensure the pedal travel isuninhibited, there must be no mats inthe area of the pedals.

124 Driving and operating

Use only floor mats, which fit properlyand are fixed by the retainers on thedriver side.

SteeringIf power steering assist is lostbecause the engine stops or due to asystem malfunction, the vehicle canbe steered but may require increasedeffort.Control indicator c 3 86.

Starting and operatingNew vehicle running-inDo not brake unnecessarily hard forthe first few journeys.During the first drive, smoke mayoccur because of wax and oilevaporating off the exhaust system.Park the vehicle in the open for awhile after the first drive and avoidinhaling the fumes.During the running-in period fuel andengine oil consumption may behigher.Autostop may be inhibited to allow forcharging the vehicle battery.

Ignition switch positions

0 : ignition off1 : steering wheel lock released,

ignition off2 : ignition on3 : starting

Retained power offThe following electronic systems canwork until the driver's door is openedor at the latest for ten minutes afterthe ignition is switched off:● power windows● power outlets● power sunroof


Power to the Infotainment system willcontinue to operate for 30 minutes oruntil the key is removed from theignition switch, regardless of whetherany door is opened.

Starting the engine

Turn key to position 1 to release thesteering wheel lock.Manual transmission: operate clutchand brake pedal.Manual transmission automated:operate brake pedal.Do not operate the accelerator pedal.

Turn key briefly to position 3 andrelease: an automatic procedureoperates the starter after a briefdelay, until the engine is running. See'Automatic Starter Control'.Before restarting or to switch off theengine, turn the key back to position0.During an Autostop, the engine canbe started by depressing the clutchpedal.

Starting the vehicle at lowtemperaturesThe start of the engine withoutadditional heaters is possible down to-30 °C. Required is an engine oil withthe correct viscosity, the correct fuel,performed services and a sufficientlycharged vehicle battery.

Automatic starter controlThis function controls the enginestarting procedure. The driver doesnot need to hold the key in position 3.Once applied, the system will go onstarting automatically until the engine

is running. Because of the checkingprocedure, the engine starts runningafter a short delay.Possible reasons for a non-startingengine:● clutch pedal is not operated

(manual transmission).● brake pedal not operated

(manual transmissionautomated).

● timeout occurred.

Turbo engine warm-upUpon start-up, engine availabletorque may be limited for a short time,especially when the enginetemperature is cold. The limitation isto allow the lubrication system to fullyprotect the engine.

Overrun cut-offThe fuel supply is automatically cut offduring overrun, i.e. when the vehicleis driven with a gear engaged butaccelerator is released.


Stop-start systemThe stop-start system helps to savefuel and to reduce the exhaustemissions. When conditions allow, itswitches off the engine as soon as thevehicle is at a low speed or at astandstill, e.g. at a traffic light or in atraffic jam.On vehicles with manualtransmission, the engine is startedautomatically as soon as the clutch isdepressed.On vehicles with manual transmissionautomated, the engine is startedautomatically as soon as the brakepedal is released.A vehicle battery sensor ensures thatan Autostop is only performed if thevehicle battery is sufficiently chargedfor a restart.

ActivationThe stop-start system is available assoon as the engine is started, thevehicle starts-off and the conditionsas stated below in this section arefulfilled.

Deactivation

Deactivate the stop-start systemmanually by pressing eco. Thedeactivation is indicated when theLED in the button extinguishes.

AutostopVehicles with manual transmission:If the vehicle is at a low speed or at astandstill, activate an Autostop asfollows:● Depress the clutch pedal.● Move the selector lever to

neutral.● Release the clutch pedal.

The engine will be switched off whilethe ignition stays on.Vehicles with manual transmissionautomated:If the vehicle is at a standstill withdepressed brake pedal, Autostop isactivated automatically.The engine will be switched off whilethe ignition stays on.The stop-start system will be disabledon inclines of 15% or more.

Indication

An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.


During an Autostop, the heating andbrake performance will bemaintained.

Conditions for an AutostopThe stop-start system checks if eachof the following conditions is fulfilled:● The stop-start system is not

manually deactivated.● The bonnet is fully closed.● The driver's door is closed or the

driver's seat belt is fastened.● The vehicle battery is sufficiently

charged and in good condition.● The engine is warmed up.● The engine coolant temperature

is not too high.● The engine exhaust temperature

is not too high, e.g. after drivingwith high engine load.

● The ambient temperature isabove -5 °C.

● The climate control systemallows an Autostop.

● The brake vacuum is sufficient.● The vehicle was driven at least at

walking speed since the lastAutostop.

Otherwise an Autostop will beinhibited.Certain settings of the climate controlsystem may inhibit an Autostop. See'Climate control' chapter for moredetails 3 116.Immediately after motorway driving,an Autostop may be inhibited.New vehicle running-in 3 124.

Vehicle battery discharge protectionTo ensure reliable engine restarts,several vehicle battery dischargeprotection features are implementedas part of the stop-start system.

Power saving measuresDuring an Autostop, several electricalfeatures, e.g. the rear windowheating, are disabled or switched intoa power saving mode. The fan speedof the climate control system isreduced to save power.

Restart of the engine by the driverVehicles with manual transmission:Depress the clutch pedal to restart theengine.The engine start is indicated by theneedle at the idle speed position inthe tachometer.If the selector lever is shifted out ofneutral before depressing the clutchfirst, control indicator - illuminatesor is shown as a symbol in the DriverInformation Centre.Control indicator - 3 85.Vehicles with manual transmissionautomated:Release the brake pedal or moveselector lever out of D to restart theengine.The engine start is indicated by theneedle at the idle speed position inthe tachometer.

Restart of the engine by the stop-start systemThe selector lever must be in neutralto enable an automatic restart.


If one of the following conditionsoccurs during an Autostop, theengine will be restarted automaticallyby the stop-start system:● The stop-start system is

manually deactivated.● The bonnet is opened.● The driver's seat belt is

unfastened and the driver's dooris opened.

● The engine temperature is toolow.

● The charging level of the vehiclebattery is below a defined level.

● The brake vacuum is notsufficient.

● The vehicle is driven at least atwalking speed.

● The climate control systemrequests an engine start.

● The air conditioning is manuallyswitched on.

If the bonnet is not fully closed, awarning message is displayed in theDriver Information Centre.

If an electrical accessory, e.g. aportable CD player, is connected tothe power outlet, a brief power dropduring restart might be noticeable.

Parking

9 Warning

● Do not park the vehicle on aneasily ignitable surface. Thehigh temperature of theexhaust system could ignite thesurface.

● Always apply the parkingbrake. Activate the parkingbrake without pressing therelease button. Apply as firmlyas possible on a downhill slopeor uphill slope. Depress brakepedal at the same time toreduce operating force.

● Switch off the engine.● If the vehicle is on a level

surface or uphill slope, engagefirst gear before removing theignition key. On an uphill slope,

turn the front wheels away fromthe kerb.If the vehicle is on a downhillslope, engage reverse gearbefore removing the ignitionkey. Turn the front wheelstowards the kerb.

● Close the windows and thesunroof.

● Remove the ignition key fromthe ignition switch. Turn thesteering wheel until thesteering wheel lock is felt toengage.For vehicles with manualtransmission automated, thekey can only be removed fromthe ignition switch when theparking brake is applied.

● Lock the vehicle.● Activate the anti-theft alarm

system.● The engine cooling fans may run

after the engine has beenswitched off 3 162.


Caution

After running at high enginespeeds or with high engine loads,operate the engine briefly at a lowload or run in neutral forapprox. 30 seconds beforeswitching off, in order to protectthe turbocharger.

NoticeIn the event of an accident withairbag deployment, the engine isturned off automatically if the vehiclecomes to a standstill within a certaintime.

Engine exhaust

9 Danger

Engine exhaust gases containpoisonous carbon monoxide,which is colourless and odourlessand could be fatal if inhaled.If exhaust gases enter the interiorof the vehicle, open the windows.Have the cause of the faultrectified by a workshop.Avoid driving with an open loadcompartment, otherwise exhaustgases could enter the vehicle.

Catalytic converterThe catalytic converter reduces theamount of harmful substances in theexhaust gases.

Caution

Fuel grades other than those listedon page 3 153 could damage thecatalytic converter or electroniccomponents.Unburnt petrol will overheat anddamage the catalytic converter.Therefore avoid excessive use ofthe starter, running the fuel tankdry and starting the engine bypushing or towing.

In the event of misfiring, unevenengine running, a reduction in engineperformance or other unusualproblems, have the cause of the faultrectified by a workshop as soon aspossible. In an emergency, drivingcan be continued for a short period,keeping vehicle speed and enginespeed low.


Manual transmission

To engage reverse, depress theclutch pedal and press the releasebutton on the selector lever andengage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Do not slip the clutch unnecessarily.When operating, depress the clutchpedal completely. Do not use thepedal as a foot rest.

Caution

It is not advisable to drive with thehand resting on the selector lever.

Gear shift indication 3 86.Stop-start system 3 126.

Manual transmissionautomatedThe automated manual transmissionpermits manual gearshifting (manualmode) or automatic gearshifting(automatic mode), both withautomatic clutch control.Manual shifting is possible by tappingthe selector lever in manual mode.NoticeWhen unlocking or opening avehicle door, a sound may beaudible caused by the hydraulicsystem.


Transmission display

In automatic mode, the drivingprogramme is indicated by D in theDriver Information Centre.In manual mode, M and the numberof the selected gear is indicated.R indicates reverse gear.N indicates neutral.

Starting the engineTo start the engine, depress the brakepedal, if transmission is not in N.Transmission automatically shifts toN upon starting. There may be a slightdelay.

Starting is not possible if all brakelights fail.

Stop-start-system

AutostopIf the vehicle is at a standstill andbrake pedal is operated, Autostop isactivated automatically.The engine will be switched off whilethe ignition stays on.

An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.

AutostartRelease the brake pedal or moveselector lever out of D to restart theengine.The engine restart is indicated by theneedle at the idle speed position inthe tachometer.The stop-start system will be disabledon inclines of 15% or more.Stop-start-system 3 126.

Selector lever


Always move the selector lever in theappropriate direction as far as it willgo. Upon release, it automaticallyreturns to the centre position.N : neutral positionD/M : switch between automatic (D)

and manual (M) shift mode.The transmission displayshows either D or M with theselected gear

< : upshifting in manual mode] : downshifting in manual modeR : reverse gear. Engage only

when vehicle is stationary

If selector lever is moved from R to theleft, D is directly engaged.If selector lever is moved from D to< or ], the manual mode M isselected and the transmission shifts.

Starting offDepress the brake pedal and movethe selector lever to D/M or R. If D isselected, transmission is in automaticmode and first gear is engaged. If Ris selected, reverse gear is engaged.The vehicle starts to move when thebrake is released.

To start-off without depressing thefoot brake, accelerate immediatelyafter engaging a gear as long as D orR flashes.If neither the accelerator nor thebrake pedal are depressed, no gearis engaged and D or R flashes for abrief time in the display.

Stopping the vehicleIn D, first gear is engaged and theclutch is released when the vehicle isstopped. In R, reverse gear remainsengaged.

Engine braking

Automatic modeWhen driving downhill, the manualtransmission automated does notshift into higher gears until a fairlyhigh engine speed has been reached.It shifts down in good time whenbraking.

Manual modeTo utilise the engine braking effect,select a lower gear in good time whendriving downhill. Changing into

manual mode is only possible whilethe engine is running or during anAutostop.

Rocking the vehicleRocking the vehicle is onlypermissible if the vehicle is stuck insand, mud or snow. Move the selectorlever between R and D in a repeatpattern. Do not race the engine andavoid sudden acceleration.

ParkingThe most recently engaged gear (seetransmission display) remainsengaged when switching off ignition.With N, no gear is engaged.Therefore always apply the parkingbrake when switching off ignition. Ifparking brake is not applied, P flashesin the transmission display and thekey cannot be removed from theignition switch. P stops flashing in thetransmission display as soon as theparking brake is slightly applied.When the ignition is switched off, thetransmission no longer responds tomovement of the selector lever.


Tyre pressure monitoring systemTo start the sensor matching processof the tyre pressure monitoringsystem, the selector lever must bemoved and held in position N forfive seconds. P illuminates in thetransmission display to indicate thatthe sensor matching process can bestarted.Tyre pressure monitoring system3 185.

Manual modeIf a higher gear is selected when theengine speed is too low, or a lowergear when the speed is too high, theshift is not executed. This preventsthe engine from running at too low ortoo high an engine speed. A warningmessage is displayed in the DriverInformation Centre. Vehiclemessages 3 95.If engine speed is too low, thetransmission automatically shifts to alower gear.If engine speed is too high, thetransmission only switches to a highergear via kickdown.

When + or - is selected in automaticmode, the transmission switches tomanual mode and shifts accordingly.

Gear shift indicationThe symbol R, with a numberalongside it, is indicated whengearshifting is recommended for fuelsaving reasons.Shift indication appears only inmanual mode.

Electronic drivingprogrammes● Following a cold start, the

operating temperatureprogramme increases enginespeed to quickly bring thecatalytic converter to the requiredtemperature.

● The adaptive programme tailorsgearshifting to the drivingconditions, e.g. greater load orgradients.

KickdownIf the accelerator pedal is presseddown completely in automatic mode,the transmission shifts to a lower geardepending on engine speed.

FaultTo prevent damage to the manualtransmission automated, the clutch isengaged automatically at high clutchtemperatures.In the event of a fault, control indicatorg illuminates. Additionally, awarning message is displayed in theDriver Information Centre. Vehiclemessages 3 95.Continued driving is restricted or notpossible, depending on the fault.Have the cause of the fault remediedby a workshop.


BrakesThe brake system comprises twoindependent brake circuits.If a brake circuit fails, the vehicle canstill be braked using the other brakecircuit. However, braking effect isachieved only when the brake pedalis depressed firmly. Considerablymore force is needed for this. Thebraking distance is extended. Seekthe assistance of a workshop beforecontinuing the journey.When the engine is not running, thesupport of the brake servo unitdisappears once the brake pedal hasbeen depressed once or twice.Braking effect is not reduced, butbraking requires significantly greaterforce. It is especially important to bearthis in mind when being towed.Control indicator R 3 85.

Antilock brake systemAntilock brake system (ABS)prevents the wheels from locking.

ABS starts to regulate brake pressureas soon as a wheel shows a tendencyto lock. The vehicle remainssteerable, even during hard braking.ABS control is made apparentthrough a pulse in the brake pedaland the noise of the regulationprocess.For optimum braking, keep the brakepedal fully depressed throughout thebraking process, despite the fact thatthe pedal is pulsating. Do not reducethe pressure on the pedal.After starting off the system performsa self-test which may be audible.Control indicator u 3 86.

Adaptive brake lightDuring full braking, all three brakelights flash for the duration of ABScontrol.

Fault

9 Warning

If there is a fault in the ABS, thewheels may be liable to lock dueto braking that is heavier thannormal. The advantages of ABSare no longer available. Duringhard braking, the vehicle can nolonger be steered and mayswerve.

Have the cause of the fault remediedby a workshop.


Parking brakeManual parking brake

9 Warning

Always apply parking brake firmlywithout operating the releasebutton, and apply as firmly aspossible on a downhill or uphillslope.To release the parking brake, pullthe lever up slightly, press therelease button and fully lower thelever.

To reduce the operating forces ofthe parking brake, depress thebrake pedal at the same time.

Control indicator R 3 85.

Brake assistIf the brake pedal is depressedquickly and forcefully, maximumbrake force is automatically applied(full braking).Maintain steady pressure on thebrake pedal for as long as full brakingis required. Maximum brake force isautomatically reduced when thebrake pedal is released.

Hill start assistThe system helps prevent unintendedmovement when driving away oninclines.When releasing the brake pedal afterstopping on an incline, the brakesremain on for a further two seconds.The brakes release automatically as

soon as the vehicle begins toaccelerate or the two seconds holdingtime is over.The hill start assist is not active duringan Autostop.


Ride control systemsTraction Control systemThe Traction Control system (TC) is acomponent of the Electronic StabilityControl (ESC).TC improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip, bypreventing the drive wheels fromspinning.As soon as the drive wheels starts tospin, engine output is reduced andthe wheel spinning the most is brakedindividually. This considerablyimproves the driving stability of thevehicle on slippery road surfaces.

TC is operational after each enginestart as soon as control indicator bextinguishes.When TC operates b flashes.

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Deactivation

TC can be switched off when spinningof drive wheels is required: press bbriefly.A status message appears in theDriver Information Centre when TC isdeactivated.When TC is deactivated, ESCremains active.TC is reactivated by pressing bagain. A status message pops up inthe Driver Information Centre whenTC is reactivated.TC is also reactivated the next timethe ignition is switched on.


FaultIf there is a fault in the system thecontrol indicator b illuminatescontinuously and a message or awarning code appears in the DriverInformation Centre. The system is notoperational.Have the cause of the fault remediedby a workshop.

Electronic Stability ControlElectronic Stability Control (ESC)improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip.As soon as the vehicle starts toswerve (understeer/oversteer),engine output is reduced and thewheels are braked individually.ESC operates in combination with theTraction Control system (TC). Itprevents the drive wheels fromspinning.

ESC is operational after each enginestart as soon as control indicator bextinguishes.When ESC operates b flashes.

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator b 3 86.

Deactivation

ESC and TC can be deactivated:● hold b pressed for a minimum of

five seconds: ESC and TC areboth deactivated. t illuminatesand status messages appear inthe Driver Information Centre.


● To deactivate only Tractioncontrol system press b briefly:TC is inactive but ESC remainsactive. A status messageappears in the Driver InformationCentre when TC is deactivated.

If the vehicle reaches the stabilitythreshold with deactivated ESC, thesystem will automatically reactivateESC for the time duration of thethreshold, when the brake pedal isdepressed once.ESC is reactivated by pressing bagain. If the TC system waspreviously disabled, both TC andESC are reactivated. A statusmessage pops up in the Driver

Information Centre and textinguishes when TC and ESC arereactivated.ESC is also reactivated the next timethe ignition is switched on.

FaultIf there is a fault in the system thecontrol indicator b illuminatescontinuously and a message or awarning code appears in the DriverInformation Centre. The system is notoperational.Have the cause of the fault remediedby a workshop.

City modeCity mode is a feature which enablesincreased steering assistance duringlower speed conditions, e.g. citytraffic or parking. Steering assistanceis increased for greater convenience.

Activation

Press B when engine is running. Thesystem works from standstill up to22 mph, and in reverse gear. Abovethis speed the system changes tonormal mode. When activated, Citymode engages automatically below22 mph.An illuminated LED in the City modebutton indicates that the system isactive.Additionally, a message pops-up inthe Driver Information Centre.City mode remains active during anAutostop, but is only operationalwhen the engine is running.



DeactivationPress B; LED in the buttonextinguishes and a message pops-upin the Driver Information Centre.Each time the engine is started, Citymode is deactivated.

Fault

In the event of a fault in the system,c illuminates and a message isdisplayed in the Driver InformationCentre.Vehicle messages 3 95.

System calibrationIf control indicators c and billuminate simultaneously, acalibration of the power steeringsystem is necessary. This can occure.g. when turning the steering wheelfor one rotation with ignition switchedoff. In this case switch on ignition andturn steering wheel once from lock tolock.If control indicators c and b do notextinguish after calibration, seek theassistance of a workshop.

Driver assistancesystems

9 Warning

Driver assistance systems aredeveloped to support the driverand not to replace the driver'sattention.The driver accepts fullresponsibility when driving thevehicle.When using driver assistancesystems, always take careregarding the current trafficsituation.

Cruise controlThe cruise control can store andmaintain speeds of approx. 20 mph tomaximum vehicle speed. Deviationsfrom the stored speeds may occurwhen driving uphill or downhill.For safety reasons the cruise controlcannot be activated until the brakepedal has been operated once.Activating in first gear is not possible.


Do not use the cruise control if it is notadvisable to maintain a constantspeed.On vehicles with manual transmissionautomated cruise control can beactivated in automatic mode andmanual mode.Control indicator m 3 88.

Switching onPress m; control indicator m ininstrument cluster illuminates white.

ActivationAccelerate to the desired speed andturn thumb wheel to SET/-, thecurrent speed is stored andmaintained. Control indicator m ininstrument cluster illuminates green.Accelerator pedal can be released.Vehicle speed can be increased bydepressing the accelerator pedal.When the accelerator pedal isreleased, the previously stored speedis resumed.Cruise control remains activatedwhile gearshifting.

Increase speedWith cruise control active, hold thumbwheel turned to RES/+ or briefly turnto RES/+ repeatedly: speedincreases continuously or in smallincrements.Alternatively accelerate to the desiredspeed and store by turning to SET/-.

Reduce speedWith cruise control active, hold thumbwheel turned to SET/- or briefly turn toSET/- repeatedly: speed decreasescontinuously or in small increments.

DeactivationPress y; control indicator m ininstrument cluster illuminates white.Cruise control is deactivated. Laststored speed remains in memory forlater speed resume.


Automatic deactivation:● Vehicle speed is below approx.

20 mph.● Vehicle speed drops more than

15 mph below the set speed.● The brake pedal is depressed.● The clutch pedal is depressed for

a few seconds.● The selector lever is in N.● Engine speed is in a very low

range.● The Traction Control system or

Electronic Stability Control isoperating.

● Simultaneous pressing RES/+and brake pedal deactivatescruise control and will deletestored speed.

Resume stored speedTurn thumb wheel to RES/+ at aspeed above 20 mph. The storedspeed will be obtained.

Switching offPress m; control indicator m ininstrument cluster extinguishes. Thestored speed is deleted.Pressing L to activate the speedlimiter or switching off the ignition alsoswitches off cruise control anddeletes the stored speed.

Speed limiterThe speed limiter prevents thevehicle exceeding a preset maximumspeed.The maximum speed can be set atspeeds above 15 mph up to125 mph.The driver can only accelerate up tothe preset speed. Deviations from thelimited speed may occur when drivingdownhill.The preset speed limit is displayed inthe Driver Information Centre whenthe system is active.

Activation

Press L. If cruise control has beenactivated before, it is switched offwhen speed limiter is activated andthe control indicator m extinguishes.

Set speed limitAccelerate to the desired speed andbriefly turn thumb wheel to SET/-: thecurrent speed is stored as maximumspeed. Speed limit is displayed in theDriver Information Centre.


Change speed limitWith speed limiter active, turn thumbwheel to RES/+ to increase or SET/-to decrease the desired maximumspeed.

Exceeding the speed limitWhen exceeding the limited speedwithout driver input, the speed willflash in the Driver Information Centreand a chime sounds during thisperiod.

In the event of an emergency, it ispossible to exceed the speed limit bydepressing the accelerator pedalfirmly nearly to the final point. In thiscase no chime appears.Release the accelerator pedal andthe speed limiter function isreactivated once a speed lower thanthe limit speed is obtained.

DeactivationPress y: speed limiter is deactivatedand the vehicle can be driven withoutspeed limit.The limited speed is stored.Additionally, a correspondingmessage appears on the Uplevel-Display.

Resume limit speedTurn thumb wheel to RES/+. Thestored speed limit will be obtained.

Switching offPress L, the speed limit indication inthe Driver Information Centreextinguishes. The stored speed isdeleted.

By pressing m to activate cruisecontrol, speed limiter is alsodeactivated and the stored speed isdeleted.By switching off the ignition, speedlimiter is also deactivated, but thespeed limit will be stored for nextspeed limiter activation.

Parking assistRear parking assist

9 Warning

It is the driver who bears fullresponsibility for the parkingmanoeuvre.Always check the surroundingarea while reversing and using therear parking assist system.

The rear parking assist makesparking easier by measuring thedistance between the vehicle andrear obstacles. It informs and warnsthe driver by giving acoustic andvisual signals.


The system has four ultrasonicparking sensors in the rear bumper.

ActivationWhen reverse gear is engaged, thesystem is ready to operateautomatically.An illuminated LED in the parkingassist button r indicates that thesystem is ready to operate.

IndicationThe system warns the driver withacoustic signals against potentiallyhazardous obstacles behind thevehicle in a distance range up to1.5 metres. The interval between the

sounds becomes shorter as thevehicle gets closer to that obstacle.When the distance is less thanapproximately 30 cm, the sound iscontinuous.Additionally, the distance to rearobstacles is displayed by changingdistance lines in the DriverInformation Centre 3 88 or,depending on the version, on theColour-Info-Display 3 93.

Deactivation

The system automatically switchesoff when reverse gear is disengaged.

Manual deactivation is also possibleby pressing the parking assist buttonr.In both cases the LED in the buttonextinguishes.

FaultIn the event of a fault or if the systemdoes not work temporarily, e.g.because of high external noise levelor other interference factors, the LEDin the button flashes for threeseconds and then extinguishes.Control indicator r illuminates inthe instrument cluster 3 86 and amessage pops-up in the DriverInformation Centre.

Front-rear parking assist

9 Warning

The driver bears full responsibilityfor the parking manoeuvre.Always check the surroundingarea when driving backwards orforwards while using parkingassist system.


The front-rear parking assistmeasures the distance between thevehicle and obstacles in front andbehind the vehicle. It informs andwarns the driver by giving acousticsignals and display indication.

The system has six ultrasonic parkingsensors in both the rear and frontbumper.It uses two different acoustic warningsignals for the front and rearmonitoring areas, each with adifferent tone frequency.

Front-rear parking assist is alwayscombined with advanced parkingassist, see "Advanced parking assist"section below.

Parking assist button D andoperation logic

Front-rear parking assist andadvanced parking assist both use thesame button for activation anddeactivation:A brief press of D activates ordeactivates the parking assist.

A long press of D (approx.one second) activates or deactivatesthe advanced parking assist, seeseparate description.Button logic operates the systems bypressing D as follows:● If only front-rear parking assist is

active, a brief press deactivatesfront-rear parking assist.

● If only front-rear parking assist isactive, a long press activatesadvanced parking assist.

● If only advanced parking assist isactive and the system is inparking slot searching mode, abrief press activates front-rearparking assist.

● If only advanced parking assist isactive and the system is in parkguiding mode, a brief pressdeactivates advanced parkingassist.

● If advanced parking assist isactive, a long press deactivatesadvanced parking assist andfront-rear parking assist.


● If a forward gear or neutral isselected, a brief press activatesor deactivates only front parkingassist.

● If reverse gear is selected, a briefpress activates or deactivatesfront and rear parking assist.

ActivationThe system is activated automaticallyat a speed up to 7 mph.An illuminated LED in the parkingassist button D indicates that thesystem is ready to operate.If D is switched off within an ignitioncycle, the front parking assist isdeactivated. If vehicle speed hasexceeded 15 mph beforehand,parking assist will be reactivatedwhen speed drops below 7 mph.When the system is deactivated, theLED in the button extinguishes andPark Assist Off pops-up in the DriverInformation Centre.

IndicationThe system warns the driver withacoustic signals against potentiallyhazardous obstacles in front of the

vehicle in a distance range up to 80cm and against potentially hazardousobstacles behind the vehicle in adistance range up to 1.5 metres.Depending on which side of thevehicle is closer to an obstacle, youwill hear acoustic warning signals inthe vehicle on the respective side.The interval between the soundsbecomes shorter as the vehicle getscloser to that obstacle. When thedistance is less than approx. 30 cm,the sound is continuous.Additionally, the distance to obstaclesis shown in the Driver InformationCentre 3 88 or, depending on theversion, on the Colour-Info-Display3 93.

The distance to a front and rearobstacle is displayed by changingdistance lines in the DriverInformation Centre.The distance indication can beinhibited by vehicle messages with ahigher priority. After dismissing themessage distance indication appearsagain.


The distance to obstacles is shown onthe Colour-Info-Display by colouredzones in front of or behind the vehicle3 93.

DeactivationThe system is deactivatedautomatically when vehicle speedexceeds 7 mph.Manual deactivation is also possibleby pressing the parking assist buttonD.When the system is deactivated, theLED in the button extinguishes andand, if manual deactivated,ParkAssist Off pops-up in the DriverInformation Centre.

After a manual deactivation, the front-rear parking assist is activated againif D is pressed.The complete system can bemanually deactivated in the vehiclepersonalisation menu in theInfo-Display. It remains deactivatedduring the ignition cycle or untilactivation in personalisation menuagain. Vehicle personalisation 3 98.

FaultIn the event of a fault or if the systemdoes not work temporarily, e.g.because of high external noise levelor other interference factors, amessage pops-up in the DriverInformation Centre.Vehicle messages 3 95.

Advanced parking assist

9 Warning

The driver bears full responsibilityfor accepting the parking slotsuggested by the system and theparking manoeuvre.

Always check the surroundingarea in all directions when usingthe advanced parking assist.

The advanced parking assistmeasures a suitable parking slotwhile passing, calculates thetrajectory and automatically steersthe vehicle into a parallel orperpendicular parking slot.Instructions are given in the DriverInformation Centre 3 88 or,depending on the version, on theColour-Info-Display 3 93, supportedby acoustic signals.The driver must control acceleration,braking and gearshifting, whilesteering is done automatically.Advanced parking assist can only beactivated when driving forwards.


Advanced parking assist is alwayscombined with front-rear parkingassist, see previous section. Bothsystems use the same sensors in thefront and rear bumper.

Button D and operation logicAdvanced parking assist and front-rear parking assist both use the samebutton for activation and deactivation:A brief press of D activates ordeactivates the parking assist.A long press of D (approx.one second) activates or deactivatesthe advanced parking assist, seeseparate description below.

Button logic operates the systems bypressing D as follows:● If only front-rear parking assist is

active, a brief press deactivatesfront-rear parking assist.

● If only front-rear parking assist isactive, a long press activatesadvanced parking assist.

● If only advanced parking assist isactive and the system is inparking slot searching mode, abrief press activates front-rearparking assist.

● If only advanced parking assist isactive and the system is in parkguiding mode, a brief pressdeactivates advanced parkingassist.

● If advanced parking assist isactive, a long press deactivatesadvanced parking assist andfront-rear parking assist.

● If forward gear or neutral isselected, a brief press activatesor deactivates front parkingassist.

● If reverse gear is selected, a briefpress activates or deactivatesfront and rear parking assist.

Activation

When searching for a parking slot, thesystem is ready to operate with a longpress of D.The system recognises andmemorises ten metres for parallelparking slots or six metres forperpendicular parking slots in theparking assist mode.


The system can only be activated ata speed up to 18 mph and the systemsearches for a parking slot at a speedup to 18 mph.The maximum allowed paralleldistance between the vehicle and arow of parked cars is 1.8 metres forparallel parking and 2.5 metres forperpendicular parking.

FunctionalityParking slot searching modeIndication in the Driver InformationCentre

Select parallel or perpendicularparking slot in Driver InformationCentre by pressing SET/CLR.The system is configured to detectparking slots by default on thepassenger side. To detect parkingslots on the driver side, switch on turnsignal indicator on the driver side.

When a slot is detected, visualfeedback in the Driver InformationCentre and an acoustic signal aregiven.Indication in the Colour-Info-Display


Select parallel or perpendicularparking slot by tapping the respectiveicon on the display.Select parking side by tapping therespective icon on the display.

When a slot is detected, visualfeedback on the Colour-Info-Displayand an acoustic signal are given.If the driver does not stop the vehicleafter a parking slot is proposed, thesystem starts to search for anothersuitable parking slot.Park guiding modeThe parking slot suggestion of thesystem is accepted when the vehicleis stopped by the driver within ten

metres for parallel parking slots or sixmetres for perpendicular parking slotsafter the Stop message is given. Thesystem calculates the optimal pathinto the parking slot.A brief vibration in the steering wheelafter engaging reverse gear indicatesthat the steering is controlled by thesystem. Then the vehicle is steeredinto the slot automatically by givingthe driver detailed instructions forbraking, accelerating andgearshifting. The driver must keephands away from the steering wheel.Always pay attention to the sound ofthe front-rear parking assist.Continuous sound indicates that thedistance to an obstacle is less thanapprox. 30 cm.If, for any reason, the driver must takeover control of the steering, hold thesteering wheel only at the outer edge.Automatic steering is cancelled in thisevent.

Display indicationThe instructions in the display show:● general hints and warning

messages● a hint when driving faster than

18 mph during parking slotsearching mode, or 5 mph inguiding mode

● the demand to stop the vehicle,when a parking slot is detected

● the direction of driving during theparking manoeuvre

● the demand to gearshiftrearwards or forwards

● the demand to accelerate orbrake

● for some of the instructions aprogress bar is shown in theDriver Information Centre

● successful parking manoeuvreindicated by a pop-up symboland a chime,

● the cancelling of a parkingmanoeuvre


Display prioritiesAdvanced parking assist indication onthe Driver Information Centre can beinhibited by vehicle messages with ahigher priority. After approving themessage by pressing SET/CLR onthe turn signal lever, advancedparking assist instructions appearagain and the parking manoeuvre canbe continued.

DeactivationThe system is deactivated by:● a long press of D● parking manoeuvre successfully

ended● driving faster than 18 mph during

parking slot search● driving faster than 5 mph during

parking guidance● driver interference on steering

wheel detected● exceeding the maximum number

of gear changes: eight parkingcycles when parallel parking orfive cycles when perpendicularparking

● switching off the ignition

Deactivation by the driver or by thesystem during manoeuvring will beindicated by Parking Deactivated onthe display. Additionally, an acousticsignal sounds.

FaultA message appears when:● there is a fault in the system● the driver did not successfully

complete the parking manoeuvre● the system is not operational● any of the deactivation reasons

described above applyIf an object is detected during parkinginstructions, Stop is indicated on thedisplay. Removing the object willresume the parking manoeuvre. If theobject is not removed, the system willbe deactivated. A long press of Dwill activate the system and search fora new parking slot.

Basic notes on parking assistsystems

9 Warning

Under certain circumstances,various reflective surfaces onobjects or clothing as well asexternal noise sources may causethe system to fail to detectobstacles.Special attention must be paid tolow obstacles which can damagethe lower part of the bumper.

Caution

Performance of the system can bereduced when sensors arecovered, e.g. by ice or snow.Performance of the parking assistsystem can be reduced due toheavy loading.Special conditions apply if thereare taller vehicles in the vicinity(e.g. off-road vehicles, mini vans,vans). Object identification and


correct distance indication in theupper part of these vehiclescannot be guaranteed.Objects with a very small reflectioncross-section, e.g. objects ofnarrow size or soft materials, maynot be detected by the system.Parking assist systems do notdetect objects outside thedetection range.

NoticeIt is possible that the sensor detectsa non-existing object caused byecho disturbance from externalacoustic noise or mechanicalmisalignments (sporadic falsewarnings may occur).Make sure that the front numberplate is properly mounted (not bentand no gaps to the bumper on the leftor right side) and the sensors arefirmly in place.Advanced parking assist systemmay not respond to changes in theavailable parking space afterinitiating a parking manoeuvre. Thesystem may recognize an entry, a

gateway, a courtyard or even acrossing as a parking slot. Afterselecting reverse gear the systemwill start a parking manoeuvre. Takecare regarding the availability of thesuggested parking slot.Surface irregularities, e.g. onconstruction zones, are not detectedby the system. The driver acceptsresponsibility.NoticeIf engaging a forward gear andexceeding a certain speed, the rearparking assist will be deactivatedwhen the rear carrier system isextended.If engaging reverse at first, theparking assist will detect the rearcarrier system and provide a buzzingsound. Press r or D briefly todeactivate the parking assist.NoticeAfter production, the systemrequires a calibration. For optimalparking guidance, a driving distanceof at least 6 miles, including anumber of bends, is required.

Side blind spot alertThe Side blind spot alert systemdetects and reports objects on eitherside of the vehicle, within a specified"blind spot" zone. The system alertsvisually in each exterior mirror, whendetecting objects that may not bevisible in the interior and exteriormirrors.Side blind spot alert uses some of theadvanced parking assist sensorswhich are located in the front and rearbumper on both sides of the vehicle.

9 Warning

Side blind spot alert does notreplace driver vision.The system does not detect:

● Vehicles outside the side blindzones which may be rapidlyapproaching.

● Pedestrians, cyclists oranimals.

Before changing a lane, alwayscheck all mirrors, look over theshoulder and use the turn signal.


When the system detects a vehicle inthe side blind zone while drivingforwards, either while passing avehicle or being passed, a yellowwarning symbol B will illuminate inthe relevant exterior mirror. If thedriver then activates the turn signal,the warning symbol B starts flashingyellow as a warning not to changelanes.NoticeIf the passing vehicle is at least6 mph faster than the passedvehicle, the warning symbol B in therelevant exterior mirror may notilluminate.

Side blind spot alert is active fromspeeds of 6 mph up to 87 mph.Driving faster than 87 mphdeactivates the system, indicated bylow lighting warning symbols B inboth exterior mirrors. Reducing thespeed again will extinguish thewarning symbols. If a vehicle is thendetected in the blind zone, thewarning symbols B will illuminate asnormal on the relevant side.When the vehicle is started, bothexterior mirror displays will brieflycome on to indicate that the system isoperating.The system can be activated ordeactivated in the Info-Display,vehicle personalisation 3 98.Deactivation is indicated by amessage in the Driver InformationCentre.

Detection zonesThe detection zones start at the rearbumper and extend approx. threemetres rearwards and to the sides.The height of the zone is betweenapprox. 0.5 metres and two metres offthe ground.

Side blind spot alert is designed toignore stationary objects, e.g.guardrails, posts, curbs, walls andbeams. Parked vehicles or oncomingvehicles are not detected.

FaultOccasional missed alerts can occurunder normal circumstances and willincrease in wet conditions.Side blind spot alert does not operatewhen the left or right corners of therear bumper are covered with mud,dirt, snow, ice, slush, or in heavyrainstorms. Cleaning instructions3 205.In the event of a fault in the system orif the system does not work due totemporary conditions, a message isdisplayed in the Driver InformationCentre. Seek the assistance of aworkshop.


FuelFuel for petrol enginesOnly use unleaded fuel that complieswith European standard EN 228 orE DIN 51626-1 or equivalent.The engine is capable of running withfuel that contains up to 10% ethanol(e.g. named E10).Use fuel with the recommendedoctane rating. The engine specificrequirements are given in the enginedata overview 3 217. A countryspecific label at the fuel filler flap cansupersede the requirement.

Caution

Do not use fuel or fuel additivesthat contain metallic compoundssuch as manganese-basedadditives. This may cause enginedamage.

Caution

Use of fuel that does not comply toEN 228 or E DIN 51626-1 orequivalent can lead to deposits orengine damage.

Caution

Use of fuel with too low an octanerating could lead to uncontrolledcombustion and engine damage.

Fuel for liquid gas operationLiquid gas is known as LPG(Liquefied Petroleum Gas) or underits French name GPL (Gaz de PétroleLiquéfié). LPG is also known asAutogas.LPG consists mainly of propane andbutane. The octane rating is between105 and 115, depending on thebutane proportion. LPG is storedliquid at around five to ten barpressure.

The boiling point depends on thepressure and mixing ratio. At ambientpressure, it is between -42 °C (purepropane) and -0.5 °C (pure butane).

Caution

The system works at an ambienttemperature of approx. -8 °C to100 °C.

Full function of the LPG system canonly be guaranteed with liquid gaswhich complies with the minimumrequirements of DIN EN 589.

Fuel selector


Pressing LPG switches betweenpetrol and liquid gas operation assoon as the required parameters(coolant temperature, gastemperature and minimum enginespeed) have been reached. Therequirements are usually fulfilled afterapprox. 60 seconds (depending onexterior temperature) and the first firmpress on the accelerator. The LEDstatus shows the current operatingmode.LED off : petrol operationLEDflashes

: checking conditions forfuel transition to liquidgas operation.Illuminates if conditionsare fulfilled.

LED illu‐minates

: liquid gas operation

LEDflashesfivetimesandextin‐guishes

: liquid gas tank is emptyor failure in liquid gassystem. A message isdisplayed in the DriverInformation Centre.

If the fuel tank is empty, the enginewill not start.

The selected fuel mode is stored andreactivated at the next ignition cycle ifconditions allow.As soon as the liquid gas tanks areempty, petrol operation isautomatically engaged until theignition is switched off.When switching automaticallybetween petrol or gas operation, abrief delay of engine tractive powermay be noticeable.Every six months, run the petrol tankdown until control indicator Yilluminates, then refuel. This helpsmaintain fuel quality and systemfunction for petrol operation.Fill the tank completely at regularintervals to prevent corrosion in thetank.

Faults and remediesIf gas mode is not possible, check thefollowing:● Is there enough liquid gas

present?● Is there enough petrol present for

starting?

Due to extreme temperatures incombination with the gascomposition, it may take slightlylonger before the system switchesfrom petrol to gas mode.In extreme situations, the system mayalso switch back to petrol mode if theminimum requirements are notfulfilled. If conditions allow, it might bepossible to manually switch back toliquid gas operation.Seek the assistance of a workshop inthe event of all other faults.

Caution

Repairs and adjustments may onlybe made by trained specialists inorder to maintain the safety andwarranty on the LPG system.

Liquid gas is given a particular odour(odorised) so that any leaks can bedetected easily.


9 Warning

If you smell gas in the vehicle or inthe immediate vicinity, switch topetrol mode immediately. Nosmoking. No naked flames orignition sources.

If the gas odour persists, do not startthe engine. Have the cause of thefault remedied by a workshop.When using underground car parks,follow the instructions of the operatorand local laws.NoticeIn the event of an accident, switch offthe ignition and lights.

Refuelling

9 Danger

Before refuelling, switch off theignition.Follow the operating and safetyinstructions of the filling stationwhen refuelling.

9 Danger

Fuel is flammable and explosive.No smoking. No naked flames orsparks.If you can smell fuel in yourvehicle, have the cause of thisremedied immediately by aworkshop.

Caution

In case of misfuelling, do notswitch on ignition.

Fuel filler flap is located at right rearside of the vehicle.

The fuel filler flap can only be openedwhen the vehicle is unlocked.Push the flap to engage. Then openthe flap.Turn the fuel filler cap slowlyanticlockwise to open.


The fuel filler cap can be retained inthe bracket on the fuel filler flap.To refuel, fully insert the pump nozzleand switch it on.After the automatic cut-off, the tankcan be topped up by operating thepump nozzle a maximum of two moretimes.

Caution

Wipe off any overflowing fuelimmediately.

To close, turn the fuel filler capclockwise until it clicks.Close the flap and allow it to engage.

Liquid gas refuellingFollow the operating and safetyinstructions of the filling station whenrefuelling.The filling valve for the liquid gas isbehind the fuel filler cap.

Unscrew protective cap from the fillerneck.

Screw the required adapter hand-tight onto the filler neck.


ACME Adapter: Screw the nut of thefilling nozzle onto the adapter. Presslocking lever on filler nozzle down.DISH filler neck: Place the filler nozzleinto the adapter. Press locking leveron filler nozzle down.Bayonet filler neck: Place filler nozzleon the adapter and turn clockwise oranticlockwise through one quarterturn. Pull locking lever of filler nozzlefully.EURO filler neck: Press the fillernozzle onto the adapter until itengages.Press the button at the liquid gassupply point. The filling system stopsor begins to run slowly when 80% ofthe tank volume is reached(maximum fill level).Release button on filling system andthe filling process stops. Release thelocking lever and remove the fillernozzle. A small quantity of liquid gasmay escape.Remove adapter and stow securely invehicle.

Fit protective cap to prevent thepenetration of foreign bodies into thefiller opening and the system.

9 Warning

Due to the system design, anescape of liquid gas afterreleasing the locking lever isunavoidable. Avoid inhaling.

9 Warning

The liquid gas tank should only befilled to 80% capacity, for safetyreasons.

The multivalve on the liquid gas tankautomatically limits the fill quantity. Ifa larger quantity is added, werecommend not exposing the vehicleto the sun until the excess amounthas been used up.

Filling adapterAs filling systems are notstandardised, different adapters arerequired which are available fromVauxhall Distributors and fromVauxhall Authorised Repairers.

ACME adapter: Belgium, Germany,Ireland, Luxembourg, Switzerland


Bayonet adapter: Netherlands,Norway, Spain, United Kingdom

EURO adapter: Spain

DISH adapter: Austria, Bosnia-Herzegovina, Bulgaria, Croatia,Czech Republic, Denmark, Estonia,France, Greece, Hungary, Italy,Latvia, Lithuania, Macedonia,Poland, Portugal, Romania, Serbia,Slovakia, Slovenia,Sweden,Switzerland, Turkey, Ukraine

Fuel filler capOnly use genuine fuel filler caps.

Fuel consumption - CO2-Emissions The fuel consumption (combined) ofthe model Vauxhall Adam is within arange of 40 to 67 mpg.The CO2 emission (combined) iswithin a range of 139 to 99 g/km.For the values specific for yourvehicle, refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.

General informationThe official fuel consumption andspecific CO2 emission figures quotedrelate to the EU base model withstandard equipment.Fuel consumption data and CO2emission data are determinedaccording to regulation R (EC)No. 715/2007 (in the latest applicableversion), taking into consideration thevehicle weight in running order, asspecified by the regulation.


The figures are provided only for thepurpose of comparison betweendifferent vehicle variants and mustnot be taken as a guarantee for theactual fuel consumption of aparticular vehicle. Additionalequipment may result in slightlyhigher results than the statedconsumption and CO2 figures.Furthermore, fuel consumption isdependent on personal driving styleas well as road and traffic conditions.

160 Vehicle care

Vehicle care

General Information ................... 160Accessories and vehiclemodifications .......................... 160

Vehicle storage ........................ 161End-of-life vehicle recovery ..... 161

Vehicle checks ........................... 162Performing work ...................... 162Bonnet ..................................... 162Engine oil ................................. 163Engine coolant ......................... 164Washer fluid ............................ 164Brakes ..................................... 165Brake fluid ............................... 165Vehicle battery ......................... 165Wiper blade replacement ........ 167

Bulb replacement ....................... 168Halogen headlights .................. 168Front turn signal lights ............. 170Tail lights ................................. 172Side turn signal lights .............. 175Number plate light ................... 175Interior lights ............................ 176Instrument panel illumination ... 176

Electrical system ........................ 177Fuses ....................................... 177

Engine compartment fuse box . 178Instrument panel fuse box ....... 180

Vehicle tools .............................. 182Tools ........................................ 182

Wheels and tyres ....................... 183Winter tyres ............................. 183Tyre designations .................... 183Tyre pressure .......................... 184Tyre pressure monitoringsystem .................................... 185

Tread depth ............................. 188Changing tyre and wheel size . 189Wheel covers ........................... 189Tyre chains .............................. 189Tyre repair kit .......................... 190Wheel changing ....................... 194Spare wheel ............................ 196

Jump starting ............................. 201Towing ....................................... 202

Towing the vehicle ................... 202Towing another vehicle ........... 204

Appearance care ....................... 205Exterior care ............................ 205Interior care ............................. 207

General InformationAccessories and vehiclemodificationsWe recommend the use of genuineparts and accessories and factoryapproved parts specific for yourvehicle type. We cannot assess orguarantee reliability of other products- even if they have a regulatory orotherwise granted approval.Do not make any modifications to theelectrical system, e.g. changes ofelectronic control units (chip tuning).

Caution

When transporting the vehicle ona train or on a recovery vehicle, themud flaps might be damaged.

Vehicle care 161

Vehicle storageStorage for a long period of timeIf the vehicle is to be stored for severalmonths:● Wash and wax the vehicle.● Have the wax in the engine

compartment and underbodychecked.

● Clean and preserve the rubberseals.

● Fill up fuel tank completely.● Change the engine oil.● Drain the washer fluid reservoir.● Check the coolant antifreeze and

corrosion protection.● Adjust tyre pressure to the value

specified for full load.● Park the vehicle in a dry, well

ventilated place. Engage first orreverse gear. Prevent the vehiclefrom rolling.

● Do not apply the parking brake.

● Open the bonnet, close all doorsand lock the vehicle.

● Disconnect the clamp from thenegative terminal of the vehiclebattery. Beware that all systemsare not functional, e.g. anti-theftalarm system.

Putting back into operationWhen the vehicle is to be put back intooperation:● Connect the clamp to the

negative terminal of the vehiclebattery. Activate the electronicsof the power windows.

● Check tyre pressure.● Fill up the washer fluid reservoir.● Check the engine oil level.● Check the coolant level.● Fit the number plate if necessary.

End-of-life vehicle recoveryInformation on end-of-life vehiclerecovery centres and the recycling ofend-of-life vehicles is available on ourwebsite. Only entrust this work to anauthorised recycling centre.

Gas vehicles must be recycled by aservice centre authorised for gasvehicles.

162 Vehicle care

Vehicle checksPerforming work

9 Warning

Only perform engine compartmentchecks when the ignition is off.The cooling fan may startoperating even if the ignition is off.

9 Danger

The ignition system usesextremely high voltage. Do nottouch.

BonnetOpening

Pull the release lever and return it toits original position.

Push the safety catch upwards andopen the bonnet.

Secure the bonnet support.

Vehicle care 163

If the bonnet is opened during anAutostop, the engine will be restartedautomatically for safety reasons.

ClosingBefore closing the bonnet, press thesupport into the holder.Lower the bonnet and allow it to fallinto the latch from a low height(20-25 cm). Check that the bonnet isengaged.

Caution

Do not press the bonnet into thelatch, to avoid dents.

Engine oilCheck the engine oil level manuallyon a regular basis to prevent damageto the engine. Ensure that the correctspecification of oil is used.Recommended fluids and lubricants3 210.The maximum engine oilconsumption is 0.6 l per 1000 km.

Check with the vehicle on a levelsurface. The engine must be atoperating temperature and switchedoff for at least five minutes.Pull out the dipstick, wipe it clean,insert it to the stop on the handle, pullout and read the engine oil level.

Caution

It is the owner's responsibility tomaintain the proper level of anappropriate quality oil in theengine.

Insert dipstick to the stop on thehandle and make half a turn.

When the engine oil level hasdropped to the MIN mark, top upengine oil.

We recommend the use of the samegrade of engine oil that was used atlast change.The engine oil level must not exceedthe MAX mark on the dipstick.

Caution

Overfilled engine oil must bedrained or suctioned out.

Capacities 3 222.Fit the cap on straight and tighten it.

164 Vehicle care

Engine coolantThe coolant provides freezeprotection down to approx. -28 °C. Innorthern countries with very lowtemperatures the factory filled coolantprovides frost protection down toapprox. -37 °C.

Caution

Only use approved antifreeze.

Coolant level

Caution

Too low a coolant level can causeengine damage.

If the cooling system is cold, thecoolant level should be above thefilling line mark. Top up if the level islow.

9 Warning

Allow the engine to cool beforeopening the cap. Carefully openthe cap, relieving the pressureslowly.

To top up use a 1:1 mixture ofreleased coolant concentrate mixedwith clean tap water. If no coolantconcentrate is available, use cleantap water. Install the cap tightly. Have

the coolant concentration checkedand have the cause of the coolantloss remedied by a workshop.

Washer fluid

Fill with clean water mixed with asuitable quantity of approvedwindscreen washer fluid whichcontains antifreeze.

Caution

Only washer fluid with a sufficientantifreeze concentration providesprotection at low temperatures ora sudden drop in temperature.

Vehicle care 165

BrakesIn the event of minimum thickness ofthe brake lining, a squealing noisesounds during braking.Continued driving is possible buthave the brake lining replaced assoon as possible.Once new brake linings are installed,do not brake unnecessarily hard forthe first few journeys.

Brake fluid

9 Warning

Brake fluid is poisonous andcorrosive. Avoid contact with eyes,skin, fabrics and painted surfaces.

The brake fluid level must be betweenthe MIN and MAX marks.If fluid level is below MIN seek theassistance of a workshop.Brake and clutch fluid 3 210.

Vehicle batteryThe vehicle battery is maintenance-free provided that the driving profileallows sufficient charging of thebattery. Short-distance-driving andfrequent engine starts can dischargethe vehicle battery. Avoid the use ofunnecessary electrical consumers.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.Laying up the vehicle for more thanfour weeks can lead to vehicle batterydischarge. Disconnect the clamp fromthe negative terminal of the vehiclebattery.Ensure the ignition is switched offbefore connecting or disconnectingthe vehicle battery.The anti-theft alarm siren must bedeactivated as follows: Switch theignition on then off, disconnect thevehicle's battery within 15 seconds.Battery discharge protection 3 112.

166 Vehicle care

Replacing the vehicle batteryNoticeAny deviation from the instructionsgiven in this section may lead totemporary deactivation of the stop-start system.

When the vehicle battery is beingreplaced, please ensure that thereare no open ventilation holes in thevicinity of the positive terminal. If aventilation hole is open in this area, itmust be closed off with a dummy cap,and the ventilation in the vicinity of thenegative terminal must be opened.Only use batteries that allow the fusebox to be mounted above the vehiclebattery.In vehicles with an AGM (AbsorptiveGlass Mat) battery, make sure tohave the battery replaced withanother AGM battery.

An AGM battery can be identified bythe label on the battery. Werecommend the use of an originalVauxhall battery.NoticeUsing an AGM vehicle batterydifferent from the original Vauxhallvehicle battery may result in a lowerperformance.

We recommend that you have thevehicle battery replaced by aworkshop.Stop-start system 3 126.

Charging the vehicle battery

9 Warning

On vehicles with stop-startsystem, ensure that the chargingpotential does not exceed 14.6volts when using a batterycharger. Otherwise the batterymight be damaged.

Jump starting 3 201.

Warning label

Vehicle care 167

Meaning of symbols:● No sparks, naked flames or

smoking.● Always shield eyes. Explosive

gases can cause blindness orinjury.

● Keep the vehicle battery out ofthe reach of children.

● The vehicle battery containssulfuric acid which could causeblindness or serious burninjuries.

● See the Owner's manual forfurther information.

● Explosive gas may be present inthe vicinity of the battery.

Wiper blade replacement

Lift the wiper arm until it stays in theraised position, press button todisengage the wiper blade andremove.Attach the wiper blade slightly angledto the wiper arm and push until itengages.Lower wiper arm carefully.

Wiper blade on the rear window

Lift wiper arm. Disengage wiper bladeas shown in illustration and remove.Attach the wiper blade slightly angledto the wiper arm and push until itengages.Lower wiper arm carefully.

168 Vehicle care

Bulb replacementSwitch off the ignition and switch offthe relevant switch or close the doors.Only hold a new bulb at the base! Donot touch the bulb glass with barehands.Use only the same bulb type forreplacement.Replace headlight bulbs from withinthe engine compartment.

Bulb checkAfter a bulb replacement switch onthe ignition, operate and check thelights.

Halogen headlightsHalogen headlights with separatebulbs for low beam and high beam.

Low beam outer bulb (1).High beam inner bulb (2).

Low beam (1)1. Rotate the cap anticlockwise and

remove it.

2. Press the clip to disengage bulbholder. Withdraw the bulb holderfrom the reflector.

3. Detach the bulb from the bulbholder and replace the bulb.

Vehicle care 169

4. Insert the bulb holder with the clipdownwards and engage into thereflector until it clicks.

5. Install cap.

High beam (2)

1. Rotate the cap anticlockwise andremove it.

2. Press the clip to disengage bulbholder. Withdraw the bulb holderfrom the reflector.

3. Detach the bulb from the bulbholder and replace the bulb.

4. Insert the bulb holder with the clipupwards and engage into thereflector until it clicks.

5. Install cap.

Sidelight/Daytime running lightwith bulbs (3)

1. Rotate bulb socket (3)anticlockwise to disengage.Withdraw the bulb socket from theheadlamp housing.

170 Vehicle care

2. Remove the bulb from the socketby pulling.

3. Replace and insert new bulb intosocket.

4. Insert the bulb socket into theheadlamp housing and turnclockwise.

Sidelight/Daytime running lightwith LEDsSidelights and daytime running lightsconsist of LEDs which cannot bechanged. Consult a workshop in caseof a defective LED.

Front turn signal lights

1. Undo screw and remove cover.

2. Undo screw and remove lightassembly from the bumper.

3. Disengage and remove the bulbsocket by turning anticlockwise.

4. Remove bulb by turninganticlockwise slightly andwithdrawing. Replace the bulb.

Vehicle care 171

5. Insert the bulb socket into theassembly and turn clockwise.

6. Attach light assembly into thebumper and fix with the screw.

7. Insert cover into the bumper andfix with the screw.

Adam Rocks

1. Disengage the small cap with ascrewdriver at the markedposition.

2. Remove the cover by pulling withfingers at the marked positions,see arrows in the illustration.

3. Undo both screws and removelight assembly from the bumper.



172 Vehicle care


7. Attach light assembly into thebumper and fix with both screws.

8. Insert and engage cover into thebumper. Insert small cap.

Tail lightsVersions with subwoofer boxRemove the load compartment floorcover. On right side also remove thetool box to gain access to the cover3 64.Versions with storage boxRemove storage box to gain accessto the cover 3 63.

1. Release the cover on therespective side and remove.

2. Unscrew the plastic securing nutfrom the inside by hand.

3. Carefully withdraw the lightassembly from the recesses andremove.

Vehicle care 173

4. Turn bulb holder anticlockwiseand remove. Replace bulb bywithdrawing:turn signal light 1tail light 2tail light / brake light 3If tail light 2 and tail light/brakelight 3 are LEDs, seek theassistance of a workshop forreplacement.

5. Insert and turn bulb holderclockwise into the tail lightassembly. Ensure the wiresremain in the cable ducts.

Fit light assembly with theretaining pins into the recesses of

the vehicle body and tighten theplastic securing nut from insidethe load compartment. Pull thecircular gasket over the recess inthe lamp housing.Close cover and engage.

Reversing light/rear fog lightReversing light is located on the leftside of the bumper, and the rear foglight is located on the right side of thebumper.The description of bulb replacementis the same for both lights.

1. Undo screw and remove cover.

2. Undo screw and remove lightassembly from the bumper.


174 Vehicle care



6. Replace light assembly in thebumper and fix with the screw.

7. Insert cover into the bumper andfix with the screw.

Adam Rocks

1. Remove the cover by pulling byhand at the marked position, seearrow in the illustration.

2. Undo both screws and removelight assembly from the bumper.


Vehicle care 175



6. Attach light assembly into thebumper and fix with both screws.

7. Insert and engage cover into thebumper.

Side turn signal lightsTo replace bulb, remove lamphousing:

1. Slide lamp to its left side andremove with its right end.

2. Turn bulb holder anticlockwiseand remove from housing.

3. Pull bulb from bulb holder andreplace it.

4. Insert bulb holder and turnclockwise.

5. Insert left end of the lamp, slide tothe left and insert right end.

Number plate light

1. Insert screwdriver in recess of thecover, press to the side andrelease spring.

176 Vehicle care

2. Remove lamp downwards, takingcare not to pull on the cable.

3. Remove bulb holder from lamphousing by turning anticlockwise.

4. Pull bulb from bulb holder andreplace it.

5. Insert bulb holder into lamphousing and turn clockwise.

6. Insert lamp into bumper and allowit to engage.

Interior lightsCourtesy light, reading lightsHave bulbs replaced by a workshop.

Load compartment lightHave bulbs replaced by a workshop.

Dome lightHave bulbs replaced by a workshop.

Ambient lightHave bulbs replaced by a workshop.

Starlight panelHave bulbs replaced by a workshop.

Instrument panelilluminationHave bulbs replaced by a workshop.

Vehicle care 177

Electrical systemFusesData on the replacement fuse mustmatch the data on the defective fuse.There are two fuse boxes in thevehicle:● in the front left of the engine

compartment,● in left-hand drive vehicles behind

the light switch, or, in right-handdrive vehicles, behind theglovebox.

Before replacing a fuse, turn off therespective switch and the ignition.

There are different kinds of fuses inthe vehicle.

Depending on the type of fuse, ablown fuse can be recognized by itsmelted wire. Do not replace the fuseuntil the cause of the fault has beenremedied.Some functions are protected byseveral fuses.Fuses may also be inserted withoutexistence of a function.

Fuse extractorA fuse extractor may be located in thefuse box in the engine compartment.

Place the fuse extractor on thevarious types of fuse from the top, andwithdraw fuse.

178 Vehicle care

Engine compartment fusebox

The fuse box is in the front left of theengine compartment.Disengage the cover and fold itupwards until it stops. Remove thecover vertically upwards.

No. Circuit

1 –

2 Exterior mirror switch

3 Body control module

4 Foldable sunroof/Chassiscontrol module

5 ABS

6 Daytime running light left

7 –

8 Body control module

9 Vehicle battery sensor

10 Headlamp levelling/TPMS/Foldable sunroof

11 Rear wiper

12 Window defog

13 Daytime running light right

14 Mirror defog

15 –

Vehicle care 179

No. Circuit

16 Chassis control module/LPGsystem

17 Interior mirror

18 Engine control module

19 Fuel pump

20 –

21 Injection coil

22 –

23 Injection system

24 Washer system

25 Lighting system


27 –



30 –

31 Left headlamp

No. Circuit

32 Right headlamp


34 Horn

35 Clutch

36 –

180 Vehicle care

No. Circuit

1 ABS pump

2 Front wiper

3 Blower

4 Instrument panel

5 –

6 –

7 Electrical vacuum pump

8 Cooling fan low

9 Cooling fan high

10 Cooling fan/Electrical vacuumpump

11 Starter

After having changed defective fusesclose the fuse box cover and pressuntil it engages.If the fuse box cover is not closedcorrectly, malfunction may occur.

Instrument panel fuse box

The fuse box is located behind acover in the glovebox. Open theglovebox, then open the cover andfold it down.

Vehicle care 181

No. Circuit

1 –

2 –

3 Power windows

4 Voltage transformer

5 Body control module 1








13 –

14 Tailgate

15 Diagnostic connector

16 Data link connection

17 Ignition

No. Circuit

18 Air conditioning system

19 Audio amplifier

20 Parking assist

21 Brake switch

22 Audio system

23 Display

24 –

25 Onstar

26 Instrument panel

27 Seat heating, driver

28 –

29 –

30 Instrument panel

31 Horn

32 Seat heating, passenger

33 Heated steering wheel

34 –

No. Circuit

35 –

36 –

37 Rear wiper

38 Cigarette lighter

39 –

40 –

182 Vehicle care

Vehicle toolsToolsVehicles with tyre repair kit

Some tools and the towing eye arelocated together with the tyre repairkit in a tool box in the loadcompartment below the floor cover.On version with storage box, removebox first 3 63.

On versions with rear carrier systemor liquid gas engine, the tools arelocated together with the towing eyeand tyre repair kit in a suitcase, fixedwith a strap at the left sidewall in theload compartment.

On version with storage box, thesuitcase with the tools, the towing eyeand the tyre repair kit is located in achamber of the box in the loadcompartment 3 63.

Vehicle care 183

On version with subwoofer box, thetools and the towing eye are locatedtogether with the tyre repair kit andthe warning triangle in the box belowthe floor cover. To gain access,remove floor cover: fold rear part tothe front and pull out the cover to therear 3 64.

Vehicles with spare wheel

The jack, the wheel bolt wrench, thetools and two straps for securing adamaged wheel are in the tool boxbelow the load compartment floorcover 3 64.

Wheels and tyres

Tyre condition, wheel conditionDrive over edges slowly and at rightangles if possible. Driving over sharpedges can cause tyre and wheeldamage. Do not trap tyres on the kerbwhen parking.Regularly check the wheels fordamage. Seek the assistance of aworkshop in the event of damage orunusual wear.We recommend not swapping thefront wheels with the rear wheels andvice versa, as this can affect vehiclestability. Always use less worn tyreson the rear axle.

Winter tyresWinter tyres improve driving safety attemperatures below 7 °C and shouldtherefore be fitted on all wheels.All tyre sizes are permitted as wintertyres 3 223.Tyre size 185/60 R 15 is onlypermitted as winter tyre.

In accordance with country-specificregulations, affix the speed sticker inthe driver's field of view.

Tyre designationsE.g. 195/55 R 16 95 H195 : tyre width, mm55 : cross-section ratio (tyre height

to tyre width), %R : belt type: RadialRF : type: RunFlat16 : wheel diameter, inches95 : load index e.g. 95 is equivalent

to 690 kgH : speed code letter

Speed code letter:Q : up to 100 mphS : up to 112 mphT : up to 118 mphH : up to 130 mphV : up to 150 mphW : up to 168 mph

Choose a tyre appropriate for themaximum speed of your vehicle.

184 Vehicle care

The maximum speed is achievable atkerb weight with driver (75 kg) plus125 kg payload. Optional equipmentcould reduce the maximum speed ofthe vehicle.Performance 3 219.

Directional tyresDirectional tyres must be mounted sothat they rotate in the correctdirection. The proper rotationdirection is indicated by a symbol(e.g. an arrow) on the sidewall.

Tyre pressureCheck the pressure of cold tyres atleast every 14 days and before anylong journey. Do not forget the sparewheel.This also applies to vehicles with tyrepressure monitoring system.Unscrew the valve cap.

Tyre pressure 3 223.The tyre pressure information labelon the right door frame indicates theoriginal equipment tyres and thecorrespondent tyre pressures.The tyre pressure data refers to coldtyres. It applies to summer and wintertyres.The ECO tyre pressure serves toachieve the smallest amount of fuelconsumption possible.Incorrect tyre pressures will impairsafety, vehicle handling, comfort andfuel economy and will increase tyrewear.

The tyre pressure tables show allpossible tyre combinations 3 223.Identify the respective tyre.For the tyres approved for yourvehicle, refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.The driver is responsible for correctadjustment of tyre pressure.

9 Warning

If the pressure is too low, this canresult in considerable tyre warm-up and internal damage, leading totread separation and even to tyreblow-out at high speeds.

9 Warning

For specific tyres therecommended tyre pressure asshown in the tyre pressure tablemay exceed the maximum tyrepressure as indicated on the tyre.Never exceed the maximum tyrepressure as indicated on the tyre.

Vehicle care 185

If the tyre pressure must be reducedor increased, switch off ignition. Afteradjusting tyre pressure switch onignition and select the relevant settingon the page Tyre load in the DriverInformation Centre 3 88.

Temperature dependencyThe tyre pressure depends on thetemperature of the tyre. Duringdriving, tyre temperature andpressure increase. Tyre pressurevalues provided on the tyreinformation label and tyre pressurechart are valid for cold tyres, whichmeans at 20 °C.The pressure increases by nearly1.5 psi for a 10 °C temperatureincrease. This must be consideredwhen warm tyres are checked.The tyre pressure value displayed inthe Driver Information Centre showsthe real tyre pressure. A cooled downtyre will show a decreased value,which does not indicate an air leak.

Tyre pressure monitoringsystemThe tyre pressure monitoring systemchecks the pressure of all four tyresonce a minute when vehicle speedexceeds a certain limit.

Caution

Tyre pressure monitoring systemwarns only about low tyre pressurecondition and does not replaceregular tyre maintenance by thedriver.

All wheels must be equipped withpressure sensors and the tyres musthave the prescribed pressure.NoticeIn countries where the tyre pressuremonitoring system is legallyrequired, the use of wheels withoutpressure sensors will invalidate thevehicle type approval.

The current tyre pressures can beshown in the Vehicle InformationMenu in the Driver InformationCentre.

The menu can be selected bypressing the buttons on the turnsignal lever.

Press MENU to select the VehicleInformation MenuX.

186 Vehicle care

Turn the adjuster wheel to select thetyre pressure monitoring system.System status and pressure warningsare displayed by a message with thecorresponding tyre flashing in theDriver Information Centre.The system considers the tyretemperature for the warnings.Temperature dependency 3 184.

A detected low tyre pressurecondition is indicated by the controlindicator w 3 87.If w illuminates, stop as soon aspossible and inflate the tyres asrecommended 3 223.If w flashes for 60-90 seconds thenilluminates continuously, there is afault in the system. Consult aworkshop.After inflating, some driving may berequired to update the tyre pressurevalues in the Driver InformationCentre. During this time w mayilluminate.

If w illuminates at lower temperaturesand extinguishes after some driving,this could be an indicator forapproaching a low tyre pressurecondition. Check tyre pressure.Vehicle messages 3 95.If the tyre pressure must be reducedor increased, switch off ignition.Only mount wheels with pressuresensors, otherwise the tyre pressurewill not be displayed and willuminates continuously.A spare wheel or temporary sparewheel is not equipped with pressuresensors. The tyre pressuremonitoring system is not operationalfor these tyres. Control indicator willuminates. For the further threetyres, the system remainsoperational.The use of commercially-availableliquid tyre repair kits can impair thefunction of the system. Factory-approved repair kits can be used.Operating electronic devices or beingclose to facilities using similar wavefrequencies could disrupt the tyrepressure monitoring system.

Vehicle care 187

Each time the tyres are replaced, tyrepressure monitoring system sensorsmust be dismounted and serviced.For the screwed sensor; replacevalve core and sealing ring. For theclipped sensor; replace completevalve stem.

Vehicle loading statusAdjust tyre pressure to load conditionaccording to the tyre information labelor tyre pressure chart 3 223, andselect the appropriate setting in themenu Tyre Load in the DriverInformation Centre, VehicleInformation Menu 3 88. This setting isthe reference for the tyre pressurewarnings.The Tyre Load menu only appears ifthe vehicle is in a standstill and theparking brake is applied. On vehicleswith automatic transmission theselector lever has to be in P.

Select:● Light for comfort pressure up to

3 people.● Eco for Eco pressure up to

3 people.● Max for full loading.

Tyre pressure sensor matchingprocessEach TPMS sensor has a uniqueidentification code. The identificationcode must be matched to a new tyre/wheel position after rotating the tyresor exchanging the complete wheel setand if one or more TPMS sensorswere replaced. The TPMS sensor

matching process should also beperformed after replacing a spare tyrewith a road tyre containing the TPMSsensor.The malfunction light w and thewarning message or code should gooff at the next ignition cycle. Thesensors are matched to the wheelpositions, using a relearn tool, in thefollowing order: left side front wheel,right side front wheel, right side rearwheel and left side rear wheel. Theturn signal light at the current activeposition is illuminated until sensor ismatched.Consult a workshop for service orpurchase a relearn tool. There aretwo minutes to match the first wheelposition, and five minutes overall tomatch all four wheel positions. If ittakes longer, the matching processstops and must be restarted.The tyre pressure sensor matchingprocess is:1. Apply the parking brake.2. Turn the ignition on.3. On vehicles with manual

transmission automated: Press

188 Vehicle care

and hold brake pedal. Move andhold the selector lever for fiveseconds in position N until P isdisplayed in the DriverInformation Centre. P indicatesthat the sensor matching processcan be started.On vehicles with manualtransmission: select neutral.

4. Use MENU on the turn signallever to select the VehicleInformation Menu in the DriverInformation Centre.

5. Turn the adjuster wheel to scroll tothe tyre pressure menu.

6. Press SET/CLR to begin thesensor matching process. Amessage requesting acceptanceof the process should bedisplayed.

7. Press SET/CLR again to confirmthe selection. The horn soundstwice to indicate that the receiveris in relearn mode.

8. Start with the left side front wheel.9. Place the relearn tool against the

tyre sidewall, near the valve stem.Then press the button to activate

the tyre pressure sensor. A hornchirp confirms that the sensoridentification code has beenmatched to this wheel position.

10. Proceed to the right side frontwheel, and repeat the procedurein Step 9.

11. Proceed to the right side rearwheel, and repeat the procedurein Step 9.

12. Proceed to the left side rearwheel, and repeat the procedurein Step 9. The horn sounds twiceto indicate that the sensoridentification code has beenmatched to the left side rearwheel, and the tyre pressuresensor matching process is nolonger active.

13. Turn off the ignition.14. Set all four tyres to the

recommended air pressure levelas indicated on the tyreinformation label.

15. Ensure the tyre loading status isset according to the selectedpressure 3 88.

Tread depthCheck tread depth at regularintervals.Tyres should be replaced for safetyreasons at a tread depth of 2-3 mm(4 mm for winter tyres).For safety reasons it is recommendedthat the tread depth of the tyres onone axle should not vary by more than2 mm.

The legally permissible minimumtread depth (1.6 mm) has beenreached when the tread has worndown as far as one of the tread wear

Vehicle care 189

indicators (TWI). Their position isindicated by markings on thesidewall.Tyres age, even if they are not used.We recommend tyre replacementevery 6 years.

Changing tyre and wheelsizeIf tyres of a different size than thosefitted at the factory are used, it may benecessary to reprogramme thespeedometer as well as the nominaltyre pressure and to make othervehicle modifications.After converting to a different tyresize, have the label with tyrepressures replaced.

Caution

When converting to wheels with14'', the ground clearance will bereduced. This must be consideredwhen passing over obstacles.

9 Warning

Use of unsuitable tyres or wheelsmay lead to accidents and willinvalidate the vehicle typeapproval.

Wheel coversWheel covers and tyres that arefactory approved for the respectivevehicle and comply with all of therelevant wheel and tyre combinationrequirements must be used.If the wheel covers and tyres used arenot factory approved, the tyres mustnot have a rim protection ridge.Wheel covers must not impair brakecooling.

9 Warning

Use of unsuitable tyres or wheelcovers could lead to suddenpressure loss and therebyaccidents.

Steel wheels: When using lockingwheel bolts, do not attach wheelcovers.

Tyre chains

Tyre chains are only permitted on thefront wheels.Always use fine mesh chains that addno more than 10 mm to the tyre treadand the inboard sides (including chainlock).

9 Warning

Damage may lead to tyre blowout.

190 Vehicle care

Tyre chains are only permitted ontyres of size 175/70 R 14,185/70 R 14, 185/60 R 15,185/65 R 15 and 195/55 R 16.Tyre chains are not permitted on tyresof size 215/45 R 17 and 225/35 R 18.The use of tyre chains is not permittedon the temporary spare wheel.

Tyre repair kitMinor damage to the tyre tread can berepaired with the tyre repair kit.Do not remove foreign bodies fromthe tyres.Tyre damage exceeding 4 mm or thatis at the tyre's sidewall cannot berepaired with the tyre repair kit.

9 Warning

Do not drive faster than 50 mph.Do not use for a lengthy period.Steering and handling may beaffected.

If you have a flat tyre:

Apply the parking brake and engagefirst gear.

The tyre repair kit is in the tool boxunder the floor cover in the loadcompartment.

On versions with rear carrier systemor liquid gas engine, the tyre repair kitis located in a suitcase and fixed witha strap at the left sidewall in the loadcompartment.

Vehicle care 191

On versions with storage box in theload compartment the suitcase withthe tyre repair kit is located in achamber of the box 3 63.

On versions with subwoofer box thetyre repair kit is located in the boxunder the floor cover in the loadcompartment. To use tyre repair kit,firstly remove floor cover: fold rearpart to the front and pull out the coverto the rear 3 64.

1. Take the tyre repair kit from thecompartment.

2. Remove the compressor.

3. Remove the electrical connectioncable and air hose from thestowage compartments on theunderside of the compressor.

4. Screw the compressor air hose tothe connection on the sealantbottle.

5. Fit the sealant bottle into theretainer on the compressor.Set the compressor near the tyrein such a way that the sealantbottle is upright.

192 Vehicle care

6. Unscrew valve cap from defectivetyre.

7. Screw the filler hose to the tyrevalve.

8. The switch on the compressormust be set to J.

9. Connect the compressor plug tothe power outlet or cigarettelighter socket.To avoid discharging the battery,we recommend running theengine.

10. Set the rocker switch on thecompressor to I. The tyre is filledwith sealant.

11. The compressor pressure gaugebriefly indicates up to six barwhilst the sealant bottle isemptying (approx. 30 seconds).Then the pressure starts to drop.

12. All of the sealant is pumped intothe tyre. Then the tyre is inflated.

13. The prescribed tyre pressureshould be obtained within tenminutes. Tyre pressure 3 223.When the correct pressure isobtained, switch off thecompressor.

If the prescribed tyre pressure isnot obtained within ten minutes,remove the tyre repair kit. Movethe vehicle one tyre rotation.Reattach the tyre repair kit andcontinue the filling procedure forten minutes. If the prescribed tyrepressure is still not obtained, thetyre is too badly damaged. Seekthe assistance of a workshop.Drain excess tyre pressure withthe button over the pressureindicator.Do not run the compressor forlonger than ten minutes.

Vehicle care 193

14. Detach the tyre repair kit. Pushcatch on bracket to removesealant bottle from bracket. Screwthe tyre inflation hose to the freeconnection of the sealant bottle.This prevents sealant fromescaping. Stow tyre repair kit inload compartment.

15. Remove any excess sealantusing a cloth.

16. Take the label indicatingmaximum permitted speed fromthe sealant bottle and affix in thedriver's field of view.

17. Continue driving immediately sothat sealant is evenly distributedin the tyre. After driving approx.six miles (but no more than tenminutes), stop and check tyrepressure. Screw compressor airhose directly onto tyre valve andcompressor when doing this.

If tyre pressure is more than1.3 bar, set it to the correct value.Repeat the procedure until thereis no more loss of pressure.If the tyre pressure has fallenbelow 1.3 bar, the vehicle mustnot be used. Seek the assistanceof a workshop.

18. Stow away tyre repair kit in loadcompartment.Reinstall floor cover. Rear floorstorage cover 3 64.

NoticeThe driving characteristics of therepaired tyre are severely affected,therefore have this tyre replaced.

If unusual noise is heard or thecompressor becomes hot, turncompressor off for at least30 minutes.The built-in safety valve opens at apressure of seven bar (102 psi).Note the expiry date of the kit. Afterthis date its sealing capability is nolonger guaranteed. Pay attention tostorage information on sealantbottle.Replace the used sealant bottle.Dispose of the bottle as prescribedby applicable laws.The compressor and sealant can beused from approx. -30 °C.The adapters supplied can be usedto pump up other items e.g.footballs, air mattresses, inflatabledinghies etc. They are located on theunderside of the compressor. Toremove, screw on compressor airhose and withdraw adapter.

194 Vehicle care

Wheel changingMake the following preparations andobserve the following information:● Park the vehicle on a level, firm

and non-skid surface. The frontwheels must be in the straight-ahead position.

● Apply the parking brake andengage first gear or reverse gear.

● Never change more than onewheel at once.

● Use the jack only to changewheels in case of puncture, notfor seasonal winter or summertyre change.

● The jack is maintenance-free.● If the ground on which the vehicle

is standing is soft, a solid board(max. 1 cm thick) should beplaced under the jack.

● Take heavy objects out of thevehicle before jacking up.

● No people or animals may be inthe vehicle when it is jacked-up.

● Never crawl under a jacked-upvehicle.

● Do not start the vehicle when it israised on the jack.

● Before screwing in the wheelbolts, clean them and lightly coatthe taper of each wheel bolt withcommercially available grease.

9 Warning

Do not grease the thread of thewheel bolt.

1. Steel wheels:Pull off the wheel cover.Alloy wheels with bolt capsDisengage wheel bolt caps with ascrewdriver and remove. Toprotect the wheel, place a softcloth between the screwdriverand the alloy wheel.Alloy wheels with centre capTwo versions are available:

1.1. Insert extractor in the openslot of the centre cap and removethe cap from the wheel. Vehicletools 3 182.

1.2. Insert extractor in the hole ofthe centre cap and withdraw the

Vehicle care 195

cap from the wheel. Vehicle tools3 182.

2. Install the wheel wrench ensuringthat it locates securely and looseneach wheel bolt by half a turn.The wheels might be protected bylocking wheel bolts. To loosenthese specific bolts, first attachthe adapter for the locking wheelbolts onto the head of the boltbefore installing the wheelwrench. The adapter is located inthe glovebox.

3. Ensure the jack is correctlypositioned under the relevantvehicle jacking point.

Some versions have sillpanellings with covered vehicle

jacking points: first pull out thecover at the respective jackingpoint before positioning the jack.

4. Set the jack to the necessaryheight. Position it directly belowthe jacking point in a manner thatprevents it from slipping.

196 Vehicle care

Attach jack handle and with thejack correctly aligned rotatehandle until wheel is clear of theground.

5. Unscrew the wheel bolts.6. Change the wheel.7. Screw on the wheel bolts.8. Lower vehicle.9. Install the wheel wrench ensuring

that it locates securely and tighteneach bolt in a crosswisesequence. Tightening torque is110 Nm.

10. Align the valve hole in the wheelcover of the steel wheel with thetyre valve before installing.

Install wheel bolt caps or centrecap on alloy wheel.

11. Stow and secure the replacedwheel, the vehicle tools 3 182 andthe adapter for the locking wheelbolts 3 51.

12. Check the tyre pressure of theinstalled tyre and the wheel bolttorque as soon as possible.

Have the defective tyre renewed orrepaired as soon as possible.

Jacking position for lifting platform

Rear arm position of the liftingplatform, located centrally under therecess of the sill.

Front arm position of the liftingplatform at the underbody.

Spare wheelIf mounting a spare wheel, which isdifferent from the other wheels, thiswheel might be classified as atemporary spare wheel and thecorresponding speed limits apply,even though no label indicates this.Seek the assistance of a workshop tocheck the applicable speed limit.The spare wheel has a steel rim.

Vehicle care 197

Caution

The use of a spare wheel that issmaller than the other wheels or incombination with winter tyrescould affect driveability. Have thedefective tyre replaced as soon aspossible.

The spare wheel is located in a holderbeneath the vehicle floor.1. Open the load compartment floor

3 64.Remove storage box if equipped3 63.

2. Remove the wheel wrench fromthe tool box.

3. Fit the wheel wrench on thehexagon bolt near the tool boxand turn it anticlockwise until aresistance is noticeable.

4. Lift the spare wheel holder slightlyby hand and unhook the catch.

5. Lower the spare wheel holder.

6. Lift the spare wheel holder slightlyby hand and detach the safetycable.

198 Vehicle care

7. Lower holder all the way andremove spare wheel.

8. Change the wheel 3 194.The damaged wheel must besecured in the load compartment,see below.

9. Lift the empty spare wheel holderand insert the safety cable.

10. Lift the spare wheel holder fartherand engage in catch. The openside of the catch must point in thedirection of travel.

11. Close the empty spare wheelholder by turning the hexagon boltclockwise successively using thewheel wrench.

12. Stow wheel wrench and the jackin the tool box in vehicle floor.

13. Close the load compartment floor.

Stowing a damaged wheel in theload compartmentThe spare wheel holder is notdesigned for other tyre sizes than thespare wheel.A damaged wheel wider than thespare wheel must be stowed in theload compartment and secured with astrap. Vehicle tools 3 182.Wheels with tyre size up to195/55 R 161. Remove load compartment cover

and lift up load compartment floor.Stow both behind the raised upbackrests of the rear seats.

2. Untwist wing nut and remove toolbox.

3. Position the damaged wheel tostand upright into the tool boxspare, facing to the front.

Vehicle care 199

4. Remove strap 1 from the tool boxand place the loop end of the strapthrough the right side lashing eye.

5. Place the hook end of the strapthrough the loop and pull it untilthe strap is fastened securely tothe lashing eye.

6. Insert the strap through thespokes of the wheel as shown inthe illustration.

7. Mount the hook to the left sidelashing eye.

8. Tighten the strap and secure itusing the buckle.

9. Position the tool box in the insideof the wheel and secure it withstrap 2 inserted through twospokes of the wheel.

Wheels with tyre size bigger than195/55 R 161. Fold down backrests of the rear

seats 3 62.

2. Remove strap 1 from the tool box.3. Position the damaged wheel with

outer side facing downwards inthe load compartment.

200 Vehicle care

4. Take strap 1 and place the loopend of the strap through the rightside lashing eye.

5. Place the hook end of the strapthrough the loop and pull it untilthe strap is fastened securely tothe lashing eye.

6. Insert the strap through thespokes of the wheel as shown inthe illustration.

7. Mount the hook to the left sidelashing eye.

8. Tighten the strap and secure itusing the buckle.

9 Warning

Storing a jack, a wheel or otherequipment in the loadcompartment could cause injury ifthey are not fixed properly. Duringa sudden stop or a collision, looseequipment could strike someone.Store jack and tools always in therespective storage compartmentsand secure them by fixing.Damaged wheel placed in the loadcompartment must always besecured by the strap.

Temporary spare wheel

Caution

The use of the temporary sparewheel could affect driveability.Have the defective tyre renewedor repaired as soon as possible.

Only mount one temporary sparewheel. Do not drive faster than50 mph. Take curves slowly. Do notuse for a long period of time.

If your vehicle gets a flat tyre on therear while towing another vehicle,mount the temporary spare wheel inthe front and the full size tyre in therear.Tyre chains 3 189.

Spare wheel with directional tyreIf possible, fit directional tyres suchthat they roll in the direction of travel.The rolling direction is indicated by asymbol (e.g. an arrow) on thesidewall.The following applies to tyres fittedopposing the rolling direction:● Driveability may be affected.

Have the defective tyre renewedor repaired as soon as possibleand fit it instead of the sparewheel.

● Drive particularly carefully on wetand snow-covered roadsurfaces.

Vehicle care 201

Jump startingDo not start with a quick charger.A vehicle with a discharged vehiclebattery can be started using jumpleads and the vehicle battery ofanother vehicle.

9 Warning

Be extremely careful when startingwith jump leads. Any deviationfrom the following instructions canlead to injuries or damage causedby battery explosion or damage tothe electrical systems of bothvehicles.

9 Warning

Avoid contact of the battery witheyes, skin, fabrics and paintedsurfaces. The fluid containssulphuric acid which can causeinjuries and damage in the eventof direct contact.

● Never expose the battery tonaked flames or sparks.

● A discharged vehicle battery canalready freeze at a temperatureof 0 °C. Defrost the frozen batterybefore connecting jump leads.

● Wear eye protection andprotective clothing whenhandling a battery.

● Use a booster battery with thesame voltage (12 Volts). Itscapacity (Ah) must not be muchless than that of the dischargedbattery.

● Use jump leads with insulatedterminals and a cross section ofat least 16 mm2 (25 mm2 fordiesel engines).

● Do not disconnect the dischargedvehicle battery from the vehicle.

● Switch off all unnecessaryelectrical consumers.

● Do not lean over the batteryduring jump starting.

● Do not allow the terminals of onelead to touch those of the otherlead.

● The vehicles must not come intocontact with each other duringthe jump starting process.

● Apply the parking brake,transmission in neutral.

● Open the positive terminalprotection caps of both vehiclebatteries.

Lead connection order:1. Connect the red lead to the

positive terminal of the boosterbattery.

2. Connect the other end of the redlead to the positive terminal of thedischarged battery.

202 Vehicle care

3. Connect the black lead to thenegative terminal of the boosterbattery.

4. Connect the other end of the blacklead to a vehicle grounding point,such as the engine block or anengine mounting bolt. Connect asfar away from the dischargedvehicle battery as possible,however at least 60 cm.

Route the leads so that they cannotcatch on rotating parts in the enginecompartment.To start the engine:1. Start the engine of the vehicle

providing the jump.2. After five minutes, start the other

engine. Start attempts should bemade for no longer than15 seconds at an interval ofone minute.

3. Allow both engines to idle forapprox. three minutes with theleads connected.

4. Switch on electrical consumers(e.g. headlights, heated rearwindow) of the vehicle receivingthe jump start.

5. Reverse above sequence exactlywhen removing leads.

TowingTowing the vehicleThe towing eye is stowed with thevehicle tools 3 182.Adam

1. Disengage the cap by pushing atthe marked position.

Vehicle care 203

2. Screw in the towing eye as far asit will go until it stops in ahorizontal position.

3. Attach a tow rope – or better still atow rod – to the towing eye.

Adam Rocks

1. Disengage the small cap with ascrewdriver at the markedposition.

2. Screw in the towing eye as far asit will go until it stops in ahorizontal position.

3. Attach a tow rope – or better still atow rod – to the towing eye.

GeneralThe towing eye must only be used fortowing and not for recovering thevehicle.Switch on ignition to release steeringwheel lock and to permit operation ofbrake lights, horn and windscreenwiper.Transmission in neutral.

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

When the engine is not running,considerably more force is needed tobrake and steer.To prevent the entry of exhaust gasesfrom the towing vehicle, switch on theair recirculation and close thewindows.

204 Vehicle care

Vehicles with manual transmissionautomated: the vehicle must only betowed facing forwards with the frontaxle raised off the ground.Seek the assistance of a workshop.After towing, unscrew the towing eye.Insert cap and engage in the frontbumper.

Towing another vehicleAdam

Insert a screwdriver in the slot at thelower bend of the cap. Disengage thecap by carefully moving thescrewdriver downwards.

The towing eye is stowed with thevehicle tools 3 182.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.The lashing eye at the rearunderneath the vehicle must never beused as a towing eye.Attach a tow rope – or even better atow bar – to the towing eye.The towing eye must only be used fortowing and not for recovering avehicle.

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

After towing, unscrew the towing eye.Insert cap and engage in the bumper.

Adam RocksTowing another vehicle is notpossible.

Vehicle care 205

Appearance careExterior careLocksThe locks are lubricated at the factoryusing a high quality lock cylindergrease. Use a de-icing agent onlywhen absolutely necessary, as thishas a degreasing effect and impairslock function. After using a de-icingagent, have the locks regreased by aworkshop.

WashingAdam without foldable sunroof:The paintwork of your vehicle isexposed to environmental influences.Wash and wax your vehicle regularly.When using automatic vehiclewashes, select a programme thatincludes waxing. Restrictions forfilmed or matt painted body parts ordecor tapes, see "Polishing andwaxing".

Adam with foldable sunroof:The paintwork of your vehicle isexposed to environmental influences,therefore wash your vehicle regularly.When using automatic vehiclewashes, select one with textilebrushes and select a programmewithout wax additives.Restrictions for filmed or matt paintedbody parts or decor tapes, see"Polishing and waxing".When hand washing the vehicle, useclear water and a soft brush, cleaningin grain direction of the textile sunroof.Never use a steam-jet or high-pressure jet cleaner for the sunroof.Wax painted parts of the vehicleregularly, but not the textile of thesunroof.

Caution

After washing or cleaning, thefoldable sunroof must becompletely dried before opening. Ifa wet sunroof remains opened for

a longer time, it would bedamaged by water spotting andmould growth.

All variants:Bird droppings, dead insects, resin,pollen and the like should be cleanedoff immediately, as they containaggressive constituents which cancause paint damage.If using a car wash, comply with thecar wash manufacturer's instructions.The windscreen wiper and rearwindow wiper must be switched off.Remove antenna and externalaccessories such as roof racks etc.If you wash your vehicle by hand,make sure that the insides of thewheel housings are also thoroughlyrinsed out.Clean edges and folds on openeddoors and the bonnet as well as theareas they cover.Clean bright metal mouldings with acleaning solution approved foraluminium to avoid damages.

206 Vehicle care

Caution

Always use a cleaning agent witha pH value of four to nine.Do not use cleaning agents on hotsurfaces.

Have the door hinges of all doorsgreased by a workshop.Do not clean the engine compartmentwith a steam-jet or high-pressure jetcleaner.On vehicles with emblem touchpad:when cleaning with a high-pressurejet cleaner ensure a minimumdistance of 30 cm when workingaround the tailgate to preventunintended unlocking.Thoroughly rinse and leather-off thevehicle. Rinse leather frequently. Useseparate leathers for painted andglass surfaces: remnants of wax onthe windows will impair vision.

Exterior lightsHeadlight and other light covers aremade of plastic. Do not use anyabrasive or caustic agents, do not usean ice scraper, and do not clean themdry.

Polishing and waxingWax painted parts of the vehicleregularly (at the latest when water nolonger beads). Otherwise, thepaintwork will dry out.The foldable sunroof must not bepolished or waxed. When usingautomatic car washes, select aprogramme without wax additives.Polishing is necessary only if the painthas become dull or if solid depositshave become attached to it.Paintwork polish with silicone forms aprotective film, making waxingunnecessary.Unpainted plastic body parts must notbe treated with wax or polishingagents.Matt filmed body parts or decor tapesmust not be polished, to avoidgleaming. Do not use hot wax

programmes in automatic car washesif the vehicle is equipped with theseparts.Matt painted decor parts, e.g. mirrorhousing cover, must not be polished.Otherwise these parts would becomeagleam or the colour would bedissolved.

Windows and windscreen wiperbladesUse a soft lint-free cloth or chamoisleather together with window cleanerand insect remover.When cleaning the rear window frominside, always wipe in parallel to theheating element to prevent damage.For mechanical removal of ice, use asharp-edged ice scraper. Press thescraper firmly against the glass sothat no dirt can get under it andscratch the glass.Clean smearing wiper blades with asoft cloth and window cleaner.

Vehicle care 207

Glass panelNever clean with solvents or abrasiveagents, fuels, aggressive media(e.g. paint cleaner, acetone-containing solutions etc.), acidic orhighly alkaline media or abrasivepads. Do not apply wax or polishingagents to the glass panel.

Wheels and tyresDo not use high-pressure jetcleaners.Clean rims with a pH-neutral wheelcleaner.Rims are painted and can be treatedwith the same agents as the body.

Paintwork damageRectify minor paintwork damage witha touch-up pen before rust forms.Have more extensive damage or rustareas repaired by a workshop.

UnderbodySome areas of the vehicle underbodyhave a PVC undercoating while othercritical areas have a durableprotective wax coating.

After the underbody is washed, checkthe underbody and have it waxed ifnecessary.Bitumen/rubber materials coulddamage the PVC coating. Haveunderbody work carried out by aworkshop.Before and after winter, wash theunderbody and have the protectivewax coating checked.

Liquid gas system

9 Danger

Liquid gas is heavier than air andcan collect in sink points.Take care when performing workat the underbody in a pit.

For painting work and when using adrying booth at a temperature above60 °C, the liquid gas tank must beremoved.Do not make any modifications to theliquid gas system.

Rear carrier systemClean the rear carrier system with asteam-jet or high-pressure jet cleanerat least once a year.Operate the rear carrier systemperiodically if not in regular use, inparticular during winter.

Interior careInterior and upholsteryOnly clean the vehicle interior,including the instrument panel fasciaand panelling, with a dry cloth orinterior cleaner.Clean the leather upholstery withclear water and a soft cloth. In case ofheavy soiling, use leather care.The instrument cluster and thedisplays should only be cleaned usinga soft damp cloth. If necessary use aweak soap solution.Clean fabric upholstery with avacuum cleaner and brush. Removestains with an upholstery cleaner.

208 Vehicle care

Clothing fabrics may not becolourfast. This could cause visiblediscolourations, especially on light-coloured upholstery. Removablestains and discolourations should becleaned as soon as possible.Clean seat belts with lukewarm wateror interior cleaner.

Caution

Close Velcro fasteners as openVelcro fasteners on clothing coulddamage seat upholstery.The same applies to clothing withsharp-edged objects, like zips orbelts or studded jeans.

Plastic and rubber partsPlastic and rubber parts can becleaned with the same cleaner asused to clean the body. Use interiorcleaner if necessary. Do not use anyother agent. Avoid solvents and petrolin particular. Do not use high-pressure jet cleaners.

Service and maintenance 209

Service andmaintenance

General information ................... 209Service information .................. 209

Recommended fluids, lubricantsand parts .................................... 210

Recommended fluids andlubricants ................................ 210

General informationService informationIn order to ensure economical andsafe vehicle operation and tomaintain the value of your vehicle, itis of vital importance that allmaintenance work is carried out at theproper intervals as specified.The detailed, up-to-date serviceschedule for your vehicle is availableat the workshop.Service display 3 80.

European service intervalsMaintenance of your vehicle isrequired every 20,000 miles or after1 year, whichever occurs first, unlessotherwise indicated in the servicedisplay.A shorter service interval can be validfor severe driving behaviour, e.g. fortaxis and police vehicles.The European service intervals arevalid for the following countries:

Andorra, Austria, Belgium, Bosnia-Herzegovina, Bulgaria, Croatia,Cyprus, Czech Republic, Denmark,Estonia, Finland, France, Germany,Greece, Greenland, Hungary,Iceland, Ireland, Italy, Latvia,Liechtenstein, Lithuania,Luxembourg, Macedonia, Malta,Monaco, Montenegro, Netherlands,Norway, Poland, Portugal, Romania,San Marino, Serbia, Slovakia,Slovenia, Spain, Sweden,Switzerland, United Kingdom.Service display 3 80.

International service intervalsMaintenance of your vehicle isrequired every 10,000 miles or after1 year, whichever occurs first, unlessotherwise indicated in the servicedisplay.The international service intervals arevalid for the countries which are notlisted in the European serviceintervals.Service display 3 80.

210 Service and maintenance

ConfirmationsConfirmation of service is recorded inthe Service and Warranty Booklet.The date and mileage is completedwith the stamp and signature of theservicing workshop.Make sure that the Service andWarranty Booklet is completedcorrectly as continuous proof ofservice is essential if any warranty orgoodwill claims are to be met, and isalso a benefit when selling thevehicle.

Service interval with remainingengine oil life durationThe service interval is based onseveral parameters depending onusage.The service display lets you knowwhen to change the engine oil.Service display 3 80.

Recommended fluids,lubricants and partsRecommended fluids andlubricantsOnly use products that meet therecommended specifications.

9 Warning

Operating materials arehazardous and could bepoisonous. Handle with care. Payattention to information given onthe containers.

Engine oilEngine oil is identified by its qualityand its viscosity. Quality is moreimportant than viscosity whenselecting which engine oil to use. Theoil quality ensures e.g. enginecleanliness, wear protection and oilaging control, whereas viscositygrade gives information on the oil'sthickness over a temperature range.

Dexos is the newest engine oil qualitythat provides optimum protection forpetrol and diesel engines. If it isunavailable, engine oils of other listedqualities have to be used.Recommendations for petrol enginesare also valid for Compressed NaturalGas (CNG), Liquified Petroleum Gas(LPG) and Ethanol (E85) fuelledengines.Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 214.

Topping up engine oilEngine oils of different manufacturersand brands can be mixed as long asthey comply with the required engineoil quality and viscosity.Use of engine oil with onlyACEA A1/B1 or only A5/B5 quality isprohibited, since it can cause long-term engine damage under certainoperating conditions.Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 214.

Service and maintenance 211

Additional engine oil additivesThe use of additional engine oiladditives could cause damage andinvalidate the warranty.

Engine oil viscosity gradesThe SAE viscosity grade givesinformation of the thickness of the oil.Multigrade oil is indicated by twofigures, e.g. SAE 5W-30. The firstfigure, followed by a W, indicates thelow temperature viscosity and thesecond figure the high temperatureviscosity.Select the appropriate viscosity gradedepending on the minimum ambienttemperature 3 214.All of the recommended viscositygrades are suitable for high ambienttemperatures.

Coolant and antifreezeUse only silicate-free long life coolant(LLC) antifreeze. Consult aworkshop.The system is factory filled withcoolant designed for excellentcorrosion protection and frostprotection down to approx. -28 °C. In

northern countries with very lowtemperatures the factory filled coolantprovides frost protection down toapprox. -37 °C. This concentrationshould be maintained all year round.The use of additional coolantadditives that intend to give additionalcorrosion protection or seal againstminor leaks can cause functionproblems. Liability for consequencesresulting from the use of additionalcoolant additives will be rejected.

Brake and clutch fluidOver time, brake fluid absorbsmoisture which will reduce brakingeffectiveness. The brake fluid shouldtherefore be replaced at the specifiedinterval.

212 Technical data

Technical data

Vehicle identification .................. 212Vehicle Identification Number .. 212Identification plate ................... 213Engine identification ................ 213

Vehicle data ............................... 214Recommended fluids andlubricants ................................ 214

Engine data ............................. 217Performance ............................ 219Vehicle weight ......................... 220Vehicle dimensions ................. 221Capacities ................................ 222Tyre pressures ........................ 223

Vehicle identificationVehicle IdentificationNumber

The Vehicle Identification Number isstamped on the identification plateand on the floor pan, under the floorcovering, visible under a cover.

The Vehicle Identification Numbermay be embossed on the instrumentpanel visible through the windscreen,or in the engine compartment on theright body panel.

Technical data 213

Identification plate

The identification plate is located onthe left or right front door frame.

Information on identification label:1 : manufacturer2 : type approval number3 : Vehicle Identification Number4 : permissible gross vehicle weight

rating in kg5 : permissible gross train weight

in kg6 : maximum permissible front axle

load in kg7 : maximum permissible rear axle

load in kg8 : vehicle-specific or country-

specific data

The combined total of front and rearaxle loads must not exceed thepermissible gross vehicle weight. Forexample, if the front axle is bearing itsmaximum permissible load, the rearaxle can only bear a load that is equalto the gross vehicle weight minus thefront axle load.The technical data is determined inaccordance with EuropeanCommunity standards. We reservethe right to make modifications.Specifications in the vehicledocuments always have priority overthose given in this manual.

Engine identificationThe technical data tables use theengine identifier code. The enginedata table additionally shows theengineering code. Engine data3 217.To identify the respective engine,refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.The Certificate of Conformity showsthe engine identifier code, othernational publications may show theengineering code. Check pistondisplacement and engine power toidentify the respective engine.

214 Technical data

Vehicle dataRecommended fluids and lubricantsEuropean service schedule

Required engine oil qualityAll European countries with European service interval 3 209

Engine oil quality Petrol engines(including CNG, LPG, E85)

dexos 1 –

dexos 2 ✔

In case dexos quality is unavailable you may use max. one litre engine oil quality ACEA C3 for topping up once betweeneach oil change.

Engine oil viscosity gradesAll European countries with European service interval 3 209

Ambient temperature Petrol and diesel engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

Technical data 215

International service schedule

Required engine oil qualityAll countries with international service interval 3 209


dexos 1 ✔

dexos 2 ✔

In case dexos quality is unavailable you may use the oil qualities listed below:

All countries with international service interval 3 209


GM-LL-A-025 ✔

GM-LL-B-025 –



ACEA A3/B3 ✔

ACEA A3/B4 ✔

216 Technical data


ACEA C3 ✔

API SM ✔

API SN resource conserving ✔

Engine oil viscosity gradesAll countries with international service interval 3 209

Ambient temperature Petrol and diesel engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

down to -20 °C SAE 10W-301) or SAE 10W-401)

1) Permitted, but usage of SAE 5W-30 or SAE 5W-40 with dexos quality is recommended.

Technical data 217

Engine dataEngine identifier code B10XFL B10XFT B12XEL B14XELSales designation 1.0 1.0 1.2 1.4Engineering code B10XFT B10XFT B12XER B14XER

Piston displacement [cm3] 999 999 1229 1398

Engine power [kW] 66 85 51 64

at rpm 3700-6000 5000-6000 5600 6000

Torque [Nm] 170 170 115 130

at rpm 1800-3700 1800-4500 4000 4000

Fuel type Petrol Petrol Petrol Petrol

Octane rating RON2)

recommended 95 95 95 95

possible 98 98 98 98

possible 91 91 91 91

Additional fuel type – – – –

2) A country specific label at the fuel filler flap can supersede the engine specific requirement.

218 Technical data

Engine identifier code B14XEL B14XER B14NEHSales designation 1.4 LPG 1.4 Adam SEngineering code B14XER B14XER B14NET

Piston displacement [cm3] 1398 1398 1364

Engine power [kW] 64 74 110

at rpm 6000 6000 5000

Torque [Nm] 1303) 130 220

at rpm 4000 4000 3000-4500

Fuel type Liquid gas/Petrol Petrol Petrol

Octane rating RON2)

recommended 95 95 98

possible 98 98 95

possible 91 91 –

Additional fuel type Liquid gas (LPG) – –

2) A country specific label at the fuel filler flap can supersede the engine specific requirement.3) LPG operation: 124.

Technical data 219

Performance

Engine B10XFL B10XFT B12XEL B14XELB14XELLPG B14XER B14NEH

Maximum speed [mph]

Manual transmission 112 122 103 109 109 115 130

Manual transmission automated – – – 110 – – –

220 Technical data

Vehicle weightKerb weight, basic model without any optional equipment

Engine Manual transmission Manual transmission automated

without/with air conditioning[kg]

B10XFL 1141/1156 –

B10XFT 1141/1156 –

B12XEL 1086/1101 –

B14XEL 1120/1135 1120/1135

B14XEL LPG 1163/1178 –

B14XER 1120/1135 –

B14NEH 1163/1178 –

Optional equipment and accessories increase the kerb weight.Loading information 3 67.

Technical data 221

Vehicle dimensionsLength [mm] 3747

Width without exterior mirrors [mm] 1720

Width with two exterior mirrors [mm] 1966

Height (without antenna) [mm] 1475-15084)

Length of load compartment floor [mm] 462

Length of load compartment with folded rear seats [mm] 1041

Load compartment width [mm] 954

Load compartment height [mm] 874

Wheelbase [mm] 2311

Turning circle diameter [m] 10.17-11.064)

4) Depending on equipment.

222 Technical data

CapacitiesEngine oil

Engine B10XFL B10XFT B12XEL B14XEL B14XELLPG

B14XER B14NEH

including Filter [l] 4.0 4.0 4.0 4.0 4.0 4.0 4.0

between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 1.0 1.0

Fuel tank

Engine B10XFL B10XFT B12XEL B14XEL B14XELLPG

B14XER B14NEH

Petrol, refilling quantity [l] 35 35 35 35 35 35 35

LPG, refilling quantity [l] – – – – 35 – –

Technical data 223

Tyre pressuresComfort with up to 3people ECO with up to 3 people

With full load

Engine Tyres front rear front rear front rear[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

B10XFL,B12XEL,B14XEL,B14XEL LPG,B14XER

175/70 R14,185/70 R14,185/60 R15,185/65 R15,195/55 R16,215/45 R17,225/35 R18

220/2.2 (32) 200/2.0 (29) 290/2.9 (42) 270/2.7 (39) 260/2.6 (38) 320/3.2 (46)

B10XFT 185/60 R15,195/55 R16,215/45 R17,225/35 R18

220/2.2 (32) 200/2.0 (29) 290/2.9 (42) 270/2.7 (39) 260/2.6 (38) 320/3.2 (46)

B14NEH 195/55 R16,215/45 R17,225/35 R18

220/2.2 (32) 200/2.0 (29) 290/2.9 (42) 270/2.7 (39) 260/2.6 (38) 320/3.2 (46)

224 Technical data

Comfort with up to 3people ECO with up to 3 people

With full load

Engine Tyres front rear front rear front rear[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

All Temporary spare wheel115/70 R16

420/4.2 (61) 420/4.2 (61) – – 420/4.2 (61) 420/4.2 (61)

Customer information 225

Customerinformation

Customer information ................ 225Declaration of conformity ......... 225Collision damage repair ........... 227Software acknowledgement .... 227

Vehicle data recording and pri‐vacy ........................................... 229

Event data recorders ............... 229Radio Frequency Identification(RFID) ..................................... 230

Customer informationDeclaration of conformityTransmission systemsThis vehicle has systems thattransmit and/or receive radio wavessubject to Directive 1999/5/EC.These systems are in compliancewith the essential requirements andother relevant provisions of Directive1999/5/EC. Copies of the originalDeclarations of Conformity can beobtained on our website.

226 Customer information

Jack


Translation of the original declarationof conformityDeclaration of conformity accordingto EC Directive 2006/42/ECWe declare that the product:Product designation: JackType/GM part number: 13331922is in compliance with the provisions ofDirective 2006/42/EC.Applied technical standards:GMN9737 : JackingGM 14337 : Standard

Equipment Jack –Hardware Tests

GMN5127 : Vehicle Integrity –Hoisting andService StationJacking

GMW15005 : StandardEquipment Jackand Spare Tyre,Vehicle Test

ISO TS 16949 : Qualitymanagementsystems

The signatory is authorised tocompile the technical documentation.Rüsselsheim, 31st January 2014signed byHans-Peter MetzgerEngineering Group Manager Chassis& StructureAdam Opel AGD-65423 Rüsselsheim

Collision damage repairPaint thicknessDue to production techniques, thethickness of the paint can varybetween 50 and 400 µm.Therefore, different paint thickness isno indicator for a collision damagerepair.

Software acknowledgementCertain OnStar components includelibcurl and unzip software and otherthird party software. Below are thenotices and licenses associated withlibcurl and unzip and for other thirdparty software please see http://www.lg.com/global/support/opensource/index.

libcurlCopyright and permission noticeCopyright (c) 1996 - 2010, DanielStenberg, <[email protected]>.All rights reserved.Permission to use, copy, modify, anddistribute this software for anypurpose with or without fee is herebygranted, provided that the abovecopyright notice and this permissionnotice appear in all copies.The software is provided "as is",without warranty of any kind, expressor implied, including but not limited tothe warranties of merchantability,fitness for a particular purpose andnoninfringement of third party rights.In no event shall the authors or


copyright holders be liable for anyclaim, damages or other liability,whether in an action of contract, tortor otherwise, arising from, out of or inconnection with the software or theuse or other dealings in the software.Except as contained in this notice, thename of a copyright holder shall notbe used in advertising or otherwise topromote the sale, use or otherdealings in this Software without priorwritten authorization of the copyrightholder.

unzipThis is version 2005-Feb-10 of theInfo-ZIP copyright and license. Thedefinitive version of this documentshould be available at ftp://ftp.info-zip.org/pub/infozip/license.htmlindefinitely.Copyright (c) 1990-2005 Info-ZIP. Allrights reserved.For the purposes of this copyright andlicense, “Info-ZIP” is defined as thefollowing set of individuals:Mark Adler, John Bush, Karl Davis,Harald Denker, Jean-Michel Dubois,Jean-loup Gailly, Hunter Goatley, Ed

Gordon, Ian Gorman, Chris Herborth,Dirk Haase, Greg Hartwig, RobertHeath, Jonathan Hudson, PaulKienitz, David Kirschbaum, JohnnyLee, Onno van der Linden, IgorMandrichenko, Steve P. Miller, SergioMonesi, Keith Owens, GeorgePetrov, Greg Roelofs, Kai UweRommel, Steve Salisbury, DaveSmith, Steven M. Schweda, ChristianSpieler, Cosmin Truta, AntoineVerheijen, Paul von Behren, RichWales, Mike White.This software is provided “as is,”without warranty of any kind, expressor implied. In no event shall Info-ZIPor its contributors be held liable forany direct, indirect, incidental, specialor consequential damages arising outof the use of or inability to use thissoftware.Permission is granted to anyone touse this software for any purpose,including commercial applications,and to alter it and redistribute it freely,subject to the following restrictions:

1. Redistributions of source codemust retain the above copyrightnotice, definition, disclaimer, andthis list of conditions.

2. Redistributions in binary form(compiled executables) mustreproduce the above copyrightnotice, definition, disclaimer, andthis list of conditions indocumentation and/or othermaterials provided with thedistribution. The sole exception tothis condition is redistribution of astandard UnZipSFX binary(including SFXWiz) as part of aself-extracting archive; that ispermitted without inclusion of thislicense, as long as the normalSFX banner has not beenremoved from the binary ordisabled.

3. Altered versions--including, butnot limited to, ports to newoperating systems, existing portswith new graphical interfaces, anddynamic, shared, or static libraryversions--must be plainly markedas such and must not bemisrepresented as being the


original source. Such alteredversions also must not bemisrepresented as being Info-ZIPreleases--including, but notlimited to, labeling of the alteredversions with the names “Info-ZIP” (or any variation thereof,including, but not limited to,different capitalizations), “PocketUnZip,” “WiZ” or “MacZip” withoutthe explicit permission of Info-ZIP.Such altered versions are furtherprohibited from misrepresentativeuse of the Zip-Bugs or Info-ZIP e-mail addresses or of the Info-ZIPURL(s).

4. Info-ZIP retains the right to usethe names “Info-ZIP,” “Zip,”“UnZip,” “UnZipSFX,” “WiZ,”“Pocket UnZip,” “Pocket Zip,” and“MacZip” for its own source andbinary releases.

Vehicle data recordingand privacyEvent data recordersData storage modules in thevehicleA large number of electroniccomponents of your vehicle containdata storage modules temporarily orpermanently storing technical dataabout the condition of the vehicle,events and errors. In general, thistechnical information documents thecondition of parts, modules, systemsor the environment:● operating conditions of system

components (e.g. filling levels)● status messages of the vehicle

and its single components (e.g.number of wheel revolutions /rotational speed, deceleration,lateral acceleration)

● dysfunctions and defects inimportant system components

● vehicle reactions in particulardriving situations (e.g. inflation ofan airbag, activation of thestability regulation system)

● environmental conditions (e.g.temperature)

These data are exclusively technicaland help identifying and correctingerrors as well as optimising vehiclefunctions.Motion profiles indicating travelledroutes cannot be created with thesedata.If services are used (e.g. repairworks, service processes, warrantycases, quality assurance),employees of the service network(manufacturer included) are able toread out this technical informationfrom the event and error data storagemodules applying special diagnosticdevices. If required, you will receivefurther information at theseworkshops. After an error has beencorrected, the data are deleted fromthe error storage module or they areconstantly overwritten.


When using the vehicle, situationsmay occur in which these technicaldata related to other information(accident report, damages on thevehicle, witness statements etc.) maybe associated with a specific person -possibly, with the assistance of anexpert.Additional functions contractuallyagreed upon with the client (e.g.vehicle location in emergency cases)allow the transmission of particularvehicle data from the vehicle.

Radio FrequencyIdentification (RFID)RFID technology is used in somevehicles for functions such as tyrepressure monitoring and ignitionsystem security. It is also used inconnection with conveniences suchas radio remote controls for doorlocking/unlocking and starting, and in-vehicle transmitters for garage dooropeners. RFID technology inVauxhall vehicles does not use orrecord personal information or linkwith any other Vauxhall systemcontaining personal information.

232

Index AAccessories and vehicle

modifications .......................... 160Adjustable air vents ................... 121Airbag and belt tensioners ........... 84Airbag deactivation ................ 44, 84Airbag label................................... 39Airbag system .............................. 39Air conditioning regular

operation ................................ 122Air conditioning system .............. 114Air intake .................................... 121Air vents...................................... 121Antilock brake system ................ 134Antilock brake system (ABS) ....... 86Anti-theft alarm system ................ 25Anti-theft locking system .............. 25Appearance care........................ 205Ashtrays ....................................... 77Automatic anti-dazzle .................. 28Automatic light control ............... 106Automatic locking ........................ 23Autostop..................................... 126

BBattery discharge protection ...... 112Battery voltage ............................. 97Belts.............................................. 37Bicycle rack.................................. 53Bonnet ....................................... 162

Brake and clutch fluid................. 210Brake and clutch system ............. 85Brake assist ............................... 135Brake fluid .................................. 165Brakes ............................... 134, 165Breakdown.................................. 202Bulb replacement ....................... 168

CCapacities .................................. 222Car Pass ...................................... 20Catalytic converter ..................... 129Central locking system ................ 22Changing tyre and wheel size . . . 189Charging system .......................... 84Child restraint installation

locations ................................... 47Child restraints.............................. 45Child restraint systems ................ 45Cigarette lighter ........................... 77City mode................................... 138Climate control ............................. 15Climate control systems............. 113Clock ............................................ 74Code............................................. 95Collision damage repair.............. 227Colour-Info-Display....................... 93Control indicators.......................... 81Control of the vehicle ................. 123Controls........................................ 70

233

Convex shape .............................. 27Coolant and antifreeze............... 210Cruise control ...................... 88, 139Cupholders .................................. 51Curtain airbag system .................. 43

DDanger, Warnings and Cautions . . . 4Daytime running lights ............... 107Declaration of conformity............ 225Door open .................................... 88Doors............................................ 24Driver assistance systems.......... 139Driver Information Centre............. 88Driving hints................................ 123

EElectric adjustment ...................... 27Electrical system......................... 177Electronic climate control system 116Electronic driving programmes . . 133Electronic Stability Control.......... 137Electronic Stability Control and

Traction Control system............ 86Electronic Stability Control off....... 86End-of-life vehicle recovery ....... 161Engine compartment fuse box ... 178Engine coolant ........................... 164Engine coolant temperature

gauge ....................................... 80Engine data ............................... 217

Engine exhaust .......................... 129Engine identification................... 213Engine oil ................... 163, 210, 214Engine oil pressure ...................... 87Entry lighting .............................. 111Event data recorders.................. 229Exit lighting ................................ 111Exterior care .............................. 205Exterior light ................................. 88Exterior lighting .................... 12, 105Exterior mirrors............................. 27

FFault ........................................... 133First aid......................................... 67First aid kit ................................... 67Fixed air vents ........................... 121Flex-Fix system............................ 53Folding mirrors ............................. 27Front airbag system ..................... 42Front seats.................................... 33Front storage................................ 52Front turn signal lights ............... 170Fuel............................................. 153Fuel consumption - CO2-

Emissions ............................... 158Fuel for liquid gas operation....... 153Fuel for petrol engines ............... 153Fuel gauge ................................... 79

Fuel selector ................................ 79Fuses ......................................... 177

GGauges......................................... 78Glass panel .................................. 31Glovebox ..................................... 51Graphic-Info-Display..................... 94

HHalogen headlights .................... 168Hand brake......................... 134, 135Hazard warning flashers ............ 107Headlight flash ........................... 106Headlight range adjustment ...... 107Headlights................................... 105Headlights when driving abroad 107Head restraint adjustment ............. 8Head restraints ............................ 32Heated mirrors ............................. 28Heated rear window ..................... 30Heated steering wheel ................. 70Heating ........................................ 36Heating and ventilation system . 113High beam ........................... 88, 106Hill start assist ........................... 135Horn ....................................... 13, 71

IIdentification plate ..................... 213Ignition switch positions ............. 124

234

Immobiliser ............................ 26, 88Indicators...................................... 78Inductive charging........................ 76Information displays...................... 88Instrument cluster ........................ 78Instrument panel fuse box ......... 180Instrument panel illumination ..... 176Instrument panel illumination

control .................................... 109Instrument panel overview ........... 10Interior care ............................... 207Interior lighting............................ 109Interior lights ...................... 109, 176Interior mirrors.............................. 28Introduction .................................... 3ISOFIX child restraint systems .... 50

JJump starting ............................. 201

KKey, memorised settings.............. 21Keys ............................................. 19Keys, locks................................... 19

LLashing eyes ............................... 66Light switch ................................ 105Load compartment ................ 24, 62Load compartment cover ............. 64

Loading information ..................... 67Low fuel ....................................... 87

MMalfunction indicator light ............ 85Manual anti-dazzle ...................... 28Manual mode ............................. 133Manual transmission .................. 130Manual transmission automated 130Memorised settings...................... 21Midlevel-Display........................... 88Mirror adjustment ........................... 8Misted light covers ..................... 109

NNew vehicle running-in .............. 124Number plate light ..................... 175

OObject detection systems........... 142Odometer ..................................... 78Oil, engine.......................... 210, 214OnStar........................................ 101Operate pedal............................... 85Outside temperature .................... 73Overrun cut-off ........................... 125

PParking ................................ 18, 128Parking assist ............................ 142Parking brake ............................ 135

Parking lights ............................. 108Performance .............................. 219Performing work ........................ 162Pollen filter ................................. 121Power outlets ............................... 76Power steering.............................. 86Power windows ............................ 29Puncture..................................... 194

RRadio Frequency Identification

(RFID)..................................... 230Radio remote control ................... 20Rear carrier system...................... 53Rear floor storage cover .............. 64Rear fog light ............................... 88Rear fog lights ........................... 108Rear storage................................. 63Rear window wiper/washer .......... 73Recommended fluids and

lubricants ........................ 210, 214Refuelling ................................... 155Retained power off..................... 124Reversing lights ......................... 109Ride control systems.................. 136Roof load...................................... 67Roof rack ..................................... 67

SSafety belts................................... 37Seat adjustment ....................... 7, 34

235

Seat belt ........................................ 8Seat belt reminder ....................... 83Seat belts ..................................... 37Seat folding .................................. 35Seat heating................................. 36Seat position ................................ 33Selector lever ............................. 131Service ....................................... 122Service display ............................ 80Service information .................... 209Service vehicle soon .................... 85Side airbag system ...................... 43Side blind spot alert.................... 151Sidelights.................................... 105Side turn signal lights ................ 175Software acknowledgement....... 227Spare wheel ............................... 196Speed limiter............................... 141Speedometer ............................... 78Starting and operating................ 124Starting off ................................... 16Starting the engine ............ 125, 131Steering...................................... 124Steering wheel adjustment ...... 9, 70Steering wheel controls ............... 70Stop-start system........................ 126Storage......................................... 51Storage compartments................. 51Sunroof ........................................ 31

Sun visors .................................... 30Symbols ......................................... 4

TTachometer ................................. 78Tail lights ................................... 172Three-point seat belt .................... 38Tools .......................................... 182Top-tether fastening eyes ............ 50Towing........................................ 202Towing another vehicle ............. 204Towing the vehicle ..................... 202Traction Control system ............. 136Transmission ............................... 16Transmission display ................. 131Tread depth ............................... 188Trip odometer .............................. 78Turn and lane-change signals ... 108Turn signal ................................... 83Tyre chains ................................ 189Tyre designations ...................... 183Tyre pressure ............................ 184Tyre pressure monitoring

system............................... 87, 185Tyre pressures ........................... 223Tyre repair kit ............................. 190

UUltrasonic parking assist ...... 86, 142Upholstery.................................. 207Uplevel-Display............................. 88

Upshift.......................................... 86Using this manual .......................... 3

VVehicle battery ........................... 165Vehicle checks............................ 162Vehicle data................................ 214Vehicle data recording and

privacy..................................... 229Vehicle dimensions .................... 221Vehicle Identification Number .... 212Vehicle jack................................ 182Vehicle messages ....................... 95Vehicle personalisation ............... 98Vehicle security............................ 25Vehicle specific data ...................... 3Vehicle storage........................... 161Vehicle tools............................... 182Vehicle unlocking ........................... 6Vehicle weight ........................... 220Ventilation................................... 113

WWarning chimes ........................... 97Warning lights............................... 78Warning triangle .......................... 66Washer and wiper systems ......... 14Washer fluid ............................... 164Wheel changing ......................... 194Wheel covers ............................. 189Wheels and tyres ....................... 183

236

Windows....................................... 29Windscreen................................... 29Windscreen wiper/washer ........... 71Winter tyres ............................... 183Wiper blade replacement .......... 167

Copyright by General Motors UK Ltd.

The information contained in this publication is effective as of the date indicated below. General Motors UK Ltd. reserves the rightto make changes to the technical specifications, features and design of the vehicles relative to the information contained in thispublication, as well as changes to the publication itself.

Edition: January 2016, General Motors UK Ltd.

Printed on chlorine-free bleached paper.

*KTA-2744/9-VX-EN*

KTA-2744/9-VX-en 01/2016

vauxhall adam owner's manual · press release button, adjust height, engage. head restraints 3...

Documents