vehicle body engineering and safety
TRANSCRIPT
JNTUWORLD
Code No: A107412404 Set No. 1 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., II Mid-Term Examinations, November – 2010 VEHICLE BODY ENGINEERING AND SAFETY
Objective Exam Name: ______________________________ Hall Ticket No.
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.
I Choose the correct alternative: 1. Which of the following car body shapes has the largest internal dimensions? [ ]
a) coupe b) saloon c) convertible d) estate
2. An enclosed two seater body having a fixed roof [ ] a) Couple b) Single c) Saloon d) None
3. The fundamental components fixed near to driver seat are [ ]
a) stereo b) air condition control c) steering, gear and foot control d) none 4. According to the visibility regulations,horizontal and vertical distance to be visible are [ ]
a) 12m,5m b) 10m,8m c) 8m,10m d) None 5. A fuse in an electrical circuit ‘blows’ as the result of a high [ ]
a) Voltage caused by a short circuit b) Current flow caused by a short circuit c) Voltage caused by an open circuit d) Current flow caused by an open circuit
6. In car a temperature indicating instrument is usually provided which indicates the temperature of [ ]
a) Engine piston b) Engine cylinder c) Lubricating oil d) Jacket cooling water 7. Noisy brakes indicate [ ]
a) rift on lining b) drums scored c) loose lining screws d) any of the above 8. To balance a single cylinder engine a counter weight is added to [ ]
a) piston b) connecting rod c) crankshaft d) gudgeon pin 9. The frame provided for supporting the unit of chassis and body, in case of Tata vehicles is[ ]
a) cross member-type frame b) center beam frame c) Y-shaped tube frame d) Self supporting structure
10. The pressure of air in case of heavy duty truck is usually of the order of [ ]
a) 1 to 2 atm b) 2 to 3 atm c) 4 to 7 atm d) Depends of the roads conditions Cont……..2
A
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
JNTUWORLD
Code No: A107412404 :2: Set No. 1
II Fill in the blanks 11. In a vehicle the probable cause for hard steering could be____________ 12. A frame consisting of side and cross members of channel section is normally used on____________ 13. As applied to the specification of a heavy commercial vehicle the abbreviation g.v.w is__________ 14. Most motor cars use a specially constructed body shell onto which the main components are
attached.It is called ____________ type 15. The type of engine used in a heavy commercial vehicle is _____________ 16. When a vehicle turns a corner, the action of the differential causes______________ 17. A collapsible steering column is one which collapses to ____________ 18. Fluid drive is one name for _____________ 19. The factor not considered to oppose the motion of the vehicle is ______________ 20. The part of the vehicle which holds the passengers and the cargo to be transported is known as
____________
-oOo-
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
JNTUWORLD
Code No: A107412404 Set No. 2 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., II Mid-Term Examinations, November – 2010 VEHICLE BODY ENGINEERING AND SAFETY
Objective Exam Name: ______________________________ Hall Ticket No.
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.
I Choose the correct alternative:
1. According to the visibility regulations,horizontal and vertical distance to be visible are [ ] a) 12m,5m b) 10m,8m c) 8m,10m d) None
2. A fuse in an electrical circuit ‘blows’ as the result of a high [ ]
a) Voltage caused by a short circuit b) Current flow caused by a short circuit c) Voltage caused by an open circuit d) Current flow caused by an open circuit
3. In car a temperature indicating instrument is usually provided which indicates the temperature of [ ]
a) Engine piston b) Engine cylinder c) Lubricating oil d) Jacket cooling water 4. Noisy brakes indicate [ ]
a) rift on lining b) drums scored c) loose lining screws d) any of the above 5. To balance a single cylinder engine a counter weight is added to [ ]
a) piston b) connecting rod c) crankshaft d) gudgeon pin 6. The frame provided for supporting the unit of chassis and body, in case of Tata vehicles is[ ]
a) cross member-type frame b) center beam frame c) Y-shaped tube frame d) Self supporting structure
7. The pressure of air in case of heavy duty truck is usually of the order of [ ]
a) 1 to 2 atm b) 2 to 3 atm c) 4 to 7 atm d) Depends of the roads conditions 8. Which of the following car body shapes has the largest internal dimensions? [ ]
a) coupe b) saloon c) convertible d) estate
9. An enclosed two seater body having a fixed roof [ ] a) Couple b) Single c) Saloon d) None
10. The fundamental components fixed near to driver seat are [ ]
a) stereo b) air condition control c) steering, gear and foot control d) none
Cont……..2
A
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
JNTUWORLD
Code No: A107412404 :2: Set No. 2
II Fill in the blanks 11. Most motor cars use a specially constructed body shell onto which the main components are
attached.It is called ____________ type 12. The type of engine used in a heavy commercial vehicle is _____________ 13. When a vehicle turns a corner, the action of the differential causes______________ 14. A collapsible steering column is one which collapses to ____________ 15. Fluid drive is one name for _____________ 16. The factor not considered to oppose the motion of the vehicle is ______________ 17. The part of the vehicle which holds the passengers and the cargo to be transported is known as
____________ 18. In a vehicle the probable cause for hard steering could be____________ 19. A frame consisting of side and cross members of channel section is normally used on____________ 20. As applied to the specification of a heavy commercial vehicle the abbreviation g.v.w is__________ -oOo-
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
JNTUWORLD
Code No: A107412404 Set No. 3 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., II Mid-Term Examinations, November – 2010 VEHICLE BODY ENGINEERING AND SAFETY
Objective Exam Name: ______________________________ Hall Ticket No.
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.
I Choose the correct alternative: 1. In car a temperature indicating instrument is usually provided which indicates the temperature of [ ]
a) Engine piston b) Engine cylinder c) Lubricating oil d) Jacket cooling water 2. Noisy brakes indicate [ ]
a) rift on lining b) drums scored c) loose lining screws d) any of the above 3. To balance a single cylinder engine a counter weight is added to [ ]
a) piston b) connecting rod c) crankshaft d) gudgeon pin 4. The frame provided for supporting the unit of chassis and body, in case of Tata vehicles is[ ]
a) cross member-type frame b) center beam frame c) Y-shaped tube frame d) Self supporting structure
5. The pressure of air in case of heavy duty truck is usually of the order of [ ]
a) 1 to 2 atm b) 2 to 3 atm c) 4 to 7 atm d) Depends of the roads conditions 6. Which of the following car body shapes has the largest internal dimensions? [ ]
a) coupe b) saloon c) convertible d) estate
7. An enclosed two seater body having a fixed roof [ ] a) Couple b) Single c) Saloon d) None
8. The fundamental components fixed near to driver seat are [ ]
a) stereo b) air condition control c) steering, gear and foot control d) none 9. According to the visibility regulations,horizontal and vertical distance to be visible are [ ]
a) 12m,5m b) 10m,8m c) 8m,10m d) None 10. A fuse in an electrical circuit ‘blows’ as the result of a high [ ]
a) Voltage caused by a short circuit b) Current flow caused by a short circuit c) Voltage caused by an open circuit d) Current flow caused by an open circuit
Cont……..2
A
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
JNTUWORLD
Code No: A107412404 :2: Set No. 3
II Fill in the blanks 11. When a vehicle turns a corner, the action of the differential causes______________ 12. A collapsible steering column is one which collapses to ____________ 13. Fluid drive is one name for _____________ 14. The factor not considered to oppose the motion of the vehicle is ______________ 15. The part of the vehicle which holds the passengers and the cargo to be transported is known as
____________ 16. In a vehicle the probable cause for hard steering could be____________ 17. A frame consisting of side and cross members of channel section is normally used on____________ 18. As applied to the specification of a heavy commercial vehicle the abbreviation g.v.w is__________ 19. Most motor cars use a specially constructed body shell onto which the main components are
attached.It is called ____________ type 20. The type of engine used in a heavy commercial vehicle is _____________
-oOo-
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
JNTUWORLD
Code No: A107412404 Set No. 4 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., II Mid-Term Examinations, November – 2010 VEHICLE BODY ENGINEERING AND SAFETY
Objective Exam Name: ______________________________ Hall Ticket No.
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.
I Choose the correct alternative:
1. To balance a single cylinder engine a counter weight is added to [ ] a) piston b) connecting rod c) crankshaft d) gudgeon pin
2. The frame provided for supporting the unit of chassis and body, in case of Tata vehicles is[ ]
a) cross member-type frame b) center beam frame c) Y-shaped tube frame d) Self supporting structure
3. The pressure of air in case of heavy duty truck is usually of the order of [ ]
a) 1 to 2 atm b) 2 to 3 atm c) 4 to 7 atm d) Depends of the roads conditions 4. Which of the following car body shapes has the largest internal dimensions? [ ]
a) coupe b) saloon c) convertible d) estate
5. An enclosed two seater body having a fixed roof [ ] a) Couple b) Single c) Saloon d) None
6. The fundamental components fixed near to driver seat are [ ]
a) stereo b) air condition control c) steering, gear and foot control d) none 7. According to the visibility regulations,horizontal and vertical distance to be visible are [ ]
a) 12m,5m b) 10m,8m c) 8m,10m d) None 8. A fuse in an electrical circuit ‘blows’ as the result of a high [ ]
a) Voltage caused by a short circuit b) Current flow caused by a short circuit c) Voltage caused by an open circuit d) Current flow caused by an open circuit
9. In car a temperature indicating instrument is usually provided which indicates the temperature of [ ]
a) Engine piston b) Engine cylinder c) Lubricating oil d) Jacket cooling water 10. Noisy brakes indicate [ ]
a) rift on lining b) drums scored c) loose lining screws d) any of the above
Cont……..2
A
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
JNTUWORLD
Code No: A107412404 :2: Set No. 4
II Fill in the blanks 11. Fluid drive is one name for _____________ 12. The factor not considered to oppose the motion of the vehicle is ______________ 13. The part of the vehicle which holds the passengers and the cargo to be transported is known as
____________ 14. In a vehicle the probable cause for hard steering could be____________ 15. A frame consisting of side and cross members of channel section is normally used on____________ 16. As applied to the specification of a heavy commercial vehicle the abbreviation g.v.w is__________ 17. Most motor cars use a specially constructed body shell onto which the main components are
attached.It is called ____________ type 18. The type of engine used in a heavy commercial vehicle is _____________ 19. When a vehicle turns a corner, the action of the differential causes______________ 20. A collapsible steering column is one which collapses to ____________
-oOo-
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net