wayfinding and signage system - eugene, or
TRANSCRIPT
120 North Church Street
Suite 208
West Chester, PA 19380
T 484.266.0648
www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
Eugene, OregonWayfinding and Signage System
Parking Signage
DESIGN INTENT DRAWINGS
October 16, 2017
Table of Contents
Section 1 – SIGN SYSTEM STANDARDS A. Graphic Standards Typography Specifications ................................... A.1 Project Artwork ...................................................... A.4 Reflective and Opaque Vinyl Color Chart ........... A.5 Paint and Material Color Chart ............................ A.6
B. Placement Guidelines Vehicular Signage .................................................. B.1 Lateral Clearance ................................................... B.3
Section 2 – SIGNAGE DRAWINGS C. Menu of Sign Types Parking Directionals .............................................. C.1 Parking Garage ID .................................................. C.2 Parking Garage Interior Signs .............................. C.3
D. Design Intent Drawings PARK.1 ..................................................................... D.1 PARK.1a ................................................................... D.2 PARK.1b ................................................................... D.3 PARK.2 .................................................................... D.4 PARK.2a .................................................................. D.5 PARK.3 .................................................................... D.6 WDIR.1..................................................................... D.7 VINYL.1 ................................................................... D.8 PARK.4 .................................................................... D.9 PARK.5 .................................................................... D.10 PARK.6 .................................................................... D.11 PARK.6a .................................................................. D.12 PARK.7 ..................................................................... D.13 Broadway N Garage Entrance .............................. D.14 Broadway S Garage Entrance .............................. D.15 Hult Garage Entrance 1 ......................................... D.16 Hult Garage Entrance 2 ......................................... D.17 Hult Garage Entrance 3 ......................................... D.18 Hult Garage Entrance 4 ......................................... D.19 Overpark Entrance ................................................. D.20 Overpark Exit ......................................................... D.21 Parcade Entrance 1 ................................................ D.22 Parcade Entrance 2 ................................................ D.23 Pearl Street Garage Entrance ............................... D.24 OVD.1 ....................................................................... D.25 COLUMN.1 .............................................................. D.26 INFO.1 ...................................................................... D.27 SPACE.1 ................................................................... D.28 TEMP.1 ..................................................................... D.29 ELEVATOR.1 ............................................................ D.30 RULES.1................................................................... D.31 STAIR.1 .................................................................... D.32 STAIR.2 ................................................................... D.33 METER.1-2 ............................................................... D.34 BOOTH.1 ................................................................. D.35
E. Graphic Layouts PARK.1-2 .................................................................. E.1 PARK.3 .................................................................... E.2
F. Construction Details PARK.1-3 Section Details ...................................... F.1 Break-Safe Product Specifications ...................... F.2 Break-Safe Foundations ........................................ F.3 Plate-to-Plate Footer Details ................................ F.4 Footer Placement ................................................... F.5 Internally Illuminated Letters ............................... F.6
Graphic StandardsA
SPECIFICATIONS
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
A.1
The Clearview typeface is the required message font for vehicular sign types VDIR.1-6
All type shall be set exactly as specified. Substitutions will only be accepted, at the DESIGNER’S discretion, where they match the specified typeface in every detail. The FABRICATOR should be aware that different versions of typesetting equipment may not satisfactorily match specified typefaces and in such instances will not be acceptable.
TypographySpecifications
Clearview Highway
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz1234567890 ‘’!@#$%^
Amongst the several mechanical Arts that have engaged my attention, there is no one which I have pursued with so much steadiness and pleasure, as that of Letter Founding.
Downtown Downtown Downtown
123A 123A 123A
acceptable NOT acceptable NOT acceptable
acceptable NOT acceptable NOT acceptable
’'
This apostrophe is CORRECT.
Clearview Highway
This apostrophe is INCORRECT.
Sometimes the Foot mark is mistakenfor an apostrophe and an inch mark ismistaken for quotations. Below are examplesof correct and incorrect apostrophe’s foreach typeface.
PARK’S
PARK'S
TYPEFACE FOR: PARKING GUIDE SIGNS
SPECIFICATIONS
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
A.2
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Futura MediumABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz1234567890 !@#$%^Amongst the several mechanical Arts that have engaged my attention, there is no one which I have pursued with so much steadiness and pleasure, as that of Letter Founding.
Downtown Downtown Downtown
123A 123A 123Aacceptable NOT acceptable NOT acceptable
acceptable NOT acceptable NOT acceptable
Futura Book ObliqueABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz1234567890 !@#$%^Amongst the several mechanical Arts that have engaged my attention, there is no one which I have pursued with so much steadiness and pleasure, as that of Letter Founding.
Downtown Downtown Downtown
123A 123A 123Aacceptable NOT acceptable NOT acceptable
acceptable NOT acceptable NOT acceptable
Futura MediumABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz1234567890 !@#$%^Amongst the several mechanical Arts that have engaged my attention, there is no one which I have pursued with so much steadiness and pleasure, as that of Letter Founding.
Downtown Downtown Downtown
123A 123A 123Aacceptable NOT acceptable NOT acceptable
acceptable NOT acceptable NOT acceptable
Futura Book ObliqueABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz1234567890 !@#$%^Amongst the several mechanical Arts that have engaged my attention, there is no one which I have pursued with so much steadiness and pleasure, as that of Letter Founding.
Downtown Downtown Downtown
123A 123A 123Aacceptable NOT acceptable NOT acceptable
acceptable NOT acceptable NOT acceptable
TYPEFACE FOR: PARKING SIGNAGE
TypographySpecifications
The Futura Medium & Futura Book Oblique typefaces are utilized on the parking signs.
All type shall be set exactly as specified. Substitutions will only be accepted, at the DESIGNER’S discretion, where they match the specified typeface in every detail. The FABRICATOR should be aware that different versions of typesetting equipment may not satisfactorily match specified typefaces and in such instances will not be acceptable.
SPECIFICATIONS
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
A.3
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Typography Specifications
Individual spacing of each letter needs to be evaluated. All copy shall be kerned so that each character is optically centered between the center of each of the surrounding characters.
Eugene Eugene
Eugene Eugene
SIGN TEXT STANDARDS
LETTER-SPACING
IMPORTANT: Individual spacing of each letter needs to be evaluated. See Examples Above.Kern all Copy so that each character is optically centered between the center of each of the surrounding characters.
TYPEFACE 1 TYPEFACE 1
TYPEFACE 2 TYPEFACE 2
Inconsistencies in Letter Spacing Corrected Letter Spacing
XbaselinebaselineEjklHEjklH
COPY HEIGHT
When measuring copy height, measure only the height of the Capital lettersto determine your overall copy height (shown in illustration below as “X”)Some of the other letters have an extended height beyond the average height of the letters.
baselinebaseline
baselinebaseline
EjklHEjklHEjklHEjklH
LINE SPACING
X
When measuring line spacing, always measure from the baseline of the topmost text line to the baseline of the text line below (shown as “X”)
SPECIFICATIONS
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
A.4
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Artwork
ARROWS
SYMBOLS
USE of Arrows
When multiple directions arerequired on a sign, the followingdirectional hierarchy shall takeprecedent. See Example below.Reference Message Schedulefor individual Messages.
Utilized in Parking Directional signage
Utilized in Parking signage
Parking RestroomAccessibleE Park Logo
Left Arrow Up-Left Arrow Straight Arrow Up-Right Arrow Right Arrow
Straight-Left Arrow Up-Straight-Left Arrow Up-Straight-Right Arrow Straight-Right Arrow
Straight Arrow
Left Arrow
Right Arrow
parkeparkeugene.com
All artwork pictured on this page will be provided to the sign fabricator by the designer and/or client. This artwork must be used for all sign applications in this provided documentation. Do NOT substitute with any other artwork!
ARROWS
SYMBOLS
USE of Arrows
When multiple directions arerequired on a sign, the followingdirectional hierarchy shall takeprecedent. See Example below.Reference Message Schedulefor individual Messages.
Utilized in Parking Directional signage
Utilized in Parking signage
Parking RestroomAccessibleE Park Logo
Left Arrow Up-Left Arrow Straight Arrow Up-Right Arrow Right Arrow
Straight-Left Arrow Up-Straight-Left Arrow Up-Straight-Right Arrow Straight-Right Arrow
Straight Arrow
Left Arrow
Right Arrow
parkeparkeugene.com
SPECIFICATIONS
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
A.5
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Reflective and Opaque Vinyl
Color Chart
The FABRICATOR must submit three (3) identical sets of each color specified for approval prior to any painting. Sample paint swatches must be produced on .080" aluminum sheet, approximately 3" x 6", including primer and free of defects. Sample material swatches should be the same approximate size. Samples MUST have project and color specifications attached to back side.
The colors must look exactly the same every time they are used so that people associate them with the City of Eugene Wayfinding Program. All media, vinyl, paint, and inks must be produced so that the colors match as specified on this page.
White
Parking Blue
Teal
R REFLECTIVE VINYL NAME SPECIFICATION APPLICABLE PROCESS
R1
R2
R3
R4 Dark Gray
White
3M High Intensity Prismatic Reflective Sheeting 3930Color: White
3M High Intensity Prismatic Reflective Sheeting 3930Color Match: Pantone® 2388 C
3M High Intensity Prismatic Reflective Sheeting 3930Color Match: Pantone® Cool Gray 11 C
3M High Intensity Prismatic Reflective Sheeting 3930Color Match: Pantone® 2199 C
3M Scotchcal ElectroCut Opaque Vinyl Film7725-10 White
Custom Color: Background and Characters 3M custom inks direct to 3930 with 3M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet.
Custom Color: Background and Characters 3M custom inks direct to 3930 with 3M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet.
Custom Color: Background and Characters 3M custom inks direct to 3930 with 3M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet.
Knockout White: Background and Characters 3M custom inks direct to 3930 with 3M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet.
* MUST comply with MUTCD section Table 2A-3 – Minimum maintained retroreflectivity levels. Approved process: Durst RHO 161 TS printer. Sherine Industries: (604) 513-1887.NOTE: All 3M products are to be processed and applied according to 3M specifications. The seaming of material is NOT preferred. If the height of a sign panel is greater then 48 inches,the 3M 3930 material should be oriented vertically with stripes at 0 degrees, to avoid the seaming of material. If seaming is required, it should occur at the rule line or between messages.
Standard for System (typ.)
Standard for System (typ.)
Standard for System (typ.)
Standard for System (typ.)
Standard for System (typ.)
RedR5
R6 Yellow3M High Intensity Prismatic Reflective Sheeting 3930Color Match: Pantone® 121 C
3M High Intensity Prismatic Reflective Sheeting 3930Color Match: Pantone® 485 C
Custom Color: Background and Characters 3M custom inks direct to 3930 with 3M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet.
Custom Color: Background and Characters 3M custom inks direct to 3930 with 3M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet.
Standard for System (typ.)
Standard for System (typ.)
V VINYL NAME SPECIFICATION APPLICABLE PROCESS
V1 Surface applied according to 3M manufacturers specifications.
Surface applied according to 3M manufacturers specifications.
Black3M Scotchcal ElectroCut Opaque Vinyl Film7725-12 Black
Standard for System (typ.)V2 High resolution printed on White 3M Scotchcal Opaque Vinyl with 3M approved Clear UV/Graffiti overlaminate. Surface applied according to 3M manufacturers specifications.
High resolution printed on White 3M Scotchcal Translucent Vinyl with 3M approved Clear UV/Graffiti overlaminate. Surface applied according to 3M manufacturers specifications.
Parking Blue3M Scotchcal ElectroCut Opaque Vinyl FilmColor Match: Pantone® 2388 C
Standard for System (typ.)V3 High resolution printed on White 3M Scotchcal Opaque Vinyl with 3M approved Clear UV/Graffiti overlaminate. Surface applied according to 3M manufacturers specifications.
Frosted Crystal3M Scotchcal Frosted Crystal3M 7725SE-324
Standard for System (typ.)V4
Parking Blue3M Scotchcal ElectroCut Translucent Vinyl FilmColor Match: Pantone® 2388 C
Standard for System (typ.)V5
SPECIFICATIONS
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
A.6
The FABRICATOR must submit three (3) identical sets of each color specified for approval prior to any painting. Sample paint swatches must be produced on .080" aluminum sheet, approximately 3" x 6", including primer and free of defects. Sample material swatches should be the same approximate size. Samples MUST have project and color specifications attached to back side.
The colors must look exactly the same every time they are used so that people associate them with the City of Eugene Wayfinding Program. All media, vinyl, paint, and inks must be produced so that the colors match as specified on this page.
Paintand Materials Color Chart
Matthews Paint MP 11477
To match Pantone® 2388 C
To match Pantone® 2199 C
To match Pantone® Cool Gray 11 C
To match Pantone® 583 C
Standard for System (typ.) Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.
Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.
Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.
Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.
Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.
Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.
Standard for System (typ.)
Standard for System (typ.)
Standard for System (typ.)
Standard for System (typ.)
Standard for System (typ.)
P PAINTS NAME SPECIFICATION APPLICABLE PROCESS
P1
P2
P3
P4
P5
P6
White
Parking Blue
Teal
Green - Level 1
To match Pantone® 122 C Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.Standard for System (typ.)P7 Yellow - Level 2
Dark Gray
To match Pantone® 158 C
To match Pantone® 279 C
To match Pantone® 1805 C
To match Mathews Paint MP33653
Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.
Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.
Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.
Surface applied, exterior sign paint and protective top coat:MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish.
Standard for System (typ.)
Standard for System (typ.)
Standard for System (typ.)
Standard for System (typ.)
P8
P9
P10
P11
Orange- Level 3
Red - Level 5
Black Stallion
Blue - Level 4
Willam
ette
Broadway
8th Ave
7th Ave
6th Ave
10th Ave
11th Ave
Olive
Charn
elton
Oak
Pearl
2
3
4
7
8
426
55
Willamette River
Willa
mette
Riv
er
ParkBlocks
Skinner Butte Park
Kiwanis Park
Alton BakerPark
Ruth Bascom Bike Path
Ruth
Basco
m B
ike P
ath
Ruth
Basc
om
Bik
e P
ath
Pearl A
lley
Hig
h A
lley
Oak A
lley
Mill A
lley
Ferry
Alle
y
Patte
rson
Alle
y
Broadway Alley
Ch
am
elto
n A
lley
Lin
co
ln A
lley
Law
ren
ce A
lley
12th Alley
11th Ave
12th Ave 12th Ave
13th Ave 13th Ave
10th Ave
Broadway Broadway Broadway
8th Ave
7th Ave
6th Ave
6th Ave
5th Ave 5th Ave
4th Ave
Cobur
g R
d
Fer
ry S
t Bridge
Co
burg
Rd
3rd Ave
2nd Ave
4th Ave
3rd Ave
3rd Ave
Skinner Butte Loop
2nd Ave
1st Ave
Clark St
Chesire Ave
Chesire Ave
Floral Ave
Shelton McMurphey Blvd
11th Ave
10th Ave
8th Ave
7th Ave
6th Ave
Oliv
e S
t
Ch
arn
elto
n S
tC
harn
elto
n S
t
Willa
me
tte S
tW
illam
ette
St
Willa
me
tte S
t
Oak S
t
Oliv
e S
t
Ch
arn
elto
n S
t
Oak S
t
Pearl S
tP
earl S
t
Lin
co
ln S
t
Law
ren
ce S
t
Wash
ing
ton
St
Oliv
e S
t
Ch
arn
elto
n S
t
Lin
co
ln S
t
Law
ren
ce S
t
Wash
ing
ton
St
Lin
co
ln S
t
Law
ren
ce S
t
Wash
ing
ton
St
Lin
co
ln S
tL
inco
ln S
t
Law
ren
ce S
t
Wash
ing
ton
St
Law
ren
ce S
t
Wash
ing
ton
St
Law
ren
ce S
t
Wash
ing
ton
St
Hig
h S
tH
igh
St
Ferry
St
Pearl S
t
Hig
h S
t
Mill S
tM
ill St
Oak S
t
Pearl S
t
Hig
h S
t
Mill S
t
Ferry
St
Patte
rson
St
Hilly
ard
St
Patte
rson
St
Hilly
ard
St
S Park St
W P
ark
St
11
17
13
10
25
28
2
23
22
27
18
5
21
20
19
3
7
8
16
4
26
6
914
12
1
Hult Garage
AmtrakLot
Ferry StreetBridge Lot
ParcadeGarage
Pearl StGarageO
verp
ark
Gara
ge
Broadway Place N.
Broadway Place S.
PublicParking
Federal Courthouse Lot
EWEBRiverfront
Lot
Hult Garage
AmtrakLot
Ferry StreetBridge Lot
ParcadeGarage
Pearl StGarageO
verp
ark
Gara
ge
Broadway Place N.
Broadway Place S.
PublicParking
Federal Courthouse Lot
EWEBRiverfront
Lot
99
99
99
9999
9999
105
i
EW
The Columns
YOU ARE HERE
5 M
IN W
AL
K5
MIN
WA
LK
5 M
IN W
AL
K5
MIN
WA
LK
5 M
IN W
AL
K
DOWNTOWNActors CabaretEugene Saturday MarketHult CenterJapanese/American Art MemorialKesey PlazaLane Community College-DowntownMcDonald TheaterOregon Contemporary TheatreRiver Play - Discovery Village PlaygroundRiverfront Plaza
1
4
7
8
9
10
12
14
18
19
20
21
22
23
25
26
27
28
Shedd InstituteShelton McMurphey Johnson HouseSkinner ‘s CabinSkinner Butte ParkVisitor CenterFree Speech PlazaWJ Skatepark + Urban PlazaWOW Hall
i
Amtrak Train StationGreyhound Bus DepotLane Transit District (LTD) Eugene Station
2
6
11
LEGEND Visitor Information
Public Parking
Train Station
Bus Station
Public Restroom
Parks
Pedestrian / Bike Trail
ARTS & CULTURE
TRANSPORTATION
County CourthouseFederal CourthouseMunicipal CourthousePost O�cePublic Library
3
5
13
16
17
GOVERNMENT / COMMUNITY
MunicipalCourt Lot
Aluminum Dye-Sub Print Aluminum panel with Dye-Sub Print graphics
M MATERIALS NAME SPECIFICATION PROCESS
M1 Dye-Sub Print
To match Mathews Paint MP18082Brightray Silver Metallic
Placement GuidelinesB
SPECIFICATIONS
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
B.1
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Placement Guidelines
FIGURE 1 - Parking Directional - Sign Placement GuidelineFIGURE 2 - Parking Identification - Sign Placement Guideline
Unless approved by the Client or its designated agent, all signs shall be installed to the right of the direction of traffic and where sufficient space is available.
(a) Signs shall be located to take advantage of natural terrain, to minimize impacts on scenic environment and to avoid visual conflicts with other signs, trees and lampposts within the City right-of-way.
(b) Signs shall be located so as not to interfere with, obstruct or divert driver’s attention from any other Official Traffic Control Device. Other Official Traffic Control Devices placed at intersection approaches, subsequent to the placement of a Wayfinding Sign, shall have precedence as to location and may require the relocation of the Wayfinding Sign. In the locations where Official Traffic Control Devices are integrated into the Wayfinding Signage System, the Official Traffic Control Devices shall take precedence with regard to order, space and location, over other information.
(c) Wayfinding Signs shall be positioned in such a manner that does not restrict driver’s attention or view when making turns or driving through an intersection. (d) There shall be a goal of one sign per block, although two are permissible, where necessary.
The following pages illustrate installation guidelines for the location and spacing of the various sign types. Figures 1 through 6 represent the guidelines for the location of the various sign types, while Figure 7 illustrates the lateral clearance guidelines.
Figure 1
Sign A: PARK.1-2
Figure 2
Sign B: PARK.1-2
B
B
50 to
100
ft.
50 to
100
ft.
Parking Lot
Entrance
Destination
A
A
Not
less
than
50
ft.N
ot le
ss th
an 2
5 ft.
D
ista
nce
betw
een
2 si
gns
100
to 2
00 ft
.Pr
iorit
y pl
acem
ent
SPECIFICATIONS
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
B.2
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Placement Guidelines
FIGURE 3 - Parking Directional - Sign Placement GuidelineFIGURE 4 - Parking Directional - Sign Placement Guideline
Unless approved by the Client or its designated agent, all signs shall be installed to the right of the direction of traffic and where sufficient space is available.
(a) Signs shall be located to take advantage of natural terrain, to minimize impacts on scenic environment and to avoid visual conflicts with other signs, trees and lampposts within the City right-of-way.
(b) Signs shall be located so as not to interfere with, obstruct or divert driver’s attention from any other Official Traffic Control Device. Other Official Traffic Control Devices placed at intersection approaches, subsequent to the placement of a Wayfinding Sign, shall have precedence as to location and may require the relocation of the Wayfinding Sign. In the locations where Official Traffic Control Devices are integrated into the Wayfinding Signage System, the Official Traffic Control Devices shall take precedence with regard to order, space and location, over other information.
(c) Wayfinding Signs shall be positioned in such a manner that does not restrict driver’s attention or view when making turns or driving through an intersection. (d) There shall be a goal of one sign per block, although two are permissible, where necessary.
The following pages illustrate installation guidelines for the location and spacing of the various sign types. Figures 1 through 6 represent the guidelines for the location of the various sign types, while Figure 7 illustrates the lateral clearance guidelines.
Figure 3
Sign C: PARK.1-2
Figure 4
Sign D: PARK.1-2
D
D
Not
less
than
25
ft.N
ot le
ss th
an 5
0 ft.
D
D
Not
less
than
25
ft.N
ot le
ss th
an 5
0 ft.
C
C
Position Center of Island
Not
less
than
25 ft
.N
ot le
ss th
an 2
5 ft.
100
to 2
00 ft
.
SPECIFICATIONS
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
B.3
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Placement Guidelines
a
c
b
d
e
f
g
h
FIGURE 6 - Lateral Clearance Guidelines
Within some of the Downtown areas of City of Eugene, urban conditions and narrow sidewalks may cause deviation from the standards articulated in the previous figures. Conditions may include less lateral clearance for the 2'-0" or 5'-0" preferred distance from edge of sign panel to curb, or placement at 2'-0" or 5'-0" would create an obstacle (i.e. post positioned in middle of the side walk) or create situations of non-compliance to ADA clearances.
In these cases guidelines must be consistent with MUTCD Section 2A.19 options for urban areas.
Suggested recommendations for relocation of signs if placement is in conflict with guidelines.
OPTION A: Position the sign at a minimum of 2'-0" or 5'-0" (face of curb to edge of sign panel) as required.
OPTION B: If the sign can be moved, without disrupting routing or sequencing, then it should be repositioned to achieve the 2'-0" or 5'-0" min.
If 2'-0" is not physically possible, then the following options should be allowed:
OPTION C: The sign set back should be position at 1'-6". If that is not possible then...
OPTION D: Utilize a minimum 1'- 0", in accordance with MUTCD, only as a final option.
Figure 6
Not to Scale
MEASURE PREFFERED DISTANCE MINIMUM DISTANCESIGN TYPE
aDistance from Edge of Sign Panel toEdge of Curb
2'-0" or more 1' - 0"
b
c
Distance from Sign Post toNearest Obstruction
4' - 0" or more 3' - 0"
Distance from Edge of Sign Panel toNearest Overhead Obstruction
4' - 0" or more 1' - 0"
dSign Placement in Relation to Adjacent Building
align to building Edge Do Not obstruct Entrance
eDistance from Face of Sign toNearest Tree Branch
20' - 0" or more 15' - 0"
fDistance from Face of Sign toNearest Utlity Pole
15' - 0" or more 10' - 0"
gDistance from Back of Sign toNearest Tree Branch
8' - 0" or more 3' - 0"
hDistance from Back of Sign toNearest Utility Pole
15' - 0" or more 10' - 0"
Measurements and Distances shown are guidelines only prevailing local and state codes shall supersede information presented.
SPECIFICATIONS
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
B.4
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Placement Guidelines
FIGURE 7 - Lateral Clearance Guidelines
Within some of the Downtown areas of City of Eugene, urban conditions and narrow sidewalks may cause deviation from the standards articulated in the previous figures. Conditions may include less lateral clearance for the 2'-0" or 5'-0" preferred distance from edge of sign panel to curb, or placement at 2'-0" or 5'-0" would create an obstacle (i.e. post positioned in middle of the side walk) or create situations of non-compliance to ADA clearances.
In these cases guidelines must be consistent with MUTCD Section 2A.19 options for urban areas.
Suggested recommendations for relocation of signs if placement is in conflict with guidelines.
OPTION A: Position the sign at a minimum of 2'-0" or 5'-0" (face of curb to edge of sign panel) as required.
OPTION B: If the sign can be moved, without disrupting routing or sequencing, then it should be repositioned to achieve the 2'-0" or 5'-0" min.
If 2'-0" is not physically possible, then the following options should be allowed:
OPTION C: The sign set back should be position at 1'-6". If that is not possible then...
OPTION D: Utilize a minimum 1'- 0", in accordance with MUTCD, only as a final option.
Example of Sidewalk & City Right of Way (Sidewalk widths vary)
5’-0” 9’-0”
Gutter Curb
AD
A required
3'-0" minim
um
2’-0” typ. to Curb(1’-0” Min.) Sign Panel
Pole/Breakaway
5 Foot Furnishing Zone
Sidewalk Element:Canopy, Bench, Tree-grateStairs, Building Entrance, etc.
Reference View: Example - 5 foot Furnishing Zone / City Right of WaySCALE: Not To Scale
Note: Top View of PARK.1-2 shown as example.
1
NOTE:All locations shall be installed within the City ROW. If during the initial survey it is determined any part of the sign (pole or panel) extends outside of the City’s Right of Way vertical plane and into private property, the installer must notify the city prior to fabrication/installation.
Figure 7
Not to Scale
Menu of Sign TypesC
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
C.1
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Parking Directional & Lot ID Signage Overview
MENU OF SIGN TYPESParking Directional Parking Lot ID
PARK.1Parking Trailblazer
PARK.1aParking Trailblazer
PARK.2aParking Directional
PARK.1bParking Trailblazer
(Combine w/ existingOne-way sign. New Pole)
PARK.2Parking Directional
PARK.3Parking IDMonument
VINYL.1Door Vinyl
Pedestrian Garage Entrance
WDIR.1Wall Directional
PedestrianParking Access
249 West Broadway
Elevator to all Parking Levels
Stairs up to Parking Level 1
Stairs down to Parking Levels 2 & 3
PUBLIC PARKING
Broadway Place South
Hult CenterParking
NEXT LEFT
Hult CenterParking
NEXT LEFT
MunicipalCourt Lot
PUBLICPARKING
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
C.2
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Exterior Parking Garage Signage Overview
MENU OF SIGN TYPESParking Garage Signage - Exterior
PARK.5Parking Garage IDEntrance / Exit Sign
ENTRANCEEXIT
LED Lighting
PARK.4Parking Garage IDIlluminated Letters
P E A R L S T R E E T G A R A G EP E A R L S T R E E T G A R A G E
PERMIT PARKING
ONLY
EXCEPT AT METERS
8am-5pmMon-Fri
parkeparkeugene.comPARK.7
Parking GarageInformational Sign
PARK.6 or PARK.6aParking Garage IDFlag Mounted Sign
PARK.6 PARK.6a
PUBLICPARKING
PUBLICPARKING
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
C.3
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Interior Parking Garage Sign Overview
MENU OF SIGN TYPESInterior Parking Garage Signs
3NORTH
ELEVATORIS OUT
parkeparkeugene.com
PLEASE USE SOUTH OR EAST ELEVATORS
3NORTH STAIRExit to 10th Ave
EXIT
Exit to 10th AveNORTH STAIR
PERMITPARKING
ONLY7AM-6PMMON-FRI
PARK
RATES
PAYHERE
LEVELS2,3,4
PERMITPARKING
ONLY
Exit to 10th AveNORTH ELEVATOR
ATTENTION
11”x17”Insert
11”x17”Insert
COLUMN.1Level ID
Column Wrap
OVD.1Overhead Vehicular
Directional
INFO.1Garage Info
ELEVATOR.1Elevator ID
SPACE.1Parking Space ID
TEMP.1Temporary Sign
RULES.1Garage Rules
STAIR.1Overhead Stairwell ID
STAIR.2Stairwell ID
Wall or Column
METER.1“Pay Here”
METER.2Parking Rates
Design Intent DrawingsDS
V8 9
Specification Note
Color Designator
The Color Designator Chart is found in theGraphic Standards section.
The Specification Notation is found on thesame page as the drawings.
KEY:
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.1
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type PARK.1 Parking Trailblazer
Parking TrailblazerPARK.1
1. 4x4 SQUARE POST MATERIAL: 4"x4"x.25" Square Aluminum Post. FABRICATION PROCESS: Extruded EDGES: Smooth COLOR: Custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
FOOTER: Transpo Breakaway. As per ODOT Specs.
2. MOUNTING BRACKET MATERIAL: 3/16" thick Aluminum U-Channel FABRICATION PROCESS: Extruded EDGES: Square, Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
FASTENER: Tamper-resistant mechanically fastened to Post.
3. 1/4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: 1/4" thick Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted GRAPHIC BACKGROUND AND COPY PROCESS:
3M custom inks print direct to 3930 with 3M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications)
FASTENER: Press-roll per 3M requirements. Weld back of panel to mounting bracket.
EDGE DETAIL: Paint all edges and back with Matthews Acrylic Polyurethane, with clear coat satin finish.
50. BREAKAWAY FOOTER FOOTER: Transpo® Break-Safe AS4 break-away
support system, as per ODOT break-away specs.
Side View
Top View
Back ViewFront View: PARK.1SCALE: 1/2" = 1'-0"1
Graphic Layout: PARK.1SCALE: 1 1/2" = 1'-0"2
F.11
R2 3
R1 3
R1 3
P2 2 P2 2
R4 3
P11 1
P11 50
10'-6"
1'-6"
4" 1'-2"CL
2'-7"
7'-6"
2'-0" Min
2'-7"
1'-6"
1'-1"
CL
C LC L7 1/4"
1'-6"
Ø 1'-2"
Ø 1'-0 1/4"
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.2
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type PARK.1a Parking Trailblazer
Parking TrailblazerPARK.1a
4. POLE STRAP ATTACHMENT PRODUCT: Band-It Band, or approved equal. MATERIAL: Type 201 SS SIZE: 3/4 inch COLOR: To Match Pole existing color. Utlize
Color-It ® Polyester Coating FASTENER: Universal Channel Clamp-SignFix
SX0220 NOTE: Sign Contractor to coordinate the
removal or movement of interfering existing signs on utility poles, with the city.
2. MOUNTING BRACKET MATERIAL: 3/16" thick Aluminum U-Channel FABRICATION PROCESS: Extruded EDGES: Square, Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
FASTENER: Weld to back of Sign Panel. SS strap-mounted to utility pole.
6. 1/8" SIGN PANEL FRONT - REFLECTIVE MATERIAL: 1/8" thick Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted GRAPHIC BACKGROUND AND COPY PROCESS:
3M custom inks print direct to 3930 with 3M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications)
FASTENER: Press-roll per 3M requirements. Weld back of panel to mounting bracket.
EDGE DETAIL: Paint all edges and back with Matthews Acrylic Polyurethane, with clear coat satin finish.
Side View Back ViewFront View: PARK.1aSCALE: 1/2" = 1'-0"1
Top View: PARK.1aSCALE: NTS2
4"
1 1/
2"
Weld Panel to bracket
Graphic Layout: PARK.1SCALE: 1 1/2" = 1'-0"2
2'-7"
1'-6"
1'-1"
CL
C LC L7 1/4"
1'-6"
Ø 1'-2"
Ø 1'-0 1/4"
R2 6 P11 4
P2 2
P2 6R1 6
R4 6
Existing PostFabricator must verify posts are structurallyengineered to hold sign panels.
1'-6"
2'-7"
7'-6"
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.3
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Side View
Top View
Back ViewFront View: PARK.1bSCALE: 1/2" = 1'-0"1
Graphic Layout: PARK.1bSCALE: 1 1/2" = 1'-0"2
F.13
C L
CL
R2 3
R1 3P2 3
R4 3
P11 1
P11 50
2'-0" Min
1'-0"
1'-6"
7'-6"
10'-6"
3'-0"
Re-Use Existing One Way SignsReplace location w/ new sign
7 1/4"
Ø 1'-2"Ø 1'-0 1/4"
1'-4" 1'-8"
Sign Type PARK.1b Parking Trailblazer
Parking TrailblazerPARK.1b
1. 4x4 SQUARE POST MATERIAL: 4"x4"x.25" Square Aluminum Post. FABRICATION PROCESS: Extruded EDGES: Smooth COLOR: Custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
FOOTER: Transpo Breakaway. As per ODOT Specs.
3. 1/4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: 1/4" thick Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted GRAPHIC BACKGROUND AND COPY PROCESS:
3M custom inks print direct to 3930 with 3M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications)
FASTENER: Press-roll per 3M requirements. Mechanically fasten to sign post. EDGE DETAIL: Paint all edges and back with Matthews Acrylic Polyurethane, with clear coat satin finish.
50. BREAKAWAY FOOTER FOOTER: Transpo® Break-Safe AS4 break-away
support system, as per ODOT break-away specs.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.4
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type PARK.2 Parking Trailblazer
Parking TrailblazerPARK.2
1. 4x4 SQUARE POST MATERIAL: 4"x4"x.25" Square Aluminum Post. FABRICATION PROCESS: Extruded EDGES: Smooth COLOR: Custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
FOOTER: Transpo Breakaway. As per ODOT Specs.
2. MOUNTING BRACKET MATERIAL: 3/16" thick Aluminum U-Channel FABRICATION PROCESS: Extruded EDGES: Square, Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
FASTENER: Tamper-resistant mechanically fastened to Post.
3. 1/4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: 1/4" thick Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted GRAPHIC BACKGROUND AND COPY PROCESS:
3M custom inks print direct to 3930 with 3M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications)
FASTENER: Press-roll per 3M requirements. Weld back of panel to mounting bracket.
EDGE DETAIL: Paint all edges and back with Matthews Acrylic Polyurethane, with clear coat satin finish.
50. BREAKAWAY FOOTER FOOTER: Transpo® Break-Safe AS4 break-away
support system, as per ODOT break-away specs.
Side View
Top View
Back ViewFront View: PARK.2SCALE: 1/2" = 1'-0"1
Hult CenterParking
NEXT LEFT
F.11
P2 2
P2 3
R2 3
R1 3
R4 3
P11 1
P11 50
2'-0" Min
3'-2"
7'-6"
2'-3"
11'-1"
4" 1'-11"
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.5
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type PARK.2a Parking Trailblazer
Parking TrailblazerPARK.2a
4. POLE STRAP ATTACHMENT PRODUCT: Band-It Band, or approved equal. MATERIAL: Type 201 SS SIZE: 3/4 inch COLOR: To Match Pole existing color. Utlize
Color-It ® Polyester Coating FASTENER: Universal Channel Clamp-SignFix
SX0220 NOTE: Sign Contractor to coordinate the
removal or movement of interfering existing signs on utility poles, with the city.
2. MOUNTING BRACKET MATERIAL: 3/16" thick Aluminum U-Channel FABRICATION PROCESS: Extruded EDGES: Square, Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
FASTENER: Weld to back of Sign Panel. SS strap-mounted to utility pole.
6. 1/8" SIGN PANEL FRONT - REFLECTIVE MATERIAL: 1/8" thick Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted GRAPHIC BACKGROUND AND COPY PROCESS:
3M custom inks print direct to 3930 with 3M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications)
FASTENER: Press-roll per 3M requirements. Weld back of panel to mounting bracket.
EDGE DETAIL: Paint all edges and back with Matthews Acrylic Polyurethane, with clear coat satin finish.
Side View Back ViewFront View: PARK.2aSCALE: 1/2" = 1'-0"1
Hult CenterParking
NEXT LEFT
Top View: PARK.2aSCALE: NTS2
4"
1 1/
2"
Weld Panel to bracket
Existing PostFabricator must verify posts are structurallyengineered to hold sign panels.
R2 6P11 4
P2 2 P2 6
R1 6
R4 6
2'-3"
3'-2"
7'-6"
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.6
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type PARK.3 Parking Lot ID
Parking Lot IDPARK.3
3. 1/4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: 1/4" thick Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted GRAPHIC BACKGROUND AND COPY PROCESS:
3M custom inks print direct to 3930 with 3M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications)
FASTENER: Press-roll per 3M requirements. Mechanically fasten to sign cabinet.
EDGE DETAIL: Paint all edges and back with Matthews Acrylic Polyurethane, with clear coat satin finish.
5. SIGN CABINET MATERIAL: Aluminum extrusion and sheet FABRICATION PROCESS: Extruded framing / Fabricated, with hidden fasteners. EDGES: Square, Smooth COLOR: Custom, as noted
FACE: GRAPHIC BACKGROUND AND COPY PROCESS: 3M custom inks print direct to 3930 with 3M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) Press-roll per 3M requirements.
SURFACE PROCESS: Paint all exposed surfaces with Matthews Acrylic Polyurethane, with clear coat satin finish.
FASTENERS: Cabinet mechanically fastened to internal support, attaches to footer.
7. PARKING SYMBOL MATERIAL: 1" deep Aluminum Reverse channel
symbol FABRICATION PROCESS: Router Cut. EDGES: Square, Smooth SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
FASTENER: Pin-mount flush to cabinet surface.
Side View
Top View
Back ViewFront View: PARK.3SCALE: 1/2" = 1'-0"1
MunicipalCourt Lot
PUBLICPARKING
MunicipalCourt Lot
PUBLICPARKING
F.12
P2 5
P1 7
R4 3
R1 3
R3 3
2'-3"
8'-4"
1'-8"
5'-3"
2'-0 1/2"5"Ø 1'-3"
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.7
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type WDIR.1 Pedestrian Wall Directional
Wall DirectionalWDIR.1
8. GRAPHIC PANEL MATERIAL: 1/4" thk. alum. panel
FABRICATION PROCESS: Router Cut EDGES: Square, Smooth SURFACE PRINT PROCESS: Zero VOC Powdercoat
Primer w/ Water Based Custom Dye Sublimated Ink Transfer Print on Face + Back of Panel Clear UV-Resistant, Anti-Graffiti Powdercoat Topcoat, Matte/Satin Finish (Per Manufacturer Capabilities
FASTENER: Pin-mount to wall/ column with tamper-resistant hardware. If located on Brick: Locate holes in grout lines.
Conditions vary by location. Fabricator to verify all measurements and mounting conditions in field.
Side ViewFront View: WDIR.1SCALE: 1/2" = 1'-0"1
PedestrianParking Access
2'-3"
1/4"
Section: WDIR.1SCALE: 1 1/2" = 1'-0"2
M1 8
1'-5"
2'-3"
4'-11"
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.8
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type VINYL.1 Door Vinyl
Door VinylVINYL.1
Front View: VINYL.1SCALE: 1/2" = 1'-0"1
Front View: VINYL.1SCALE: 1 1/2" = 1'-0"2
249 West Broadway
Elevator to all Parking Levels
Stairs up to Parking Level 1
Stairs down to Parking Levels 2 & 3
PUBLIC PARKING
Broadway Place South
*MUST VERIFY DIMNESIONS OF OPENING IN FIELD
Elevator to all Parking Levels
Stairs up to Parking Level 1
Stairs down to Parking Levels 2 & 3
PUBLIC PARKING
Broadway Place South
V3 9
V1 9
3'-9"Fabricator to
VIF in Field
2'-5"Fabricator to
VIF in Field
6"
1 1/4"1 1/2"3/4"
1 1/2"1"1"
4 1/4"
1"1/2"
1 1/4"
3/4"1 1/2"3/4"
1"
3/4"1 1/4"
9. VINYL ON GLASS MATERIAL: 3M Exterior grade Opaque Vinyl COLOR: as noted FASTENER: Adhere to face of glass per 3M
specifications
FABRICATOR MUST TAKE MEASUREMENTS OF EACH ENTRY SITE PRIOR TO ORDERING MATERIALS.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.9
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type PARK.4 Parking Garage ID Illuminated Letters
Parking Garage IDPARK.4
Front View: PARK.4SCALE: 1/4" = 1'-0"1
P E A R L S T R E E T G A R A G E
H U L T G A R A G E
B R O A D W A Y S O U T H G A R A G E
B R O A D W A Y N O R T H G A R A G E
O V E R P A R K G A R A G E
P A R C A D E
P A R C A D E G A R A G E
– 10
10"
10"
10"
10"
1'-0"
1'-6"
1'-6"
10. PIN-MOUNT LETTERS - FACE LIT MATERIAL: 2" thk Reverse channel individual
letters, painted silver on sides. LED white lights. (4000K exterior LEDs)
PRODUCT: BitroGroup Resno Face Lit Letters RS-AC-F2 (Or approved equal)
EDGES: Smooth SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
FASTENER: Pin-mount to garage facade.
NOTE: Conditions Vary per location. Fabricator to field verify prior to fabrication.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.10
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type PARK.5 Exit/Entrance
Parking Garage
Exit/EntrancePARK.5
Front View: PARK.5SCALE: 1/4" = 1'-0"1
ENTRANCE
EXIT
1'-2"
1/2"
1'-2"
1/2"
Section Details: PARK.5SCALE: 1" = 1'-0"2
1. Flat Mount: Brick 2. Flat Mount: Concrete 3. Floating : Side View 4. Floating : Top View
MOUNTING EXAMPLES
1'-2" 9" 8"
1'-2" 8"
Varies Per LocationFabricator Must Verify in Field
Varies Per LocationFabricator Must Verify in Field
R1 11
R4 11
R1 11
R2 11
11. 1/2" SIGN PANEL FRONT - REFLECTIVE MATERIAL: 1/2" thick Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted GRAPHIC BACKGROUND AND COPY PROCESS:
3M custom inks print direct to 3930 with 3M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications)
FASTENER: Press-roll per 3M requirements. Mechanically Fasten to Parking Garage Structure. Varies per location.
EDGE DETAIL: Paint all edges with Matthews Acrylic Polyurethane, with clear coat satin finish.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.11
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type PARK.6 Parking Garage ID
Flag Sign
Parking Garage IDPARK.6
12. SIGN STRUCTURE Material: Aluminum Process: Fabricated/ Welded H type construction Surface Process: Paint as indicated Color: As indicated in Color Chart Internal Bracing: As reqd. by sign manufacturers Structural engineer. Fabricators drawings are to
be signed and sealed by a certified State of OR licensed Structural Engineer.
SIGN FACE Sign Panel: Flexible Face Clip Mounting System Vinyl: 3M Scotchcal Translucent Graphic Film as
specified Diffuser: 3M Diffuser Film as specified Substrate: 3M Panaflex 945 as specified Color: As indicated in Color Chart INTERNAL LED LIGHT FIXTURE Lighting Process: Internal Face Lit Manufacturer: Sylvania LED #OSDC36w2-865- Exterior or approved equal. Color: White Fasten: Mount to inside of Logo, provide rear
baffle at rear with second row of LEDs.
INTERNAL LED HOUSING Material: Aluminum Process: Fabricated/ Welded H type construction Surface Process: Paint as indicated Color: As indicated in Color Chart Internal Bracing: As reqd. by sign manufacturers Structural engineer. Fabricators drawings are
to be signed and sealed by a certified State of Pennsylvania licensed Structural Engineer.
HARDWARE MOUNTING METHOD: Mechanically Fasten MATERIAL: Stainless Steel TYPE: Screw with threaded anchor insert. SIZE: as determined by Fabricator MOUNTING SURFACE: Concrete or Brick VIF
Conditions vary by location. Fabricator to verify all measurements and mounting conditions in field.
Side View
PUBLICPARKING
Front View: PARK.6SCALE: 1/2" = 1'-0"1
Reco
mm
end 1
2' –
14'-0
" abo
ve St
reet
or Si
dewa
lk
P5 12
P3 12
P4 12
V5 12
Section View: PARK.6SCALE: 1 1/2" = 1'-0"4
Detail: PARK.6SCALE: NTS3
Electrical thru-hole
2'-5"
2'-5"
1'-6"
3'-11"
2'-5" 6"
5"
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.12
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type PARK.6a Parking Garage ID
Flag Sign
Parking Garage IDPARK.6a
12. SIGN STRUCTURE Material: Aluminum Process: Fabricated/ Welded H type construction Surface Process: Paint as indicated Color: As indicated in Color Chart Internal Bracing: As reqd. by sign manufacturers Structural engineer. Fabricators drawings are to
be signed and sealed by a certified State of OR licensed Structural Engineer.
SIGN FACE Sign Panel: Flexible Face Clip Mounting System Vinyl: 3M Scotchcal Translucent Graphic Film as
specified Diffuser: 3M Diffuser Film as specified Substrate: 3M Panaflex 945 as specified Color: As indicated in Color Chart INTERNAL LED LIGHT FIXTURE Lighting Process: Internal Face Lit Manufacturer: Sylvania LED #OSDC36w2-865- Exterior or approved equal. Color: White Fasten: Mount to inside of Logo, provide rear
baffle at rear with second row of LEDs.
INTERNAL LED HOUSING Material: Aluminum Process: Fabricated/ Welded H type construction Surface Process: Paint as indicated Color: As indicated in Color Chart Internal Bracing: As reqd. by sign manufacturers Structural engineer. Fabricators drawings are
to be signed and sealed by a certified State of Pennsylvania licensed Structural Engineer.
HARDWARE MOUNTING METHOD: Mechanically Fasten MATERIAL: Stainless Steel TYPE: Screw with threaded anchor insert. SIZE: as determined by Fabricator MOUNTING SURFACE: Concrete or Brick VIF
Conditions vary by location. Fabricator to verify all measurements and mounting conditions in field.
Side View
PUBLICPARKING
Front View: PARK.6aSCALE: 1/2" = 1'-0"1
Reco
mm
end 1
2' –
14'-0
" abo
ve St
reet
or Si
dewa
lk
P5 12
P3 12
P4 12
V5 12
Section View: PARK.6aSCALE: 1 1/2" = 1'-0"4
Detail: PARK.6aSCALE: NTS3
Electrical thru-hole
3'-0"
3'-0"
1'-10"
4'-10"
3'-0" 6"
5"
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.13
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type PARK.7 Garage Info
Garage InfoPARK.7
FREE PARKINGSATURDAY & SUNDAY
Except Event Parking
parkeparkeugene.com
Side ViewFront View: PARK.7SCALE: 1/2" = 1'-0"1
3'-0"
1/4"
Section: PARK.7SCALE: 1" = 1'-0"2
P3 13
P2 13
P4 13
P1 133'-0"
4'-11"
2'-5"
Final text TBDby client
13. SIGN PANEL - DIGITAL PRINT MATERIAL: 1/4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
GRAPHIC BACKGROUND AND COPY PROCESS: 3M custom inks print direct to Scotchcal ® #3690 with 3M approved UV/Graffiti Vinyl Overlaminate. (See Color Sheet for all color and material specifications)
FASTENER: Pin-mount to wall/ column with tamper-resistant hardware. If located on Brick: Locate holes in grout lines.
Conditions vary by location. Fabricator to ≠verify all measurements and mounting conditions in field.
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.14
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Broadway North Garage Entrance
LED LightingPARK.5Parking Garage IDEntrance / Exit Sign
PARK.4Parking Garage IDIlluminated Letters
ENTRANCEEXIT
B R O A D W A Y N O R T H G A R A G EB R O A D W A Y N O R T H G A R A G E
FREE PARKINGSATURDAY & SUNDAY
Except Event Parking
parkeparkeugene.com
PARK.6Parking Garage ID
Flag Mounted Sign
PARK.7Parking Garage
Informational Sign
Front View: Broadway North EntranceSCALE: 3/8" = 1'-0"1
12'-9" VIF 12'-9" VIF
*Fabricator MUST verify all measurements in �eld prior to fabrication
Remove existing signs: 1. Garage Name Letters2. Garage Info3. Flag mounted sign
Re-surface garage where needed prior to installation of new signs. (Patch/Paint)
Measurements given as an estimate only. The fabricator MUST verify all measurements for signs in field prior to fabrication.
1
23
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.15
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Broadway South Garage Entrance
LED LightingPARK.5Parking Garage IDEntrance / Exit Sign
PARK.4Parking Garage IDIlluminated Letters
ENTRANCEEXIT
B R O A D W A Y S O U T H G A R A G EB R O A D W A Y S O U T H G A R A G E
FREE PARKINGSATURDAY & SUNDAY
Except Event Parking
parkeparkeugene.com
PARK.6Parking Garage ID
Flag Mounted Sign
PARK.7Parking Garage
Informational Sign
Front View: Broadway South EntranceSCALE: 3/8" = 1'-0"1
12'-9" VIF 12'-9" VIF
*Fabricator MUST verify all measurements in �eld prior to fabrication
1
23
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
Remove existing signs: 1. Garage Name Letters2. Garage Info3. Flag mounted sign
Re-surface garage where needed prior to installation of new signs. (Patch/Paint)
Measurements given as an estimate only. The fabricator MUST verify all measurements for signs in field prior to fabrication.
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.16
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Hult Garage Entrance 1
H U L T G A R A G EH U L T G A R A G E
ENTRANCE
PARK.4Parking Garage IDIlluminated Letters
LED LightingPARK.5Parking Garage IDEntrance / Exit Sign
EXIT
FREE PARKINGSATURDAY & SUNDAY
Except Event Parking
parkeparkeugene.com
PARK.7Parking GarageInformational Sign
PARK.6aParking Garage ID
Flag Mounted Sign
Front View: Hult Garage- Entrance 1SCALE: 3/8" = 1'-0"1
*Fabricator MUST verify all measurements in �eld prior to fabrication
1'-2"
14'-8 1/4" VIF 14'-8 1/4" VIF
10"
1
4
3
2
1
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
Remove existing signs: 1. Entrance/ Exit signs2. Flag mounted sign3. Exit/ Entrance Signs4. Garage Info
Re-surface garage where needed prior to installation of new signs. (Patch/Paint)
Measurements given as an estimate only. The fabricator MUST verify all measurements for signs in field prior to fabrication.
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.17
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Hult Garage Entrance 2
H U L T G A R A G EH U L T G A R A G E
ENTRANCE
PARK.4Parking Garage IDIlluminated Letters
PARK.6aParking Garage IDFlag Mounted Sign
LED Lighting
PARK.5Parking Garage ID - Entrance Sign
Front View: Hult Garage- Entrance 2SCALE: 3/8" = 1'-0"1
*Fabricator MUST verify all measurements in �eld prior to fabrication
11'-6" - VIF
2
1
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
Remove existing signs: 1. Entrance Sign2. Flag mounted sign
Re-surface garage where needed prior to installation of new signs. (Patch/Paint)
Measurements given as an estimate only. The fabricator MUST verify all measurements for signs in field prior to fabrication.
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.18
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Hult Garage Entrance 3
PARK.5Parking Garage ID - Exit Sign
EXIT
Front View: Hult Garage- Entrance 3SCALE: 3/8" = 1'-0"1
*Fabricator MUST verify all measurements in �eld prior to fabrication
12'-3" VIF
1'-2"
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.19
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Hult Garage Entrance 4
H U L T G A R A G EH U L T G A R A G E
ENTRANCE
PARK.4Parking Garage IDIlluminated Letters
PERMIT PARKING
ONLY
EXCEPT AT METERS
8am-5pmMon-Fri
parkeparkeugene.com
LED Lighting
PARK.5Parking Garage ID - Entrance Sign
PARK.7Parking GarageInformational Sign
PARK.6aParking Garage IDFlag Mounted Sign
Front View: Hult Garage- Entrance 4SCALE: 3/8" = 1'-0"1
*Fabricator MUST verify all measurements in �eld prior to fabrication
1'-2"
10'-0" VIF
1
2
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
Remove existing signs: 1. Any Banner Signs2. Post Mounted Entrance sign
Re-surface garage where needed prior to installation of new signs. (Patch/Paint)
Measurements given as an estimate only. The fabricator MUST verify all measurements for signs in field prior to fabrication.
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.20
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Overpark Entrance
CLEARANCE 7’-0” CLEARANCE 7’-0”
O V E R P A R K G A R A G EO V E R P A R K G A R A G E
ENTRANCE ENTRANCE
LED LightingPARK.5Parking Garage IDEntrance / Exit Sign
PARK.4Parking Garage IDIlluminated Letters
FREE PARKINGSATURDAY & SUNDAY
Except Event Parking
parkeparkeugene.com
PARK.6aParking Garage IDFlag Mounted Sign
PARK.7Parking GarageInformational Sign
Front View: Overpark EntranceSCALE: 1/4" = 1'-0"1
*Fabricator MUST verify all measurements in �eld prior to fabrication
1'-2"
17'-0" VIF 17'-0" VIF
Remove existing signs: 1. Flag mounted sign2. Entrance Signs
Re-surface garage where needed prior to installation of new signs. (Patch/Paint)
Measurements given as an estimate only. The fabricator MUST verify all measurements for signs in field prior to fabrication.
1
2
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.21
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Overpark Exit
LED LightingPARK.5Parking Garage IDEntrance / Exit Sign
EXIT EXIT
Front View: Overpark ExitSCALE: 1/4" = 1'-0"1
*Fabricator MUST verify all measurements in �eld prior to fabrication
17'-0" VIF 17'-0" VIF
1'-2"
Remove existing signs: 1. Exit signs
Re-surface garage where needed prior to installation of new signs. (Patch/Paint)
Measurements given as an estimate only. The fabricator MUST verify all measurements for signs in field prior to fabrication.
1 1
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.22
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Parcade Entrance 1
P A R C A D E G A R A G EP A R C A D E G A R A G E
LED Lighting
PARK.4Parking Garage IDIlluminated Letters
FREE PARKINGSATURDAY & SUNDAY
Except Event Parking
parkeparkeugene.com
PARK.7Parking GarageInformational Sign
PARK.6aParking Garage IDFlag Mounted Sign
ENTRANCEEXITEXIT
PARK.5Parking Garage IDEntrance / Exit Sign
Front View: Parcade EntranceSCALE: 1/4" = 1'-0"1
*Fabricator MUST verify all measurements in �eld prior to fabrication
17'-10 1/2" VIF
1'-6"
14'-7 1/2" VIF14'-7 1/2" VIF
Remove existing signs: 1. Flag Sign
Re-surface garage where needed prior to installation of new signs. (Patch/Paint)
Measurements given as an estimate only. The fabricator MUST verify all measurements for signs in field prior to fabrication.
1
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.23
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Parcade Entrance 2
PARK.4Parking Garage IDIlluminated Letters
PARK.7Parking GarageInformational Sign
FREE PARKINGSATURDAY & SUNDAY
Except Event Parking
parkeparkeugene.com
ENTRANCE
LED Lighting
PARK.5Parking Garage IDEntrance / Exit Sign
PARK.6aParking Garage IDFlag Mounted Sign
P A R C A D EP A R C A D E
Front View: Parcade Entrance 2SCALE: 1/4" = 1'-0"1
*Fabricator MUST verify all measurements in �eld prior to fabrication
1'-6"
1'-2"
16'-10" VIF
Remove existing signs: 1. Garage Name Letters2. Flag mounted sign
Re-surface garage where needed prior to installation of new signs. (Patch/Paint)
Measurements given as an estimate only. The fabricator MUST verify all measurements for signs in field prior to fabrication.
1
2
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
D.24
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Pearl Garage Entrance
PARK.5Parking Garage IDEntrance / Exit Sign
ENTRANCEEXIT
LED Lighting
PARK.4Parking Garage IDIlluminated Letters
P E A R L S T R E E T G A R A G EP E A R L S T R E E T G A R A G E
PERMIT PARKING
ONLY
EXCEPT AT METERS
8am-5pmMon-Fri
parkeparkeugene.com
PARK.7Parking Garage
Informational Sign
PARK.6Parking Garage IDFlag Mounted Sign
*Fabricator MUST verify all measurements in �eld prior to fabrication
Front View: Pearl GarageSCALE: 3/8" = 1'-0"1
1'-2"
12'-7" VIF 12'-7" VIF
Remove existing signs: 1. Flag Mounted Sign
Re-surface garage where needed prior to installation of new signs. (Patch/Paint)
Measurements given as an estimate only. The fabricator MUST verify all measurements for signs in field prior to fabrication.
1
MunicipalCourt Lot
HultGarage
ParcadeGarage
Federal Court Lot
BroadwayNorth
Garage
BroadwaySouth
Garage
OverparkGarage
Pearl StGarage
AmtrakLot
EXIT -3
EXITENTRY -1
ENTRY - 2ENTRY - 4
EXITENTRY -1
ENTRY -2
PublicLibrary
McDonaldTheater
ActorsCabaret
LCCDowntown
OregonContemporary
Theatre
The JazzStation
VisitorCenter
Paci�cUniversity
WOWHall
SheddInstitute
GreyhoundBus Depot
Park Blocks
DefazioPed/Bike
Bridge
Lane TransitDistrict
HultCenter
PostO�ce
CountyCourthouse
MunicipalCourthouse
FederalCourthouse
Train Depot
Shelton McMurpheyJohnson House
Garage Plan View
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.25
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type OVD.1 Overhead Vehicular
Directional
Overhead DirectionalOVD.1
PARK
YIELD
EXIT
DO NOT ENTER
NO CASH
CASH OK
CREDIT ORVALIDATIONS
Front View: OVD.1SCALE: 1/2" = 1'-0"1
Alternate LayoutsFinal Messages TBD by Client
R4 14
R5 14
R6 14
R5 141'-1 1/2" 7"
5'-10"- VIF
*Fabricator MUST verify all measurements in �eld prior to fabrication
14. SIGN PANEL - REFLECTIVE MATERIAL: 1/8" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted GRAPHIC BACKGROUND AND COPY PROCESS:
3M custom inks print direct to 3930 with 3M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications)
FASTENER: Press-roll per 3M requirements. Mechanically Fasten to Parking Garage Structure. Mounting varies per location.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.26
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type COLUMN.1 Column Wrap
Column WrapCOLUMN.1
3 3
1 345
Front View: COLUMN.1SCALE: 1/2" = 1'-0"1 Side View
Level Layouts
Side View Side View
P8 15
P1 15
*Fabricator MUST verify all measurements in �eld prior to fabrication
Width Varies per Garage"
3'-10"
15. PAINTED COLUMN Masked /Painted graphics. To follow ePark
Eugene paint standards.
NOTE: Conditions Vary per location. Fabricator to field verify prior to fabrication.
TYPICAL COLUMN SIZES Pearl St Garage: 1'-6" x 1'-6" Overpark: 1'-8" x 1'-2" Broadway N&S: 1'-0" x 2'-0" Parcade: 2'-0" x 2'-0" Hult Garage: 1'-4" dia Round Column
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.27
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type INFO.1 Information Sign
Information SignINFO.1
Front View: INFO.1SCALE: 1/2" = 1'-0"1
Graphic Layouts: INFO.1SCALE: 1" = 1'-0"2
LEVELS2,3,4
PERMITPARKING
ONLY
LEVELS2,3,4
PERMITPARKING
ONLY
PAY AT METER
CHECK
SPACE NUMBER
Final Messages TBD by Client
V1 16
P4 16
*Fabricator MUST verify all measurements in �eld priorto fabrication
2 3/4"1 3/4"
2"1 3/4"
2"2 1/4"
2"2 1/4"
2"
3"
3Elevator, Restroom
1'-5"
7"
1"1 1/4"
2 3/4" 2" 1 1/2"
11"
2'-0"
1'-6"
6 1/4"
4 1/2"3 1/2"
16. SIGN PANEL - PAINT & VINYL MATERIAL: 1/8" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
GRAPHICS (Messages, Symbols, Arrows): 3M Scotchcal Electrocut Graphic Vinyl Film, with
printed graphics. FASTENER: Mechanically fastened to column
with tamper resistant hardware.
NOTE: Conditions Vary per location. Fabricator to field verify prior to fabrication.
TYPICAL COLUMN SIZES Pearl St Garage: 1'-6" x 1'-6" Overpark: 1'-8" x 1'-2" Broadway N&S: 1'-0" x 2'-0" Parcade: 2'-0" x 2'-0" Hult Garage: 1'-4" dia Round Column
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.28
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type SPACE.1 Space Identification
Space IdentificationSPACE.1
Front View: SPACE.1SCALE: 1/2" = 1'-0"1
PERMITPARKING
ONLY7AM-6PMMON-FRI
Graphic Layouts: SPACE.1SCALE: 1 1/2" = 1'-0"2
E26611515-180
ELECTRICVEHICLE
CHARGINGONLY
RESERVEDPARKINGPERMIT
PARKINGONLY
7AM-6PMMON-FRI
RESERVEDPARKING
UNAUTHORIZED VEHICLE CITED OR TOWED AT OWNERS EXPENSE. EUGENE CODE 5.240
Final Messages TBD by Client
Changeable insert:Plastic changeable track with acrylic facew/ slot for 5”x 9” sheet of paper.
9"
5"
P1 16
V2 161'-6"
1'-0"
1'-0"
16. SIGN PANEL - PAINT & VINYL MATERIAL: 1/8" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
GRAPHICS (Messages, Symbols, Arrows): 3M Scotchcal Electrocut Graphic Vinyl Film, with
printed graphics. FASTENER: Mechanically fastened to wall/ or
column with tamper resistant hardware.
NOTE: Conditions Vary per location. Fabricator to field verify prior to fabrication.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.29
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type TEMP.1 Temporary Sign
Temporary SignTEMP.1
17. A-FRAME PRODUCT http://www.displays2go.com (or equal) Double-sided Plastic Sign Display 24" x 36" w/
Inserts and Lenses SKU#: BSWPBKCBLN Material: Plastic Color: Black Media Size: 24" x 36" Loading Style: Side Insert
A-FRAME GRAPHIC INSERT Material: 3/16" thk Coroplast or equal. Graphics: Slips into frame and is secured by
existing molded tabs.
Front View: TEMP.1SCALE: 1/2" = 1'-0"1
NORTHELEVATOR
IS OUT
parkeparkeugene.com
PLEASE USE SOUTH OR EAST ELEVATORS
NORTHELEVATOR
IS OUT
parkeparkeugene.com
PLEASE USE SOUTH OR EAST ELEVATORS
NORTHELEVATOR
IS OUT
parkeparkeugene.com
PLEASE USE SOUTH OR EAST ELEVATORS
Side View Back View
Sample Template
– 17
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.30
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type ELEVATOR.1 Elevator ID
Elevator IDELEVATOR.1
Exit to 10th AveNORTH ELEVATOR
Front View: ELEVATOR.1SCALE: 1/2" = 1'-0"1
Alternate LayoutsFinal Messages TBD by Client
*Fabricator MUST verify all measurements in �eld prior to fabrication
Exit to 8th AveSOUTH ELEVATOR
Exit to Charnelton StEAST ELEVATOR
Exit to Lincoln StWEST ELEVATOR
Paint Elevator BankWith Level Color
P4 16
V1 16
4'-0"Vaires per location
8"
16. SIGN PANEL - PAINT & VINYL MATERIAL: 1/8" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
GRAPHICS (Messages, Symbols, Arrows): 3M Scotchcal Electrocut Graphic Vinyl Film, with
printed graphics. FASTENER: Mechanically fastened to wall with
tamper resistant hardware.
NOTE: Conditions Vary per location. Fabricator to field verify prior to fabrication.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.31
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type RULES.1 Garage Rules
Garage RulesRULES.1
Front View: RULES.1SCALE: 1/2" = 1'-0"1
ATTENTION
11”x17”Insert
11”x17”Insert
ATTENTION
11”x17”Insert
11”x17”Insert
Layout Template
P4 17
V1 17
5'-0"
CL
1 1/2"4"
1'-5 1/2"
1'-5 1/2"
11"
2'-4"
17. SIGN PANEL - CHANGEABLE INSERTS MATERIAL: Fabricated Aluminum sign Frame.
Square edge profile, Non-Glare Acrylic Lens with Subsurface Digitally Printed Graphics. Room for 11"x 17" insert. Final insert Layouts TBD by client
COLOR: As specified in drawings. Mechanically fastened to wall with tamper
resistant hardware.
NOTE: Conditions Vary per location. Fabricator to field verify prior to fabrication.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.32
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type STAIR.1 Stairwell ID
Stairwell IDSTAIR.1
Front View: STAIR.1SCALE: 1/2" = 1'-0"1
EXIT
Exit to 10th AveNORTH STAIR
Exit to 8th AveSOUTH STAIR
Exit to Charnelton StEAST STAIR
Exit to Lincoln StWEST STAIR
Alternate Layout ExamplesFinal Messages TBD by Client
Paint Elevator BankWith Level Color
P4 16
V1 167"
3'-4"VIF. Varies per Location
*Fabricator MUST verify all measurements in �eld prior to fabrication
16. SIGN PANEL - PAINT & VINYL MATERIAL: 1/8" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
GRAPHICS (Messages, Symbols, Arrows): 3M Scotchcal Electrocut Graphic Vinyl Film, with
printed graphics. FASTENER: Mechanically fastened to wall with
tamper resistant hardware.
NOTE: Conditions Vary per location. Fabricator to field verify prior to fabrication.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.33
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type STAIR.2 Stairwell ID
Stairwell IDSTAIR.2
3NORTH STAIRExit to 10th Ave
Front View: STAIR.1SCALE: 1/2" = 1'-0"1
1NORTH STAIRExit to 10th Ave
2NORTH STAIRExit to 10th Ave
3NORTH STAIRExit to 10th Ave
4NORTH STAIRExit to 10th Ave
5NORTH STAIRExit to 10th Ave
Level Layouts
P10P6 P7 P8 P9
1'-5"
7"
P8 16
P1 16
P4 16V1 16
2'-0"
1'-6"
10 1/2"
1"1 3/4"1"1"1 1/4"
16. SIGN PANEL - PAINT & VINYL MATERIAL: 1/8" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
GRAPHICS (Messages, Symbols, Arrows): 3M Scotchcal Electrocut Graphic Vinyl Film, with
printed graphics. FASTENER: Mechanically fastened to wall or
column with tamper resistant hardware.
NOTE: Conditions Vary per location. Fabricator to field verify prior to fabrication.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.34
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type METER1&2 PARking Meter Info
Parking Meter InfoMETER.1&2
Front View: METER.1 & 2SCALE: 1/2" = 1'-0"1
RATES
PAYHERE
Graphic Layout
Final Layout TBD
PAYHERE
BROADWAY SOUTH
$1.00 per hour$6.00 per daySaturday & Sunday Free
Except posted event parking, New Years Day, Martin Luther King Jr. Day, President’s Day, Memorial Day, July 4th, Labor Day, Veterans Day, Thanksgiving Day & Christmas Day.
Failure to pay is a violation of Municipal Code 5.240 and 5.285 and is subject to citation and/ or impoundment.
Monday through Friday, 7am -6pm
Garage SecuritySeguridad del Garaje541-682-8200
parkeparkeugene.com541-682-5729
Cash, Credit, Permit, Park Mobile
3 1/4"1 1/2"3 1/4"
P4 16
V1 161'-6"
1'-6"
1'-6"
2'-3"
2'-3"
16. SIGN PANEL - PAINT & VINYL MATERIAL: 1/8" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth COLOR: custom, as noted SURFACE PROCESS: Paint all exposed surfaces
with Matthews Acrylic Polyurethane, with clear coat satin finish.
GRAPHICS (Messages, Symbols, Arrows): 3M Scotchcal Electrocut Graphic Vinyl Film, with
printed graphics. FASTENER: Mechanically fastened to wall or
column with tamper resistant hardware.
NOTE: Conditions Vary per location. Fabricator to field verify prior to fabrication.
SPECIFICATIONS SIGN TYPE: FUNCTION:
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
SUBCONSULTANT
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be noti-fied of any variations from the dimensions and condi-tions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH7-5-17
9-21-17
D.35
NOTES
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a licensed engineer in the
State of the project.
Sign Type BOOTH.1 Parking Booth
Parking BoothBOOTH.1
43"
41"
6"2"
12"
1" DRIPANGLE(TYP)
146" O.A.
10"
51 716 " O.A.
24"3"
32"2"
36"2"
34" 3"
136"
48"
80"
ATTIC VENT(4 PLACES)
REMOVABLELIFTING EYE(4 PLACES)
105" O.A.
IN-WALL SLIDINGWINDOW
SLIDING DOOR w/FIXED WINDOW
Left View: BOOTH.1SCALE: 1/2" = 1'-0"1 Front View: BOOTH.1
SCALE: 1/2" = 1'-0"2
P5
P5
17. PAINT Paint parking pay booths. Refernce drawing &
color chart for specifications. (Booths by others, drawing provided for reference only)
Graphic LayoutsE
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
E.1
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
PARK.2, PARK.2aLayout Drawings
SIGN PANEL LAYOUTS: NOTES:• Refer to message schedule for actual sign messages.
• Panel layouts for ALL sign locations shall be included in shop drawings for review by designer and client.
Hult CenterParking
NEXT LEFT
ParcadeGarage
Hult CtrParking
OverparkGarage
Pearl StGarage
8th Ave Lot
PUBLICPARKING
8th Ave Lot
PUBLICPARKING
Hult CenterParking
Hult CenterParking
BroadwayGarage
S N
ParcadeGarage
RIGHT LANE
Hult CenterParking
BroadwayGarage
N S
Graphic Layouts: PARK.2-2aSCALE: 3/4" = 1'-0"2
LOC 400 LOC 400a
LOC 402LOC 408LOC 413 LOC 413a
LOC 408a
LOC 403 LOC 403b
LOC 404 LOC 405a
2'-3"
1'-4"
1'-10"
3 1/2"3"
1 1/2"3"
4"
3"
Ø 1'-0"
Ø 10 1/2"
3 3/4"
3 1/2"
1'-0 1/2"
1'-0 1/2"
2 3/4"3"
1 1/2"3"
2 1/4"2 3/4"
2"3 1/2"
1'-1"
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
E.2
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
PARK.3 Layout Drawings
SIGN PANEL LAYOUTS: NOTES:• Refer to message schedule for actual sign messages.
• Panel layouts for ALL sign locations shall be included in shop drawings for review by designer and client.
MunicipalCourt Lot
PUBLICPARKING
EugeneTrainDepot
PUBLICPARKING
Graphic Layouts: PARK.3SCALE: 3/4" = 1'-0"1
LOC 411 LOC 425
2'-3"
2'-0 1/2"
Ø 1'-3"Ø 1'-1 1/4"
1'-8"
5'-3"
8"
4"
2 3/4"
4"
3 1/2"
3 1/2"3"
1 3/4"
Construction DetailsF
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
F.1
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Construction Details
Sign Type: PARK.1PARK.1bPARK.2PARK.3
PARK.1-3 Section Details
3/16" thick Aluminum Bracket, spot weld to back of sign panel
1/4" thick Aluminum Sheet
4" x 4" x .25" wall Aluminum Square Tube
Section: PARK.1, PARK.2SCALE: 3" = 1’ -0"1
Section: PARK.3SCALE: 3" = 1’ -0"2
1/4" thick Aluminum Sheet
4" x 4" x .25" wall Aluminum Square Tube
Section: PARK.1bSCALE: 3" = 1’ -0"3
1/4" thick Aluminum Sheet1" Aluminum reverse channel letter (P-Symbol)
1/4" thick fabricated Aluminum Sign Cabinet
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
F.2
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Transpo Break-Safe
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
F.3
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Foundation Details
Construction Details
Sign Type: GATE.1
Sidewalk Footer Placement Details
The FABRICATOR shall be familiar with all site conditions and shall be responsible for all underground utility checks.
The FABRICATOR shall be familiar with all basement/vault locations by obtaining plans from the local municipality Department of Public Works.
Where a basement/vault interferes with a proposed location, the sign shall be relocated to a location deemed appropriate by the municipalities Department of Public Works
Where relocation is not an option the FABRICATOR will develop the appropriate mounting solution. The solution shall meet all engineering criteria as established by the standard footings (i.e. windloads).
FINAL DESIGNS AND SHOP DRAWINGS SHALL BE SUPPLIED BY THE FABRICATOR FOR EACH OF THE BREAK-AWAY POLES IDENTIFIED AND AN OREGON REGISTERED PROFESSIONAL ENGINEER IS REQUIRED TO SIGN AND SEAL THE SUBMITTAL OF SHOP DRAWINGS.
NOTE: 1) SOIL IS AVERAGE WITH MAXIMUM ALLOWABLE
SOIL PRESSURE OF 3,000 POUNDS PER SQUARE FOOT. SOIL UNIT WEIGHT OF 125 PCF AND FRICTION ANGLE OF 30 DEGREES (ASSUMED).
2) CONCRETE STRENGTH AT 28 DAYS F’C=4,000 PSI REINFORCEMENT SHALL BE ASTM 36 FY=60,000 PSI
3) FOLLOW 2009 ODOT DESIGN STANDARDS FOR MATERIAL AND CONSTRUCTION INFORMATION FOR THE SIGN POST BASES AND FOUNDATIONS NOT OTHERWISE SPECIFIED IN THESE CONTRACT DRAWINGS.
4) FOR SIGN POST SIZES REFER TO THE DESIGN INTENT DRAWING SHEETS.3'-0" Minimum
3'-0"
Min
imum
5" s
idew
alks
7" d
rivew
ays
3'-0" square
2'-0"
5" s
idew
alks
7" d
rivew
ays
4'-0" square
1'-1"
5" s
idew
alks
7" d
rivew
ays
3'-0" Minimum
3'-0"
Min
imum
4"
Section View: Foundation @ PaversSCALE: 3/4" = 1'-0"2
Existing Pavers
Section View: Foundation @ ConcreteSCALE: 3/4" = 1'-0"1
Existing Concrete Slab
Transpo® AS4 Break-SafeBreak Away Sign Support
Class B Concrete FootingReference ODOT
4” x 4” Rectangle Aluminum Post
Transpo® AS4 Break-SafeBreak Away Sign Support
4” x 4” Rectangle Aluminum Post
Transpo® AS4 Break-SafeBreak Away Sign Support
4” x 4” Rectangle Aluminum Post
Transpo® AS4 Break-SafeBreak Away Sign Support
4” x 4” Rectangle Aluminum Post Note: Design Wind load 300 PSF 120 MPH,3 Sec Gust Wind, Exp C
Note: Design Wind load 300 PSF 120 MPH,3 Sec Gust Wind, Exp C
Note: Design Wind load 300 PSF 120 MPH,3 Sec Gust Wind, Exp C
Note: Design Wind load 300 PSF 120 MPH,3 Sec Gust Wind, Exp C
Class B Concrete FootingReference ODOT
Section View: Foundation: Shallow DepthSCALE: 3/4" = 1'-0"3
Existing Concrete Slab
Class B Concrete FootingReference ODOT Section View: Foundation: Extremely Shallow Depth
SCALE: 3/4" = 1'-0"4
Existing Concrete Slab
Class B Concrete FootingReference ODOT
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
F.4
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Plate-to-PlateFooter Detail
Below Grade
Below Grade
Section: Bolt w/ Nut Plate-to-Plate MOUNTINGBrick Pavers SurfaceSCALE: 1" = 1' - 0"2
Section: Bolt w/ Nut Plate-to-Plate MOUNTINGConcrete Pavement SurfaceSCALE: 1" = 1' - 0"1
Weep Holes as Required
Aluminum Post(Size varies by sign type)
Leveling Nuts
1/2" thk Aluminum Plates
6" Crushed Stone
3" Base Concrete Slab
5" SmoothConcrete Pad
Typ. vertical rebar as required
6" Crushed Stone
2–3" Bitum. Setting Bed
Poured in Place Concrete Footer4,000 psi @ 28 Days
1" DIA Steel Bolts w/ Hex Head nut at bottom
Compacted Crushed Stone as Required
Provide weather seal sand &gravel @ footing
5"3'
-0"
min
.
Sonotube Size Varies by Sign TypeEngineer to determine size.
Weep Holes as Required
Aluminum Post(Size varies by sign type)
Leveling Nuts
1/2" thk Aluminum Plates
5" Brick Pavers
Typ. vertical rebar as required
Poured in Place Concrete Footer4,000 psi @ 28 Days
1" DIA Steel Bolts w/ Hex Head nut at bottom
Compacted Crushed Stone as Required
Provide weather seal sand &gravel @ footing
5"3'
-0"
min
.
Sonotube Size Varies by Sign TypeEngineer to determine size.
The FABRICATOR shall be familiar with all site conditions and shall be responsible for all underground utility checks.
The FABRICATOR shall be familiar with all basement/vault locations by obtaining plans from the local municipality Department of Public Works.
Where a basement/vault interferes with a proposed location, the sign shall be relocated to a location deemed appropriate by the municipalities Department of Public Works
Where relocation is not an option the FABRICATOR will develop the appropriate mounting solution. The solution shall meet all engineering criteria as established by the standard footings (i.e. windloads).
FINAL DESIGNS AND SHOP DRAWINGS SHALL BE SUPPLIED BY THE FABRICATOR FOR EACH OF THE BREAK-AWAY POLES IDENTIFIED AND AN OREGON REGISTERED PROFESSIONAL ENGINEER IS REQUIRED TO SIGN AND SEAL THE SUBMITTAL OF SHOP DRAWINGS.
NOTE: 1) SOIL IS AVERAGE WITH MAXIMUM ALLOWABLE
SOIL PRESSURE OF 3,000 POUNDS PER SQUARE FOOT. SOIL UNIT WEIGHT OF 125 PCF AND FRICTION ANGLE OF 30 DEGREES (ASSUMED).
2) CONCRETE STRENGTH AT 28 DAYS F’C=4,000 PSI REINFORCEMENT SHALL BE ASTM 36 FY=60,000 PSI
3) FOLLOW THE MOST RECENT ODOT DESIGN STANDARDS FOR MATERIAL AND CONSTRUCTION INFORMATION FOR THE SIGN POST BASES AND FOUNDATIONS NOT OTHERWISE SPECIFIED IN THESE CONTRACT DRAWINGS.
4) FOR SIGN POST SIZES REFER TO THE DESIGN INTENT DRAWING SHEETS.
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
F.5
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Sidewalk FooterPlacement Details
Sidewalk Footer Placement Details
The FABRICATOR shall be familiar with all site conditions and shall be responsible for all underground utility checks.
The FABRICATOR shall be familiar with all basement/vault locations by obtaining plans from the local municipality Department of Public Works.
Where a basement/vault interferes with a proposed location, the sign shall be relocated to a location deemed appropriate by the municipalities Department of Public Works
Where relocation is not an option the FABRICATOR will develop the appropriate mounting solution. The solution shall meet all engineering criteria as established by the standard footings (i.e. windloads).
FINAL DESIGNS AND SHOP DRAWINGS SHALL BE SUPPLIED BY THE FABRICATOR FOR EACH OF THE BREAK-AWAY POLES IDENTIFIED AND AN OREGON REGISTERED PROFESSIONAL ENGINEER IS REQUIRED TO SIGN AND SEAL THE SUBMITTAL OF SHOP DRAWINGS.
NOTE: 1) SOIL IS AVERAGE WITH MAXIMUM ALLOWABLE
SOIL PRESSURE OF 3,000 POUNDS PER SQUARE FOOT. SOIL UNIT WEIGHT OF 125 PCF AND FRICTION ANGLE OF 30 DEGREES (ASSUMED).
2) CONCRETE STRENGTH AT 28 DAYS F’C=4,000 PSI REINFORCEMENT SHALL BE ASTM 36 FY=60,000 PSI
3) FOLLOW THE LATEST ODOT DESIGN STANDARDS FOR MATERIAL AND CONSTRUCTION INFORMATION FOR THE SIGN POST BASES AND FOUNDATIONS NOT OTHERWISE SPECIFIED IN THESE CONTRACT DRAWINGS.
4) FOR SIGN POST SIZES REFER TO THE DESIGN INTENT DRAWING SHEETS.
Plan: Footer PlacementSCALE: NTS1
Plan View: Footer SCALE: 1" = 1' - 0"2
NOTE: When locating a footer within a single pavement block adjacent to at least 2 expansion joints, the entire block of pavementshall be removed and replaced with the same materials and finish of adjacent sidewalk areas.
Plan: Specialty Pavers Footer PlacementSCALE: NTS3
Unacceptable Footer Detail
Unacceptable Footer Detail
Unacceptable Footer Detail
NOTE: The pattern of bricks need to be removed, stored and replacedin the order they were removed. Marking the Specialty Pavers sidewalk with spray paint will NOT be allowed.
Acceptable Footer Detail
Acceptable Footer Detail
Acceptable Footer Detail
Vari
es
Varies
Footer
Class BConcrete FootingReference State DOTReq. Standards
Break-Away System
Sign Post
Existing sidewalk blockto be removed and replaced
Footer
Sign Post
Existing Specialty Paversto be removed, saved and replaced.
CL
C L
Sign Post
REVISIONS
CLIENT / PROJECT
SHEET TITLE
DATE
PROJECT NO.
DRAWN BY:
SHEET NO.
These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions shown on this drawing. Shop drawings and details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department.
LH
7-5-17
9-21-17
F.6
SPECIFICATIONS
City of Eugene Wayfinding and Signage System
Parking
120 North Church StreetSuite 208West Chester, PA 19380T 484.266.0648www.merjedesign.com
E N V I R O N M E N T S & E X P E R I E N C E S
NOTES:1. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting
situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.
2. All vinyl and painted surfaces must receive a compatible anti-graffiti (and U/V) clear coat or vinyl over laminate.
3. Hardware: All exposed hardware shall be tamper proof fasteners.4. Contractor must provide shop drawings for all structural components, signed and sealed by a
licensed engineer in the State of the project.
Bitro Group Resno Face-Lit Letters