kasipkor.kzkasipkor.kz/wp-content/uploads/2016/09/43-electrical-equipment-o… · web...

Ministry of Education and Science of the Republic of KazakhstanNon-commercial Joint stock Company «Holding «Kasipkor»

EDUCATIONAL PROGRAM on the specialty: 0901000 Electrical equipment of electrical

power station and networks

Qualifications:

0901022 Electrician on repair of electrical equipment for power stations* (3 level of NQF)

0901043 Electrical technician (4 level of NQF) ***** Junior electrical engineer (5 level of NQF)

Astana – 2015

1

CONTENT Introduction 31 Curriculum 42 Explanatory note to structure and content 93 Structure and content of educational program 144 List of equipment 395 List of literature 61

2

INTRODUCTION

This educational program is based on the competence approach, taking into account modern international requirements for mid-level specialists and skilled workers, with the participation of foreign partner LD DIDACTIC Group (Federal Republic of Germany).

The educational program is based on competencies, designed with the concept of lifelong learning, as the content of educational programs aimed at the formation of highly qualified specialists, capable of adapting to changing situations at work, on the one hand, and to continue professional development and education, on the other.

This approach to training allows to create a feeling of success of each student, which is created by the organization of educational process in which the learner can and should take over control of own learning, which teaches him to take responsibility for own learning, and in the future – for own professional growth and career . Thus, student as a consumer will be satisfied with education; he/she can improve it for life, responding to changes in labor market.

The educational program on the specialty contains information on the relevant levels of qualification, professional profile, curriculum, the requirements for applicants and the implementation of vocational training. This takes into account the requirements for competences of qualification levels 3, 4 and 5 of the National Qualifications Framework of the Republic of Kazakhstan.

The educational program on a specialty «Electrical equipment of electrical power station and networks» designed to meet basic provisions of:

Law of the Republic of Kazakhstan «About Education» dated July 27, 2007; State Program for Education Development of the Republic of Kazakhstan

for 2011-2011 years (Presidential Decree dated December 7, 2010 №1118); Development Strategy of NC JSC «Holding «Kasipkor» for 2012-2021 years

(DGRK dated December 31, 2011 №1751); State program on industrial-innovative development of the Republic of

Kazakhstan for 2015-2019 years (Presidential Decree dated March 19, 2010 № 957);

National Qualifications Framework of the Republic of Kazakhstan (joint order of Minister of Labour and Social Protection of the Republic of Kazakhstan dated 24 September 2012 №373, and Minister of Education and Science of the Republic of Kazakhstan dated 28 September 2012 №444).

It provides an opportunity to assign such qualifications as «0901022 Electrician on repair of electrical equipment for power stations*», «0901043 Electrical technician» and «******* Junior electrical engineer».

To implement this program in the practice of the institution, institution needs to develop working curricula and programs depending on the features of labor market in region and requirements of customer-employer.

3

CURRICULUM

Specialty: 0901000 Electrical equipment of electrical power station and networks Qualifications: 0901022 Electrician on repair of electrical equipment for

power stations* 0901043 Electrical technician ***** Junior electrical engineer

Study form: full-timeDuration of study: 3 years 6 months

on the basis of: general secondary education№ Study cycles and study disciplines (modules) Forms of control The volume of training (hour)

exam

inat

ion

pass

Num

ber

of q

uizz

es

Cou

rse

wor

k (p

roje

ct)

Tota

l (in

hou

rs)

Including: Distribution by

semesters

theo

retic

al le

sson

s

prac

tical

exe

rcis

es

(labo

rato

ry a

nd

cour

se w

ork

(pro

ject

)

1 2 3 4 5 6 7 8 91 Humanitarian basic module (professional

Kazakh/Russian, professional English, history of Kazakhstan, physical culture)

300 70 230 1-4

2 Basic professional modules 420 140 280 1-22.1 Analyzing electrical systems and checking

functionsE 1 90 40 50 1-2

4

2.2 Planning and executing electrical installations E 1 90 40 50 1-2

2.3 Providing information technology systems + 1 80 20 60 1-22.4 Ensuring electric energy supply and safety of

equipmentE 2 100 20 80 1-2

2.5 Operational and technical communication + 1 60 20 40 1-2

3 Basic special modules 240 40 192 8 1-2

3.1 Manufacturing and checking electrical machines + 1 80 20 60 1-23.2 Installing and removing electrical machinery E 1 1 80 0 72 8 1-23.3 Establishing and maintaining energy-related

systems+ 1 80 20 60 1-2

4 Disciplines, defined by educational organization

72 32 40 1-2

5 Industrial training and professional practice 400 1-25.1 Industrial training + 230 25.2 Professional practice + 170 26 Interim examination 87 Socio-economic module (foundations of

philosophy, economics, law and cultural studies)180 110 70 3-4

8 Professional modules 280 70 210 3-48.1 Planning and executing electrical installations E 1 90 20 70 3-48.2 Analyzing, programming and realizing controls

for systemsE 1 120 20 100 3-4

8.3 Operational and technical communication + 70 30 40 3-49 Special modules 460 100 344 16 3-4

9.1 Installing and maintaining propulsion systems E 1 120 40 80 3-49.2 Running and commissioning operating building

services systems+ 1 60 20 40 3-4

9.3 Establishing and maintaining energy-related systems

+ 1 60 20 40 3-4

9.4. Installing and commissioning of electrical equipment

+ 1 100 20 80 3-4

5

9.5 Configuring and programming of control systems E 1 1 120 0 104 16 3-410 Disciplines, defined by educational

organization 72 32 40 3-4

11 Industrial training and professional practice 368 411.1 Industrial training + 222 411.2 Professional practice + 146 412 Interim examination

(level 4, 5)8

13 Final examination (level 3)

72

13.1 Examination at educational organization on the basis of a full course of study

60

13.2 Assessment of the level of professional preparedness and qualification assignment

12

14 Total for compulsory education (1 year 10 months)

2880

15 Humanitarian module (professional Kazakh/Russian, professional English, history of Kazakhstan, physical culture)

180 90 90 5-6

16 Advanced professional modules 200 80 120 5-616.1 Planning, implementing and maintaining

electrical systemsE 1 120 40 80 5-6

16.2 Analysis of technical order, solution development E + 1 80 40 40 5-617 Advanced special modules 480 140 340 5-6

17.1 Technical service and operation + 1 40 20 20 5-617.2 Commissioning and maintaining automated

systemsE 1 120 40 80 5-6

17.3 Measuring and analyzing electrical functions and systems

+ 1 80 20 60 5-6

17.4 Installing and commissioning of electrical equipment

E 1 120 40 80 5-6

17.5 Maintaining equipment and systems + 1 120 20 100 5-618 Disciplines, defined by educational 72 32 40 5-6

6

organization 19 Industrial training and professional practice 428 6

19.1 Industrial training + 172 5-619.2 Professional practice + 256 6

19.2.1 Technological practice + 160 619.2.2 Engineering project + 96 6

20 Interim examination (level 5) 821 Final examination

(level 4)72


60


12

22 Total for compulsory education (2 years 10 months)

4320

23 Special advanced modules 380 160 220 723.1 Configuring and programming of control systems E 1 140 40 100 723.2 Commissioning and maintaining automated

systemsE 1 120 40 80 7

23.3 Business processes and quality management + 2 120 80 40 724 Industrial training and professional practice 412 7

24.1 Industrial training + 212 724.2 Professional practice + 200 7

24.2.1 Pre-diploma practice + 80 724.2.2 Diploma project + 120 7

25 Final examination (level 5)

72


60


12

26 Total for compulsory education (3 years 6 5184

7

months)27 Consultation Not more than 100 hours for an academic year 28 Extracurricular activities Not more than 4 hours per week during a theoretical training 29 Total 14 25 27 2 5800 1096 4064 24

8

EXPLANATORY NOTE to structure and content of educational program by specialty

0901000 «Electrical Equipment of Electrical Power Stations and Networks»

Curriculum and training program consist of various modules. The term «module» explains the model of «learning areas» that are taught in a combination of theoretical and practical units. Thus, each module is focused on the exploration and development of competences provided for in the framework of preparation for the profession. Thus, each module is focused on the mastering and development of competences provided in the framework of preparation for the specialty.

Curriculum by specialty «Electrical Equipment of Electrical Power Stations and Networks» is divided into several cycles of educational course:

Humanitarian basic module Basic professional modules Basic special modules Disciplines defined by the educational organization Socio-economic module Professional modules Special modules Advanced professional modules Advanced special modules Special advanced modules Industrial training and professional practice. The content of the above mentioned modules varies according to the level of

expertise that is to be achieved (see Pic.1).

Pic.1. Qualification levels by specialty «Electrical Equipment of Electrical Power Stations and Networks»

9

There is an opportunity to proceed from level 3 to level 5 in the curriculum by specialty «Electrical Equipment of Electrical Power Stations and Networks» according to National qualifications framework of RK (see Pic.1).

Student can reach level 3 «Electrician on Repair of Electrical Equipment for Power Stations» and be employed. If student wants to proceed by the specialty, he/she will study another 8 months to reach level 4 «Electrical Technician». Then student can continue study another 8 months to reach level 5 «Junior Electrical Engineer».

1) «Electrician on Repair of Electrical Equipment for Power Stations» (Level 3)

Sign off electrical equipment Record and catalogue machine and winding data Set up and clear away workplaces Assemble and dismantle electrical machines Assemble and wire switch cabinets, including measurement and control

equipment, assemble drive systems Install and set up machines and drive systems, including pneumatic

components Assemble and wire up switchgear and automation systems Maintain and monitor electrical machines and drive systems in operational

use Work with English language documentation and communicate in English Under the provisions of the Prevention of Accidents Regulations,

electronics technicians for industrial engineering are deemed to be skilled electrical and electronic engineering workers.

2) «Electrical Technician» (Level 4)

Sign off electrical equipment Design equipment modifications and expansions Set up and clear away workplaces/building sites Organize plant assembly Monitor the work of service providers and other trades Assemble and install wiring systems, information cables and power lines,

including general supply lines Install and set up machines and drive systems, including

pneumatic/hydraulic components Assemble and wire up switchgear and automation systems Program and configure systems, test the functionality and safety facilities

of systems10

Monitor and maintain plants, carry out checks on a regular basis Analyze faults, initiate immediate measures and carry out routine repairs

to plants Hand over plants, instruct users in their operation and provide services Work with English language documentation and communicate in English Under the provisions of the Prevention of Accidents Regulations,

electronics technicians for industrial engineering are deemed to be skilled electrical and electronic engineering workers.

3) «Junior Electrical Engineer» (Level 5)

There is the possibility for examined learners in level 4 to achieve level 5 “Junior electrical engineer” by passing additional courses and exams. Then they gain special competences in:

Planning and organizing work of teams, also in hazardous situations Evaluating results of work Maintain and monitor automated systems and programming of control

systems Organizing business processes and quality management Advising and supporting customersDuration of study by the educational program of TVET at full-time training

on the basis of upper secondary education (accredited/ certified) is: Level 3: 1 year 10 months Level 4: 2 years and 10 months Level 5: 3 years 6 months

The Organization of Industrial Training and Professional Practice include:

Training and industrial work on the acquisition of skills (industrial training in training labs and workshops);

Training and industrial work on the acquisition and development of skills (industrial training in training labs and workshops, professional practice and training at production);

Professional practice (technological, pre diploma).The duration of each type of practice is determined in accordance with the

requirements of the qualification profile of the specialist with the respective qualification (e.g. “Electrical Technician”).

Terms and contents of professional practice are defined by working qualification characteristics of specialists with the qualification “Electrical Technician”.

Industrial training is carried out in training workshops under the guidance of qualified and experienced instructors. It is provided for learners to master a

11

number of related work qualifications with the assignment of grades during the period of practice.

Professional practice is carried out in the relevant organizations, at workplaces provided by employers, and it is aimed at consolidating knowledge acquired during training of both practical skills and professional competences. For the qualification “Electrical technician”, it should take place in the second semester of the third year of training, preferably in places where conditions and admissions of work are established (Thermal power plants, cogeneration plants, boiler). There should be responsible “experienced personnel” to supervise and instruct students according to the curriculum. Details of the organization of professional practice should be part of the contract between company, training institution and trainee. Employers’ companies independently establish the requirements for enrolment of specialists for professional practice considering overall average score for core subjects.

The interim examinations will be conducted at the end of the year of training. The number of interim examinations depend on the level of qualification (e.g. there are three interim examinations for qualification level 5, one after the first year, one after the second year and one after the third year).

The duration of an interim examination is 8 hours and has to be a written one.

The interim examinations can be divided into two parts. The first part reflects the contents of the modules of the respective year of training. The other part reflects tasks and assignments related to the corresponding level of training (level 3, 4 or 5)

The respective content of an interim examination is guided by the content of the modules students took in that year. In addition, tasks and assignments have to be determined in a way that reflects the corresponding level of the vocational training (level 3, 4 or 5).

The duration of the final examination is 72 hours. The final examination takes part at the end of training and consists of two parts: Examination at organization on the basis of a full course of study (60 hours) Assessment of the level of professional preparedness and qualification

assignment (12 hours)The final examination has to include a practical assignment, where the

examinee has to perform practical tasks as well to prove skill acquisition. A written and oral examination is also a compulsory part of the final examination.

Subject of the final examination are the skills, knowledge and competences acquired during training.

The tasks and assignments for the final examination have to be determined in a way, that most relevant modules related to the respective level are chosen to be examined.

12

CONTENT AND STRUCTURE OF EDUCATIONAL PROGRAM

Name of cycles and study disciplines (modules)

Knowledge competences and abilities formed

2 Basic professional modulesName of discipline (module):2.1 Analysing electrical systems and checking functions

ContentsOrganizational structure, work organization, operational communications Products, services Wiring diagrams, graphical symbols Electrical equipment, basic circuits, electrical basic sizes Behaviour and characteristics of exemplary components and functional units Dangers of electrical current, safety regulations, occupational health and safety Measurement methods, operational check, troubleshooting Methods of circuit analysisAnalogue and digital assembly groupsStandard solutions for circuitryMethods of fault localizationSimulation softwareMeasuring and testing proceduresTest regulations, test protocolsTechnical circuitry documentation

Competences: Analysing electrical systems and checking

functions Measuring and analysing electrical functions

and systems Determining the function and operating

behaviour of components and assembly groups in electrotechnical systems.

Systematic localization of faults and resolution of simple malfunctions

Communicating and working in teams Helping to avoid operational environmental

impact in professional sphere of influence Taking steps to protect safety and health in

the workplace

Knowledge: Explanation of tasks, work requests,

activities and exemplary work processes of the profession

Explanation of safety rules Characterizing general principles of electrical

engineering Measuring, evaluating, and calculating

electrical parameters Describing wiring diagrams, graphical

symbols Explanation of measurement methods,

troubleshooting Describing electrical systems Naming features and performance of

components and assemblies Describing first aid for accidents and

accidents involving electric current

Abilities: Analysing electro technical systems on levels

of facilities, equipment, assemblies and components

Determining function and performance of selected components and assemblies

Checking the operation of electrical circuits and equipment.

Following signals and testing interfaces14

Identifying electrical sizes Analysing and troubleshooting Scheduling time and work Selecting measuring processes and measuring

devices Applying professional occupational safety

and accident prevention regulations Avoiding waste, using materials and supplies

from an environmentally friendly sourceName of discipline (module):2.2 Planning and executing electrical installations I

Contents:Job scheduling, order realization Energy requirements of a system or a device Safety regulations Electromagnetic compatibilityInstallation technology Key parameters of equipment Types of wiring diagrams Performance dimensioning Labour organization Cost calculation, quoting

Competences: Planning and executing electrical

installations Using CAD-software for planning and

calculation of materials Determining conduction lines and device

assembly locations while taking electromagnetic compatibility into account

Installing and connecting electrical equipment

Knowledge: Job scheduling, order realization Energy needs, performance dimensioning Cost calculation, quoting Describing installation technology Safety regulations, accident prevention

regulations, safety rules

Skills: Analysing orders for installation of energy

supply Planning installations of typical network

systems Creating circuit diagrams and information

plans Planning of typical processes for the

construction of systems Construction of systems Logging of operational values and creating

documentation Checking correct operation of equipment

Name of discipline (module):2.3 Providing information technology systems

Contents:Hardware and operating systems as well as standard and application-specific softwareInstallation and configuration processes for hardware and software components

Competences: Planning for the provision and expansion of

information systems as required Selecting hardware and software components

while taking function, performance, area of application, compatibility, economy, and environmental sustainability into account

Installing and configuring information systems as well as task-related standard

15

Ergonomic workplace layoutTools and methods for diagnosing and resolving malfunctionsLocal and global networks, data transmission protocolsData backup and data protection, copyright and media lawPresentation techniques and methods

software and application-specific software Setting up an ergonomic computer

workstation and setting up the graphic user interface

Using tools and test programs Independently diagnosing simple

malfunctions in information systems and resolving these malfunctions

Knowledge: Describing hardware components and their

applications Describing the requirements of occupation-

specific software and the corresponding hardware requirements

Explaining how to comply with legal regulations governing data protection, copyright, and media law

Knowing about research options available through national and international occupational media through the use of networks

Evaluating the usefulness of tools and test programs for diagnosis

Knowing the requirements for setting up an ergonomic workstation

Skills: Using installation routines to install operating

systems and user software Connecting information technology

workstations to networks Using tools and methods to resolve

malfunctions Planning and implementing measures to back

up data and protect it Processing documentation with or without

application-specific software Presenting planning and work results using

software for word processing, table generation, graphic depictions, and presentation

Name of discipline (module):2.4 Ensuring electric energy supply and safety of equipment

Contents:Circuit and distribution systemsEnvironmental sustainabilityVoltage levels

Competences: Planning electric supply for equipment and

systems Dimensioning systems while taking network

systems and safety measures into account Testing and evaluating protective and

potential equalization conductors Evaluating the effectiveness of measures

16

Alternating current and three-phase current systemNetwork systemsSafety equipmentMeasuring and testing equipmentTest protocolsProtection ratings, insulation ratingsProtection typesUser instructions

countering electric shock when a malfunction occurs, particularly those malfunctions caused by turning off overload protection and fault current protection units

Testing and starting up stationary and mobile electrical equipment

Knowledge Analysing and classifying electric supply

options in regard to functional, financial, and ecological aspects

Describing the typical setup of circuit and distribution systems on the different voltage levels

Describing protection types for electric devices or systems in regard to environmental conditions and additional factors to consider for special types of spaces

Describing the importance of complying with norms, requirements, and regulations for protecting against electric shock, for occupational safety and for accident prevention

Skills: Using the appropriate measuring and testing

equipment for the respective test Measuring and evaluating insulation

resistance Recording and documenting performance

data and test results for electric equipment Following user instructions for the use of

circuit and distribution systems and proper use of electric equipment

Name of discipline (module):2.5 Operational and technical communication I

Contents:Basics (geometry, preferred numbers, scales, drawing sheets, fonts)Drawing standards (projections, line types, depiction in drawings, measure entries)Electrical engineering (symbols, circuit symbols, circuit diagrams)Sources of informationTeamworkDocumentationHandbooksOperation and instruction manuals

Competences: Putting together, supplementing, evaluating,

and using documents and technical documentation as well as occupational requirements

Taking cultural identities into account in discussions

Knowledge Evaluating circuitry documentation, technical

drawings, and parts lists Visually representing facts, creating

protocols, using English technical terms in communication

Skills:

17

Protocols and protocol compositionCircuitry documentationTechnical drawingsParts listsTechnical documentationDatabanksData protectionCultural communication

Creating and using circuit plans, technical drawings, and parts lists

Creating sketches Managing, backing up, and archiving data

and documents while also protecting the data

3 Basic special modulesName of discipline (module):3.1 Manufacturing and checking electrical machines

Contents:Principle of electromagnetic energy conversionInactive electric machines, windings, winding types and forms, and insulationRotary electric machinesAssembly processComponents of electric machinesDesigns, storage, housingOperational modes, cooling Structure of drive systemsControl elementsDirect and alternating current machinesSafety equipmentMeasuring equipment and processes, load characteristicsCorrelation between winding setup and operating behaviourDevices and assembly groups for operating and controlling drivesStarting and braking procedureSpeed controlTesting procedureTechnical discussionTechnical documentation

Competences: Classifying and exploring the mode of

operation and operating behaviour of electric machines while complying with the relevant safety regulations and protective measures during operation

Commissioning electric machines while taking information provided by the manufacturer, customer requirements, environmental conditions, and safety regulations into account

Creating documentation of electric machines, their condition, and ways to use them

Knowledge Analysing the construction and mode of

operation of electric machines Describing the safety equipment on electric

machines Describing the advantages and disadvantages

of the machines examined while taking the areas of application and economic aspects into account

Explaining the application cases for inactive electric machines and the requirements that apply

Explaining the application cases for rotary electric machines, how they are integrated into drive systems, and the necessary devices and assembly groups for operating and controlling them

Skills: Constructing plug-in units, housing, and

circuit device combinations Selecting and parametrizing frequency

converters Connecting and starting up electric machines Installing safety equipment, insulation, and

cover panels

18

Name of discipline (module):3.2 Installing and removing electrical machinery

Contents:CouplingsGearboxBrakesCauses of malfunctionsCorrosion, breakage, wearBalancingDisposal regulations General and group-specific drawings, assembly plansParts listsTest protocolsRecommissioningMeasuring regulations

Competences: Selecting, adapting, and installing

mechanical components for electric machines Processing various materials, particularly

through the processes of drilling, sinking, tapping, grinding, and in part also with turning and milling

Localizing malfunctions in electric machines and making suggestions for how to eliminate the problem and repair the machine

Producing and installing single layer windings

Producing and installing windings for inactive electric machines

Knowledge Identifying function correlations between

components and developing assembly and disassembly plans for simple systems

Describing the necessary tools and steps taken to mechanically adapt, assemble, and disassemble the machines

Evaluating assembly processes while taking the cost effectiveness and factors related to occupational safety and environmental protection into account

Explaining the causes of damage and wear in electric machines

Explaining and sketching out winding plans

Skills: Using configuration, circuit, and assembly

plans Recording winding data Fabricating insulation for electric machines Checking the functionality of assembly

groups and exchanging defective parts Adapting plans to the conditions present, also

with the help of a computerName of discipline (module):3.3 Establishing and maintaining energy-related systems I

Contents:Wires and wiring systemsSwitchgearsProtective devices for electric networksTypes of networksDecentralized energy supply systemsPower engineering systems in buildings,

Competences: Planning order processing in coordination

with all people involved in the process

Knowledge Analysing customer orders for building

energy supply systems Observing safety regulations, accident

prevention regulations and environmental regulations

19

especially in special rooms and outsideCompensationData logging, processing and analysingFault types and methods of troubleshootingRecycling and disposal

Skills: Assessing the interaction of components Procuring assignment-relevant information

about structure and operational performance of low-voltage switchgears

Controlling and assessing work processes and work results in consideration of economic, ecological and safety-related aspects

5 Industrial training and professional practiceName of discipline (module)5.1 Industrial training

ContentsPractical applications of contents of modules 2.1 - 2.5; 3.1 - 3.3 (industrial context)

Competencies, knowledge and skills of modules 2.1 - 2.5; 3.1 - 3.3, but with more emphasis of practical implications in industries (companies, enterprises)

Name of discipline (module)5.2 Professional practice

ContentsPractice, practical applications of contents of modules 2.1 - 2.5; 3.1 - 3.3

Competencies, knowledge and skills of modules 2.1 - 2.5; 3.1 - 3.3, but with more emphasis of practical implications

8 Professional modulesName of discipline (module):8.1 Planning and executing electrical installations II

Contents:Job scheduling, order realization Energy requirements of a system or a device Safety regulations Electromagnetic compatibilityInstallation technology Key parameters of equipment Types of wiring diagrams Performance dimensioning Labour organization Cost calculation, quoting

Competences: Starting up and testing the functionality of an

installed system Recording performance data and creating

system documentation Following electro-technical rules for setting

up, modifying, maintaining, and operating electrical systems and equipment

Knowledge: Procedure for completing assignments,

inventory control, and coordination with others

Safety regulations, accident prevention regulations, safety rules

Knowledge of specialized terminology in the local language and in English

Skills: Finding and eliminating errors Selecting the appropriate work material while

taking accident prevention regulations into account

Disassembling and assembling assembly groups and customizing parts through mechanical processing

20

Avoiding waste and identifying the appropriate disposal options for waste materials

Name of discipline (module):8.2 Analysing, programming and realizing controls for systems

Contents:Block diagram, EVA principle, sensors, actuators, interfacesAction chain, operation descriptionsConnection and stored programs for signal processingLogical basic connections, storage functionsNorms, requirements, and regulationsTechnical documentation

Competences: Analysing control systems and devices Visualizing structural setup and functional

correlations Working largely independently to plan and

execute adaptations and changes for control units

Knowledge Using techniques for differentiating between

controls and evaluating their advantages and disadvantages

Explaining the difference between control and regulation processes

Explaining application cases from financial and safety perspectives

Using English language documentation and English technical terms

Skills: Changing control units while also selecting

the appropriate assembly groups and components

Starting up control units Checking the functionality of control units

and recording measurements gathered for the performance data

Optimizing functionality by changing settings

Processing documentation with or without application-specific software

Name of discipline (module):8.3 Operational and technical communication II

Contents:Sources of informationTeamworkDocumentationHandbooksOperation and instruction manualsProtocols and protocol compositionCircuitry documentationTechnical drawingsParts listsTechnical documentationDatabanks

Competences: Selecting sources of information, obtaining

and evaluating information – also in English Putting together, supplementing, evaluating,

and using documents and technical documentation as well as occupational requirements

Having situation-appropriate, goal-oriented discussions with customers, superiors, and within the team

Taking cultural identities into account in discussions

Documenting and presenting results of meetings

Knowledge

21

Data protectionCultural communication

Evaluating circuitry documentation, technical drawings, and parts lists

Visually representing facts, creating protocols, using English technical terms in communication

Using information from databanks, technical documents, and technical files – also in English

Skills: Managing, backing up, and archiving data

and documents while also protecting the data Resolving conflicts within the team Using standard software to complete tasks

9 Special modulesName of discipline (module):9.1 Installing and maintaining propulsion systems

Contents:Structure of drive systemsControl elementsDirect and alternating current machinesSafety equipmentConstruction forms, operating modes, types of protection and cooling of machinesDevices and assembly groups for operating and controlling drivesStarting and braking procedureSpeed controlTesting procedureTechnical discussionTechnical documentation

Competences: Planning the order procession of the

customers' requirements for the drive Coordinating the procurement of task-

relevant information, also in English, in the team

Assessing work results holistically

Knowledge Analysing orders for drive systems and

planning the technical realization of the drive Choosing necessary devices, assemblies and

protection measures while taking account of functional, economic and ecological aspects and scaling them

Using and keeping norms, regulations and rules for placing electric drives and bringing them into service

Skills: Constructing electric and pneumatic drives,

checking them and bringing them into service after the parameter setting of the components

Having technical discussions and analysing insights

Measuring and documenting operation data, creating technical documentations via computer as well as circuit documents, presenting them to the users and instructing them

Meeting work and environmental protection requirements

Appropriately inspecting and documentingName of discipline (module):9.2 Running and commissioning operating

Competences: Planning the order processing of electric

22

building services systems

Contents:Customer advisory serviceMaterials scheduling and calculationLighting engineeringHazard detection and fire alarm systemsCommunication systemsLightning protection Building systems technologyLoad managementVisualization softwareNorms, requirements, and regulations

systems in buildings with technical requirements and time limits

Coordinating time and work schedules in a team while also considering other work processes

Inspecting building systems, localizing faults systematically and taking measures for troubleshooting

Knowledge Reviewing their decisions for feasibility,

profitability and environmental compatibility Being aware of safety and fire protection

regulations and determining measures for compliance

Making use of technical literature, product data bases, device and system instructions that may also be in English

Skills: Analysing , complementing, installing and

configuring building technology systems, including communication systems, and taking into account visualization in the project planning

Inspecting the finished building technology systems, bringing them into service and instructing the users

Making use of diagnostic systems and interpreting operating protocols and error lists

Utilizing complaints to improve systems and services

Processing and creating the service documents necessary for the operation of systems and using customary software

Name of discipline (module):9.3 Establishing and maintaining energy-related systems II

Contents:Wires and wiring systemsSwitchgearsProtective devices for electric networksTypes of networksDecentralized energy supply systemsPower engineering systems in buildings, especially in special rooms and outsideCompensationData logging, processing and analysing

Competences: Scheduling work steps and making decisions

on work organization so that the systems are assembled and installed in a targeted and efficient manner

Knowledge Documenting work processes and changes of

the systems Observing safety regulations, accident

prevention regulations and environmental regulations

Skills: Applying measuring and inspection

23

Fault types and methods of troubleshootingRecycling and disposal

procedures and making changes and adapting settings if necessary

Carrying out re-inspections in due time, localizing and analysing operation faults

Discussing possible solutions with the involved parties to eradicate the flaw and fix it in a targeted manner

Name of discipline (module):9.4 Installing and commissioning of electrical equipment

Contents:Hoists, fasteners and means of transport Anchorages, supporting structures and consolesSubfloor examinationAssembly of combinationsPositioning of machines, drive systemsConnection techniques for lines and communication technologyStart-up of systemsSafety regulationsSafety equipmentDocumentation

Competences: Checking the compliance of measures for

electromagnetic compatibility, creating test logs, making and adapting documentation, transferring to an installation or system

Knowledge Establishing earthing and potential

equalization, measuring and assessing earth and loop resistance

Skills: Choosing, rigging up and dismantling

ladders, scaffolds and mounting platforms Choosing and making use of hoists, fasteners

and means of transport, securing load and transporting

Checking the subfloor for applicability of fixtures, preparing anchorages and mounting supporting structures and consoles

Setting up, aligning, mounting and linking machines, devices, drive systems and other equipment

Assembling and positioning drawers, housings and switchgear combinations

Installing, wiring and marking switchgears Name of discipline (module):9.5 Configuring and programming of control systems I

Contents:Assemblies of the measurement, control and regulation systemMeasurement, control and regulation technology software and hardwareNetworks, bus systemsPrograms and storage media for backup Programming of controls Analysis of control programs

Competences: Setting hard and software of the

measurement, control and regulation system components, adapting them and bringing them into service

Knowledge Adapting architectures, protocols, interfaces

of automation devices to networks and bus systems

Skills: Installing and configurating application

software Analysing, creating and altering control

programs 11 Industrial training and professional practice

24

Name of discipline (module)11.1 Industrial training

ContentsPractical applications of contents of modules 8.1 – 8.3; 9.1 - 9.5 (industrial context)

Competencies, knowledge and skills of modules 8.1 – 8.3; 9.1 - 9.5, but with more emphasis of practical implications in industries (companies, enterprises)


ContentsPractice, practical applications of contents of modules 8.1 – 8.3; 9.1 - 9.5

Competencies, knowledge and skills of modules 8.1 – 8.3; 9.1 - 9.5, but with more emphasis of practical implications

16 Advanced professional modulesName of discipline (module):16.1 Planning, implementing and maintaining electrical systems

Contents:Project descriptionTime and work managementProfitabilityFacility and product designNorms, requirements, and regulationsQuality assuranceProject assessment

Maintenance conceptsCustomer advice and instructionProcess documentationKnowledge management

Competences: Planning projects for electro-technical

facilities Planning, developing and realizing practice-

oriented solutions Assuming responsibility for the project

organization as well as the coordination of learning and working processes

Considering basic norms and processes in quality management and thereby ensuring the quality of products and processes

Assessing project results and operation processes with regard to technical and economic aspects as well as organizational aspects concerning development and workflow

Planning measures for maintenance and modification in electro-technical facilities

Reflecting their professional development and work processes

Using appropriate qualification opportunities as well as different learning techniques and media to develop their competences and qualifications

Knowledge Defining goals, analysing and structuring

tasks with regard to their feasibility and considering the area of operation when selecting projects

Documenting project progress, analysing and assessing the progression

Considering recycling options and environmental compatibility during the project realization

Creating and modifying documentations, using English documents as well, and

25

presenting results Analysing malfunctions and applying

methods and strategies to systematically isolate and clear faults in electro-technical systems or components

Using English documents for project documentations and presenting results

Skills: Setting up electro-technical facilities and

components Bringing electro-technical facilities and

components into service and checking sub-functions and main functions

Demonstrating set-up and functions of the facility and its components

Using up-to-date information and communication media

Altering electro-technical facilities and components so that they suit customer requirements and recording alterations professionally

Instructing customers on how to operate the altered facilities, informing them about legal requirements concerning maintenance and explaining the altered maintenance requirements

Name of discipline (module):16.2 Analysis of technical order, solution development

Contents:Electric machinesPower supplyCircuitsOrder documentsPosition and installation plansProtective measures

Competences: Distinguishing electric machines according to

their type and function Assessing the existing power supply,

planning alterations, determining circuits and protective measures

Knowledge Reading and applying position and

installation plans Examining order documents and adjusting

them to local conditions

Skills: Sketching and drawing up position and

installation plans Choosing components of the drive system

17 Advanced special modulesName of discipline (module):17.1 Technical service and operation

Contents:Services

Competences: Informing customers about warranty claims

and advising them in regard to technical and economical feasibility

Delivering plants, instructing customers on

26

EstimatesMonitoring of plantsConsumption data Delivery of plantsInstructions for technical facilities

how to handle technical facilities

Knowledge Documenting services Gathering consumption data about energy

and equipment

Skills: Providing and performing services Participating in preparation of offers and

quotations under consideration of company guidelines

Monitoring technical facilities Conducting remote diagnostics and

maintenance Analysing data from the system and the

diagnostic data and using them for improvements

Running and adapting visualization applications of technical facilities

Finding causes for deviations from the setpoint (consumption data of energy and equipment), optimizing consumption

Name of discipline (module):17.2 Commissioning and maintaining automated systems I

Contents:Levels of automation systemsParameters and norms of bus systemsConfiguration of networks and bus systemsDigital software controlOperating modes of automated systemsWord processing, analogue value processingControl of drive systems that are able to communicate

Competences: Planning controls for automated systems Organizing and optimizing work processes

based on the division of labour

Knowledge Integrating components in superior

automation systems via industrial communication systems

Calculating the consequences of error sources on the facilities and services and taking preventive steps

Skills: Installing automated systems Configuring and parameterizing automated

systems and their integrated drive systems Taking topology and structure of automation

systems into account Recording and analysing the data interchange

and using instruments for developing and visualizing programs

Using and keeping norms, regulations and rules for placing and bringing into service automated systems as well as electric drives capable of communicating and heeding industrial safety regulations

27

Documenting professionallyName of discipline (module):17.3 Measuring and analysing electrical functions and systems

Contents:Methods of circuit analysisAnalogue and digital assembly groupsStandard solutions for circuitryMethods of fault localizationSimulation softwareMeasuring and testing proceduresTest regulations, test protocolsTechnical circuitry documentation

Competences: Checking functionality of systems and

components, interpreting data protocols Selecting measuring processes and measuring

devices

Knowledge Following signals and checking them at

interfaces Measuring, assessing and calculating electric

values

Skills: Checking characteristics and functions of

components Analysing control circuits Systematically troubleshooting Checking and adjusting sensors and actuators Testing and assessing controls concerning

their function Name of discipline (module):17.4 Installing and commissioning of electrical equipment II

Contents:Assembly of combinationsPositioning of machines, drive systemsConnection techniques for lines and communication technologyStart-up of systemsLighting systemsEmergency shut-off and reporting systemSafety regulationsSafety equipmentRecord keeping

Competences: Adjusting protective devices and checking

their efficacy, ensuring efficacy of protection measures

Knowledge Parameterizing drive systems and bringing

them into service, setting operating values

Skills: Installing, wiring and marking controlling,

measuring and monitoring equipment Mounting protective devices, casings and

insulations Assembly of buses Preparing and linking conductions and wires

of the energy system Processing conductions of the

communications system with different connection techniques

Connecting components via pipes and hose lines

Bringing main and auxiliary circuits into service

Installing, checking and activating signal and data transmission systems

Checking non-electrical components of facilities, especially pneumatic components

Mounting and installing lighting systems

28

Checking emergency shut-off and mechanical safety devices

Name of discipline (module):17.5 Maintaining equipment and systems

Contents:Energy distribution systemsSystem parametersInspection of facilitiesDiagnostic systemsMaintenance of processing machines and communication systemsDocumentation of maintenance measuresProtective measures and safety devices

Competences: Planning maintenance and inspection

measures

Knowledge Inspecting systems, checking functions of

machines and safety devices as well as logging inspections

Assessing energy distribution systems Comparing system parameters with given

values and setting them

Skills: Servicing systems according to maintenance

plans, replacing wear parts as part of preventive maintenance measures

Using diagnosis systems, checking functions of components, replacing defective components

Servicing and maintaining decentralized energy supply systems

Servicing and maintaining energy distribution systems

Servicing and maintaining processing machines

Servicing and maintaining communication systems

Installing protective measures and safety devices when devices or parts of systems have been brought into service again and testing their efficacy

Record maintenance measures19 Industrial training and professional practice

Name of discipline (module)19.1 Industrial training

ContentsAssembly and dismantling of componentsConnection technologies, preparation Conduction installation systemsInstallation of conduction linesElectro-technical rules for setting up, modifying, maintaining, and operating electrical systems and equipmentCommissioning of facilities and devicesWaste removalWork and safety regulations

Competences: Producing electric devices or constructing

electric facilities, bringing devices or facilities into service

Assessing conductions and their protective devices as well as other equipment with a special focus on ampacity

Assessing dangers that emerge from operating electric devices, equipment and facilities, and ensuring safe operation with protective measures

Classifying and exploring the mode of operation and operating behaviour of electric machines while complying with the relevant safety regulations and protective measures

29

Current carrying capacity of conductions, protection devices and equipmentProtective conductor and equipotential bonding conductorProtection classes and their assessmentElectric shock under fault conditions, (especially by turning off overcurrent protection devices and fault current protection devices)Fire regulations

Principle of electromagnetic energy conversionInactive electric machines, windings, winding types and forms, and insulationRotary electric machinesAssembly processComponents of electric machinesDesigns, storage, housingOperational modes, cooling Structure of drive systemsControl elementsDirect and alternating current machinesSafety equipmentMeasuring equipment and processes, load characteristicsCorrelation between winding setup and operating behaviourDevices and assembly groups for operating and controlling drivesStarting and braking procedureSpeed controlTesting procedureTechnical discussionTechnical documentation

CouplingsGearboxBrakesCauses of malfunctionsCorrosion, breakage, wearBalancingDisposal regulations General and group-specific drawings, assembly plansParts listsTest protocolsRecommissioningMeasuring regulations

Assemblies of the measurement, control and

during operation Commissioning electric machines while

taking information provided by the manufacturer, customer requirements, environmental conditions, and safety regulations into account

Creating documentation of electric machines, their condition, and ways to use them

Selecting, adapting, and installing mechanical components for electric machines

Processing various materials, particularly through the processes of drilling, sinking, tapping, grinding, and in part also with turning and milling

Localizing malfunctions in electric machines and making suggestions for how to eliminate the problem and get the machine working again

Producing and installing single layer windings

Producing and installing windings for inactive electric machines

Setting hard and software of the measurement, control and regulation system components, adapting them and bringing them into service

Informing customers about warranty claims and advising them in regard to technical and economical feasibility

Delivering plants, instructing customers on how to handle technical facilities

Planning controls for complex automated systems

Organizing and optimizing their work processes based on the division of labour

Knowledge Determining conductive lines and device

assembly locations while taking electromagnetic compatibility into account

Considering the electrotechnical rules for setting up, modifying, maintaining, and operating electrical systems and equipment

Assessing protection types for electric devices or systems in regards to environmental conditions and additional factors to consider for special types of spaces

Assessing basic safety measures for preventing electric shocks

Assessing the electric safety of non-stationary equipment

30

regulation systemMeasurement, control and regulation technology software and hardwareNetworks, bus systemsPrograms and storage media for backupProgramming of controlsAnalysis of control programs

ServicesEstimatesMonitoring of plantsConsumption data Delivery of plantsInstructions for technical facilities

Levels of automation systemsParameters and norms of bus systemsConfiguration of networks and bus systemsDigital software controlOperating modes of automated systemsWord processing, analogue value processingControl of drive systems that are able to communicateInverter-fed drivesCircuit feedback and EMC measuresFault probability analysis and fault effect analysisContinuous improvement processConflict resolution strategies

Analysing the construction and mode of operation of electric machines

Describing the safety equipment on electric machines

Describing the advantages and disadvantages of the machines examined while taking the areas of application and economic aspects into account

Explaining the application cases for inactive electric machines and the requirements that apply

Explaining the application cases for rotary electric machines, how they are integrated into drive systems, and the necessary devices and assembly groups for operating and controlling them

Identifying function correlations between components and developing assembly and disassembly plans for simple systems

Describing the necessary tools and steps taken to mechanically adapt, assemble, and disassemble the machines

Evaluating assembly processes while taking the cost effectiveness and factors related to occupational safety and environmental protection into account

Explaining the causes of damage and wear in electric machines

Explaining and sketching out winding plans Adapting architectures, protocols, interfaces


Documenting services Gathering consumption data about energy

and equipment Creating and modifying documentations,

using English documents as well, and presenting results

Using standard and application-specific software

Preventing possible error sources during the planning of facilities by making prospective analyses

Skills: Disassembling and assembling assembly

groups and adapting parts through mechanical processing

Choosing and finishing conductions and connecting assembly groups and devices with different connection technology

31

Choosing and assembling electric equipment and conduction installation systems

Installing conductions Avoiding waste and assessing waste

materials, not used equipment and components with regard to their disposal, storing them environmentally appropriate and preparing them for disposal

Checking and assessing functionality of protective and equipotential bonding conductors

Measuring and assessing insulation resistances

Evaluating the effectiveness of measures countering electric shocks when a malfunction occurs, particularly those malfunctions caused by turning off overload protection and fault current protection units

Considering fire regulations when operating and setting up electric devices and systems

Constructing plug-in units, housing, and circuit device combinations

Selecting and parameterizing frequency converters

Connecting and starting up electric machines Installing safety equipment, insulation, and

cover panels Using configuration, circuit, and assembly

plans Recording winding data Fabricating insulation for electric machines Checking the functionality of assembly

groups and exchanging defective parts Adapting plans to the conditions present, also

with the help of a computer Installing and configuring application

software Analysing, creating and altering control

programs Checking functional routines and adapting

program operation Installing storage media and programs for

backup Providing and performing services Participating in preparation of offers and

quotations under consideration of company guidelines

Monitoring technical facilities Conducting remote diagnostics and

maintenance Analysing data from the system and the

32

diagnostic data and using them for improvements

Running and adapting visualization applications of technical facilities

Finding causes for deviations from the setpoint (consumption data of energy and equipment), optimizing consumption

Analysing controls of existing systems and installing complex automated systems

Checking automated systems independently for function and safety and bringing them into service

Performing maintenance and diagnosis, also remote diagnosis, on automated systems and drives

Using strategies to systematically isolate and clear faults during maintenance and diagnosis


ContentsProduct description Communication process Objection handling Customer behaviour Customer relationship management

Order processing in generalEconomic, ecological and safety aspects in the planning of the order processingScheduling frameworks, deadlinesCustomer orientationDocumentationAssessment of work results and performanceIn-house quality assurance systems (TQM)Environmental protection

Tool selectionProject completionWork organizationOperational processes, work proceduresTeamworkScheduling, sequences of deadlines

Competences: Ascertaining expectations and demand of

customers, developing solution approaches and providing realization opportunities

Organizing information exchange with the customer

Informing customers about special offers and advising them, accepting orders

Analysing the initial condition, coordinating technical and organizational interfaces, documenting interfaces, setting goals for the order, defining subtasks, creating technical documents and participating in the cost planning

Inviting, examining and assessing offers and quotations with regard to company regulations

Planning work processes and subtasks while taking economic and deadline-related requirements into account

Checking and visually presenting various solution options for work processes and comparing the cost effectiveness of the variations

Planning and carrying out tasks in a team Using IT systems to plan and carry out

projects while also keeping track of deadlines

Knowledge Explaining features, instructing on the

operation, giving information about dangers and safety regulations

33

Pointing out maintenance work and intervals to the customer

Procuring and assessing information, using and adapting documentations, observing technological developments, considering safety-relevant documents

Planning the order processing and adjusting it to preceding and subsequent areas, making planning documents

Selecting appropriate tools and materials Recording and evaluating operationally

relevant data Identification of qualification deficits,

utilization of qualification opportunities

Skills: Recording fault reports Agreeing specific details during the order

processing, showing solution options if there are problems in the order processing

Providing technical support Arranging for external labour and

supervising them Executing orders especially with due regard

to work safety and environmental protection, keeping in mind the compliance of deadlines

Choosing test types and testing instruments, ascertain deployability of the testing instruments, applying test plans according to the operational regulations

Taking heed of norms and specifications for the quality and safety of products as well as quality

Ensuring completion of the order, using a quality assurance system as well as looking for error reasons systematically, removing and documenting them.

Documenting the order processing, charging services, create invoice data, making a post calculation

Setting up a workstation or assembly station while taking operational requirements into account

Identifying, choosing, requesting in a timely manner, inspecting, transporting, storing, and providing tools and materials needed for the work procedure

Using instruments to complete a project and for tracking deadlines

Using a variety of study techniques Selecting and using testing processes and

34

equipment Determining the usefulness of testing

equipment Checking, evaluating, and documenting work

results Contributing to the ongoing improvement of

work processes in your own work area 23 Special advanced modules

Name of discipline (module):23.1 Configuring and programming of control systems II

Contents:Complex assemblies of the measurement, control and regulation systemMeasurement, control and regulation technology software and hardwareNetworks, bus systemsPrograms and storage media for backupProgramming of complex controlsAnalysis of control programs

Competences: Setting hard and software of the complex

measurement, control and regulation system components, adapting them and bringing them into service

Knowledge Adapting architectures, protocols, interfaces


Skills: Checking functional routines and adapting

program operation Installing storage media and programs for

data backupName of discipline (module):23.2 Commissioning and maintaining automated systems II

Contents:Configuration of networks and bus systemsControl of complex drive systems that are able to communicateInverter-fed drivesCircuit feedback and EMC measuresFault probability analysis and fault effect analysisContinuous improvement processConflict resolution strategies

Competences: Planning controls for complex automated

systems Organizing and optimizing their work

processes based on the division of labour

Knowledge Creating and modifying documentations,

using English documents as well, and presenting results

Using standard and application-specific software

Preventing possible error sources during the planning of facilities by making prospective analyses

Skills: Analysing controls of existing systems and

installing complex automated systems Checking automated systems independently

for function and safety and bringing them into service

Performing maintenance and diagnosis, also remote diagnosis, on automated systems and drives

Using strategies to systematically isolate and

35

clear faults during maintenance and diagnosisName of discipline (module):23.3 Business processes and quality management

Contents:Order processing in generalEconomic, ecological and safety aspects in the planning of the order processingScheduling frameworks, deadlinesCustomer orientationDocumentationAssessment of work results and performanceIn-house quality assurance systems (TQM)Environmental protection

Competences: Informing customers about special offers and

advising them, accepting orders Analysing the initial condition, coordinating

technical and organizational interfaces, documenting interfaces, setting goals for the order, defining subtasks, creating technical documents and participating in the cost planning

Inviting, examining and assessing offers and quotations with regard to company regulations

Knowledge Procuring and assessing information, using

and adapting documentations, observing technological developments, considering safety-relevant documents

Planning the order processing and adjusting it to preceding and subsequent areas, making planning documents

Skills: Arranging for external labour and

supervising them Executing orders especially with due regard

to work safety and environmental protection, keeping in mind the compliance of deadlines

Choosing test types and testing instruments, ascertaining deployability of the testing instruments, applying test plans according to the operational regulations

Taking heed of norms and specifications for the quality and safety of products as well as quality

Ensuring completion of the order, using a quality assurance system as well as looking for error reasons systematically, removing and documenting them.

Documenting the order processing, charging services, create invoice data, making a post calculation

24 Industrial training and professional practiceName of discipline (module):24.1 Industrial training

Contents:Product description Communication process

Competences: Ascertaining expectations and demand of

customers, developing solution approaches and providing realization opportunities

Organizing information exchange with the customer

36

Objection handling Customer behaviour Customer relationship management

Knowledge Explaining features, instructing on the

operation, giving information about dangers and safety regulations

Pointing out maintenance work and intervals to the customer

Skills: Record fault reports Agreeing specific details during the order

processing, showing solution options if there are problems in the order processing

Providing technical support Name of discipline (module):24.2 Professional practice

Contents:Project completionWork organizationOperational processes, work proceduresTeamworkScheduling, sequences of deadlinesAppointment chainsBusiness management aspects and cost-effectivenessQuality control

Competences: Planning and conducting work processes and

subtasks while taking economic and deadline-related requirements into account

Checking and visually presenting various solution options for work processes and comparing the cost effectiveness of the variations

Planning and carrying out tasks in a team Using IT systems to plan and carry out

projects while also keeping track of deadlines Examining solution options, visualizing and

comparing them in terms of profitability Contributing to a continuous improvement in

work procedures in your own working area

Knowledge Selecting appropriate tools and materials Recording and evaluating operationally

relevant data Identification of qualification deficits,

utilization of qualification opportunities Choosing, checking, transporting and

providing tools and materials and requesting them on time

Acquiring and assessing economically relevant data

Ascertaining skill gaps, using qualification opportunities

Skills: Setting up a workstation or assembly station

while taking operational requirements into account

Identifying, choosing, requesting in a timely manner, inspecting, transporting, storing, and

37

providing tools and materials needed for the work procedure

Using instruments to complete a project and for tracking deadlines

Using a variety of learning and study techniques

Selecting and using testing processes and equipment

Determining the usefulness of testing equipment

Checking, controlling, evaluating, assessing and documenting work results

Contributing to the ongoing improvement of work processes in your own work area

Choosing and using different test methods and testing instruments, checking usability of test equipment

4. LIST OF EQUIPMENTBasics in electro technology

1 Advanced Science Kit - Set ESA 12 COM3LAB course: DC Technology I3 COM3LAB course: DC Technology II4 COM3LAB Master Unit5 Safety cable 2mm6 Mains cable with hock-proof plug and cold connector7 Advanced Science Kit - Set BEL8 Advanced Science Kit - Set ELI 19 AC/DC Power supply 0...12 V/ 3 A10 Batteries 1.5 V (D, mono),11 Multimeter LDanalog 2012 Bulb 4 V/0.16 W, E1013 Bulb 12 V/3 W, E1014 Bulb 2.5 V/0.25 W, E1015 Constantan wire, 0.35 mm Ø, 100 m16 Chrome-nickel wire, 0.25 mm Ø, 100 m17 Chrome-nickel wire, 0.35 mm Ø, 100 m18 Iron wire, 0.20 mm Ø, 100 m19 Scissors 125 mm

38

20 Candle21 Connecting lead 19 A, 25 cm, red/blue, pair22 Connecting lead 19 A, 50 cm, red/blue, pair23 Connecting lead 19 A, 25 cm, black, pair24 D.C. CIRCUITS

Basic Set T 2.2, STE25 Plug-in board DIN A4, STE26 Battery 1.5 V (AA),27 Bridging plugs STE 2/1928 Connecting lead 19 A, 50 cm, red29 Connecting lead 19 A, 50 cm, black30 Electromagnetism & Induction

Advanced Science Kit - Set ELI 231 Capacitor (el.) 100 µF, STE 2/1932 Capacitor (el.) 470 µF, STE 2/1933 COM3LAB Course: AC Technology I34 COM3LAB Course: AC Technology II35 A.C. Circuits

Basic Set T 2.336 Function generator 200 kHz37 Plug-in power supply 12 V AC38 Oscilloscope 30 MHz, two-channel, analogous39 Panel frame L150, One Level40 COM3LAB course: Three-phase technology41 "Three-Phase Transformers and

Transformer Circuits"Basic Set T 2.4.1

42 Three-phase voltage supply, 3×12 V, STE 6/10043 Set 6 two-way adapters, red44 Sensor-CASSY 2 Starter45 Connecting lead 32 A, 25 cm, black46 Connecting lead 32 A, 50 cm, black47 Connecting lead 32 A, 50 cm, blue48 Connecting lead 32 A, 100 cm, red49 Connecting lead 32 A, 100 cm, black50 Bridging plugs STE 2/1951 COM3LAB course: Electrical machines I52 ELM Coil 250 turns53 ELM Short-circuit rotor54 ELM Brush55 Allen wrench56 ELM Centering disc

39

57 Brush holder58 ELM Two-pole rotor59 ELM Three-pole rotor60 ELM Drum rotor61 ELM Rotating field attachment62 ELM Magnetic needle rotor63 ELM Aluminium ring with iron disc64 Oil 100 ml in dropping bottle65 Basic Machine Unit66 Basic Connection Unit67 Set of Masks68 Starter69 Field Regulator70 Star-Delta Load71 Driving Unit72 Driving belt long73 ELM Pole piece for magnets74 ELM Wide pole piece for coils75 ELM Coil 500 turns76 ELM Narrow pole piece for coils77 ELM Split pole piece for coils78 Bulb 6 V/1.1 W, E1079 Bulb 15 V/2 W, E1080 Magnets, 35 mm Ø, pair81 Capacitor 4.7 µF, STE 2/1982 Lamp holder E10, top, STE 2/1983 Key switch (NO), STE 2/1984 Toggle switch STE 2/1985 Multimeter Metrahit Pro86 Panel frame T130, Two Level87 3-Phase Voltage / Exp. Transformer88 Storage tray for ELM apparatus89 Safety bridging plugs, black90 Safety Bridging Plugs with Tap, black100 Connecting lead 19 A102 COM3LAB Course: Electronic Components I103 COM3LAB Course: Electronic Components II104 Discrete components and basic electronic circuits105 Plug-in board 297 mm x 300 mm, STE106 Function generator S 12

40

107 Digital multimeter DMM 121108 Screened cable BNC/4 mm plug109 Bridging plugs STE 2/19110 Logikboard 1

Digital electronics111 Logikboard 2

Digital electronics112 Connecting Leads, 8 cm113 Adapter cables 2/4 mm, 30 cm, blue

Protection circuits VDE 0100 (module system)114 House service connection115 Earthing Resistors BS 0.2116 Current-consuming equipment - Filament lamp BS 0.3117 Current-consuming equipment with body-contact BS 0.4118 Residual Current Device e.l.c.b. BS 0.7119 Ground-leakage monitor BS 0.8120 Transformer BS 0.9121 Extra-low voltage transformer122 Isolating Transformer123 Model of the human body BS 0.10124 Socket outlet without earth contact BS 0.12125 Current-using device, extra low voltage BS 0.13126 Mains socket with earthing contact BS 4.120127 Incandescent lamp E 14, 230 V, 25 W128 Incandescent lamp E 14, 230 V, 5 / 7 W129 Multimeter METRAport 3A130 Tester PROFITEST 0100S-II131 Safety bridging plugs, yellow/green132 Safety connecting leads, 32 A133 Assembly Grid L130134 Mobile cable holder135 Panel frame VT180, Three Level136 TFT Monitor frame TPS137 Equipment Platform 500 mm138 Grooved mat cabinet 1200139 Shelf 1200140 Shelf 1200 with 1 grooved mat141 Shelf 1200 with 2 grooved mats142 Assembly set mussel-type handle

Installation circuits with switches, panel system201 Distribution box P 4.101

41

202 Automatic circuit breaker - 6 A203 Series switch204 Change-over switch, left205 Change-over switch, right206 Intermediate switch207 Lamp socket, E14, single208 Schuko Socket209 Incandescent lamp E 14, 230 V, 25 W210 Mains connection AC, 10 A211 Voltage and continuity tester 6...400 V212 Safety connecting leads, 32 A213 Safety connecting lead 32 A, yellow/green

Protection circuits VDE 0100 (module system) T4.3.6 U 0100214 House service connection215 Earthing Resistors BS 0.2216 Current-consuming equipment – Filament lamp BS 0.3217 Current-consuming equipment with body-contact 0.4218 Residual Current Device e.l.c.b.219 Ground-leakage monitor220 Transformer221 Extra-low voltage transformer222 Isolating Transformer223 Model of the human body BS 0.10224 Socket outlet without earth contact225 Current-using device, extra low voltage226 Mains socket with earthing contact BS 4.120227 Incandescent lamp E 14, 230 V, 25 W228 Incandescent lamp E 14, 230 V, 5 / 7 W229 Multimeter METRAport 3A230 Tester PROFITEST 0100S-II231 Safety bridging plugs, black232 Safety bridging plugs, yellow/green233 Safety connecting leads, 32 A234 Assembly Grid L130235 Test and Fault Simulator VDE236 Safety connecting leads237 SATURN 100 Plus

Basic circuits of control technology I238 Signal Lamp, Threefold239 Autom. Circ. Breaker Fourfold

42

240 Limit Switch 1NO 1NC241 Operating panel242 Base unit control circuits243 Storage box for control circuit244 Auxiliary Contactor 4NO 4NC245 PWR Contactor 3-pole 3NC 2NO246 Three-Phase Supply Unit247 Safety bridging plugs, black248 Safety bridging plugs, yellow/green249 Safety connecting leads, 32 A250 Safety connecting lead 32 A, yellow/green251 Shaft End Guard 0.1/0.3252 Squirrel Cage Motor Basic 400/690/0.3253 Motor Protection Relay 0.6-1254 Motor Protection Switch 0.6-1 A255 COM3LAB Master Unit256 COM3LAB Course: Automation and Bus Technology257 Safety cable 2mm258 Mains cable with hock-proof plug and cold connector259 DVD: COM3LAB Software

The LOGO! small controller trainer T9.5.1.11260

LOGO! 24V Relais mounted on board261

Plug-in power supply for torsion pendulum262

Adapter for LOGO!

PROFIBUS-Master with Siemens S7-300, complete set (panel system) T9.5.1.1263

Trainer basic panel 264

Connecting adapter for power supply265

Documentation S7-software on CD-ROM -D266

Power supply PS 307 incl. power cord267

Micro Memory Card, 64 Kb, forS7-3xxC268

PC adapter for S7-300 USB269

Simatic S7-300, CPU 314C-2 DP compact270

Power supply 24 V DC, 6.5 A, for 230 V AC43

271Decentralized periphery ET200S with 4 DI / 2 DO

272P Operator Panel OP77B incl. WinCC Flexible

273Frequency Inverter 300 W Micromaster 420 P 10.367

274PROFIBUS-Module for Micromaster 420 / 440

275Stripping tool for PROFIBUS-DP cable

276Connecting plug with diagnostic LEDs for PROFIBUS DP

277PROFIBUS-DP cable, running meter

280Squirrel Cage Motor Basic 400/690/0.3

281Gear w.2 Switch Arms 0.1/0.3

282Ind. Proximity Switch 3-DC

283Coupling 0.1/0.3

284Coupling Guard 0.1/0.3

285STEP 7 Prof 2010 Single-licence -D,GB,F,E,I-

286Safety connecting leads, 32 A

287Safety connecting lead 32 A, yellow-green

288Mobile Experiment stand 1300

290Channel Three-Phase 1300/S

ASIMA Plant Simulator complete equipment set 291

Basic unit for system simulator ASIMA

Logic functions, basic level292

Logic basic functions293

Digital function modules294

Motor ON/OFF295

Reversing contactor296

Star-delta connection44

297Reversing star-delta connection

298Pendulum table control

299Dahlander circuit

300Motor with 2 windings

301Motor self-starter

302Transparent folder, 410 mm x 320 mm x 10 mm

Control systems, intermediate level303

Conveyor belt system304

Reactive-current compensation305

Heating control306

Running light307

Tablets machine308

Tank system309

Coal grinder310

Fan control311

Traffic light for road works312

Traffic lights313

Collecting belt conveyor314

Conveyor charging system

Control systems, advanced level315

Embossing machine316

Silo control317

Reactor318

Goods lift319

Pump control45

320Dirty-water pump system

321Monitoring of 3 pumps

322Pump system (pressure)

323Drinks machine

324Mixer

325Sequence control

Item 3.3.4


Trainer basic panel 327

Connecting adapter for power supply328

Documentation S7-software on CD-ROM -D329

Power supply PS 307 incl. power cord330

Micro Memory Card, 64 Kb, forS7-3xxC331

PC adapter for S7-300 USB332

Simatic S7-300, CPU 314C-2 DP compact333

Power supply 24 V DC, 6.5 A, for 230 V AC336

Decentralized periphery ET200S with 4 DI / 2 DO337

P Operator Panel OP77B incl. WinCC Flexible338

Frequency Inverter 300 W Micromaster 420339

PROFIBUS-Module for Micromaster 420 / 440340

Stripping tool for PROFIBUS-DP cable341

Connecting plug with diagnostic LEDs for PROFIBUS DP342

PROFIBUS-DP cable, running meter343

Squirrel Cage Motor Basic 400/690/0.3344

Gear w.2 Switch Arms 0.1/0.346


346Coupling 0.1/0.3




350Safety connecting lead 32 A, yellow/green

351Mobile Experiment stand 1300


T9.5.1.19 ASIMA Plant Simulator complete equipment set353



Logic basic functions355

Digital function modules356

Motor ON/OFF357

Reversing contactor358

Star-delta connection359

Reversing star-delta connection360

Pendulum table control361

Dahlander circuit362

Motor with 2 windings363

Motor self-starter364

Transparent folder, 410 mm x 320 mm x 10 mm




367Heating control

368Running light

369Tablets machine

370Tank system

371Coal grinder

372Fan control

373Traffic light for road works

374Traffic lights

375Collecting belt conveyor

376Conveyor charging system


Embossing machine378

Silo control379

Reactor380

Goods lift381

Pump control382

Dirty-water pump system383

Monitoring of 3 pumps384

Pump system (pressure)385

Drinks machine386

Mixer387

Sequence control


Trainer basic panel389

Connecting adapter for power48

390Documentation S7-software on CD-ROM

391Power supply PS 307 incl. power cord

392Micro Memory Card, 64 kB, for S7-3xxC

393PC adapter for S7-300 USB

394Simatic S7-300, CPU 314C-2 DP compact

395Power supply 24 V DC, 6.5 A, for 230 V AC

396Decentralized periphery ET200S with 4 DI / 2 DO

397P Operator Panel OP77B incl. WinCC Flexible

398Frequency Inverter 300 W Micromaster 420

399PROFIBUS-Module for Micromaster 420 / 440

400Stripping tool for PROFIBUS-DP cable

401Connecting plug with diagnostic LEDs for PROFIBUS DP

402PROFIBUS-DP cable, running meter

403Squirrel Cage Motor Basic 400/690/0.3

404Gear w.2 Switch Arms 0.1/0.3


406Coupling 0.1/0.3




410Safety connecting lead 32 A, yellow/green


ASIMA Plant Simulator complete equipment set T9.5.1.19412



413Logic basic functions

414Digital function modules

415Motor ON/OFF

416Reversing contactor

417Star-delta connection

418Reversing star-delta connection

419Pendulum table control

420Dahlander circuit

421Motor with 2 windings

422Motor self-starter

423Transparent folder, 410 mm x 320 mm x 10 mm




Heating control427

Running light428

Tablets machine429

Tank system430

Coal grinder431

Fan control432

Traffic light for road works433

Traffic lights434

Collecting belt conveyor435

Conveyor charging system


436Embossing machine

437Silo control

438Reactor

439Goods lift

440Pump control

441Dirty-water pump system

442Monitoring of 3 pumps

443Pump system (pressure)

444Drinks machine

445Mixer

446Sequence controlSensor technology with SPS 314C-2DP and Step 7 single-user license T 9.3.4A

447 Gear w.2 Switch Arms 0.1/0.3448 Limit Switch 1NO 1NC449 Ind. Proximity Switch 3-DC450 Cap. Proximity Switch 3-DC451 Motor with FCC 0.3452 SIMATIC S7-CPU 314C-2DP453 Step 7 Software454 Complete Step 7 Documentation (CD)455 S7 PC Adapter USB456 Profibus Connection Cable

AS-Interface with SPS 314C-2DP and S7 single-user license T 9.3.5A

457 Pushbutton, Threefold458 Signal Lamp 24V, Threefold459 AS-I Connection Module 2E/2A460 AS-I Set461 AS-I Bus Testing Instrument462 Profibus Cable463 DP / AS-I Communications Module464 COM3LAB Course: Operational Amplifier465 COM3LAB Course: Control Technology I

51

8.2.1.1 Temperature control466 PID Digital Controller467 Reference Variable Generator468 Digital Temperature Controlled System469 Two position controller470 Profi-CASSY Starter 2471 DC-Power Supply ± 15 V/3 A472 Safety Bridging Plugs, black473 Safety Bridging Plugs with Tap, black474 Safety connection lead 100 cm, red475 Safety connection lead 100 cm, blue476 Safety connection lead 100 cm, black477 WinFACT COM3LAB / CASSY Edition

Speed and Voltage control T 8.2.1.6

478 Reference Variable Generator479 PID Digital Controller480 Set of machines 10 W481 Profi-CASSY Starter 2482 DC-Power Supply ± 15 V/3 A483 safety bridging plugs, black484 Safety Bridging Plugs with Tap, black485 Safety connection lead 100 cm, red486 WinFACT COM3LAB / CASSY Edition487 Safety connection lead 100 cm, blue488 Safety connection lead 100 cm, black489 Mobile cable holder490 Panel frame VT180, Three Level491 TFT Monitor frame TPS492 Equipment Platform 500 mm493 Grooved mat cabinet 1200494 Shelf 1200495 Shelf 1200 with 1 grooved mat496 Shelf 1200 with 2 grooved mats497 Assembly set mussel-type handle

600 Synchronous generator T 11.1.1

601 Synchronous Machine SC 1.0602 Excitation Voltage Controller 200V/2,5 A603 Three-Phase Power Supply Unit with FCCB

52

604 Control Unit f. Pendulum Machine605 Pendulum Machine 1.0/2.0606 Coupling 1.0607 Shaft End Guard 1.0608 Coupling Guard 1.0609 Incremental Tacho 1.0610 Inductive Load 0.3/1.0611 Resistive Load 1.0612 Capacitive Load 1.0613 Safety bridging plugs, black614 Safety bridging plugs, yellow/green615 Safety connection lead 100 cm, red616 Safety connection lead 100 cm, blue617 Safety connecting leads, 32 A618 Safety connecting lead 32 A, yellow/green619 Moving Iron Meter 1 A620 Moving Iron Meter 2.5 A621 Multifunctional measuring instrument

Three-phase transformers T 11.2.1

622 Three-Phase Transformer TL380KVPower supplies/measurement tools

623 3-Phase Voltage 400 V/2.5 A624 Isolation Amplifier, Four Channel625 BNC cable, 1 m626 Safety bridging plugs, black627 Power Meter

Transmission Line Model 380 kV T 11.2.2

628 Transmission Line Model 380 kV, NET629 Transmission Line Capacitor TL380 kV630 Earth Fault Compensation631 Power Circuit Breaker Module632 Safety bridging plugs, black633 Safety connection lead 25 cm, black634 Transmission Line Model 380 kV, 90 km

Three-phase bus bar system T 11.2.5

635 Double Busbar636 Double Busbar Extension637 Power Circuit Breaker Module

53

638 Double Busbar Infeed/Outfeed639 Double Busbar Feeder Connector640 Double Busbar Feeder, Connector and Tap641 CASSY Lab 2642 Extra-Low Voltage 24/4643 Safety connection lead 10 cm, black644 Connecting lead 19 A, 50 cm, red/blue, pair645 Connecting lead 19 A, 100 cm, red/blue, pair646 Moving Iron Meter 2.5 A647 Moving Iron Meter 600 V

Current and voltage transformers T 11.3.1

648 Single-phase current transformer649 Load for Current Transformer650 Three-Phase Current Transformer651 Single-Phase Voltage Transformer652 Load for Voltage Transformer653 Three-Phase Voltage Transformer654 Summation Current Transformer655 Three-Phase Transformer TL380KV656 Three-Phase Supply Unit with FCCB657 Adjustable transformer 0...260 V, 4 A658 Resistive Load 1.0659 Safety bridging plugs, black660 Safety bridging plugs, yellow/green661 Safety connecting leads, 32 A662 Safety connecting lead 32 A, yellow/green663 Moving Iron Meter 1 A664 Moving Iron Meter 6 A665 Moving Iron Meter 100/400 V

Double busbar system T11.2.5.1 TG 17.140

666 Experimental stand Double busbar system667 Disc PLC programme for double bus bar system

Protective Relays T 11.3.2

668 Load L = 0.1-0.4 H; C = 2-16 µF669 Transmission Line Model 380 kV, NET670 3~ Time Over/undervoltage relay671 3~ Reverse power relay672 Power Circuit Breaker Module

54

673 3~ Time overcurrent relay (I)DMT674 3~ Directional Earth Fault Relay675 Safety bridging plugs, black676 Connecting lead 19 A, 100 cm, red/blue, pair677 USB/RS 485 interface convert678 Electronic Stopclock679 Acoustic Continuity Tester690 Multifunctional measuring instrument681 Software protection relay682 SCADA for protective relay

Reactive power compensation of an inductive load T 11.4.1

683 Switchable Capacitor Battery684 Reactive Power Controller685 Coupling 1.0686 Coupling Guard 1.0687 Control Unit 1.0688 Magnetic Powder Brake 1.0689 Squirrel Cage Motor 230/400 V 1.0

Multimeter690 Power Meter691 Power Factor Meter692 Moving Iron Meter 2.5 A

Power consumption measurement and peak load monitoring T 11.4.2

693 CASSY Lab 2694 Inductive Load 0.3/1.0695 Capacitive Load 1.0696 Mobile cable holder697 Sensor-CASSY698 Panel frame VT180, Three Level699 TFT Monitor frame TPS700 Equipment Platform 500 mm701 Grooved mat cabinet 1200702 Shelf 1200703 Shelf 1200 with 1 grooved mat704 Shelf 1200 with 2 grooved mats

Photovoltaic system – grid-connected system R2.1.3.1

705 DC switch disconnector706 Frequency Inverter PPI 600

55

707 Overload circuit breaker (ENS) for the Photovoltaic-system708 Power and Energy Meter A2000709 Overlay mask "photovoltaic"710 Mains feed from the photovoltaic system711 Set of connecting cables, black, 2.5 mm²712 TRMS Handheld Digital Multimeter 713 Insolation Meter SOL-MAC714 Rheostat 10 Ohm715 Rheostat 330 Ohm716 Mobile Solar Module carrier 2 PV generator717 Experiment Stand-M 1300, Mobile718 Connecting lead 19 A, 100 cm, red

Renewable Energies719 Connecting lead 19 A, 100 cm, black720 Wind Turbine Generator, mobile, full equipment set

R3.2.1.1721 Wind Power Plant; Mobile Experiment Stand722 Safety connection lead 10 cm, black723 Safety connection lead 25 cm, black724 Safety connection lead 50 cm, black725 Safety connection lead 100 cm, red726 Safety connection lead 100 cm, blue

Renewable Energies:727 Smart Grid Ready-to-go800801 1-PH. Transformer 0.3802 AC-Toroidal Core Transformer 0.3803 AC-Auto Transformer 0.3804 Resistive Load 0.3805 Capacitive Load 0.3806 Inductive Load807 Multimeter Metrahit Pro808 Power factor meter809 Sensor-CASSY 2 Starter810 Sensor-CASSY 2811 Adjustable transformer 0...260 V, 4 A812 3-Phase Voltage 400 V/2.5 A813 safety bridging plugs, black814 Safety bridging plugs, yellow/green815 Safety connecting leads, 32 A

56

816 Safety connecting lead 32 A, yellow/greenDC Machines 0.3E2.2.2.0

817 DC Compound Machine 0.3818 Universal Motor 0.3819 Starter 0.3820 Resistive Load 0.3821 On/Off Switch Three-Pole822 Power Circuit Breaker Module823 Field Regulator Motor 0.3824 Field Regulator Generator 0.3825 Machine Test System 0.3826 CBM10 MOMO / FCCP827 Multimeter Metrahit Pro828 DC engine supply 300 W829 Coupling 0.1/0.3830 Shaft End Guard 0.1/0.3831 Coupling Guard 0.3 kW, transparent832 safety bridging plugs, black833 Safety bridging plugs, yellow/green834 Safety connecting leads835 Safety connecting lead 32 A, yellow/green

AC Machines, 0.3E2.2.3.0

836 Capacitor Motor CS Basic 0.3837 Motor Protection Switch 1-1.6A838 Motor Protection Switch 1.6-2.4A839 On/Off Switch Three-Pole840 Power Circuit Breaker Module841 Machine Test System 0.3842 CBM10 MOMO / FCCP843 Multimeter Metrahit Pro844 Power factor meter845 Adjustable transformer 0...260 V, 4 A846 Coupling 0.1/0.3847 Shaft End Guard 0.1/0.3848 Coupling Guard 0.3 kW, transparent849 safety bridging plugs, black850 Safety bridging plugs, yellow/green851 Safety connecting leads, 32 A852 Safety connecting lead 32 A, yellow/green

57

853 Squirrel Cage Motor 0.3E.2.2.4.0

854 Slip Ring Motor 0.3855 Squirrel Cage Motor Basic 400/690/0.3856 Squirrel Cage Motor Basic 230/400/0.3857 Three-Phase Supply Unit with FCCB858 Motor Protection Switch 1-1.6A859 On/Off Switch Three-Pole860 Power Circuit Breaker Module861 Resistive Load 0.3862 Capacitive Load 0.3863 Star-delta switch864 Star-Delta Reversing Switch865 Reversing Switch866 Star Delta Starter867 Rotor Starter 0.3868 Machine Test System 0.3869 CBM10 MOMO / FCCP870 Multimeter Metrahit Pro871 Coupling 0.1/0.3872 Shaft End Guard 0.1/0.3873 Coupling Guard 0.3 kW, transparent874 safety bridging plugs, black875 Safety bridging plugs, yellow/green876 Safety connecting leads, 32 A877 Safety connecting lead 32 A, yellow/green878 E2.2.5.0 Synchronous Machine 0.3879 Synchronous Machine SP 0.3880 Resistive Load 0.3881 Capacitive Load 0.3882 Inductive Load883 Three-Phase Supply Unit with FCCB884 Manual Synchronisation Unit885 Motor Protection Switch 1-1.6A886 Power Circuit Breaker Module887 Multimeter Metrahit Pro888 Moving Iron Meter 2.5 A889 Power factor meter890 Machine Test System 0.3891 CBM10 MOMO / FCCP

58

892 DC engine supply 300 W893 DC-High Current Power Supp. 32/20894 Adapter sockets895 Coupling 0.1/0.3896 Shaft End Guard 0.1/0.3897 Coupling Guard 0.3 kW, transparent898 safety bridging plugs, black899 Safety bridging plugs, yellow/green900 Safety connecting leads, 32 A901 Safety connecting lead 32 A, yellow/green

Static Converter Drive with DC MachinesE2.5.2.1

902 Thyristor Speed Control Unit903 Tacho Generator 0.1/0.3904 DC Compound Machine 0.3905 Probe 100 MHz, 1:1 / 10:1906 Digital storage oscilloscope 722907 Adapter sockets908 Transformer 45/90, 3 N909 Function generator 200 kHz910 Plug-in power supply 12 V AC911 Coupling 0.1/0.3912 Shaft End Guard 0.1/0.3913 Coupling Guard 0.1/0.3914 safety bridging plugs, black915 Safety connecting leads, 32 A916 Safety connecting lead 32 A, yellow/green

Item 3.6.7Drives with Educational Frequency Converter

917 Universal Converter 3X230V918 Converter Input/Output919 Squirrel Cage Motor 230/400 V 0.3920 Control unit PWM921 BNC cable, 1 m922 Multimeter Metrahit Pro923 Probe 100 MHz, 1:1 / 10:1924 Digital storage oscilloscope 722925 Adapter sockets926 Isolation Amplifier, Four Channel927 Machine Test System 0.3928 CBM10 MOMO / FCCP

59

929 Adapter USB port/serial port930 RS-232 cable, 9-pole931 Panel frame T130, Two Level932 DC-Power Supply ± 15 V/3 A933 Single-Phase Supply Unit934 Coupling 0.1/0.3935 Shaft End Guard 0.1/0.3936 Coupling Guard 0.3 kW, transparent937 safety bridging plugs, black938 Safety connecting leads, 32 A939 Safety connecting lead 32 A, yellow/green

Item 3.6.8.E2.5.3.4 Drives with Industry Frequency Converter 0.3

940 Industrial Frequency Converter 300 W941 Squirrel Cage Motor 230/400 V 0.3942 Multimeter Metrahit Pro943 Machine Test System 0.3944 CBM10 MOMO / FCCP945 LCP2 Local Control Panel946 Panel frame T150, Two Level947 Coupling 0.1/0.3948 Shaft End Guard 0.1/0.3949 Coupling Guard 0.3 kW, transparent950 safety bridging plugs, black951 Safety bridging plugs, yellow/green952 Safety connecting lead 32 A, yellow/green953 Safety connecting leads, 32 A

Item 3.6.9.E2.6.2.1 AC Servo with Block Commutation

954 Reference Variable Generator955 Incremental Tacho 0.3956 Commutation Pick-Up 0.1/0.3957 AC Servo Motor 0.3958 Control Unit Block Commutation959 Converter Input/Output960 Universal Converter 3X230V961 BNC cable, 1 m962 Multimeter Metrahit Pro963 Probe 100 MHz, 1:1 / 10:1964 Digital storage oscilloscope 722965 Adapter sockets

60

966 Isolation Amplifier, Four Channel967 Machine Test System 0.3968 CBM10 MOMO / FCCP969 CBC 12.5 Servo technology970 Single-Phase Supply Unit971 DC-Power Supply ± 15 V/3 A972 Coupling 0.1/0.3973 Shaft End Guard 0.1/0.3974 Coupling Guard 0.3 kW, transparent975 safety bridging plugs, black976 Safety connecting leads, 32 A977 Safety connecting lead 32 A, yellow/green978 Adapter USB port/serial port979 RS-232 cable, 9-pole980 Connecting lead 19 A, 50 cm, red/blue, pair

Item 3.6.10E2.6.2.3 Position Servo Control

981 Reference Variable Generator982 Position Controller, digital983 Gear 0.3984 Potentiometrical Angle Transducer 0.1/0.3985 Incremental Tacho 0.3986 Commutation Pick-Up 0.1/0.3987 AC Servo Motor 0.3988 Control Unit Block Commutation989 Universal Converter 3X230V990 Converter Input/Output991 PID Digital Controller Net992 Software: Leylab.control Lite993 CBC 12.5 Servo technology994 Single-Phase Supply Unit995 DC-Power Supply ± 15 V/3 A996 safety bridging plugs, black997 Safety connecting leads, 32 A998 Safety connecting lead 32 A, yellow/green999 Multimeter Metrahit Pro1000 RS-232 cable, 9-pole1001 Adapter USB port/serial port1002 Shaft End Guard 0.1/0.31003 Coupling Guard 0.3 kW, transparent

61

1004 Coupling 0.1/0.3Additional accessories:

1005 Mobile cable holder1006 Panel frame VT180, Three Level1007 TFT Monitor frame TPS1008 Equipment Platform 500 mm1019 Grooved mat cabinet 12001010 Shelf 12001011 Shelf 1200 with 1 grooved mat1012 Shelf 1200 with 2 grooved mats1013 Assembly set mussel-type handle

62

5. LIST OF LITERATURE

List of educational literature from publishers of the Federal Republic of Germany in English

№ Name Author Publisher Edition ISBN code

Place of publication

Year of publication

Discipline (s)/module(s) where will be used

Quantity Comments

(1) Electrical Engineering - Tables, Standards, Formulas

Europa-Lehrmittel

2nd

30337Haan-Gruiten

2015 2.1 – 2.53.1 - 3.25.18.2 - 8.39.1 - 9.511.116.1 - 16.217.1 – 17.519.123.1 - 23.224.1

24 Materials,Connecting technology, Environmental technology, Technical communication, Electrical systems, Control systems, Electric motors, Digital technology, Computer technology, Components, Modules, Measurement, Mathematics, Physics, Circuit theory, Costs

64



Year of publication


Quantity Comments

(2) Formula HandbookElectrical Trades (Power Engineering)

Dr. Christiani 2nd

100144Konstanz 2006 2.1 – 2.5

3.1 - 3.25.18.2 - 8.39.1 - 9.511.116.1 - 16.217.1 – 17.519.123.1 - 23.224.1

24 General advice, General principles, Geometry, Solid geometry, Physical calculations, Transmission ratio calculations, General principles of electricity, Magnetic field, Electric field, Basic quantities of an alternating-current circuit, Calculators in an alternating-current circuit, Three-phase alternating current, Feeder calculation,

65



Year of publication


Quantity Comments

Electrical machines, Electronics, Tables

(3) Electricity - Electrostatics

LD Didactic 589162EN

Hürth 2.1 2 59 experiments in 29 students' worksheets.120 pages, DIN A4, in English

(4) Basic electric circuits

LD Didactic 58834EN

Hürth 2.1 2 19 experiments using the STE plug-in system. Teachers' section with solutions and copyable templates for student worksheets, in ring binder with CD, approx. 170 pages.In English.Topics:Circuits and switchesElectrical

66



Year of publication


Quantity Comments

measuring techniquesOhmic resistanceVoltage sourcesApplied electric circuits

(5) DC Circuits LD Didactic 565622EN

Hürth 2.1 2 30 experimental arrangements for exercises and demonstration with solutions. DIN A4 in English

(6) Electricity, Electromagnetism

LD Didactic 58835EN

Hürth 2.1 2 17 experiments using the STE plug-in system. Teachers' section with solutions and copyable templates for student worksheets, in ring binder with CD, approx. 160 pages. In

67



Year of publication


Quantity Comments

EnglishTopics:ElectromagnetismElectromagnetic applicationsInductionTransformersTechnical applications for inductionCoils and capacitors

(7) Three-phase transformers and three-phase transformer circuits


Hürth 2.1 2 DIN A4, in English,additionally required: PC with Windows 7/8

(8) Electrical Motor & Generator. Mod. B


Hürth 2.1 2 29 experiment descriptions for demonstrationand students work on the "physical processesand

68



Year of publication


Quantity Comments

characteristics of large machines";134 pages, A4 size; in Englishadditionally required: PC with Windows 7/8

(9) Discrete Components and Basic Circuits of Electronics


Hürth 2.1 2 28 experiments, with an introduction to the equipment. DIN A4, in English

(10) Protection measures VDE 0100 EN

Elwe-Technik 8-5114012-000-10-0

Via LD Didactic, Hürth

2.1 - 2.2,5.1

2

(11) Installation circuits with switches

Elwe-Technik 8-5304112-100-10-0


2.2,5.1

2

(12) Safety Measures according to DIN VDE 0100 and DIN VDE


Hürth 2.2,5.1

2 70 illustrations and diagrams, 122 pages, DIN A4

69



Year of publication


Quantity Comments

0701 with the Test and Fault Simulator

Language: EnglishTopics:Basic testing, measuring and fault location exercises Tests as per DIN VDE 0100 – 610Tests as per DIN VDE 0701

(13) Booklet Automation system S7-300, starter pack,

Elwe-Technik 8-5212012-000-10-0


8.211.117.219.1

2 Manual "Automation System S7-300 ENGetting Started Collection:- CPU 314 C: Positioning with Analog output- CPU 314 C: Positioning with Digital output- CPU 31x C: Start-up- CPU 31x C: Control

70



Year of publication


Quantity Comments

- CPU 31x C: Point-to-point-coupling- CPU 31x C: CountingReference Manual: CPU DataReference Manual: Module DataInstallations Manual: AssemblyManual: CPU 31x C Technological Functions incl. CD with examplesOperations list: CPU DataPaper version

(14) System simulations control

Elwe-Technik 8-5212641-000-10-0


8.29.511.117.219.1

2 German language onlySteuerung von Anlagensimulationen

71



Year of publication


Quantity Comments

(15) Control of system simulations

Elwe-Technik 8-5212642-000-10


8.29.511.117.219.1

2 English version

(16) Complete Step 7 Documentation (CD)

Siemens 730880 Via LD Didactic, Hürth

8.211.117.219.1

2 The complete documentation and Step 7 reference manual are available in German, English, French, Spanish and Italian on CD,Maybe also in Russian

(17) Control of Technical Lines I

LD Didactic 56424EN

Hürth 8.211.117.219.1

2 Detailed representation of experiments to Control of technical Lines I, included results for the teacher and measurements

72



Year of publication


Quantity Comments

with CASSY Lab 2. DIN A4, in English.Items:- Temperature Control- Liquid: Flow – Measurement & Control- Liquid Level: Measurement & Control- Gas flow control

(18) Control of Technical Lines II

LD Didactic 56425EN

Hürth 8.211.117.219.1

2 Detailed representation of experiments to Control of technical Lines II, includes results for the teacher and measurements with CASSY Lab 2. DIN A4, in English.Speed and Voltage control

73



Year of publication


Quantity Comments

(Machine 10 W)

(19) Synchronous generator and synchronization circuits T 11.1.1 & T 11.1.2


Hürth 8.211.117.219.1

2 Theoretical fundamentals, equipment descriptions, experiment instructions, discussion of the results. In English

(20) Three-Phase Transformer T 11.2.1


Hürth 8.211.117.219.1

2 Theoretical fundamentals, equipment descriptions, experiment instructions, discussion of the results. DIN A4, in English

(21) Transmission Line Model 380 kV, T 11.2.2


Hürth 8.211.117.219.1

2 Theoretical fundamentals, equipment descriptions, experiment instructions, discussion of the results.DIN A4, in

74



Year of publication


Quantity Comments

English(22) Three-Phase

Bus-Bar System T 11.2.5


Hürth 8.211.117.219.1

2 Basic information, exercises for the student and solutions for the teacher.DIN A4, in English

(23) Current & Voltage Transformers, Part 1; T 11.3.1


Hürth 8.211.117.219.1

2

(24) Double busbar system

Elwe-Technik 8-5117042-000-10-1


8.211.117.219.1

2 In English

(25) Protective Relays T 11.3.2


Hürth 8.211.117.219.1

2 Relays for Power System Protection.Theoretical fundamentals, equipment descriptions, experiment instructions, discussion of the results. DIN A4,

75



Year of publication


Quantity Comments

in English(26) Reactive Power

Compensation of an Inductive Load, T 11.4.1


Hürth 8.211.117.219.1

2 Theoretical fundamentals, equipment descriptions, experiment instructions.DIN A4, in English

(27) Power Consumption Measurements T 11.4.2


Hürth 8.211.117.219.1

2 Theoretical fundamentals, equipment descriptions, experiment instructions.DIN A4, in English

(28) Photovoltaic system mains coupled


Hürth 8.211.117.219.1

2 Theoretical fundamentals, Equipment descriptions, Experiment instructions.DIN A4, in German only

76



Year of publication


Quantity Comments

(29) Wind power plant

Elwe-Technik 8-5117102-000-10-1


8.211.117.219.1

2 in English

(30) Transformers T 10.1


Hürth 2.13.15.1

2 54 illustrations and diagrams, 56 pages, DIN A4Language: EnglishTopics:Experiments with the single-phase transformerExperiments with the single-phase toroidal core transformerExperiments with the single-phase autotransformerExperiments with the three-phase transformer

77



Year of publication


Quantity Comments

Experiments with the Scott transformerPractice questions

(31) DC Machines T 10.2.1


Hürth 2.13.15.1

2 93 illustrations and Diagrams, 130 pages, DIN A4Language: EnglishTopics:Experiments with the shunt wound machineExperiments with the series wound machineExperiments with the compound wound machineExperiments with the DC multifunction machineExperiments with the

78



Year of publication


Quantity Comments

universal motorrefresher Questions

(32) AC Machines T 10.3.1 Instructor's Edition


Hürth 2.13.15.1

2 52 illustrations and diagrams, 86 pages, DIN A4Language: English Topics: Experiments with the universal motor Experiments with the capacitor motor F capacitor motor R Experiments with the bifilar-wound motor F bifilar-wound motor R Repulsion motor Refresher Questions

79



Year of publication


Quantity Comments

(33) Asynchronous Machines T 10.4.1


Hürth 2.13.15.1

2 90 illustrations and diagrams, 118 pages, DIN A4Language: EnglishTopics:Experiments with the 400 / 690 V squirrel cage motor230 / 400 V squirrel cage motorSquirrel cage motor with a Dahlander windingSeparate-winding squirrel cage motorSlip ring motorMultifunction machineSquirrel cage fault simulatorAsynchronous

80



Year of publication


Quantity Comments

machine Practice Questions

(34) Synchronous Machines T 10.4.2


Hürth 2.13.15.1

2 43 illustrations and diagrams, 80 pages, DIN A4Language: EnglishTopics:Experiments with the synchronous machine with smooth core rotor;Synchronous machine with Salient Pole Rotor;Multifunction Machine;Reluctance Motor;Practice Questions

81



Year of publication


Quantity Comments

(35) Power Electronics and Drive Technology, T 12.3.2


Hürth 2.13.15.1

2 Compact static converter-fed D.C. machines.Basic theoretical information, equipment descriptions, experiment instructions.DIN A4, in English



Hürth 2.13.15.1

2 Frequency converter technology drives.Basic theoretical information, equipment descriptions, experiment instructions.In English

(37) Industry Invert. Drive 0.3 E2.5.3.4


Hürth 2.13.15.1

2 In English

82



Year of publication


Quantity Comments



Hürth 2.13.15.1

2 AC Servo with block commutation. Basic theoretical information, equipment descriptions, experiment instructions.In English



Hürth 2.13.15.1

2 Position Servo Control.Basic theoretical information, equipment descriptions, experiment instructions.In English

(40) Electrical Drives: Principles, Planning, Applications, Solutions

Weidauer, Messer

Publicis Publishing

1st 978-3895784347

Erlangen 2014 2.1 - 2.5,3.1 - 3.28.2 - 8.39.1 - 9.516.1 - 16.2 17.1 - 17.5,24.1

24 covers all aspects of modern electrical drives

83



Year of publication


Quantity Comments

(41) Planning Manual for Power Distribution Plants Design, Implementation and Operation of Industrial Networks

Kiank, Fruth (Siemens)

Publicis Publishing

1st 978-3895783715

Erlangen 2011 2.2, 3.29.1, 9.4, 9.516.1 -16.217.2, 17.424.1

2 This book is intended for engineers and technicians of the energy industry, industrial companies and planning departments. It provides basic technical network and plant knowledge on planning, installation and operation of reliable and economic industrial networks. In addition, it facilitates training for students and graduates in this field.

84



Year of publication


Quantity Comments

(42) Training Concept Control - Cabinet Basic Module Workbook for lecturer

Dr. Christiani 3rd

93366Konstanz 2012 2.1 - 2.2

5.18.211.116.1 -16.224.1

2 1. Analysing electrotechnical systems and testing functions2. Planning and carrying out electrical installations3. Analysing and adapting control systems

(43) Switch Cabinet Training Concept – Basic ModuleDocumentation for Student/Trainee

Dr. Christiani 3rd

93367Konstanz 2011 2.3

5.111.1

24

(44) Practical Guide to Inspection, Testing and Certification of Electrical Installations

Christopher Kitcher

Routledge 3rd 978-0080969077

London, New York

2013 3.1, 3.38.39.317.519.1

2

(45) Electrical Installation

Christopher

Routledge 9th 978-041581

Abingdon, Oxon

2013 2.1-2.55.1

4 Reference bookA step by step

85



Year of publication


Quantity Comments

Calculations: Basic; for technical certificate level 2

Kitcher 0043 8.1-8.39.1-9.511.1

guide to everyday calculations used on the jobEssential aid to the City & Guilds certificates Levels 2 & 3For apprentices and electrical installation engineers

(46) Electrical Installation Calculations: Advanced; for technical certificate and NVQ level 3

Christopher Kitcher

Routledge 8th 978-0415810036

Abingdon, Oxon

2.1-2.55.18.1-8.39.1-9.511.119.124.1

2

(47) BTEC National Further Mathematics for Technicians Third Edition

Graham Taylor/Alex Greer and Partners

Oxford University Press

2nd 978-0748794102

2005 5.111.119.124.1

2 - BTEC - vocational qualification taken in UK, equivalent to A Levels- provides all of the needed

86



Year of publication


Quantity Comments

materials for students taking the further mathematics optional unit of BTEC National Engineering and Electronics courses

(48) Level 3 NVQ Diploma in Electrotechnical Technology 2357 Units 301-304

The IET & City & Guilds

1st 978-0851932781

2014 2.1-2.5, 3.1-3.3, 5.1,8.1-8.3,9.1-9.5, 11.1

2 - NVQ = national vocational qualification

(49) Level 3 NVQ Diploma in Electrotechnical Technology 2357 Unit 309 Textbook (vocational)


1st 978-0851932811

2013 2.1-2.5, 3.1-3.3, 5.1,8.1-8.3,9.1-9.5, 11.1

2

(50) Level 3 NVQ in Electrotechnical Technology 2357 Units 307-308 Textbook (vocational)


1st 978-0851932804

2013 2.1-2.5, 3.1-3.3, 5.1,8.1-8.3,9.1-9.5, 11.1

2

87



Year of publication


Quantity Comments

Editions in English(51) Electric Power

Generation, Transmission, and Distribution

Leonard L. Grigsby

CRC Press Taylor & Francis Group

2nd 10: 0849392926

New York

2007 2.4 2 Part of the second edition of The Electric Power Engineering Handbook, Electric Power Generation, Transmission, and Distribution offers focused and detailed coverage of all aspects concerning the conventional and nonconventional methods of power generation, transmission and distribution systems, electric power utilization, and power quality. Contributed to

88



Year of publication


Quantity Comments

by worldwide leaders under the guidance of one of the world's most respected and accomplished authorities in power engineering, this carefully crafted reference provides convenient access to both overviews and detailed information on a diverse array of topics.

(52) Switching in Electrical Transmission and Distribution Systems

Smeets R., Van Der Sluis L., Kapetanovic M.,

Wiley 1st 10: 1118381351.

2014 Chichester 2.1 - 2.5, 3.2 - 3.3, 9.3 - 9.4, 19.1

2 The book systematically discusses the electrical aspects of switching, details the way load and fault

89



Year of publication


Quantity Comments

Peelo D.F., Janssen A.

currents are interrupted, the impact of fault currents, and compares switching equipment, in particular circuit–breakers. The authors also explain all examples of practical switching phenomena by examining real measurements from switching tests.

(53) Dirty Electricity : Electrification and the Diseases of Civilization

Samuel Milham

iUniverse 2nd 193890818X

2012 New York 2.1 2 Dirty Electricity tells the story of Dr. Samuel Milham, the scientist who first alerted the world about the frightening link between

90

http://www.bookdepository.com/publishers/iUniverse



Year of publication


Quantity Comments

occupational exposure to electromagnetic fields and human disease. Milham takes readers through his early years and education, following the twisting path that led to his discovery that most of the twentieth century diseases of civilization, including cancer, cardiovascular disease, diabetes, and suicide, are caused by electromagnetic field exposure.

91



Year of publication


Quantity Comments

(54) Power Systems. Electric Power Engineering Handbook

Grigsby L.L.

Taylor & Francis Group

2nd 0849392888

2006 New York 2.1 - 2.4, 3.3, 9.3, 16.2

2 The generation, delivery, and utilization of electric power and energy remain one of the most challenging and exciting fields of electrical engineering. The astounding technological developments of our age are highly dependent upon a safe, reliable, and economic supply of electric power. The objective of the Electric Power Engineering Handbook, 2nd edition, is to provide a contemporary

92



Year of publication


Quantity Comments

overview of this far-reaching field as well as to be a useful guide and educational resource for its study.

(55) Safety Differently: Human Factors for a New Era

Sidney Dekker

Apple Academic Press Inc.

2nd 1482241994

Oakville, Canada

2014 2.1 - 2.4, 3.1 - 3.3, 9.1- 9.4, 17.2, 17.4, 17.5, 19.1 - 19.2, 23.2 - 23.3., 24.1

2 Today, the unrelenting pace of technology change and growth of complexity calls for a different kind of safety thinking. Automation and new technologies have resulted in new roles, decisions, and vulnerabilities whilst practitioners are also faced with new levels of

93



Year of publication


Quantity Comments

complexity, adaptation, and constraints. It is becoming increasingly apparent that conventional approaches to safety and human factors are not equipped to cope with these challenges and that a new era in safety is necessary. In addition to new material covering changes in the field during the past decade, the book takes a new approach to discussing safety.

(56) Fundamentals of Electric Power

Mayergoyz

World Scientific

1st 978-981-

2014 Singapore 2.4, 3.1 - 3.3,

4 Electric power engineering has

94



Year of publication


Quantity Comments

Engineering I.D., McAvoy P.

Publishing Company

4616-58-4

9.3, 16.2,

always been an integral part of electrical engineering education. Providing a unique alternative to existing books on the market, this text presents a concise and rigorous exposition of the main fundamentals of electric power engineering. Contained in a single volume, the materials can be used to teach three separate courses — electrical machines, power systems and power electronics,

95



Year of publication


Quantity Comments

which are in the mainstream of the electrical engineering curriculum of most universities worldwide.

96

List of educational literature from publishers of the Federal Republic of Germany in German language

№ Name Author Publisher Edition number

ISBN code


Year of publication


Quantity Comments

Course books(57) Fachkunde

Elektroberufe. Elektroniker für Energie- und Gebäudetechnik, Betriebstechnik, Automatisierungstechnik

Josef Elpers/Norbert Meyer/Felix Ruwe et al.

Bildungsverlag EINS

4th 978-3-8242-4290-0

2013 2.1-2.4,3.39.5,17.2,19.123.1

1 Student’s edition

(58) Elektroniker für Energie- und Gebäudetechnik, Betriebstechnik, Automatisierungstechnik

Rasit Özgüc

Bildungsverlag EINS

1st 978-3-427-04292-1

2008 9.5, 17.2,19.1,23.1

1 Exercise bookDifferent types of tasks and learning situations

(59) Elektroniker für Energie- und Gebäudetechnik, Betriebstechnik,

Rasit Özgüc

Bildungsverlag EINS

1st OD342704293

2012 2.1-2.4,3.3,9.5,17.2,

1 Solutions for the exercises in the book Elektroniker für Engergie- und Gebäudetechnik,

97


ISBN code


Year of publication


Quantity Comments

Automatisierungstechnik

19.1,23.1

Betriebstechnik, Automatisierungstechnik

(60) Kernqualifikationen Elektrotechnik: Lernfelder 1-4

Markus Hüging/Josef Kuse/Nico Nordendorf

Bildungsverlag EINS

3rd 978-3427500001

2011 2.1-2.5,3.1-3.3,5.1-5.2,8.1-8.3,9.1-9.511.1-11.2

1 Conveys basic and expert knowledgeLearning fields 1 to 4Includes learning situations and projects taken from the daily routine of a model companyExercises

(61) Fachqualifikationen Elektrotechnik: Betriebstechnik Lernfelder 5-13

Markus Hüging/Josef Kuse/Nico Nordendorf et al.

Bildungsverlag EINS

2nd 978-3-427-50004-9

2009 16.1-16.2,17.1-17.5,19.1-19.2,23.1-23.3,24.1-24.2

1 Learning fields 5 to 13Contains learning situations and projects Over 300 exercise taskTakes into account regenerative energy sources such as wind power, photovoltaic and fuel cells

(62) Fachqualifikationen Elektrotechnik:

Bildungsverlag EINS

2nd 978-3-427-50007-0

2009 16.1-16.2,17.1-

1 Exercises that deepen the expert knowledge conveyed by the book

98


ISBN code


Year of publication


Quantity Comments

Betriebstechnik Lernfelder 5-13. Aufgabenband

17.5,19.1-19.2,23.1-23.3,24.1-24.2

Fachqualifikationen Elektrotechnik: Betriebstechnik Lernfelder 5-13

(63)4

Fachqualifikationen Elektrotechnik: Betriebstechnik Lernfelder 5-13. Lösungen auf –CD-ROM

Bildungsverlag EINS

2nd 978-3-427-50008-7

2009 16.1-16.2,17.1-17.5,19.1-19.2,23.1-23.3,24.1-24.2

1 CD-ROM with solutions of the exercises in the book Fachqualifikationen Elektrotechnik: Betriebstechnik Lernfelder 5-13 Aufgabenband

(64) Elektroberufe. Lernfeld 9: Gebäudetechnische Anlagen ausführen und in Betrieb nehmen

Gernot Besant

Bildungsverlag EINS

1st 978-3-427-44465-7

2005 2.4, 3.3, 9.2-9.3

1 Student’s editionLearning field 9 with examplesBuilding technology

(65) Elektroberufe. Lernfeld 10:

Karsten Block

Bildungsverlag EINS

1st 978-3-427-

2006 2.4, 9.4,

1 Student’s editionLearning field 10 examples

99


ISBN code


Year of publication


Quantity Comments

Energietechnische Anlagen errichten und in Stand halten

44461-9 17.4 Electrical devices, IT systems, aviation systems

(66) Elektroberufe Lernfeld 11: Automatisierte Anlagen in Betrieb nehmen und in Stand halten

Ludwig Schulze Everding

Bildungsverlag EINS

1st 978-3-427-44457-2

2007 17.2, 19.1, 23.1

1 Student’s editionLearning field 11 examplesSet up and maintain automation systems

(67) Automatisierungstechnik, Betriebstechnik, Mechatronik Lernfelder 1-6

Stefan Manemann/Jochen Rengstorf

Bildungsverlag EINS

2nd 978-3-427-44501-2

2010 17.2, 19.1, 23.1

1 Exercise bookSix practical projects with operating plans and about 150 exercisesIs geared to real plants and orders (partly in English language)Enables the simulation of a plant via Siemens SIMIT SCEOffers special advice concerning work techniques and methodsBoosts social competences (team work, presentations

100


ISBN code


Year of publication


Quantity Comments

etc.)DVD with project data, documentations, software, videos and pictures

(68) Automatisierungstechnik, Betriebstechnik, Mechatronik. Projekte für Lernfelder 1-6. Lösungen

Bildungsverlag EINS

2nd OD342744502

2012 17.2, 19.1, 23.1

1 Solutions for the exercises in the book Automatisierungstechnik, Betriebstechnik, Mechatronik Lernfelder 1-6

(69) Automatisierungstechnik, Betriebstechnik, Mechatronik Lernfelder 7-13

Stefan Manemann/Jochen Rengstorf

Bildungsverlag EINS

1st 978-3-427-44503-6

2008 17.2, 19.1, 23.1

1 Exercise bookOne operating plan for each projectTasks on different difficulty levelsOffers special advice concerning work techniques and methodsBoosts social competences (team work, presentations etc.)DVD with project data, documentations, software, videos and pictures

101


ISBN code


Year of publication


Quantity Comments

(70) Automatisierungstechnik, Betriebstechnik, Mechatronik. Projekte für die Lernfelder 7-13. Lösungen

Bildungsverlag EINS

1st OD342744504

2012 17.2, 19.1, 23.1

1 Solutions for the exercises in the book Automatisierungstechnik, Betriebstechnik, Mechatronik Lernfelder 7-13

(71) Fachwissen Betriebs- und Antriebstechnik. Betriebs-, Maschinen- und Antriebstechnik

Hartmut Fritsch/Heinz Häberle/Gregor Schmitt

Europa-Lehrmittel

7th 978-3-8085-5007-6

2015 3.1, 9.1., 9.4,16.2,17.2, 17.4, 19.1,23.2

1 Basic and specialist knowledge for electronics technicians in the fields of industry and craftsDetailed treatment of power supply and plantsCD-ROM with pictures

(72) Elektronik Grundwissen. Berufliche Bildung für die Elektroberufe

Günther Buchholz/Elmar Dehler/ Bernhard Grimm et al.

Europa-Lehrmittel

15th 978-3-8085-3206-5

2010 2.1-2.5, 3.1-3.3, 5.1

1 Reference book for electronic basics

102


ISBN code


Year of publication


Quantity Comments

(73) Arbeitsblätter und Aufgaben Grundbildung Lernfelder 1-4. Technische Kommunikation Elektrotechnik

Europa-Lehrmittel

5th 978-3-8085-3575-2

2014 2.1-2.5,3.1-3.3,5.1-5.2,8.1-8.3,9.1-9.511.1-11.2

1 Exercise sheets for the learning fields 1 to 4Technical communication, electrotechnologyHeadlines in German and English

(74) Arbeitsblätter und Aufgaben Fachbildung Lernfelder 5-12. Technische Kommunikation Elektrotechnik

Europa-Lehrmittel

5th 978-3-8085-3595-0

2014 16.1-16.2,17.1-17.5,19.1-19.2,23.1-23.3,24.1-24.2

1 Exercise sheets for the learning fields 5 to 12Technical communication, electrotechnologyHeadlines in German and English

(75) Elektrotechnik Grundwissen: Lernfelder 1-4

Heinrich Hübscher/Jürgen Klaue/Mike Thielert

Westermann Schulbuch

4th 978-3142215327

2015 2.1-2.5,3.1-3.3,5.1-5.2,8.1-8.3,9.1-9.511.1-11.2

1 Student’s edition Learning fields 1-4

103


ISBN code


Year of publication


Quantity Comments

et al.(76) Elektrotechnik –

Betriebstechnik: Lernfelder 5-13


1st 978-3142221328

2009 17.2, 19.1, 23.1

1 Student’s edition Industrial engineeringLearning fields 5-13

(77) Elektrotechnik Aufträge: Betriebstechnik Lernfelder 9-13

Michael Dzieia/Heinrich Hübscher/Dieter Jagla et al.


1st 978-3142219332

2010 17.2, 19.1, 23.1

1 Student’s editionIndustrial engineeringLearning fields 9 to 13

Books for examinations and exam preparation(78) Der

Einstellungstest/Eignungstest zur Ausbildung zum Elektroniker, Elektroniker für Betriebstechnik, IT-System-Elektroniker, Elektroniker für Geräte und

Kurt Guth/Marcus Mery

Ausbildungspark

2nd 978-3-95624-035-5

2015 Information for staff on how to choose students

1 Exercises and solutions for students that help them prepare for aptitude tests (electronics technician, electronic technician for IT systems, devices and systems) Includes details of examination areasEnables a realistic simulation of the

104


ISBN code


Year of publication


Quantity Comments

Systeme examination situation with five exemplary examination sheets, a panoply of original examination questions, commented solutions

(79) Prüfungsbuch Elektrotechnik

Horst Bumiller

Europa-Lehrmittel

18th 9783808535684

2015 5.1,11.1,19.1,24.1

1 Preparation for final examination part 1 and part 2 Question-answer formatExam examples with detailed solutions

105

List of educational literature from publishers of the Russian Federation


ISBN code


Year of publication


Quantity Comments

(80) Electrical equipment of electrical power stations and substations

Gaysarov R. Korzhov A.

South Ural State University

1st - Chelyabinsk

2004 2.1, 2.2, 2.4,9.4, 17.4

4 Handbook is used for performing tasks on the courses “Power production”, “Electrical stations and substations”, “Power plants and substations, power supply systems”

(81) Electrical power stations and substations

Chumburidze D.

“Terek”1st - Vladikav

kaz2014 2.1, 2.2,

2.4, 2.59.4, 17.4

4 Textbook for students in “Power and Electrical Engineering”

(82) Relay protection and automation of electric power systems.

Kireyeva E .

Academy 4th 978-5-4468-0830-4

Moscow 2014 2.1, 2.2, 17.2, 19.1, 23.1

4 The textbook can be used for professional module PM.02 “Operation of electrical power stations, networks and systems” (MDK.02.02), specialty

106


ISBN code


Year of publication


Quantity Comments

140407 “Electric stations, networks and systems”.For students of secondary vocational education.

(83) Electrical substations

Sibikin Y.

Radiosoft 2nd 978-5-93037-279-3

Moscow 2014 2.4,19.1,24.1

4 Overview of the operating modes of electric systems and substations; methods of calculating the short-circuit current and the choice of electrical substations and power grids, the classification of substations are described.The manual may be useful to students of secondary vocational education.

(84) Installation of electrical equipment. Reference book

Kisarimov R.

Radiosoft 1st 978-5-93037-245-8

Moscow 2014 2.1, 2.2, 2.4, 9.4, 17.4

4 The reference book contains general necessary information for the production of electrical installation works, including a new model of modern electrical equipment.

107


ISBN code


Year of publication


Quantity Comments

(85) Commissioning of electrical equipment

Kisarimov R.

Radiosoft 1st 978-5-93037-268-7

Moscow 2014 2.3,3.1-3.29.2, 9.4,17.2, 17.4,19.1,23.2

4 The handbook provides information about the setting up of electrical devices, electrical machines and other elements and devices and electrical circuits operating at a voltage of up to 1000 V. The handbook is intended for electricians, whose work is related to the repair, adjustment and maintenance of electrical equipment.


Butyrskiy V.

In-Folio 1st 978-5-903826-47-6

Volgograd

2011 2.3, 3.1 - 3.2,9.2, 9.4,17.2, 17.4, 19.1, 23.2

4 Methods of inspections and tests of power electrical equipment, electrical apparatus and devices. Describes the device to be put into operation and used in the adjustment works. The volume and rate of testing of certain types of electrical equipment are given. Given information on the organization and

108


ISBN code


Year of publication


Quantity Comments

carrying out of commissioning. Textbook for specialized secondary vocational institutions

(87) Electrical and electromechanical equipment. General industrial machinery and household appliances

Sokolova E.

Academy 9th 978-5-4468-0479-5

Moscow 2007 2.2, 2.4,8.2,9.2,17.3

4 Electrical household arrangements described, the control circuit of electromechanical kitchen appliances, vacuum cleaners, washing machines, power tools are given. For students of secondary vocational education

(88) Technology of electric installation works

Mysyanov A., Nesterenko V.

Academy 1st - Moscow 2007 2.2, 2.4,8.1,9.2

4 Materials on the course Technology of electric installation works to prepare workers for the electrotechnical industry.For students of primary vocational education, electrical profile.

109


ISBN code


Year of publication


Quantity Comments

(89) Modes of operation of electric power stations equipment

Pushko A.

Vyatka State University

1st - Kirov 2003 2.2-2.5,3.2-3.3, 8.1, 9.4

4 Contains basic information about plants, power systems and generators in power plants.

(90) Electrical equipment of electrical power stations and substations of industrial enterprises

Seliverstov G.

Gomel State Technical University after B. Sukhoi

1st - Gomel 2011 2.1 - 2.4, 9.4, 17.4,

4 The manual covers the main equipment of power plants and substations, circuit power stations and substations, including the main circuit, the circuit switching, control panels and other elements stations and substations.

(91) Reference book for electrician to repair electrical equipment of industrial plants

Sibikin Y.

Radiosoft 1st 978-5-93037-190-1

Moscow 2010 16.1, 17.1, 17.5, 19.1 - 19.2, 23.2, 24.1

2 The book contains background information on how to repair basic electrical equipment - electrical machines, welding transformers, solenoids, oil power transformers, ballasts and power cables. The book is intended for students of engineering and for the teaching staff of

110


ISBN code


Year of publication


Quantity Comments

educational institutions of vocational training. Prepares workers for electrical professions.

(92) Maintenance and repair of electrical equipment and networks of industrial plants

Sibikin Y.

Directmedia 8th 978-5-4458-8891-8

Moscow-Berlin

2014 16.1, 17.1, 17.5, 19.1 - 19.2, 23.2, 24.1

4 Contains general information on the materials, instruments, tools and mechanisms used by electricians on repair and maintenance of electrical networks and industrial plants. The textbook intended for students of vocational schools

(93) Electrical safety for electrical installations of industrial plants

Sibikin Y.

Academy 1st 978-5-4468-0655-3

Moscow 2014 2.1, 2.2, 2.4, 3.1-3.3,8.1-8.2, 9.1-9.4, 16.2, 17.2, 17.4 - 17.5,

4 Considers:-Causes of high danger when working on electrical installations, used electrical safety means-Standards OSSS and safety regulations-Organizational and technical measures to ensure

111


ISBN code


Year of publication


Quantity Comments

19.1, 23.2 -23.3,24.1

the safe operation of staff-maintain and repair electrical industrial equipmentThe textbook intended for students of vocational schools.

(94) Work safety during installation, maintenance and repair of electrical equipment for enterprises. Reference book

Sibikin Y.

KnoRus 1st 978-5-406-00277-3

Moscow 2011 2.1, 2.2, 2.4, 3.1-3.3,8.1-8.2, 9.1-9.4, 16.2, 17.2, 17.4 - 17.5, 19.1, 23.2 -23.3,24.1

4 Describes the requirements for electrical engineering personnel, tools, appliances and lifting equipment, personal protective equipment, measures for first aid to victims of the electrical effects.

(95) Installation, maintenance and repair of electrical equipment at

Sibikin Y.

Directmedia 1st 978-4458-5745-7

Moscow-Berlin

2014 2.2-2.5, 3.2-3.3, 9.3-9.4, 16.1,17.2,

4 The methods and techniques of installation, operation, repair of electrical equipment and electrical networks of industrial

112


ISBN code


Year of publication


Quantity Comments

industrial installations. Textbook

17.5, 19.1,23.2,24.1,

enterprises are considered. For students of primary vocational education.

(96) Installation, maintenance and repair of electrical and electromechanical equipment

Akimova N. Kotelenets N. Sentyurihin N.

Academy 1st 978-5-7695-8750-4

Moscow 2012 2.2-2.5, 3.2-3.3, 9.3-9.4, 16.1,17.2, 17.5, 19.1,23.2,24.1,

4 Deals with issues associated with the correct storage, installation and maintenance of electrical machinery and apparatus, transformers and electricity distribution networks. For students of secondary vocational schools.

(97) Reference book for repair of electrical equipment

Partala O.

Science and technics

1st 978-5-94387-804-6

St. Petersburg

2010 3.3, 9.1, 9.3,16.1,17.2,19.1,23.2

4 Repair of electric machines, transformers, stand-alone power generators, pumps and switching equipment, air conditioners, welding power supplies, etc. are considered.

(98) Electrical equipment of power stations

Rozhkova L.

Academy 11th 978-5-4468-1308-7

Moscow 2004 2.1, 2.2, 2.4, 9.4,

4 Information on electric power systems, features of processes at different types

113


ISBN code


Year of publication


Quantity Comments

and substations: The textbook for students of institutions of secondary vocational education.

17.4 of power plants.

(99) Reference book of electrician

Moskalenko V.

Academy 7th 978-5-7695-9170-9

Moscow 2012 2.1-2.5,3.1-3.3

4 Contains information about the purpose and technical characteristics of the main types of electrical equipment: cables and electrical insulation products, electrical devices of low and high voltage, The textbook is used for educational institutions implementing programs of primary vocational education

(100) Electric power meters

Tikhomirov М.

In-Folio 1st 978-5-903826-46-9

Volgograd

2011 17.3, 17.4, 19.1,23.1,

4 Outlines the main issues of the discipline Electrical power meters: Basics of electricity metering

114


ISBN code


Year of publication


Quantity Comments

24.1 according to regulatory documents, the principle of operation, design, circuit switching electric meters.Textbook for students of electrotechnical specialties of secondary special educational institutions

(101) Electric devices Ed.O. Devochkin, V.Lohnin, R. Merkulov

Academy 1st 978-5-4468-0197-8

Moscow 2013 2.4,19.1

4 The classification of electrical apparatus, the issues of theory and design, the scope of devices and prospects for their further development are given. The main types of electronic devices and sensors used therein are described. Textbook is for students of institutions of secondary vocational education.

(102) Electric systems and networks

Lykin А.

Logos 2nd 5-98704-055-8

Moscow 2006 2.2-2.4, 3.3, 9.3, 9.5

4 Discloses the production, transmission, distribution and consumption of electrical energy. The

115


ISBN code


Year of publication


Quantity Comments

concept of the electric power system (EPS) and its components is given.

(103) Electrical equipment of electrical power plants and substations

Karneeva L., Rozhkova L.

Inter-regional energy Correspondence College of the state educational institutions of secondary vocational education Ivanovo Power Engineering College

1st 5-93901-002-4

Ivanovo 2006 2.1, 2.2, 2.4, 9.4, 17.4

4 The book sets out the methods and examples of calculations of short-circuit in electrical systems with voltages above 1000 V.Tasks for self-exercising are given.

(104) Mechanic electrician. Reference-book

Bredikhin A.

Radiosoft 1st 978-5-93037-200-7

Moscow 2009 2.2-2.5, 3.2-3.3, 8.1, 9.4,

4 The book provides basic background information on mechanic, electrical installation technology and measuring tools, techniques for mechanic and electrical measurement operations.

116


ISBN code


Year of publication


Quantity Comments

(105) Modes of electrical equipment of electric power stations

VetrovN. Bykov L., Klyuchenovich V.

Novosibirsk State Technical University

1st 978-5-7782-1456-9

Novosibirsk

2010 2.1, 2.2, 2.4, 9.4, 17.4

4 The physical laws that occur in generators, transformers and motors; auxiliary power system in different modes.

(106) Human safety in electromagnetic fields

Apollonsky S., Kolyada T. Sindalovskii B.

Politechnika 1st 5-7325-0854-6

St. Petersburg

2006 2.1, 2.2, 2.4, 3.1 -3.3, 8.1 - 8.2,9.1-9.4,17.2, 17.4-17.5,19.1-19.2,23.2-23.3, 24.1

4 Considers medical and biological foundations of human life safety in electromagnetic fields

(107) Collection of regulations on labour protection for workers of the electricity

Mikhailov Y.

Alfa-press 1st 978-5-94280-502-9;

Moscow 2011 2.1, 2.2, 2.4, 3.1 -3.3, 8.1 - 8.2,9.1-9.4,17.2,

4 One of the first collections.Contains examples of regulations on labour protection and also sets out clear requirements for the organization of its

117


ISBN code


Year of publication


Quantity Comments

17.4-17.5,19.1-19.2,23.2-23.3, 24.1

development.

(108) Physical, parametric, and electrical issues of electrical safety

Patrickeyev L.

Sevastopol National University of Nuclear Energy and Industry

1st - Sevastopol

2002 2.1, 2.2, 2.4, 3.1 -3.3, 8.1 - 8.2,9.1-9.4,17.2, 17.4-17.5,19.1-19.2,23.2-23.3, 24.1

4 The main factors that determine the risk of a person damage by electric current. The analysis of the conditions for electric installations of AC and DC voltages is given.

(109) Occupational safety and electrical safety

Sibikin Y.

Radiosoft 1st 978-5-93037-282-3

Moscow 2014 2.1, 2.2, 2.4, 3.1 -3.3, 8.1 - 8.2,9.1-9.4,17.2,

4 Necessary electrical engineering personnel information on occupational safety and electrical safety given.It sets out the general

118


ISBN code


Year of publication


Quantity Comments

17.4-17.5,19.1-19.2,23.2-23.3, 24.1

provisions of the Rules of interbranch POT RM-016-2001 OSH (Safety) during installation, maintenance and repair of electrical equipment and Regulations for Electrical Installation (PUE).

(110) Occupational safety and electrical safety

Chekulaev V. Gorozhankina E.

The training center for education on railway transport

1st 978-5-89035-599-7

Moscow 2012 2.1, 2.2, 2.4, 3.1 -3.3, 8.1 - 8.2,9.1-9.4,17.2, 17.4-17.5,19.1-19.2,23.2-23.3, 24.1

4 This publication presents the main provisions, requirements and standards of occupational safety and electrical safety in the household electrification and power supply, as well as preventive measures and methods to prevent electrical injuries.The textbook is intended for students of technical schools, colleges, technical schools

(111) Electrical safety for electrical

Sibikin Y.

Academy 1st 5-7695-1391-8

Moscow 2004 2.1, 2.2, 2.4,

4 The causes of high danger when working on electrical

119


ISBN code


Year of publication


Quantity Comments

installations at industrial plants

3.1 -3.3, 8.1 - 8.2,9.1-9.4,17.2, 17.4-17.5,19.1-19.2,23.2-23.3, 24.1

installations; electrical safety, the standards OSSS and safety regulations.For students of primary vocational education.

(112) Occupational health and safety.

Belyakov G..

URAIT 1st 978-5-9916-6037-2

Moscow 2015 2.1, 2.2, 2.4, 3.1 -3.3, 8.1 - 8.2,9.1-9.4,17.2, 17.4-17.5,19.1-19.2,23.2-23.3, 24.1

4 The book contains organizational and legal issues, industrial hygiene, safety, fire safety, safety in emergencies, pre-medical aid to the victims in case of accidents. For students of secondary vocational schools.

(113) Health and Safety

Solomin V.

URAIT 1st 978-5-9916-

Moscow 2015 2.1, 2.2, 2.4,

4 The publication describes the causes and types of

120


ISBN code


Year of publication


Quantity Comments

5479-1, 3.1 -3.3, 8.1 - 8.2,9.1-9.4,17.2, 17.4-17.5,19.1-19.2,23.2-23.3, 24.1

man-made, natural and social emergencies. For each topic, questions are provided for the preparation and repetition, case studies and literature sources are proposed for a more detailed and in-depth study of issues of life safety. Tutorial and book for students of secondary vocational schools.

(114) Protective earth and protective neutral of electrical installations: reference book

Mankov V, Zagranichnyi S.

Politechnika 1st 5-7325-0791-4

Moscow 2005 2.1, 2.2, 2.4, 3.1 -3.3, 8.1 - 8.2,9.1-9.4,17.2, 17.4-17.5,19.1-19.2,23.2-23.3, 24.1

4 The book contains background information on the repair of basic electrical equipment - electrical machines, welding transformers, solenoids, oil power transformers, ballasts and power cables, as well as materials, products, machinery and tools used in the repair. The reference book is intended for students of

121


ISBN code


Year of publication


Quantity Comments

educational institutions of vocational training, preparing workers for electrical professions.

(115) Protective measures in electrical safety of electrical installations

Monakhov A.

Energoservice 1st 978-5-91245-031-0

Moscow 2008 2.1, 2.2, 2.4, 3.1 -3.3, 8.1 - 8.2,9.1-9.4,17.2, 17.4-17.5,19.1-19.2,23.2-23.3, 24.1

4 The analysis of the conditions of electric current damage in networks with different modes of neutral characteristics of insulation and earthing systems is given.

122

List of educational literature from publishers of the Republic of Kazakhstan in Kazakh and Russian


ISBN code


Year of publication


Quantity Comments

(116) Electrical equipment of electrical power stations: Textbook

Aikeeva A.

International Business Academy

1st 978-601-7431-12-9

Karaganda

2013 2.1, 2.2, 2.4, 9.4, 17.4

4 The tutorial discusses types of electrical equipment, including switchgear for low and high voltage.

(117) Installation of production facilities and repair of electrical equipment

Kosybayev K.

Folliant 1st 978-601-292-186-1

Astana 2010 2.2-2.4, 3.2-3.3,8.1, 9.4, 16.1,17.5,

4 Production of electrical equipment, Setting out the procedure for the efficient use and maintenance of electrical equipment. Repairing electrical equipment, Post-repair testing methods For students in vocational education institutions training to be an operating technician or electrician

123


ISBN code


Year of publication


Quantity Comments

(118) Electrical Engineering

Mukhiti I.

Folliant 2nd 978-601-292-365-0

Astana 2011 2.1 - 2.5,3.1 - 3.2, 9.1,

4 Deals with electric and magnetic garlands, transformers, electrical machines, ground elements of the electronic devices, electrical measurement and measurement instruments narrow, control and protection equipment, electrical drive and provides basic information about the power supply.

(119) Parts of electric power stations

Kurast L., Bainazarova

Kazakh National Technical University

1st - Almaty 2012 2.4,3.3

4 Distinguishing between parts of power plantsElectricity distribution associated with power plantsProduction and distribution of electrical energy

(120) Electrical protection relay

Kurast L., Arynov


1st - Almaty 2012 2.4 4 Textbook intended to acquire good knowledge of electrical relay protection equipment for the specialty 050718 - "Electrical power"

124


ISBN code


Year of publication


Quantity Comments

of the curriculum taught to students in educational methodical complex (EMC), as part of its theoretical rules.

(121) Transients in power supply systems

Kurast L., Abitayeva


1st - Almaty 2012 2.1, 2.2, 2.4, 3.1-3.3, 8.1-8.2, 9.1-9.4, 16.2, 17.2, 17.4, 17.5, 19.1, 23.2-23.3, 24.1

4 Transition process of electrical energyConsidering certain occasions such as emergency situations, short-circuiting, etc.

(122) Labour Safety: Textbook

Khakimzhanov T..

Evero 1st 978-601-240-004-5.

Almaty 2008 2.1, 2.2, 2.4, 3.1-3.3, 8.1-8.2, 9.1-9.4, 16.2, 17.2,

4 This tutorial contains acts of the Republic of Kazakhstan in the field of health and safety protection. It displays economic and workplace health and safety standards.

125


ISBN code


Year of publication


Quantity Comments

17.4, 17.5, 19.1, 23.2-23.3, 24.1

(123) Fundamentals of life safety

Balabas L.

Folliant 1st 978-996-535-610-0

Astana 2008 2.1, 2.2, 2.4, 3.1-3.3, 8.1-8.2, 9.1-9.4, 16.2, 17.2, 17.4, 17.5, 19.1, 23.2-23.3, 24.1

4 The training manual sets out general and specific issues of health and safety on the basis of the legal framework regulating social relations in the territory of the Republic of Kazakhstan in the field of civil defence and emergencies. Textbook meets the requirements of the State obligatory standard of secondary technical and vocational education of the Republic of Kazakhstan.

(124) Labour safety in power systems

Amanzholov N.

Folliant 2nd 978-601-292-856-3

Astana 2014 2.1, 2.2, 2.4, 3.1-3.3, 8.1-8.2,

2 The textbook presents fundamentals and regulations of security and safety in the legal

126


ISBN code


Year of publication


Quantity Comments

9.1-9.4, 16.2, 17.2, 17.4, 17.5, 19.1, 23.2-23.3, 24.1

framework of the Republic of Kazakhstan: the control system of labour protection in enterprises, industrial hygiene, electrical safety, fire safety, and methods of analysis of occupational injuries and professional diseases. Considerable attention is paid to general safety aspects when working in electrical installations. The manual is intended for college students of electrotechnical specialties.

(125) Occupational health and safety

Amanzholov Zh.

Folliant 2nd 978-601-292-883-9

Astana 2014 2.1, 2.2, 2.4, 3.1-3.3, 8.1-8.2, 9.1-9.4, 16.2, 17.2, 17.4, 17.5,

4 The textbook presents fundamentals of legal and regulatory safety and labour protection, the occupational safety management system in enterprises, industrial hygiene, electrical safety, fire safety and methods of analysis of occupational

127


ISBN code


Year of publication


Quantity Comments

19.1, 23.2-23.3, 24.1

accidents and occupational diseases. The manual is intended for students in technical vocational institutions in construction and engineering specialties.

(126) Labour safety Nurzhasarova M.

Folliant 1st 9965-35-1778-3

Astana 2007 2.1, 2.2, 2.4, 3.1-3.3, 8.1-8.2, 9.1-9.4, 16.2, 17.2, 17.4, 17.5, 19.1, 23.2-23.3, 24.1

4 This manual is intended for students in secondary and basic vocational education. It focuses on occupational safety. The manual deals with the preservation of life and health of workers in the course of their work


Yashkov V.

Folliant 1st 978-601-292-220-2

Astana 2010 3.1, 9.2, 9.4, 17.2, 17.4, 19.1,

4 Presents data on electric instruments and measurements, adjustment of electrical machines, transformers and other

128


ISBN code


Year of publication


Quantity Comments

23.2 electrical components and devices. It also covers safety rules set out in testing and commissioning works. The directory is intended for students of primary and secondary vocational education, students discipline Maintenance, Repair and adjustment of electrical equipment and electrical networks, as well as professionals involved in testing and commissioning of electrical equipment.

(128) Labour safety system and environment protection

Drizhd N.

Folliant 1st 978-996-535-582-0

Astana 2007 2.1, 2.2, 2.4, 3.1-3.3, 8.1-8.2, 9.1-9.4, 16.2, 17.2, 17.4, 17.5, 19.1,

4 The tutorial discusses basic issues of labour protection, environmental protection and environmental management, taking into account ergonomic, economic, environmental and social factors. It is intended for students of primary and secondary

129


ISBN code


Year of publication


Quantity Comments

23.2-23.3, 24.1

vocational training in educational institutions.

(129) Over-voltage and insulation systems of power supply

Alibayev E.

Kostanay State University

1st - Kostanai 2013 2.4,3.1, 3.2, 17.4,

4 Industrial, municipal and household objects In this book students get acquainted with the ways of power supply systems, insulation etc.

(130) Electric drive control systems: Textbook

Breido I., Telbayeva E. Shakhaev

Karaganda State Technical University

1st - Karaganda

2009 3.1, 9.1, 9.4, 17.2, 17.4, 19.1, 23.2

4 Deals with electric control systems, requirements given by law as well as necessary calculations regarding the construction of electric drive control systems

130

kasipkor.kzkasipkor.kz/wp-content/uploads/2016/09/43-electrical-equipment-o… · web...

Documents