welcome to the bollard pull calculator for barges - rev 02 · pdf filewelcome to the bollard...
TRANSCRIPT
Welcome to the Bollard Pull Calculator for Barges - Rev 02
What does this Excel Sheet do?
This Excel sheet helps you calculate the Required Bollard pull of a Tug used for towing a Barge
How is the Excel Sheet Organised?
The Excel Sheet provides four different methods for calculations.
The First Method is based on DNV rules for Marine Operations. This is contained in the sheet named "Bollard Pull - DNV"
The Second Method is using industry standard OPL Guidelines for Barge Transportation Vol 5. This is contained in the sheet named "Bollard Pull - OPL Guideline"
The Third Method is based on Bureau Veritas rules and formulas for Bollard Pull Calculations. This is contained in the sheet named "Bollard Pull - BV"
The Fourth method is using a simple Empirical formula. This is contained in the sheet named "Empirical Formula". It provides Bollard Pull for different weather conditions: Calm, Rough and Extreme
How to use this Excel SheetIn all the three methods, the user is asked for some inputs to be provided. For example, the Wetted Surface area of Barge, Wind Speed etc. The Input cells are highlighted in blue.The user has to provide all the inputs highlighted in blue.For some inputs, Tables and charts are required to be referred. These Tables and charts are provided alongwith for the user to enter these inputs.Once all inputs are provided, the components of required bollard pull are calculated and added up to give the final Bollard Pull required.
Change log Rev 021. DNV Formula - Added Wave Resistance now based on DNV-RP-H1032. References updated for DNV method3. OPL method - Wave effect resistance is now being automatically calculated, and user need not input it4. OPL method - some typo errors rectified
Spherical 0.4
Parameter Notation Value Units Cylindrical 0.5Air Density ρa 1.225 kg/m
3Large flat surface (hull, deckhouse, smooth under deck areas) 1
Sea Water Density ρw 1025 kg/m3
Drilling derrick 1.25
Acc. Due to Gravity g 9.81 m/s2
Wires 1.2
3.88 MT Exposed beams and girders under deck 1.3
Small parts 1.4
Parameter Notation Value Units Isolated shapes (cranes, beam, etc) 1.5
Length L 116.00 m 0.00 MT Clustered deck houses or similar structures 1.1
Breadth B 36.60 m
Depth D 7.00 m 3.88 MT Reference: ABS, 2016, Rules for Building and Classing Mobile Offshore Drilling Units, Part 3 Chapter 1,
Draft (Mid) T 3.00 m Section 3, ‘Environmental Loadings’, p.11.
Type of Bow (1 - Square face, 2 -
Raked, 3 - Spoon, 4 - Ship Shape)3
Freeboard f 4.00 m
Hull Windage Area AWH = B X f 146.40 m2
1.43 MT
Hull Underwater Area ACH = B X T 109.80 m2
1.00
Current Drag Coefficient (Hull) CD 1.00 Over Not exceeding Ch 0.97
0 15.3 1 0.88
315.3 30.5 1.1 0.67
0.55 30.5 46 1.2 0.55
35.46 MT 46 61 1.3 0.45
Parameter Notation Value Units *Reference: DNV RP-H-103, Sec 7.2.6.4 61 76 1.37
Breadth Overall Bc 0.00 m 76 91.5 1.43
Height Overall Hc 0.00 m 91.5 106.5 1.48 Reference, DNV-RP-H103, 2011, Table 7-1
Height Coefficient Ch 1.10 See Table 1 106.5 122 1.52
Shape Coefficient Cs 1.00 See Table 2 3.88 MT 122 137 1.56
Cargo Windage Area AWC = BC X HC 0.00 m2
1.43 MT 137 152.5 1.6
35.46 MT 152.5 167.5 1.63
40.78 MT 167.5 183 1.67
183 198 1.7
Parameter Notation Value Units 198 213.5 1.72
Wave Height HS 5.0 m 0.75 213.5 228.5 1.75
Current Speed VC 0.5 m/s **Reference: DNV Rules for Marine Operations Pt2 Ch2, Towing, 3.3.2.6 228.5 244 1.77
Wind Speed VW 20.6 m/s 244 259 1.79
259+ 1.8
54.37 MT
Parameter Notation Value Units Use Centre of Area for Above Heights
Actual Bollard Pull of Tug BPT 60.0 MT Reference: ABS, 2016, Rules for Building and Classing Mobile Offshore Drilling Units, Part 3 Chapter 1,
Tug Efficiency η 0.75 Section 3, ‘Environmental Loadings’, p.11.
Change Log (Rev 02)
1. DNV Calculation now based on DNV-RP-H-103, the latest document from DNV which replaces the earlier Rules for Marine Operations (2000)
Table 2: Height Coefficient
Current Resistance FC
Fc
CARGO
FW = FWH + FWC
Ch: Height Coefficient
Height above sea level (metres)
TUG EFFICIENCY
SEA STATE
TOTAL RESISTANCE, FT = FW + FC + FD
INPUTS REQUIRED BOLLARD PULL CALCULATION FOR BARGES TOW PULL CALCULATION - DNV METHOD
This method is based on DNV Recommended Practice RP-H103 7.2.6 (Applicable for zero towing speed).
Shape and Height coefficients are taken from ABS MODU Rules 2016
Table 1: Shape Coefficient
Summary: This method calculates the Required Bollard Pull to hold the tow in a given Sea State. The Standard Sea State
used is Hs = 5m, Current = 1 kn and Wind =40 Kn. Directions: The applicability of the method is shown in the box titled
"Applicability Check" on the left. All input cells are in blue. Tug efficiency can be varied. Coefficients Cs and Ch can be
obtained from the Tables on the right.
Wind Resistance, FW = FWH + FWC
FWH = Wind Resistance for Hull
FWH = 1/2 x ρa x VW2 x AWH
FWH
REQUIRED BOLLARD PULL 54.37 MT
Cs : Shape Coefficient
GENERAL
BARGE
FWC = 1/2 x ρa x VW2 x AWC x Ch x Cs
FWC = Wind Resistance for Cargo
FC = 1/2 x ρs x CD x VC2 x ACH
Tug Efficiency, η**
Current Resistance, FC
Wind Resistance, FW
Wave Drift Resistance, FD
Total Resistance, FT
FD
Reflection coefficient, R (See Table 3)
FW = Total Wind Resistance
FWC
BPTUG
Since Required Bollard Pull < Actual Bollard Pull => OK
REQUIRED BOLLARD PULL (BP = FT / η )
Wave Drift Resistance (FWD)*
FWD = 1/8 x ρs x R2 x B x HS
2
Type of Bow (1 - Square face, 2 - Raked,
3 - Spoon, 4 - Ship Shape)
Barge with Spoon bow
Ship bow
Table 3: Reflection Coefficients
R: Reflection Coefficients
Square Face
Condeep base
Vertical Cylinder
Barge with Raked bow
Cargo Breadth = BC
Cargo Height Hc
Cargo Windage Area AWC= BC X HC
Hull Windage Area AWH= B X f
Draft ,T
Depth, DFreeboard, f = D -T
Hull Underwater Area, ACH = B X T (approx.)
Breadth, B
Sectional View of Barge with Cargo
BARGE NAME Directions:1. Fill the input cells which are in blue.
TOWING SPEED -----> knots 5.0 2. The outputs will show in the bottom as the final Bollard Pull required.Actual Bollard Pull of Tug -----> tonnes 60.0Towing Efficiency in % (Default value 75%) 75.0
3. Use Table 1 for calculating the Height coefficient for Wind
4. Use Table 2 for finding the Shape Coefficient for windUnit Value 5. Use Table 3 to calculate the Wave Effect Resistance which depends on the wave height.
Fouling coefficient(0.4 clean hull, 0.85 fouled hull, usually
0.625)f1 - 0.63
In case the value of Wave Height falls in between two values given in the table, interpolation is to be used
Wetted Surface of the Hull S ft2 55553.34
Still water tow speed in knots v knots 5.0
Frictional Resistance RF tonnes 10.94
Unit Factor
feet 1
Unit Value feet 1.1Hull Shape Coefficient (0.20 for rake ended barges and bluff
bowed vessels and 0.50 for square bowed vessels) f2 - 0.2feet 1.2
Transverse Area(Underwater) AT ft21181 feet 1.3
Still water tow speed in knots v knots 5.0 feet 1.4
Wave Forming Resistance RWF tonnes 9.17 feet 1.5
feet 1.6
Table 1: Cargo Height Coefficient for Wind Calculations
Unit ValueHeight Coefficient for Cargo Exposed to Wind (See Table 1) Ch - 1Shape Coefficient for Cargo Exposed to Wind (See Table 2) Cs - 1
Cargo Transverse Area (Exposed to wind) AC ft20.0 Cs
Vessel Transverse Area (Exposed to wind) AH ft21575.0 0.5
Total Transverse Area AT ft21575.0 Flat Perpendicular Surface 1
Wind Velocity vW knots 40.0 1.5
Still water tow speed in knots v knots 5.0 1.3
Wind force RW tonnes 4.92 1.25
0.4
Table 2: Carge Shape Coefficient for Wind Calculations
Unit Value
Wetted Surface of the Hull S ft2 55553
Current Speed vC knots 1.0
Current Effect Resistance RC tonnes 0.40
5 feet 2000 lbs
10 feet 12000 lbs
15 feet 22000 lbs
Unit Value 20 feet 29000 lbs
Wave Height ft 16 25 feet 30000 lbs
Force at 16 feet wave - See Table 3 FWR lbs 23,400 30 feet 33000 lbs
Wave Effect Resistance RWH tonnes 10.62
Table 3: Wave Effect Resistance Table
Unit Value
Frictional Resistance RF tonnes 10.9
Wave Forming Resistance RWF tonnes 9.2
Hawser Resistance RH tonnes 2.01
Frictional Resistance RF tonnes 10.94
Wave Forming Resistance RWF tonnes 9.17
Wind Resistance RWH tonnes 4.92
Current Effect Resistance RC tonnes 0.40
Wave Effect Resistance RWH tonnes 10.62
Hawser Resistance RH tonnes 2.01
Total Resistance RT tonnes 38.1
Tug Efficiency in percentage(Default value 75%) η 75.0
Required Bollard Pull = (RT/η)*100 BP TONNES 50.74
Actual Tug Bollard Pull TONNES 60.00Satisfied/Not Satisfied? Yes
Wave Height Effect – For wave Force on Hull:
Significant Wave Height Added Resistance
Height
0-50
50-100
100-150
150-200
200-250
250-300
300-350
Derrick (latticed structures)
Sphere
Shape
Factor Ch (Height coefficient for wind calculations)
Factor Cs (Shape coefficient for wind calculations)
Cylinder
Isolated Structure – Beam-channel angle braces
Exposed Beams
RT = RF + RWF + RW + RC + RWH + RH
RWF = 3.42 (f2)(AT)(v)2 , lbs.
RC = 0.016 (S)(vC)2 , lbs.
Description
Description
Calculation of Wave Effect
Calculation of Hawser Resistance:
CALCULATION OF REQUIRED STATIC BOLLARD PULL FOR BARGE: OPL Guidelines
Description
Description
Description
Description
BARGE 1
Reference: OPL Oilfield Seamanship Series - Volume 5: Barge Moving
Calculation of Frictional Resistance:
Calculation of Wave Forming Resistance:
Calculation for Wind Resistance:
Calculation of Current Effect
RW = 0.0034 (AT)(vW+v)2 , lbs.
RF = f1 (S)(v/6)2 , lbs.
OUTPUTS
Calculation of Total Resistance:
From Table 3
RH = 0.10 (RF + RWF)
Directions:
BARGE NAME: BARGE 1 1. Fill the input cells which are in blue.
2. The output will show in the bottom as the final Bollard Pull required.INPUTS 3. Use Appendix 1 for calculating the coefficients Cx and Ch
Symbol Value Unit Description 4. Use Graph 1 below for finding the value of Rv/DL = 116.00 m Waterline LengthB = 36.60 m Breadth
T = 3.00 m Draft APPENDIX 1: Tables for Cx and ChV = 5 Kn Vessel Speed (Towing Speed)Vc = 1 Kn Assumed Current Speed D = 11463 t DisplacementS = 146.4 m^2 Windage Aread = 65 mm Tow Line Diameterl = 700 m Tow Line Immersed LengthZ = 1 m Sag of Tow LineP = 900 m Tug to Towed Vessel DistanceN = 150 days Number of Days Elapsed Since last Dry Docking
Vfr = 18 Kn Maximum Towing Vessel Speed in Free Runrsw = 1.025 t/m^3 Sea Water Specific Gravity (default value 1.025)rair = 1.22 kg/m^3 Air Specific Gravity (default value 1.22)n = 1.2E-06 m^2/s Viscosity (default value 1.2 10^-6)
Vw = 40 Kn Wind Speed (default value 40)BPt = 60 Tonnes Actual Bollard Pull of Tug
Symbol Value Unit Description
Rf = ½ Cf (rsw)(Sw)(v)2
R = 298375200 Reynolds Number, R = vL / ν
Cf = 0.001789 Friction Coefficient, Cf = 0.075 / [log10 R)-2]2
DCf = 0.002147 Addition to Friction Coefficient due to Hull Fouling, DCf = 0.008 (N)(Cf)Cft = 0.004336 Total Friction Coefficient, Cft = Cf + DCf +0.0004Sw = 4485.44 m^2 Wetted Surface Area
Rf = 94961 N Frictional Resistance
L/B = 3.17B/T = 12.20
V/(L)^0.5 = 0.29Rv / D = 12.00 (To be taken from the Graph 1 on the right)
Rv = 137556 N Wave Resistance
Rh = 232517 N Total Hydrodynamic Resistance
Ra = ½ Cx * Ch * (rair)(S)(Vw)2
Cx = 1 Drag Coefficient(To be taken from the Appendix1 on the right)Ch = 1 Height Coefficient(To be taken from the Appendix1 on the right)Ra = 37815 N Aerodynamic Resistance
Rr = 4.6 x10-3 (d)(v)2( l + (71.6 Z/P)) , in Newton
Rr = 1994 N Tow Line Resistance
Rtot = 272325 N
(V+Vc)/Vfr = 0.33 Graph1: Graph for Values of Rv/DCef = 0.67 Percentage of Static Bollard Pull = (1 - (V+Vc)/Vfr)
Rt = 41.6 T
BPt = 60.0 T
Satisfied/Not Satisfied Yes
Actual Bollard Pull for Tug, BPt
Tow Line Resistance Rr
Total Resistance of Towed Vessel
Bollard Pull Coefficients
Total Required Static Bollard Pull for Tug, Rt
Aerodynamic Resistance Ra
CALCULATION OF REQUIRED STATIC BOLLARD PULL FOR BARGE: BV Rules and Formulas
RESULTS
Frictional Resistance Rf
Wave Resistance Rv
Total Hydrodynamic Resistance Rh
FORMULA USEDINPUTS: Please input the following Using Empirical Formula for towing guide by Port Authorities
Unit Value
BARGE 1 BP = { [ (∆⅔ · (v3/ (120 · 60)) ] + (0.06B · D1) } · K (tonnes)
m 116.00m 36.60 Where:
tonnes 11463.00 ∆ = full displacement of towed vessel, in tonnesm 7.00 v = tow speed, in knots
m 3.00 B = breadth of the vessel, in meters
m 0.00 D1 = depth of exposed transverse section of the vessel including
75.00 deck cargo above the water line, in meters
Yes/No Notonnes 60.00
BP = Required bollard pull, in tonnes
Note: For tow by the stern, then the Bollard Pull requirement is to be increased by 20% K = the factor depending on the likely condition to be met. This factor is
intended to reflect desired weather margins.
OUTPUTS: CALCULATED BOLLARD PULL WITH VARIOUS WEATHER CONDITIONS & TOWING SPEEDS In General: • for exposed tows, K = 1.0 - 3.0
• for sheltered tows, K = 0.75 - 2.0
Good Rough Extreme • for protected tows, K = 0.50 - 1.5
116.00 116.00 116.005.00 4.00 3.00 <---- Please input the different speeds considered for the three weather conditions
36.60 36.60 36.6011463.00 11463.00 11463.00
7.00 7.00 7.003.00 3.00 3.000.00 0.00 0.004.00 4.00 4.001.00 2.00 3.00
17.89 26.89 32.2575.00 75.00 75.00
23.85 35.86 43.00
No No No23.85 35.86 43.0060.00 60.00 60.00
SATISFIED SATISFIED SATISFIED
Actual TUG Bollard Pull
Tow by Stern?Final Bollard Pull, BP (in tonnes)
CALCULATION OF REQUIRED STATIC BOLLARD PULL FOR BARGE: Empirical Formula
Required Bollard Pull as per formula, RtTug Efficiency in percentage(Default 75%), ηBollard Pull considering Tug Efficiency =
(RT/η)*100
Description
Length, LTowing Speed, VBreadth, BDisplacement, ∆
Actual TUG Bollard Pull
Description
Length, LBARGE NAME
Breadth, BDisplacement, ∆Depth, DDraft, dCargo Height, HTug Efficiency in percentage(default 75%)Is it Tow by Stern?
Depth, DDraft, dCargo Height, HExposed Height, D1Weather Factor, K
Terms and Conditions
License Terms – Simple general usage terms are as follows:1. When a template or software is purchased only one person may use it. If more people will be using the same template or software, purchase multiple copies of the template or software equal to the amount of people using it. 2. A non-exclusive conditional license to use templates or software is what is being purchased on this site. Copies of these templates and software are not to be sold, given away or distributed. Templates and software always remain the property of www.thenavalarch.com.3. These products are non-transferable. You may not purport to give anyone else rights in the templates or software. You many not allow anyone else to have your licensed copies of templates or software.4. Template users assume all liability for their usage. It is up to the template or software user to verify that all the data they incorporate, all spreadsheet or software changes they incorporate and all initial spreadsheet and software algorithms are correct.
Liability Statement – www.thenavalarch.com has meticulously strove to assure the accuracy and quality of these templates and software. They are designed to significantly reduce the template user’s spreadsheet setup time or software users working time. However, there are numerous scenarios, which could affect the results obtained from these templates and software. For instance: the input data could be corrupt, the spreadsheet or software could be improperly modified, or some other unforeseeable conditions may occur. Therefore, the template or software user is required to independently verify that the all aspects of the spreadsheets or software are working properly. www.thenavalarch.com assumes no liability for template or software usage including the results obtained.Notify us, at [email protected], if you find a bug or any other inaccuracies or inconsistency in the templates, software, documentation or in this website. Please contact us us so that we may be able to correct the problem. Thank you.Legal Disclaimer Statement – All templates, software, notes, documentation, pages and other information are provided "as is," without warranty of any kind, either expressed or implied, including without limitation, fitness for a particular purpose or performance. By using the templates, software or acting on any information included within this web site, YOU AGREE TO ASSUME THE ENTIRE RISK, for any result, performance, or lack of performance, including damage to data and/or damage to property.Neither the webmaster, site owner, agents, nor any third parties shall be liable to you, for -ANY- use of these templates, software or content (including ANY INABILITY to use), for its performance, for any incidental or consequential damages, and/or ANY claim by ANY other party.