Firmware v2.00Edition 1, 9/2010

OX350WiMAX MIMO Outdoor Simple CPE

DEFAULT LOGIN DETAILS

IP Address: http://192.168.1.1

Username: admin

Password: 1234

2

IDU and ODU

POESIGNALSTRENGTH POWER

ETHERNET POWERPOEPORTPORT

ONLED

CONNECTLED FAULT

LED

ODURESET

BUTTON

IDU

LEDS

ENGLISH

3

Introduction

Welcome to the OX350! This is a WiMAX subscriber station system comprised of an outdoor unit (ODU) and an indoor unit (IDU).

The ODU such features as a high gain antenna and advanced IP networking while the IDU provides power to it. It also provides connectivity to the devices in your home or office at the same time.

The ODU connects to the WiMAX network while the IDU is the management point between the WiMAX network (via the ODU) and your computer/local area network.

Firmware Caution: When your ISP upgrades your device’s firmware, all of the LEDs will flash simultaneously. Do not turn off or unplug the device until they stop blinking.

How It Works

4

Before You Begin

Ensure that you have everything required to properly set up your device.

What You Need• The WiMAX ODU

• The WiMAX IDU

• AC Power Cord

• One 1.8 meter long CAT5 Ethernet cable for connecting the IDU and your computer

• Cable Gland Body, Claw and Nut

• Mounting Kit

• Grounding Kit

• This Quick Start Guide

• The Support Disc containing the User’s Guide and device drivers

• Another CAT5 8-wire Ethernet cable (not included) for connecting the IDU and ODU

Minimum System Requirements• 64 MB RAM

• 20 MB of available hard disk space

• One available 10/100Mbps Ethernet port

• Internet Explorer 7, Firefox 2 and higher, or a compatible browser

ENGLISH

5

Installing the Outdoor Unit

Before you begin, ensure that you are familiar with all safety and accident prevention procedures necessary for working at heights and with electricity.

Do NOT install the ODU during a lightning storm.

Choose a Location

The ODU can be mounted on a pole or antenna mast or on a wall using the supplied bracket mount.

• Choose a mounting point that is sturdy enough to hold the ODU, even during high winds.

• When choosing a location to install the ODU, remember that the ODU’s front panel should point towards your service provider’s nearest base station. If you are not sure where this is, consult your service provider.

• You do not need to be able to see the base station from the ODU’s position; there may be objects such as trees and buildings in the way without signal loss. However, if you experience difficulties with signal reception, a Line of Sight (LoS) connection may produce better results.

• It is suggested that you transport the ODU to its intended installation location in its original protective packaging.

Connecting the CAT5 Ethernet Cable

Lay the CAT5 Ethernet cable (not included) from your intended IDU location to your intended ODU location.

6

• If you use cable extenders to cover a greater distance, signal attenuation may result.

• If you intend to use cable ties or other methods to secure the cable, do not tighten them yet. Leave the cable loose until you have finished installing the IDU and ODU.

Ensure you have the included Cable Gland Body, Claw and Nut parts, as pictured below. These are required.

To connect the CAT5 Ethernet cable:

1. Separate the body, claw and nut pieces into their individual components.

2. Feed one end of the CAT5 Ethernet cable through the nut.

Body NutClaw

ENGLISH

7

3. Open the claw then buckle it tightly to the cable.

4. Slip the body over the cable then connect the end of the cable to the ODU.

5. Gently twist the body into the ODU behind the attached cable connector.

8

6. Tightly secure the CAT5 Ethernet cable connector and the body and claw with the nut.

Mount the ODU

See the installation instructions that came with your bracket mount for information on mounting the ODU correctly.

To avoid the danger of rainwater entering the device, install the ODU vertically (with a 90 degree angle to the ground).

Package List

The poll mounting kit contains the following:

1. Six M6 Nuts

2. One Pole Bracket

3. One U Bolt

12

3

ENGLISH

9

Pole Mounting

You can install the WiMAX Modem vertically with a +15, 0, or -15 degree angle relative to the pole. The connectors should be pointed down. The following steps show you how to install it with a 0 degree angle.

4. For +15o and 0o angle installations, position the bracket with the +15o mark on the top.

• Use the two holes (marked as A) for +15o angle installation.

• Use the two holes (marked as B) for 0o angle installation.

For -15o installation, position the bracket so the -15o mark is on top.

+15o 0o -15o

A

B

10

5. Align two M6 nuts to the bottom two holes to attach the pole bracket to the U blot on a pole or mast. Use a wrench to tighten the nuts with the U blot.

6. Align the four edge holes on the mounting bracket with the screws on the rear of the WiMAX Modem. Then use a wrench to tighten the four nuts with the screws.

ENGLISH

11

Grounding

The grounding kit contains the following:

Do the following steps for grounding the WiMAX Modem:

1. Use the M3 screw to secure the ground cable and the ground hole on the WiMAX Modem’s rear panel as shown.

1. One M3 Screw

2. One Ground Cable12

12

2. Attach the other end of the ground cable to a wall or the ground.

ENGLISH

13

Setting Up Your Modem

This section shows you how to set up your WiMAX Modem.

You will need a valid WiMAX account to connect to the Internet. For more information, contact your service provider.

1. Connect the power cord to the IDU. The ON LED shines a steady green once connected.

1

2

3

14

2. Connect a CAT5 Ethernet cable (not included) to the IDU. The other end should already be connected to the ODU, as described in the previous section. The CONNECT LED shines a steady green once the IDU is connected to both a power source and the ODU.

3. Connect the included Ethernet cable from the computer to the power block.

Connecting to the Internet

This section shows you how to connect to the Internet with your device.

1. Open a web browser.

• If your service provider’s WiMAX login page appears instead of your default Home page then all you need to do is enter the login information that you were given and follow the on-screen instructions. The WiMAX Modem should then automatically update itself with the settings that you need to connect to the Internet.

• If your service provider’s WiMAX login page does not appear, then you may need to use the Connection Wizard (see page 14).

The Connection Wizard

This section shows you how to manually configure the WiMAX Modem.

1. Open a web browser and go to http://192.168.1.1.

ENGLISH

15

2. Enter the default Username (admin) and Password (1234), and then click Login.

The main Status screen displays.

3. Click the Setup Wizard Setup button.

16

4. When the Setup Wizard opens, review the steps you will take to configure your WiMAX Modem then click Next to continue.

The LAN and WiMAX settings required by the Setup Wizard should be provided by your Internet Service Provider.

5. LAN Settings: Configure the network settings that allow devices connected to your WiMAX Modem to get on the Internet or connect to other network services. Then Click Next.

ENGLISH

17

6. WiMAX Frequency Settings: Configure the radio frequency on which your WiMAX Modem sends and receives data. Then Click Next.

7. WiMAX Authentication Settings: Configure how your device logs into the service provider’s network. Then Click Next.

18

8. In the Setup Complete screen, click Save.

Troubleshooting

Use this section if you have problems with your WiMAX Modem.

I cannot access the WiMAX Modem from my LAN:

• Check the cable connection between the WiMAX Modem and your computer or switch and ensure that both ends are secure.

• Make sure your computer has gotten an IP address (default is 192.168.1.x) in the same network as the WiMAX Modem’s LAN. If not, you can manually configure your computer by clicking Start > Control Panel > Network Connections > Local Area Connection > Properties > Internet Protocol (TCP/IP).

• Ping the WiMAX Modem from a LAN computer: Click Start > (All) Programs > Accessories > Command Prompt. When the

ENGLISH

19

command prompt window opens, type "ping 192.168.1.1” without quotes and press [ENTER]. The WiMAX Modem should reply.

• Press and hold the Reset button for about 10 seconds to reset the device to its default factory settings, then try to connect to the IP 192.168.1.1 once more.

I cannot log into the Web Configurator:

• Check to see if anyone else is currently logged into the WiMAX Modem. If so, you may not be able to log in until they log out first.

• If you’ve forgotten the WiMAX Modem’s user name, password, or IP address press and hold the Reset button for about 10 seconds. The WiMAX Modem returns to the factory default settings listed on the first page of this book.

20