wireless n open source access point - d-link€¦ · the d-link wireless n open source access point...

Wireless N Open Source Access Point

2D-Link DAP-1360 User Manual

Table of Contents

Package Contents ......................................................................... 4System Requirements ................................................................. 5Introduction ................................................................................... 6Features ............................................................................................ 8Hardware Overview ..................................................................... 9

Connections ........................................................................... 9LEDs .........................................................................................10WPS LED/Button..................................................................11

Installation .......................................................................12Operation Modes ........................................................................12

Access Point Mode .............................................................13Wireless Client Mode .........................................................14Repeater Mode ....................................................................15Bridge Mode .........................................................................16Bridge with AP Mode ........................................................17WISP Client Router Mode .................................................18WISP Repeater Mode .........................................................19

Wireless Installation Considerations ....................................20

Configuration ...................................................................21Web-based Configuration Utility ..........................................21Wireless Setup Wizard ...............................................................22

Access Point Mode .............................................................23Repeater Mode ....................................................................26Wireless Client Mode .........................................................30

Manual Configuration ...............................................................34Wireless Settings .................................................................34

Access Point Mode ........................................................35Repeater Mode ...............................................................37Wireless Client Mode ....................................................38Bridge Mode ....................................................................39Bridge with AP Mode....................................................40WISP Client Router/WISP Repeater Modes ...........41

WAN Settings .......................................................................42Dynamic IP (DHCP) ........................................................42Static IP ..............................................................................43PPPoE .................................................................................44PPTP ....................................................................................45

LAN Settings .........................................................................46Static IP ..............................................................................47

Advanced ......................................................................................48Advanced Wireless .............................................................48

MAC Address Filter .....................................................................49Wi-Fi Protected Setup ...............................................................50User Limits .....................................................................................51Port Forwarding (WISP modes only) ...................................52Port Filter (WISP modes only) ................................................53DMZ (WISP modes only) ..........................................................54Parental Control (WISP modes only)....................................55Advanced Network (WISP modes only) .............................56Maintenance ................................................................................57

Admin .....................................................................................57System ....................................................................................58Language Pack .....................................................................59

Table of Contents


Table of Contents

Firmware ................................................................................59Watchdog ..............................................................................60Time .........................................................................................61System Check .......................................................................62Schedules ..............................................................................63

Status ..............................................................................................64Device Info ............................................................................64Logs .........................................................................................65Statistics .................................................................................66Wireless ..................................................................................67IPv6 ..........................................................................................68

Help .................................................................................................69

Wireless Security .............................................................70What is WPA? ................................................................................71Configure WPA/WPA2 Personal .............................................72Configure WPA/WPA2 Enterprise ..........................................73

Connect to a Wireless Network .......................................74Using Windows® XP ....................................................................74Configure WPA-PSK ....................................................................75Using Windows Vista® ...............................................................77Configure WPA-PSK ....................................................................79Using Windows® 7 .......................................................................80

Configure WPS .....................................................................83

Troubleshooting ..............................................................87

Wireless Basics .................................................................91What is Wireless? .........................................................................92Tips ...................................................................................................94Wireless Modes ............................................................................95

Networking Basics ...........................................................96Check your IP address ...............................................................96Statically Assign an IP address ...............................................97

Technical Specifications ..................................................98


Section 1 - Product Overview

Note: Using a power supply with a different voltage rating than the one included with the DAP-1360 will cause damage and void the warranty for this product.

Package Contents

DAP-1360 Wireless N Open Source Access Point

Ethernet Cable

Two Detachable Antennas

CD-ROM with Manual

Power Adapter



System Requirements

Network Requirements

• AnEthernet-basedNetwork• IEEE802.11n/gwirelessclients(AP/RepeaterMode)• IEEE802.11n/gwirelessnetwork(Client/Bridge/RepeaterMode)• 10/100Ethernet

Web-based Configuration Utility Requirements

Computer with the following:• Windows®,Macintosh,orLinux-basedoperatingsystem• AninstalledEthernetadapter

Browser Requirements:• InternetExplorer®6.0andhigher• MozillaFirefox3.0andhigher• Google™Chrome2.0andhigher• AppleSafari3.0andhigher

Windows® Users: Make sure you have the latest version of Java installed. Visit www.java.com to download the latest version.

http://www.java.com/en/download/index.jsp



IntroductionD-Link,anindustryleaderinnetworking,introducesthenewD-LinkDAP-1360WirelessNOpenSourceAccessPoint.Withtheabilitytotransferfileswithamaximumwirelesssignalrateofupto300Mbps*,theDAP-1360givesyouhigh-speedwirelessnetwork access for your home or office.

TheDAP-1360isWi-FiIEEE802.11ncompliant,meaningthatitcanconnectandinteroperatewithother802.11ncompatiblewirelessclientdevices.TheDAP-1360isalsobackwardscompatiblewith802.11b/g.Itcanbeflexiblyconfiguredtooperatein7 different modes Access Point,Wireless Client,Bridge,Bridge with AP,Repeater,WISP Client Router or WISP Repeater. WithitsSetupWizard,theDAP-1360ensuresthatyouwillbeupandrunningonawirelessnetworkinjustamatterofminutes.

The DAP-1360 features Wi-Fi Protected Access (WPA-PSK/WPA2-PSK) to provide an enhanced level of security for wireless data communications. The DAP-1360 also includes additional security features to keep your wireless connection safe from unauthorized access.

TheDAP-1360supportsWPSontheAP,repeaterandwirelessclientoperationmodes,witheachcapableofbeingconvenientlyset up by using the PIN method or Push Button.

•Actualdata throughputwillvary.Networkconditionsandenvironmental factors, includingvolumeofnetwork traffic,buildingmaterialsandconstruction,andnetworkoverhead,loweractualdatathroughputrate.



TOTAL PERFORMANCECombines award winning access point features and 802.11n wireless technology to provide the best wireless performance.

TOTAL SECURITYThe most complete set of security features including WPA/WPA2 encryption to protect your network against outside intruders.

TOTAL COVERAGEProvides greater wireless signal rates even at farther distances for best-in-class Whole Home Coverage.

ULTIMATE PERFORMANCEThe D-Link Wireless N Open Source Access Point (DAP-1360) is an 802.11n compliant device that delivers real world performance of up to 13X faster than an 802.11g wireless connection (also faster than a 100Mbps wired Ethernet connection). Create a secure wireless networktosharephotos,files,music,video,printers,andnetworkstoragethroughoutyourhome.ConnecttheDAP-1360torouterandshareyourhigh-speedInternetaccesswitheveryoneonthenetwork.Inaddition,thisRangeExtenderincludesaQualityofService(QoS)enginethatkeepsdigitalphonecalls(VoIP)andonlinegamingsmoothandresponsive,providingabetterInternetexperience.

EXTENDED WHOLE HOME COVERAGEThis high performance Wireless Bridge provides superior Whole Home Coverage while reducing dead spots. The DAP-1360 is designed for use in bigger homes and for users who demand higher performance networking.

TOTAL NETWORK SECURITYTheDAP-1360supportsallofthelatestwirelesssecurityfeaturestopreventunauthorizedaccess,beitfromoverthewirelessnetworkor fromthe Internet.Support forWPAandWPA2standardsensurethatyou’llbeabletousethebestpossibleencryptionmethod,regardless of your client devices.

*MaximumwirelesssignalratederivedfromIEEEStandard802.11gand802.11nspecifications.Actualdatathroughputwillvary.Networkconditionsandenvironmentalfactors,includingvolumeofnetworktraffic,buildingmaterialsandconstruction,andnetworkoverhead,loweractualdatathroughputrate.Environmentalconditionswilladverselyaffect wireless signal range.



• FasterWirelessNetworking-TheDAP-1360providesupto300Mbps*wirelessconnectionwithother802.11nwirelessclients.Thiscapabilityallowsuserstoparticipateinreal-timeactivitiesonline,suchasvideostreaming,onlinegaming,and real-time audio.

• CompatiblewithIEEE802.11gDevices-TheDAP-1360isstillfullycompatiblewiththe802.11gstandards,soitcanconnectwithexisting802.11gPCI,USB,andCardbusadapters.

• AdvancedFirewallFeatures-The Web-based user interface displays advanced network management features including ContentFiltering,whichallowseasilyappliedcontentfilteringbasedonMACAddress.

• WPSPBC-(Wi-Fi Protected Setup Push Button Configuration) Push Button Configuration is a button that can be pressed toaddthedevicetoanexistingnetworkortocreateanewnetwork.Avirtualbuttoncanbeusedontheutilitywhilea physical button is placed on the side of the device.

This easy setup method allows you to form a secured wireless link between the DAP-1360 and another WPS enabled device. A PC is no longer needed to log into the Web-based interface.

• WPSPIN-(Wi-Fi Protected Setup Personal Identification Number ) A PIN is a unique number that can be used to add theaccesspointtoanexistingnetworkortocreateanewnetwork.ThedefaultPINmaybeprintedonthebottomoftheaccesspoint.Forextrasecurity,anewPINcanbegenerated.YoucanrestorethedefaultPINatanytime.OnlytheAdministrator (“admin” account) can change or reset the PIN.

• User-friendlySetupWizard-Throughitseasy-to-useWeb-baseduserinterface,theDAP-1360letsyoucontrolwhatinformationisaccessibletothoseonthewirelessnetwork,whetherfromtheInternetorfromyourcompany’sserver.Configure your access point to your specific settings within minutes.

Features



Hardware OverviewConnections

1 LAN Port Connect10/100Ethernetdevicessuchascomputers,switches,andhubs.

2 Power Receptor Receptor for the supplied power adapter.

3 Reset Button Pressing the Reset Button restores the access point to its original factory default settings.

1 2 3



Hardware OverviewLEDs

1

1 Power LED A solid green light indicates a proper connection to the power supply.

2 Wireless LED A solid green light indicates the wireless function is working. The light will be off during device reboot or if the wireless radio is disabled.

3 Security LED Asolidgreenlightindicatesthatwirelesssecurity(WEP,WPA,WPA2)isenabled.

4 LAN LED A solid green light indicates the LAN port connection is OK.

2 3 4



Hardware OverviewWPS LED/Button

1

1 WPS LED/Button A solid light indicates a successful WPS connection. A blinking light indicates the device is trying to establish a connection.


Section 2 - Installation

InstallationPleaseconfiguretheDAP-1360withacomputerconnecteddirectlytotheAP.Thenextfewpageswillexplainthedifferentoperational modes you can use.

Operation ModesDepending on how you want to use your DAP-1360 will determine which mode you use. This section will help you figure out which setting works with your setup.

• AccessPointmode-page13• WirelessClientmode-page14• Repeatermode-page15• Bridgemode-page16• BridgewithAPmode-page17• WISPClientRoutermode-page18• WISPRepeatermode-page19



Access Point ModeIntheAccessPointmode,theDAP-1360actsasacentralconnectionpointforanycomputer(client)thathasa802.11norbackward-compatible 802.11g wireless network interface and is within range of the AP. Clients must use the same SSID (wireless networkname)andchannelastheAPinordertoconnect.IfwirelesssecurityisenabledontheAP,theclientwillneedtoenterapasswordtoconnecttotheAP.InAccessPointmode,multipleclientscanconnecttotheAPatthesametime.

Internet Modem Router DAP-1360(in Access Point Mode)

Computer

Computer



Wireless Client ModeIntheWirelessClientmode,theDAP-1360actsasawirelessnetworkadapterforyourEthernet-enableddevice(suchasagameconsoleoraTVset-topbox).ConnectyourEthernet-enableddevicetotheAPusinganEthernetcable.TheAPClientmodecan support multiple wired clients.

IfyouaregoingtoconnectseveralEthernet-enableddevicestoyourDAP-1360,connecttheLANportoftheDAP-1360toanEthernetswitch,thenconnectyourdevicestothisswitch.

Example: Connect a gaming console using an ethernet cable to the DAP-1360. The unit is set to Wireless Client mode which will wirelessly connect to a wireless router on your network.

Internet Modem Router DAP-1360(in Wireless Client Mode)

Gaming Console



Repeater ModeInRepeatermode,theDAP-1360increasestherangeofyourwirelessnetworkbyextendingthewirelesscoverageofanotherAPorwirelessrouter.TheAPsandwirelessrouter(ifused)mustbewithinrangeofeachother.Makesurethatallclients,APs,andthewirelessrouterallusethesameSSID(wirelessnetworkname),channel,andsecuritysettings.

Computer

Internet Modem Router DAP-1360(In Repeater Mode)

Computer

Computer



Bridge ModeIntheBridgemode,theDAP-1360wirelesslyconnectsseperate localareanetworks(LANs)thatcan’teasilybeconnectedtogetherwithacable.Forexample,iftherearetwowiredLANsseparatedbyasmallcourtyard,itwouldbeexpensivetoburycables to connect between the two sides together. A better solution is to use two DAP-1360 units to wirelessly connect the twoLANs.IntheBridgemode,bothDAP-1360unitsdonotactasAPs.

Note: The Bridge mode is not specified in the Wi-Fi or IEEE standards. This mode will only work using two DAP-1360 units. Communication with other APs (even other D-Link APs) is not guaranteed.

Connecting Two Separate LANs Together Through Two DAP-1360 Units



Bridge with AP Mode

TheBridgewithAPmodeisthesameastheBridgemode,butinthiscase,theDAP-1360alsoactsasanAP.Clientswithwirelessinterfaces can wirelessly connect to the DAP-1360 and then connect to the other LAN that the DAP-1360 bridges to.

Note: The Bridge with AP mode is not specified in the Wi-Fi or IEEE standards. This mode will only work using two DAP-1360 units. Communication with other APs (even other D-Link APs) is not guaranteed.

ComputerComputer

Computer Computer

DAP-1360(In Bridge Mode with AP Mode)

DAP-1360(In Bridge Mode with AP Mode)

LAN 1 LAN 2

Connecting Two Separate LANs Together Through Two DAP-1360 Units(Wireless PCs Can Access the DAP-1360 Units)



WISP Client Router ModeIntheWISPClientRoutermode,theDAP-1360wirelesslyconnectstoaWISP(WirelessInternetServiceProvider)AP.Inthismode,theDAP-1360alsoactsasarouterforwiredclientsonyourLANandprovidesNAT(NetworkAddressTranslation)anda DHCP server to generate IP addresses for wired clients only. NAT and the DHCP server allow many computers to share the same wireless Internet connection.

IfyouareaWISPsubscriberandwanttoaccessyourWISPaccountusingwiredcomputers,connectyourcomputerstotheDAP-1360togetNAT,andthenconnectthemtotheWISPAP.

Internet

Computer

DAP-1360(In WISP Client Mode)WISP Outdoor AP

Connecting Wired PCs to the Internet Using the DAP-1360



WISP Repeater ModeIntheWISPRepeatermode,theDAP-1360wirelesslyconnectstoaWISP(WirelessInternetServiceProvider)AP.Inthismode,the DAP-1360 also acts as a router for both wireless and wired clients on your LAN. The WISP Repeater mode provides NAT (Network Address Translation) and a DHCP server to generate IP addresses for both wireless and wired clients. NAT and the DHCP server allow many computers to share the same wireless Internet connection.

IfyouareaWISPsubscriberandwanttouseyourWISPaccountinyourhouse,butthesignalsfromtheoutdoorWISPAParenotstrongenoughtoreachalloftheareasinthehouse,usetheDAP-1360tocanextendthesignalsfromtheoutdoorWISPAPandprovideaccesstowirelessclientsinyourhouse.Usingthismode,wirelessaswellaswiredclientscanconnecttotheoutdoor WISP AP through the DAP-1360.

Computer

Internet Modem Router DAP-1360(In Repeater Mode)

Computer

Computer

Connecting Wired and Wireless PCs to the Internet Using the DAP-1360



Wireless Installation ConsiderationsThe D-Link wireless access point lets you access your network using a wireless connection from virtually anywhere within the operatingrangeofyourwirelessnetwork.Keepinmind,however,thatthenumber,thicknessandlocationofwalls,ceilings,orotherobjectsthatthewirelesssignalsmustpassthrough,maylimittherange.TypicalrangesvarydependingonthetypesofmaterialsandbackgroundRF(radiofrequency)noiseinyourhomeorbusiness.Thekeytomaximizingwirelessrangeistofollow these basic guidelines:

1. Keep the number of walls and ceilings between the D-Link access point and other network devices to a minimum. Each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.

2.Be aware of the direct line between network devices. Awall that is 1.5 feet thick (.5meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.

3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on range.Trytopositionaccesspoints,wirelessaccesspoints,andcomputerssothatthesignalpassesthroughdrywalloropendoorways.Materialsandobjectssuchasglass,steel,metal,wallswithinsulation,water(fishtanks),mirrors,filecabinets,brick,andconcretewilldegradeyourwirelesssignal.

4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.

5. Ifyouareusing2.4GHzcordlessphonesorX-10(wirelessproductssuchasceilingfans,lights,andhomesecuritysystems),yourwirelessconnectionmaydegradedramaticallyordropcompletely.Makesureyour2.4GHzphonebase is as far away from your wireless devices as possible. The base transmits a signal even if the phone is not in use.


Section 3 - Configuration

ConfigurationThis section will show you how to configure your new D-Link wireless access point using the web-based configuration utility.

Web-based Configuration Utility

If you wish to change the default settings or optimize the performanceoftheDAP-1360,youmayusetheweb-basedconfiguration utility.

Toaccess theconfigurationutility,openawebbrowsersuch as Internet Explorer andenterhttp://dlinkap or http://192.168.0.50 in the address field.

Select Admin and then enter your password. Leave the password blank by default.

IfyougetaPageCannotbeDisplayederror,pleaserefertothe Troubleshooting section for assistance.



Click LaunchWirelessSetupWizard to configure your access point.

If you want to enter your settings without running the wizard,skiptopage34.

Wireless Setup Wizard

Click Next to continue.



This Wizard is designed to assist you in configuring your DAP-1360 as an access point.

Access Point Mode

Select Access Pointfromthedrop-downmenu.Then,click Next to continue.

Select WPS as the configuration method only if your wireless device supports Wi-Fi Protected Setup (WPS). For Manualsetup,skiptopage25.




Click Save to save your network settings.

In order for your network settings to take effect AP will reboot automatically.

When the device has finished rebooting the main screen will display.

Press down the Push Button on the Wireless device you are adding to your wireless network.



Select Manual as the configuration method to set up your network manually.


Enter a name for your wireless network (SSID).

Enter your network key. This key must be entered on your wireless clients.


The following screen will show you your network key to enter on your wireless clients.

Click Save to finish the Setup Wizard.



This Wizard is designed to assist you in configuring your DAP-1360 as a repeater.

Repeater Mode

Select Repeater from the drop-down menu.

Select WPS as the configuration method only if your wireless device supports Wi-Fi Protected Setup (WPS). For Manualsetup,skiptothenextpage.


Onthedeviceyouwant toconnect to, start thePBCprocessonthedevice.Youwillhave2minutestostartthe PBC process on both devices.



Select Manual configuration to setup your network manually.


If click Key in SSID,enterthenetworkname(SSID)ofthe network you want to connect to.

Findyourrouteroraccesspointfromthelist,clicktheradiobuttonintherightcolumn,andclickConnect.



Choose which Security Mode you want to use and click Next to continue.

If you select WEP,choosethekeytype(ASCIIorHEX),thekeysize(64or128-bit),andenterthewirelesssecuritypassword. Click Next to complete the Setup Wizard.

If you select WPA or WPA2,enterthewirelesssecuritypassword. Click Next to complete the Setup Wizard.



The Wireless Setup Wizard is complete. Click Finish to reboot the device.

If you select Auto,enterthewirelesssecuritypassword.Click Next to complete the Setup Wizard.



This Wizard is designed to assist you in configuring your DAP-1360 as a wireless client.

Wireless Client Mode

Select Wireless Client from the drop-down menu.

Select WPS as the configuration method only if your wireless device supports Wi-Fi Protected Setup (WPS). For Manualsetup,skiptothenextpage.


Onthedeviceyouwant toconnect to, start thePBCprocessonthedevice.Youwillhave2minutestostartthe PBC process on both devices.



Select Manual configuration to setup your network manually.


If click Key in SSID,enterthenetworkname(SSID)ofthe network you want to connect to.

Findyour accesspoint from the list, click the radiobuttonintherightcolumn,andclickConnect.



Choose which Security Mode you want to use and click Next to continue.

If you select WEP,choosethekeytype(ASCIIorHEX),thekeysize(64or128-bit),andenterthewirelesssecuritypassword. Click Next to complete the Setup Wizard.

If you select WPA or WPA2,enterthewirelesssecuritypassword. Click Next to complete the Setup Wizard.



The Wireless Setup Wizard is complete. Click Finish to reboot the device.

If you select Auto,enterthewirelesssecuritypassword.Click Next to complete the Setup Wizard.



Manual ConfigurationWireless Settings

YoumaymanuallyconfigureyourDAP-1360insteadofrunningthesetupwizard.

• AccessPointmode-page35• Repeatermode-page37• WirelessClientmode-page38• Bridgemode-page39• BridgewithAPmode-page40• WISPClientRoutermode-page41• WISPRepeatermode-page41



Enable Wireless:

Wireless Mode:

Wireless Network Name:

802.11 Mode:

Wireless Channel:

Enable Auto Channel Scan:

Checktheboxtoenablethewirelessfunction. Ifyoudonotwanttousewireless,unchecktheboxtodisableallthewirelessfunctions.Youmayalsosetupaspecifictime range (schedule). Select a schedule from the drop-down menu or click Add New to create a new schedule.

Select Access Point from the drop-down menu.

Whenyouarebrowsingforavailablewirelessnetworks,this is the name that will appear in the list (unless VisibilityStatusissettoInvisible,seebelow).ThisnameisalsoreferredtoastheSSID.Forsecuritypurposes,itis highly recommended to change from the default network name.

Select one of the following:802.11b Only - Select if you are only using 802.11b wireless clients.802.11g Only - Select if you are only using 802.11g wireless clients.802.11n Only - Select if you are only using 802.11n wireless clients.Mixed 802.11g and 802.11b - Select if you are using amixof802.11gand11bwirelessclients.Mixed 802.11n and 802.11g - Select if you are using amixof802.11nand11gwirelessclients.Mixed 802.11n, 802.11g and 802.11b-Selectifyouareusingamixof802.11n,11g,and11bwirelessclients.

IndicatesthechannelsettingfortheDAP-1360.TheChannelcanbechangedtofitthechannelsettingforanexistingwirelessnetworkortocustomizethewirelessnetwork.IfyouenableAutoChannelScan,thisoptionwillbegrayedout.

The Auto Channel Scan setting can be selected to allow the DAP-1360 to choose the channel with the least amount of interference.

Access Point Mode



Select the Channel Width:Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices.20MHz - Select if you are not using any 802.11n wireless clients.

ChecktheboxifyoudonotwanttheSSIDofyourwirelessnetworktobebroadcastedbytheDAP-1360.Ifchecked,theSSIDoftheDAP-1360 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DAP-1360 in order to connect to it.

Refer to page 65 for more information regarding the wireless security.

Channel Width:

Visibility Status:

Security Mode:



Enable Wireless:

Wireless Mode:

Site Survey:

Wireless NetworkName:

802.11 Mode:


Wireless Channel:

Channel Width:

Visibility Status:

Wireless SecurityMode:

Checktheboxtoenablethewirelessfunction.Ifyoudonotwanttousewireless,unchecktheboxtodisableallthewirelessfunctions.Youmayalsosetupaspecifictimerange (schedule). Select a schedule from the drop-down menu or click Add New to create a new schedule.

Select Repeater from the drop-down menu.

Click SiteSurvey to display a list of wireless networks inyourarea.Youmayselectthewirelessaccesspointto connect to.

Enter the SSID of the access point you want to repeat the signalof.Ifyoudonotknowforsure,clickSiteSurvey andselectitfromthelist,ifavailable.

Select the appropriate 802.11 mode based on the wireless clients in your network. The drop-down menu options are 802.11g Only,Mixed 802.11b/g,802.11b Only,802.11n Only,orMixed 802.11b/g/n.


The channel will automatically change to the channel of the AP you are connected to.

Select the appropriate channel width between 20MHz or Auto20/40MHz from the drop-down menu.

ChecktheboxifyoudonotwanttheSSIDtobebroadcastbytheDAP-1360.ThispreventstheSSIDfrombeingseenbysitesurveyutilities,soanywirelessclientswillhavetobepre-configuredwiththeSSIDoftheDAP-1360inordertoconnecttoit.

Select a wireless security setting. Options are None,WEP,WPA,orWPA2. See the Wireless Security section in this manual for a detailed explanationofthewirelesssecurityoptions.

Repeater Mode



Wireless Mode:Site Survey:

Wireless Type:


802.11 Mode:

Wireless Channel:


Channel Width:

Visibility Status:

Wireless MAC Clone:


WPS:

Select Wireless Client Mode from the drop-down menu.

Click SiteSurvey to display a list of wireless networks in your area.Youmayselectthewirelessaccesspointtoconnectto.Select Infrastructure if connecting to an access point or wireless router,or selectAd-Hoc if connecting to another wireless client.

Enter the SSID of the access point you want to repeat the signal of.Ifyoudonotknowforsure,clickSiteSurvey and select it fromthelist,ifavailable.


The channel will automatically change to the channel of the AP you are connected to.


Select the appropriate channel width between 20MHz or Auto 20/40MHz from the drop-down menu.


YoucanclonethewirelessMACaddresstoconnectthedevice.

Select a wireless security setting. Options are None,WEP,WPA,orWPA2. See the Wireless Security section in this manual for a detailed explanationofthewirelesssecurityoptions.

Select enable if you want to configure the DAP-1360 with Wi-Fi Protection setup.

Wireless Client Mode



Enable Wireless:

Wireless Mode:


802.11 Mode:

Wireless Channel:


Channel Width:

Visibility Status:

Remote AP MAC:

Bridge Security:

Select this to turn the Wi-Fi module on and off. Use the drop-downboxtoselectifyouwanttouseaschedule.Click Add New to add or change a schedule.

Select Bridge from the drop-down menu.

The Wireless Network Name is a unique name that identifies a network. All devices on a network must share the same wireless network name in order to communicate on the network. If you decide to change the wireless networknamefromthedefaultsetting,enteryournewwireless network name in this field.


All devices on the network must share the same channel.



Select the transmission rate. It is strongly suggested to use the Auto setting for optimal performance.

Enter the MAC addresses of the APs in your network that will serve as bridges to wirelessly connect multiple networks.

Select None to disable encryption to across the network. Select WEP 64-bit or WEP 128-bit to limit communication to only those devices that share the same WEP settings. Select WPA-PSK or WPA2-PSK to secure your network using a password and dynamic key changes (No RADIUS server required).

Bridge Mode

Note: The Bridge mode is not completely specified in the Wi-Fi or IEEE standards. This mode can work with other DAP-1360 units. Communication with other APs (even other D-Link APs) is not guaranteed.



Enable Wireless:

Wireless Mode:


802.11 Mode:

Wireless Channel:

Enable Auto Scan:

Channel Width:

Visibility Status:

Remote AP MAC:

Bridge Security:

Select this to turn the Wi-Fi module on and off. Use the drop-downboxtoselectifyouwanttouseaschedule.Click Add New to add or change a schedule.

Select Bridge with AP from the drop-down menu.

The Wireless Network Name is a unique name that identifies a network. All devices on a network must share the same wireless network name in order to communicate on the network. If you decide to change thewirelessnetworkname fromthedefault setting,enter your new wireless network name in this field.


All devices on the network must share the same channel.




Enter the MAC addresses of the APs in your network that will serve as bridges to wirelessly connect multiple networks.

Select None to disable encryption to across the network. Select WEP 64-bits or WEP 128-bits to limit communication to only those devices that share the same WEP settings. Select WPA-PSK or WPA2-PSK to secure your network using a password and dynamic key changes (No RADIUS server required).

Bridge with AP Mode

Note: The Bridge with AP mode is not completely specified in the Wi-Fi or IEEE standards. This mode can work with other DAP-1360 units. Communication with other APs (even other D-Link APs) is not guaranteed.



Enable Wireless:

Wireless Mode:

Site Survey:


802.11 Mode:

Wireless Channel:

Enable Auto Scan:

Channel Width:

Visibility Status:


Select this to turn the Wi-Fi module on and off. Use thedrop-downbox to select if youwant touse a schedule. Click Add New to add or change a schedule.

Select WISP Client or WISP Repeater from the drop-down menu.

Click this button to choose the root AP from an available connection list. If the root AP has wireless encryption, youhave touse the samewirelesssecurity mode to connect the root AP.

Youcan input thewirelessnetworknameof theroot AP or click the SiteSurvey button to find the root AP.


The channel used will be displayed. The channel will follow the root AP.




Selectawirelesssecuritysetting.OptionsareNone,WEP,WPA,orWPA2.RefertotheWireless Security section of this manual for adetailedexplanationofthewirelesssecurityoptions.

WISP Client Router/WISP Repeater Modes



WAN SettingsDynamic IP (DHCP)

WAN settings are only used in the WISP Client Router wireless mode and the WISP Repeater wireless mode. Choose Dynamic IP(DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP number to use. This option is commonly used for Cable modem services.

Host Name:

MTU Size:

Attain DNS Automatically:

Set DNS manually:

DNS Server:

Clone MAC Address:

The Host Name is optional but may be required by some ISPs.

YoumayneedtochangetheMTU(MaximumTransmission Unit) for optimal performance with your specific ISP. The default MTU size is 1500.

Select this option if you want the DAP-1360 to get the DNS (Domain Name System) server IP address automatically.

Select this option if you want to manually enter the DNS Server IP address(es). The fields to enter the Primary and Secondary DNS server IP addresses will appear after you have selected this option.

Enter the Primary and Secondary DNS server IP address assigned by your ISP.

ThedefaultMACaddressissettotheEthernetMACaddressyourDAP-1360.YoucanclicktheCloneYourPC’sMACAddressbuttonto replace the AP’s MAC address with the MAC address of the PC that you used to register with your ISP. It is not recommended that you change the default MAC address unless required by your ISP.



Static IP

SelectStaticIPifallWANIPinformationisprovidedtoyoubyyourISP.YouwillneedtoenterintheIPaddress,subnetmask,gatewayaddress,andDNSaddress(es)providedtoyoubyyourISP.

IP Address:

Subnet Mask:

Default Gateway:

MTU Size:

Primary DNS Server:

Secondary DNS Server:

Clone MAC Address:

192.168.1.1 is the default WAN IP Address of the DAP-1360.

255.255.255.0 is the default subnet mask. All devices on the network must have the same subnet mask to communicate on the network.

Enter the IP Address of the gateway in your network.


Enter the Primary DNS (Domain Name System) server IP address assigned by your ISP.

Enter the Secondary DNS (optional) server IP address assigned by your ISP.

ThedefaultMACaddressissettotheMACaddressontheAP(AccessPoint).YoucanclicktheCloneYourPC’sMACAddressbutton to replace the AP’s MAC address with the MAC address of your Ethernet card. It is not recommended that you change the default MAC address unless required by your ISP.



PPPoESelectPPPoE(Point-to-PointProtocoloverEthernet) ifyour ISPusesaPPPoEconnection.Your ISPwillprovideyouwithausername and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through the DAP-1360.

Username:

Password:

Service Name:

Reconnection Type:

Maximum Idle Time:

MTU Size:

AttainDNS Automatically:

Set DNS Manually:

DNS Servers:

Clone MAC Address:

Enter your PPPoE user name.

Enter your PPPoE password and then retype the passwordinthenextbox.

Enter the ISP Service Name (optional).

Select Always on,On demand,orManual.

Enter amaximum idle timeduringwhich theInternet connection is maintained during inactivity.

Youmayneed to change theMTU (MaximumTransmission Unit) for optimal performance with yourspecificISP.Themaximum/defaultMTUsizeis 1492.

Select this option if you want the DAP-1360 to get the DNS (Domain Name System) server IP address automatically.

Select this option if you want to manually enter the DNS Server IP address(es). Fields to enter the Primary and Secondary DNS server IP addresses will appear after you select this option.

Enter the Primary and Secondary DNS server IP address assigned by your ISP.

ThedefaultMACaddressissettotheMACaddressontheAP(AccessPoint).YoucanclicktheClone Your PC’s MAC Address button to replace the AP’s MAC address with the MAC address of your Ethernet card. It is not recommended that you change the default MAC address unless required by your ISP.



PPTPChoosePPTP(Point-to-PointTunnelingProtocol)ifyourISPusesaPPTPconnection.YourISPwillprovideyouwithausernameand password. This option is typically used for DSL services.

PPTP IP Address:

PPTP Subnet Mask:

PPTP Server IP Address:

Username:

Password:

MTU Size:

Attain DNS Automarically:

Set DNS Automatically:

DNS Servers:

Clone MAC Address:

Enter the IP address (Static PPTP only).

Enter the subnet mask.

Enter the Server IP Address provided by your ISP.

Enter your PPTP username.

Enter your PPTP password and then retype thepasswordinthenextbox.


Select this option if you want the DAP-1360 get DNS server IP address automatically.

Select this option if you want to manually enter the DNS Server IP address(es). Fields to enter the Primary and Secondary DNS server IP addresses will appear after you select this option.

Enter the Primary and Secondary DNS (Domain Name System) server IP address assigned by your ISP.

ThedefaultMACaddressissettotheMACaddressontheAP(AccessPoint).YoucanclicktheClone Your PC’s MAC Address button to replace the AP’s MAC address with the MAC address of your Ethernet card. It is not recommended that you change the default MAC address unless required by your ISP.



LAN SettingsThis section will allow you to change the local network settings of the access point and to configure the DHCP settings.

Device Name:

LAN Connection Type:

My IPv6 Connection Type:

Enter the Device Name of the AP. It is recommended to change the Device Name if there is more than one D-Link device within the subnet.

Use the drop-down menu to select Dynamic IP (DHCP) to automatically obtain an IP address on the LAN/private network.

Select from the drop-down menu the type of IPv6 connection you would like to use.



Device Name:

LAN Connection Type:

IP Address:

Subnet Mask:

Default Gateway:

Enter the Device Name of the AP. I t is recommended to change the Device Name if there is more than one D-Link device within the subnet.Youcanenter thedevicenameof theAP into your web browser to access the instead of IP address for configuration. If you are using thedevicenametoconnect,ensurethatyourPC and your DAP-1360 are on the same network.

Select Static IP from the drop-down menu.

Enter the IP address of the access point. The default IP address is 192.168.0.50. If you change the IPaddress,onceyouclickApply, youwillneed to enter the new IP address in your browser to get back into the configuration utility.

Enter the Subnet Mask assigned by your ISP.

EntertheGatewayassignedbyyourISP.

Static IPSelectStaticIPAddressifalltheInternetport’sIPinformationisprovidedtoyoubyyourISP.YouwillneedtoenterintheIPaddress,subnetmask,gatewayaddress,andDNSaddress(es)providedtoyoubyyourISP.EachIPaddressenteredinthefieldsmustbeintheappropriateIPform,whicharefouroctetsseparatedbyadot(x.x.x.x).TheAccesspointwillnotaccepttheIPaddress if it is not in this format.



AdvancedAdvanced Wireless

Transmit Power:

WMM Enable:

Short GI:

IGMP Snooping:

WLAN Partition:

HT 20/40 Coexistance:

Sets the transmit power of the antennas.

WMMisQoS foryourwirelessnetwork.Thiswillimprove the quality of video and voice applications for your wireless clients.

Checkthisboxtoreducetheguardintervaltimethereforeincreasingthedatacapacity.However,it’s less reliable and may create higher data loss.

This enables IGMP snooping for thewirelessconnection. We recommend enabling this if you often use multicast services such as video conferencing and streaming audio/video.

This featureenablesclient isolation. Ifenabling,all clients will not be able to view or access each other’s information or within the network.

Check to enable or disable this feature.



MAC Address FilterThe MAC address filter section can be used to filter network access by machines based on the unique MAC addresses of their network adapter(s). It is most useful to prevent unauthorized wireless devices from connecting to your network. A MAC address is a unique ID assigned by the manufacturer of the network adapter.

Configure MAC Filtering:

Add MAC Filtering

Rule:

When Turn MAC Filtering OFFisselected,MACaddressesare not used to control network access. When Turn MAC Filtering ON and ALLOW computers listed to access the networkisselected,onlycomputerswithMACaddresseslisted in the MAC Address List are granted network access. When Turn MAC Filtering ON and DENY computers listed to access the network isselected,anycomputerwithaMAC address listed in the MAC Address List is refused access to the network.

This parameter allows you to manually add a MAC filtering rule. Click the Add button to add the new MAC filtering rule to the MAC Filtering Rules list at the bottom of this screen.



Wi-Fi Protected Setup

Checkthisboxtoenablethefunction

Locking the wireless security settings prevents the settings from being changed by the Wi-Fi Protected Setup feature of the router. Devices can still be added tothenetworkusingWi-FiProtectedSetup.However,the settings of the network will not change once this option is checked.

Press the button to generate a new PIN or Reset to Default.

Shows the current value of the router’s PIN.

Restore the default PIN of the access point.

Create a random number that is a valid PIN. This becomestherouter’sPIN.YoucanthencopythisPINto the user interface of the registrar.

Press the button to start with the wizard to setup the WPS.

Enable:

Lock Wireless Security Settings:

Pin Settings:

Current PIN:

Reset PIN to Default:

Generate New PIN:

Add Wireless Station:

Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the “Initial setup” as well as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certified it across different products as well as manufactures. Theprocessisjustaseasy,asdepressingabuttonforthePush-ButtonMethodorcorrectlyenteringthe8-digitcodeforthePin-CodeMethod.Thetimereductioninsetupandeaseofusearequitebeneficial,whilethehighestwirelessSecuritysettingof WPA2 is automatically used.



User Limits

Check the Enable User Limitbox toenable thisfeature.

Enterthemaximumnumberofclients,between1and 32.

Click SaveSettings to save and activate the new changes.

Enable User Limit:

User Limit:

Save Settings:

Enterthemaximumnumberofwirelessclientsthatcanconnectatonetimetoyouraccesspoint.



Port Forwarding (WISP modes only)

Checktheboxtoconfigureaportforwardingrule.

Enter a name for the rule.You can select anapplication name from the Application Name drop-down menu. Click the << button to fill in the Name field with the application name that you selected.

Enter the IP address of the computer on your local network that you want to allow the incoming service to.

Enter the port or ports that you want to open. If youwanttoopenoneport,enterthesameportinbothboxes.

Select TCP,UDP,orBoth.

Port ForwardingRules:

Name:

IP Address:

Start/End Ports:

Traffic Type:

This function is available if your DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature allows you to open a single port or a range of ports. Click SaveSettings and the port forwarding rule will be put into the Port Forwarding List.



Port Filter (WISP modes only)

Checktheboxtoconfigureaportfilterrule.

Enter a name for the rule.You can select anapplication name from the Application Name drop-down menu. Click the << button to fill in the Name field with the application name that you selected.

Enter the port or ports that you want to open. If youwanttoopenoneport,enterthesameportinbothboxes.

Select TCP,UDP,orBoth.

Port FilterRules:

Name:

Start/End Ports:

Traffic Type:

This function is available if your DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature is used to secure or restrict your local network. It will deny the ports that you enter from the local network to the Internet. Click SaveSettings and the port filter rule will be put into the Port Filter List.



DMZ (WISP modes only)

CheckthisboxtoenableDMZ.

Enter the IP address of the computer you would liketoopenallportsto.Youcanselectacomputerfrom the Computer Name drop-down menu and click << to enter the computer name into the DMZ Host IP Address field.

Enable DMZ:

DMZ Host IP Address:

This function is available only if the DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature allows you to set up a DMZ (Demilitarized Zone) host. If you have a client PC that cannot run Internet applications properly from behind the DAP-1360,thenyoucansettheclientupforunrestrictedInternetaccess.TheDMZallowsacomputertobeexposedtotheInternet. This feature is useful for gaming purposes. Enter the IP address of the computer that will be the DMZ host. Adding a clienttotheDMZmayexposeyourlocalnetworktoavarietyofsecurityrisks,soonlyusethisoptionasalastresort.



Parental Control (WISP modes only)

Select Turn Website Filtering OFF or Turn Website Filtering ON and DENY computers access to ONLY these sites.

Enter a keyword or URL that you want to block and click SaveSettings. Any URL that contains the keyword will be blocked.

Configure Website

Filtering Below:

Website URLAddress:

This function is available only if the DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature allows you to create a list of websites that you want to deny users access.



Advanced Network (WISP modes only)

CheckthisboxtousetheUniversalPlugandPlay(UPnP™)feature.UPnPprovidescompatibilitywithnetworkingequipment,softwareandperipherals.

Check this box to allow theWANport of the DAP-1360 tobepinged.Unchecking theboxwill not allow the DAP-1360 to respond to pings. Blockingpingresponsemayprovidesomeextrasecurity from intruders.

Remote management allows the DAP-1360 to be configured from the Internet by a web browser. A username and password are still required to access theWeb-Managementinterface.Ingeneral,onlyamember of your network can browse the built-in web pages to perform Administrator tasks. This feature enables you to perform Administrator tasks from the remote (Internet) host.

Enable UPnP:

Enable WAN Ping Respond:

Remote Management:

This function is available if the DAP-1360 is in WISP Client Router or WISP Repeater mode. This feature allows you to change the LAN settings. Please be aware that any changes to the factory default settings may affect the behavior of your network.



Password:

Confirm Password:

Enable Graphical

Authentication:

Enter a new password for the Administrator Login Name. The administrator can make changes to the settings.

Enter the same password that you entered in the previoustextboxinordertoconfirmitsaccuracy.

Check to enable this feature.

MaintenanceAdmin

This page will allow you to change the Administrator password. The administrator password has read/write access.



Save to Local Hard Drive:

Upload from Local Hard Drive:

Restore to Factory Default:

Reboot the Device:

Use this option to save the current access point configuration settings to a file on the hard disk of the computer you are using. Click the Savebutton.Youwillthen see a file dialog where you can select a location and file name for the settings.

Use this option to load previously saved access point configuration settings. Click Browse to find a previously savedconfigurationfile.Then, click theUpload Settings button to transfer those settings to the access point.

This option will restore all configuration settings back to the settings that were in effect at the time the access point was shipped from the factory. Any settings that havenotbeensavedwillbelost,includinganyrulesthat you have created. If you want to save the current accesspoint configuration settings, use theSave button above.

Note: Restoring the factory default settings will not reset the Wi-Fi Protected Status to Not Configured.

Click to reboot the access point.

System



FirmwareUpgrade:

Browse:

Upload:

Click on Check Now to find out if there is an updated firmware; if so,download thenewfirmware toyourhard drive.

Afteryouhavedownloadedthenewfirmware,clickBrowse to locate the firmware update on your hard drive. Click Upload to complete the firmware upgrade.

Onceyouhaveafirmwareupdateonyourcomputer,use this option to browse for the file and then upload the information into the access point.

FirmwareYoucanupgradethefirmwareoftheaccesspointhere.Makesurethefirmwareyouwanttouseisonthelocalharddriveofthe computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support website forfirmwareupdatesathttp://support.dlink.com.Youcandownloadfirmwareupgradestoyourharddrivefromthissite.

Afteryouhavedownloadedthenewlanguagepack,click Browse to locate the language pack file on your hard drive. Click Upload to complete the language pack upgrade.

Language PackYoucanchangethelanguageofthewebUIbyuploadingavailable language packs.

Browse:



Watchdog

Enable Watchdog(Ping of Life):

Update TimeInterval:

Watchdog ResponseIP:

Enable Mail Alert:

SMTP Server:

Sender E-Mail:

Receiver E-Mail:

EnableAuthentication:

Account Name:

Password:

CheckthisboxtoenabletheWatchdog(Pingof Life) to check some host IP.

Enter the time interval of how often you would like the Watchdog to ping the response IP address.

Enter the IP address that the Watchdog will ping.

Checkthisboxtoenablee-mailnotificationforthe Watchdog.

Enter the SMTP server IP address.

Enter the e-mail address from which thenotification will be sent.

Enter the e-mail address which the notification will be sent to.

ChecktheboxtoenableauthenticationthatisusedwiththeSMTPserver.

Enter your account name that is used with the SMTP server.

EnteryourpasswordthatisusedwiththeSMTPserverandre-enteritinthenextbox.

TheWatchdogfeaturepingsaspecifiedIPaddress.IftheIPaddressstopsrespondingtopings,yourAPwillberebooted.Youcan also select an option to have the DAP-1360 send an e-mail alert if the specified IP address stops responding to pings.



Time Zone:

Daylight Saving:

Enable NTP Server:

NTP Server Used:

Date and Time:

Select the Time Zone from the drop-down menu.

ToselectDaylightSavingtimemanually,clicktheEnableDaylightSavingcheckbox.Nextusethedrop-down menu to select a Daylight Saving Offset and then enter a start date and an end date for daylight saving time.

NTP is short for Network Time Protocol. NTP synchronizes computer clock times in a network ofcomputers.CheckthisboxtouseaNTPserver.ThiswillonlyconnecttoaserverontheInternet,not a local server.

Enter the NTP server or select one from the drop-down menu.

Tomanually input the time,enter thevalues inthesefieldsfortheYear,Month,Day,Hour,Minute,and Second and then click SaveSettings.Youcan also click the Copy Your Computer’s Time Settings button at the bottom of the screen.

TimeTheTimeConfigurationoptionallowsyoutoconfigure,update,andmaintainthecorrecttimeontheinternalsystemclock.From this section you can set the time zone that you are in. Daylight Saving can also be configured to automatically adjust the time when needed.



System Check

Ping Test /IPv6 Ping Test:

Ping Result:

The Ping Test / IPv6 Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the host name or IP/IPv6 address that you wishtoPing,andclickPing.

The results of your ping attempts will be displayed here.

This section Ping Tests by sending ping packets to test if a computer on the internet is running and responding.



Schedules

Enter a name for your new schedule.

Select aday, a rangeofdays, orAllWeek toinclude every day.

Enter a start and end time for your schedule.

The list of schedules will be listed here. Click the Edit icon to make changes or click the Delete icon to remove the schedule.

Name:

Days:

Time:

Schedule Rules List:



General:

LAN:

Wireless LAN:

Displays the access point’s time and firmware version.

Displays the MAC address and the private (local) IP settings for the access point.

Displays the wireless MAC address and your wireless settings such as SSID and Channel.

StatusDevice Info

This page displays the current information for the DAP-1360. It will display the LAN and wireless LAN information.



Log Options:

First Page:

Last Page:

Previous Page:

Next Page:

Clear Log:

Log Settings:

Refresh:

There are several types of logs that can be viewed: SystemActivity,Debug Information,Attacks,Dropped Packets and Notice.

This button directs you to the first page of the log.

This button directs you to the last page of the log.

This button directs you to the previous page of the log.

Thisbuttondirectsyoutothenextpageofthelog.

This button clears all current log content.

This button opens a new menu where you can configure the log settings.

This button refreshes the log.

LogsTheDAP-1360keepsarunninglogofeventsandactivitiesoccurringontheAP.IftheAPisrebooted,thelogsareautomaticallycleared.YoucansavethelogfilesunderLogSetting.



StatisticsTheDAP-1360keepsstatisticsofthetrafficthatpassesthroughit.YoucanviewtheamountofpacketsthatpassthroughtheLANand wireless portions of the network. The traffic counter will reset if the access point is rebooted.



WirelessThe wireless section allows you to view the wireless clients that are connected to your wireless access point.

Connection Time:

MAC Address:

Displays the amount of time the wireless client has been connected to the access point.

The Ethernet ID (MAC address) of the wireless client.



IPv6This page displays all your IPv6 internet and network connection information.



Help


Section 4 - Security

Wireless SecurityThis section will show you the different levels of security you can use to protect your data from intruders. The DAP-1360 offers the following types of security:

•WPA2(Wi-FiProtectedAccess2) •WPA2-PSK(Pre-SharedKey)•WPA(Wi-FiProtectedAccess) •WPA-PSK(Pre-SharedKey)



What is WPA?WPA,orWi-FiProtectedAccess,isaWi-FistandardthatwasdesignedtoimprovethesecurityfeaturesofWEP(WiredEquivalentPrivacy).

The 2 major improvements over WEP:

•ImproveddataencryptionthroughtheTemporalKeyIntegrityProtocol(TKIP).TKIPscramblesthekeysusingahashingalgorithmand,byaddinganintegrity-checkingfeature,ensuresthatthekeyshaven’tbeentamperedwith. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.

•Userauthentication,whichisgenerallymissinginWEP,throughtheextensibleauthenticationprotocol(EAP).WEPregulatesaccesstoawirelessnetworkbasedonacomputer’shardware-specificMACaddress,whichisrelatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network.

WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between8and63characterslong.Thepasswordcanincludesymbols(!?*&_)andspaces.Thiskeymustbetheexactsamekeyentered on your wireless bridge or access point.

WPA/WPA2incorporatesuserauthenticationthroughtheExtensibleAuthenticationProtocol(EAP).EAPisbuiltonamoresecure public key encryption system to ensure that only authorized network users can access the network.



Configure WPA/WPA2 Personal

It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish wirelessconnectivitybeforeenablingencryption.Yourwirelesssignalmaydegradewhenenablingencryptionduetotheadded overhead.

1. Log into the web-based configuration by opening a web browser and entering the IP address of the access point (192.168.0.50). Click on Setup and then click Wireless Settings on the left side.

2.Next toSecurity Mode, selectEnable WPA Wireless Security,Enable WPA2 Wireless Security,orEnable WPA2-Auto Wireless Security.

3.NexttoCipher Type,selectTKIP,AES,orAuto.

4.NexttoPSK / EAP,selectPersonal.

5.NexttoPassphrase,enterakey.ThekeyisenteredasapassphraseinASCIIformatatbothendsofthewirelessconnection.The passphrase must be between 8-63 characters.

6. Click SaveSettings at the top of the window to save your settings. If you are configuring the access point with a wireless adapter,youwillloseconnectivityuntilyouenableWPA-PSKonyouradapterandenterthesamepassphraseasyoudidonthe access point.



It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish wirelessconnectivitybeforeenablingencryption.Yourwirelesssignalmaydegradewhenenablingencryptionduetotheadded overhead.

1. Log into the web-based configuration by opening a web browser and entering the IP address of the access point (192.168.0.50). Click on Setup and then click Wireless Settings on the left side.

2.NexttoSecurity Mode,selectEnable WPA Wireless Security,Enable WPA2 Wireless Security,orEnable WPA2-Auto Wireless Security.

3.NexttoCipher Mode,selectTKIP,AES,orAuto.

4.NexttoPersonal / Enterprise,selectEnterprise.

5.NexttoRADIUS Server,entertheIPAddressofyourRADIUSserver.

6.NexttoPort,entertheportyouareusingwithyourRADIUSserver.1812 is the default port.

7.NexttoShared Secret,enterthesecuritykey.

8. Click SaveSettings to save your settings.

Configure WPA/WPA2 Enterprise


Section 5 - Connecting to a Wireless Network

Connect to a Wireless NetworkUsing Windows® XP

Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows®2000,pleaserefertotheusermanualofyourwirelessadapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.

Right-click on the wireless computer icon in your system tray (lower-right cornernext to the time). SelectViewAvailableWireless Networks.

If you receive the Wireless Networks Detectedbubble,clickonthe center of the bubble to access the utility.

or

The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button.

Ifyougetagoodsignal,butcannotaccesstheInternet,checkyouTCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.



Configure WPA-PSK

It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter. If you are joininganexistingnetwork,youwillneedtoknowtheWEPkeybeingused.

2. Highlight the wireless network (SSID) you would like to connect to and click Connect.

1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). SelectViewAvailableWirelessNetworks.



3. The Wireless Network Connection boxwillappear.EntertheWPA-PSKpassphrase and click Connect.

It may take 20-30 seconds to connect to the wireless network. If the connectionfails,pleaseverifythattheWPA-PSKsettingsarecorrect.TheWPA-PSKpassphrasemustbeexactlythesameasonthewirelessaccesspoint.



Using Windows Vista®

Windows Vista®usersmayusetheconvenient,built-inwirelessutility.Followtheseinstructions:

From theStartmenu,go toControlPanel, and thenclickonNetwork and Sharing Center.

The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) under Select a network to connect to and then click the Connect button.



Click Connect Anyway to continue.

The utility will display the following window to indicate a connection is being made.

The final window indicates the establishment of a successful connection.

Thenexttwopagesdisplaythewindowsusedtoconnecttoeithera WEP or a WPA-PSK wireless network.



Click on a network (displayed using the SSID) using WPA-PSK under Select a network to connect to and then click the Connect button.

Enter the appropriate security key or passphrase in the field provided and then click the Connect button.

Configure WPA-PSK

It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter. If you are joininganexistingnetwork,youwillneedtoknowtheWEPkeybeingused.



Using Windows® 7It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wirelessadapter.Ifyouarejoininganexistingnetwork,youwillneedtoknowthesecuritykeyorpassphrasebeingused.

1. Click on the wireless icon in your system tray (lower-right corner).

2. The utility will display any available wireless networks in your area.

Wireless Icon



3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button.

IfyougetagoodsignalbutcannotaccesstheInternet,checkyourTCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.

4. The following window appears while your computer tries to connect to the router.



5. Enter the same security key or passphrase that is on your router and click Connect.Youcanalsoconnectbypushing theWPSbutton on the router.

It may take 20-30 seconds to connect to the wireless network. If the connectionfails,pleaseverifythatthesecuritysettingsarecorrect.Thekeyorpassphrasemustbeexactlythesameasonthewirelessrouter.



Configure WPSThe WPS feature of the DAP-1360 can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to configure the WPS feature of the DAP-1360:

1. Click the Start button and select Computer from the Start menu.

2. Click the Network option.



3. Double-click the DAP-1360.

4. Input the WPS PIN number (displayed in the WPS window on the Router’s LCD screen or in the Setup > Wireless Setup menu in the Router’s Web UI) and click Next.



5. Type a name to identify the network.

6.Toconfigureadvancedsettings,clicktheicon.




7. The following window appears while the Router is being configured.

Wait for the configuration to complete.

8. The following window informs you that WPS on the DAP-1360 has been setup successfully.

Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future.

9. Click Close to complete WPS setup.


Section 6 - Troubleshooting

TroubleshootingThis chapter provides solutions to problems that can occur during the installation and operation of the DAP-1360. Read the followingdescriptionsifyouarehavingproblems.(TheexamplesbelowareillustratedinWindows® XP. If you have a different operatingsystem,thescreenshotsonyourcomputerwilllooksimilartothefollowingexamples.)

1. Why can’t I access the web-based configuration utility?

WhenenteringtheIPaddressoftheD-Linkaccesspoint(192.168.0.50forexample),youarenotconnectingtoawebsiteontheInternetorhavetobeconnectedtotheInternet.Thedevicehastheutilitybuilt-intoaROMchipinthedeviceitself.Yourcomputer must be on the same IP subnet to connect to the web-based utility.

•MakesureyouhaveanupdatedJava-enabledwebbrowser.Werecommendthefollowing:

-MicrosoftInternetExplorer®6.0andhigher-MozillaFirefox3.0andhigher-Google™Chrome2.0andhigher- Apple Safari 3.0 and higher

•Verifyphysicalconnectivitybycheckingforsolidlinklightsonthedevice.Ifyoudonotgetasolidlinklight,tryusingadifferentcableorconnecttoadifferentportonthedeviceifpossible.Ifthecomputeristurnedoff,thelinklightmaynotbeon.

•Disableanyinternetsecuritysoftwarerunningonthecomputer.SoftwarefirewallssuchasZoneAlarm,BlackIce,Sygate,NortonPersonalFirewall,andWindows® XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it.



•ConfigureyourInternetsettings:

•GotoStart > Settings > Control Panel. Double-click the Internet Options Icon.FromtheSecuritytab,clickthe button to restore the settings to their defaults.

•ClicktheConnectiontabandsetthedial-upoptiontoNeverDialaConnection.ClicktheLANSettingsbutton.Make sure nothing is checked. Click OK.

•GototheAdvancedtabandclickthebuttontorestorethesesettingstotheirdefaults.ClickOKthreetimes.

•Closeyourwebbrowser(ifopen)andopenit.

•Accessthewebmanagement.OpenyourwebbrowserandentertheIPaddressofyourD-Linkaccesspointintheaddressbar. This should open the login page for your the web management.

•Ifyoustillcannotaccesstheconfiguration,unplugthepowertotheaccesspointfor10secondsandplugbackin.Waitabout30secondsandtryaccessingtheconfiguration.Ifyouhavemultiplecomputers,tryconnectingusingadifferentcomputer.

2. What can I do if I forgot my password?

Ifyouforgotyourpassword,youmustresetyouraccesspoint.Unfortunatelythisprocesswillchangeallyoursettingsbacktothe factory defaults.

Toresettheaccesspoint,locatetheresetbutton(hole)ontherearpaneloftheunit.Withtheaccesspointpoweredon,useapaperclip to hold the button down for 10 seconds. Release the button and the access point will go through its reboot process. Waitabout30secondstoaccesstheaccesspoint.ThedefaultIPaddressis192.168.0.50.Whenloggingin,theusernameisAdminandleavethepasswordboxempty.



3.Whycan’tIconnecttocertainsitesorsendandreceiveemailswhenconnectingthroughmyaccesspoint?

Ifyouarehavingaproblemsendingorreceivingemail,orconnectingtosecuresitessuchaseBay,bankingsites,andHotmail,wesuggestloweringtheMTUinincrementsoften(Ex.1492,1482,1472,etc).

Note: AOL DSL+ users must use MTU of 1400.

TofindtheproperMTUSize,you’llhavetodoaspecialpingofthedestinationyou’retryingtogoto.Adestinationcouldbeanothercomputer,oraURL.

•ClickonStart and then click Run.

•Windows®95,98,andMeuserstypeincommand(Windows®NT,2000,andXPuserstypeincmd)andpressEnter (or click OK).

•Oncethewindowopens,you’llneedtodoaspecialping.Usethefollowingsyntax:

ping [url] [-f ] [-l] [MTU value]

Example:ping yahoo.com -f -l 1472



Youshouldstartat1472andworkyourwaydownby10eachtime.Onceyougetareply,goupby2untilyougetafragmentedpacket.Takethatvalueandadd28tothevaluetoaccountforthevariousTCP/IPheaders.Forexample,letssaythat1452wasthepropervalue,theactualMTUsizewouldbe1480,whichistheoptimumforthenetworkwe’reworkingwith(1452+28=1480).

OnceyoufindyourMTU,youcannowconfigureyouraccesspointwiththeproperMTUsize.

To change the MTU rate on your access point follow the steps below:

•Openyourbrowser,entertheIPaddressofyouraccesspoint(192.168.0.50)andclick OK.

•Enteryourusername(Admin)andpassword(blankbydefault).ClickOK to enter the web configuration page for the device.

•ClickonSetup and then click Manual Configure.

•TochangetheMTUenterthenumberintheMTUfieldandclickSaveSettings to save your settings.

• Testyouremail.IfchangingtheMTUdoesnotresolvetheproblem,continuechangingtheMTUinincrementsof ten.


Appendix A - Wireless Basics

D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivitywithinyourhome,businessorpublicaccesswirelessnetworks.StrictlyadheringtotheIEEEstandard,theD-Linkwirelessfamilyofproductswillallowyoutosecurelyaccessthedatayouwant,whenandwhereyouwantit.Youwillbeableto enjoy the freedom that wireless networking delivers.

A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires.WirelessLANsareusedincreasinglyinbothhomeandofficeenvironments,andpublicareassuchasairports,coffeeshopsand universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increasedmobilityandtheabsenceofcablingandotherfixedinfrastructurehaveproventobebeneficialformanyusers.

Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards.

Undermanycircumstances,itmaybedesirableformobilenetworkdevicestolinktoaconventionalEthernetLANinordertouseservers,printersoranInternetconnectionsuppliedthroughthewiredLAN.AWirelessAccesspointisadeviceusedtoprovide this link.

Wireless Basics



What is Wireless?

Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequencytoconnectwirelessly,soyouhavethefreedomtoconnectcomputersanywhereinyourhomeoroffice. D-Linkistheworldwideleaderandawardwinningdesigner,developer,andmanufacturerofnetworkingproducts.D-Linkdelivers the performance you need at a price you can afford. D-Link has all the products you need to build your network.

How does wireless work? Wirelessworkssimilartohowcordlessphonework,throughradiosignalstotransmitdatafromonepointAtopointB.Butwirelesstechnologyhasrestrictionsastohowyoucanaccessthenetwork.Youmustbewithinthewirelessnetworkrangeareatobeabletoconnectyourcomputer.TherearetwodifferenttypesofwirelessnetworksWirelessLocalAreaNetwork(WLAN),and Wireless Personal Area Network (WPAN).

Wireless Local Area Network (WLAN)

Inawirelesslocalareanetwork,adevicecalledanAccessPoint(AP)connectscomputerstothenetwork.Theaccesspointhasasmallantennaattachedtoit,whichallowsittotransmitdatabackandforthoverradiosignals.Withanindooraccesspointasseeninthepicture,thesignalcantravelupto300feet.Withanoutdooraccesspointthesignalcanreachoutupto30milestoserveplaceslikemanufacturingplants,industriallocations,collegeandhighschoolcampuses,airports,golfcourses,andmany other outdoor venues.



Wireless Personal Area Network (WPAN)

Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away.

ComparedtoWLANthespeedandwirelessoperationrangearebothlessthanWLAN,butinreturnitdoesn’tusenearlyasmuchpowerwhichmakesitidealforpersonaldevices,suchasmobilephones,PDAs,headphones,laptops,speakers,andotherdevices that operate on batteries.

Who uses wireless? Wirelesstechnologyhasbecomesopopular inrecentyearsthatalmosteveryoneisusingit,whether it’sforhome,office,business,D-Linkhasawirelesssolutionforit.

Home •Giveseveryoneathomebroadbandaccess •Surftheweb,checkemail,instantmessage,etc. •Getsridofthecablesaroundthehouse •Simpleandeasytouse

Small Office and Home Office •Stayontopofeverythingathomeasyouwouldatoffice •Remotelyaccessyourofficenetworkfromhome •ShareInternetconnectionandprinterwithmultiplecomputers •Noneedtodedicateofficespace



Where is wireless used? Wirelesstechnologyisexpandingeverywherenotjustathomeoroffice.Peoplelikethefreedomofmobilityandit’sbecomingso popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.

UsingaD-LinkCardbusAdapterwithyourlaptop,youcanaccessthehotspottoconnecttoInternetfromremotelocationslike:Airports,Hotels,CoffeeShops,Libraries,Restaurants,andConventionCenters.

Wirelessnetworkiseasytosetup,butifyou’reinstallingitforthefirsttimeitcouldbequiteatasknotknowingwheretostart.That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.

Tips

Hereareafewthingstokeepinmind,whenyouinstallawirelessnetwork.

CentralizeyouraccesspointorAccessPoint Make sure you place the bridge/access point in a centralized location within your network for the best performance. Try to placethebridge/accesspointashighaspossibleintheroom,sothesignalgetsdispersedthroughoutyourhome.Ifyouhaveatwo-storyhome,youmayneedarepeatertoboostthesignaltoextendtherange.

Eliminate Interference Placehomeappliancessuchascordlesstelephones,microwaves,wirelessspeakers,andtelevisionsasfarawayaspossiblefromthe bridge/access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency.



Security Don’tletyournext-doorneighborsorintrudersconnecttoyourwirelessnetwork.Secureyourwirelessnetworkbyturningon the WPA or WEP security feature on the access point. Refer to product manual for detail information on how to set it up.

There are basically two modes of networking:

•Infrastructure–All wireless clients will connect to an access point or wireless bridge.

•Ad-Hoc–Directlyconnectingtoanothercomputer,forpeer-to-peercommunication,usingwirelessnetworkadaptersoneachcomputer,suchastwoormorewirelessnetworkCardbusadapters.

AnInfrastructurenetworkcontainsanAccessPointorwirelessbridge.Allthewirelessdevices,orclients,willconnecttothewireless bridge or access point.

AnAd-Hocnetworkcontainsonlyclients,suchaslaptopswithwirelesscardbusadapters.AlltheadaptersmustbeinAd-Hocmode to communicate.

Wireless Modes


Appendix B - Networking Basics

Networking BasicsCheck your IP addressAfteryouinstallyouradapter,bydefault,theTCP/IPsettingsshouldbesettoobtainanIPaddressfromaDHCPserver(i.e.wirelessrouter)automatically.ToverifyyourIPaddress,pleasefollowthestepsbelow.

ClickonStart>Run.Intherunboxtypecmd and click OK. (Windows® 7/Vista® userstypecmdintheStartSearchbox.)

Attheprompt,typeipconfig and press Enter.

ThiswilldisplaytheIPaddress,subnetmask,andthedefault gateway of your adapter.

Iftheaddressis0.0.0.0,checkyouradapterinstallation,security settings, and the settingsonyour router.Some firewall software programs may block a DHCP request on newly installed adapters.


Appendix B - Networking Basics

Statically Assign an IP addressIfyouarenotusingaDHCPcapablegateway/router,oryouneedtoassignastaticIPaddress,pleasefollowthestepsbelow:

Step 1Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Change Adapter

Setting. Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network

Connections.Windows® XP - Click on Start > Control Panel > Network Connections.Windows®2000- Fromthedesktop,right-clickMy Network Places > Properties.

Step 2Right-click on the Local Area Connection which represents your network adapter and select Properties.

Step 3Highlight Internet Protocol (TCP/IP) and click Properties.

Step 4Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router.

Example:Iftherouter´sLANIPaddressis192.168.0.1,makeyourIPaddress192.168.0.Xwhere X is a number between 2 and 99. Make sure that the number you choose is not in useonthenetwork.SetDefaultGatewaythesameastheLANIPaddressofyourrouter(192.168.0.1).

Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP.

Step 5Click OK twice to save your settings.


Appendix C - Technical Specifications

Technical SpecificationsStandards •IEEE802.11n •IEEE802.11g •IEEE802.11b •IEEE802.3 •IEEE802.3u

Security •WPA-Personal •WPA2-Personal •WPA-Enterprise •WPA2-Enterprise Wireless Signal Rates1

•300Mbps •108Mbps •54Mbps •48Mbps •36Mbps •24Mbps •18Mbps •12Mbps •11Mbps •9Mbps •6Mbps •5.5Mbps •2Mbps •1Mbps

Maximum Operating Voltage •5V1A

Maximum Operating Current •450mA

Modulation •DQPSK •DBPSK •CCK •OFDM

Frequency Range2

•2.4GHzto2.483GHz

LEDs •Power •Wireless •Security •LAN

Operating Temperature •32°Fto131°F(0°Cto55°C)

Humidity •90%maximum(non-condensing)

Safety & Emissions •FCC •IC •CE •C-Tick

Dimensions •144(W)x109(D)x30(H)mm(5.67x4.29x1.18inches)

1MaximumwirelesssignalratederivedfromIEEEStandard802.11gand802.11nspecifications.Actualdatathroughputwillvary.Networkconditionsandenvironmentalfactors,includingvolumeofnetworktraffic,buildingmaterialsandconstruction,andnetworkoverhead,loweractualdatathroughputrate.Environmentalconditionswilladverselyaffect wireless signal range.

2Range varies depending on country’s regulation.


Trademarks:D-LinkisaregisteredtrademarkofD-LinkCorporation/D-LinkSystems,Inc.Othertrademarksorregisteredtrademarksarethepropertyoftheirrespective owners.

Copyright Statement:No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivativesuchastranslation,transformation,oradaptationwithoutpermissionfromD-LinkCorporation/D-LinkSystems,Inc.,asstipulatedbytheUnited States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.

Copyright©2010-2011byD-LinkCorporation/D-LinkSystems,Inc.Allrightsreserved.

CE Mark Warning:ThisisaClassBproduct.Inadomesticenvironment,thisproductmaycauseradiointerference,inwhichcasetheusermayberequiredtotakeadequate measures.

Federal Communication Commission Interference Statement

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyone of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consultthedealeroranexperiencedradio/TVtechnicianforhelp. FCCCaution:Anychangesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.


IMPORTANT NOTE:FCCRadiationExposureStatement:

ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwithminimumdistance20cmbetweentheradiator&yourbody.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.

Industry Canada StatementThis device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesired operation.

IMPORTANT NOTE:RadiationExposureStatement:

ThisequipmentcomplieswithICradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwithminimumdistance20cmbetweentheradiator&yourbody.Thisdevicehasbeendesignedtooperatewithanantennahavingamaximumgainof[2]dB.Antennahavingahighergainisstrictlyprohibitedper regulations of Industry Canada. The required antenna impedance is 50 ohms.

UnderIndustryCanadaregulations,thisradiotransmittermayonlyoperateusinganantennaofatypeandmaximum(orlesser)gainapprovedforthetransmitterbyIndustryCanada.Toreducepotentialradiointerferencetootherusers,theantennatypeanditsgainshouldbesochosenthatthe equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter (IC: 4216A-AP1360C1 / Model: DAP-1360C1) has been approved by Industry Canada to operate with the antenna types listed belowwiththemaximumpermissiblegainandrequiredantennaimpedanceforeachantennatypeindicated.Antennatypesnotincludedinthislist,havingagaingreaterthanthemaximumgainindicatedforthattype,arestrictlyprohibitedforusewiththisdevice.

CedispositifestconformeàlanormeCNR-210d’IndustrieCanadaapplicableauxappareilsradioexemptsdelicence.Sonfonctionnementestsujetauxdeuxconditionssuivantes:(1)ledispositifnedoitpasproduiredebrouillagepréjudiciable,et(2)cedispositifdoitacceptertoutbrouillagereçu,ycomprisunbrouillagesusceptibledeprovoquerunfonctionnementindésirable.


NOTE IMPORTANTE: Déclarationd’expositionauxradiations:

Cetéquipementestconformeauxlimitesd’expositionauxrayonnementsICétabliespourunenvironnementnoncontrôlé.Cetéquipementdoitêtreinstalléetutiliséavecunminimumde20cmdedistanceentrelasourcederayonnementetvotrecorps.

CedispositifaétéconçupourfonctionneravecuneantenneayantungainmaximaldedB[2].Uneantenneàgainplusélevéeststrictementinterditeparlesrèglementsd’IndustrieCanada.L’impédanced’antennerequiseestde50ohms.

Conformémentàlaréglementationd’IndustrieCanada,leprésentémetteurradiopeutfonctionneravecuneantenned’untypeetd’ungainmaximal(ouinférieur)approuvépourl’émetteurparIndustrieCanada.Danslebutderéduirelesrisquesdebrouillageradioélectriqueàl’intentiondesautresutilisateurs,ilfautchoisirletyped’antenneetsongaindesortequelapuissanceisotroperayonnéeéquivalente(p.i.r.e.)nedépassepasl’intensiténécessaireàl’établissementd’unecommunicationsatisfaisante.

Leprésentémetteurradio(IC:4216A-AP1360C1/Model:DAP-1360C1)aétéapprouvéparIndustrieCanadapourfonctionneraveclestypesd’antenneénumérésci-dessousetayantungainadmissiblemaximaletl’impédancerequisepourchaquetyped’antenne.Lestypesd’antennenoninclusdanscetteliste,oudontlegainestsupérieuraugainmaximalindiqué,sontstrictementinterditspourl’exploitationdel’émetteur.Antennainformation:dipole/2dBi(Brand:D-Link/Manufacturer:WHAYU)

wireless n open source access point - d-link€¦ · the d-link wireless n open source access point...

Documents