3531835447

_BLI_ Ol COI4TIII<ilT5

Safety Information ...................... 2

Important Installation Instructions ...... 2

Safety Features ......................... 2

Pre-installation Checklist ................ 3

Garage Door Opener Assembly ......... 9

Record Data (for Service) .............. 11

Garage Door Opener Installation ....... 12

Accessories ........................... 22

Maintenance .......................... 25

Troubleshooting ...................... 26

Wiring Diagram ....................... 29

Warranty information .................. 30

Wl' '14ID4 [ELLICODE,.

For 7' 6" Doors. Extension Kit is available for 8' Doors

Included Wall Control MUST be installed prior to Operationof this Garage Door Operator.

Safe-T-Beam ® Safety Reverse System Must be Installed andthe Force Controls MUST be Properly Set to dose door.

This Equipment meets or exceeds al Federal, State and UL 325Safety Requirements.

Will not operate twice as fast on a one-piece door.

_ ! _ _'_%_ _%_ _ %_ 4'__ %_

Garage Doors are heavy objects that move with the help of springsunder high tension and electric opening equipment. Since movingobjects, springs under tension, and electric opening equipmentmay cause injuries, your safety and the safety of others depend onyou reading and understanding the information in this manual.

If you have garage door related questions or do not understand theinformation presented, call your nearest Genie Factory AuthorizedDealer listed at www.geniecompanyocom, or customer Service at1-800-35-GENIE..

MOVINGDOOR

ELECTRICALSHOCK

HiGHSPRINGTENSION

EFFECT

WARNING:Can Cause Serious

Injury or Death

WARNING:Can Cause Serious

Injury or Death

WARNING:Can Cause Serious

Injury or Death

• Keep people clear of opening while door is moving.

• Do Not allow children to play with the door operator.

• Do Not operate a door that jams or one that has a broken spring.

• Turn off power before removing operator cover.

• Whep replacing cover, make sure wires are not pinched or nearmowng parts.

• Operator must be properly grounded.

• Do Not try to remove, repair or adjust springs or anythinqtowhich door sprinq parts are fastened, such as, wood blocks,steel brackets, caNes or other like items.

• Repairs and adjustments must be made by a trained serviceperson using proper tools and instructions.

WARNING:TO REDUCETHE RISKOFSEVEREINJURYOR DEATH:

1 READAND FOLLOW ALL SAFETY,INSTALLATIONANDOPERATIONINSTRUCTIONS.If you have anyquestions or do not understand an instruction, callyour service representative.

2 Do Not install operator on an improperly balanceddoor. An improperly balanced door could causesevere injury. Repairs and adjustments to cables,spring assembly, and other hardware must be madeby a trained service person using proper tools andinstructions.

3 Remove all ropes, and disable all locks connected tothe door before installing operator.

4 Install door operator 7 feet or more above the floor.Mount the emergency release knob 6 feet abovethe floor.

5 Do Not connect the operator to the source of poweruntil instructed to do so.

6 Locate the control button:• Within sightofdoor.• At a minimum height of 5 feet, so small children

cannot reach it.• Away from all moving parts of the door.

7 Install the entrapment WARNING label next to thewall button or console. Install the emergency releasetag on, or next to, the emergency release

8 The operator must reverse when the door contacts a1-1/2 inch his h object on the floor at the center ofthe doorway.This is about the size of a 2 x 4 boardlaid flat.

Safe-T-Beam® (STB)Non-ContactReversingSystem

Places an invisible beam across door opening, that reversesthe door during down travel to the fully open position ifanything passes through beam.

Safe-T-Reverse® ContactReversingSystem

Automatically stops and reverses a closing door within 2seconds of contact with an object.

Safe-T-Stop® Timed Reversed System

Automatically opens a closing door, if door does not closewithin 30 seconds.

Force Guard ® Control

Used to set the force required for opening and closingdoor. For maximum safety, set the minimum force requiredto fully open and close door.

Automatic Lighting SystemTwo light bulbs up to 60 Watts max. each, are used for saferentries and exits.The light turns on when door is activatedand automatically turns off 4.5 minutes later.

Manual Emergency Release

Allows the garage door to be opened or closed manuallyfor emergencies or maintenance.

?sI-IIe: I'ALL£1 IOH ( HEC, HL SY

This Opener includes parts and supplies needed to install in most garages andconnect to most garage doors. There are many variations of garages and garagedoors. A few additional parts and supplies may be needed to install Opener intoyour garage and connect to your garage door. While checking items listedbelow, note any additional items you will need.

• 12'+TapeMeasure • Pencil • Ladder • Level

Che<k l_ollow _s9 .......

C/tICR I}_AJ! C,oH[)I IIOH RH[)

Check condition of vertical stile in center of door, and its connection to door'stop and bottom beams.

A If door frame is nailed together and not a solid connection, door framemust be braced or reinforced before installing Opener.

B If door is"lightweight" (made with frame and skin - not so/d),door(including door frame) must be braced or reinforced beforeinstalling Opener.

C A door opener reinforcement bracket may also be needed to connectgarage door to Opener's Door Bracket. This Opener is designed forinstallation on a properly braced sectional door or solidly bracedone-piece door.

D Contact your Genie Factory Authorized Dealer or dealer of your garagedoor for any necessary bracing and a door opener reinforcementbracket (if needed) before proceeding.

E If you have a wooden door, measure door's thickness. (1/4" x 2") LagScrews are included for installing Door Bracket onto door. If your dooris less than 2"thick, brace door or use shorter Door Bracket LagScrews (1/4" x 11/4" - not included)

.& WARNING:If your door sticks, binds, or is out ofbalance, have it adjusted by a Genie FactoryAuthorized Dealer. Door springs, cables,pulleys, brackets and associated hardwareare under extreme tension and can causeserious injury or death.

NOTEThe Excelerator Opener is equipped withan automatic Garage Door BalanceDetection System.See TroubleshootingGuide on page 27.

KEEP FEET CLEAR OF DOOR

_ Sectional Door

Raise door, check alignment and see if it moves freely (Figure 1). If doorappears out of alignment, binds, or does not move smoothly, contact aGenie Factory Authorized Dealer or dealer of your garage door for repairsand adjustments to door mechanism.

Raise door to 3' - 4' above ground and carefully let go. Door should staystationary. Slight movement is acceptable. More than slight movementmeans door is out of balance. Contact a Genie Factory Authorized Dealeror dealer of your garage doorfor repairs and adjustments SECTIONALDOOR,TORSIONSPRINGS

to door mechanism. Springs

Check door type. Makea note of whether it is a

sectional or a one-piecedoor (Figure 2).

J One-Piece Door

Figure 1 Checking door balance

SECTIONAL DOOR, EXTENSION SPRINGS

Stile

ONE-PIECE DOOR, TRACKLESS

Header Area

Figure 2 Note Door Type

G_ _ raGE DOOB M_2 6 4T

Measure garage door height (7'-6", 8'-0", or taller) withtape measure.

A If door height is 7'-6" or less, continue with Check Step 4.

B If your door height is above 7'-6% make sure your rail is longenough to open the garage door. If there is any questioncontact your Customer Service Representative at1-800-35-GENIE.

Figure 3 Rail Extension Kit

Rail Extension for8' door

C4ECH DOOB _S_C}_}_ ABEA

NOTEThe header is a heavily reinforced section of the wall justabove the top of the garage door opening.

A Find vertical center line of door and header:• Close door.

• Measure door width at top.• Mark a point at center of door and on header directly

above door. Draw a center line to connect points.

Find Header Bracket mounting height (Figure 4):(Do not attach Header Bracket).

. Raise door, watching top edge of door and stop doorwhen its edge reaches its highest point.

• Measure distance ("H") from top edge of door to floor.

For sectional doors, add 2-1/2" to"H'[ Mark a pointon center line. Bottom of Header Bracket will beinstalled here.

For one-piece doors, add 6" to"W: Mark this point oncenter line. Bottom of Header Bracket will beinstalled here.

NOTEe For both types of doors:

- If the ceiling in.your garage is so low that there isnot at least a 3 space above the Header Bracketmountingpoint, contact a Genie FactoryAuthorizedDealer.

If a door spring is in the way, place the HeaderBracket avove the spring. Do Not move the door spring.

Check wall for a stud or a solid header at your mark:(If checking a finished wall, a stud finder may be helpful).

• If location is above Header, a 2" x 6" board must be

screwed to studs beside your mark with at least two LagScrews and Flat Washers (not provided).

• Transfer your mark to new mounting board.

SECTIONAL DOOR

H + 21/2

H

ONE-PIECE DOOR

H+6"

Figure 4 Find Highest Point of Travel

11/=', llI'

Check ceiling or space above where Opener Power Head will bemounted (Figure 5):

A Measure from garage door center line mark toward rearof ga rage:

. Approximately 10' back if garage has a 7' 6" door.

• Approximately ] 1' back if garage has an 8' O" door.

Approximately ] 3' back if garage has an 10' O"door.

Approximately ] 4' back if garage has an 12' O"door.

NOTEMounting Straps are included to attach the Opener to mostgarage ceilings. Garage construction varies widely.Additional mounting straps or angle iron may be needed foryour installation.

El Find location of ceiling joist or truss above where OpenerPower Head will be and estimate type and quantity ofmaterials needed for your installation (Figure 6).

120 Volt grounded outlet

or wiring box within 3 feet ofPower Head.

10'_

for 7-1/2' doors

__ ]]'__-for 8' doors

-;oo4]]L!-Figure 5 Check Power Head location

OPEN BEAM CEILING EXAMPLES

Mounting Straps Support board addedfor longer spans

PerforatedAngle Iron

_(Angle iron not included)

FINISHED CEILINGS

Locate ceiling joists ortrusses usinga stud finderor similardevice.

Attach angle iron(not included) tojoists or trussesthrough finish materialusing Lag Screws.

Figure 6 Mounting methods for open beam and finished ceilings

CHECK ..... _ "...... C[F L s_G FOB C_BOUH©E©

t>ow@:_Sou_:_cz

A Check that there is a 15 Amp 120 Volt grounded electricaloutlet or grounded permanent wiring box (per building code)within 3' of Opener Power Head:

If not, an outlet or wiring box must be installed. Contacta licensed electrician for installation.

If building codes require permanent wiring, Power Headmust be partially disassembled to install appropriatewiring in place of Power Cord. See page 19

NOTEPermanent wiring must be installed by a LicensedElectrician. Not all Genie Factory Authorized Dealers areLicensed Electricians. Contact someone who is a LicensedElectrician.

g%_ i,/s i,i i ii_ ,;

Check for wood garage frame, jamb, or masonry at mounting location(6" above floor) with attachment tabs facing away from garage door(Figure 7).

A If you cannot mount Safe-T-Beam @Mounting Bracket towood frame:

. Concrete screws and concrete anchors (not included)must be used to mount Brackets on masonry withattachment tabs facing away from garage door.

. Safe-T-Beam @Mounting Bracket Extensions may be used(not included - available from a Genie Factory AuthorizedDealer or through Accessories Order Form on pages 31/32).

_ _60_5 M I]IUb Eb TOOLS

AB

Tools (Figure 8):Additional tools to make installation easier:

• Slotted and phillips screw-driver bits

• Stud finder

• Sheet-metal cutting snips

Source ISensor

Safe T Beam @ ,i,l,,ll/ll_Mounting Bracket

; // I _" Bracket 6"#,_ I above

_ 41_r7 I floor

Figure 7 Mounting Safe-T-Beam @Components

IillT;40vE EXI_;_ll_G 6ABA_[I£

Check that the garage door locks, rope, and T-Handles are removedfrom the garage door before starting the installation.

A If your garage does not have a separate entry door, it is highlyrecommended to install a Genie Emergency Release Kit (GER-2).Emergency Release Kit lets you open garage door from outside ifthere is a power failure. (Please see Accessories Order Form onpages 31/32.)

Befo_,4_-9o __9f_x_t_"_e_,9<_t a_,_yterns a_,'_dtoo

_,s®®d®do 7'os_

[] Safe-T-Beam @Sensor Mounting Bracket Extensions (dealer)

[] Garage door opener reinforcement bracket (dealer)

[] Garage door frame reinforcement brackets, screws, bracingor reinforcement kits (dealer)

[] Lag Screws (11/4") for a wood door less than 2" thick (store)

[] Electrical outlet and/or wiring (supplied by alicensed electrician)

[] Excelerator Extension Kit (for 8' garage doors) (store)

[] Sufficient angle iron or strapping for hanging Power Head(store)

[] Two 60Watt light bulbs(Rough service bulbs recommended)(store)

[] GER-2 Emergency Release Kit for entry during power failure(store)

[] Wood for header, ceiling, and/or door bracing reinforcement(if needed)

[] Masonry fasteners for Safe-T-Beam @Bracket installation,(if needed)

[] Masonry drill bit (if needed)

Drill

1/16" 5/32"

Drill Bit Drill Bit

6' or 7'Step Ladde_

Adjustable Wrench

Phillips Screwdriver

Hack Saw

12' *

Tape

Hammer

WireStripper

Safety Glasses

(1i¢ ">

Pencil

8888881/4" 5/16" 3/8" 7/16" 1/2" 9/16"

Sockets

Carpenter's Level

Figure 8 Recommended Tools

item Part Name QuantityRequired

1 Power Head Assembly (main carton) 1 1

2 1/#L20 X 13/16" Hex Head Shoulder Bolt (blue bag) 2 2(yellow bolt)

3 RailAssembly (1 piece)(packagedseparately) 1

4 RailAssembly (3 piece)(main carton) 1

4A First RailSection 1

4B Middle RailSection 1

4C End RailSection 1

8 1/#'-20 Hex Serrated FlangeNut (blue bag) 4 4

g RailClamps(blue bag) 4

10 5/16"-18 x 11/16t_Hex HeadShoulder Bolt (blue bag) 8

11 5/16"-18 Hex Serrated FlangeNut (blue & orange bags) varieS/mode 12

12 Magnetic Carriage Assembly (main carton) 1 1

13 Collar (blue bag) 3

14 Retaining Clip (blue bag) 3

15 RailStrap(blue bag) 1 1

16 1/4'L20 Hex HeadBolt (blue bag) 2 2

18 Open Limit Switch Assembly (Wbite)(green bag) 1 1

19 CloseLimit Switch Assembly (Brown) (green bag) 1 1

21 No.8-32 x 1" Hex HeadScrew(green bag) 2 2

22 Emergency ReleaseCord (green bag) 1 1

23 EmergencyReleaseCord (Iong)(yellow) ld&lZon[y

24 Emergency ReleaseKnob (green bag) 1 1

25 Emergency ReleaseTag(green bag) 1 1

26 Header Bracket(orange bag) 1 1

28 Door Bracket(orange bag) 1 1

30 1/#' x 2" Lag Screw(orange bag) varieS/modeI 8

31 Straight Door Arm (main carton) 1 1

32 ClevisPin,3/8" x 15/16" (yellow bag) 2 2

33 Cotter Pin,.073_'dia.(yellow bag) 2 2

34 Curved Door Arm (main carton) 1 1

35 3/8_'x 7/8" Hex Head Bolt (yellow bag) 2 2

36 3/8_'Hex Serrated Flange Nut (yellow bag) 2 2

37_ 2-Conductor Wire (main carton) 1 Roll 1 Roll

38_ Insulated Staple (red bag) approx.30 approx.30

40< Wall Console (main carton) 1 1

4Y #6 x 1-1/4" PanHead Screw (red bag) 2 2

42_ Entrapment Warning Label (manual)(main carton) 1 1

43_ Safe-T-Beam(STB)Sensor (GreenLED)(maincarton) 1 1

44_ Safe-T-Beam(STB)Source (Red LED)(maincarton) 1 1

45_ Safe-T-Beam(STB)Bracket (yellow bag) 2 2

46 Coupler (blue bag) 1 1

47_ NoJ 0 xl 1/4" Phillips HexHeadScrew(yellow bag) 4 4

48_ 1 Button Remote Control (main carton) /aAeS/mode

49_ 3 Button Remote Control (main carton) /arieS/mode

5@ Wireless Keypad(main carton) varieS/modeI aries/mode

51x 2 Button Remote Control (main carton) varieS/modeI /aries/mode

52_ Safety & Maintenance Guide (manua!(main carton) 1 1

53 WireClip (green bag) 7

54 Bumper (blue bag) 1 1

55x 5/16'L18x 3/4" HexHeadBolt (orange bag) 3

56 1/4-20 x 3/4" Self-drilling Screw(orange bag) 3 3

57 Mounting Straps(main carton) 2 2

' Denotesitemsnot shownon page8. Theseitemswill be illustratedthroughout the manualasrequired.

J4:_,,:_IW}BLJEXP_,.O©I}© Vll!r<

[11

(__ Model Number

item

1A

1B

1C

1D

1E

1G

1H

1K

1L

1M

1P

Part Name

Lens

Top Plate Assembly

Light Socket (2)

Motor AssemblyCover

Motor Drive Board

Controller Board

No. 10-24 x 3/8" Hex Head

No.8-32 x r' Phillips ScrewNo.8-32 x 3/8"Slotted Hex Head Screw

Power Cord

F:o_"Help _:sll ]-g00-35 61:11_411o viii wwwge_ai_r(ompal{y _.om 7

NOTEOpener will not function unless Safe-T-Beam® System is installed and Force Controls are properly set.

One-Piece Rail Assembly (Genie Pro only) for 10' or 12' door includes:• Special"Close"Limit Switch with IongerWires.• 96" Emergency Release Cord (yellow).• Rail Support Kit.

Rail Assembly (1 piece)

zz

@

A Turn Power Head upside down and place on a flatlevel surface.

B Install Bumper (Figure 9).

C Install Coupler on Motor Shaft (Figure 9).

CAUTIONThe Drive Screw and Rail Liner can slide out of Rail Sections.Keep Rail Sections level until the Opener is fully assembled.

D Connect first Rail Section to Opener Power Head. Connectwith 2 (1/4"-20) (yellow) Hex Head Shoulder Bolts and2 (1/4"-20) Hex Serrated Flange Nuts (Figure 10).Finger-tighten until later.

If you have a 1-piece rail unit, skip Assembly Step 2.

A Arrange arrows on Rail Sections to point in same directionand away from Power Head:• Push Middle Drive Screw out about 2" toward Power Head.

• Slide Collar over Middle Drive Screw Hook (Figure 11A).Turn Middle Screw by hand to align Drive Screw Hooksbetween First and Middle Rail Sections.

. Latch two Hooks together and slide Collar over them(Figure 11 B) and (Figure 11 C).

• Snap Clip on Drive Screw next to Collar (Figure11D).

B Attach Middle Rail Section to First Rail Section, using 2 RailClamps,4 (5/16"-18) Hex Shoulder Bolts, and 4 (5/16"-18) HexHead Serrated Flange Nuts onto Bolts (Figure 11).Finger-tighten until later. (Middle Rail Section looks thesame on both ends. See page 8.)

C Attach End Rail Section to Middle Rail Section followingprocedures in step A & B.

RailStrap

RailClamps

©Coupler

First RailSection

5/16"-18HexHeadShoulderBolts

@)_Q_Q_88_

5/16"-18HexSerratedFlangeNuts

88

1/4"-20Hex 1/4"-20HexHead 1/4"-20HexSerratedFlangeNuts ShoulderBolts HeadBolts

(yellow)

Bumper Collars+ spare RetainingClips + spare

Hardware (blue bag)

Bumper(remove backing)

e%-"i

Coupler Power HeadAssembly

(i)

Figure 9 Install Bumper, Coupler and 1st Rail Section

Figure 10 Bolt ] st Rail Section to Power Head

NOTE

If the Extension Assembly (GSXL8) is needed, attachit per instructions supplied with kit,

Retaining_"-.

\_ \\ \

Middle Rail ", _ Collar

Section @ f-.

Arrowspointtowarddoor

@ RailClamps

11A. Slipon collar

11B. EngageHooks

11C._Slide CollaroverHooks

11D._Snap on RetainingClip

Figure 11 Attach Middle Rail Section

_;:o__H_g:; _:s 1 800 3_.6_:B t: o vet 9

A

B

_S EMBtY Oh_TO _;_. tS

Place Magnetic Carriage Assembly Lever in "release" position.

Slide Magnetic Carriage Assembly into slot on End RailSection with arrow pointing away from the Power Head(Figure 12).

Magnetic Carriage Release

Toward door

and header

Toward Power Head End Rail Section

©Figure 12 Slide Magnetic Carriage onto Rail

A:T'T CH I:IAIL <->s TO I;I_ _'s

I:IAIL < =......o>I_,. I ION

A Attach Rail Strap to End Rail Section with 2 (1/4"-20) HexHead Bolts and 2 (1/4"-20) Serrated Flange Hex Nuts(Figure 13).

B Tighten snugly but Do Not over-tighten.

Rail Strap@ _ (_1_

I_ I < I''° p, Ii+ <"14LI °H I:I?AIL,2,E,,.I l;J ,=,=,I_HIi)

TI(IIITEH =LL _OLYS

A Align all Rail Sections so Magnetic Carriage Assembly canslide freely along length of Rail.

B Securely tighten all fasteners now. Do Not over-tighten.

IIIST ILL IIIU© COb, IF,!ECT LB/ilT

o>@I I,.HEo=

i!iiii! IiilBiI!i!iiI!i!iiI!i!iiI!i!iiI!i!iA

B

C

D

Turn Opener right side up and support Power Head to avoiddamaging the Light Bulb Sockets.

Uncoil Limit Switch Wires and retain Twist Ties.

Place Switches on Rail with arrows pointing away fromPower Head (Figure 14).

Place Close Limit Switch (Brown Wire) 15" from Rail Strap.Insert (#8-32 x 1") Hex Head Screw into Switch hole and

finger-tighten until later.

Place Open Limit Switch (White Wire) 15" from Power Head.Insert (#8-32 x 1") Hex Head Screw into Switch hole and

finger-tighten until later.

Figure 13 Attach Rail Strap

WhiteWire

Wire

#8-32Hex Head Screws Wire Clips

Close Limit Emergency EmergencySwitch Assembly Release Knob Release Tag

Hardware (green bag)

Close LimitSwitch

(Brown wire)

Open LimitSwitch _--

(White wire)

@Wire

Clip@

,_rrows point

:rdd #8-32 x 1 //_Hex Head_-_

Screws _lp

Figure 14 Install Limit Switches on Assembled Rail

NOTE

Loosen (Do Not Remove) Terminal Block Screws°Limit Switch adjustments and securing the Wireswill be done later.

F Lay Wires in channel on top of Rail and secure with Wire Clips(Figure 14).

G Coil and bundle excess Limit Switch Wires on top of PowerHead with Twist Ties. Leave just enough Wire to reachTerminals on back of Power Head (Figure 14).

14 Turn Opener upside down, and connect Limit Switch Wires toPower Head Terminal Block (Figure 15):* Terminal 4: OPEN Limit Switch Wire (white).. Terminal 5: OPEN Limit Switch Wire (white) and

CLOSE Limit Switch Wire (brown).. Terminal 6: CLOSE Limit Switch Wire (brown).

Antenna

J

/

Terminal White Limit Brown LimitBlock Switch wires Switch wires

Figure 15 Connect Limit Switch Wires to PowerHead Terminal Block

_'_ %1C: 11"2 // . '/"

l<&l<l =_ !I W

A Tie overhand knot at one end of Emergency Release Cord.

B Thread opposite end of Cord through Knob and hole inMagnetic Carriage Assembly Release Lever (Figure 16).

C Tie overhand knot at this end of Emergency Release Cord.

D Attach Emergency ReleaseTag to Magnetic CarriageAssembly Release Lever.

I:II!COBD I% _i:_, :> _ # '+_#I_:: ,_El @OIsl!L

Al*'_![)S£BIAL l%h =_:+_'_>I I 1,)_IY111, Z: II

Please note the following information so it is available if you needto call us:

Date purchased: / /

Serial number (Figure 17):

Model number (Figure 17):

Dealer Name:

Dealer Address:

City:

State:

Zip:

Phone:

Emergency

'_--_ Release Knob®Figure 16 Attach Emergency ReleaseCord/Knob

and Tag

ModelNumber

NOTE

Please keep original or photocopy of your sales receipt withthis manual for future reference should service ever berequired.

SerialNumber

(example)WK YR PI

01 02 4E

Figure 17 Model and Serial Numbers

6ARA6E: DOOR ORHER _HS_kLAdT OH

NOTE

For lightweight garage doors, make sure you have installedthe proper reinforcement (SeeCheck Door Condition andThickness on page 3).

CAUTION• The Header Bracket must be fastened to the garage

framing. Do Not fasten the Header Bracket to drywall,particle board, plaster, or other such material.

• It may be necessary to attach a 2" x 6" board across thewall studs above the door header to serve as amounting plate for the Header Bracket. The Bracket canthen be mounted at the proper location and havesufficient support.

• If a door spring is in the way, place the Header Bracketabove the spring. Do Not move the door spring.

Mount directlyinto header

Use of Header Bracketsupport board

Alternative Header Bracket orientations

Highest Point of door travel _+ 2-1/2" (sectional door) or

+ 6" (one-piece door)

Figure 18 Attach Header Bracket above Garage Door

A If needed, attach a 2" x 6" board (Figure 18) (also see page 4)with at least two (four is recommended) Lag Screws and FlatWashers (not supplied).

B Attach Header Bracket to header at mark above door.

NOTE

Mounting variations are shown in Figure 18. Any of thesemay be used depending on space. However, it is critical thatthe point where the Rail attaches to the Header Bracket beon the center line of the door.

• Mark 3 hole positions.• Drill 3 (5/32") pilot holes.. Attach Header Bracket with 3 (1/4" x 2") Lag Screws.

HeaderBracket

®???5/16-18 x 3/4"Hex Head Bolts

1/4" x 2"Lag Screws

Door Bracket

@®@®®5/16-18 x 3/4"

Hex Serrated Flange Nuts

@7I??1/4"-20 x 3/4"

Self-Drilling Screws

Hardware (orange bag)

CAUTIONDoors made of masonite, lightweight wood, fiberglass, metal,or other lightweight materials must be properly bracedbefore mounting door Opener.

_o s; c o_Idoos

A

B

Place Door Bracket on door center line, no lower than toproller, and mark holes (Figure 19).

Attach Door Bracket:

For metal doors, use 3 (1/4"-2O x 3/4") Self-DrtlingScrews (provided).

. For wood doors, use 3 (1/4" x 2") Lag Screws or3 (1/4" x 11/4") Lag Screws (not provided).

or@--_ @

SECTIONAL DOORSLine of door

ONE-PIECE DOORS

Optional Door Operator Bracket (not included)

Figure 19 Attach Door Bracket

NOTE

Before installing, check length of the included Lag Screws vs.the thickness of your garage door. For doors thinner than 2,use 11/4 Lag Screws. Check door condition and thickness.See page 3.

Fo o_-_e-piec_;>doo s::A Position Door Bracket on door's center line, as high as

possible or on top of door.

B Attach Door Bracket:

. Formetaldoors, use3(1/4"-2Ox3/4")Self-DrtlingScrews.

For wood doors, use 3 (1/4" x 2") Lag Screws.

SS]I'TtIC/4 I;IAIL 0 MEIsIi)EI

A While supporting the Power Head, place threaded end of RailStrap Bolt through Header Bracket hole (Figure 20).

B Attach (5/16"-18) Flange Nut to Rail Strap Bolt.Finger-tighten until later.

Rail Strap Bolt

Rail (_)

Header Bracket

Figure 20 Attach Rail Strap to Header Bracket

A RaiseandsupportOpener Power Head (along door centerline) higher than highest point of door travel (using stepladder, etc.) (Figure 21).

B Measure distance from Opener to garage ceiling.

CAUTIONMounting Brackets must be fastened to garage framing.Do Not fasten to drywall, particle board, plaster, or othersuch materials.

NOTE

• Make sure the rail of your supported Power Head isslightly higher than the highest point of door travelby raisingthe door to check. Adjust as needed.

• Materials needed for mounting Opener Power Headto garage may vary. Read all instructions completely.

• Garage constructions differ. Extra material may beneeded. SeeCheckPower HeadMounting Areaonpage S.

SECTIONAL DOORS

Rail Should be level or dip down slightly.Check for clearance.

C Install Mounting Straps and/or support brackets (angle ironnot included) to joists or trusses and to mounting slots inOpener. Use (5/16"-18 x 3/4") Hex Head Bolt, (5/16"-18)Serrated Flanged Nut, and (1/4" x 2") Lag Screws as needed(Figure 22).

D Securely tighten all fasteners now. Do Not over-tighten.

ONE-PIECE DOORS

Set clearance at 1"-11/2"between Rail and door at

highest point of travel.

Figure 21 Checking Power Head position

OPEN BEAM CEILING EXAMPLES

Mounting Straps Support board addedfor longer spans

PerforatedAngle Iron

(Angle iron not included)

FINISHED CEILINGSLocate ceiling joists ortrusses usinga stud finderor similardevice.

Attach angle iron(not included) tojoists or trussesthrough finish materialusing Lag Screws.

Figure 22 Mounting methods for open beam and finished ceilings

DOOBAB_4S

A Attach Curved Door Arm to Door Bracket with Clevis Pin and

Cotter Pin (Figure 23).

B Attach Straight Door Arm to Magnetic Carriage Assembly.

C Attach both Arms together with 2 (3/8" x 7/8") Hex HeadBolts and 2 (3/8") Serrated Flange Hex Serial Number

Nuts so overall length is as short as pos-sible. Securely tighten fasteners.

D Adjust height of Emergency Release Cord Knob to 6' abovefloor:

. Pull Cord through Magnetic Carriage Assembly Leveruntil Knob is 6' from floor.

• Tie a new overhand knot in Cord at Magnetic CarriageAssembly Lever.

A Attach Straight Arm to Door Bracket with Clevis Pin andCotter Pin (Figure 24).

B Attach Curved Arm to Magnetic Carriage Assembly.

C Attach both Arms together with 2 (3/8" x 7/8") Hex HeadBolts and 2 (3/8") Serrated Flange Hex Nuts so overall lengthis as long as possible. Securely tighten fasteners.

D Adjust height of Emergency Release Cord Knob to 6' abovefloor:

. Pull Cord through Magnetic Carriage Assembly Leveruntil Knob is 6' from floor.

* Tie a new overhand knot in Cord at Magnetic CarriageAssembly Lever.

WARNINGDo Not skip Step D above!Failure to comply may leave Emergency Release Knob withinreach of children. If the Knob is pulled with garage door fullyor partially open, garage door may close without warning!

A IClevis Pins Cotter Pins

Safe-T-Beam ® (STB) Brackets

#10-16 x 11/4"Phillips Hex Head Screw

3/8" x 7/8"Hex Head Bolts

3/8" Hex SerratedFlange Nuts

Hardware (yellow bag)

As short as_ossible

ht

-Curved(_ Door Arm

Figure 23 Assemble Arms (SECTIONAL)

As long aspossible

Arm

Figure 24 Assemble Arms (ONE-PIECE)

ELECTRICAL WARNINGEnsure there is No power to the Opener before installingSafe-T-Beam® System Wires. If Opener is plugged into outlet,Unplug it now.

NOTE

The Opener will not close the door automatically unless theSafe-T-Beam® System is installed.

A Install Safe-T-Beam @Source and Sensor (Figure 25):, Mark both sides of garage door frame or wall 6"

above floor.

Hold Bracket against door frame or wall.Check if Bracketextends out from wall far enough so tongue of Bracket isbeyond door, tracks, or any door hardware. If not, Safe-T-Beam @Mounting Bracket Extensions are available from aGenie Factory Authorized Dealer or through theAccessories Order Form.

Blocks of wood, etc. may be substitutedfor extensions.

• Position top of Mounting Bracket at 6" mark and fastenwith 2 (#10-16 x 1-1/4") Phillips Hex Head Screwsper Bracket.

NOTE

Mounting Brackets can be attached to brick walls or concretefloor using masonry anchors (not included).

B Attach Safe-T-Beam @Source (Red LED) and Sensor (Green

LED) to Brackets (Figure 25):

• For single-door garages.Determine which side of garage receives the mostdirect sunlight, and place Source (Red LED) on thisside whenever possible.

, For multiple-door garages see (Figure 26).Preventing crossed signals is critical.Place Source and Sensor modules on adjacent doorsfacing in opposite directions.

NOTE

To help prevent interference from the sun, the Safe-T-Beam®Sensor (Green LED) may be placed further away from thedoor opening, where it will spend more time in the shadows.

• Slide the Safe-T-Beam @Source and Sensor onto the

tongues of the Brackets until they click into place.• Check final height of Lens (Figure 27).

Safe-T-Beam @Sensor(Green LED)

®

Safe-T-Beam @Source(Red LED)

Slide onto ,/_-___tongue ofBracket until/_;._ /it clicks into _k_2)_' "'__

)' ,/ J _,, Bracket6"place 7T J@ _ [ T°p°f4 J I above

I f,oor

Figure 25 Install Safe-T-Beams @

GARAGETWO DOORGARAGE

THREE DOORGARAGE

Figure 26 Source/sensor Locations

_k

_i L _ "_i _ ,

Figure 27 Final Check Safe-T-Beams @

Top edge of Lens5"- 6" above floor

CAUTION_tapleswhich are too tight may cut or pinch Wires. Cut or)inched Wires can cause the Safe-T-Beam® System to stopvorking. When installing the Insulated Staples, make sure_oufasten them only as tightly as needed to hold the

Wire securely.

1 1C Install Safe-T-Beam ®Wiring (Figure 28):

. Route Wire and Insulated Staples(Figure 29 and Figure 30).

Securely fasten Wires with Insulated Staples asyou go. Staples should be snug only.Wires between garage wall and Power Head shouldbe run on top of Rail and underneath Wire Clips.

Attach Wires to Safe-T-Beam ®Sensors.

Split and strip Wire ends to be connected as shown.Loosen Terminal Screws.

Insert each Wire under flat plate and tighten Screw.It does not matter which Wire, white or striped, goeson which Terminal.

Attach Wires at Power Head.Wires are connected toTerminals #2 and #3 onPower Head Terminal Block. it does not matter which

Wire, white or striped, goes on which Terminal.

Check the following.Ensure that no part of door or its hardware is in pathbetween Source or Sensor Lenses.

Ensure that tops of Lenses are between 5" - 6" abovefloor. Brackets are flexible and can be adjusted slightlyif needed.

®Insulated Staples

(approximately 30 parts)

Wi re

@

©#6-11/4"

Pan Head Screws

Hardware (red bag)

Papprox.

1/2

Figure 28 Wire the Safe-T-Beam ® System

Wire Clips @InsulatedStaples

NOTE®The Safe-T-Beam alignment check will be performed

following connection to electrical power.Do Not plug in yet!

at Safe-T-Beam ® Leave slack foradjustment

Terminalattachments

at Power Head

Figure 29 Wiring Method A

Wire Clips (_InsulatedStaples

®

Terminalattachments

at Power Head

Figure 30 Wiring Method A

Leave slack foradjustment

WARNINGVerify there is no power to the Opener before installing WallConsole Wires.

NOTE

More than one lighted Wall Control per Opener will causea malfunction.

A Wall Console (Figure :31):Has a Security Vacation Lock Switch which disablesall controls.

LED Indicator shows whether system is powered, locked,or unlocked. Makes Console easy to find in dark.Controls door Opener from inside garage.Independent Light Control allows convenient manualcontrol of Opener Lighting System.

B Find a convenient mounting location:

Within direct sight of garage door.At least 5' above floor (to prevent small children from

operating garage door).Away from any moving garage door or Opener parts (youshould not be able to reach door while standing atWall Console).

C Ensure Vacation Lock Switch is in UNLOCKED position.

D Wire Wall Console to Opener (Figure :32):

On Power Head, connect Striped Wire to Terminal #1 andWhite Wire to Terminal #2.

On back of Wall Console, connect Striped Wire toterminal "B" and White Wire to Terminal "W'[

E Attach Wall Console onto wall at location found above with 2

(#6 x ] 1/4") Pan Head Screws.

F Remove protective backing from Entrapment Warning Label,and attach it to wall near Wall Console.

CAUTIONo Use of any wall consoles other than the type included

will prevent the light from working properly and couldcause the door to operate on its own.

Cut or pinched Wires can cause the Wall Console to stopworking. When using the Insulated Staples, be sure toonly tap them in as far as needed to hold theWire snugly.

SecurityVacationLock Switch

IndependentLight Control

]

©Wall Console

@Figure :31 Wall Console

®®®

TerminalAttachment

at Power Head

White Wireto

Terminal 2

Stri ped Wireto

Terminal 1

TerminalAttachment

at Wall Console

White Wireto

Terminal "W"

Stri ped Wireto

Terminal'B"

®

_qarage Door/" Control

Allowslack

Figure 32 Install Wall Console withEntrapment Warning Label

ELECTRICALWARNINGe

A

To reduce the risk of electrical shock, this equipment hasa grounding type Plug that has a third (grounding) Pin.This Plug will only fitinto a grounding type outlet. If thePlug does not fit into the outlet, contact a qualifiedelectrician to install the proper outlet. Do Not changethe Plug in any way.The door Opener must be properlygrounded to prevent personal injury and damage to thecomponents.

The electrical power to the door Opener Must Be removedwhen the Motor Cover is removed. Electrical power mustremain off while making electrical connections.

Check building codes:

If building code requires Opener be permanently wiredto building, have a licensed electrician perform step B.If you are not installing permanent wiring, go to step C.

Instructions for licensed electrician - connecting powerwith permanent wiring (Figure 33):

• Remove power from circuit.• Remove Motor Cover.• Remove and discard Power Cord.

- Cut off Power Cord inside Power Head as near Strain

Relief as possible.- Remove Knock-Out Plug, Strain Relief, and Power

Cord. (Cut Ground Wire on line side of Toroid).- Dispose of Plug, Strain Relief, and Power Cord.

. Install required entrance bushing.

. Connect permanent wiring to Power Head Wires.- White supply line to Opener White Wire.- Black supply line to Opener Black Wire.- Ground to Opener Green Wire.- Replace Motor Cover.

NOTE

Use only Underwriters Laboratories, Inc. (U.L.)recognized wire nuts.

The Circuit Boards are light sensitive. Ensure theMotor Cover is installed before energizingthe Opener.

KnockoutCutWireshere

Two

tabsslide

Figure 33 Connecting power with permanent wiring

D

- Restore Power to circuit.

Connecting Power with Plug:

. Plug Opener into a grounded outlet as stated in previouselectrical warning.

Perform Safe-T-Beam ®alignment check:

. Check if Safe-T-Beam ®Source Red LED is glowingcontinuously (OK) or blinking (problem).

• If Red LED is blinking twice, adjust Sensor Brackets asneeded to make Red LED glow continuously. (Refer topage 26.)

SIKL£II[ _" "'¢ < s_,,_'_

$,*W 11+= "1 _>B,.f COITI( LS

Se, n_ofLm $_t(hes

A Setting Close Limit Switch (Figure 34):

• Check that Magnetic Carriage Assembly is disengaged.

, With garage door fully closed, slide Close Limit Switchuntil it is aligned with Carriage Assembly Magnet.

• Tighten Set Screw. Do Not over-tighten.

B Setting Open Limit Switch:

, Manually open garage door to full open position.

• Slide Open Limit Switch until it is aligned with CarriageAssembly Magnet.

= Tighten Set Screw. Do not over-tighten.

• Re-engage Magnetic Carriage Assembly.

NOTE

• Little effort is required to turn the ForceAdjusting Knobs.

• If the door stops moving while opening orclosing, adjust the Open Force or Close ForceControls slightly clockwise (to sightlyincrease the force) and retry the step.

• The Open Force and Close Force Controls are tobe set to the minimum force necessary toensure the door smoothly opens fully andcloses completely.

• The garage door will move slowly the firsttime it runs, until the Opener'leams"thetype of door.

• Ensure the Magnetic Carriage Assembly isengaged and is between the two LimitSwitches before operating the Opener.

WARNINGThe garage door opens rapidly, and can cause seriousinjury or death.

Keep the path cleanPosition the ladder to the side of the Power Head so it isclear of all moving parts of the Opener and the door.

Set the door Opener to use the minimum force neededto open the door.

A Pre-set Force Controls to midpoint between fully counterclockwise and fully clockwise (Figure 35).

B Adjust the Close Limit Switch:

, Press Wall Console to close garage door.If door does not close completely, measure distancefrom bottom of door to floor. Move Limit Switch

same amount toward door and try again.If door reverses after contacting floor, move LimitSwitch toward Power Head and try again.If door reverses before contacting floor, increaseClose force and try again.If door fails to move, check Safe-T-Beam ® System. SeeSafe-T-Beam ®Troubleshooting Guide on pg. 26, andOpener System Self-diagnostic Troubleshootingon pg.27.

• Tighten Limit Switch Set Screw. Do not over-tighten(strip) Limit Switch Set Screw.

C Adjust Open Limit Switch:

, Press Wall Console to open garage door.If door does not open completely, move Limit Switchtoward Power Head.

If door opens completely, but motor continues torun, move Limit Switch toward door.

. Tighten Limit Switch Set Screw. Do not over-tighten(strip) Limit Switch Set Screw.

Close Limit Switch(door fully closed)

L: o,o_

Carriage _,_ Switch

(disengaged) _%_ Magnet

Open Limit Switch Switch

Carriage(disengaged) I_ \_ .. "_

_ _) " Mag net

Figure 34 Setting Limit Switches

Force Controls

/

HI LO 0

OPEN CLOSEFORCE FORCE

Figure 35 Making Force Adjustments

NOTEe To protect your new investment, your Excelerator ® is

equipped with a Timer and Cycle Counter which worktogether to prevent any chance of heat damage toelectrical circuits caused by too many cycles in too shorta time. If your Opener suddenly stops responding to theWall Console - Do Not Unplug the Unit - simply wait10 minutes for the Timer/Cycle Counter to reset itselfand try again.

Unplugging the unit will prevent theTimer/CycleCounter from resetting.

D Test Door Opener:

• Run door up and down a few times using Wall Consoleand observe door travel.

. Repeat steps above as needed to set LimitSwitch positions.

E Adjust Open Force to minimum needed:

. Place door in closed position using Wall Console.

. Gently adjust Open Force fully counterclockwise(minimum force).

. Run Opener using Wall Console.

. Observe that door runs to Open Limit Switch.- If not, adjust Open Force Control slightly clockwise,

close garage door, and open it again.

• Repeat steps above until garage door runs smoothlyfrom Close Limit Switch to Open Limit Switch.

F Adjust Close Force to minimum needed:

• Place door in open position using Wall Console.

. Gently adjust Close Force fully counterclockwise(minimum force).

• Run Opener using Wall Console.• Observe that door runs to Close Limit Switch.

- If not, adjust Close Force Control slightly clockwise,open garage door, and close it again.

• Repeat steps above until garage door runs smoothlyfrom Open Limit Switch to Close Limit Switch.

NOTE

Limit Switch and Force Adjustments must be completedbefore checking the contact reverse function (Figure 36).

A Open garage door using Wall Console.

B Lay a 2" x 4" board flat in center of doorway.

C Close door using Wall Console.

D Check that door stops and reverses within 2 seconds after itcontacts board:

If door does not reverse, decrease Close Force untildoor reverses.

If door still does not reverse, move Limit Switchtoward door.

E Check Safe-T-Beam ® System operation:

If beam is blocked, door will not close.

NOTEThe door must contact the 2" x 4" board before theCarriage activates the Close Limit Switch. If not,readjust the Close Limit Switch.

2" x 4" boardlaid flat

Figure 36 Checking Contact Reverse

t+}F/0 6 _:/f%_tilP?}H6 T4_

_:_I_/_OT_

A To program one Button of a Remote Control (Figure 37):

• Locate Learn Button and Learn Indicator Light nearTerminal Block on Power Head (Figure :38).

. Press and release Learn Button. Red Learn Indicator Lightwill blink 2 times per second.

Press Remote Control Button once within 30 seconds.

Red Learn Indicator Light will stay lit.

. Press Remote Control Button again. Red Learn IndicatorLight will go out, indicating that memory is stored.

B Program each additional Remote using step A above.

Yo D_se £II Bet;isotes fl_ols_s Rowe Head Is4_Jsi}oty

A Press and hold Learn Button on Power Head for 10 seconds or

until Learn Indicator Light goes out. Memory is erased:

. Program Remotes again as needed.

'R} F:lep/a e l:&Iemote Co_t_'o/Batte y

A Push in on Battery Cover Latch at base of Remote Control(Figure 39):

. Use coin, pen, screwdriver or any similar device.

Cover snaps open.

. Replace old Battery with new _EVEREADV. A23,

12 Volt Battery.

B Snap Battery Cover closed.

WARNING

A moving garage door may cause serious injury or death.

• Keep people clear of opening while door is moving.

• Do not allow children to play with the Remote Controls.

If the Safety Reverse does not work properly:

• Close the door and disconnect the Opener using theEmergency ReleaseCord.

• Do not use the door Opener, Remote Controls, orWireless Keypad.

• Refer to the door and door Opener Owner's Manualsbefore attempting any repairs.

A Press Button on Remote Control. Garage door will move.

B Press Button again. Garage door will stop:

The door automatically stops at the end of the open orclose cycle.

C Press Button again. Garage door will reverse.

NOTE

• Each Remote Control must be programmedseparately.

• The Remote Controls will not cause the doorOpener to close the garage door if the Safe-T-Beam® System is malfunctioning.

• When programmin_ the Remote Controls, theymust be at least 24 from the Antenna Wire.

• If the red Learn Indicator Light blinksapproximately 4 times per second,programming has stopped. If programminghas stopped, repeat the above steps.

• Each Button on a 2 or 3 Button Remote Controlis for a different Opener. You cannot use morethan one Button per Remote, per Opener.

• A maximum of seven Remote Controls orWireless Keypads can be stored into theReceiver at one time. If a Remote Controlbecomes lost, or if you want to delete a RemoteControl or Wireless Keypad, see "To EraseAllReceiver Memory."

1 Button 2 ButtonRemote Remote

® ©Figure 37 Genie Remote Controls

3 ButtonRemote

@

Learn Code Button

Figure 38 Learn Code Button and Indicator Light

Visor Clip

Push to openBattery Cover

ModelNumber

Figure 39 Remote Control Battery Replacement

sn6%'_

A WARNINGA Moving door can cause serious injury or death,

1 Keep people clear of opening while door is moving.

2 Do Not allow children to play with Wireless Keypad.3 During programming, the door opener could begin

to run, so stay away trom the moving door and itsparts.To keep the door from moving, close the doorand disconnect it from the Openerby pulling theEmergency Release.

if Safety Reverse does not work properly1 Close door and disconnect the Opener using

Emergency ReleaseCord.2 Do not use door Opener, Remote Controls, or

Wireless Keypad.3 Refer to Door and Door Opener Owner's Manuals

before attempting any repairs.

NOTEFOR CONVENIENCE-- Program Keypad BEFOREmounting.

A Set Wireless Keypad PiN (Personal ID Number):• Activate programming mode.

Press (in order) @@@

Red LEDblinks - once per second.• Enteryour PIN (3to 8 characters).

• Press

Red LEDblinks - twice per second and turns off.

Programming One Door Operator: Figure 1• Find the Learn Code Button and Learn Code

Indicator LEDon your door opener.Ifyour door opener hasa black antennawire,the Learn Code Button and IndicatorLEDare located near the antenna.

(The light lens may need to be opened)Ifyour door opener doesnot have anantenna, you have an external receiver.The external receiver cover must beremoved to accessthe Learn CodeButton and Indicator LED.

• Pressthe Learn Code Button.

LearnCode Indicator LED(on Opener)will blink.

• Enteryour PINand press _.

Learn Code Indicator LEDstayson.

• Press_ again.

Learn Code Indicator LEDturns off.

Indicator

Learn l.-Code_Button

Operating One Door Operator:• To move the garage door:

Enteryour PIN.

Press_j_,.

NOTE®

®

®

If the door does not move, check the red LEDonKeypad. If the LEDis blinking rapidly, the PINwasentered incorrectly. After the LEDstops blinking,re-enter your PINand try again.

Any keypad button will control the door for30 seconds after the door starts moving.

Rapid Blinking of the red LEDindicates an error.After afew seconds the LEDwill turn off. Start over.

?_,xceec to"Mew t _'g W _ less H_y sa_:....

P eg_a_f_<s's _sg f®_ 2 O_ 3 DOH Ope_";@_s

A Set Wireless Keypad PIN (Personal ID Number):• Activate programming mode.

- Press (in order)

- Red LEDblinks-once per second.• Enteryour PIN(3 to 8 characters).

• Press

- Red LEDblinks - twice per second and turns off.

B Programming the Keypad for Multiple Door openers:

• Enteryour PINand press

- Red LEDblinks- once per second.

• Press_ again.

- Red LEDblinks - twice per second.

• Pressthe number of doors (total) you wish

tocontrol (@ or @).

• Press

- Red LEDblinks several times and turns off.

C Programming Door Openers:• Decide which door will be door #1,#2 and #3.

• Pressthe Learn Code Button (see Figure 1).

- Learn Code Indicator LED(on Opener) blinks.

• Enteryour PINand press _7_..__.

- LearnCode Indicator LEDstays on.

• Pressthe number you have picked for this

door Opener ( @ or @ or @).

- Learn Code Indicator LEDstays on.

" Press _- _}_

- Learn Code Indicator LEDturns off.

B Repeat step A above for each door opener.Eachdoor opener must be programmed to receive thesignal from the Wireless Keypad.

R_og_'ammi_ g Fog' 2 o_"3 _",i)0o_'Ope_se_s (ConUnued)

A Operating 2 or 3 Door Openers:• To move one of the doors.

• Enteryour PIN.

®

®Press door opener number ( @ or @ or @ ).

588 ;:_ E s_ ]OF * OF F*BEVOUS COLU_H

NIOUHTIH6 IHS'FI:IUC[]OH5

A Mount Keypad.(Mounting screws located insidebattery compartment.)

• Remove Battery Cover. SeeFigure 3.• Drill a 1/1d'pilot hole for the top mounting screw.• Install a screw into the drilled hole,

leaving a 1/8" gap between thescrew head and the wall.

SeeFigure 2.• Hook the Keypad over the screw.• Mark,drill pilot hole and fasten

bottom screw.

• Reinstall Battery Cover.

Figure 2

scre&ap

Figure 3

Red LED

Bottom_/ Mounting

ScrewPresshere _,-_'_ ]

x_====:d

A EnteryourPIN

• Press

B Enter theTemporary PIN(from 3 to 8 characters).

• Press b

NOTE. DO NOT reprogram the Door Opener(s).

. Temporary PIN remains active until the next time yournormal PIN is entered.

l!b. Ill] ADDKIO='d_ L i '6TBIJ ,KI IA'6[d_ [ =If {I II<_ ==11 (It=,

A Eraseold PIN:

• Press and hold in order ___},.(_ .

- Red LEDwill blinkonce and turn off.

• Release all buttons.

B Programming Door Opener(s).

• Return to"Programmin_ for 1Door Opener"or"Programming for 2 or 3 Door Openers."

Snap Lens Hinges intoslots on back of Motor Cover

60 Watts

_--_---_ maximum Push inLens _ Latches@ to

close Lens

Figure 41 Install Lens Cover and Light Bulbs

A Install two 60Watt light bulbs (not included) into LightSockets (Figure 41):

* Rough service, ] 30 Volt bulbs are recommended.

B Install Lens into slots in Motor Cover.

C Install Genie Emergency Release Kit (GER-2) accessory,

if purchased.

Installation is now complete.D

f

Transmitters comply with all United States and Canadian legal requirementsasof the date of manufacture. No warranty is made that they comply with alllegal requirements of any otherjurisdiction.lf transmitters are to be used inanother country, the importer must determine compliance with any locallaws and regulations which may differ from United States and Canadianrequirements prior to use.

Los transmisores cumplen con todas lasreglamentaciones legales de losEstados Unidos y del Canada, en la fecha de fabricaci6n. Ninguna garantiase da que cumpian con todas as reglamentaciones legales de ninguna otrajufisdiccibn. Si los transmisores sevan a utilizar en otro pals, el importadordebe determinar sicumplen con lasreglamentadones y leyes locales quepuedan ser diferentes alas reglamentaciones de los Estados Unidos y delCanada,antes de usar los mismos.

Les _metteurs sont conformes _ la r_glementation am_ricaine et canadiennecompter de leur date de fabrication. Aucune garantie n'est stipul_e

indiquant qu'ils sont conformes _ toutes les prescriptions ]uridiques d'autresautorit_s. Si les _metteurs sont utilis_s dans d'autres pays, il incombel'importateur d'en d_terminer bur conformit_ aux lois et r_gles localespouvant diff_rer de cellesdes _tats-Unis et du Canada avant touteutilisation desdits _metteurs.

Sendeger_te entsprechen allen gesetzlichen Bestimmungen in den USA undKanada zum Zeitpunkt der Herstellung.Wir Obernehmen keineGew_hrleistung for die [inhaltung aller gesetzlichen Bestimmungen inanderen L_ndern. Sollen Sendeger_te in anderen L_ndern eingesetzt werden,so muss der Importeur vor dem Gebrauch sicherstellen, dass die Sendeger_teauch sokhen [okalen Bestimmungen entsprechen, welche von denBestimmungen der USAund Kanadasabweichen.

x@a}_lOll_xl nI_[ 9_L}E_-_°-4_--_-A_j_l__ EF_XI_---e-bC[Xt_°l

A Monthly:• Door springs and door hardware:

- Oil door roller, bearings, and hinges using siliconelubricant or light oil.

WARNINGDo not operate door automatically or manually if springsare broken. Contact a Genie Factory Authorized Dealer forservice or call Customer Service at 1-800-3S-GENIE.

• Balance Door.

Closedoor.Release Magnetic Carriage Assembly from Rail Assemblyby pulling down on Emergency Release Knob.Raise door manually 3'- 4' and verify that door stays atthat position. SeeCheck Step 2 on page 3.

NOTEWhen the door is 3'- 4' above the ground, the doorshould stay open. Slight movement is acceptable. Ifthe door moves too much, contact a Genie FactoryAuthorized Dealer for service or call Customer Service at1-800-35-GENIE.

Reattach Magnetic Carriage Assembly to Rail Assembly:a. Pull the Emergency ReleaseKnob toward Power Head.b. Close door.

Contact Reverse Test.

Perform Installation Step 10 on page 21.

WARNINGIf the door fails to reverse on contact with the board,adjust the Close ForceControl as specified in Set LimitSwitches and Force Controls on page 20. If the Openerstill fails, contact a Genie Factory Authorized Dealer forservice or call Customer Service at 1-800-35-GENIE.

B Yearly:

+ Wipe off old excess lubricant from Drive Screw.+ Lubricate Drive Screw with Genie Lubricant (GLU-3)

NOTEUse ONLY Genie Lubricant (GLU-3). Other lubricantsmay damage the Opener.

GLU-3

Lubricant

FCC AND IC CERTIFIEDAll devices comply with Part 15 of the FCCRules.Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received, includ-ing interference that may cause undesired operation.

WARNINGTO REDUCE THE RiSK OF SEVERE iNJURY OR DEATH

1 READAND FOLLOW ALL INSTRUCTIONS.

2 Never let children operate or play with the Door Controls. Keep the Remote Control away from children.

3 Always keep the moving door in sight and away from people and objects until the door is completely closed.NO ONE SHOULD CROSSTHE PATHOF THE MOVING DOOR.

4 NEVERGO UNDER A STOPPED,PARTIALLYOPEN DOOR.

5 Test Opener monthly. The door MUST reverse on contact with a 1-1/2" high object (or a 2" x 4" board laid flat)at the center of the doorway on the floor. After adjusting either the Force or the Limit of travel, retest the DoorOpener. Failure to adjust the Opener properly may cause severe injury or death.

6 When possible use the Emergency Release only when the door is closed. Use caution when using this Releasewith the door open. Weak or broken springs are capable of increasing the rate of door closure and increasingthe risk of severe injury or death.

7 KEEPGARAGE DOORS PROPERLYBALANCED. See Owner's Manual. An improperly balanced door increases therisk of severe injury or death. Have a Genie Factory Authorized Dealer make repairs to cables, springassemblies, and other hardware.

8 SAVETHESEINSTRUCTIONS.

, WARNINGUsethe Wall Console included with Opener. Any other wall console can cause the Opener to operate unexpectedly andthe light to stop working.

TI%, yUBLEJHO,, y GUIDE

Source (Red LED)

ON

OFF

OFF

2 BLINKS, Pause

(Repeat)

2 BLINKS, Pause

(Repeat)

3 BLINKS, Pause

(Repeat)

4 BLINKS, Pause

(Repeat)

Sensor (Green LED)_z_z

ON

OFF

ON

ON

OFF,J

ON

ON

Possible Problem

Normal operation

• Power Head not powered

• Wiring from Power Head bad

• Wiring to Source missing or bad

• Beam not aligned• Beam obstructed

• Sensor defective

• Wire to Sensor missing or bad• Sensor defective

• Sensor receiving interference

• Source not sending pulses• Source defective

Solution

None required

• Check breakers, fuses,plugs• Checkwiring for obvious shorts

• Check wiring

• Check Source, Sensor alignment• Check for obstruction• Contact Customer Service

• Check wiring• Contact Customer Service

• Determine source of interference• Contact Customer Service

• Contact Customer Service

• Contact Customer Service

• See Status Light on Figure38, page 22)

You See

1 BLINK,Pause

(Repeat)

2 BLINKS,Pause

(Repeat)

3 BLINKS,Pause

(Repeat)

4 BLINKS,Pause

(Repeat)

5BLINKS,Pause

6 BLINKS,Pause

7 BLINKS,Pause

8 BLINKS,Pause

Problem

Motor DriveBoa rd

Normal

operationrestored

If the problemrecurs

Operation notrestored

ControllerBoa rd

Interrupt

OpenerOverheated

or

Force SettingsIncorrect

Safe-T-Beam ®Malfunction

Wall Consoledoes not work

Limit Switches

not working

Wall Consolelocked

What to Do

• Reset Opener--unplug (or disconnect power), wait 5 seconds, plug

back in (reapply power), and activate from Wall Console.

• First Cycle will run at slow speed.

automatic garage door balance detection system. An improperlybalanced door, damaged or worn counter-balance spring, bindingdoor hardware or rollers may result in a "ONE-BLINK" signal.

• Contact Customer Service for further assistance.

Check door condition.

Have a Genie Factory Authorized Dealer check:- Fuse on Motor Drive Board.

- Ribbon Cable on Motor Drive Board is properly inserted intoConnector on Controller Board.

Reset Opener- unplug (or disconnect power), wait 5 seconds, plugback in (reapply power), and activate from Wall Console.Have a Genie Factory Authorized Dealer check that Ribbon Cable onMotor Board is properly inserted into connector on Controller Board.

• Do not unplug or disconnect power from Opener. Wait 10 minutesfor internal clock to provide additional cycles. Cycles are restoredat a rate of S cycles per 10 minutes of rest.

• Check Force Settings. NOTE: Force Settings are not pre-set at factory.Check door condition.

Check Safe-T-Beam ® Self-diagnostk System. NOTE: Safe-T-Beam ®System must be installed and operational to enable door to close.

• Check Wall Console Wiring for shorts, tight Staples, or pinched Wires.Check Wiring Connections at Power Head and Wall Console.

Check Limit Switch Wire connections to Terminals on Power Head.

Check for shorted or pinched Wires under Limit Switch Brackets.

Vacation Locking Switch on Wall Control is in "Lock" mode.Unlock switch.

NOTE

Reference

See Door

Safety Guide

1. See page 3.2. See door

Safety Guide

1.See page 20.2.See Door

Safety Guide_

See page 16.

See page 18.

See page 20.

See page 18

The status LED Indicator Light is located under the Lens Cover.The Green LED light will turn ON,then OFFwhenpower is applied to the Opener. If LED stays ON, have a Genie Factory Authorized Dealer check the ControllerBoard, or call Customer Service at 1-800-35-GENIE.

®If Safe-T-Beam problems exists, the door can be closed electrically by holding the Wall Console Button downuntil door is fully closed.The Remote Controls and Wireless Keypad will not work without a working Safe-T-Beam® System.

Problem What To Do

Opener does not run 1. Check power source.from Remote Control A. If Opener is connected to an outlet:

• Plug a working lamp into outlet used for Power Head.. If lamp glows, power source and outlet are OK.• If not, check fuse or circuit breaker or non-compatible GFCI.NOTE: A licensed electrician must replace non-compatible GFCI's.

B. If Opener is connected to a wiring box:• Check fuse is not blown, or circuit breaker is"CIosed"(not tripped).• If still no power, have a licensed electrician check circuit and wiring.

2. If power is OK:• Check connections at Power Head Terminals (seeWall Console Installation page 18), tightening any

loose connections.

Have a Genie Factory Authorized Dealer check that Ribbon Cable between Controller Board and Motor DriveBoard is properly connected to Connectors on Circuit Boards, or call Customer Service at 1-800-35-GENIE.

Door Opener starts • Check Wires to ensure that they are not cut (Stapes can cut insulation and short Wires).for no apparent reason Replace any shorting Staples and shorted Wires.

• WasRemote Control lost or stolen? If so, eraseall Remote Control codes from Receiver's memoryand reprogram for remaining remote controls. (SeeEraseAll Receiver Memory on page 22).

Door starts down, then . Check Close Limit Switch setting (see Set Limit Switches and Force Controls on page 20).stops before it is Adjust as needed.completely closed • Checkfor shorted Wires.

• Check aragedoor for binding

Door starts down, then . If a new installation, check Door Arm position.stops and goes back up . Check operation of Contact Reversefunction.

. Check Safe-T-Beam6)System for beam obstruction or misalignment of Lenses.Check Safe-T-Beam= System diagnostic code.

. Check CloseForceadjustment (seeSet Limit Switchesand ForceControls on page 20). Adjust as needed.• Check garagedoor for binding.

Door will only run closed • Check Open Limit Switch for a short circuit and for proper wiring.. Check Open Force adjustment (seeSet Limit Switchesand ForceControls on page 20). Adjust asneeded.• Check condition of garage door and door spring(s).• /!5\;_' /_6: If you suspecta problem with the garage door hardware or springs,contact a Genie

FactoryAuthorized De aler for service,or contact Customer Serviceat 1-800-35-GENIE.

Door will only run open . Check Safe-T-Beam_ System asdetailed in the Safe-T-Beam6)System Self-diagnosticTroubleshooting Chart(seeSafe-T-Beam_ SystemSelf-diagnosticTroubleshooting Section on page 26).

• Check CloseLimit Switch for a short circuit and for proper wiring.• Check CloseForceadjustment (seeSet Limit Switchesand ForceControls on page 20). Adjust as needed.

Lights will not turn off . Disconnect Wires connecting WallConsole to Power Head (seeWall Console Installation on page 18).

Checktheir condition and either replaceor reconnect.• Until a replacement Wall Consolecan beobtained, disconnect Wall Consoleand useonly Remote Controls

or WirelessKeypadto operate Opener.

Door starts up, but stops • Check (ensure) that garage door and Opener are in good repair, properly lubricated, and properlybefore it is balanced as detailed in Maintenance Section.

completely open ,. STA_::_I_P,6: If you suspect a problem with the garage door hardware or springs,contact a GenieFactory Authorized De aler for service,or contact Customer Serviceat 1-800-35-GENIE.

• Check Open Limit Switch for a short circuit and for proper wiring.

• Check Open Forceadjustment (seeSet Limit Switchesand ForceControls on page 20). Adjust as needed.

Operator runs,but door . EnsureMagnetic CarriageAssembly is engaged to RailDrive Screw(seeInstall Magnetic Carriage Assemblydoes not move onto Railson page 10).

o Check Forceadjustment (seeSet Limit Switchesand ForceControls on page 20). Adjust as needed.• Checkthat all sectionsof RailDrive Screware turning when Motor runs. If not:

- Checkcondition (not cracked,split,or broken) and placement of Coupler. Replaceas needed.- Checkcondition (not cracked,split,or broken) and placementofCollarandClip. Replacethem

as needed.

Wall ConsoleVacation • EnsureMagnetic CarriageAssembly is in contact with Close Limit Switch.Lock function does • Checkwhen door isfully closed,that Carriageactivates CloseLimit Switch. If not,adjust position of Closenot work Limit Switch (Seepage 19).

_ R Is "i S}O 35 6IN _: st vs}; www !s}_<!' e<:os<Iat_7,+';oIs '

What To DoProblem

Remote Control has less

than 25' operating range

Opener works from WallControl, but not fromRemote Control

Noisy operation

Safe-T-Beam®System

Door closes,and Openershuts clown

. Relocate Remote Control inside car.

. Ensure Remote Control is pointing toward garage door when pressing Control Button.• Replace Remote Control Battery _EVB?EAD_ type"A23." (See page 22).

• Reposition Opener Antenna Wire.• Do Not attem t to retune Remote Controls or Receiver

• Program code for each Remote Control into Receiver memory (SeeProgramming the RemoteControl on page 22.

. Replace Remote Control Battery _EIfB?EAD_ type"A23." (See page 22).• Check Safe-T-Beam®System for beam obstruction or misalignment of Lenses.• Check Safe-T-Beam®System for any diagnostic codes. If present, troubleshoot as detailed in

Safe-T-Beam®System Self-Diagnostic Troubleshooting Chart (Seepage 26).

• Ensure all fasteners are tightened.• Check that the garage door and Opener are in good repair, properly lubricated, and properly

balanced. (SeeMaintenance page 25).• If you suspect a problem with garage door hardware or springs, contact a Genie

Factory Authorized Dealer for s rvice,orcontact Customer Serviceat 1-800-35-GENIE

• If an operational problem exists, Opener will not run closed.• Check Safe-T-Beam®Systemfor beam obstruction or misalignment of Lenses.• Check Safe-T-Beam®Systemfor any diagnostic codes. If present,troubleshoot asdetailed in Safe-T-Beam®

SystemSelf-DiagnosticTroubleshooting Chart (Seepage 26).

• Check position of Wall ConsoleVacationLockSwitch. It must be in UNLOCKEDposition for Opener toopen door.

WALL CONTROL

m

_u

i-o3

WHITE

1 WHITE __

i OPEN LIMIT z

Opening Cover May Cause Electric Shock [

CONTROLLER BOARD

-@

®

-@

J_

-@

PRIMARYGROUND

MOTOR DRIVE BOARD

GREEN

l LiNEPLUG

I 9 BLUE

I 8 BLACKWHITE

6WHITE

5

_ o

MOTOR

GREEN

_1_SECONDARYGROUND

What sC_veed

Any defect in material and workmanship from personal, normalhousehold use in accordance with the Owner's Manual.

HSOOODSeries -- Lifetime _ on motor, on parts and service,

ISDggO Series -- Lifetime _ on motor, I years _ on parts.ISDggO-2 Series -- Lifetime _ on motor and all parts.

ISDgg5 Series -- Lifetime _ on motor and all parts.

ISDggS-2WKM Series-- Lifetime _ on motor and all parts.

ISDI000 Series -- Lifetime _ on motor, all parts and service.

CMD9900 Series -- Lifetime _ on motor, 5 years _ on parts.PRO99 Series -- Lifetime _ on motor and all parts.

for as long as you own your home.This warranty is non-transferable.

This warranty applies only to the consumer who originally purchasedthe product.

This warranty applies only to Genie products purchased in the UnitedStates and Canada.

If your Genie product is defective, we will send replacement parts or, at

our option, a replacement unit at no charge to you, excluding shipping,

handling and labor costs. If we send replacement parts for your Genie

product, we may use new or reconditioned parts. If we choose to send

a replacement unit, we may use a new or reconditioned one of thesame or similar design.

IMPLIED WARRANTIES, INCLUDING THOSE OF FITNESS FOR A

PARTICULAR PURPOSE AND MERCHANTABILITY (AN UNWRITTEN

WARRANTY THATTHE PRODUCT IS FIT FOR ORDINARY USE) ARELIMITED TO ONE YEAR FROM DATE OF PURCHASE. GENIE WILL NOT PAYFOR: LOSS OF USE OF YOUR GENIE PRODUCT OR PROPERTY DAMAGE

CAUSED BYYOUR GENIE PRODUCT OR ITS FAILURE TO WORK; ANY

SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES; ANY DAMAGESRESULTING FROM MISUSE OR MODIFICATION OF YOUR GENIE PRODUCT.

Some states and provinces do not allow limitations on how long an

implied warranty lasts or the exclusion of incidental or consequential

damages, so the above exclusions and limitations may not apply.

This warranty is the only one we will give on your Genie product, and

it sets forth all our responsibilities regarding your Genie product.There are no other expressed warranties.

State and Province Rights: This warranty gives you specific legal rights,

and you may also have other rights that vary from state to state and

province to province.

MOW 06et' ""_, = 1= +' / ?_f]_

To get warranty service for your Genie product, you mustprovide proof of date, and place of purchase of the product.

Call Genie Customer Service toll free at 1-800-354-3643, or visit

our website at www.geniecompany.com.Trained Genierepresentatives will assist in diagnosing the problem and will

arrange to supply you with the required parts for do-it-yourself

repairs.Trained service representatives are available Monday -

Friday, 8:00 AM - 11:00 PM, and on Saturday, 11:00 AM - 8:00 PM

Eastern Time (subject to holidays).

You can obtain the name of a Genie Factory Authorized Dealer

by calling the Genie Dealer Locator Service at 1-800-654-3643.

If an Authorized dealer provides warranty service, Genie will not

reimburse you or otherwise be responsible for any laborcharges, Your choice of one of the above described service

options is your remedy under this warranty.

. Batteries (which are considered replacement parts)

. Installation

. Commercial use

. Defects resulting from accidents

. Damage while in transit to our service location or damagefrom alterations

Misuse or Abuse

Lack of proper maintenance

Unauthorized repairs or modifications of the product

Affixing of any attachment not provided with the product

Programming of Remote Control Devices

Programming of Keypads

Safe-T-Beam _"_adjustment/cleaning

Staples through wiring

Pinched or broken wires

Carriage disengaged

Force Control adjustments

Door out of balance

Broken springs or cables

Power outages

Use of extension cords

Missing or damaged parts on discounted, clearanced, final

sale or taped cartons

. Phantom operations

. Fire

. Flood

. Acts of God

. Failure to follow the Owner's Manual

¢o®sse _®s _f;;,_eufeuw'e,_;;,ey'l;ed_og......_4_

(GIT-1)DeluxeRemoteControlwith Intellicode- Allowsremoteoperationof garagedoorControladorremotode lujo con Intellicode®-Proporci6naroperaci6nremotode lapuertadelgarajeT_lecommandede luxe avecIntellicode-Permettreoperation@loign'deportede garage

(GIT-2)2-ButtonRemoteControlwith Intellicode®-Allowsremoteoperationof2 garagedoorsControladorremotode 2 funcionesconIntellieode'- Proporci6naroperaci6nremotode doslas puertasdelgarajeT_l_commande_ 2 fonctionsavecIntellJcode_-Permettreoperationeloign'deuxportesde garage

(GIT-3)3-ButtonRemoteControlwith Intellicode®-Allowsremoteoperationof 3garagedoorsControladorremotode 3 funcJonesconIntellieode®-Proporcidnaroperacidnremotode treslas puertasdelgarajeTel_eommande_ 3 fonctionsavecIntellJcode®-Permettreoperation61oign'troisporfesdegarage

(GPWC-2WLB)LightedWailConsole - OperatesGarageDoor IndependentlightcontrolSecurityvacationlockConsolade paredde 3 funciones- Accionalapuertadelgaraje.Controldeluz independiente.CerraduradeseguddadparavacacionesConsolemurale_ trois fonctions -Actionnelaportede garage.Commanded'edairageind@endanteInterrupteurdeverrouillagede s@urite

(GMI-3)3-ButtonMini RemoteControlwith Intellicode - FitseasilyintopocketorpurseMinicontroladorremotode 3 funeionesconIntellicode®-Cavefacilmenteen elbolsilloo carteraMinit_l_commande_ 3 fonctJonsavecIntellieode' -seglissedanslapochede vestonou lesaca main

(GWKP)WirelessKeypadEntrySystem-OperatesInte@ode_GarageDoorOpenerswithoutRemoteControlorkeySistemade entradapor tecladonum_ricoinalambrico-Accionalos abridoresde puertasde garajeIntellicode_sincontrolremotoo Ilave

a_5 Syst_med'ouvre-portede garage_ claviersans fil- Actionnelesouvre-portedegarageavectnte]licode®sanst_l@ommandeniciezw (GLU-3)f/4 oz.TubesScrewDriveLubricant(3)- EnsuresproperequipmentwearprotectionLUz 1/4onceLubricantede tornillo accionar(3)- Aseguracomponentecorrectoproteccidnpotdetefioro_D Laonza1/4Lubricantde la vie (3)- Garantircomponantexactparsystcmedefenseversuser

_< (GWB)UniversalWall Button- Providesadditionalconvenientinsideoperationof door_u Bot6nde pareduniversal- ProporcionaoperaciOnconvenientedela puertadesdeel interior

Boutonmuraluniversel- ActionneI'ouvre-portede rintCrieurdu garage<_:_: (GPS-5)PerfectStop®-Ensuresperfectparking

¢_< Stop Perfecto- Aseguraelestacionamientoperfecto®ButoirPerfectStop - Permetde stationner8 laperfectiondartslegarage

OI-

z (GSXL-8)ExceleratorScrewDriveExtensionKit- AneighteeninchExtensionto increasethetravelof a ScrewDriveOpenertoaccommodateaneightfootdoorElextensi6ndeslizantede ExceleratorScrewDrive- Unaextensionde18pulgadasparaaumentarlacarreradeunabridordeslizabbdetomilio,paraacomodarunapuertade8 pies(2,43m)

u_ N_cessairederallongedu ExceleratorScrewDrive- Rallongede 30dm(18pc)prolongeant]acoursede I;ouvre-porteScrewDrivepouruneportede 2,4m (8pi)de hauteur£3

<l:u_ (GIRU-tT)UniversalConversionKit- ConvertsanyGarageDoorOpenerto asecureradiosignalsystemKit includesa RemoteControl,ReceiverandTransformerz

','2 Juegodeconversi6nuniversal-Conviertecualquierabridordepcertadegarajea unsistemadeserialderadioseguro.Eljcegoinduyeuncontrolremotodeabridordepuertadegaraje,_< receptory transformadorz Necessairedeconversionuniversel-Transformetoutouvre-portede garageensystcmedes@urit_a signalradioComprendunet_i@ommanded'ouvre-portedegarage,unr_cepteuret

untransformateur

o 60WATTEnhanced/RoughServiceLight Bulb- Ensuresproperequipmentcompatabilityz< Bombillade 60Vatios- Aseguracomponentecorrectodesistema_: Eelairagede 60WATT-Garantircomponantexactparsysteme

u_ (GER-2)EmergencyReleaseKit- Providesaccessto garagefromoutsideintheeventof anelectricalpowerfailurezJuegodepica-portede pestillo- Permitirentrtadadesdepotfuerade garajeporquecortedeel@triceN_cessairesde D_clenchementde secours- Le necessairede d@lenchementdesecoursestconpupourvouspermettred'acc_dera votregaragedepuisIext¢rieurencasde pannede

_- courantet Iorsqu'il

c_ STBAdapterBrackets(2)- UsedinconjunctionwithstandardSTBMountingBracketsTheyprovideadditionalclearancealongwithmountingoptionsz Eladaptadorponeentre par_ntesis(2)- Usadoen unionconpar_ntesisuniformesde montardeSTB,ellceproporcionanel espaciolibreadicionaljuntoconmortarlasopcioneso Crochetsd'adaptateur- UtiliseconjointementavecSTBstandardmonterles crochets,!isfournissentledegagementsupplementaireavecmonterd'options<

<uJI-

No C.OD shipments Please include check or money

order, made payable to The Genie Company Do not

send cash. Allow 3-4 weeks for delivery. We accept

Visa or Mastercard on phone orders only

1-800-354-3643 Please have part number and credit

card ready

Please add local sales tax if you reside in one of

the states listed.

California indiana

Connecticut MarylandFlorida Massachusetts

Georgia New JerseyIllinois New York

TOTAL ORDER

SHIPPING & HANDLING

STATE SALES TAX

GRAND TOTAL

OhioTennessee

VirginiaWisconsinMichigan

$

$ 500

$

$

No se aceptan pedidosde pago contra entrega (COD).Sirvase inc]uir su cheque o giro postal, la cuentapagadera hechaa The Genie Company. No enviedinero en efectivo Concedanos3 a 4 semanas para laentrega. Aceptamos pedidos telef6nicos de Visa oMastercard. 1-800-354-3643.Sirvaeetener listos losnQmerosdel modelo y de la tarjeta de credito.

Sirvaee agregar el impuesto de ventas local si ustedreside en uric de Ice siguientes estados:

California Indiana

Connecticut MarylandFlorida Massachusetts

Georgia New Jerseyillinois New York

TOTAL DEL PEDIDO

FLETE Y MANEJO

IMPUESTO DE VENTAS ESTATAL

GRAN TOTAL

OhioTennesseeVirginiaWisconsinMichigan

$

$ 580

$

$

Isst_'uct o_'ssCommssds_tPasd'expeditioncontreremboarsement.Veai]lezinclureunchequeou un mandatbancaire,le payablefaira TheGenieCompany. N'envoyez pas d'argent comptant. Accordezde 34 semainespourtalivraison.Nousacceptonslescommandespartel@honeavecpaiementparcartede creditVisaouMastercard1-880-354-3643.Ayezsouela mainlenumerodelapieceet celuide lacartedecredit

Veuillez indiquer leetaxesdevente locales eivous r_sidezdane I'undes_tats r_pertori_s ci-dessous.

Californie Indiana OhioConnecticut Maryland TennesseeFloride Massachusetts VirginieGeorgie New Jersey WisconsinIllinois New York Michigan

COMMANDE TOTALE $

MANUTENTION ET EXPEDITION $ 508

TAXE DE VENTE $

TOTAL GLOBAL $

Prices on Reverse Los Precios en otro lado Les Prix sur I'autre cote

GEI IE

3-ButtonRemoteControlwith Inte!/code®Contrdadorremotede 3 funcionescon Intelicode_'TelGcommandea 3 fonctionsavecIntellicode_'

MODEL DESCRIPTIONMODELO DESCRIPCIONMODELE DESCRIPTION

DeluxeRemoteControlwith Intellcode®

GIT-I Contreladerremotode lujo conInte!/code®Tel@ommandede Bxeavec Intelicode®

2-ButtonRemoteControlwith Inte!/code_GIT-2 Controladerremotode 2 funcionescon inteilicode_">

Tel@ommandea 2 fonctionsavecIntellicode®

GIT-3

LightedWa/ConsoleGPWC-2WLBConsolade paredencender

3-ButtonMiniRemoteControlwith Intelicode<_'Minicontroladorremotode 3 funciones

GMI-3conIntelicode_'Minitel@ommandea 3 fonctonsavecIntelicodd_

GWKP

GLU-3

WirelessKeypadEntrySystemSistemade entradaper tecladonum@icoinalambricoSystemed'ouvre-portede garage£ claviersansfil

PRODUCTCODECODIGO

CODEDUPRODUIT

1/4oz,TubeScrewDriveLubricant(x 3)1/4onceLubricantede torn/Io accionar(x 3)Laonza 1/4Lubrifiantde lavis (x 3)

UniversalWail Button(unlit)Bot6nde pareduniversal(unlit)Boutonmuraluniversel(unlit)

PerfectStop_'StopPerfecto_"ButoirPerfectStop_'

PRICE(US$)*_iQTY,PREClO* iCANTIDAD

PRIX($US)*i QTE

33069R $34.95

33069S $44.95

33069T

34292R

34909R

35282R

34965R

34960RGWB

GPS-5 34964R

GSXL-8 33523S

$49.95

$13.95

$39.95

$49.95

TOTALTOTALTOTAL

$t .95

$4.95

$4.95

$34.95

611"-1

GIT=3

ScrewDriveExtensionKit(For Excelerator)Elextensi6nde cadenadesfzable(ParaExceJerator)N@essairede prolongementducoulsseau(PourExcelerator)

i-IGPWC-2WLB

GWKP

LU-3

GWB @

GPS-5

GSXLoM

UniversalConversionKit

GIRU-IT Juegodeconversi6nuniversal 33154RNecessairede conversionuniversel

60WattEnhanced/RoughServiceLightBulbLIGHTBULB Bombilade 60Vatios 26210A,S

Edakagede 60Watt

EmergencyReleaseKitJuegode pica-portede pestilo 34963RN@essairesde d'clenchementde secours

GER-2

ADAPTERBRACKET

$49.95

...........................

$2.95

$29.95

STBAdapterBrackets(2)Eladaptadorponeentre par@tesis(2) 34439R.S $4.95Crochetsd'adaptateur(2)

G,RU-,T

LIGHT BULB

GER-2

8TB BRACKETEXTEN81ON8

LUl

sj_z!21sjuJlZl©I

<I

wl

_dC31

Szl

<I

zlwl

<I

wlzl

c31

ol

<I

* Prices subject to change without notice* Valoran el cambio con sujecidn a sin nota* Les prix assujettissent pour changer sans ta notification

@t " s/1"4 , I:11'

;:NV/tP/i/l::t _ I'll w!e

NAME/NOMBRE/NOM

ADDRESS/DIREC@ON/ADRESSE

CITY/QUDAD/VILLE STATE/ESTADO/ETAT ZIP/CODIGO POSTAL/CODEPOSTAL

I/IAilo OHDL£ROR/F "O:

_ic Rc ,.,. ,'0,:, c .c _,-.RR,..,, cv_:;_ A:

The Genie Company22790 Lake Park Blvd.

Alliance, Ohio 44601-3498