your trusted partner in api 6a valves & manifolds

Your trusted partner in API 6A Valves & Manifolds

2

Index1. API 6A Gate Valve 32. Hydraulic Actuated FC Gate Valve 53. ESD API Gate Valve 64. Hydraulic Actuated DA Gate Valve 75. Materials & inlay 86. Electric Actuated Gate Valve 97. Mud Gate Valves 108. Design & Manufacture of Manifolds 129. Service & maintenance 14

10. Spare parts 1511. API 6A Gate Valve specification 1712. Manual specification 1813. Hydraulic Actuated specification 1914. MV50 Mud Valve specification 2015. MV75 Mud Valve specification 2116. Torque to Flange & Bonnets 2217. Lubrication 2618. API 6A Valves & Manifolds 2719. Ring Gaskets 4220. Chart Gasket & Studs 4321. P/N Gasket & Studs 4422. Other API Valves & Manifolds 45

31. API 6A Gate Valve

E-type through conduit gate valveAnson through conduit gate valve was developed in 1991 to satisfy the need for a high-quality, high-specification valve. The E-Type is a true bi-directional valve with low operating torque. It is robust, easy to maintain, and is supported by Mento`s aftermarket teams.

Anson gate valve technology is used across various applications -well testing, flowback, drilling, exploration, production, and well intervention. This field-proven design with multifunctionality makes the E-Type gate valve one of the most trusted valves in our ever-changing industry.

Specification• Uses no performance-limiting elastomers • Available from 2,000 to 20,000 psi in sizes 1 13/16” to 9-in. bore • Designed, manufactured and tested in accordance with API 6A Material class, temperature range, product specification level (PSL) as per API 6A • API 6A monogramed • Qualified for Class lI Sand Service (API 6AV1) • Qualified for high-pressure/high-temperature (HPHT) service (API6A annex F PR2 to 350 deg F(177 deg. C)) and extreme low-temperature service (API 6A Annex F PR2 to -75’F)

API 6A Gate valves

E-type through conduit gate valveAnson through conduit gate valve was developed in 1991 to satisfy the need for a high-quality, high-specification valve. The E-Type is a true bi-directional valve with low operating torque. It is robust, easy to maintain, and is supported by Mento`s aftermarket teams.Anson gate valve technology is used across various applications -well testing, flowback, drilling, exploration, production, and well intervention. This field-proven design with multifunctionality makes the E-Type gate valve one of the most trusted valves in our ever-changing industry.

Specification• Uses no performance-limiting elastomers • Available from 2,000 to 20,000 psi in sizes 113/, 6 to 9-in. bore • Designed, manufactured and tested in accordance with API 6A Material dass, temperature range, product

specification level (PSL) as per API 6A• API 6A mongrammable• Qualified for Class lI Sand Service (API 6AV1)• Qualified for high-pressure/high-temperature (HPHT) service (API 6AAnnex F PR2 to 350'F) and extreme low-

temperature service (API 6A Annex F PR2 to -75'F)

Features

Body and bonnet: Integral one-piece forged body and bonnet with minimal pressure boundary penetrations

Gate and seat design: The seats in the E-Type gate valve are fully floating. This, combined with a solid slab gate, gives a true downstream seal resulting in exceptionally low operating forces. Gate and seat replacement are possible with the valve in line, without the need for special tools.

Bi-directional sealing: The E-Type gate valve is a true bi-directional valve. Being fully symmetrical, it effectively seaIs pressure fromeither direction without the risk of pressure lock.

Body to bonnet seal: A sea I is achieved between the body andbonnet using metal-to-metal seaIing technology. The seaI is reusable.

SeaIs: The E-Type gate valve uses high-performance PTFE seaIs withCRA spring energizer and uses no performance-limiting elastomers.

Handwheel: The E-Type gate valve is supplied with a rugged handwheel that employs a double detent quick-release mechanism. A shear pin is provided to protect the valve's internals from damageand is replaceable without having to dismantle the valve or take it out of line.

API 6A Gate valves

4

FeaturesBody and bonnet: Integral one-piece forged body and bonnet with minimal pressure boundary penetrations

Gate and seat design: The seats in the E-Type gate valve are fully floating. This, combined with a solid slab gate, gives a true downstream seal resulting in exceptionally low operating forces. Gate and seat replacement are possible with the valve in line, without the need for special tools.

Bi-directional sealing: The E-Type gate valve is a true bi-directional valve. Being fully symmetrical, it effectively seaIs pressure from either direction without the risk of pressure lock.

Body to bonnet seal: A seaI is achieved between the body and bonnet using metal-to-metal seaIing technology. The seaI is reusable.

SeaIs: The E-Type gate valve uses high-performance PTFE seaIs with CRA spring energizer and uses no performance-limiting elastomers.

Handwheel: The E-Type gate valve is supplied with a rugged handwheel that employs a double detent quick- release mechanism. A shear pin is provided to protect the valve’s internals from damage and is replaceable without having to dismantle the valve or take it out of line.

1. API 6A Gate Valve features

PTFE stempacking (one piece)

Grease injecton port above stem back seat

Reusable metal bonnet seal

Forged body and bonnet

PTFE seat seal for superior low-pressure performance

Fully floating gate and single-piece seats, metal-to-metal primary sealing seal

5

Fait-Safe Close and Fail-Safe OpenFail-safe close (FSC) and fail-safe open (FSO) E-Type gate valves are designed with fail safe spring return actuators, offering a flexible solution for ernergency shutdown valves (ESD) and other fail-safe applicat-ions. Fluid is applied to one side of the piston to move the gate, and a spring within the cylinder generates the energy for the opposite motion. The fail-safe actuator is a self-contained unit that allows for quick removal from the valve bonnet if necessary when the valve is still under line pressure. The design also allows for quick and easy main-tenance, and no drift adjustment is necessary to set the stroke.

Features

• Linear hydraulic single acting spring return • Normal operating pressure of 3,000 psi (4,500 psi max) • Translating hydraulic cylinder • Compact design • Hard-chrome plated cylinder • The T-slot connection between stem and gate • Multi-lipped pressure and spring energized stem seals • Fully weather sealed • Automatic back seating fire resistant • Twin guide bearings for stem • Pressure relief port above valve stem packing

• No drift adjustment required to set the stroke • API 6A Annex F PR2F qualified

Options

• Safety head device fitted to prevent damage to valve or actuator • Can be supplied as part of an Emergency Shutdown Valve assembly • Quick exhaust valve can be included for optimal shutdown time • Position indication by rising stem, clear inspection plate or limit switch feedback

2. Hydraulic Actuated FC Gate Valve

Hydraulically Actuated E-Type Gate Valves

63. ESD API Gate Valve

We provide Anson E-Type fail-safe valves as part of a complete emergency Shutdown (ESD) valve assembly. Generally situated upstream of the choke manifold, the standalone ESD valve is used to safely and quickly isolate the downstream equipment from the high-pressure wellbore fluids. These valves are critical to protecting personnel, equipment and the environment.

The ESD is used in conjunction with a control system to allow the valve’s remote operation. Closure times can be critical, and the ESD valve can be enhanced with the inclusion of a quick exhaust valve in the hydraulic return line, shutting the valve in less than five seconds.

Generally, the ESD valve will be supplied enclosed in a skid frame and include inlet and outlet crossovers. Skids can be provided per DNV 2.7-1.

We also supply wellhead pneumatic surface safety valves, as part of our surface safety products (SSP) product line. lncluding Axelson’” type actuators, we have the most extensive offerings of remote-controlled monitoring and actuator systems in the industry. Our SSP pneumatic actuator can be supplied with the Anson E-Type body and internals, incorporating two field-proven and trusted product lines.

Emergency Shutdown Valves

7

Anson E-Type gate valves are available with double acting (DA) hydraulic actuators and double Acting with manual override (DAO). Fluid is supplied to connections below and above the piston, the pressure operates the valve, and in turn the gate to open or close.

Features

• Linear hydraulic double acting • Normal operating pressures of 1,500 or 3,000 psi • Compact design • Robust enclosure • Double hydraulic piston seaIs and guide rings • Fully weather sealed • Position Indication by a rising stem, limit switch feedback

Options

• Manual override (DAO) with a handwheel • Position lndication by a rising stem, limit switch feedback

4. Hydraulic Actuated DA Gate Valve

Double Acting Actuator

85. Materials & inlay

Additional corrosion protection can be applied to certain areas of the gate valve to increase the service life of the equipment. For material classes

DD through to FF, CRA 625 weld overlay can be applied to all ring grooves, body seat pockets, stem seaI and bonnet seal area.

Enhanced Corrosion Protection

The table below shows the options available with the Anson E-Type gate valve. The trim level chosen is dependent on the severity of service anticipated

over the lifetime of the valve. It is possible to up-grade a lower specification of E-Type should more severe service be encountered later in the valve’s life.

API 6A Materal Classes (Trim Levels)

Material Class Body/Bonnet Gate/Seat StemAA AISI4130 (API 75k) AISI4130 (API 75k) AISI4140 hardenedBB AISI4130 (API 75k) ASTM A564 Type 630 (17-4PH) CRA718 or CRA725DD* AISI4130 (API 75k) AISI4130 (API 75k) AISI4140 hardenedEE* AISI4130 (API 75k) ASTM A564 Type 630 (17-4PH) CRA718 or CRA725FF* ASTMA182 F6NM (Mod) ASTM A564 Type 630 (17-4PH) CRA718 or CRA725HH* ASI4130 (API 75k) c/w CRA 625 CRA 718 CRA718 or CRA725

*Suitable for sour gas service and certified in accordance with NACE MR-01-75/ISO15156

NOTES:1. Other material options are available on demand.2 Grease fitting rated as per valve material class.

Ring JointSeal Area

Seat PocketSeal Area

BonnetSeal Area

StemSeal Area

96. Electric Actuated Gate Valve

Convert your existing Anson ™ E Type Manual Gate Valve to electric actuation with our Electric Actuation Conversion Kit . The kit can be easily installed without breaking the pressure seal between the bonnet and body , meaning post installation integrity testing is not necessary.

Features and Benefits• Upgrade existing equipment without replacing the valve • Simple conversion without breaking the body/bonnet seal • Remove personnel from the high pressure area • Introduce automation into your system • Position indication feedback • Torque output to highlight the need for upcoming valve maintenance • All major components are fully interchangeable with the manual • Version ( Body, Bonnet, Stem, Gate, etc) • Ultra reliable and low maintenance • Also available for Anson ™ Mud Valves

E-Type Gate Valves – Upgrade to Remote Actuation

Anson™ E-Type Gate Valves – Upgrade to Remote Actuation Convert your existing Anson™ E-Type Manual Gate Valve to electric actuation with our Electric Actuation Conversion Kit. The kit can be easily installed without breaking the pressure seal between the bonnet and body, meaning post installation integrity testing is not necessary.

Features and Benefits • Upgrade existing equipment without replacing the valve• Simple conversion without breaking the body/bonnet seal• Remove personnel from the high-pressure area• Introduce automation into your system• Position indication feedback• Torque output to highlight the need for upcoming valve maintenance• All major components are fully interchangeable with

the manual version (Body, Bonnet, Stem, Gate, etc)• Ultra-reliable and low maintenance• Also available for Anson™ Mud Valves

Mento ASKontinentalvegen 22, 4056 TanangerPhone: +47 48 11 03 00Mail: [email protected]

10

Our purpose-made Anson mud gate valves are suitable for the toughest demands of abrasive drilling mud service. We also provide piping for high pressure mud application and complete standpipe manifolds.

We offer two models of these easy-to-operate and simple-to-maintain valves—MV50 (suitable for up to 5,000-psi maximum working pressure) and MV75 (suitable for up to 7,500-psi maximum working pressure).

MV50: Suitable for a maximum working pressure of 5,000 PSI

• Available with various connections including butt weld, flange, hub, or hammer union • Molded, one-piece (boot) seat design particularly suited for abrasive service and applications where valve contamination by line fluid sediment is an issue • Nitride hardened stainless steel gate as standard

7. Mud Gate Valves

Mud valves

11


• Available with various connections including butt weld, flange, hub, or hammer union • One-piece, ‘disc type’ gate and seat design: • Suspended stainless steel discs molded with rubber, designed to dampen pulsation effect from mud pumps and extend the life of the valve • Repeatable high- and low-pressure sealing; capable of passing the most stringent testing for this type of valve in the industry. • Nitride hardened stainless steel gate as standard • Cavity-less body design limits ingress of contaminants • Highly qualified valve tested for repeatable low- and high-pressure sealing capability with both liquid and gas

We can now deliver mud valves with electric actuator or proximity switches

Mud valves

7. Mud Gate Valves

Mud valves

Our purpose-made Anson mud gate valves are suitable for the toughest demands of abrasive drilling mud service. We also provide piping for high pressure mud application and complete standpipe manifolds.

We offer two models of these easy-to-operate and simple-to-maintain valves—MV50 (suitable for up to 5,000-psi maximum working pressure) and MV75 (suitable for up to 7,500-psi maximum working pressure).


• Available with various connections including butt weld, flange, hub, or hammer union• Molded, one-piece (boot) seat design particularly suited for abrasive service and applications where valve contamination by line fluid sediment

is an issue

• Nitride hardened stainless steel gate as standard


• Available with various connections including butt weld, flange, hub, or hammer union• One-piece, ‘disc type’ gate and seat design:

• Suspended stainless steel discs molded with rubber, designed to dampen pulsation effect from mud pumps and extend the life of the valve

• Repeatable high- and low-pressure sealing; capable of passing the most stringent testing for this type of valve in the industry.

• Nitride hardened stainless steel gate as standard

• Cavity-less body design limits ingress of contaminants

• Highly qualified valve tested for repeatable low- and high-pressure sealing capability with both liquid and gas

We can now deliver mud valves with electric actuator or proximity switches

MV75: Solid disc design

MV75: Solid disc design

12

Fully customizable manifold assemblies for well service & control

Mento have considerable experience in the design and manufacture of manifolds used across several applications and often to a bespoke design. The manifolds can be comprised of Anson gate valves, plug valves, Master flo choke valves, as well as API studded blocks and hammer union fittings. We design and assemble all the major components used within our manifolds, giving us full control over the project from start to finish.

In addition to layout and design choices for manifolds, we also offer variations for the type of actuation to suit your requirements, either manual operation (handwheel) or choice of actuation, operated by a control system from a remote location. The most common manifolds that we produce is the standpipe and choke & kill manifold. These manifolds are used in several applications both onshore and offshore. They are an arrange-ment of shut off valves and choke valves, designed for controlling and reducing surface well pressure upstream of the process equipment. Two choke valves are incorporated within the assembly to allow the manifold to function at all times, even if service needs to performed on one of them.

All engineering and production is done in Mento`s facilities in Norway

• Diverter manifolds • Debris catcher manifolds • Choke and kill systems • Managed pressure drilling systems • Sand management systems • Process equipment • BOP arrangement • Standpipe manifolds • Cement manifolds

8. Design & Manufacture of Manifolds

Manifolds

138. Manifolds

Choke & kill manifold

A choke manifold is the primary means of control-ling surface well flow and pressure using a system of shutoff valves and choke valves. Dependent upon the application, the shut off valves would either be Anson plug valves or E-type gate valves and choke valves. Using a mix of adjustable (with handwheel/ actuated) or positive (fixed bean) choke valves, the manifold controls the flow rate and reduces well pressure ahead of downstream processing equip-ment.

The number of valves, configuration of the mani-fold, and choice of actuation are customizable. We work with you to ensure that the design is perfectly suited to your application.

Standpipe manifold

A mud standpipe manifold is installed downstream of the mud pumps with the purpose of diverting the flow of drilling fluids toward the drill line or drill string. Standpipe manifolds are designed and manufac-tured to suit customer requirements and are avail-able in working pressure up to 7500 psi. Construc-tion is available in weld end, flange end, hub end

or hammer union type. The manifold comprises of mud gate valves, forged manifold fittings, bleed off choke, pressure sensors and local pressure gauges. We use mud gate valves from Anson and choke valves from Master flo as standard. We work with you to ensure that the design is perfectly suited to your application.

Debris catcher manifold

The debris catcher (Junk catcher) manifold is used in flowback operations to protect downstream equip-ment from impact damage from large particles. The manifold is comprised of either Anson plug valves or e-type gate valves and an Mento design debris catcher. This can be single leg (one catcher) or dual leg (two catchers). The dual leg design enables zero downtime, as when one strainer line is being cleared the other strainer can be used.

The debris catcher contains a filter (screen) that catches and retains large solids. As part of the flowback system, the debris catcher manifold is positioned upstream of the choke manifold to protect the chokes and equipment downstream.

Mento`s debris catchers are available with fine mesh filters included with the screen to remove smaller particles from the process flow.

Mento design and manufacture manifolds to our own or customers’ designs. These manifolds are used for various applications and are made up of high end OEM valves , fittings & flowline

Manifolds

Fully customizable manifold assemblies for well service & controlWe have considerable experience in the design and manufacture of manifoldsused across several applications and often to a bespoke design. The manifolds can be comprised of Anson gate valves, plug valves, Master flo choke valves, as well as API studded blocks and hammer union fittings. We design and assemble all the major components used within our manifolds, giving us full control over the project from start to finish.

In addition to layout and design choices for manifolds, we also offer variations for the type of actuation to suit your requirements, either manual operation (handwheel) or choice of actuation, operated by a control system from a remote location. The most common manifolds that we produce is the standpipe and choke & kill manifold. These manifolds are used in several applications both onshore and offshore. They are an arrangement of shut off valves and choke valves, designed for controlling and reducing surface well pressure upstream of the process equipment. Two choke valves are incorporated within the assembly to allow the manifold to function at all times, even if service needs to performed on one of them.

Type of manifolds that we design & manufacture

• Diverter manifolds

• Debris catcher manifolds

• Choke and kill systems

• Managed press ure drilling systems

• Sand management systems

• Process equipment

• BOP arrangement

• Standpipe manifolds

• Cement manifolds

We design and manufacture manifolds to our own or customers’ designs. These manifolds are used for various applications and are made up of high end OEM valves , fittings & flowline

Choke & kill manifold A choke manifold is the primary means of controlling surface well flow and pressure using a system of shutoff valves and choke valves. Dependent upon the application, the shut off valves would either be Anson plug valves or E-type gate valves and choke valves. Using a mix of adjustable (with handwheel/ actuated) or positive (fixed bean) choke valves, the manifold controls the flow rate and reduces well pressure ahead of downstream processing equipment.

The number of valves, configuration of the manifold, and choice of actuation are customizable. We work with you to ensure that the design is perfectly suited to your application.

Standpipe manifold A mud standpipe manifold is installed downstream of the mud pumps with the purpose of diverting the flow of drilling fluids toward the drill line or drill string. Standpipe manifolds are designed and manufactured to suit customer requirements and are available in working pressure up to 7500 psi. Construction is available in weld end, flange end, hub end or hammer union type. The manifold comprises of mud gate valves, forged manifold fittings, bleed off choke, pressure sensors and local pressure gauges. We use mud gate valves from Anson and choke valves from Master flo as standard. We work with you to ensure that the design is perfectly suited to your application.

Debris catcher manifold The debris catcher (Junk catcher) manifold is used in flowback operations to protect downstream equipment from impact damage from large particles. The manifold is comprised of either Anson plug valves or e-type gate valves and an Mento design debris catcher. This can be single leg (one catcher) or dual leg (two catchers). The dual leg design enables zero downtime, as when one strainer line is being cleared the other strainer can be used.

The debris catcher contains a filter (screen) that catches and retains large solids. As part of the flowback system, the debris catcher manifold is positioned upstream of the choke manifold to protect the chokes and equipment downstream.

Mento`s debris catchers are available with fine mesh filters included with the screen to remove smaller particles from the process flow.

14

Regularly scheduled maintenance increases the reli-ability and longevity of your equipment in addition to reducing the total cost of ownership. Mento`s fully equipped facilities can accommodate all your service needs. As an added feature of our service and maintenance program, we offer long-term service and maintenance contracts. Re-certification means that a product is inspected and tested in accordance with the OEM specifications, third-party documentation, and with parts fitted that comply with the original specification and certification. We also have an online valve management system software to support our activities, where you as client can have your own log-in. We can perform the job either onshore in our workshop or offshore on rig/ platforms

Repairs, recertifications, and rebuilds

Our service shops provide turnkey engineering solutions to repair, update, or standardize your original designs. This ensures that you are receiving the technical knowledge and latest advances for your worn or cold-stacked equipment.

Training

To operate equipment at maximum performance and efficiency, we offer in-house, at-your-facility, or on-the-job training. Our structured educational programs are facilitated by industry experts calling on real-world experience and educating through actual scenarios. Our programs can be tailored to meet safety, maintenance, and operational perfor-mance per OEM standards.

Rental Equipment

We offer a broad range of rental equipment, including flowline, hoses and filtration systems.

Technical Support

Our support team is based in Bergen and available 24 hours a day, enabling an immediate response to client needs. Our support center help maximize the efficiency of our customers’ operations anytime and anywhere in the world. In addition, we have a dedicated professional engineering team to support our clients, which demonstrates our level of com-mitment to providing high-quality services.

9. Service & maintenance

Service & maintenance

1510. Spare parts

The Anson gate & mud valve range has been designed on a modular basis making numerous components interchangeable across sizes and pressure ratings.

The result of this has been to significantly reduce the cost of manufacture of both valves and spare parts. Substantial savings are made and passed on to the customer in the form of competitively priced valves and spare parts. We at Mento understand your need for minimizing costly downtime and have invested heavily in building up a complete stock of valves and spare parts locally in Norway. As your equipment moves into the field, we are standing by to support you with some of the best customer service in the industry. Our highly trained service technicians are available to help to keep your operations running smoothly.

Advice is freely given in the full knowledge that we at Mento can also benefit from an operator’s practical experience, as it is mainly from feedback from the end user that improvements can be made. Listening to what our customers have to say is and shall remain the cornerstone of our business.

Always use OEM parts to ensure that you get the best out of our equipment and the intended life of the product.

Spare parts

1610. Spare parts

P/N Valve Description Material description Bolts P/N Ring joint P/N

Seal kit P/N

Redress kit P/N

GA21605LXE3INCB10001

Anson GV 2.1/16"5K FLG ENDS E-TYPE MK2

Anson GV 2.1/16"5K FLG ENDS E-TYPE MK2 EE-360 L-X PSL3 CRA625 RTJ & SEAT PKTS 21th edition

L7G7SB2XN7/8"X155

R024RO6 72136 72135

GA29605LXE3INCB007


Anson GV 2.9/16" 5K FLG ENDS E-TYPE MK2 EE-360 L-X PSL3 CRA625 RTJ & SEAT PKTS 20th edition

L7G7SB2XN1"X165

R027RO6 N/A 73976


Anson GV 3.1/8" 5K FLG ENDS E-TYPE MK2


L7G7SB2XN11/8"X200

R035RO6 71699 71756

GA41605LXE3INCB007


Anson GV 4.1/16"5K FLG ENDS E-TYPE MK2 EE-360 L-X PSL3 CRA625 RTJ & SEAT PKT 20th edition

L7G7SB2XN11/4"X210

R039ROV6 N/A N/A



ANSON GV 2 1/16" 10K FLG ENDS E-TYPE MK2 EE-360 L-X PSL3 CRA625 RTJ & SEAT PKTS 21th edition

L7G7SB2XN3/4"X140

R152BX6 70907 70909




L7G7SB2XN7/8"X155

R153BX6 N/A 82880




L7G7SB2XN1"X180

R154BX6 70915 70916

GA41610LXE3INCB007



L7G7SB2XN11/8"X210

R155BX6




L7G7SB2XN7/8"X155

R152BX6 70907 70908




L7G7SB2XN1"X180

R153BX6 N/A 88272



Anson GV 3.1/16"15K FLG ENDS E-TYPE MK2 EE-360 L-X PSL3 CRA625 RTJ & SEAT PKT 21th edition

L7G7SB2XN11/8"X200

R154BX6 70913 70914

P/N Valve Description Material description Bolts P/N Ring joint P/N

Seal kit P/N

Redress kit P/N

A25593 Anson 3" X 3" Mud valve MV50, 5000PSI

Anson 3" Sch.XXS MV50, super trim MSL3 P-U, BW

TBA TBA N/A N/A

A75574-3 Anson 5" X 4" Mud valve MV50,

Anson 5"x4" Sch.XXS MV50, super trim MSL3 P-U, BW

TBA TBA N/A N/A

A88727-3 Anson 2" X 2" Mud valve MV75, 7500PSI

Anson 2" Sch. XXS MV75, Super trim, MSL3 P-U, BW

TBA TBA N/A N/A


Anson 2" X 3" Sch. XXS, Super trim, MSL3 P-U, BW

TBA TBA N/A N/A

A82205-3-001-00

Anson 3" X 3" Mud valve MV75, 7500PSI


TBA TBA N/A N/A

A82303-3 Anson 3" X 4" Mud valve MV75, 7500PSI

Anson 3" x 4" Sch. XXS, Super trim, MSL3 P-U, BW

TBA TBA N/A N/A



TBA TBA A77747 A77748

Gate valve specification• EE-360 Trim, • L-X temp range, • PSL 3, • Inconel ring grooves & seat pocket, • DNV OS-E101 Cat. 1 Certification

Mud valve specification• Super trim, • MSL3 • But weld ends • DNV OS-E101 Cat. 1 Certification

5 000 PSI

7 500 PSI

15 000 PSI

10 000 PSI

5 000 PSI

1711. API 6A Gate Valve specification

Mento only supplies the highest quality API 6A valves

They have been designed to be strictly in accordance with the following standards:MSS-SP75 Specifications for High test Wrought Butt Weld Fittings.ANSI B31.3 Chemical Plant and Petroleum Refinery Piping.ANSI 16.9 Factory made Wrought Steel Butt Weld Fittings.NACE MR-01-75 Sulphide Stress Cracking Resistant Metallic Materials for Oil Field Equipment.API 6A Specifications for Wellhead and Christmas Tree Equipment.

All API 6A equipment can be specified with the following: PSL level 1, 2, 3 or 4 Material Class, AA, BB, CC, DD, EE-NL PR-1 or PR-2 Temperature classes: K thru Y (-60degC to 345degC)

See the tables below for the dimensional data of standard Valve sizes. Please note that these are lists ofonly the most common sizes stocked. If you have any requirements for specific sizes or special materials that are not in the lists please contact us and we will be more than happy to assist. Mento are capable of supplying all API sizes.

API 6A Products

API 6A Products

Mento only supplies the highest quality API 6A Products including flanges and studded blocks . Flangesavailable are weld neck, target, blind & test blind.


All API 6A equipment can be specified with the following:PSL level 1, 2, 3 or 4Material Class, AA, BB, CC, DD, EE-NLPR-1 or PR-2Temperature classes: K thru Y (-60degC to 345degC)

See the tables below for the dimensional data of standard flange sizes. Please note that these are lists ofonly the most common sizes stocked. If you have any requirements for specific sizes or special materials that arenot in the lists please contact us and we will be more than happy to assist. Mento are capable of supplying allAPI sizes.

1812. Manual specification

API 6A Manual Gate ValveAPI 6A Manual Gate Valve

Table 1.1 API 6A Manual gate valve dimensions

Valve sizeAPI ring gasket

Bore diameter(A)

Face to face(B)

Centerline to base(C)

Extreme body diameter(D)

Centerline to handwheel(E)

Handwheeldia(F)

Turns to open

Weight(kGs)

2-1/16” 5K R-24 2.06” 14.62” 5.88” 7.25” 14.44” 12.00” 13,5 922-9/16” 5K R-27 2.56” 16.62” 6.50” 7.75” 15.38” 16.00” 15.5 1273-1/8” 5K R-35 3.12” 18.62” 7.88” 9.62” 16.25” 16.00” 18 1654-1/16” 5K R-39 4.06” 21.62” 10.12” 10.75” 17.88” 20.00” 24 2625-1/8” 5K R-44 5.12” 28.62” 13.00” 14.12” 24.12” 24.00” 23.5 6861-13/16” 10K BX-151 1.81” 18.25” 5.30” 8.25” 14.25” 16.00” 12 1152-1/16” 10K BX-152 2.06” 20.50” 5.75” 8.25” 14.44” 16.00” 13.5 1182-9/16” 10K BX-153 2.56” 22.25” 6.88” 9.25” 15.38” 16.00” 15.5 1503-1/16” 10K BX-154 3.06” 24.38” 8.06” 10.25” 16.25” 20.00” 18 2304-1/16” 10K BX-155 4.06” 26.38” 9.88” 12.25” 20.50” 24.00” 24 4165-1/8” 10K BX-169 5.12” 29.00” 13.00” 14.12” 24.12” 24.00” 23.5 6701-13/16” 15K BX-151 1.81” 18.00” 5.38” 8.25” 14.25” 16.00” 12 1272-1/16” 15K BX-152 2.06” 19.00” 6.12” 8.25” 14.44” 16.00” 14 1362-9/16” 15K BX-153 2.56” 25.00” 7.12” 10.25” 17.88” 20.00” 16 2073-1/16” 15K BX-154 3.06” 23.56” 9.00” 12.00” 19.00” 20.00” 19 3804-1/16” 15K BX-155 4.06” 29.00” 10.50” 13.00” 23.00” 24.00” 20 619

1913. Hydraulic Actuated specification

API 6A Hydraulic Gate ValveAPI 6A Hydraulic Gate Valve

Table 1.2 API 6A Hydraulic gate valve dimensions

Valve sizeAPI ring gasket

Bore diameter(A)

Face to face(B)


Extreme body diameter(D)

Centerline to top(E)

Actuator dia(F)

Weight(kGs)

2-1/16” 5K R-24 2.06” 14.62” 6.00” 7.25” 20.50” 7.87” 1103-1/8” 5K R-35 3.12” 18.62” 7.88” 9.62” 23.45” 7.87” 1834-1/16” 5K R-39 4.06” 21.62” 10.13” 10.75” 25.97” 7.87” 2805-1/8” 5K R-44 5.12” 28.62” 13.00” 14.12” 34.12” 11.25” 8052-1/16” 10K BX-152 2.06” 20.50” 5.75” 8.25” 20.50” 7.87” 1343-1/16” 10K BX-154 3.06” 24.38” 8.06” 10.25” 23.45” 7.87” 2504-1/16” 10K BX-155 4.06” 26.38” 10.50” 12.25” 29.78” 10.75” 4745-1/8” 10K BX-169 5.12” 29.00” 13.00” 14.12” 34.12” 11.25” 7892 1/16" 15K BX-152 2.06” 19.00" 6.12" - 20.50" - 1523 1/16" 15K BX-154 3.06” 23.56" 9.00" - 28.19" - 4364 1/16" 15K BX-155 4.06” 29.00" 10.50" - 33.56" - 736

2014. MV50 Mud Valve specification

5,000 Psi Mud Valves Butt Weld Ends5,000 Psi Mud Valves Butt Weld Ends

Table 1.3- 5,000 PSI BW Mud valve dimensions

Valve sizeBore diameter at

seat(A) End to end(B)Centerline to

base(C)Centerline to

top(D)Handwheel

dia(E) Weight2" x 2" sch XXS 2.00" 9.00" 2.88" 13.00" 14.00" 283" x 3" sch XXS 3.00" 11.00" 4.00" 18.00" 18.00" 644" x 4" sch XXS 4.00" 13.00" 5.12" 24.63" 23.00" 955" x 4" sch XXS 4.00" 13.00" 5.12" 24.63" 23.00" 100

5,000 PSI Mud Valves API 6A Flanged Ends5,000 PSI Mud Valves API 6A Flanged Ends

Table 1.5- 5,000 PSI API 6A Flanged Mud valve dimensions

Valve sizeAPI 6A

flange size RTJ typeEnd to end(A)


Centerline to top(D)

Handwheel dia(E) Flange dia(F)

Bore diameter at

seat(A) Weight2" 2-1/16” 5K R24/ RX24 12.12" 2.88" 13.00" 14.00" 8.50" 2.00" 503" 2-9/16” 5K R27/ RX27 20.00" 4.00" 18.00" 18.00" 9.62" 3.00" 984" 4-1/16” 5K R39/ RX39 18.00" 5.12" 24.63" 23.00" 12.25" 4.00" 1504" 4-1/16” 5K R39/ RX39 23.50" 5.12" 24.63" 23.00" 12.25" 4.00" 157End to end dimension can be modified acc. to customer requirements

21

5,000 PSI Mud Valves API 6A Flanged Ends


Valve sizeAPI 6A





Bore diameter at

seat(A) Weight2" 2-1/16” 5K R24/ RX24 12.12" 2.88" 13.00" 14.00" 8.50" 2.00" 503" 2-9/16” 5K R27/ RX27 20.00" 4.00" 18.00" 18.00" 9.62" 3.00" 984" 4-1/16” 5K R39/ RX39 18.00" 5.12" 24.63" 23.00" 12.25" 4.00" 1504" 4-1/16” 5K R39/ RX39 23.50" 5.12" 24.63" 23.00" 12.25" 4.00" 157End to end dimension can be modified acc. to customer requirements

15. MV75 Mud Valve specification

7,500 Psi Mud Valves Butt Weld Ends7,500 Psi Mud Valves Butt Weld Ends

Table 1.4- 7,500 PSI BW Mud valve dimensions

Valve sizeBore diameter at

seat(A) End to end(B)Centerline to

base(C)Centerline to

top(D)Handwheel

dia(E) Weight2" x 2" sch XXS 2.00” 14.00” 3.25” 11.88” 14.00” 543" x 3" sch XXS 3.00” 16.00” 4.88” 18.13” 18.00” 1104" x 3" sch XXS 3.00” 16.00” 4.88” 18.13” 18.00” 1105" x 4" sch XXS 4.00” 16.00” 5.12” 24.63” 23.00” 1606" x 5" sch XXS 5.00” 17.88” 5.75” 30.64” 26.00” 270

7,500 PSI Mud Valves API 6A Flanged Ends7,500 PSI Mud Valves API 6A Flanged Ends


Valve sizeAPI 6A





Bore diameter at

seat(A) Weight2” 2-1/16” 10K BX-152 13.50” 3.25” 11.88” 14.00” 7.88” 2.00” 70kg3” 2-9/16” 10K BX-153 22.25” 4.87” 18.13” 18.00” 9.12” 3.00” 155kg3” 3-1/16” 10K BX-154 27.12” 4.87” 18.13” 18.00” 10.62” 3.00” 162kg5” 4-1/16” 10K BX-155 29.12” 7.00” 24.63” 23.00” 12.44” 4.00” 250kg5” 5-1/8” 10K BX-169 29.00” 5.75” 30.64” 26.00” 14.06” 5.13” 375KgEnd to end dimension can be modified acc. to customer requirements

2216. Torque to Flange & Bonnets

Applying Torque to Flanges & Bonnets

Scope 1. This specification details the requirements for controlled bolting of API 6A Flange connections and Gate Valve Bonnets including methods that shall be used when applying controlled bolting to these connections.

2. Values stipulated in the enclosed tables 1 and 2 (Flange Connections) are extracted from values recommended in API 6A 19thedition

Application 3. This document shall be used as an internal procedure for assembly of the above connections for API 6A equipment.

4. If issued to end users of this equipment it may be used as a recommended practice.

Procedure 5. Prepare the connection for assembly, RTJ grooves and Bonnet seal areas should be clean and free from foreign matter.

6. API Flanges-Place a seal into one of the flanges and bring the two flanges together. Seals must be free of all grease. If the configuration of the connection is such that the seal may fall out of position during the mating of the two halves, the seal may be held in position using a thin stiff card that can be easily withdrawn once the two alves are together.

7. Gate Valve Bonnets-The recommended method is to install the seal onto the body seal area then lower the bonnet over the studs locating over the seal and body. Grease should NOT be applied to the seal or seal areas.

8. Place the required quantity of studs c/w nuts into the connection, threads and nut face should be lubricated during assembly, make up hand tight. (Ref. Lubrication Section).

9. Torque shall be applied to the connection using one of the following methods

• Torque wrench and socket.

• Calibrated hydraulic torque equipment.

10. The required final torque setting for the connection shall be obtained from table 1, table 2 for Flange connections and table 3 Bonnet Connections. Torque shall be applied to each nut on the connection in the sequence shown in fig 1 at 25% of this figure.

11. Torque shall then be applied at 50%, then 75% and final 100% of the required torque using the same sequence. As an aid to assembly each bolting position in the connection shall be numbered in this sequence.

Reccomended lubricant on the studding: Clare Autolube


Applying Torque to Flanges & BonnetsTightening Sequence

8 off

1

5

64

7 3

2 8

12 off

16 off

20 off 24 off

1

1611

4 6 139

2

5

1571214

10 83

3 711

1713

9 151 20

25

6191016

18124 148

8 24412 2017 15

21 1014 2

1 67 22

11 1819 13

23 916 35

110 12

5

4

8 2

6 711 93


Table 1 - Low Strength Studding (API Flanges)NOTE–Low strength studding is identified with an “M” designation after the material grade eg. A320 L7MA193 B7M

Table 2 - High Strength Studding (API Flanges)

* Column 3 and 4 - (f = 0.07) –Studs and Nuts coated with PTFE or similar coating. (f = 0.13) –Bare metal studs and nuts well lubricated with compound tested in accordance with ISO 13678

Table 1- Low Strength Studding (API Flanges)NOTE–Low strength studding is identified with an “M” designation after the material grade eg. A320 L7MA193 B7M

Bolt size Bolt Tension lbs.

Make Up Torque ft.lbf

( f =0.07)*

Make Up Torque

ft.lbf ( f =0.13)*

1/2”-13UNC 5,676 27 45

5/8”-11UNC 9,026 52 88

3/4”-10UNC 13,378 90 153

7/8”-9UNC 18,469 143 243

1”-8UNC 24,23 213 361

1.1/8”-8UN 31,618 305 523

1.1/4”-8UN 39,988 421 726

1.3/8”-8UN 49,34 563 976

1.1/2”-8UN 59,674 733 1,278

1.5/8”-8UN 70,989 934 1,635

1.3/4”-8UN 83,286 1,169 2,054

1.7/8” –8UN 95,565 1,44 2,539

2”–8UN 110,825 1,75 3,094

2.1/4”-8UN 142,292 2,496 4,436

2.1/2”–8UN 177,685 3,429 6,118

Table 2- High Strength Studding (API Flanges)

* Column 3 and 4 -(f = 0.07) –Studs and Nuts coated with PTFE or similar coating.(f = 0.13) –Bare metal studs and nuts well lubricated with compound tested in accordance with ISO 13678

Bolt size Bolt Tension lbs.Make Up Torque ft.lbf

( f =0.07)*Make Up Torque ft.lbf ( f =0.13)*

1/2”-13UNC 7,45 35 595/8”-11UNC 11,865 68 1153/4”-10UNC 17,559 118 2007/8”-9UNC 24,242 188 3191”-8UNC 31,802 279 4741.1/8”-8UN 41,499 401 6861.1/4”-8UN 52,484 553 9531.3/8”-8UN 64,759 739 1,2811.1/2”-8UN 78,322 962 1,6771.5/8”-8UN 93,173 1,226 2,1461.3/4”-8UN 109,313 1,534 2,6961.7/8”-8UN 126,741 1,89 3,3322”-8UN 145,458 2,297 4,0612.1/4”-8UN 186,758 3,276 5,8222.1/2”-8UN 233,212 4,5 8,030


Table 1 - Gate Valve Bonnet Torque – For High Strength Studding

NOTE–for A193.B7/A194.2H & A320.L7 / A194 Gr 7 Combinations only. Different values are required fromNACE controlled M designated studs and nuts. NOTE–for uncoated nuts only using f=0.08

Table 1- Gate Valve Bonnet Torque –For High StrengthStudding.

NOTE–for A193.B7/A194.2H & A320.L7 / A194 Gr 7 Combinations only. Different values are required from NACE controlled M designated studs and nuts.NOTE–for uncoated nuts only using f=0.08

Valve flange Valve bore Rating(PSI) Stud size No. Studs Torque1.13/16” 1.13/16” 10,000 7/8 9UNC 8 200“ “ 15,000 7/8 9UNC 8 3002.1/16” “ 3,000 7/8 9UNC 8 100“ “ 5,000 7/8 9UNC 8 150“ “ 10,000 7/8 9UNC 8 225“ “ 15,000 1" 8UN 8 3752.9/16” 2.9/16” 3,000 3/4" 10UNC 8 125“ “ 5,000 3/4" 10UNC 8 175“ “ 10,000 1" 8UN 8 325“ “ 15,000 1.1/8” 8UN 8 5503.1/8” 3.1/8” 2,000 3/4" 10UNC 8 100“ “ 3,000 3/4" 10UNC 8 125“ “ 5,000 7/8” 9UNC 8 2503.1/6” 3.1/16” 10,000 1.1/8” 8UN 8 450“ “ 15,000 1.3/8” 8UN 8 9504.1/16” 4.1/16” 3,000 1.1/8” 8UN 8 275“ “ 5,000 1.1/8” 8UN 8 450“ “ 10,000 1.3/8” 8UN 8 800“ “ 15,000 1.1/2” 8UN 12 11505.1/8” 5.1/8” 3,000 1.3/8” 8UN 8 500“ “ 5,000 1.3/8” 8UN 8 850“ “ 10,000 1.3/8” 8UN 8 1250“ “ 15,000 1.3/4” 8UN 12 18257.1/16” 6.3/8” 3,000 1.1/4” 8UN 12 375“ “ 5,000 1.1/4” 8UN 12 625“ “ 10,000 1.3/8” 8UN 12 1225“ “ 15,000 1.3/4” 8UN 16 2275“ 7.1/16” 5,000 1.3/8” 8UN 12 975“ “ 10,000 1.1/2” 8UN 12 1600“ “ 15,000 1.3/4” 8UN 16 2775NA 7.3/8” 10,000 1.1/2” 8UN 12 16009” 9” 3,000 1.1/4” 8UN 12 700

2617. Lubrication

Lubrication schedule

*The lubrication period should be considered as a minimum requirement under favourable operating conditions. Severe service may require a more frequent application of lubricant. In particular gate and plug valves being used on sandy or abrasive service or high flow rates will require more frequent application of body filler / sealant.

** Plug Valve sealant / grease will oxidise or become contaminated during normal use of the valve. Oldsealant cannot be totally displaced by re-injection. Valves must be dismantled and serviced to remove old sealant.

*** 17537 for API temp range P-X; 24104 for API range K-L

Lubrication schedule

*The lubrication period should be considered as a minimum requirement under favourable operating conditions. Severe service may require a more frequent application of lubricant. In particular gate and plug valves being used on sandy or abrasive service or high flow rates will require more frequent application of body filler / sealant.** Plug Valve sealant / grease will oxidise or become contaminated during normal use of the valve. Oldsealant cannot be totally displaced by re-injection. Valves must be dismantled and serviced to remove old sealant. *** 17537 for API temp range P-X; 24104 for API range K-L

Product type ComponentMaintenance

leaflet Lubricant p/nLubrication safety

leafletMethod of application

Lubrication period*

E-type Gate valve(Manual)

Body cavity

M27, M57

17537*** 24104***

PD106 PD168

Lubricate through grease fitting on

bonnet

Every 20-50 operation or

2 months

Bearing housing 45368# D0815#

Lubricate through grease fitting on bearing housing


2 months

Gear box 45368# D0815# Pack on assemblyDuring valve

overhaul

E-type Gate valve(Actuated) Body cavity M45, M49

17537*** 24104***

PD106 PD168


bonnet


2 months

Mud valve

Screw threads & bearings

M30, M31, M43, M46, M47 45368# D0815#


hub or screw housing


2 months

27

Mento only supplies the highest quality API 6A Products including flanges and studded blocks. Flanges available are weld neck, target, blind & test blind.


All API 6A equipment can be specified with the following: PSL level 1, 2, 3 or 4 Material Class, AA, BB, CC, DD, EE-NL PR-1 or PR-2 Temperature classes: K thru Y (-60degC to 345degC)

See the tables below for the dimensional data of standard flange sizes. Please note that these are lists ofonly the most common sizes stocked. If you have any requirements for specific sizes or special materials that are not in the lists please contact us and we will be more than happy to assist. Mento are capable of supplying all API sizes.

18. API 6A Valves & Manifolds

API 6A Products

API 6A Products

Mento only supplies the highest quality API 6A Products including flanges and studded blocks . Flangesavailable are weld neck, target, blind & test blind.


All API 6A equipment can be specified with the following:PSL level 1, 2, 3 or 4Material Class, AA, BB, CC, DD, EE-NLPR-1 or PR-2Temperature classes: K thru Y (-60degC to 345degC)

See the tables below for the dimensional data of standard flange sizes. Please note that these are lists ofonly the most common sizes stocked. If you have any requirements for specific sizes or special materials that arenot in the lists please contact us and we will be more than happy to assist. Mento are capable of supplying allAPI sizes.


Flanges and Studded Blocks are designed and manufactured in accordance with the following specifica-tions:-

API 6A Specification for Wellhead and Christmas Tree Equipment.ANSI B31.3 Chemical Plant and Petroleum Refinery Piping.ASME VIII Boiler and Pressure Vessel Code.MSS-SP-55 Quality Standards for Steel Castings for Valves, Flanges and Fittings and other Piping Components.NACE MR-01-75 Sulphide Stress Cracking Resistant Metallic Materials for Oilfield Equipment.

Flanges are available as Weld Neck, Integral, Blinds, Target & Test Blinds for use with the following pressure ratings:-

Section 1. API 6A TYPE 6B, 6BX Flanges and Studded Crosses and Tees

29

samt innledende tekst som på Word formatetMax Working pressure 5 000 PSI 10 000 PSI 15 000 PSI 20 000 PSITest pressure 7 500 PSI 15 000 PSI 22 500 PSI 30 000 PSIProduct specification levels 1, 2, 3 & 4 1, 2, 3 & 4 1, 2, 3 & 4 1, 2, 3 & 4API temperature rating

K(-60 deg. C) to Y(+345 deg. C)

K(-60 deg. C) to Y(+345 deg. C)

K(-60 deg. C) to Y(+345 deg. C)

K(-60 deg. C) to Y(+345 deg. C)

Min. Yield 60 000 PSI 60 000 PSI 75 000 PSI 75 000 PSIMin. Tensile 85 000 PSI 85 000 PSI 95 000 PSI 95 000 PSIMaterial API 60K API 60K API 75K API 75K


Nominal size and bore of flange(in)

Hub lenght/ Threaded line- pipe flange

Hub lenght/ Threaded casing flange

Hub lenght tubing flange

Hub lenght/ Welding Neck Line pipe flange

L1 L2 L3 L42 1⁄16 2.56 — 2.56 4.312 9⁄16 2.81 — 2.81 4.443 1⁄8 3.19 — 3.19 4.944 1⁄16 3.88 3.88 3.88 5.195 1⁄8 4.44 4.44 — 6.447 1⁄16 5.06 5.06 — 7.139 6.06 6.06 — 8.8111 6.69 6.69 — 10.44

Notes: Dimension are in inches

Nominal size and bore of flange(in) Maximum bore

Outside diameter of flange Tolerance

Maximum Chamfer

B D D C2 1/16 2.09 8.50 ±0.06 0.122 9⁄16 2.59 9.62 ±0.06 0.123 1⁄8 3.22 10.50 ±0.06 0.124 1⁄16 4.28 12.25 ±0.06 0.12

Type 6B flanges for 5000 PSI rated working pressureTable 1.2 Hub and bore dimensions

Intergral, blind, target blind & test flanges and studded blocks

Weld neck flanges

Table 1.1. Hub and bore dimensionsType 6B flanges for 5000 PSI rated working pressure


samt innledende tekst som på Word formatetMax Working pressure 5 000 PSI 10 000 PSI 15 000 PSI 20 000 PSITest pressure7 500 PSI 15 000 PSI 22 500 PSI 30 000 PSIProduct specification levels 1, 2, 3 & 4 1, 2, 3 & 4 1, 2, 3 & 4 1, 2, 3 & 4API temperature

K(-60 deg. C) to Y(+345

K(-60 deg. C) to Y(+345 deg. C)

K(-60 deg. C) to Y(+345

K(-60 deg. C) to Y(+345 deg. C)

Min. Yield 60 000 PSI 60 000 PSI 75 000 PSI 75 000 PSIMin. Tensile85 000 PSI 85 000 PSI 95 000 PSI 95 000 PSIMaterial API 60K API 60K API 75K API 75K

Min. Yield 45 000 PSI 60 000 PSI 75 000 PSI 75 000 PSIMin. Tensile70 000 PSI 85 000 PSI 95 000 PSI 95 000 PSIMaterial API 45K API 60K API 75K API 75K


Hub lenght/ Threaded line- pipe flange

Hub lenght/ Threaded casing flange

Hub lenght tubing flange

Hub lenght/ Welding Neck Line pipe flange

Neck dia/ Welding neck line pipe flange

Tolerance Maximum bore of welding neck flange

L1 L2 L3 L4 A A B2 1⁄16 2.56 — 2.56 4.31 2.38 +0.09/-0.031.722 9⁄16 2.81 — 2.81 4.44 2.88 +0.09/-0.032.163 1⁄8 3.19 — 3.19 4.94 3.50 +0.09/-0.032.654 1⁄16 3.88 3.88 3.88 5.19 4.50 +0.09/-0.033.475 1⁄8 4.44 4.44 — 6.44 5.56 +0.09/-0.034.347 1⁄16 5.06 5.06 — 7.13 6.63 +0.016/-0.035.229 6.06 6.06 — 8.81 8.63 +0.016/-0.036.8411 6.69 6.69 — 10.44 10.75 +0.016/-0.038.53

Notes: Dimension are in inches

Intergral, blind, target blind & test flanges and studded

Weld neck flanges

Table 1.1. Hub and bore dimensionsType 6B flanges for 5000 PSI rated working pressure



Maximum bore

Outside diameter of flange

Tolerance Maximum Chamfer

Diameter of Raised face

Total thickness of flange

Basic thickness of flange

Diameter of hub

Diameter of bolt circle

Number of bolts

Diameter of bolts

Diameter of bolt holes

Bolt hole tolerance(see note)

Lenght of stud bolts

Ring number, R or RX

B D D C F T G A P2 1/16 2.09 8.50 ±0.06 0.12 4.88 1.81 1.50 4.12 6.50 8 7⁄8 1.00 +.06 6.00 242 9⁄16 2.59 9.62 ±0.06 0.12 5.38 1.94 1.62 4.88 7.50 8 1 1.12 +.06 6.50 273 1⁄8 3.22 10.50 ±0.06 0.12 6.62 2.19 1.88 5.25 8.00 8 1 1⁄8 1.25 +.06 7.25 354 1⁄16 4.28 12.25 ±0.06 0.12 7.62 2.44 2.12 6.38 9.50 8 1 1/4 1.38 +.06 8.00 395 1⁄8 5.16 14.75 ±0.06 0.12 9.00 3.19 2.88 7.75 11.50 8 1 1/2 1.62 +.06 10.00 447 1⁄16 7.16 15.50 ±0.12 0.25 9.75 3.62 3.25 9.00 12.50 12 1 3⁄8 1.50 +.06 10.75 469 9.03 19.00 ±0.12 0.25 12.50 4.06 3.62 11.50 15.50 12 1 5⁄8 1.75 +.09 12.00 5011 11.03 23.00 ±0.12 0.25 14.63 4.69 4.25 14.50 19.00 12 1 7⁄8 2.00 +.09 13.75 54

Notes: Dimension are in inchesMinimum bolt hole tolerance is -0.02"


Maximum bore





Large diameter of hub

Small diameter of hub

Lenght of hub

Radius of hub


number of bolts

Diameter of bolts





B D D C F T A E L R P

1 13⁄16 1.84 7.38 ±0.06 0.12 4.12 1.66 3.50 2.56 1.91 0.38 5.75 8 3/4 .88 +.06 5.00 1512 1⁄16 2.09 7.88 ±0.06 0.12 4.38 1.73 3.94 2.94 2.03 0.38 6.25 8 3/4 .88 +.06 5.25 1522 9⁄16 2.59 9.12 ±0.06 0.12 5.19 2.02 4.75 3.62 2.25 0.38 7.25 8 7⁄8 1.00 +.06 6.00 1533 1⁄16 3.09 10.62 ±0.06 0.12 6.00 2.30 5.59 4.34 2.50 0.38 8.50 8 1 1.12 +.06 6.75 1544 1⁄16 4.09 12.44 ±0.06 0.12 7.28 2.77 7.19 5.75 2.88 0.38 10.19 8 1 1⁄8 1.25 +.06 8.00 1555 1⁄8 5.16 14.06 ±0.06 0.12 8.69 3.13 8.81 7.19 3.19 0.38 11.81 12 1 1⁄8 1.25 +.06 8.75 1697 1⁄16 7.09 18.88 ±0.12 0.25 11.88 4.06 11.88 10.00 3.75 0.62 15.88 12 1 1/2 1.62 +.09 11.25 1569 9.03 21.75 ±0.12 0.25 14.12 4.88 14.75 12.88 3.69 0.62 18.75 16 1 1/2 1.62 +.09 13.00 15711 11.03 25.75 ±0.12 0.25 16.88 5.56 17.75 15.75 4.06 0.62 22.25 16 1 3/4 1.88 +.09 15.00 158

1 13⁄16 1.84 8.19 ±0.06 0.12 4.19 1.78 3.84 2.81 1.88 0.38 6.31 8 7⁄8 1.00 +.06 5.50 1512 1⁄16 2.09 8.75 ±0.06 0.12 4.50 2.00 4.38 3.25 2.12 0.38 6.88 8 7⁄8 1.00 +.06 6.00 1522 9⁄16 2.59 10.00 ±0.06 0.12 5.25 2.25 5.06 3.94 2.25 0.38 7.88 8 1 1.12 +.06 6.75 1533 1⁄16 3.09 11.31 ±0.06 0.12 6.06 2.53 6.06 4.81 2.50 0.38 9.06 8 1 1⁄8 1.25 +.06 7.50 1544 1⁄16 4.09 14.19 ±0.06 0.12 7.62 3.09 7.69 6.25 2.88 0.38 11.44 8 1 3⁄8 1.50 +.06 9.25 1555 1⁄8 5.16 16.50 ±0.06 0.12 8.88 3.88 9.62 7.88 3.22 0.62 13.50 12 1 1/2 1.62 +.09 11.50 169

15 000 PSI


Type 6BX Welding neck flanges for 10 000 & 15 000 PSI rated working pressureTable 1. 3 Hub and flange dimensions

10 000 PSI


Maximum bore





Basic thickness of flange

Diameter of hub


Number of bolts

Diameter of bolts





B D D C F T G A P2 1/16 2.09 8.50 ±0.06 0.12 4.88 1.81 1.50 4.12 6.50 8 7⁄8 1.00 +.06 6.00 242 9⁄16 2.59 9.62 ±0.06 0.12 5.38 1.94 1.62 4.88 7.50 8 1 1.12 +.06 6.50 273 1⁄8 3.22 10.50 ±0.06 0.12 6.62 2.19 1.88 5.25 8.00 8 1 1⁄8 1.25 +.06 7.25 354 1⁄16 4.28 12.25 ±0.06 0.12 7.62 2.44 2.12 6.38 9.50 8 1 1/4 1.38 +.06 8.00 395 1⁄8 5.16 14.75 ±0.06 0.12 9.00 3.19 2.88 7.75 11.50 8 1 1/2 1.62 +.06 10.00 447 1⁄16 7.16 15.50 ±0.12 0.25 9.75 3.62 3.25 9.00 12.50 12 1 3⁄8 1.50 +.06 10.75 469 9.03 19.00 ±0.12 0.25 12.50 4.06 3.62 11.50 15.50 12 1 5⁄8 1.75 +.09 12.00 5011 11.03 23.00 ±0.12 0.25 14.63 4.69 4.25 14.50 19.00 12 1 7⁄8 2.00 +.09 13.75 54

Notes: Dimension are in inchesMinimum bolt hole tolerance is -0.02"


Maximum bore





Large diameter of hub

Small diameter of hub

Lenght of hub

Radius of hub


number of bolts

Diameter of bolts





B D D C F T A E L R P

1 13⁄16 1.84 7.38 ±0.06 0.12 4.12 1.66 3.50 2.56 1.91 0.38 5.75 8 3/4 .88 +.06 5.00 1512 1⁄16 2.09 7.88 ±0.06 0.12 4.38 1.73 3.94 2.94 2.03 0.38 6.25 8 3/4 .88 +.06 5.25 1522 9⁄16 2.59 9.12 ±0.06 0.12 5.19 2.02 4.75 3.62 2.25 0.38 7.25 8 7⁄8 1.00 +.06 6.00 1533 1⁄16 3.09 10.62 ±0.06 0.12 6.00 2.30 5.59 4.34 2.50 0.38 8.50 8 1 1.12 +.06 6.75 1544 1⁄16 4.09 12.44 ±0.06 0.12 7.28 2.77 7.19 5.75 2.88 0.38 10.19 8 1 1⁄8 1.25 +.06 8.00 1555 1⁄8 5.16 14.06 ±0.06 0.12 8.69 3.13 8.81 7.19 3.19 0.38 11.81 12 1 1⁄8 1.25 +.06 8.75 1697 1⁄16 7.09 18.88 ±0.12 0.25 11.88 4.06 11.88 10.00 3.75 0.62 15.88 12 1 1/2 1.62 +.09 11.25 1569 9.03 21.75 ±0.12 0.25 14.12 4.88 14.75 12.88 3.69 0.62 18.75 16 1 1/2 1.62 +.09 13.00 15711 11.03 25.75 ±0.12 0.25 16.88 5.56 17.75 15.75 4.06 0.62 22.25 16 1 3/4 1.88 +.09 15.00 158

1 13⁄16 1.84 8.19 ±0.06 0.12 4.19 1.78 3.84 2.81 1.88 0.38 6.31 8 7⁄8 1.00 +.06 5.50 1512 1⁄16 2.09 8.75 ±0.06 0.12 4.50 2.00 4.38 3.25 2.12 0.38 6.88 8 7⁄8 1.00 +.06 6.00 1522 9⁄16 2.59 10.00 ±0.06 0.12 5.25 2.25 5.06 3.94 2.25 0.38 7.88 8 1 1.12 +.06 6.75 1533 1⁄16 3.09 11.31 ±0.06 0.12 6.06 2.53 6.06 4.81 2.50 0.38 9.06 8 1 1⁄8 1.25 +.06 7.50 1544 1⁄16 4.09 14.19 ±0.06 0.12 7.62 3.09 7.69 6.25 2.88 0.38 11.44 8 1 3⁄8 1.50 +.06 9.25 1555 1⁄8 5.16 16.50 ±0.06 0.12 8.88 3.88 9.62 7.88 3.22 0.62 13.50 12 1 1/2 1.62 +.09 11.50 169

15 000 PSI


Type 6BX Welding neck flanges for 10 000 & 15 000 PSI rated working pressureTable 1. 3 Hub and flange dimensions

10 000 PSI

31

Vertical B1 Vertical B2(Inches)+ .03,-0

(Inches)+ .03,-0

(Inches)+ .03,-0

(Inches)+ .03,-0

2 1⁄16 2 1⁄16 4.50 4.502 9⁄16 2 1⁄16 4.50 5.002 9⁄16 2 9⁄16 5.00 5.003 1⁄8 2 1⁄16 4.50 5.503 1⁄8 2 9⁄16 5.50 5.503 1⁄8 3 1⁄8 5.50 5.504 1⁄16 2 1⁄16 4.50 6.504 1⁄16 2 9⁄16 5.00 6.504 1⁄16 3 1⁄8 5.50 6.504 1⁄16 4 1⁄16 6.50 6.501 13⁄16 1 13⁄16 4.38 4.382 1⁄16 1 13⁄16 4.38 4.382 1⁄16 2 1⁄16 4.38 4.382 9⁄16 1 13⁄16 4.50 5.122 9⁄16 2 1⁄16 4.50 5.122 9⁄16 2 9⁄16 5.12 5.123 1⁄16 1 13⁄16 4.50 5.883 1⁄16 2 1⁄16 4.50 5.883 1⁄16 2 9⁄16 5.12 5.883 1⁄16 3 1⁄16 5.88 5.884 1⁄16 1 13⁄16 4.50 6.884 1⁄16 2 9⁄16 4.50 6.884 1⁄16 2 9⁄16 5.12 6.884 1⁄16 3 1⁄16 5.88 6.884 1⁄16 4 1⁄16 6.88 6.881 13⁄16 1 13⁄16 5.00 5.002 1⁄16 1 13⁄16 5.00 5.002 1⁄16 2 1⁄16 5.00 5.002 9⁄16 1 13⁄16 5.50 5.502 9⁄16 2 1⁄16 5.50 5.502 9⁄16 2 9⁄16 5.50 5.503 1⁄16 1 13⁄16 6.31 6.313 1⁄16 2 1⁄16 6.31 6.313 1⁄16 2 9⁄16 6.31 6.313 1⁄16 3 1⁄16 6.31 6.314 1⁄16 1 13⁄16 7.62 7.624 1⁄16 2 1⁄16 7.62 7.624 1⁄16 2 9⁄16 7.62 7.624 1⁄16 3 1⁄16 7.62 7.624 1⁄16 4 1⁄16 7.62 7.62

15 000

Table 1.4 studded crosses

Working pressure

Nominal size and bore Centre to face.

Centre to face.

5000

10 000



Hammer Lug Unions are designed and manufactured in accordance with the following specifications:-

API 6A Specification for Wellhead and Christmas Tree Equipment.API RP-14E Recommended Practice for Design and Installation of Offshore Production Platform PipingNACE MR-01-75 Sulphide Stress Cracking Resistant Metallic Materials for Oilfield Equipment.ASME VIII Boiler and Pressure Vessel Code.ANSI B31.3 Chemical Plant and Petroleum Refinery Piping.

Hammer Lug Unions are available in a range of figure numbers for use with the following pressure ratings and services:-

Section 2. Hammer Lug Unions


Fig 1002 Hammer Lug Union – 10,000 psi cwp (690 bar) 1” to 4” – 7,500 psi cwp (483 bar) 5” and 6”

Mento Hoses and Couplings Catalogue 287

Fig 1002– 10,000 psi cwp (690 bar) 1” to 4” – 7,500 psi cwp (483 bar) 5” and 6”

HUTE 1002 Threaded End – Blue Subs, Red Nut –

10,000 psi cwp

Size 1" 1.1/2" 2" 3" 4"

Union Complete

Part No. 102101 102151 102201 102301 102401

Weight (lb) 4,00 9,00 13,00 22,00 32,00

Nut

Part No. 102102 102152 102202 102302 102402

Weight (lb) 4,00 9,00 13,00 22,00 32,00

Male Sub

Part No. 102103 102153 102203 102303 102403

Weight (lb) 2,00 4,00 7,00 10,00 13,00

Female sub

Part No. 102104 102154 102204 102304 102404

Weight (lb) 1,00 3,00 3,00 7,00 10,00

Seal Ring

Part No. 102105 102155 102205 102305 102405

Weight (lb) 0,02 0,10 0,10 0,16 0,22

HUBL SG-1002

Blind Subs Sour Gas – Sour Gas Green

1”– 4” = 7,500 psi cwp, 5” & 6” = 5,000 psi cwp

Size 1" 2" 3" 4" 5" 6"

Male

Part No. SGBL102103 SGBL102203 SGBL102303 SGBL102403 SGBL102503 SGBL102603

Weight (lb) 2,00 3,00 7,00 10,00 30,00 40,00

Female

Part No. SGBL102104 SGBL102204 SGBL102304 SGBL102404 SGBL102504 SGBL102604

Weight (lb) 2,00 3,00 8,00 11,00 30,00 35,00

16 Anson Hammer Lug Unions

HUBWSG-1XX2 Butt Weld Sour Gas - XXS – Sour Gas Green –1" – 4" = 7,500 psi cwp, 5" & 6" = 5,000 psi cwpSize 1" 3" 4" 5" 6"

Union CompletePart No. SGBW102101XXS SGBW102301XXS SGBW102401XXS SGBW102501XXS SGBW102601XXSWeight (lb) 5,00 22,00 33,00 57,00 81,00NutPart No. SG102102 SG102302 SG102402 SG102502 SG102602Weight (lb) 2,00 10,00 13,00 26,00 37,00Male SubPart No. SGBW102103XXS SGBW102303XXS SGBW102403XXS SGBW102503XXS SGBW102603XXSWeight (lb) 1,00 6,00 10,00 15,00 20,00Female SubPart No. SGBW102104XXS SGBW102304XXS SGBW102404XXS SGBW102504XXS SGBW102604XXSWeight (lb) 1,00 7,00 10,00 16,00 23,00Seal RingPart No. 152106 152306 152406 152506 152606Weight (lb) 0,02 0,16 0,22 0,15 0,15

HUBW 1XX2 Butt Weld - XXS – Red Nut – 1" to 4" = 10,000 psi cwp, 5" & 6" = 7,500 psi cwpSize 1" 3" 4" 5" 6"

Union CompletePart No. BW102101XXS BW102301XXS BW102401XXS BW102501XXS BW102601XXSWeight (lb) 5,00 22,00 33,00 57,00 81,00NutPart No.

See threaded Fig. 1002 for nut part numbers and weights.SG102502 SG102602

Weight (lb) 26,00 37,00Male SubPart No. BW102103XXS BW102303XXS BW102403XXS BW102503XXS BW102603XXSWeight (lb) 1,00 6,00 10,00 15,00 20,00Female SubPart No. BW102104XXS BW102304XXS BW102404XXS BW102504XXS BW102604XXSWeight (lb) 1,00 7,00 10,00 16,00 23,00Seal RingPart No. 152105 152305 152405 207405 152605Weight (lb) 0,02 0,16 0,22 0,15 0,15


Fig 1502 Hammer Lug Union – 15,000 psi cwp (1034 bar)

HUBWSG-15XX2 Butt Weld Sour Gas XXS Sour Gas Green 10,000 psi cwpSize 1" 2" 3" 4"

Union CompletePart No. SGBW152101XXS SGBW152201XXS SGBW152301XXS SGBW152401XXSWeight (lb) 9,50 13,00 34,00

NutPart No.

See Threaded Fig. 1502 for nut part numbers and Weights.SG152402

Weight (lb) 17,00

Male SubPart No. SGBW152103XXS SGBW152203XXS SGBW152303XXS SGBW152403XXSWeight (lb) 0,80 2,50 3,30 9,20

Female SubPart No. SGBW152104XXS SGBW152204XXS SGBW152304XXS SGBW152404XXSWeight (lb) 1,00 2,50 3,20 7,80

Seal RingPart No. 152106 152206 152306 152406Weight (lb) 0,02 0,10 0,16 0,22

HUBW - 15XX2 Butt Weld XXS Blue Nut 15,000 psi cwpSize 1" 2" 3" 4"

Union CompletePart No. BW152101XXS BW152201XXS BW152301XXS BW152401XXSWeight (lb) 8,00 22,00 29,00 75,00

NutPart No.

See threaded Fig. 1502 for nut part numbers152402

Weight (lb) 36,00

Male SubPart No. BW152103XXS BW152203XXS BW152303XXS BW152403XXSWeight (lb) 2,00 7,00 9,00 21,00

Female SubPart No. BW152104XXS BW152204XXS BW152304XXS BW152404XXSWeight (lb) 2,00 6,00 8,00 17,00

Seal RingPart No. 152105 152205 152305 152405Weight (lb) 0,02 0,10 0,16 0,25


Fig 1502 – 15,000 psi cwp (1034 bar)

HUTE 1502

Threaded End

Red Subs, Blue Nut

1" to 3" = 15,000 psi cwp

Size 1" 2" 3"

Union Complete

Part No. 152101 152201 152301

Weight (lb) 3,80 19,00 30,00

Nut

Part No. 152102 152202 152302

Weight (lb) 1,90 9,00 12,00

Male

Part No. 152103 152203 152303

Weight (lb) 0,80 5,00 9,00

Female Sub

Part No. 152104 152204 152304

Weight (lb) 1,10 5,00 9,00

Seal Ring

Part No. 152105 152205 152305

Weight (lb) 0,02 0,10 0,16

Line Pipe Threaded Butt Weld Sch XXS

Size Weight Nut Total Body Total WeightInch lbs Radius Length Dia Length (lbs)

A B C B

1” 8.4 2.70” 4.36” 2.17” 4.36” 8.2

1.1/2” 16.4 3.63” 5.38” 2.97” 5.39” 16.5

2” 18.5 3.75” 7.04” 3.22” 6.17” 21.0

3” 31.0 4.57” 7.63” 4.50” 5.25” 28.5

4” 6.00” 8.50” 75.0

5” 6.50” 9.00” 95.0

6” 7.25” 9.75” 145.0

Note: Max bore size of 5” Butt Weld is 4” and for the 6” Butt Weld itis 5”.When enquiring about these sizes of union please specify wall thick-ness required.Where dimensions and weight are critical please consult the factory.Sch. XXS weights and lengths are shown for illustrative and weightpurposes only.

HUTE - SG1502

Threaded Ends Sour Gas Green 10,000 psi cwp

Size 2" 3"

Union Complete

Part No. SG152201 SG152301

Weight (lb) 19,00 30,00

Nut

Part No. SG152202 SG152302

Weight (lb) 9,00 12,00

Male Sub

Part NO. SG152203 SG152303

Weight (lb) 5,00 9,00

Female Sub

Part No. SG152204 SG152304

Weight (lb) 5,00 9,00

Seal Ring

Part No. 152206 152306

Weight (lb) 0,10 0,16



Fig 2202 Hammer Lug Union – 15,000 psi cwp (1034 bar)


Fig 2202 – 15,000 psi cwp (1034 bar)

HUBW - 15XX2Butt Weld XXS Blue Nut 15,000 psi cwp

Size 1" 2" 3" 4"

Union Complete

Part No. BW152101XXS BW152201XXS BW152301XXS BW152401XXS

Weight (lb) 8,00 22,00 29,00 75,00

Nut

Part No. See threaded Fig. 1502 for nut part numbers 152402

Weight (lb) 36,00

Male Sub


Weight (lb) 2,00 7,00 9,00 21,00

Female Sub


Weight (lb) 2,00 6,00 8,00 17,00

Seal Ring

Part No. 152105 152205 152305 152405

Weight (lb) 0,02 0,10 0,16 0,25

Butt Weld (Threaded not available) Weld Prep

Size Weight Nut TotalInch lbs Radius Length

A B O.D. I.D.

2” 23.0 3.75” 7.40” 2.50” 1.25”

3” 48.0 4.88” 9.56” 4.125” 2.06”

4” 76.0 6.00” 8.5” 5.50” 3.00”

5” 110.0 6.50” 10.75” 6.12” 4.00”

6” 170.0 7.25” 13.00” 7.75” 5.00”

Note: Weight indicated is for the weld prep shown. Differing O.D.and I.D. prepes can be supplied upon request.

Anson 3” and 4” unions are sometimes referred to as 2.1/2” and3” respectively by other manufacturers. If in doubt please do nothesitate to ask.

The Figure 2202 Sour Gas Union is ruggedly

proportioned and manufactured to the

highest quality standards to ensure safety

and reliability in service. Lip type elastomer

seals with stainless steel anti-extrusion

rings are fitted as standard. All H2S Service

Unions manufactured by Anson are

subjected to vigorous examination to

ensure the latest requirements of N.A.C.E.

are adhered to and the product is fit for

purpose.


Fig 1502 – 15,000 psi cwp (1034 bar)

The Figure 2202 Sour Gas Union is ruggedly proportioned and manufactured to the highest quality standards to ensure safety and reliability in service. Lip type elastomer seals with stainless steel anti-extrusion rings are fitted as standard. All H2S Service Unions manufactured by Anson are subjected to vigorous examination to ensure the latest requirements of N.A.C.E. are adhered to and the product is fit for purpose.


Fig 2202 – 15,000 psi cwp (1034 bar)

HUBW - 15XX2Butt Weld XXS Blue Nut 15,000 psi cwp

Size 1" 2" 3" 4"

Union Complete


Weight (lb) 8,00 22,00 29,00 75,00

Nut

Part No. See threaded Fig. 1502 for nut part numbers 152402

Weight (lb) 36,00

Male Sub


Weight (lb) 2,00 7,00 9,00 21,00

Female Sub


Weight (lb) 2,00 6,00 8,00 17,00

Seal Ring

Part No. 152105 152205 152305 152405

Weight (lb) 0,02 0,10 0,16 0,25

Butt Weld (Threaded not available) Weld Prep

Size Weight Nut TotalInch lbs Radius Length

A B O.D. I.D.

2” 23.0 3.75” 7.40” 2.50” 1.25”

3” 48.0 4.88” 9.56” 4.125” 2.06”

4” 76.0 6.00” 8.5” 5.50” 3.00”

5” 110.0 6.50” 10.75” 6.12” 4.00”

6” 170.0 7.25” 13.00” 7.75” 5.00”

Note: Weight indicated is for the weld prep shown. Differing O.D.and I.D. prepes can be supplied upon request.

Anson 3” and 4” unions are sometimes referred to as 2.1/2” and3” respectively by other manufacturers. If in doubt please do nothesitate to ask.

The Figure 2202 Sour Gas Union is ruggedly

proportioned and manufactured to the

highest quality standards to ensure safety

and reliability in service. Lip type elastomer

seals with stainless steel anti-extrusion

rings are fitted as standard. All H2S Service

Unions manufactured by Anson are

subjected to vigorous examination to

ensure the latest requirements of N.A.C.E.

are adhered to and the product is fit for

purpose.


Fig 1502 – 15,000 psi cwp (1034 bar)

Butt Weld (Thread not available) Weld PrepSize Inch

Weight lbs

Nut Radius A

Total Length B O.D. I.D.

2” 23.0 3.75” 7.40” 2.50” 1.25”3” * 48.0 4.88” 9.56” 4.125” 2.06”4” * 76.0 6.00” 8.50” 5.50” 3.00”5” 110.0 6.50” 10.75” 6.12” 4.00”6” 170.0 7.25” 13.00” 7.25” 5.00”Note: Weight indicated is for the weld prep shown. Differing O.D. and I.D. prepes can be supplied upon request. Anson* 3” and 4” unions are sometimes referred to as 2.1/2” and 3” respectively by other manufacturers. If in doubt please do not hesitate to ask.

HUBW - 2202 Butt Weld Sour Gas Sour Gas Green Nut 15,000 psi cwp (1034 bar)

HUBW - 2202 Blind Subs – Sour Gas Green – 15,000 psi cwp

Size 2" (1.25" I.D.) 3" (2.1/16" I.D.) 4" (3" I.D.) 2" 3" 4"

Union CompletePart No. SGBW222201 SGBW222301 SGBW222401Weight (lb) 23,10 47,74 75,90

NutPart No. SG222202 SG222302 SG222402Weight (lb) 12,32 19,80 37,40

Male SubPart No. SGBW222203 SGBW222303 SGBW222403 SGBL222203 SGBL222303 SGBL21689Weight (lb) 4,40 15,84 20,90 6,00 21,00 30,00

Female SubPart No. SGBW222204 SGBW222304 SGBW222404 SGBL222204 SGBL222304 SGBL16679Weight (lb) 5,50 11,44 17,60 7,00 15,00 27,00

Seal RingPart No. 222206 222306 222406Weight (lb) 0,10 0,12 0,17

Segment (Set 3)Part No. 222207 222307 222407Weight (lb) 0,90 1,30 2,60

Ret RingPart No. 222208 222308 222408Weight (lb) 0,01 0,01 0,02


Forged Long Sweep Manifold Fittings are designed and manufactured in accordance with the following specifications:-

MSS-SP-75 Specifications for High Test Wrought Butt Weld Fittings.ANSI B31.3 Chemical Plant and Petroleum Refinery Piping.ASME B16.9 Factory-Made Wrought Steel Buttwelding Fittings.ASME VIII Boiler and Pressure Vessel Code.API 6A Specification for Wellhead and Christmas Tree Equipment.NACE MR-01-75 Sulphide Stress Cracking Resistant Metallic Materials for Oilfield Equipment.

Manifold Fittings are available either Full Flow or with reducing configuration in all pipe wall schedules, for the following pressure ratings:-

Section 3. Long Sweep, 3D Double Back Reinforced & Full Flow


samt innledende tekst som på Word formatet

Max working pressure 5 000 PSI 7 500 PSI 10 000 PSI 15 000 PSITest pressure 7 500 PSI 11 250 PSI 15 000 PSI 22 500 PSIOperating temp. range

-60 TO +345 deg. C

-60 TO +345 deg. C

-60 TO +345 deg. C

-60 TO +345 deg. C

Min. Yield 52 000 PSI >80,000 PSI >80,000 PSI >80,000 PSIMin. Tensile 66 000 PSI 105 000 PSI 105 000 PSI 105 000 PSI

Material MSS-SP-75 Gr WPHY 52

ASTM A234 Gr 4130

ASTM A234 Gr 4131

ASTM A234 Gr 4132

D A B R2˝ 60.3 406 203 150 323˝ 88.9 406 203 150 484˝ 114.3 560 280 210 945˝ 141.3 610 305 240 1386˝ 168.3 762 381 305 208

D A B R2˝ 60.3 406 203 150 393˝ 88.9 406 203 150 334˝ 114.3 560 280 210 645˝ 141.3 610 305 240 906˝ 168.3 762 381 305 143

D A B R2˝ 60.3 330 203 150 343˝ 88.9 330 203 150 284˝ 114.3 406 280 210 515˝ 141.3 483 305 240 766˝ 168.3 686 381 305 132

Table 3.1 full flow cross

Table 3.2 full tee

Table 3.3 long sweep tee

Size All dimensions in mm Weight approx(kg)



samt innledende tekst som på Word formatetMax working 5 000 PSI7 500 PSI10 000 PSI15 000 PSITest pressure7 500 PSI11 250 PSI15 000 PSI22 500 PSIOperating temp.

-60 TO +345 deg. C

-60 TO +345

-60 TO +345

-60 TO +345

Min. Yield52 000 PSI>80,000 PSI>80,000 PSI>80,000 PSIMin. Tensile66 000 PSI105 000 PSI105 000 PSI105 000 PSI

Material

MSS-SP-75 Gr WPHY

ASTM A234 Gr

ASTM A234 Gr

ASTM A234 Gr

D A B R2˝ 60.3 406 203 150 323˝ 88.9 406 203 150 484˝ 114.3 560 280 210 945˝ 141.3 610 305 240 1386˝ 168.3 762 381 305 208

D A B R2˝ 60.3 406 203 150 393˝ 88.9 406 203 150 334˝ 114.3 560 280 210 645˝ 141.3 610 305 240 906˝ 168.3 762 381 305 143

D A B R2˝ 60.3 330 203 150 343˝ 88.9 330 203 150 284˝ 114.3 406 280 210 515˝ 141.3 483 305 240 766˝ 168.3 686 381 305 132

Table 3.1 full flow cross

Table 3.2 full tee

Table 3.3 long sweep tee





D A B R2˝ 60.3 365 115 265 393˝ 88.9 365 115 265 324˝ 114.3 510 155 365 655˝ 141.3 550 165 405 906˝ 168.3 670 195 505 141

D A B R2˝ 60.3 406 203 150 343˝ 88.9 406 203 150 284˝ 114.3 560 280 210 515˝ 141.3 610 305 240 766˝ 168.3 762 381 305 132

D A R C2˝ 60.3 203 150 53 143˝ 88.9 203 150 53 204˝ 114.3 280 210 70 395˝ 141.3 305 240 65 576˝ 168.3 381 305 76 105

D A R C2˝ 60.3 118 150 56 93˝ 88.9 118 150 56 144˝ 114.3 162 210 75 265˝ 141.3 171 240 72 376˝ 168.3 203 305 25 57

Weight approx(kg)

Table 3.6 90º Long Sweep Elbow

Table 3.7 45º Long Sweep Elbow



Table 3.4 45º Lateral Tee


Table 3.5 Long sweep tee c/w integral bull plug

Size All dimensions in mm


D A R C2˝ 60.3 178 152 26 83˝ 88.9 305 229 76 294˝ 114.3 356 305 51 525˝ 141.3 432 381 51 876˝ 168.3 533 457 76 177

D B R C2˝ 60.3 121 152 58 73˝ 88.9 171 229 76 194˝ 114.3 177 305 51 315˝ 141.3 209 381 51 506˝ 168.3 265 457 76 89

D A B2˝ 60.3 70 48 13˝ 88.9 90 60 34˝ 114.3 115 81 65˝ 141.3 140 102 106˝ 168.3 170 126 18

D A B R2˝ 60.3 330 310 150 473˝ 88.9 330 310 150 484˝ 114.3 406 431 210 915˝ 141.3 483 487 240 1336˝ 168.3 686 600 305 238

D A B R2˝ 60.3 406 310 150 483˝ 88.9 406 310 150 514˝ 114.3 560 431 210 975˝ 141.3 610 487 240 1426˝ 168.3 762 600 305 255

Weight approx(kg)

Table 3.10 Bull Plug

All dimensions in mm Weight approx(kg)

Table 3.11 Standpipe Goosneck 160 deg c/w


Table 3.12 Standpipe Goosneck 160 deg c/w

Size

Size All dimensions in mm Weight

Table 3.8 90º 3d Double Backed Bend


Table 3.9 45º 3d Double Backed Bend

Size All dimensions in mm

40

samt innledende tekst som på Word formatetMax Working pressure 5 000 PSI 10 000 PSI 15 000 PSITest pressure 7 500 PSI 15 000 PSI 22 500 PSI

Product specification levels 1, 2, 3 & 4 1, 2, 3 & 4 1, 2, 3 & 4

API temperature ratingK(-60 deg. C) to Y(+345 deg. C)

K(-60 deg. C) to Y(+345 deg. C)

K(-60 deg. C) to Y(+345 deg. C)

Min. Yield 60 000 PSI 60 000 PSI 75 000 PSIMin. Tensile 85 000 PSI 85 000 PSI 95 000 PSIMaterial API 60K API 60K API 75K

Nominal size and bore Outside diameter Total thicknessLarge diameter of neck

B D C A

2 1⁄16 5.031 1.166 3.6562 9⁄16 5.781 1.166 4.4063 1⁄8 6.312 1.166 4.9384 1⁄16 7.625 1.197 6.2507 1⁄16 13.250 1.622 11.6259 13.250 1.622 11.62511 16.250 1.654 14.625

1 13⁄16 5.031 1.166 3.6562 1⁄16 5.781 1.166 4.4062 9⁄16 6.312 1.166 4.9383 1⁄16 7.625 1.197 6.2504 1⁄16 8.437 1.310 6.8127 1⁄16 16.250 1.653 14.6259 16.250 1.653 14.62511 20.625 2.035 18.625

1 13⁄16 5.781 1.166 4.4062 1⁄16 6.125 1.622 4.5002 9⁄16 6.125 1.622 4.5003 1⁄16 8.437 1.310 6.8124 1⁄16 13.250 1.622 11.6257 1⁄16 20.626 2.035 18.62511 22.250 2.309 20.625

1 13⁄16 6.125 1.622 4.5002 1⁄16 6.125 1.622 4.5002 9⁄16 8.437 1.310 6.8123 1⁄16 13.250 1.622 11.6254 1⁄16 16.250 1.653 14.6257 1⁄16 22.250 2.308 20.62511 27.997 3.005 25.000

Table 4.1 API Type 16BX Integral Hub Connections for 5,000 psi Rated Working Pressure

5 000 PSI

10 000 PSI

15 000 PSI

20 000 PSI


Hubs and Clamps are designed and manufactured in accordance with the following specifications:-

API 16A Specification for Drill Through Equipment.API 6A Specification for Wellhead and Christmas Tree Equipment.NACE MR-01-75 Sulphide Stress Cracking Resistant Metallic Materials for Oilfield Equipment.ASME VIII Boiler and Pressure Vessel Code.ANSI B31.3 Chemical Plant and Petroleum Piping.

Hubs are available as Weld Neck, Integral & Blinds and are available in the following materials and pressure ratings:-

Section 4. API Hubs and Clamps

Clamp number

API designated size

Working pressure(PSI)

1 13/16 10 0002 1/16 5 0001 13/16 15 0002 1/16 10 0002 9/16 5 0001 13/16 20 0002 1/16 15 0002 1/16 20 0002 9/16 15 0002 9/16 10 000

3 1/8 5 0003 1/16 10 0004 1/16 5 0002 9/16 20 0003 1/16 15 0004 1/16 10 0003 1/16 20 0004 1/16 15 0007 1/16 5 0009 5 000

6

8

Table 4.2 Clamps for API Type 16B

Dimension E Counterbore is optional

1

2

3

4

5

General notes: Dimensions are in inches

Clamp number

API designated size

Working pressure(PSI)

1 13/16 10 0002 1/16 5 0001 13/16 15 0002 1/16 10 0002 9/16 5 0001 13/16 20 0002 1/16 15 0002 1/16 20 0002 9/16 15 0002 9/16 10 000

3 1/8 5 0003 1/16 10 0004 1/16 5 0002 9/16 20 0003 1/16 15 0004 1/16 10 0003 1/16 20 0004 1/16 15 0007 1/16 5 0009 5 000

6

8

Table 4.2 Clamps for API Type 16B

Dimension E Counterbore is optional

1

2

3

4

5

General notes: Dimensions are in inches


samt innledende tekst som på Word formatetMax Working 5 000 PSI 10 000 PSI 15 000 PSI 20 000 PSITest pressure 7 500 PSI 15 000 PSI 22 500 PSI 30 000 PSIProduct specification levels 1, 2, 3 & 4 1, 2, 3 & 4 1, 2, 3 & 4 1, 2, 3 & 4API temperature rating

K(-60 deg. C) to Y(+345

K(-60 deg. C) to Y(+345

K(-60 deg. C) to Y(+345 deg. C)

K(-60 deg. C) to Y(+345 deg. C)


Normal size and bore

Outside diameter

Total thickness

Large diameter of neck

Neck lenght for clamp clearance

Ring gasket number

Clamp number

B D C A L

2 1⁄16 5.031 1.166 3.656 2.22 BX-152 12 9⁄16 5.781 1.166 4.406 2.27 BX-153 23 1⁄8 6.312 1.166 4.938 2.36 BX-154 44 1⁄16 7.625 1.197 6.250 2.38 BX-155 57 1⁄16 13.250 1.622 11.625 3.38 BX-156 69 13.250 1.622 11.625 3.38 BX-157 811 16.250 1.654 14.625 4.13 BX-158 10

1 13⁄16 5.031 1.166 3.656 2.22 BX-151 12 1⁄16 5.781 1.166 4.406 2.27 BX-152 22 9⁄16 6.312 1.166 4.938 2.36 BX-153 43 1⁄16 7.625 1.197 6.250 2.38 BX-154 54 1⁄16 8.437 1.310 6.812 2.82 BX-155 67 1⁄16 16.250 1.653 14.625 4.13 BX-156 109 16.250 1.653 14.625 4.13 BX-157 1011 20.625 2.035 18.625 4.75 BX-158 22

1 13⁄16 5.781 1.166 4.406 2.27 BX-151 22 1⁄16 6.125 1.622 4.500 3.22 BX-152 32 9⁄16 6.125 1.622 4.500 3.22 BX-153 33 1⁄16 8.437 1.310 6.812 2.82 BX-154 64 1⁄16 13.250 1.622 11.625 3.38 BX-155 87 1⁄16 20.626 2.035 18.625 4.75 BX-156 2211 22.250 2.309 20.625 5.31 BX-158 15

1 13⁄16 6.125 1.622 4.500 3.22 BX-151 32 1⁄16 6.125 1.622 4.500 3.22 BX-152 32 9⁄16 8.437 1.310 6.812 2.82 BX-153 63 1⁄16 13.250 1.622 11.625 3.38 BX-154 84 1⁄16 16.250 1.653 14.625 4.13 BX-155 107 1⁄16 22.250 2.308 20.625 5.31 BX-156 1511 27.997 3.005 25.000 6.17 BX-158 28

Table 4.1 API Type 16BX Integral Hub Connections for 5,000 psi Rated Working Pressure

5 000 PSI

10 000 PSI

15 000 PSI

20 000 PSI

4219. Ring Gaskets

Differences between Ring Type Joint GasketsRTJ gaskets are precision machined from solid metal and are designed for high pressure and high tempera-ture services. They seal by creating very high unit load, metal-to-metal line contact with special mating flang-es. Metals are typically chosen so that thering gasket is softer than the flange material in order to prevent damage to the flanges and thereby causing plastic flow of the gasket into the flange faces. The design of the gasket or cross section is chosen based on the existing flange configuration and designed maximum system pressure. Gasket and flange surface finishes and dimensional accuracy along with gasket hardness must be carefully controlled in order to obtain and maintain an effective seal. Style R • Available in oval and octagonal cross-sections • R gaskets are interchangeable on modern octagonal flat bottom grooved flanges • Standard sizes of Style R gaskets are manufactured in accordance with ASME B16.20 and API 6A specifica-tions Style RX • Style RX ring joint has a unique self-sealing action. The outside bevels of the ring make the initial contact providing a seal against the groove’s outer surfaces. As the internal pressure increases, so does the gasket loading stress against the groove thus improving the gaskets sealing characteristics • Design features of the Style RX gasket make it more resistant to shock load, test pressure shock and drilling vibration • Style RX ring joints are completely interchangeable with standard Style R groove designs. Care should be taken when interchanging these styles as RX gaskets are taller and will add length to the finished assembly Style BX • Style BX gaskets have a pitch diameter slightly larger than the groove pitch diameter. This allows for initial contact to be made on the outside of the ring, pre-loading the gasket which creates a pressure ener-gized seal • All Style BX gaskets incorporate a pressure passage to enable trapped pressure to balance itself in the joint • Style BX ring joint gaskets can only be used with API BX flanges and are not interchangeable with Style RX

Differences between Ring Type Joint GasketsRTJ gaskets are precision machined from solid metal and are designed for high pressure and high temperature services. They seal by creating very high unit load, metal-to-metal line contact with special mating flanges. Metals are typically chosen so that thering gasket is softer than the flange material in order to prevent damage to the flanges and thereby causing plastic flow of thegasket into the flange faces. The design of the gasket or cross section is chosen based on the existing flange configuration and designed maximum system pressure. Gasket and flange surface finishes and dimensional accuracy along with gasket hardness must be carefully controlled in order to obtain and maintain an effective seal.

Style R• Available in oval and octagonal cross-sections• R gaskets are interchangeable on modern

octagonal flat bottom grooved flanges• Standard sizes of Style R gaskets are manufactured in

accordance with ASME B16.20 and API 6A specificationsStyle R- Oval Style R- Octagonal

Style RX• Style RX ring joint has a unique self-sealing action. The outside bevels

of the ring make the initial contact providing a seal against the groove’s outersurfaces. As the internal pressure increases, so does the gasket loading stressagainst the groove thus improving the gaskets sealing characteristics

• Design features of the Style RX gasket make it more resistant to shock load, testpressure shock and drilling vibration

• Style RX ring joints are completely interchangeable with standard Style R groovedesigns. Care should be taken when interchanging these styles as RX gaskets aretaller and will add length to the finished assembly

Style RX

Style BX• Style BX gaskets have a pitch diameter slightly larger than the groove

pitch diameter. This allows for initial contact to be made on the outside of the ring,pre-loading the gasket which creates a pressure energized seal

• All Style BX gaskets incorporate a pressure passage to enable trappedpressure to balance itself in the joint

• Style BX ring joint gaskets can only be used with API BX flanges and are notinterchangeable with Style RX









Style RX













Style RX













Style RX





Style R- Oval Style R- Octagonal

Style BX

Style RX

43

Chart below showing ring gasket sizes & stud sizes for API 6A flanges

20. Chart Gasket & Studs

Chart below showing ring gasket sizes & stud sizes for API 6A flanges

Studs with nutsAPI Flanges Flange size API ring No NO Size Appr. Weight pr. set(lbs)

5 000 PSI WP(6B)

2 1/16" R24/ RX24 8 7/8 x 6 122 9/16" R27/ RX27 8 1 x 6 1/2 173 1/16" R35/ RX35 8 1 1/8 x 7 1/4 244 1/16" R39/ RX39 8 1 1/4 x 8 35

10 000 PSI WP(6BX)

1 13/16" BX-151 8 3/4 x 5 82 1/16" BX-152 8 3/4 x 5 1/4 82 9/16" BX-153 8 7/8 x 6 113 1/16" BX-154 8 1 x 6 3/4 174 1/16" BX-155 8 1 1/8 x 8 267 1/16" BX-156 12 1 1/2 x 11 1/4 95

15 000 PSI WP(6BX)

1 13/16" BX-151 8 7/8 x 5 1/2 91 1/16" BX-152 8 7/8 x 6 112 9/16" BX-153 8 1 x 6 3/4 163 1/16" BX-154 8 1 1/8 x 7 1/2 244 1/16" BX-155 8 1 3/8 x 9 1/4 297 1/16" BX-156 16 1 1/2 x 12 3/4 112

44

Part Nr DescriptionL7G7SB2XN1"X165 STUDBOLT 1" UNC X 165MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN1"X170 STUDBOLT 1" UNC X 170MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN1"X180 STUDBOLT 1" UNC X 180MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN11/2"X260 STUDBOLT 1.1/2" UN X 260 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN11/2"X295 STUDBOLT 1.1/2" UN X 295 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN11/2"X300 STUDBOLT 1.1/2" UN X 300 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN11/4"X210 STUDBOLT 1.1/4" UNC X 210 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN11/8"X200 STUDBOLT 1.1/8" 8UN X 200 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN11/8"X210 STUDBOLT 1.1/8" 8UN X 210 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN11/8"X220 STUDBOLT 1.1/8" 8UN X 220 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN11/8"X240 STUDBOLT 1.1/8" 8UN X 240 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN13/8"X240 STUDBOLT 1.3/8" UNC X 240 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN3/4"X130 STUDBOLT 3/4" UNC X 130 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN3/4"X140 STUDBOLT 3/4" UNC X 140 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN7/8"X140 STUDBOLT 7/8" UNC X 140 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7L7G7SB2XN7/8"X155 STUDBOLT 7/8" UNC X 155 MM C/W 2 NUTS, HOT DIP GALV ASTM A320 L7/A194 GR.7

21. P/N Gasket & Studs

Chart below showing part nr. on ring gasket sizes & stud sizes for API 6A flanges

Part Nr DescriptionR150BX6 RING GASKET BX 150 316 SSR150BXD RING GASKET BX 150 SOFT IRONR151BX6 RING GASKET BX 151 316 SSR151BXD RING GASKET BX 151 SOFT IRONR152BX6 RING GASKET BX 152 316 SSR152BXD RING GASKET BX 152 SOFT IRONR153BX6 RING GASKET BX 153 316 SSR153BXD RING GASKET BX 153 SOFT IRONR154BX6 RING GASKET BX 154 316 SSR154BXD RING GASKET BX 154 SOFT IRONR155BX6 RING GASKET BX 155 316 SSR155BXD RING GASKET BX 155 SOFT IRONR156BX6 RING GASKET BX 156 316 SSR156BXD RING GASKET BX 156 SOFT IRONR157BX6 RING GASKET BX 157 316 SSR157BXD RING GASKET BX 157 SOFT IRONR159BX6 RING GASKET BX 159 316 SSR159BXD RING GASKET BX-159 SOFT IRONR160BX6 RING GASKET BX 160 316 SSR160BXD RING GASKET BX 160 SOFT IRONR163BX6 RING GASKET BX 163 316 SSR163BXD RING GASKET BX 163 SOFT IRONR164BX6 RING GASKET BX 164 316 SSR164BXD RING GASKET BX 164 SOFT IRON

Part Nr DescriptionR169BX6 RING GASKET BX 169 316 SSR169BXD RING GASKET BX 169 SOFT IRONR024R86 RING GASKET R-24 SS316 OCTR024R8D RING GASKET R-24 SOFT IRON OCTR024RO6 RING GASKET R-24 316 SS OVALR024ROD RING GASKET R-24 SOFT IRON OVALR024RX6 RING GASKET RX-24 316 SSR027R86 RING GASKET R-27 SS316 OCTR027R8D RING GASKET R-27 D SOFT IRON OCTR027RO6 RING GASKET R-27 316 SS OVALR027ROD RING GASKET R-27 SOFT IRON OVALR035R86 RING GASKET R-35 316 SS OCTAR035R8D RING GASKET R-35 SOFT IRON OCTAR035RX6 RING GASKET RX-35 316 SSR039R86 RING GASKET R-39 SS316 OCTR039R8D RING GASKET R-39 SOFT IRON OCTR039RO6 RING GASKET R-39 316 SS OVALR039ROD RING GASKET R-39 SOFT IRON OVALR039RX6 RING GASKET RX-39 316 SSR044R86 RING GASKET R-44 SS316 OCTR044R8D RING GASKET R-44 SOFT IRON OCTAR044RO6 RING GASKET R-44 316 SS OVALR044RX6 RING GASKET RX-44 316 SSR044RXD RING GASKET RX-44 SOFT IRON

4522. Other API Valves & Manifolds

API related valves, manifolds & systems in Mento portfolio

Choke valves

Diverter valves Relief valves

Plug valves Control panels Systems

• Engineering • Machining • Fabrication • Service

MECHANICAL SOLUTIONS

Contakt Mento for more information

STAVANGER • BERGEN • KRISTIANSUND • HAMMERFEST +47 48 11 03 00 • 24h +47 90 19 51 55 • [email protected] • mento.no

Environmentally friendly• Thread Compounds• Jacking system grease• Valve grease

• Riser Tensioner Fluids• BOP Control Fluids

OILFIELD SUPPLY

Diaphragm Pumps N° 403-M

HOSES

FILTRATION

VALVES

Ball

Gate, Globe & Check

Butterfly Valves (soft seat & high perfomance)

Mud, API Gate & Chokes Plug Valves

Other Mento products

Hoses for all types of media

Flexible Choke & Kill Line with TauroFlon™ liner (up to 130oC)

ControlValves

Membrane Filter

GLOBALCORE™

The world’s first high-performance, cohesive hose and fitting system.

Five Hoses. Two Fittings. One Solution.

Five Hoses • Two Fittings • One Solution

FLOWLINE EQUIPMENTSale • Rental • Service

Wide range of Bulk Loading Hoses

All brands Filter Units for • Engine • HVAC • Process & Diesel

Tailor made Filter Solutions

your trusted partner in api 6a valves & manifolds

Documents