PERFORATED DIFUSERSPRICE MODEL PDF

OR APPROVED ALTERNATEPERFORATED DIFUSERS

PRICE MODEL PDFOR APPROVED ALTERNATE

PERFORATED RETURN MAXIMUM SQUARE NECKPRICE MODELPDDR

OR APPROVED ALTERNATEPERFORATED RETURN MAXIMUM SQUARE NECK

PRICE MODELPDDROR APPROVED ALTERNATE

20 1, 2, 3, 4

20 1, 2, 3, 4

24x24

0 200 24X12

AIR DEVICE SCHEDULE

NOTES

1, 2, 3, 4

1, 2, 3, 4

150

2150

280

MARK

200R

A 0

151B

C

NOTES: 1. PROVIDE WITH FACTORY-APPLIED, OFF-WHITE ENAMEL FINISH.2. PROVIDE WITH FLUSH MOUNT FRAME OR T-BAR MOUNT FRAME AS REQUIRED TO MATCH CEILING CONDITION. 3. PROVIDE WITH MITERED CORNERS. 4. PROVIDE SQUARE TO ROUND DUCT TRANSITIONS AS REQUIRED.

MAX. NC LEVEL

20

MAKE / MODELMIN. MAX.

FACE SIZE (IN.)

NECK SIZE (IN.)

20

CFM RANGEMAX S.P.

(IN.)

24x24 6"Ø 0.10

- 0.10

8"Ø24x24 0.10

- 0.01

EAT LAT COIL LOADDESIGN MIN. IN. ° ° KW

FTU-10-1FAN POWERED TERMINAL UNIT

250 100 12 55 90 1.1TRANE VCEF

OR APPROVED ALTERNATE

1,2,3

FTU-10-2FAN POWEREDTERMINAL UNIT

480 192 4 55 90 2.1TRANE VCEF

OR APPROVED ALTERNATE

1,2,3

FAN POWERED AIR TERMINAL UNIT SCHEDULEINLET SIZE

NOTES:1. PROVIDE UNIT WITH 480 VOLT, THREE PHASE SINGLE POINT POWER CONNECTION WITH FUSED DISCONNECT.2. PROVIDE SOLID STATE COMULATING HEAT CONTROL FOR ALL HEATING COILS.3. PROVIDE 1" FOIL-FACED FIBROUS GLASS DUCT LINER COMPLYING WITH UL181 AND NFPA 90A.

MARK TERMINAL TYPECFM

NOTESHEATING COIL

MAKE/MODEL

DESIGN MIN. IN.

VAV-7-1SINGLE DUCT

TERMINAL UNIT285 0 6

KRUEGER LMHSOR APPROVED ALTERNATE

1,2

VAV-7-2SINGLE DUCT

TERMINAL UNIT380 0 6

KRUEGER LMHSOR APPROVED ALTERNATE

1,2

VAV-7-3SINGLE DUCT

TERMINAL UNIT200 0 6

KRUEGER LMHSOR APPROVED ALTERNATE

1,2

VAV-10-1SINGLE DUCT

TERMINAL UNIT150 0 6

KRUEGER LMHSOR APPROVED ALTERNATE

1,2

VARIABLE AIR TERMINAL UNIT SCHEDULE

NOTES:1. PROVIDE UNIT WITH 277 VOLT, THREE PHASE SINGLE POINT POWER CONNECTION WITH FUSED DISCONNECT.2. PROVIDE 1" FOIL-FACED FIBROUS GLASS DUCT LINER COMPLYING WITH UL181 AND NFPA 90A.

INLET SIZEMARK TERMINAL TYPE

CFMNOTESMAKE/MODEL

PLUMBING FIXTURE SCHEDULESYMBOL DESCRIPTION MANUFACTURER / MODEL NUMBER WASTE VENT CW HW REMARKS

SK-1 SINK: COUNTER-MOUNTED, SELF-RIMMING, 3-HOLE, 4" CENTERS, ELKAY: LRAD 1918 2" 1-1/2" 3/4" 3/4" OFF-CENTERED REAR DRAIN OPENING(ADA) #18 GAUGE, TYPE 304 STAINLESS STEEL, 6-1/2" DEEP, SINGLE-BOWL

FAUCET: SWING NECK, 3-HOLE WITH DECK PLATE MOEN: 8701 PROVIDE 1.5 GPM VANDAL-RESISTANT AERATORSTRAINER: GRID-TYPE w/ DRAIN COVER McGUIRE: 1151AWCTRAP McGUIRE: 8903 1-1/2" INLET X 2" OUTLETSUPPLIES: BRASS STOPS & COPPER RISERS, CHROME PLATED McGUIRE: 2167CCLK LOOSE KEY, 1/2" RISERSCOVERS (NOT REQ'D IF ARCHITECTURAL COVER PROVIDED) TRUBRO: LAV GUARD2, 103 E-Z FOR STOPS, STRAINER, AND P-TRAP

IMB ICE MACHINE BOX: SIOUX CHIEF: 696-10 SERIES "OX BOX" - - 3/4" - INCLUDE WATER HAMMER ARRESTOR.

IM ICE MAKER (BY OTHERS) - - 1/2" - INCLUDE CHROME-PLATED VACUUM BREAKER IN WATER SUPPLY:CHICAGO MODEL 892-G OR APPROVED EQUAL. LOCATE 6" MIN.ABOVE TOP OF ICE MAKER & ALL DOWNSTREAM PIPING.

DW DISHWASHER (BY OTHERS) 5/8" - - 1/2" CONNECT WASTE TUBE THROUGH CHROME-PLATED AIR-GAP FITTING ABOVE COUNTERTOP TO SINK TAILPIECE.

NOTES:

1) REFER TO THE ARCHITECTURAL DRAWINGS FOR EQUIPMENT AND ACCESSORY LOCATIONS. NOTIFY ARCHITECT AND ENGINEER OF ANY CONFLICTS.

2) REFER TO THE ARCHITECTURAL DRAWINGS FOR SPECIFIC MOUNTING HEIGHTS FOR ALL FIXTURES.