002 basic design rules sabic ip
DESCRIPTION
plastic product designTRANSCRIPT
Design Guidelines Injection Moulding
Engineering Design
Presenter: Laszlo PatakiSABIC-Innovative Plastics
3Design Guidelines Injection Moulding
Successful injection moulding depends on the good interaction between:
1.Part Design
2.Mould Design
3.Processing Equipment and process control
4.Material selection.
Design Guidelines Injection Moulding
5Design Guidelines Injection Moulding
1, Part Design Aspects
Firstly, part requirements have to be defined.
• Mechanical behavior (stiffness, impact)
• Thermal behavior ( stiffness, Creep)
• Chemical resistance ( material selection)
• Cosmetics (surface finish, color, gate location, ribs, weld line)
• Mould ability ( wall thickness, flow length, gating …)
• Assembly ( screws, welding , bonding…)
• Painting
Design Guidelines Injection Moulding
6
Design Guidelines Injection Moulding
Part Design aspects
• Design for mould ability
• Design for stiffness
• Design for impact
• Design for appearance
• Design for precision.
7Design Guidelines Injection Moulding
1, Design for Mould ability
• Constant wall thickness recommended
• If not possible, transitions should be smooth.
Design Guidelines Injection Moulding
8Design Guidelines Injection Moulding
Design for Mould ability
• Ribs - if needed - max.0.6 x nominal wall at root,
min.0.5 degree draft on each side.
• Filling thin ribs can be problematic
Design Guidelines Injection Moulding
9Design Guidelines Injection Moulding
Design for Mould ability
• Bosses for screws same rule as ribs, to increase stiffness boss can be supported with gussets.
• Sharp corners rounded off , better release, better strength.
Design Guidelines Injection Moulding
10Design Guidelines Injection Moulding
Design for Mould ability
• Undercuts should be avoided where possible.
If needed, use undercuts without sliding cores.
Design Guidelines Injection Moulding
11
Design Guidelines Injection Moulding
Design for Mould ability
• Draft angles
12
Design Guidelines Injection Moulding
Design for Mould ability
• Ejection
Allow for sufficient ejection locations, specially complex shapes with many ribs and pockets can be critical with higher viscous materials.
Ribs are best ejected on the rib itself with blade ejectors.
Use as large as possible ejector pins, lowest deformations will occur.
13
Design Guidelines Injection Moulding
Gating• Flow should be from thick to thin, if not constant wall thickness.
• Gate location(s) to be considered to prevent filling issues. Flow curves can be used for first check.
14
Design Guidelines Injection Moulding
Design for Mould ability Gate shapes
Gate size is importantfor shear rate control
Flow simulation usefulfor predicting shear and pressure drop.
15
Design Guidelines Injection Moulding
• VentingImportant for part quality.
Good venting is always needed where air traps and weld lines
are expected , also at the end of flow.
Dynamic vents ( using ejectors with facets) are suitable for local air traps, mould parting line should always be vented.
Size of venting depending on material viscosity.
16
Design for stiffness
Part stiffness determined by:
1. Material E module
2. Shape of the part
Stiffness increase
• Higher E module
• Ribs
• Corrugations
• Hollow parts
Design Guidelines Injection Moulding
17
Design Guidelines Injection Moulding
Design for stiffness
Stiffness to weight ratio.
Most efficient material use in corrugated design.
Structural analysis can help to check mechanical
behavior in advance.
18
Design Guidelines Injection Moulding
Design for impact• Avoid stress concentrators ( sharp corners, transitions, notches)
• Avoid impact load near gates and weld lines
• Avoid poor processing conditions (moulded in stress)
• Choose the right material ( ductile /brittle transition)
• In critical cases perform structural analysis.
19
Design Guidelines Injection Moulding
Design for Appearance
Possible surface defects
• gate marks
• sink marks due to ribbing or thick sections
• weld lines
• air traps.
• voids
• jetting
20
Design Guidelines Injection Moulding
Design for AppearanceSink mark reduction
Gas assist can reduce sink marksUnder ribs
Design feature appliedTo eliminate visible sink mark
21
Design Guidelines Injection Moulding
Design for Appearance
Sudden changes in thickness should be avoided
22
Design Guidelines Injection Moulding
Design for Appearance
Try to avoid jetting when choosingthe gate location
23
Design Guidelines Injection Moulding
Design for Precision
Important factors:
• material choice (GF, GB, CF, Amorphous, Crystalline), shrinkage behavior
• gating (type and size of gate)
• mould design ( cooling, gating)
• processing ( temperatures , pressures, orientation)
24
Design Guidelines Injection Moulding
Design for Precision
Volumetric Shrinkage Amorphous
25
Design Guidelines Injection Moulding
Design for Precision
Volumetric Shrinkage Crystalline
26Design Guidelines Injection Moulding
Design for Precision (shrinkage control)
Design related aspects for precision
• Wall thickness distribution
• gate location, gate size, gate type
Processing related aspects
• melt-mould temperature , injection profile
Post moulding effects
• Expansion, post shrinkage, moisture absorption
Design Guidelines Injection Moulding
27
Design Guidelines Injection Moulding
Design for Precision
• Gating type and size important for orientation
• shrinkage differences between flow and cross flow for Crystalline and glass filled materials.
28
Design Guidelines Injection Moulding
Design for Precision
Thin long ribs shrink different compared to nominal wallthis can cause warpage.
29
Thank you for your attention
Design Guidelines Injection Moulding