a1 a2 quick guide

5
UPS A1 & A2 Quick Guide User’s Manual

Upload: italo-vignoli

Post on 09-Mar-2016

232 views

Category:

Documents


2 download

DESCRIPTION

UPS A1 & A2 Quick Guide User’s Manual Spare time 5 minutes (PC LOAD) Output mode Sockets 15] Copyright AST 2010 www.ast-global.com Safety Symbols Means Communication interface 1. Table 1 Safety Symbols and Means 2. Table 2 UPS Main Performance Index Secure alarm Specifications are subject to change without prior notice. Risk of electric shock A1 & A2 QUICK GUIDE

TRANSCRIPT

Page 1: A1 A2 Quick Guide

 

UPS A1 & A2 Quick Guide User’s Manual

Page 2: A1 A2 Quick Guide

A1 & A2 QUICK GUIDE

15] Copyright AST 2010 www.ast-global.com

1. Table 1 Safety Symbols and Means Safety Symbols Means

Secure alarm

Risk of electric shock

2. Table 2 UPS Main Performance Index

Index Model A1 A2

Rating voltage (V) In range 160~290V full load

Rating frequency (Hz) 50±5%

Input mode Single-phase three-line

Inpu

t

Cha

ract

eris

tic

Battery voltage (V) 36 72

Capacity (VA/W) 1000/700 2000/1400

Voltage (V) 230±2%

Frequency (Hz) 50±0.2% (Battery mode)

Waveform Sine wave

Voltage distortion

factor THD < 3% (Linear load)

Power factor 0.7 (Lag)

Switching time (ms) 0

Overload capacity 105%~130% Load, lasting 60 seconds. 135%~150% Load, lasting 30 seconds.≥150%

lasting 300 milliseconds

Out

put C

hara

cter

istic

Output mode Sockets

Spare time 5 minutes

(PC LOAD)

5 minutes

(PC LOAD)

Charge recovery time <12 hours (Standard time delay model)

Communication

interface

A1 & A2: RS232 & USB interface

RS232 interface supports UPS power management software UPSilon 2000 and SNMP

adapter

Panel display LED displays operation status of UPS

Warning function Battery low voltage, abnormal power supply, UPS malfunction

Protection function Battery low voltage protection, overload protection, short-circuit protection and excess

temperature protection

Frequency noise (dB) < 45

Working temperature 0 ~ 40℃

Relative humidity 0 ~ 95%, No condensation

Size (mm)(H × W × D) 88×440×500

Oth

er C

hara

cter

istic

s

Weight (kg) 14 11 ◆ Specifications are subject to change without prior notice.

Page 3: A1 A2 Quick Guide

A1 & A2 QUICK GUIDE

15] Copyright AST 2010 www.ast-global.com

3. Rear Panel

AC OUTPUT

FAN

AC OUTPUT SOCKET

(REAR PANEL)

RS232 PORTBREAKER

AC INPUT、DC INPUT TERMINAL

USB PORT

RS232 USBFUSE

AC INPUT

直流输入/DC INPUT

A1 Rear Panel

FANRS232 PORT FANBREAKER

AC INPUT、DC INPUT TERMINAL

REAR PANEL

USB PORT

RS232 USBFUSE

AC OUTPUT SOCKET

AC OUTPUTAC INPUT

(+) BATTERY (-) DC INPUT

A2 Rear Panel

Page 4: A1 A2 Quick Guide

A1 & A2 QUICK GUIDE

15] Copyright AST 2010 www.ast-global.com

(REAR PANEL)

RS232 PORT

BREAKER

USB PORT

RS

232

US

BFU

SE

AC OUTPUT SOCKET

AC

INPU

T

直流输入

/DC

INP

UT

FAN

DC INPUTLINE BAR

AC INPUT SOCKET

AC O

UTP

UT

RS232 PORT

BREAKER

USB PORT

RS2

32U

SB

FUS

E

AC OUTPUT SOCKET

FAN

AC INPUT、DC INPUT TERMINAL

(REAR PANEL)

AC

OU

TPU

T

AC

INPU

T

(+) B

ATT

ERY

(-)

DC

INPU

T

Horizontal A1 Horizontal A2

4. Preparations before First Start-up

To ensure normal operation of UPS, please confirm the following before use: A. Correct installation of input and output. B. If supply terminals connect to the rated power. . C. Confirm that UPS output does not short circuit, and the load capacity does not exceed UPS capacity. D. Confirm if computer or other instrument is turned off. E. Confirm if battery voltage is normal. F. It is not recommended to connect reactive load to the UPS output. Loads are normally powered by electric network directly.

5. UPS Start-up Sequence

After confirming all the above, please start the machine by following means:

A. Press the "POWER" button on the UPS panel to start UPS, the "INV" indicator light will light up. After retardation time, the "BYP." light goes out and the UPS is changed inversion power supply. By this time, the start-up is completed and the equipment starts operation. Wait for about 20 seconds after normal no-load operation to turn on the computer or other instrument. Start the load in the sequence of high-power to low power, first start the high-power equipment then in turns start equipment with lower power.

B. Start computer or other equipment.

Page 5: A1 A2 Quick Guide

A1 & A2 QUICK GUIDE

15] Copyright AST 2010 www.ast-global.com

6. Daily Start-up and Shutdown

During daily operation, operate as per the following for start-up or shut down: A. Press the "ON" button on the UPS panel to start UPS, after 20 seconds, turn on the computer or other

instrument. B. Normally, only when the UPS has been started and is working stably, can the loading equipment power switch be turned on. First turn on high-power equipment, then the equipment with lower power. Some equipment has large start current (such as monitors of some brands). When starting such equipment, overload protection (such as bypass operation) may occur. In this case, it's recommended to start this type of equipment before other equipment. C. Before shutdown, turn off the computer and other instrument first. Then press the "OFF" button on the

panel for seconds.

7. Maintenance Guide

The correct maintenance, including the preventative maintenance and remedial maintenance, is the key to the

best operation and longer usage life of the UPS. The preventive maintenance includes some regular programs

to avoid the faults of the power system and reach maximum efficiency. The remedial maintenance includes the

probing of the power system fault for the effective maintenance.

8. Safety Precaution

For safe and smooth maintenance on the power system, you must follow the related safety precautions, prepare the necessary gears and testing equipments and operate under the eligible maintainer’s control. Pay attention to the following safety operation regulations:

A. Do remember there always exits hazardous voltage inside UPS even when UPS do not run. B. Make sure persons manipulating or maintaining UPS are familiar with the manual and instrument. C. When UPS operation, no golden or sliver accouterments like ring, watch wore. D. Do assume the safe operation procedure as a matter of course. If any doubt, consult with persons being familiar with the instrument. E. Keep eye on the hazardous voltage inside the UPS every moment. Using voltmeter to check if the input power is completely cutoff and in safe status before maintenance and adjustability.

Please comply with the manual to use UPS. When UPS faults, please cut off the connection between battery cabinet and UPS immediately then deliver it to professional maintainer or station. Self-deal is prohibited.