HBS Electronic GmbH

ACS - Power SourceACS - Power SourceACS - Power Source

Thanks to the well designed li-near power booster the ACS canfeed the connected load constant-ly and with high reliability. For thisthe operator will face a wide ope-ration spectrum in the areas ofcommercial nets, supply nets,and aircraft board supply begin-ning from the first laboratory testsup to the mass production.

The digital DDS signal generationof the ACS Power Source provi-des a very clean and pure sinewave AC voltage with a distortionless than 0.2%.

The AC, DC, AC+DC mode ex-pands the operation possibilitiesin many areas.

Input and measure values aredisplayed on a vacuum fluores-cence display of high intensity.The operation can be simplymade via push buttons and tur-ning knobs.

Using the integrated RS232 Inter-face and the available optional In-terfaces all ACS Power PowerSource settings and measure-ments can be completely control-led with an PC.

With the option ‘sequence’ theoperator can simulate fast transi-ents, voltage drops, voltage rises,etc.

The complete power line simulation

commercial TestingAvionics TestingAC / DC Mode1 and 3-Phase operationlinear PowerboosterPower from 400 - 6000 VA

Voltage range Standard0 - 300 V AC0 - 425 V DCVoltage range HV (Option)0 - 500 V AC0 - 700 V DCVoltage range XHV (Option)0 - 700 V AC0 - 1000 V DC

Frequency range Standard0 - 500 HzFrequency range F1 (Option)0 - 1000 HzFrequency range F2 (Option)0 - 2000 Hz

distortion < 0,2%

MeasurementsVoltage(V), Current(A), Peakcurrent(A),effective Power(W), apparent Power(VA),Powerfaktor, Crestfaktor

Voltage and Current constant-Mode

programmable start up phaseangle

20 programmable Device-States

20 programmable sequences(Option)

RS232 Interfacewith galvanic isolation StandardInterface (Option)with galvanic isolationIEEE488, USB, LAN

external Oscillator Input (Option)with galvanic isolation

3-Phase-Mode (Option)

built in Output-Relais

protection for power- voltage-,current and temperature overload

HBS Electronic2

ACS - Power SourceACS - Power SourceACS - Power Source

programmable sequences (Option)

With the ACS-Power Source you can generate automatic test-command-sets (Sequences). Youcan store 20 Sequences with 50 commands for call back later. The function can be used to ge-nerate voltage dropouts etc. The minimum time-step of on Sequence is 10 ms. To generate andtransfer sequences you can use the PC-program tool(ACS-Control) or remote commands.

generate a linear voltage ramp with the Option‘Sequence’.

generate a voltage dropout on Phase 1 for10ms duration with the Option „Sequence“ ona 3-phase system.

the succession of an sequence for 10ms/100VAC, 10ms/130VAC, 20ms/100VAC on 400 Hzrepeating 2 times.

HBS Electronic 3

ACS - Power SourceACS - Power SourceACS - Power Source

The software tool ACS-Control uses an Soft-Controlpanel for remote control the ACS-Power Source over PC.

available functions:setting values / parametersdisplay measurementsgenerate, transfer, load, save and compu-ting sequences.generate, transfer, load, save and compu-ting easy to use test-command-sets

For the generation of sequences the SoftwareACS-Control gives you an easy to use Sequen-ce-Table.

available functions:generate, load, save sequences to hard disk.transfer sequences to the ACS-Power-Sour-ceload, save and computing sequences in theuser ACS-Power Source RAM.Start and Stop sequences

The Software ACS-Control gives you also anfunction for generation of simple testcom-mand-sets to make settings and measure-ments for testing equipment.

available functions:generate, load, save and computing test-command-sets.measurement comparing for upper and lo-wer-limitsreport test-stepsload, save and print test-reports

Application software (Option)

HBS Electronic4

ACS - Power SourceACS - Power SourceACS - Power Source

SpecificationsTyp ACS-0400-PS ACS-0800-PS ACS-1600-PS

Power Output (VA) 400 / 500** extended for 1 minute

800 / 1000** extended for 1 minute

1600 / 2000** extended for 1 minute

Voltage-RangeStandard

0-300VAC0-425VDC

0-300VAC0-425VDC

0-300VAC0-425VDC

Voltage-Range(Option HV)

0-500VAC0-700VDC

0-500VAC0-700VDC

0-500VAC0-700VDC

Voltage-Range(Option XHV)

0-700VAC0-1000VDC

0-700VAC0-1000VDC

0-700VAC0-1000VDC

Maximum Current r.m.s.(Option HV)(Option XHV)

3A1,8A1,5A

6A3,6A3A

12A7,2A6A

Maximum Current DC(Option HV)(Option XHV)

3A1,8A1,5A

6A3,6A3A

12A7,2A6A

Max. period. peak Current(Option HV)(Option XHV)

8A4,8A4A

20A12A10A

40A24A20A

Creast Factor 2,6 3,3 3,3

Line Regulation 0,1% 0,1% 0,1%

Load Regulationon Nominalpower

0,1% 0,1% 0,1%

Distortionon Nominalpower

0,2% 0,2% 0,2%

Programming AccuracyAC-Voltage

0,1%(10-400Hz)

0,1%(10-400Hz)

0,1%(10-400Hz)

Programming AccuracyDC-Voltage

0,1% 0,1% 0,1%

Programming AccuracyConstantcurrent r.m.s.

0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)

Programming AccuracyFrequency

0,1HzOption 0,01Hz

0,1HzOption 0,01Hz

0,1HzOption 0,01Hz

Programming AccuracySwitch On Phase

0,1 degree 0,1 degree 0,1 degree

Frequency StandardFrequency (Option F1)Frequency (Option F2)

500Hz1 kHz2 kHz

500Hz1 kHz2 kHz

500Hz1 kHz2 kHz

External Oscillator InputFrequency StandardFrequency (Option F1)Frequency (Option F2)

20VssDC-500 HzDC-1 kHzDC-2 kHz

20VssDC-500 HzDC-1 kHzDC-2 kHz

20VssDC-500 HzDC-1 kHzDC-2 kHz

Measurement Voltage r.m.s. 0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)

Measurement Current r.m.s. 0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)

Measurement Current peak 0,8% 0,8% 0,8%

Measurement Real Power 0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)

externalOscillator input (Option T)with optical isolation

Option Option Option

Interfacewith optical isolationIEEE488,USB,LAN

Option

RS232 Standard

Option

RS232 Standard

Option

RS232 Standard

chassis 19“ 19“ 3HE, weight 17Kgdeepness 590mm

19“ 3HE, weight 19Kgdeepness 590mm

19“ 6HE, weight 32Kgdeepness 590mm

HBS Electronic 5

ACS - Power SourceACS - Power SourceACS - Power Source

SpecificationsTyp ACS-2200-PS ACS-3000-PS ACS-4600-PS ACS-6000-PS

Power Output (VA) 2200 / 2750** extended for 1 minute

3000 / 3750** extended for 1 minute

4600 / 5750** extended for 1 minute

6000 / 6000** extended for 1 minute

Voltage-RangeStandard

0-300VAC0-425VDC

0-300VAC0-425VDC

0-300VAC0-425VDC

0-300VAC0-425VDC

Voltage-Range(Option HV)

0-500VAC0-700VDC

0-500VAC0-700VDC

0-500VAC0-700VDC

0-500VAC0-700VDC

Voltage-Range(Option XHV)

0-700VAC0-1000VDC

0-700VAC0-1000VDC

0-700VAC0-1000VDC

0-700VAC0-1000VDC

Maximum Current r.m.s.(Option HV)(Option XHV)

16A9,6A8A

20A12A10A

30A18A15A

40A24A20A

Maximum Current DC(Option HV)(Option XHV)

16A9,6A8A

20A12A10A

30A18A15A

40A24A20A

Max. period. peak Current(Option HV)(Option XHV)

60A36A30A

80A48A40A

100A60A50A

120A72A60A

Creast Factor 3,75 4 4 3

Line Regulation 0,1% 0,1% 0,1% 0,1%

Load Regulationon Nominalpower

0,1% 0,1% 0,1% 0,1%

Distortionon Nominalpower

0,2% 0,2% 0,2% 0,2%

Programming AccuracyAC-Voltage

0,1%(10-400Hz)

0,1%(10-400Hz)

0,1%(10-400Hz)

0,1%(10-400Hz)

Programming AccuracyDC-Voltage

0,1% 0,1% 0,1% 0,1%

Programming AccuracyConstantcurrent r.m.s.

0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)

Programming AccuracyFrequency

0,1HzOption 0,01Hz

0,1HzOption 0,01Hz

0,1HzOption 0,01Hz

0,1HzOption 0,01Hz

Programming AccuracySwitch On Phase

0,1 degree 0,1 degree 0,1 degree 0,1 degree

Frequency StandardFrequency (Option F1)Frequency (Option F2)

500Hz1 kHz2 kHz

500Hz1 kHz2 kHz

500Hz1 kHz2 kHz

500Hz1 kHz2 kHz

External Oscillator InputFrequency StandardFrequency (Option F1)Frequency (Option F2)

20VssDC-500 HzDC-1 kHzDC-2 kHz

20VssDC-500 HzDC-1 kHzDC-2 kHz

20VssDC-500 HzDC-1 kHzDC-2 kHz

20VssDC-500 HzDC-1 kHzDC-2 kHz

Measurement Voltage r.m.s. 0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)´

0,2%(40-400Hz)

Measurement Current r.m.s. 0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)

Measurement Current peak 0,8% 0,8% 0,8% 0,8%

Measurement Real Power 0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)

0,2%(40-400Hz)

externalOscillator Input (Option T)with optical isolation

Option Option Option Option

Interfacewith optical isolationIEEE488, USB, LAN

Option

RS232 Standard

Option

RS232 Standard

Option

RS232 Standard

Option

RS232 Standard

chassis 19“ 19“ 6HE, weight 34Kgdeepness 590mm

19“ 6HE, weight 38Kgdeepness 590mm

19“ 12HE, weight 64Kgdeepness 590mm

19“ 12HE, weight 64Kgdeepness 590mm

HBS Electronic6

ACS - Power SourceACS - Power SourceACS - Power Source

AF-

0314

-03.

20

Order Information

TypesACS-0400-PS Power 400 / 500* VAACS-0800-PS Power 800 / 1000* VAACS-1600-PS Power 1600 / 2000* VAACS-2200-PS Power 2200 / 2750* VAACS-3000-PS Power 3000 / 3750* VAACS-4600-PS Power 4600 / 5750* VAACS-6000-PS Power 6000 / 6000* VA

* extended for 1 minute

OptionsHV extended voltage range 1

0 - 500 V AC / 0 - 700 V DCXHV extended voltage range 2

0 - 700 V AC / 0 - 1000 V DCF1 extended frequency range 1

0 - 1000 HzF2 extended frequency range 2

0 - 2000 HzIEEE488 IEEE488 InterfaceUSB USB InterfaceLAN LAN and USB InterfaceSEQ programmable SequencesT external Oscillator Input

with galvanic isolation3P 3 Phase-Mode

HBS Electronic GmbHHBS Electronic GmbHHBS Electronic GmbHMannheimer Straße 89-91Mannheimer Straße 89-91Mannheimer Straße 89-91

68782 Bruehl68782 Bruehl68782 BruehlTel. 06202 / 97 87 46-0Fax 06202 / 97 87 46-6

email info@hbs-electronic.dewww.hbs-electronic.de

Copyright © HBS Electronic GmbH. All rights reserved. changes without notice.