apple watch cad drawings

Band Design Guidelinesfor Apple WatchRelease R2

Contents

1. Introduction 41.1 Purpose of This Specification 41.2 Requirements and Recommendations 4

2. Watch Bands 52.1 Requirements 52.2 Apple Watch Band Interface 72.3 Apple Watch Lug 8

3. Device Dimensional Drawings 93.1 Apple Watch 38 mm 103.2 Apple Watch 42 mm 11

4. Revision History 12

2015-05-06 | Copyright © 2015 Apple Inc. All Rights Reserved.

2

Figures

2. Watch Bands 5Figure 2-1 Apple Watch Band Interface 7Figure 2-2 Apple Watch Lug 8

3. Device Dimensional Drawings 9Figure 3-1 Apple Watch 38 mm Dimensional Drawing 10Figure 3-2 Apple Watch 42 mm Dimensional Drawing 11


3

Note: These Band Design Guidelines for Apple Watch (including without limitation any and allspecifications relating to Apple Watch lugs) ('Guidelines') are subject to the terms and conditionsset forth on the final page of this document. By downloading, accessing, or otherwise utilizing theseGuidelines, you agree to be bound by, and only utilize the Guidelines in accordance with, such termsand conditions.

These Guidelines do not entitle you to use the "Made for Apple Watch" name or logo, and you agreenot to use the foregoing in connection with any Apple Watch band, accessory, or otherwise, exceptas expressly authorized by Apple in a separate written agreement.

1.1 Purpose of This SpecificationThis document presents design guidelines for band accessories that are compatible with Apple Watch.

1.2 Requirements and RecommendationsThe use of the words must , must not , required , shall , shall not , should , should not , recommended , notrecommended , may , optional , and deprecated in a statement have the following meanings:

● must , shall , or required means the statement is an absolute requirement.

● must not , shall not or prohibited means the statement is an absolute prohibition.

● should or recommended means the full implications must be understood before choosing a differentcourse.

● should not or not recommended means the full implications must be understood before choosing thiscourse.

● may or optional means the statement is truly optional, and its presence or absence cannot be assumed.

● deprecated means the statement is provided for historical purposes only and is equivalent to 'must not'.


4

1. Introduction

A well-designed band will securely attach to Apple Watch while not interfering with its operation. See DeviceDimensional Drawings (page 9) for Apple Watch dimensional drawings with defined keepout zones.

2.1 RequirementsBands for Apple Watch must integrate two lugs that mate with the Apple Watch Band Interface (see AppleWatch Band Interface (page 7)). Apple Watch uses a high precision interface profile; see https://developer.ap-ple.com/watch/bands/ for a sample 2D lug profile. Lugs should lock into the band mating slot with a 'lug latch'feature that prevents accidental removal of the band.

Exposed edges of bands and lugs must pass UL 1439 tests for sharpness of edges on equipment and BSEN71-1:2014, Safety of Toys - Mechanical and physical properties .

The lug latch must never become jammed in the extended position.

Bands must not integrate magnetic chargers.

Bands and lugs should:

● pass a 72 hour salt mist test as specified in ASTM B117 with no visible corrosion

● resist a 5-20 kgf lateral slide-out force when installed in Apple Watch

● resist a 20 kgf or greater pull force as specified in ISO-6245:1996, Specifications for Diver's Watches , section7.3

● detach easily from Apple Watch when the band release buttons are pressed

● take into account the weight of Apple Watch

For compatibility with Apple Watch heart rate sensors, bands should:

● have length sizing adjustment pitch of less than 7 mm (center to center)

● provide sufficient adjustability for the user to achieve a snug, yet comfortable, fit that prevents movementof Apple Watch relative to skin


5

2. Watch Bands

https://developer.apple.com/watch/bands/


Bands must not prevent the user's skin from maintaining direct contact with the Apple Watch heart rate sensorsand back of Apple Watch, and must incorporate sufficient margin to compensate for shifting or dimensionalchanges of the band material. Failure to do so may interfere with Apple Watch wrist detect and Apple Payfeatures.

Bands intended for use during exercise should maintain a snug fit through a full range of motion to maintaincompatibility with Apple Watch heart rate sensors.

Apple recommends the following materials for lug bodies:

● silicone, hardness: 75 shore A

● 50-55% glass filled nylon

● stainless steel 316L (EN 1.4435), hardness: 240-270HV

Apple recommends the following materials for lug latches:

● 50-55% glass filled nylon

● stainless steel 316L (EN 1.4435), hardness: 240-270HV

Bands for Apple Watch must comply with applicable environmental regulations in the regions in which suchbands are to be sold, and any applicable substance or material restrictions, including applicable restrictionson the following substances:

● organic tin compounds, PFOS, PFOA, phthalates, azo dyes, and PAHs, per requirements of the EU REAChregulation EC 1907/2006

● nickel leach rate on surfaces in prolonged skin contact, per requirements of the EU REACh regulation EC1907/2006

● cadmium, lead, hexavalent chromium, and nickel, per requirements of EU Directive 2009/48/EC

● natural rubber latex, per requirements of EU Directive EC 93/42/EEC

● dimethylfumarate (DMFu), per requirements of EU Regulation 412/2012

● pH and Formaldehyde, per requirements of China GB 18401 for textiles and China GB 20400 for leather

● endangered species of flora and fauna in products or packaging (US Lacey Act)

Apple Watch Lug components will be made available through an authorized distributor for integration intothird party bands. See Apple Watch Lug (page 8) for a dimensional drawing. Details will be posted athttps://developer.apple.com/watch/bands/.

2. Watch Bands

2.1 Requirements


6


2.2 Apple Watch Band Interface

Figure 2-1 Apple Watch Band Interface

2. Watch Bands

2.2 Apple Watch Band Interface


7

2.3 Apple Watch Lug

Figure 2-2 Apple Watch Lug

2. Watch Bands

2.3 Apple Watch Lug


8

This chapter contains the following dimensional drawings:

● Apple Watch 38 mm (page 10)

● Apple Watch 42 mm (page 11)


9

3. Device Dimensional Drawings

3.1 Apple Watch 38 mm

Figure 3-1 Apple Watch 38 mm Dimensional Drawing




10


Figure 3-2 Apple Watch 42 mm Dimensional Drawing




11

This table describes the changes to the Band Design Guidelines for Apple Watch.

NotesDate

Release R22015-05-06

Updated Dimensional Drawings

Release R12015-04-24

First Release of "Band Design Guidelines for Apple Watch"


12

4. Revision History

apple watch cad drawings

Technology