ar minimum required special tools starter kit...

2020September

Electric Vehicles £1.075,20

Total £1.075,20

All except Engines and Transmissions £20.655,00Petrol Engines £2.639,70Diesel Engines £1.964,20Manual Transmission £8,80Automatic Transmission £46,00

Total £25.313,70

All except Engines and Transmissions £3.028,90Petrol Engines £0,00Diesel Engines £365,88Manual Transmission £12,30Automatic Transmission (No essential tools in Level I, II) £0,00

Total £3.407,08

CNG & LPG Vehicles £1.559,60

Total £1.559,60

Diagnostics £4.282,80

Total £4.282,80

incl. Test & Mesurement:

£5.842,40

Test & Measurement

Special Service ToolsCNG & LPG


£5.358,00Special Service ToolsPassenger Cars, SUV


£29.596,50Special Service ToolsCommercial Vehicles, LCV


£7.689,88

Opel / Vauxhall

Electric Vehicles

AR minimum required Special Tools Starter Kit 2020Maintenance-related (Class 1 and 2, essential)Covering all car lines within the last 2-year car park

Tool No. PCD-No.

Diagnostic Laptop

EL-51578-EU £ 188,40 £ 188,40

EL-35616-58 £ 10,00 £ 10,00

EL-47955-1 £ 21,80 £ 21,80

EL-50334-200 £ 44,90 £ 44,90

EL-50448 £ 57,10 £ 57,10

EL-51372-EU £ 64,40 £ 64,40

EL-52100-OV £ 793,50 £ 793,50

EL-52425 £ 879,00 £ 879,00

EL-52523 £ 273,00 £ 273,00

EN-50422-EU £ 142,30 £ 142,30

J-35616-F £ 382,30 £ 382,30

KM-J-42000-EU-B £ 1.055,00 £ 1.055,00

KM-J-42000-PR-A £ 269,40 £ 269,40

WE160001A £ 101,70 £ 101,70

£ 4.282,80

Thermoprinter for OPEL Battery Tester

TPMS Valve Installer Kit

Battery Tester OPEL

Probe, Female Connector

O/V-VCI Self-Test Loop Back Adapter

USB-Adaptercable

Tyre Pressure Monitor Sensor Activation Tool

MAT,CAMERA CALIBRATION

Opel/Vauxhall-VCI

Calibration Target

Discharger Unit

AdBlue - Diagnostic Kit

Terminal Test Kit

List Price 01.09.2020

List price (for sum up purpose,

repeated tools excluded)

MOST Bus Diagnostic Kit

Diagnostics

Tool Name

please see below

S410-GME-* £ 1.727,80 £ 1.953,00

* stands for specific keyboard-language

opel.service-solutions.com

Getac semi rugged Notebook S410 - Windows 10

for more information about specifications, service and benefits of the diagnostic laptops:

Available diagnostic laptop

Tool No. PCD-No. Tool Name

0015 0015 2x Lifting Ring Kit 2 To adapt the lift strap kit 0019 onto the battery module. 2 Lifting Ring Kits are needed. £ 104,00 £ 104,00

0017 0017 Load Balancer 2 To lift and lower the battery module. £ 148,90 £ 148,90

0018 0018 Transverse lifting bars 2 To adapt the lift strap kit 0019 to the load balancer 0017. £ 87,90 £ 87,90

0019 0019 3x Lift Strap Kit 2 Use the lift straps to lift or move various loads in accordance with the workshop manual of the PSA Group. 3 Lift Strap Kits are needed. £ 135,40 £ 135,40

12116 12116 Traction battery centering device 2 To safely center the battery onto the body of the car. £ 39,10 £ 39,10

12117 12117 Test Probes 1 The Test Probes are used together with the “VAT1 - Voltage absence detector” to test the absence of voltage during the switch-off procedure of Electric/Hybrid vehicles. £ 30,30 £ 30,30

CPSA-VEH1 CPSA-VEH1 Case of insulated tools 1 This insulated tools are needed to absence of voltage during the switch-off / switch-on procedure to put the vehicle in electrical safety. £ 153,90 £ 153,90

CTRL-ISOL CTRL-ISOL Insulation Tester 1 Needed for checking the insulation of the traction battery during the switch-on procedure of Electric/Hybrid Vehicles. Tool for measuring insulation resistance. To avoid risks due to insulating breakout. £ 200,80 £ 200,80

EL-50794 Warning Signs 1 High Voltage Disabling/Enabling Warning Signs. £ 30,00 £ 30,00

VAT1 VAT1 Voltage Absence Detector 1 VAT1 is a bipolar voltage sensor. Needed to check the absence of voltage during the switch-off procedure ofElectric/Hybrid Vehicles. £ 144,90 £ 144,90

WE160002A GME lift table 30 40 84 2 IIThis lifting table is the basis for all newly developed Opel/Vauxhall Powertrain special service tools, and is needed to remove and re-install the Engines, Transmissions, HV-Batteries and Chassis components. Please order at Blitz Rotary.

N.A. N.A.

£ 1.075,20


List price (for sum up

purpose, repeated tools

excluded)

Electric Vehicle

G

roup

N

ew G

loba

l Lab

our C

ode

S

tand

ing

Ord

er C

lass

S

ervi

ce L

evel

Purpose of Tool

Gra

ndla

nd X

- H

ybrid

Cor

sa-F

- B

EV


0348-N 0348-N Installation sleeve E 14.3 2 II To overhaul the wheelhub and bearing of the frontaxle. £ 69,70 £ 69,70

0562-DZ 0562-DZ Special bolts E 30.1 2 II Tool is required to remove and install the wheelhub of the rearaxle. £ 69,20 £ 69,20

0631-J 0631-J Installation sleeve E 30.1 2 II This tool is required to remove and install both rubber bushings (front & rear) of the front lower control arm. £ 22,60 £ 22,60

0631-K 0631-K Removal tool E 30.1 2 II This tool is required to remove and install both rubber bushings (front & rear) of the front lower control arm. £ 24,20 £ 24,20

0631-L 0631-L Installation sleeve E 30.1 2 II This tool is required to remove and install both rubber bushings (front & rear) of the front lower control arm. £ 22,10 £ 22,10

0631-M 0631-M Removal / Installation tool E 30.1 2 II This tool is required to remove and install both rubber bushings (front & rear) of the front lower control arm. £ 19,40 £ 19,40

8601-T-C2 8601-T-C2 Socket E 14.3 2 II To overhaul the wheelhub and bearing of the frontaxle. £ 163,00 £ 163,00

BO-48871 Hull extraxctor cigarette lighter C 2 II Remove hull extraxtor cigarette lighter / Power outlet from instrument panel. £ 42,90 £ 42,90

BO-49380 Adjusting Tool C 2R II To adjust nozzle attitude at the front screen £ 12,30 £ 12,30

BO-50512 Radio Remoaval Tool N 2 II To remove Bosch Radio MMC £ 17,30 £ 17,30

BO-52590 1382 Unlocking Tool, Front Seat Belt Buckle C 64.4 2 II To separate the fastening strand from the belt buckle. £ 16,80 £ 16,80

CH-37287-1A-EU Adapter, fuel pressure testing 3/8'' L 40.2 2 IIAdapter for connection to the 3/8'' fuel line quick connectors.Used with EN-34730-91. £ 124,70 £ 124,70

CH-42188-B Ball Joint Seperator E 80.3 2 II CH-42188-B (J-42188-B) is required to separate the upper and lower ball joints as well as the tie rod ends. £ 113,20 £ 113,20

CH-48373 Mounting Engine/Gearbox/Front Axle

E J K

2 II To remove/install and fix engine/transmission and front axle,used with CH-904 and lifting device. £ 842,80 £ 842,80

CH-48373-200 Adapter for CH-48373E J K

2 II Remove/install and fix Engine/Transmission and Front Axle, used with CH-48373, CH-904 and lifting device. £ 171,20 £ 171,20

CH-48373-250 Adapter for CH-48373 J 2 II Remove/install and support engine.Used with CH-48373, CH-48373-300, CH-904 and lifting device. £ 15,70 £ 15,70

CH-48373-300 Adapter for CH-48373 J 2 II Remove/install and/ or position transmission.Used with CH-48373, CH-48373-250, CH-904 and lifting device. £ 113,90 £ 113,90

CH-48373-350 Adapter for CH-48373 J K 84.4 2 IIRemove/install and fix engine / transmission and front axle.Used with CH-48373, CH-904 and lifting device. £ 49,50 £ 49,50

CH-48373-400 Adapter for CH-48373 J K 84.4 2 IIRemove/install and fix engine / transmission and front axle.Used with CH-48373, CH-904 and lifting device. £ 72,50 £ 72,50

CH-48373-450 Adapter for CH-48373 J K 84.4 2 IIRemove/install and fix engine / transmission and front axle. Used with CH-48373, KM-904 and lifting device. £ 78,20 £ 78,20

Purpose of Tool

Passenger Car, SUV

G

roup

N

ew G

loba

l Lab

our C

ode

S

tand

ing

Ord

er C

lass

S

ervi

ce L

evel

A

dam

A

stra

-J

Ast

ra-K

C

orsa

-E

Cro

ssla

nd X

G

rand

land

X

Ins

igni

a

Ins

igni

a-B


List price (for sum up purpose, repeated tools

excluded)

K

arl

M

eriv

a-B

M

okka

Z

afira

-B

Zaf

ira-C

Z

afira

-Life

CH-48373-500 Adapter for CH-48373 J 40.6 2 II Support for LE1, used with CH-48373. £ 49,30 £ 49,30

CH-48482 Fuel Pump Locking Ring Remover/Installer L 2 II CH-48482 is used to remove and install the secondary fuel sender lock ring. £ 86,80 £ 86,80

CH-49289 Centering Adapter

E J K M

2 II Removing/installing front axle and adjust to the under carriage, used with CH-904 and lifting device. £ 1.059,60 £ 1.059,60

CH-49289-200 Adapter Kit for CH-49289 E 2 II Removing/Installing front axle, used with CH-49289, CH-904 and lifting device. Also used for engine removal with CH-49290. £ 357,40 £ 357,40

CH-49289-400 Adapter for CH-49289

E (J K M)

14.3 2 II Removing/Installing front axle, used with CH-49289, CH-904 and lifting device. £ 196,00 £ 196,00

CH-49289-450 Adapter for CH-49289

E (J K M)

14.3 2 II Remove/installing front axle, used with CH-49289, CH-49289-200, CH-904 and lifting device £ 136,50 £ 136,50

CH-49289-500 Adapter for CH-49289 - Centering Adapter 14,3 2 IIRemove/Install front axle,used with CH-49289, CH-49289-200, CH-904 and lifting device. £ 139,80 £ 139,80

CH-49290 Engine Support Tool J K 2 IIAdjusting engine to sub frame for work at engine control side, used with CH-904 and hydraulik lifter, and removing/installing the engine/transmission, and fixing to subframe used with CH 49289 CH 904 and lifting device

£ 918,90 £ 918,90

CH-49290-150 Orange Adapter

E J K M

2 II To support the oil pan. £ 71,70 £ 71,70

CH-49290-200 Adapter Kit for CH-49290 J 2 II Adjusting engine/transmission to subframe for work at engine control side and engine removal, used with CH-49289, CH-904 and lifting device. £ 435,50 £ 435,50

CH-49290-350 Adapter to CH-49290 J 2 II

1. Adjusting/ fixing engine/ transmission to subframe to work at engine control side (used with CH-49290) 2. Removing/installing the engine/transmission fixed to the subframe. (used with CH-49289, CH-49290, CH-904 and lifting device).

£ 38,70 £ 38,70

CH-49290-400 Adapter Kit to CH-49290 J K

40.6, 84.4, 84.6

2 IIAdjusting engine/transmission to subframe for work at engine control on engine control side and lifting device, and removing/installing the engine/transmission with fixing to subframe.

£ 345,70 £ 345,70

CH-49290-450 Adapter Kit to CH-49290 J K

40.6 84.4 84.6

2 IIEngine Support, used with Adapter EN-47650-320, Retainer Frame EN-47650, Engine Bridge EN-47649 (or MKM-883-1-A), Special Built Base EN-47649-100 and Front Adapter EN-47650-250.

£ 253,50 £ 253,50

CH-49290-500 Adapter Kit to CH-49290 - Engine / Transmission holder

40.6 84.4 84.6

2 II

Adjusting engine/transmission to subframe for work at engine controlon engine control side. Used with CH-49290, CH-49290-150, CH-904and lifting device, as well as removing/installing the engine/transmissionwith fixing to subframe used with CH-49289, CH-49289-200,CH-49289-500, CH-49290, CH-49290-150, CH-904 and lifting device.

£ 454,70 £ 454,70

CH-49376 Wrench E F 2 II Hold the wheel hub, for dismantling tightening the locking nut of the drive shaft. £ 81,80 £ 81,80

CH-49400 Remover, wheel hub & driveshaftE F 2 II To remove drive shaft from wheel flange £ 91,10 £ 91,10

CH-50093 Presstool E 2 II Remove revolte joint bolts at Hiper strut £ 18,00 £ 18,00

CH-50094 Remover Support bearing E 2 II Remove support bearing of steering knuckle at Hiper Strut, used with KM-161-B £ 23,80 £ 23,80

CH-50559 Front Hub/Bearing Remover/Installer kit E 2 IIUsed to remove and install the front hub bearing and race from the wheel hub assembly. £ 154,30 £ 154,30

CH-50571 Front Axle remover / Installer M 2 II To remove / install steering rod £ 50,30 £ 50,30

CH-50823 Support bearing remover E 2 II Remove upper ball joint from steering knuckle/HiperStrut £ 91,20 £ 91,20

CH-51034 Cradle Alignment Guide Pin E 2 II Used to install the cradle assembly to body as guide £ 21,90 £ 21,90

CH-51036-OPE RDM Cross-member Bushing Remover/Installer F 2 II Used to install and remove the rear drive module (RDM) bushings. £ 91,20 £ 91,20

CH-51095 Rear Shock Absorber Nut Remover / InstallerE F 2 II Used to install/remove the strut nut of rear shock absorber £ 32,90 £ 32,90

CH-52268 Fuel Pressure Measurement Tool Adapter L 40.2 2 IIAdapter between Fuel Pressure Test Tool and Fuel Pressure Measuring Port low pressure side (infront of high pressure pump). Used with: KM-J-34730-91 £ 8,80 £ 8,80

CH-52269 Fuel Pressure Gauge Adapter L 40.2 2 IIAdapter between Opel/Vx Fuel Pressure Gauge CH-37287-1A-EU and Fuel Rail and In-Tank Fuel Pump Hose. Used with CH-37287-1A-EU. £ 43,30 £ 43,30

CH-52288 0818-Z Brake Pedal Booster Rod Remover E 14.3 2 IIThis Tool is needed to disconnect the brake booster rod fromthe breake pedal. £ 21,60 £ 21,60

CH-52289 0721-B Steering Rack Locking Tool E 14.3 2 IIThis Tool is needed to support the ball joint of the steering gear duringintermediate shaft removal. Design of the steering gear requires that toavoid damages within the steering gear.

£ 212,20 £ 212,20

CH-52290 Hub and Bearing Installer E 14.3 2 II This Tool-Set is needed remove and install the wheel bearing and hub. £ 429,80 £ 429,80

CH-52291 6310-T1 Wheel Hub Holder E 14.3 2 II This Holder is needed to hold the wheel hub during hub nut removal. £ 144,60 £ 144,60

CH-52292 Axle Bushing Installer E 14.3 2 II This Tool-Set is needed to install the rear axle bushings into the axle,used with CH-51036. £ 81,40 £ 81,40

CH-52293 Fuel Pump Locking Ring Remover / Installer E 14.3 2 IIRemoving of fuel pump module lockring. Needed to gain access tothe fuel pump module and the fuel level sensor. £ 129,10 £ 129,10

CH-52423 Coolant Funnel 40.3 2 II Coolant Funnel is used to increas the coolant level above the highest point of the heater core, during static filling of the coolant system. £ 60,70 £ 60,70

CH-52540 0925 Strut upper centering device E 30.1 2 II This tool is required to engage the front strut in the inner wheelhousing during installation. £ 20,20 £ 20,20

CH-52541 Lower control arm overhaul-Kit E 30.1 2 IIThis tool is required to remove and install both rubber bushings (front & rear) of the front lower control arm. £ 193,00 £ 193,00

CH-52587 Prop Shaft Checking Gauge K 30.2 2 IIGauges are needed to finally check prop shaft position and secure safe fixation to PTU and RDM after removal and reinstallation. One for front end of prop shaft (connection to PTU) and one for rear end of prop shaft (connection to RDM).

£ 29,30 £ 29,30

CH-6002-600 Adapter for CH-6002-A F 30.3 2 II Remove / Install rear axle £ 104,60 £ 104,60

CH-6314-250 Adapter Rear Axle E F 2 II To remove/install and adjust rear axle under carriage. £ 300,20 £ 300,20

CH-904 Basic Frame E F 2 II Removing/installing various vehicle components with additional adapters. £ 132,20 £ 132,20

DT-50092 Pliers for clamp E 2 II Install clamps(new special Oetiker-clamp) for axle sleeves. £ 102,30 £ 102,30

DT-50186 Wheel Hub Holding Tool E 30.4 2 II To hold the wheel hub to remove and intall the drive axleshaft nut. £ 68,10 £ 68,10

DT-50188 Hub Spindle Remover E 30.4 2 II To remove the drive axleshaft from wheel hub. £ 79,10 £ 79,10

DT-50768 Seal Installer K 2 II DT-50768 is required for a new excluder seal on Graziano PTUs used on Opel Insignia MY2012. £ 75,60 £ 75,60

DT-50937 Seal Protector, Intermediate Drive Shaft K 2 IIDT-50937 is used to protect the transfer case Intermediate Drive Shaft (IDS) seal from the splines on the IDS during shaft removal or installation. £ 30,40 £ 30,40

DT-51329-A-GMG Drive Shaft Remover 84,2 2 II

Driveshafts on upcoming AWD vehicles are retained by a retaining clip inside the splines, which locks onto the PTU or RDM splined shaft. In order to overcome the retaining ring, a large force must be applied against it suddenly. DT-51329-A will fit multiple applications, and can provide a surface to hammer against if the slide hammer cannot unseat the snap ring. May replace previous prop shaft removers.

£ 59,00 £ 59,00

DT-52166 0346-AE Gauge, gear selection lever positioning K 84.4 2 II Is required to adjust the shift actuation (6 speed) £ 8,80 £ 8,80

DT-52171 0317-U Fitting Drift K 84.4 2 II To install the sealing of the right drive shaft £ 24,80 £ 24,80

DT-52186 0317-AQ Lipped Seal Extractor K 84.4 2 II De-/instalment of distance plate bushes £ 32,50 £ 32,50

DT-52188 0346-AB Selection shaft immobilisation pin K 84.4 2 II Is required to fixate the shifter shaft £ 13,50 £ 13,50

DT-52197 0317-T Fitting Drift K 84.4 2 II To install the sealing of the left drive shaft £ 23,30 £ 23,30

DT-52201 0317-TBD Gauge, gear selection lever positioning K 84.4 2 II To adjust the shift actuation (5-speed) £ 12,90 £ 12,90

DT-52211 0336-2A Drive Shaft Seal Ring Installer K 84.4 2 IIIs required for the assemble of the sealing ring between automatic transmission and drive shaft. £ 27,90 £ 27,90

DT-52212 0336-2B Drive Shaft Seal Ring Installer K 84.4 2 IIIs required for the assemble of the sealing ring between automatic transmission and drive shaft. £ 29,10 £ 29,10

DT-52213 0336-W Seal Ring Guide K 84.4 2 II Is required to avoid damaging the sealing ring when mounting the axle shaft. The existing special tool for the Aisin Warner AW40 cannot be used. £ 36,70 £ 36,70

DT-52214 0336-M Seal Ring Remover K 84.4 2 IITo de-install the sealing rings of the gear shift control of the automatic transmission. The existing special tool for the Aisin Warner AW40 cannot be used.

£ 76,30 £ 76,30

DT-52215 0336-N1 Seal Ring Installer K 84,4 2 II To install the sealing rings of the gear shift control of the automatic transmission.The existing special tool for the Aisin Warner AW40 cannot be used. £ 33,40 £ 33,40

DT-52216 0338-A Centering Adapter K 84,4 2 IIIs required for assembling the engine and the automatic transmission to centre the convertor on the driver disc. The existing special tool for the Aisin Warner AW40 cannot be used.

£ 68,00 £ 68,00

DT-52217 0336-2D Converter Holding Strap K 84,4 2 II Is required for the installation and de-installation of the automatic transmission. £ 10,80 £ 10,80

DT-52359 Differential seal fitting drift K 84.4 2 II Differential seal fitting drift, to install the differential seal on the left side. £ 29,90 £ 29,90

DT-52360 0332-B Differential seal fitting drift K 84.4 2 II Differential seal fitting drift, to install the differential seal on the right side £ 28,90 £ 28,90

DT-52465 0319-A Gauge K 84.4 2 II Gear selection lever positioning - size 1 £ 28,10 £ 28,10

DT-52466 0319 Gauge K 84.4 2 II Gear selection lever positioning - size 2 £ 28,10 £ 28,10

DT-52467 Gear Lever Positioning Tool K 84.7 2 II The Gear Lever Postioning Tool is to immobilise the selection shaft and to adjust the shift lever. £ 20,70 £ 20,70

DT-52514 0338-S Converter Holding Strap K 84.6 2 II The Converter Holding Strap is needed to secure the torque converter during removing/ installing the automatic transmission from / to the engine. £ 40,00 £ 40,00

DT-52515 0338-F Seal Ring Installer K 84.6 2 II The Seal Ring Installer is needed to install the shift shaft seal ring to the automatic transmissions. £ 50,60 £ 50,60

DT-52516 0336-U Drive Shaft Seal Ring Installer K 84.6 2 IIThe Drive Shaft Seal Ring Installer is needed to install the drive shaft seal ring (right side) of the automatic transmission. £ 52,50 £ 52,50

DT-52517 0336-V Drive Shaft Seal Ring Installer K 84.6 2 IIThe Drive Shaft Seal Ring Installer is needed to install the drive shaft seal ring of the automatic transmission. £ 53,10 £ 53,10

DT-52779 Gauge, Gear Selection Lever Positioning 2 II This tool is needed to adjust the gear selection shift lever. £ 16,40 £ 16,40

DT-6263-200 Clutch Pilot K 84.3 2 II Universal clutch pilot to center the clutch while installing, Used with DT-6263-A. £ 249,40 £ 249,40

DT-6263-A Clutch Remover/Installer K 2 II Remove and install the clutch £ 150,70 £ 150,70

DT-922-A Remover & Installer K 84.6 2 2 Remove & install of the torque converter £ 17,90 £ 17,90 EL-38125-38 Terminal Release Tool J 2 II Used to remove Tyco/Delphi DSQ 280 terminals from global epsilon wired fuse block. £ 27,70 £ 27,70 EL-38125-560-A Terminal Release Tool N 54.3 2 II To unlatch terminals in a connector housing. £ 24,60 £ 24,60

EL-38125-580 Kit, Terminal Release Tools N 2 II Required for new terminated lead service strategy £ 398,40 £ 398,40

EL-38125-EU Crimping Tool Wezag N 2 II A precise tool with three crimping profiles including splice connectors with four crimping profiles £ 189,10 £ 189,10

EL-50334-50 Infotainment Diagnostic KIT N 2 II To pinpoint vehicle component failures within the vehicle Infotainment system £ 60,70 £ 60,70

EL-52513 Release Tool, Airbag Connector N 64.5 2 IITo loosen/disconnect the connector of passenger airbag. Loosening is necessary for diagnosis of wiring harness/airbag functionality and removal operation of instrument panel/wiring harness.

£ 41,80 £ 41,80

EL-52554 Release Tool, Airbag ConnectorCN

64.5 54.3 2 II This tool is necessary to loosen/disconnect the connector of passenger airbag . £ 39,40 £ 39,40

EN-47650 Retainer Frame J 2 II To hold engine, used with vehicle specific adapter as EN-47650-100 Zafira-B, engine bridge EN-47649 (or MKM-883-1-A) and special feet EN-47649-100. £ 869,30 £ 869,30

EN-47650-250 Front Adapter to EN-47650 J 2 II To hold engine, used with EN-47650, EN-47650-300, EN-47649 und EN-47649-100 £ 167,00 £ 167,00

EN-47650-300 Rear Adapter to EN-47650 J 2 II To hold engine, used with EN-47650, EN-47650-250, EN-47649 and EN-47649-100 £ 296,60 £ 296,60

EN-47650-310 Engine Bridge retainer FrameE J K

2 II To hold the rear adapter EN-47650-300 with vehicle specific applications £ 9,50 £ 9,50

EN-47650-320 Fixing pin for EN-47650-300 J 2 II Fix the rear adapter EN-47650-300 to wheelhouse, used with Retainer Frame EN-47650 £ 20,80 £ 20,80

EN-47650-350 Adapter to EN-47650E J K

2 IISupport the Powertrain, used with Adapter EN-47650-320, Retainer Frame EN-47650, Engine Bridge EN-47649 (or MKM-883-a-A), Special Built Base EN-47649-100 and Front Adapter EN-47650-250

£ 180,60 £ 180,60

EN-47650-450 Adapter to EN-47650 E J 40.6 2 IIEngine Support, used with Adapter EN-47650-320, Retainer Frame EN-47650, Engine Bridge EN-47649 (or MKM-883-1-A), Special Built Base EN-47649-100 £ 161,00 £ 161,00

EN-47650-500 Adapter for EN-47650 (Fixture Retainer Frame) J 40.6 2 II Tool support, used with EN-47650 £ 24,80 £ 24,80

EN-47650-70 Engine Bridge retainer Frame E J 2 II Replacement of the long end pieces P-0094-1003 on Retainer Frame £ 56,00 £ 56,00

EN-49202 Rem - Drive Axle Shift E 30.4 2 II To remove drive axle shift £ 40,50 £ 40,50

EN-50422-EU AdBlue - Diagnostics Kit L 1 IWith this SCR-Diagnostic Kit the operating fluid of SCR-Systems, the functionality of the whole SCR-System and the functionality of the SCR-Dosing valve can be tested & verified

£ 142,30 £ 142,30

EN-50791-100-EU Adapter for EN-50791 J 40,6 2 2 Tool is used to install the fuel injector clamp. In conjunction with EN-50791. £ 8,40 £ 8,40

EN-50956 GR-6 Arnold Drive Bit J 40.6 2 II .25'' Hex bit x 25mm long with male LOCTE #6 driver configuration on one end. £ 24,30 £ 24,30

EN-51429 Engine lift brackets J 2 II Used to lift the LGE engines with and without transmission. £ 43,60 £ 43,60

EN-51698 Engine lift bracket J 40.6 2 II 3rd engine lift bracket to be added to L5Q engine in case of repair operations to be performed on transmission side (e.g. clutch repair etc.). £ 21,90 £ 21,90

EN-51848 Engine Support Tool J 40.6 2 II To support engine in vehicle, when removing/loosening the engine mount on timing side. £ 113,00 £ 113,00

EN-51878 Compression and Cylinder Leakdown Test Adapter Kit J 40.2 2 IIUniversal adapter to check the engine compression and execute cylinder leak test. For all diesel engines. £ 517,70 £ 517,70

EN-51955-EU Injector Seal Protector Installer and Sizer J 40.6 2 II Tool is used to install seals at injectors without over-stretching. £ 117,70 £ 117,70

EN-52055 Powertrain R&R Adapter Toolkit J 40.6 2 II Powertrain remove and reinstall supports used with WE160002A lifting table. £ 289,30 £ 289,30

EN-52055-10 Addtional Adapter for Tool Kit EN-52055 J 40.6 2 IIAdapter to revome & reinstal powertrains with the WE160002A lifting table. Used with EN-52055. £ 41,30 £ 41,30

EN-52055-100 Lifting Table Adapter Engine R&R J 40.6 2 II To remove and reinstall the Powertrain unit used with the Global Lifting Table. £ 171,20 £ 171,20

EN-52061 Socket J 40.6 2 II To tighten tool EN-52135 and EN-52341 £ 19,70 £ 19,70

EN-52062 Oil pressure switch socket K 40.6 2 II To loosen/tighten oil pressure switch £ 26,80 £ 26,80

EN-52063 Charge air gauge J 40.6 2 II To measure turbo charge pressure £ 37,50 £ 37,50

EN-52112 Installer Stretchy Belt J 40.6 1 I To assemble the elastic water pump belt and the drive belt of the side aggregates in vehicles without A/C. £ 68,40 £ 68,40

EN-52127 0109-2 Camshaft Positioning Device J 40.6 2 II Is required to position the cam shaft and block the crankshaft. £ 101,90 £ 101,90

EN-52132 0109-4G Oil sump alignment plate J 40.6 2 II Is required to avoid the leaking of the liquid seal when mounting the oil sump. £ 32,90 £ 32,90

EN-52133 EB engine kit (sealing) J 40.6 2 II To mount the crankshaft sealing and the countershaft sealing lid. £ 80,20 £ 80,20

EN-52134 0171-2-G2 Sleeve,Turbo-Boost Pressure Check J 40.6 2 IIAdapter to check the boost pressure sensor or, resp., the boos pressure in connection with the EN-52063 pressure gauge. £ 84,20 £ 84,20

EN-52135 1503-N Adapter, oil pressure check J 40.6 2 II To measure the motor oil pressure in 1.2 gasoline and 1.6 turbo diesel engines. Used with KM-498-B oil pressure gauge. £ 41,50 £ 41,50

EN-52136 0194-X Remover, Gear High Pressure Pump J 40.6 2 II To demount the fuel high pressure pump drive pulley in 1.6 diesel engines. £ 36,50 £ 36,50

EN-52137 0194-B Pin, Camshaft Setting J 40.6 2 II Is required to fixate the camshaft in valve timing position (e.g. when replacing the drive pulley) for 1.6 diesel engines. £ 36,50 £ 36,50

EN-52138 0194-C Pin, Flywheel J 40.6 2 II Is required to block the crankshaft (e.g. to loosen/tighten the screws of the drive belt disc or the double-mass flywheel). £ 35,40 £ 35,40

EN-52139 0194-D Lever, tensioner accessory drive belt J 40.6 1 ILever to untighten the drive belt tensioner for 1.6 and 2.0 diesel engines. Used with EN-52140. £ 66,60 £ 66,60

EN-52140 01099 Adapter, Lever- accessory belt tensioner J 40.6 1 IAdapter to untighten the drive belt tensioner for 1.6 and 2.0 diesel engines. Used with EN-52139. £ 88,20 £ 88,20

EN-52141 0194-F Pin, Tightener Accessory Drive Belt J 40.6 1 I Rig pin to secure the drive belt tensioner in untightened position. £ 16,40 £ 16,40

EN-52142 0194-J Pin, High Pressure Pump J 40.6 2 II Is required to fixate the fuel high pressure shaft in the specified position (e.g. when replacing the drive pulley) for 1.6 diesel engines. £ 21,50 £ 21,50

EN-52143 0194-K Installer, seal ring- camshaft J 40.6 2 II Is required to mount the cam shaft sealing ring. £ 38,00 £ 38,00

EN-52144 0194-L Installer, seal ring- crankshaft J 40.6 2 II Is required to mount the crankshaft sealing ring on the control side. £ 31,10 £ 31,10

EN-52145 0194-M (ohne -M2) Installer, seal ring- crankshaft J 40.6 2 II To mount the crankshaft sealing ring on the transmission side. £ 148,10 £ 148,10

EN-52146 0194-N Centering Pin, Camshaft Carrier J 40.6 2 II To align the camshaft carrier with the cylinder head. £ 52,10 £ 52,10

EN-52149 0185 Socket, Bolt-Cylinder Head J 40.6 2 II Is required to loose and tighten the cylinder head screws. £ 65,60 £ 65,60

EN-52151 0171-G4 Sleeve,Turbo-Boost Pressure Check J 40.6 2 II Adapter to check the boost pressure sensor or, resp., the boost pressure. £ 44,40 £ 44,40

EN-52202 0197-H Seal Fitting Tool J 40.6 2 II Is required to mount and calibrate the fuel injector sealing rings. £ 19,60 £ 19,60

EN-52203 0109-4A Socket, Bolt-Cylinder Head J 40.6 2 II Is required to loosen and tighten the cylinder head screws. £ 46,00 £ 46,00

EN-52204 0193-A Remover, Exhaust clips J 40.6 2 II To mount/dismount V-clips, especially in places that are difficult to reach. £ 94,60 £ 94,60

EN-52205 0194-W Locking Tool J 40.6 2 II To hold the respective pistons in position when checking the compression pressure. £ 54,40 £ 54,40

EN-52206 0153-Q Lever, cylinder head release J 40.6 2 II Lever to tilt the cylinder head away from the motor block. £ 58,70 £ 58,70

EN-52207 0194-2C Extractor J 40.6 2 IITo remove the injector sealing rings, if they (after the injectors have been dismounted) remained in the the injector chamber. For all common diesel injector seals.

£ 48,20 £ 48,20

EN-52208 0194-2D Cleaning Tool J 40.6 2 II To remove e.g. carbon deposits on the diesel injector sealing ring position. £ 30,70 £ 30,70

EN-52209 0199-G Camshaft gear immobilisation tool J 40.6 2 II To block the camshaft when loosening/tightening the drive pulley. £ 34,00 £ 34,00

EN-52210 1603-3 Socket, open end ring J 40.6 2 II Is required to loosen/tighten the union nut of the high pressure fuel line on the common rail for installed motors. £ 36,50 £ 36,50

EN-52331 Fitting drift, camshaft seal J 40.6 2 II To install camshaft seal £ 48,70 £ 48,70

EN-52332 Fitting Mandrel, crankshaft seal ring J 40.6 2 II To install the crankshaft seals on timing and transmission side £ 48,70 £ 48,70

EN-52333 0188-F Flywheel Stop J 40.6 1 I To block the flywheel / crankshaft £ 24,50 £ 24,50

EN-52334 0188-Y Setting peg, camshaft gear J 40.6 1 I Peg to get the crankshaft in the defined position for engine timing when replacing the timing belt £ 33,40 £ 33,40

EN-52335 0188-H Setting Peg, injection pump J 40.6 2 II Peg to get the camshaft in the defined position for HP fuelpump R&R £ 10,80 £ 10,80

EN-52336 0188-AH Pulley centering tool J 40.6 1 I Centralize the drive belt gear on the crankshaft when installing the timing belt £ 20,90 £ 20,90

EN-52337 0188-AD Cambelt retain clip J 40.6 1 I Fixes the timing belt on the camshaft gear when installing the timing belt £ 42,80 £ 42,80

EN-52339 Injection kit Diesel J 40.6 2 II Kit to remove Diesel injectors, HP fuel pump gear and to install the pump seals £ 128,00 £ 128,00

EN-52340 1621-C3 Extractor, High-pressure pump pinion J 40.6 2 IIThis tool is needed to remove the pinion of the HP fuel pump. Used with EN-52339. £ 56,00 £ 56,00

EN-52341 1503-2A Adapter, Oil Pressure J 40.6 2 II To check the oil pressure of the engine £ 40,60 £ 40,60

EN-52345 0197 Engine repair tool box J 40.6 2 II To overhaul engine, to fix camshaft position, to install crankshaft seal and support timing chain. £ 273,70 £ 273,70

EN-52345-100 Camshafts positioning tools J 40.6 2 II Additional adaptors for the blocking of the camshaft to repair the variable valve lift system, used with: EN-52345. £ 137,00 £ 137,00

EN-52346 Engine Overhaul Kit J 40.6 2 II To overhaul the engine, fix camshaft position, install crankshaft seal and support the timing chain £ 74,90 £ 74,90

EN-52347 1376 Inclinometer J 40.6 2 II The EL-52347 tool (3) is used to align the fastening plate, which the radar module (2) is attached to. £ 76,00 £ 76,00

EN-52348 0197-3A Camshaft Retaining Tool J 40.6 2 II To hold the camshafts in position when remove / install the bearing half shells. £ 63,20 £ 63,20

EN-52350 0171-2-G1 Checking Sleeve, Engine Charge Pressure J 40.6 2 II To check the turbo charge air pressure. £ 86,10 £ 86,10

EN-52432 Front Cover Seal Installer 40,6 2 2 Engine front cover seal installer is needed to mount the front cover and seal crankshaft and guided to the engine block. £ 21,20 £ 21,20

EN-52433 Injector Remover 40,6 2 2 Remove the Injector.Used with EN-51146-1-3 (Sliding hammer) £ 17,30 £ 17,30

EN-52434 Rear Cover Seal Installer 40,6 2 2 Engine rear cover seal installer is needed to mount the rear cover and seal proper and guided to the engine block. £ 39,90 £ 39,90

EN-52436-EU Timing Chain Tensioner Retention Tool J 40.6 2 II This tool is needed to hold the timing chain tensioner in position. £ 64,40 £ 64,40

EN-52437 Engine Lift Brackets J 40,6 2 2 Lifting and lowering the engine (with and without transmisson). Used with EN-47649. £ 123,50 £ 123,50

EN-52438 Torque Multiplayer J 40.6 2 II To loosen the fastener on the TVD, Wheel Hub, Transmission Flange Drive Shaft in conjunction; used with EN-52438-100; EN-52438-200, EN-52438-300. £ 276,60 £ 276,60

EN-52438-100 Holder Torque Multipier J 40.6 2 II To loosen the fastener on the TVD, Wheel Hub, Transmission Flange Drive Shaft in conjunction, used with EN-52438, EN-52438-200, EN-52438-300. £ 59,80 £ 59,80

EN-52438-200 Holder Torque Multipier J 40.6 2 II To loosen the fastener on the TVD, Wheel Hub, Transmission Flange Drive Shaft in conjunction, used with EN-52438, EN-52438-100, EN-52438-300. £ 29,00 £ 29,00

EN-52438-300 Rotational Angle Indicator J 40.6 2 II To loosen the fastener on the TVD, Wheel Hub, Transmission Flange Drive Shaft, used with EN-52438, EN-52438-100, EN-52438-200. £ 20,20 £ 20,20

EN-52438-400 Pins for EN-52438 J 40.6 2 II To loosen the fastener on the TVD (Torsion Vibration Damper), used with EN-52438, EN-52438-100 & EN-52438-200. £ 16,50 £ 16,50

EN-52439-EU Rear seal installer pilot J 40,6 2 2 Engine rear cover seal installer is needed to mount the rear cover and seal proper and guided to the engine block. £ 37,70 £ 37,70

EN-52440-EU Front seal installer pilot J 40,6 2 2 Engine front cover seal installer is needed to mount the front cover and seal crankshaft and guided to the engine block. £ 16,40 £ 16,40

EN-52441 Balance Shaft Timing Tool J 40,6 2 2 The balance shaft unit has to be fixed in the correct position. This new tool holds the balance shaft in position during removal and installation process. £ 14,30 £ 14,30

EN-52442 Balance Shaft Holding Tool J 40,6 2 2 This tool holds both balance shafts in position in order to remove the balance shaft cover and the oil pump. £ 17,00 £ 17,00

EN-52443 HP Fuel Pump Alignment Tool 40,2 2 2To install the HP fuel pump stress free the flat surface on the camshaft must be in the correct position.Side 1 is for the 50T & 45T, Side 2 is for the Prime & 675T.

£ 9,70 £ 9,70

EN-52454 Engine Lift Hook 40,6 2 2 Lifting and lowering the engine (with and without transmisson).Used with EN-47649 £ 37,10 £ 37,10

EN-52455 Open End Wrench (to adjust Camshaft) 40,6 2 2 Special open end wrench for turning and aligning the camshafts. £ 20,10 £ 20,10

EN-52457 Camshaft Locking Tool J 40,6 2 2 To lock the camshafts. £ 87,30 £ 87,30

EN-52458 VCP Holding Tool 40,6 2 2 Camshaft holding tool is needed to counterhold the VCP´s when torqued down. £ 93,00 £ 93,00

EN-52461-100-EU Adapter, Cam Phaser Torque Reaction Tool J 40,6 2 2 For counterholding VCP's, used with: EN-52461. £ 34,30 £ 34,30

EN-52461-300-EU Adapter and Retainer, Camshaft J 40,6 2 2To counter holding the VCP´s when torquing them down. used with: EN-52461-EU. £ 96,50 £ 96,50

EN-52461-EU Cam Phaser Torque Reaction Tool 40,6 2 2

Holding tool is necessary for counter holding the VCP's when torquing them down during the removal and installation process.The tool ensure an secure counterholding of the VCP's without any damage and hold the VCP's in position.

£ 74,00 £ 74,00

EN-52462-A-EU Camshaft Holder J 40.6 2 II To remove the camshaft sprockets as well as the camshaft housing incl.camshafts and it will hold the camshafts in timing position. £ 103,50 £ 103,50

EN-52463 Crankshaft Positioning Tool J 40,6 2 2 Positiontool to find timing position , TDC of each cylinder and lock the crankshaftin timing or TDC position. £ 96,10 £ 96,10

EN-52476 Flywheel Lock and Alignment Tool 40,6 2 2This tool is needed to lock the flywheel / crankshaft in TDC position and lock in flywheel while losen and tighten crankshaft screw. £ 80,40 £ 80,40

EN-52483-EU Guide Pins J 40,6 2 2

The front and rear crankshaft seals are part of the front and rear covers, and are not serviced separately- ONE Time use. The covers must be installed squarely to prevent damaging the sealant (RTV) or removing sealant (Smearing of Bead before compression) from the cover and allowing it to enter the engine. EN-52483 guide pins are screwed into two of the cover bolt holes, and keep the cover straight as it is installed into position. Tool also serve as guide on Plastic Oil Pan installation for proper alignment during oil pan installtion both on and off vehicle.

£ 6,80 £ 6,80

EN-52484-EU Camshaft Locking Tool J 40,6 2 2 Tool to lock camshaft in position. £ 33,70 £ 33,70

EN-52487-EU Balance Shaft Weight Holder J 40,6 2 2 Balance Shaft Weight Holder £ 34,70 £ 34,70

EN-52527-EU Oil Pump Sprocket Spanner J 40.6 2 II To hold the oil pump sprocket, to torque the bolt. £ 18,10 £ 18,10

EN-52588 0197-N Flywheel Setting Peg J 40.6 2 II Tool is used to fix the crankshaft in predefined position. £ 15,20 £ 15,20

EN-52767 Locking Pin J 40.6 2 II Pin to lock the secondary timing chain tensioner for service operations at the engine timing components £ 5,30 £ 5,30

EN-52768 Bracket, fixation, balancer shaft J 40.6 2 IIBracket to fixate the balance shaft in engine timing postion for service operations at the engine timing components. £ 18,00 £ 18,00

EN-52770 Bracket, fixation, balancer shaft J 40,6 2 2Bracket to hold the camshafts incl. ladderframe down on the cylinderhead duringbolting off/on the bearing caps. £ 147,70 £ 147,70

EN-52776 Guide, Seal Ring Radial, rear J 40,6 2 2 Guiding Tool for crankshaft radial seal ring rear. £ 31,70 £ 31,70

EN-52777 Guide, Seal Ring Radial, front J 40,6 2 2 Guiding Tool for crankshaft radial seal ring front. £ 20,90 £ 20,90

EN-52778 Guide Pin, engine cover, Front & Rear J 40,6 2 2Guide Pins for accurate installation of engine cover (front & Rear) with crankshaft radial seal ring (front & rear) to engine block. £ 6,30 £ 6,30

EN-52780 Bracket, fixation, balancer shaft J 40.6 2 IIBracket to fixate the balance shaft in engine timing postion for tighten/ loosen the balance shaft bolt - from transmission side. £ 20,30 £ 20,30

EN-52781 Engine lift brackets J 40,6 2 2 Brackets to hold the engine in place during transmission replacement and works at the engine mount. £ 51,10 £ 51,10

EN-52782 Engine Lift Brackets J 40,6 2 2 Lifting and lowering the engine (with and without transmisson). Used with EN-47649. £ 51,00 £ 51,00

EN-52783 Crankshaft rotating tool J 40,6 2 2 Tool to rotate the crankshaft during works on the engine timing regarding the tight environment conditions on vehicle. £ 11,60 £ 11,60

EN-52809 Timingbelt Check Gauge J 40.6 1 I Tool to check the width of EB2 engine timing belt. Timing belt is running in engine oil an seems to swell. £ 11,00 £ 11,00

EN-52894 Engine Lift Brackets J 40,6 2 2 Lifting and lowering the engine (with and without transmisson). Used with EN-47649 £ 25,70 £ 25,70

GE-41415-50A Fuel Tank Cap Adapter L 1 I Engine controls and fuel-testing for fuelsystem leaks £ 75,40 £ 75,40

GE-52531 Triangle Nut J 40.4 2 II This tool is required to unscrew the nut and replace the Capacitor of the start-stop system. £ 15,70 £ 15,70

J-35616-F J-35616-F - Terminal Probe Kit N 2 II For a faster, safer and more convenient way to conduct circuitry testing £ 382,30 £ 382,30

J-42183 Driver Handle K 2 II DT-42183 is a universal driver handle with a threaded end hat is very short for access in tight areas. To be used with DT-50768 £ 38,20 £ 38,20

KM-161-B Bearing Puller F J 1A IITo remove the taper bearing inner ring of the differential. To remove crank shaft drive pulley. £ 85,50 £ 85,50

KM-313-50Adapter for Drive Shaft remover DT-51329-A and Sliding Hammer KM-313

2 II Adapter to use with sliding hammer KM-313 and DT-51329-A £ 11,50 £ 11,50

KM-468-D Holding Wrench E 1 II To counter hold the front wheel flange £ 35,40 £ 35,40

KM-498-B Fluid Pressure Gauge J K 2 ITo check engine oil pressure, as well as to check transmission oil pressure, all engines OHC/DOHC, all AT-/AF13/14/20/30/33-/AR25/35 Transmission £ 87,20 £ 87,20

KM-586 Remover Hook 2 II Torque Converter Case Seal Ring Remover. Used with KM-J-7004 £ 72,30 £ 72,30 KM-6007-50 Adapter H 2R II To reset rear brake caliper piston, used with KM-6007-B £ 22,40 £ 22,40 KM-6007-B Reset Tool H 2 II Brake calliper piston, rear, replacing brake linings £ 78,10 £ 78,10 KM-796-A Remover L 1 II Quick fittings, fuel line £ 10,40 £ 10,40 KM-807 Plugs L 1 I Sealing opened quick fittings, petrol line £ 15,20 £ 15,20 KM-J-34730-91 Fuel Pressure Gauge L 2 II To check fuel pressure £ 118,90 £ 118,90

£ 20.655,00


CH-37287-1A-EU Adapter, fuel pressure testing 3/8'' L 40.2 2 II Adapter for connection to the 3/8'' fuel line quick connectors.Used with EN-34730-91. £ 124,70

CH-52268 Fuel Pressure Measurement Tool Adapter L 40.2 2 IIAdapter between Fuel Pressure Test Tool and Fuel Pressure Measuring Port low pressure side (infront of high pressure pump). Used with: KM-J-34730-91

£ 8,80

CH-52269 Fuel Pressure Gauge Adapter L 40.2 2 IIAdapter between OV Fuel Pressure Gauge CH-37287-1A-EU and Fuel Rail and In-Tank Fuel Pump Hose. Used with CH-37287-1A-EU

£ 43,30

CH-52423 Coolant Funnel 40.3 2 IICoolant Funnel is used to increas the coolant level above the highest point of the heater core, during static filling of the coolant system.

£ 60,70

CH-52540 0925 Strut upper centering device E 30.1 2 II This tool is required to engage the front strut in the inner wheelhousing during installation. £ 20,20

CH-52541 Lower control arm overhaul-Kit E 30.1 2 II This tool is required to remove and install both rubber bushings (front & rear) of the front lower control arm. £ 193,00

DT-52467 Gear Lever Positioning Tool K 84.7 2 II The Gear Lever Postioning Tool is to immobilise the selection shaft and to adjust the shift lever. £ 20,70

DT-52514 0338-S Converter Holding Strap K 84.6 2 IIThe Converter Holding Strap is needed to secure the torque converter during removing/ installing the automatic transmission from / to the engine.

£ 40,00

DT-52515 0338-F Seal Ring Installer K 84.6 2 II The Seal Ring Installer is needed to install the shift shaft seal ring to the automatic transmissions. £ 50,60

DT-52516 0336-U Drive Shaft Seal Ring Installer K 84.6 2 II The Drive Shaft Seal Ring Installer is needed to install the drive shaft seal ring (right side) of the automatic transmission. £ 52,50

DT-52517 0336-V Drive Shaft Seal Ring Installer K 84.6 2 II The Drive Shaft Seal Ring Installer is needed to install the drive shaft seal ring of the automatic transmission. £ 53,10

DT-6263-200 Clutch Pilot K 84.3 2 II Universal clutch pilot to center the clutch while installing, Used with DT-6263-A. £ 249,40

EN-41816 Crankshaft Balance Puller J 2 II J-41816 is used to remove the crankshaft balancer. £ 137,40 £ 137,40 EN-44226 Crankshaft Balancer Remover J 40.6 2 II Remove Crankshaft Balancer £ 141,50 £ 141,50

EN-44226-5 Adapter for EN-44226 J 40.6 2 II Protects the crankshaft end when using J-44226 to remove the SGE balancer £ 12,90 £ 12,90

EN-47971 Oil Pressure Gauge Adapter J 2 II EN-47971 is installed in place of the spin-on oil filter. £ 33,30 £ 33,30

EN-48034 Balance Installer J 2 II EN-48034 is used to install the crankshaft balancer onto the engine. £ 27,50 £ 27,50

EN-48383 Fixing Tool J 2 II To fix camshafts for control and adjustment the valve timing. Replaced EN-46105-EU £ 11,90 £ 11,90

EN-48589-A Socket Wrench J 2 II To rotate crankshaft £ 49,70 £ 49,70

EN-49074 Compressor-Universal Valve Spring J 2 II Used for tensioning valve springs - on and off vehicle. £ 160,70 £ 160,70

EN-49155 Locking Pin J 2 II Adapter used with EN-49074-Valve Spring Compressor. For pressing down the valve spring during valve service. £ 34,10 £ 34,10

EN-49212 Locking Tool J 2 IIHold the camshafts sprockets for checking and adjusting valve times. Fixing chain sprockets, camshafts, to check and adjust timing

£ 64,80 £ 64,80

EN-49245 Seal Installer and Sizer J 2 II EN-49245 must be used to install the seals correctly and to ensure they are sized correctly for leak-free operation. £ 51,00 £ 51,00

L

SY

B

14

XEL

Purpose of Tool

Petrol Engine: Pass. Car,SUV

G

roup

N

ew G

loba

l Lab

our C

ode

S

tand

ing

Ord

er C

lass

S

ervi

ce L

evel

A

14

NET

A

14

NFL

B

10

XE

B 1

0 XF

L

B 1

0 XF

T

B 1

0 XL

B

11

XE

L

IH




A

14

NFT

A

14

XFR

B

14

EL

B 1

4 XE

2

0 LG

E

A 2

8 N

ET

1.2

(LEG

)

1

.2 (L

EZ)

1

.6T

(LH

I)

1

.2 (L

ES)

B

14

XFL

A

16

XHT

B

14X

FT

L

3T

EN-49248 Fuel Rail Assembly Remover J 2 IIThe hand wheels on EN-49248 at each mount location are tightened evenly to un-seat all injectors evenly, preventing damage to the injectors, cylinder head, and rail mount assemblies.

£ 69,40 £ 69,40

EN-49940 Remover Quick-Connector J 2 II To remove Quick-Connector att coolant turbo charger £ 14,00 £ 14,00

EN-49942 Holding Wrench J 2 II To hold the turbocharger cooling water pipe during loosening/tightening £ 31,10 £ 31,10

EN-49977 Fixation sensor disc/camshaft J 2 II Adjusting, examining tax times with camshaft adjustment £ 103,90 £ 103,90

EN-49980 Guide Pins J 2 II To guide oil pan when installing £ 19,60 £ 19,60

EN-50513 Locking Pin J 2 II Lock the timing chain tensioner. £ 7,80 £ 7,80

EN-50656 Timing Chain Retainer J 2 II EN-50656 maintains timing chain tension and position during service. £ 34,00 £ 34,00

EN-50790 Fuel Pump Installation Gauge J 2 IIEN-50790 is used to verify that the camshaft fuel pump lobe is at the base circle position before installing the high pressure fuel pump on LGE.

£ 11,30 £ 11,30

EN-50791 Installer, Fuel Injection to Rail J 2 II EN-50791 holds the injector in position to allow the retaining clip to be removed or installed £ 41,30 £ 41,30

EN-50791-100-EU Adapter for EN-50791 J 40,6 2 2 Tool is used to install the fuel injector clamp. In conjunction with EN-50791. £ 8,40

EN-50792 Balancer Holder and Remover J 2 II EN-50792 installs in place of the starter, and engages the flywheel ring gear teeth to hold the flywheel and crankshaft for service. £ 113,20 £ 113,20

EN-50793 Camshaft Actuator Retainer J 2 IIEN-50793 engages the slots in the face of the actuator, and bolts to the cylinder head and cover to hold the actuator in position for the actuator bolt to be removed or installed.

£ 34,10 £ 34,10

EN-50820 Front Crankshaft Seal Installer J 2 II EN-50820 will install the front seal with the cover installed, or off the engine. £ 14,40 £ 14,40

EN-51146 Injektor remover and installer J 2 II Remove and install injector and fuel rail assembly. £ 431,90 £ 431,90

EN-51146-100 Adapter to EN-51146 J 2 II Remove and install injector assembly SGE gasoline engines £ 60,90 £ 60,90

EN-51147 Crankshaft holding Tool J 2 II Hold the crankshaft de-coubler in place while loosening and tightening the fixing screw £ 72,50 £ 72,50

EN-51148 Camshaft Holding Tool J 2 II Fix the camshafts (intake/exhaust), for checking/positioning valve timing. £ 87,00 £ 87,00

EN-51149 Spark plug wrench J 2 II Remove and install spark plugs £ 29,70 £ 29,70

EN-51150 Compression Test Adapter J 2 IITest compression and pressure loss, as well as put on compressed air during the change of the valve stem seal with fitted cylinder head. Used with Motometer.

£ 52,60 £ 52,60

EN-51151 Seal Ring Installer Crankshaft (transmission side) J 2 II Install crankshaft seal ring on transmission side. £ 49,70 £ 49,70

EN-51152 Seal Ring Installer Crankshaft(timing side) J 2 II Install crankshaft seal ring on timing side. £ 21,90 £ 21,90

EN-51153 Set fixation clamps J 2 II Fix balancer shafts to secure timing position. £ 10,40 £ 10,40

EN-51298 Holding Tool J 2 II Holding balancer module shaft in position for loosening / tightening the balancer sprocket holding screw £ 41,90 £ 41,90

EN-51365 Gauge, Fuel Pump Installation J 2 IIVerifies cam fuel pump lobe is on base circle prior to high pressurefuel pump installation. Avoids damage to HP fuel pump plunger. Valid for SGE engines with SIDI injection

£ 10,90 £ 10,90

EN-51367 Holder, Camshaft J 2 IIHolding the cams against spring pressure when setting base engine timing by engaging the hex on both the intake and exhaust camshafts. Allows servicing the actuator bolts

£ 31,10 £ 31,10

EN-51368 Installer, Front Crank Seal J 2 II Installs front crankshaft seal into timing cover, with both on-vehicle and unit repair applications preferred £ 99,20 £ 99,20

EN-51369 Installer, Rear Crank Seal J 2 II Install rear crank seal (Transmission side) £ 95,70 £ 95,70 EN-51397 Retainer, Timing Chain J 2 II Clamps timing chain while engine repair £ 93,20 £ 93,20

EN-51511 Injector Port Service Plug J 40.6 2 II Closing the injector bore for compression and pressure drop test. £ 28,20 £ 28,20

EN-51632 Camshaft Retainer J 40.6 2 II Fixing the camshafts to check / set valve timing and release / tighten the camshafts sprockets retaining screws. £ 57,50 £ 57,50

EN-51691 Timing Chain Retainer J 40.6 2 II Clamps timing chain while servicing camshaft actuators. £ 101,20 £ 101,20

EN-52055 Powertrain R&R Adapter Toolkit J 40.6 2 II Powertrain remove and reinstall supports used with WE160002A lifting table. £ 289,30

EN-52055-10 Addtional Adapter for Tool Kit EN-52055 J 40.6 2 IIAdapter to revome & reinstal powertrains with the WE160002A lifting table. Used with EN-52055. £ 41,30

EN-52061 Socket J 40.6 2 II To tighten tool EN-52135 and EN-52341 £ 19,70 EN-52063 Charge air gauge J 40.6 2 II To measure turbo charge pressure £ 37,50

EN-52112 Installer Stretchy Belt J 40.6 1 I To assemble the elastic water pump belt and the drive belt of the side aggregates in vehicles without A/C. £ 68,40

EN-52127 0109-2 Camshaft Positioning Device J 40.6 2 II Is required to position the cam shaft and block the crankshaft. £ 101,90

EN-52132 0109-4G Oil sump alignment plate J 40.6 2 II Is required to avoid the leaking of the liquid seal when mounting the oil sump. £ 32,90

EN-52133 EB engine kit (sealing) J 40.6 2 II To mount the crankshaft sealing and the countershaft sealing lid. £ 80,20

EN-52134 0171-2-G2 Sleeve,Turbo-Boost Pressure Check J 40.6 2 II Adapter to check the boost pressure sensor or, resp., the boos pressure in connection with the EN-52063 pressure gauge. £ 84,20

EN-52135 1503-N Adapter, oil pressure check J 40.6 2 II To measure the motor oil pressure in 1.2 gasoline and 1.6 turbo diesel engines. Used with KM-498-B oil pressure gauge. £ 41,50

EN-52141 0194-F Pin, Tightener Accessory Drive Belt J 40.6 1 I Rig pin to secure the drive belt tensioner in untightened position. £ 16,40

EN-52202 0197-H Seal Fitting Tool J 40.6 2 II Is required to mount and calibrate the fuel injector sealing rings. £ 19,60

EN-52203 0109-4A Socket, Bolt-Cylinder Head J 40.6 2 II Is required to loosen and tighten the cylinder head screws. £ 46,00

EN-52204 0193-A Remover, Exhaust clips J 40.6 2 II To mount/dismount V-clips, especially in places that are difficult to reach. £ 94,60

EN-52345 Engine repair tool box J 40.6 2 II To overhaul engine, to fix camshaft position, to install crankshaft seal and support timing chain. £ 273,70

EN-52346 Engine Overhaul Kit J 40.6 2 II To overhaul the engine, fix camshaft position, install crankshaft seal and support the timing chain £ 74,90

EN-52347 1376 Inclinometer J 40.6 2 II The EL-52347 tool (3) is used to align the fastening plate, which the radar module (2) is attached to. £ 76,00

EN-52348 0197-3A Camshaft Retaining Tool J 40.6 2 II To hold the camshafts in position when remove / install the bearing half shells. £ 63,20

EN-52350 0171-2-G1 Checking Sleeve, Engine Charge Pressure J 40.6 2 II To check the turbo charge air pressure. £ 86,10

EN-52432 Front Cover Seal Installer 40,6 2 2 Engine front cover seal installer is needed to mount the front cover and seal crankshaft and guided to the engine block. £ 21,20

EN-52433 Injector Remover 40,6 2 2 Remove the Injector.Used with EN-51146-1-3 (Sliding hammer) £ 17,30

EN-52434 Rear Cover Seal Installer 40,6 2 2 Engine rear cover seal installer is needed to mount the rear cover and seal proper and guided to the engine block. £ 39,90

EN-52436-EU Timing Chain Tensioner Retention Tool J 40.6 2 II This tool is needed to hold the timing chain tensioner in position. £ 64,40

EN-52437 Engine Lift Brackets J 40,6 2 2 Lifting and lowering the engine (with and without transmisson). Used with EN-47649. £ 123,50

EN-52438 Torque Multiplayer J 40.6 2 IITo loosen the fastener on the TVD, Wheel Hub, Transmission Flange Drive Shaft in conjunction; used with EN-52438-100; EN-52438-200, EN-52438-300.

£ 276,60

EN-52438-100 Holder Torque Multipier J 40.6 2 IITo loosen the fastener on the TVD, Wheel Hub, Transmission Flange Drive Shaft in conjunction, used with EN-52438, EN-52438-200, EN-52438-300.

£ 59,80

EN-52438-200 Holder Torque Multipier J 40.6 2 IITo loosen the fastener on the TVD, Wheel Hub, Transmission Flange Drive Shaft in conjunction, used with EN-52438, EN-52438-100, EN-52438-300.

£ 29,00

EN-52438-300 Rotational Angle Indicator J 40.6 2 IITo loosen the fastener on the TVD, Wheel Hub, Transmission Flange Drive Shaft, used with EN-52438, EN-52438-100, EN-52438-200.

£ 20,20

EN-52438-400 Pins for EN-52438 J 40.6 2 II To loosen the fastener on the TVD (Torsion Vibration Damper), used with EN-52438, EN-52438-100 & EN-52438-200. £ 16,50

EN-52439-EU Rear seal installer pilot J 40,6 2 2 Engine rear cover seal installer is needed to mount the rear cover and seal proper and guided to the engine block. £ 37,70

EN-52440-EU Front seal installer pilot J 40,6 2 2 Engine front cover seal installer is needed to mount the front cover and seal crankshaft and guided to the engine block. £ 16,40

EN-52441 Balance Shaft Timing Tool J 40,6 2 2The balance shaft unit has to be fixed in the correct position. This new tool holds the balance shaft in position during removal and installation process.

£ 14,30

EN-52442 Balance Shaft Holding Tool J 40,6 2 2 This tool holds both balance shafts in position in order to remove the balance shaft cover and the oil pump. £ 17,00

EN-52443 HP Fuel Pump Alignment Tool 40,2 2 2To install the HP fuel pump stress free the flat surface on the camshaft must be in the correct position.Side 1 is for the 50T & 45T, Side 2 is for the Prime & 675T.

£ 9,70

EN-52454 Engine Lift Hook 40,6 2 2 Lifting and lowering the engine (with and without transmisson).Used with EN-47649 £ 37,10

EN-52455 Open End Wrench (to adjust Camshaft) 40,6 2 2 Special open end wrench for turning and aligning the camshafts. £ 20,10

EN-52457 Camshaft Locking Tool J 40,6 2 2 To lock the camshafts. £ 87,30

EN-52458 VCP Holding Tool 40,6 2 2 Camshaft holding tool is needed to counterhold the VCP´s when torqued down. £ 93,00

EN-52461-100-EU Adapter, Cam Phaser Torque Reaction Tool J 40,6 2 2 For counterholding VCP's, used with: EN-52461. £ 34,30

EN-52461-300-EU Adapter and Retainer, Camshaft J 40,6 2 2 To counter holding the VCP´s when torquing them down. used with: EN-52461-EU. £ 96,50

EN-52461-EU Cam Phaser Torque Reaction Tool 40,6 2 2

Holding tool is necessary for counter holding the VCP's when torquing them down during the removal and installation process.The tool ensure an secure counterholding of the VCP's without any damage and hold the VCP's in position.

£ 74,00

EN-52462-A-EU Camshaft Holder J 40.6 2 IITo remove the camshaft sprockets as well as the camshaft housing incl.camshafts and it will hold the camshafts in timing position.

£ 103,50

EN-52463 Crankshaft Positioning Tool J 40,6 2 2 Positiontool to find timing position , TDC of each cylinder and lock the crankshaft in timing or TDC position. £ 96,10

EN-52476 Flywheel Lock and Alignment Tool 40,6 2 2 This tool is needed to lock the flywheel / crankshaft in TDC positionand lock in flywheel while losen and tighten crankshaft screw. £ 80,40

EN-52483-EU Guide Pins J 40,6 2 2

The front and rear crankshaft seals are part of the front and rear covers, and are not serviced separately- ONE Time use. The covers must be installed squarely to prevent damaging the sealant (RTV) or removing sealant (Smearing of Bead before compression) from the cover and allowing it to enter the engine. EN-52483 guide pins are screwed into two of the cover bolt holes, and keep the cover straight as it is installed into position. Tool also serve as guide on Plastic Oil Pan installation for proper alignment during oil pan installtion both on and off vehicle.

£ 6,80

EN-52484-EU Camshaft Locking Tool J 40,6 2 2 Tool to lock camshaft in position. £ 33,70 EN-52487-EU Balance Shaft Weight Holder J 40,6 2 2 Balance Shaft Weight Holder £ 34,70 EN-52527-EU Oil Pump Sprocket Spanner J 40.6 2 II To hold the oil pump sprocket, to torque the bolt. £ 18,10

EN-52894 Engine Lift Brackets J 40,6 2 2 Lifting and lowering the engine (with and without transmisson). Used with EN-47649 £ 25,70

GE-52531 Triangle Nut J 40.4 2 II This tool is required to unscrew the nut and replace the Capacitor of the start-stop system. £ 15,70

J-38758 Paraitic Graw Test Switch J 1 I Engine electrical-current drain diagnosis £ 45,30 £ 45,30 £ 2.639,70


L

SQ

CH-52540 0925 Strut upper centering device E 30.1 2 II This tool is required to engage the front strut in the inner wheelhousing during installation. £ 20,20

CH-52541 Lower control arm overhaul-Kit E 30.1 2 II This tool is required to remove and install both rubber bushings (front & rear) of the front lower control arm. £ 193,00

DT-52467 Gear Lever Positioning Tool K 84.7 2 II The Gear Lever Postioning Tool is to immobilise the selection shaft and to adjust the shift lever. £ 20,70

DT-52514 0338-S Converter Holding Strap K 84.6 2 II The Converter Holding Strap is needed to secure the torque converter during removing/ installing the automatic transmission from / to the engine. £ 40,00

DT-52515 0338-F Seal Ring Installer K 84.6 2 II The Seal Ring Installer is needed to install the shift shaft seal ring to the automatic transmissions. £ 50,60

DT-52516 0336-U Drive Shaft Seal Ring Installer K 84.6 2 II The Drive Shaft Seal Ring Installer is needed to install the drive shaft seal ring (right side) of the automatic transmission. £ 52,50

DT-52517 0336-V Drive Shaft Seal Ring Installer K 84.6 2 II The Drive Shaft Seal Ring Installer is needed to install the drive shaft seal ring of the automatic transmission. £ 53,10

DT-6263-90 Adapter basic holder K 2 II To loosen the clutch master cylinder piston rod from the clutch pedal.Used with: DT-6263-A £ 30,90 £ 30,90

EN-46782 Compression Adapter J 1 I To test compression, used with EN-46783 and MotoMeter £ 40,50 £ 40,50

EN-46783 Adapter J 1 I To test compression, used with EN-46782 £ 6,00 £ 6,00

EN-46791 Adapter J 1 I

To test compression, used with EN-46783 and MotoMeter. To test pressure loss used with EN-46783, as well as put on compressed air during the change of the valve stem sealing with fitted cylinder head used with EN-46783. Z19DT-engine

£ 12,10 £ 12,10

EN-47632 Cleaner J 1 I To clean injector pit £ 54,80 £ 54,80

EN-48303 Remover / Installer J 1 I To install / remove Fuel Filter Nut,used with EN-48304 £ 50,10 £ 50,10

EN-48304 Holder J 1 I To hold the Fuel Filter Housing,used with EN-48303 £ 36,00 £ 36,00

EN-49074 Compressor-Universal Valve Spring J 2 II Used for tensioning valve springs - on and off vehicle. £ 160,70

EN-49155 Adapter Valve Spring Compressing (for EN-49074) J 2 IIAdapter used with EN-49074-Valve Spring Compressor. For pressing down the valve spring during valve service. £ 34,10

EN-49377 Oil Retainer J 1 I Transfering the leakage oil when changing the oil filter £ 21,90 £ 21,90

EN-49826 Fixation tool J 2 II To fix and to block the high-pressure pumb sprocket. £ 34,20 £ 34,20

EN-49979 Crankshaft Holder J 2 II To hold shock mount at removing/installing center screwat the crankshaft. £ 88,30 £ 88,30

EN-49979-100 Adapter for EN-49979 J 2 II To hold the crankshaft balancer pulley during removal and installation of the fixing screws, used with EN-49979 £ 20,40 £ 20,40

EN-50885 High Pressure Pump Remover / Installer J 2 IIFix and hold timing chain sprocket together with timing chain in place during removal and installation of high pressure fuel pump. £ 212,00 £ 212,00

EN-51140 Cranshaft Holding Tool for MDE J 2 II Fix Crankshaft in TDC position £ 26,70 £ 26,70 EN-51141 Intermediate Drive Holding Tool J 2 II Fix intermediate drive gear during removal and installation. £ 65,20 £ 65,20 EN-51142 Oil Pump Sprocket Holding Tool J 2 II Hold oilpump sprocket and fix chain adjuster during removal and installation of oilpump £ 27,10 £ 27,10 EN-51143 Camshaft Fixing Tool for MDE J 2 II Fix camshaft in TDC position. £ 11,60 £ 11,60

EN-51144 Crankshaft Seal Installer Front Side J 2 II Installation of seal ring on transmission side of crankshaft, used with KM-523-1 £ 173,10 £ 173,10

A

20

DTR

Diesel Engine: Pass. Car SUV

G

roup

N

ew G

loba

l Lab

our C

ode

S

tand

ing

Ord

er C

lass

S

ervi

ce L

evel Purpose of Tool

1

6 M

DE

A

17

DTC

A

20

DTH

A

20

DTJ

A

20

DTL




2

.0T

(LC

I)

B

20

DTH

1

.5T

(LQ

P)

1.5

T (L

QJ)

1

.6T

(LFU

)

1.6

T (L

DI)

1

.6T

(LEK

)

L

XD

EN-51144-100 Adapter to EN-51144 J 2 II Install crankshaft seal (Front side), used with EN-51144 £ 29,10 £ 29,10

EN-51145 Crankshaft Seal Installer Transmission Side J 2 II Install seal ring crankshaft transmission side, used with KM-523-1 £ 35,50 £ 35,50

EN-51160 Injector Remover Installer J 2 II Remove and install injector, used with EN-51146-1-3 (Part of EN-51146) £ 36,50 £ 36,50

EN-51187 Injector Remover/Installer for MDE + LDE J 2 II Hold camshaft drive sprocket in position during removal and installation of camshafts. £ 33,20 £ 33,20

EN-51188 Cramshaft Sprocket Support J 2 II Hold camshaft drive sprocket in position during removal and installation of camshafts. £ 47,90 £ 47,90

EN-51383 Compression Adapter J 2 IITo measure the cylinder compression after removal of injectors of diesel engine if there are some symptoms – no easily engine start, low engine power, blowing blue smoke out of the tailpipe, losing lot of oil . Used with EN-50454 (Gauge assy).

£ 55,90 £ 55,90

EN-51411 Flywheel Holder J 40.6 2 II Locking the flywheel while transmission is mounted £ 71,10 £ 71,10

EN-51412 Fixing Tool J 40.6 2 II Locking the crankshaft / toothed belt pulley at TDC-position. £ 31,80 £ 31,80

EN-51413 Fixing and Aligning Tool J 40.6 2 II Fixing the high pressure pump sprocket to remove the high pressure pump (EN-51413-1) in conjunction with EN-51420. Aligning the high pressure pump sprocket to install the timing belt (EN-51413-2). £ 127,30 £ 127,30

EN-51414 Trigger Wheel Fixing Tool J 40.6 2 II Fixing the trigger wheel in TDC position. £ 9,90 £ 9,90

EN-51415 Camshafts Fixing Tool J 40.6 2 II Fixing the camshafts to check / set valve timing and release / tighten the camshafts sprockets retaining screws. £ 83,70 £ 83,70

EN-51416-A Balance Shaft Unit Fixing Tool J 40.6 2 II Fixing and holding the balance shaft unit. £ 95,50 £ 95,50

EN-51417 Trigger Wheel Holder J 40.6 2 II Counterholding the camshaft trigger wheel. £ 27,00 £ 27,00

EN-51418 Locking pin J 40.6 2 II Locking the timing chain tensioner. £ 10,90 £ 10,90

EN-51419 Lambda Sensor Socket SW22 J 40.6 2 II Removing / installing the oxygen sensor. £ 53,30 £ 53,30

EN-51420 Bead Breaker J 40.6 2 II Bead breaking the timing belt pulley from the high pressure pump. Used with fixing and adjustment tool EN-51413. £ 249,20 £ 249,20

EN-51421 Installer J 40.6 2 II Installing the camshafts oil seal rings of exhaust camshaft. £ 15,30 £ 15,30

EN-51585 High Pressure Pump Rotate Tool J 40.6 2 II Rotating the high pressure pump to installation position (OT position) before mounting. £ 23,90 £ 23,90

EN-51878 Compression and Cylinder Leakdown Test Adapter Kit J 40.2 2 II Universal adapter to check the engine compression and execute cylinder leak test. For all diesel engines. £ 517,70

EN-52055 Powertrain R&R Adapter Toolkit J 40.6 2 II Powertrain remove and reinstall supports used with WE160002A lifting table. £ 289,30

EN-52055-10 Addtional Adapter for Tool Kit EN-52055 J 40.6 2 II Adapter to revome & reinstal powertrains with the WE160002A lifting table. Used with EN-52055. £ 41,30

EN-52061 Socket J 40.6 2 II To tighten tool EN-52135 and EN-52341 £ 19,70

EN-52062 Oil pressure switch socket J 40.6 2 II To loosen/tighten oil pressure switch £ 26,80

EN-52063 Charge air gauge J 40.6 2 II To measure turbo charge pressure £ 37,50

EN-52135 1503-N Adapter, oil pressure check J 40.6 2 II To measure the motor oil pressure in 1.2 gasoline and 1.6 turbo diesel engines. Used with KM-498-B oil pressure gauge. £ 41,50

EN-52136 0194-X Remover, Gear High Pressure Pump J 40.6 2 II To demount the fuel high pressure pump drive pulley in 1.6 diesel engines. £ 36,50

EN-52137 0194-B Pin, Camshaft Setting J 40.6 2 II Is required to fixate the camshaft in valve timing position (e.g. when replacing the drive pulley) for 1.6 diesel engines. £ 36,50

EN-52138 0194-C Pin, Flywheel J 40.6 2 II Is required to block the crankshaft (e.g. to loosen/tighten the screws of the drive belt disc or the double-mass flywheel). £ 35,40

EN-52139 0194-D Lever, tensioner accessory drive belt J 40.6 1 I Lever to untighten the drive belt tensioner for 1.6 and 2.0 diesel engines. Used with EN-52140. £ 66,60

EN-52140 01099 Adapter, Lever- accessory belt tensioner J 40.6 1 I Adapter to untighten the drive belt tensioner for 1.6 and 2.0 diesel engines. Used with EN-52139. £ 88,20

EN-52141 0194-F Pin, Tightener Accessory Drive Belt J 40.6 1 I Rig pin to secure the drive belt tensioner in untightened position. £ 16,40

EN-52142 0194-J Pin, High Pressure Pump J 40.6 2 II Is required to fixate the fuel high pressure shaft in the specified position (e.g. when replacing the drive pulley) for 1.6 diesel engines. £ 21,50

EN-52143 0194-K Installer, seal ring- camshaft J 40.6 2 II Is required to mount the cam shaft sealing ring. £ 38,00 EN-52144 0194-L Installer, seal ring- crankshaft J 40.6 2 II Is required to mount the crankshaft sealing ring on the control side. £ 31,10

EN-52145 0194-M (ohne -M2) Installer, seal ring- crankshaft J 40.6 2 II To mount the crankshaft sealing ring on the transmission side. £ 148,10

EN-52146 0194-N Centering Pin, Camshaft Carrier J 40.6 2 II To align the camshaft carrier with the cylinder head. £ 52,10 EN-52149 0185 Socket, Bolt-Cylinder Head J 40.6 2 II Is required to loose and tighten the cylinder head screws. £ 65,60

EN-52151 0171-G4 Sleeve,Turbo-Boost Pressure Check J 40.6 2 II Adapter to check the boost pressure sensor or, resp., the boost pressure. £ 44,40

EN-52204 0193-A Remover, Exhaust clips J 40.6 2 II To mount/dismount V-clips, especially in places that are difficult to reach. £ 94,60

EN-52205 0194-W Locking Tool J 40.6 2 II To hold the respective pistons in position when checking the compression pressure. £ 54,40

EN-52206 0153-Q Lever, cylinder head release J 40.6 2 II Lever to tilt the cylinder head away from the motor block. £ 58,70

EN-52207 0194-2C Extractor J 40.6 2 II To remove the injector sealing rings, if they (after the injectors have been dismounted) remained in the the injector chamber. For all common diesel injector seals. £ 48,20

EN-52208 0194-2D Cleaning Tool J 40.6 2 II To remove e.g. carbon deposits on the diesel injector sealing ring position. £ 30,70

EN-52209 0199-G Camshaft gear immobilisation tool J 40.6 2 II To block the camshaft when loosening/tightening the drive pulley. £ 34,00

EN-52210 1603-3 Socket, open end ring J 40.6 2 II Is required to loosen/tighten the union nut of the high pressure fuel line on the common rail for installed motors. £ 36,50

EN-52331 Fitting drift, camshaft seal J 40.6 2 II To install camshaft seal £ 48,70

EN-52332 Fitting Mandrel, crankshaft seal ring J 40.6 2 II To install the crankshaft seals on timing and transmission side £ 48,70

EN-52333 0188-F Flywheel Stop J 40.6 1 I To block the flywheel / crankshaft £ 24,50

EN-52334 0188-Y Setting peg, camshaft gear J 40.6 1 I Peg to get the crankshaft in the defined position for engine timing when replacing the timing belt £ 33,40

EN-52335 0188-H Setting Peg, injection pump J 40.6 2 II Peg to get the camshaft in the defined position for HP fuelpump R&R £ 10,80

EN-52336 0188-AH Pulley centering tool J 40.6 1 I Centralize the drive belt gear on the crankshaft when installing the timing belt £ 20,90

EN-52337 0188-AD Cambelt retain clip J 40.6 1 I Fixes the timing belt on the camshaft gear when installing the timing belt £ 42,80

EN-52339 Injection kit Diesel J 40.6 2 II Kit to remove Diesel injectors, HP fuel pump gear and to install the pump seals £ 128,00

EN-52340 1621-C3 Extractor, High-pressure pump pinion J 40.6 2 II This tool is needed to remove the pinion of the HP fuel pump. Jused with EN-52339. £ 56,00

EN-52341 1503-2A Adapter, Oil Pressure J 40.6 2 II To check the oil pressure of the engine £ 40,60

EN-52345 Engine repair tool box J 40.6 2 II To overhaul engine, to fix camshaft position, to install crankshaft seal and support timing chain. £ 273,70

EN-52443 HP Fuel Pump Alignment Tool 40,2 2 2 To install the HP fuel pump stress free the flat surface on the camshaft must be in the correct position.Side 1 is for the 50T & 45T, Side 2 is for the Prime & 675T. £ 9,70

EN-52767 Locking Pin J 40.6 2 II Pin to lock the secondary timing chain tensioner for service operations at the engine timing components £ 5,30

EN-52768 Bracket, fixation, balancer shaft J 40.6 2 II Bracket to fixate the balance shaft in engine timing postion for service operations at the engine timing components. £ 18,00

EN-52770 Bracket, fixation, balancer shaft J 40,6 2 2 Bracket to hold the camshafts incl. ladderframe down on the cylinderhead during bolting off/on the bearing caps. £ 147,70

EN-52776 Guide, Seal Ring Radial, rear J 40,6 2 2 Guiding Tool for crankshaft radial seal ring rear. £ 31,70

EN-52777 Guide, Seal Ring Radial, front J 40,6 2 2 Guiding Tool for crankshaft radial seal ring front. £ 20,90

EN-52778 Guide Pin, engine cover, Front & Rear J 40,6 2 2Guide Pins for accurate installation of engine cover (front & Rear) with crankshaft radial seal ring (front & rear)to engine block. £ 6,30

EN-52780 Bracket, fixation, balancer shaft J 40.6 2 II Bracket to fixate the balance shaft in engine timing postion for tighten/ loosen the balance shaft bolt - from transmission side. £ 20,30

EN-52781 Engine lift brackets J 40,6 2 2 Brackets to hold the engine in place during transmission replacement and works at the engine mount. £ 51,10

EN-52782 Engine Lift Brackets J 40,6 2 2 Lifting and lowering the engine (with and without transmisson). Used with EN-47649. £ 51,00

EN-52783 Crankshaft rotating tool J 40,6 2 2 Tool to rotate the crankshaft during works on the engine timing regarding the tight environment conditions on vehicle. £ 11,60

GE-52531 Triangle Nut J 40.4 2 II This tool is required to unscrew the nut and replace the Capacitor of the start-stop system. £ 15,70

J-38758 Paraitic Graw Test Switch J 1 I Engine electrical-current drain diagnosis £ 45,30

KM-523-1 Handle J 2 II Install seal ring crankshaft transmission side, used with EN-51145 £ 16,30 £ 16,30

£ 1.964,20


DT-49112 SAT Anti Rotating Wedge K2 II

to fix SAT-Clutch (Valeo) for remove and install in order to prevent an automatic placing of the clutch. with A17DTR Engine.

£ 8,80 £ 8,80

DT-52166 0346-AE Gauge, gear selection lever positioning K 84.4 2 II Is required to adjust the shift actuation (6 speed) £ 8,80

DT-52171 0317-U Fitting Drift K 84.4 2 II To install the sealing of the right drive shaft £ 24,80

DT-52186 0317-AQ Lipped Seal Extractor K 84.4 2 II De-/instalment of distance plate bushes £ 32,50

DT-52188 0346-AB Selection shaft immobilisation pin K 84.4 2 II Is required to fixate the shifter shaft £ 13,50

DT-52197 0317-T Fitting Drift K 84.4 2 II To install the sealing of the left drive shaft £ 23,30

DT-52201 0317-TBD Gauge, gear selection lever positioning K 84.4 2 II To adjust the shift actuation (5-speed) £ 12,90

DT-52359 Differential seal fitting drift K 84.4 2 IIDifferential seal fitting drift, to install the differential seal on the left side. £ 29,90

DT-52360 0332-B Differential seal fitting drift K 84.4 2 IIDifferential seal fitting drift, to install the differential seal on the right side £ 28,90

DT-52465 0319-A Gauge K 84.4 2 II Gear selection lever positioning - size 1 £ 28,10

DT-52466 0319 Gauge K 84.4 2 II Gear selection lever positioning - size 2 £ 28,10

DT-6263-A Clutch Remover/Installer K 2 II Remove and install the clutch £ 150,70

KM-586 Remover Hook 2 II Torque Converter Case Seal Ring Remover. Used with KM-J-7004 £ 72,30

£ 8,80

F

40-6

CR

Manual Transmission:Pass. Car, SUV

G

roup

N

ew G

loba

l Lab

our C

ode

S

tand

ing

Ord

er C

lass

S

ervi

ce L

evel

Purpose of Tool

F

17-5

CR

F17

-5ER

F

17-5

WR

F

17-5

ER M

TA

F40

F

13-5

F

17-5

M

T-6

(M0L

)

F

40-6

WR

MT

20-6

MT

20-6

MTA

M

T 32

-6

MT

32-6

WR

D

33 (A

ntar

a)

D20

-5

MT-

5 (M

0C)

M

T-5

(M0K

)

MT-

5 (M

0E)

M

T-6

(M0D

)

M

32




M

T-6

(M0M

)

MT-

6 (M

0A)

M

T-6

(M0F

)


CH-52587 Prop Shaft Checking Gauge K 30.2 2 II

Gauges are needed to finally check prop shaft position and secure safe fixation to PTU and RDM after removal and reinstallation. One for front end of prop shaft (connection to PTU) and one for rear end of prop shaft (connection to RDM).

£ 29,30

DT-41229 Installer Shaft

ar minimum required special tools starter kit...

Documents