A© 2020 Riley Blake Designs. All Rights Reserved.

CANDY HEARTS TABLE RUNNER

CANDY HEARTS TABLE RUNNER

by Sandy Gervais

1© 2020 Riley Blake Designs. All Rights Reserved.

CANDY HEARTS TABLE RUNNER

Cream TextureCut 2 strips 5” x WOF. Sub-cut from strips: 16 - 5” squares (C)Cut 2 strips 31/2” x WOF for Top/Bottom Borders.Cut 2 strips 21/2” x WOF for Side Borders.Cut 1 strip 21/2” x WOF. Sub-cut from strip: 4 - 21/2” x 91/2” rectangles (E)Cut 2 strips 2” x WOF. Sub-cut from strips: 32 - 2” squares (D)

TABLE RUNNER ASSEMBLYRefer to the table runner photo and layout for the placement of prints.

General InstructionsAll angled pieces are constructed using the sew and flip method. This method is described below and referenced throughout the pattern.

Sew and Flip MethodPlace the 2 pieces right sides together matching the raw edges in one corner. Draw a diagonal line on the wrong side of the top piece across the corner. Sew on the drawn line. Trim the seam allowance above the sewn line to ¼”. Flip the top piece away from the bottom piece and press.

Heart Blocks (Make 8)Press the seam allowances open.

Select 2 A rectangles of the same color, 2 B squares of different colors, 2 C squares and 4 D squares.

Using the sew and flip method described in the general instructions, sew D squares to the upper corners of the A rectangles.

FINISHED TABLE RUNNER SIZE 24” x 44”Measurements include ¼” seam allowance.Sew with right sides together unless otherwise stated.

Please check our website www.rileyblakedesigns.com/ pattern-updates for any revisions before starting this project. This pattern requires a basic knowledge of quilting technique and terminology. The table runner and block diagrams portrayed are virtual images. The layout and look of your project may differ when using actual fabric.

FABRIC REQUIREMENTS1/2 yard Sweet Mint Texture (C610 Sweet Mint)* Fat 1/8 each of the following Texture prints: Glacier (C610 Glacier) Key Lime (C610 Key Lime) Shell (C610 Shell) Super Pink (C610 Super Pink) Violet (C610 Violet) Yellow (C610 Yellow)7/8 yard Cream Texture (C610 Cream)* Includes binding

CUTTING REQUIREMENTSPlease read instructions first before cutting. WOF - width of fabric.

Sweet Mint TextureCut 1 strip 5” x WOF. Sub-cut from strip: 4 - 5” x 91/2” rectangles (A)Cut 1 strip 21/2” x WOF. Sub-cut from strip: 3 - 21/2” squares (B)Cut 4 strips 21/4” x WOF for Binding.

Texture Fat 1/8’sCut the following from each Fat 1/8.Cut 1 strip 5” x 21”. Sub-cut from strip: 2 - 5” x 91/2” rectangles (A)Cut 1 strip 21/2” x 21”. Sub-cut from strip: 3 - 21/2” squares (B)Twenty one B squares are cut, but only twenty are used in the table runner. There will be one square left over A

D

2© 2020 Riley Blake Designs. All Rights Reserved.

CANDY HEARTS TABLE RUNNER

Repeat to sew a C square to the lower left corner of the first A rectangle and the lower right corner of the second A rectangle.

Sew the A rectangles together to make a Heart (91/2” x 91/2”).

Using the sew and flip method, sew the B squares to the lower corners of the Heart to complete 1 Heart Block (91/2” x 91/2”).

Repeat to make 8 Heart Blocks.

End Strip (Make 2)Press the seam allowances open.

Select 2 B squares of different colors and 2 E rectangles.

Using the sew and flip method, sew a B square to the lower right corner of 1 E rectangle.

Repeat to sew a B square to the lower left corner of the remaining E rectangle.

Sew the E rectangles together to complete 1 End Strip (21/2” x 181/2”).

Repeat to make 2 End Strips.

Table Runner CenterSew the 8 Heart Blocks together into 2 Rows of 4 Blocks, as shown in the Table Runner Layout Diagram. Press the seam allowances in opposite directions.

Sew the Rows together. Press the seam allowance open.

Sew an End Strip to the side edges of the Hearts to complete the Table Runner Center (181/2” x 401/2”). Press the seam allowance open.

BordersSeam allowances vary so measure through the center of the table runner before cutting border pieces.

Sew top and bottom borders (longest side) to the Table Runner Center first. Press seams towards borders. Top and Bottom borders should be 31/2” x 401/2”. Side borders should be 21/2” x 241/2”.

Finish table runner by layering the table runner top, batting, and back. Bind with the Sweet Mint Texture strips. Have fun with your colors and enjoy the journey of making your table runner.

A A

C C

Heart

B BHeart Block

BE

BE

End Strip

3© 2020 Riley Blake Designs. All Rights Reserved.

CANDY HEARTS TABLE RUNNER

Tabl

e Ru

nner

Lay

out D

iagr

am