description: san mateo bunk bed series...upper and lower bunk. size of mattress (for upper bunk,...
TRANSCRIPT
Size of Mattress (for UPPER Bunk, Twin)
SAFETY WARNING !
Replacement PartsReplacement parts, including additional guardrails, may be obtained from any of our (Westwood Design)dealers.
Replacement PartsKeep all instruction sheets for future reference to assemble bed for moving and/or different set up.
ASSEMBLY INSTRUCTIONS
Page 1 of 7
DESCRIPTION: SAN MATEO BUNK BED SERIES
MADE IN MALAYSIA
1. Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed.2. Always use the recommended size mattresses or mattress supports, or both, to help prevent the likelihood of entrapment or falls.3. Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.4. Do not allow children under 6 years of age to use the upper bunk.5. Prohibit more than one person on the upper bunk.6. Periodically check and ensure that the guardrail, ladder, and other components are in their proper position, free from damage, and that all connectors are tight.7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.8. Always use the ladder for entering and leaving the upper bunk.9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.10. Use of a night light may provide added safety precaution for a child using the upper bunk.11. Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and wall.12. The use of water or sleep flotation mattresses is prohibited.13. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example, but not limited to, hooks, belts and jump ropes.14. Keep these instructions for future reference.
This bed is designed to use a twin mattress 37.5” to 38.5” wide x 74” to 75” long with the total thicknessnot exceeding 8” for upper bunk. Do not use mattress without the proper slat system and properattachments described in the instructions. NOTE: there must be at least 5 inches from the topsurface of the mattress to top edge of guardrail.
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small Hardware which may have comeloose inside the carton during shipment.Identify and count all Hardware and compare with the Hardware List Below.
SAN MATEO TWIN OVER FULL BUNK BED
MADE IN MALAYSIA
ASSEMBLY INSTRUCTIONSSAN MATEO BUNK BED SERIES
Size of MattressThis bed is designed to use a twin mattress 37.5" to 38.5" wide x 74" to 75" long with the total thickness not exceeding 8" for upper and lower bunk.
Size of Mattress (for UPPER Bunk, Twin)This bed is designed to use a twin mattress 37.5" to 38.5" wide x 74" to 75" long with the total thickness not exceeding 8" for upper bunk.
Size of Mattress (for LOWER Bunk, Full)This bed is designed to use a full mattress 53.5" to 54" wide x 74" to 75" long with the total thickness not exceeding 8" for lower bunk.
SAN MATEO TWIN BUNK BED
Page 2 of 7
TOOLS REQUIRED (NOT PROVIDED)
PHILLIPS SCREWDRIVER
PART LIST
2 PCS
Qty.Description
2 PCS
Drawing
Twin Bunk Bottom
Bed Side Rails
Full Bed Slat 1 SET
HARDWARE LIST ( FOR TWIN AND FULL LOWER BUNK USE )
Qty.No. Description SizeDrawing
1
2
4 PCSMetal Dowel M10 x 100mm
HARDWARE LIST ( FOR GUARDRAIL AND LADDER USE )
Qty.No. Description SizeDrawing
Bolt M8 x 60 mm 6 PCS4
JCN Nut M8 x 20 mm
1 PC
5
M5
4 PCS
6
2 PCS
7
Allen Key
Bolt M8 x 25 mm
1 PCMetal Plate 120 x 25 x 3.5mm8
8 PCSScrew M4 x 16 mm9
Twin Bunk Top
Long Guard Rail 1 PC
Short Guard Rail 1 PC
Ladder 1 PC
4 PCS
ASSEMBLY INSTRUCTIONSDESCRIPTION: SAN MATEO BUNK BED SERIES
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small Hardware which may have comeloose inside the carton during shipment.Identify and count all Hardware and compare with the Hardware List Below.
26 PCSWood Screw M4 x 32 mm
HARDWARE LIST ( TWIN UPPER BUNK USE )
Qty.No. Description SizeDrawing
3 26 PCSWood Screw M4 x 32 mm
HARDWARE LIST ( FOR BED RAIL USE )
Qty.No. Description SizeDrawing
11
12
16 PCSBolt M8 x 100 mm
16 PCSBarrel Nut M8 x 16 mm
13 1 PCAllen Key M5
Full Bunk Bottom2 PCS
Twin Bed Slat 1 SET
No.
A
B
C
D
E
F
G
H
I
C
A
EI
DF
G
DI
B
A
GDF
MADE IN MALAYSIA
2 PCSScrew M4 x 20 mm10
Page 3 of 7
H
H
CAUTION: Do not attempt to movethe bed when fully assembled. Thiscould result in damage to the rails,headboard, or footboard.
ASSEMBLY INSTRUCTIONSFOR TWIN AND FULL LOWER BUNK ASSEMBLY
DESCRIPTION: SAN MATEO BUNK BED SERIES
12
11 13
A,B or C
Step 1
D or E
2 or 3
Step 2
MADE IN MALAYSIAPage 4 of 7
I
I
Assembly BED RAIL to the Headboard and Footboard for:* TWIN UPPER BUNK BED* TWIN LOWER BUNK BED* FULL LOWER BUNK BED
Assembly SLAT to the BUNK BED for:* TWIN UPPER BUNK BED* TWIN LOWER BUNK BED* FULL LOWER BUNK BED
Page 5 of 7
CAUTION: Do not attempt to movethe bed when fully assembled. Thiscould result in damage to the rails,headboard, or footboard.
ASSEMBLY INSTRUCTIONSFOR TWIN UPPER BUNK ASSEMBLY
DESCRIPTION: SAN MATEO BUNK BED SERIES
MADE IN MALAYSIA
64
75
9
76
6
F
G
A
Step 5
Step 6
Step 4
Step 3
Page 6 of 7
ASSEMBLY STEP TWIN BED TOP
TWIN OVER FULL BUNK BED
TWIN BUNK BED
MADE IN MALAYSIA
Step 7
ASSEMBLY INSTRUCTIONSDESCRIPTION: SAN MATEO BUNK BED SERIES
1
Page 7 of 7
ASSEMBLY STEPS BED LADDER
ASSEMBLY INSTRUCTIONS
DESCRIPTION: SAN MATEO BUNK BED SERIES
MADE IN MALAYSIA
Step 8
9
H
H
10
8
10
TWIN OVER FULL BUNK BED
TWIN BUNK BED