foampak technical data - viking group inc · the most remote riser by 20 to 30 psi (1.5 to 2 bar)....

1. SYSTEM NAME FoamPak A foam pump/pressure balancesystem complete with relief valveand pump controller, piped.2. MANUFACTURERTHE VIKING CORPORATION210 N. Industrial Park RoadHastings, Michigan 49058 U.S.A.Telephone: (269) 945-9501 (877) 384-5464Fax: (269) 945-9599e-mail: [email protected] Pump and Controller by:Edward’s Manufacturing Inc. 2441 SE Stubb StreetMilwaukie, Oregon 97222 U.S.A.3. PRODUCT DESCRIPTIONThe Viking FoamPak foam pumpsystem incorporates a UL Listed andFM Approved positive displacementbronze/stainless steel rotary gearfoam pump capable of dry operation.The balance valve, pressure reliefvalve, and piping products are allbronze or copper as standardmaterials. A UL Listed/FM Approvedlisted foam pump controller, mounted and wired, is included. The Viking FoamPak, is a completefoam pumping system, equipped with supply and discharge piping(excluding the foam supply pipingand foam return piping to the foamtank), auxiliary flushing connections,concentrate discharge check valve,pressure sustaining valve, pumpcasing relief valve, concentratesupply strainer, foam pump andpump controller.The rotary gear pump is of all bronzeconstruction (recommended), (optional ductile iron casing with bronze interiorparts or all stainless steel available), to withstand the corrosive atmospherethat exists with AFFF and AR-AFFFconcentrates. The unique lip sealconstruction of the pump allows it torun dry without damage to the pump.

The Viking FoamPak is to be usedanywhere a foam system that utilizespositive pressure proportioning (VikingLFF ILBP) is desired or necessary. The Viking FoamPak can supplysingle or multiple foam systems withbalanced pressure proportioning. 4. TECHNICAL DATA Listings and approvals:Controller – UL Listed and FM

ApprovedPump – UL Listed and FM Approved

(ISO Registered company)Connections: FoamPak 5S - 1 ½” (38mm)

Supply and Discharge 150 lb.Flanged connections

FoamPak 13S - 1 ½” (38mm)Supply and Discharge 150 lb.Flanged connections

FoamPak 26S - 2” (50mm) Supplyand Discharge 150 lb. Flangedconnections



Controller standard NEMA rating: NEMA 2 (IEC IP31 ), (otherNEMA enclosures for motor andcontroller are available atadditional cost.)

Controller and pump motor voltage: Low Voltage (3 phase/50, 60Hz/200-208 volt), voltages of220/230, 380/415, or 460/480 at50 or 60 Hz are available at noadditional cost but must bespecified when ordering.

Standard FoamPak Specifications Maximum Pump Speed: 1800 RPM 60 Hz/1500 RPM 50 HZMaximum viscosity of liquid to be

transferred: 3500 cps per UL/FM (5500 cps-non listed pumps)

Material Standards:See individual FoamPak charts for

material standards.

All Piping is Standard Copper orBrass. Optional StainlessSteel is available.

For options and detail partnumbers for ordering see Figure2.5. AVAILABILITY AND SERVICEThe Viking FoamPak foampumping systems are availablethrough a network of domestic,Canadian, and internationaldistributors. See The Viking Website for closest distributor orcontact The Viking Corporation.

6. GUARANTEES For details of warranty, refer toViking’s current list price schedule or contact The Viking Corporationdirectly. 7. APPLICATION The Viking FoamPak foampumping systems are foamconcentrate delivery devices. Viking FoamPak foam systemsare a critical part of a low expansion foam system which includes thefollowing applications: aircrafthangars, petro-chemical facilities,flammable and combustible liquidwarehouses, tank farms, facilities forbulk storage of flammable orcombustible liquids, offshoreFPSO and shipboard applications and military installations. TheFoamPak systems can supplyfoam concentrate to concentrateinjection piping run above orbelow ground. 8. OPERATION The Viking FoamPak pumpassembly is supplied with a pump

TECHNICAL DATAFOAMPAK

A FOAM PUMP/PRESSUREBALANCE AND RELIEF

VALVE/PUMP CONTROLLER

Foam 250 aFebruary 26, 2003

Form No. F_050399

Viking technical data may be found on The Viking Corporation’s Web site at

http://www.vikingcorp.com. The Web site may include a more recent

edition of this technical data page.

Replaces page 250a-o January 7, 2002. (Revised Pump SelectionChart to reflect 60 Hz and 50 Hz and updated area code.)

OBSOLETE

controller that starts the pump via aremote start signal when foamconcentrate is required to be pumped to the hazard area(s). There aremany methods of starting the foampump, the most common is through awater pressure switch at the systemriser. When the water pressureswitch is activated, the foam pumpcontroller will receive a signal to startoperation. Other methods include pressuredrop, which requires a maintenance(jockey) foam concentrate pump thatmaintains a desired pressure in thefoam concentrate piping. When thepressure drops in the concentratepiping to a point that the maintenance (jockey) foam concentrate pumpcannot maintain the desiredpressure, the main pump foampressure switch sends a signal andstarts the main foam pump. Maintenance (jockey) foamconcentrate pumps are not standardwith the Viking FoamPak, but can beordered as a separate option. The foam concentrate is supplied tothe Viking FoamPak assemblythrough a customer or contractorsupplied pipe, connected to anatmospheric storage tank. Theatmospheric storage tank can be ahorizontal or vertical vessel. Mostatmospheric foam storage tanks areof a fiberglass or poly construction. The foam concentrate storage tank isnot pressurized, the foam concentrate is only under atmospheric pressure tothe supply side of the VikingFoamPak.When the Viking FoamPak is notequipped with a maintenance(jockey) foam concentrate pump, thedischarge piping from the pump skidassembly to the In-Line BalancedProportioner (ILBP), is full of foamconcentrate, but not under pressure. When the pump controller receives asignal to start, the electric motor is

energized, driving the rotary gearpump. The pump draws foamconcentrate from the atmospherictank and discharges the concentratethrough the foam concentratedischarge piping network (installed bycontractor) to the ILBP(s). The VikingFoamPak assembly is equipped with a pressure sustaining valve that isconnected to a return line that is pipedto a return connection located on theatmospheric storage tank. The returnline connection should be locatedbelow the liquid level of the storagetank to minimize any foaming actioncaused by the agitation of the foamconcentrate. The pressure sustainingvalve is utilized to ensure the foamdischarge pressure is balanced withthe water pressure, regardless of thefoam usage requirement. Often thepump output exceeds the demand,thus using the pressure sustainingvalve to maintain the “balance”. The FoamPak is equipped with apump relief valve that is piped to theconcentrate return line past thepressure sustaining valve. The pumprelief valve is in place to ensure that aflow of foam concentrate is maintained through the foam pump even in apump churn condition (no concentratedemand) or sustaining valve failure. The pump relief valve will open at apre-set pressure and direct foamconcentrate back to the atmosphericstorage tank. The pump reliefvalve eliminates overheating and over-pressurization of the foampump and piping in a dead head(no flow) or churn pressurecondition. The Viking FoamPak is equipped withprimary and secondary supply anddischarge connections. The primarysupply connection is utilized to take asupply from the atmospheric storagetank, the secondary supply connection is utilized to supply the pump with anauxiliary source of foam concentrate if

needed or to supply the foampump, valves and piping withclean water if flushing is required. The primary discharge connection is utilized to supply theconcentrate piping to the ILBPpiping network. The secondarydischarge connection is utilized tosupply auxiliary foam concentrateusers or as a discharge outlet forflushing. The secondary supply anddischarge connections are supplied with quarter turn stainless steel orall bronze ball valves, (normallyclosed) to isolate theseconnections from normaloperating conditions. The supply connection isequipped with a “Y” strainer toensure that the foam concentrateor flushing supply entering thefoam pump is clean. 9. SELECTION The Viking FoamPak system isavailable in five basic sizes,available with four standard foamdischarge pressure ratings, 100,150, 200, 250 psi, (6.9, 10.3, 13.8,17.2 bar). The FoamPakassembly flow rate capacity isselected based on the requiredflow rate per minute of foamconcentrate and percentage offoam injection required for themost demanding hazard. Thestandard method of sizing theFoamPak capacity is bymultiplying the area of the hazardby the required density, multiplythat sum by the concentration offoam concentrate (1%, 3%, 6%),multiply that sum by a 1.15%safety factor for hydraulic overdischarge and hydraulic balancing of the system piping. If the hazardrequired flow rate is known,meaning the hydrauliccalculations for the hazard havebeen performed, multiply the total




Foam 250 b February 26, 2003

OBSOLETE

water flow in minutes by the % offoam to be used. The FoamPak assembly’s pressurerating is selected after considering thepressure differential requirements ofthe ILBP, (The Viking LLF, ILBPrequires a minimum pressuredifferential of 15 psi (1 Bar), added tothe static water pressure available atthe riser. The pressure rating of theFoamPak should be determined byadding in the pressure drop of theconcentrate discharge pipingattributed to the length of theconcentrate piping from theFoamPak discharge flange to themost remote ILBP. The typicalpressure rating of the system mayexceed the static water pressure tothe most remote riser by 20 to 30 psi(1.5 to 2 Bar). Select the next highest pressure rating pump. See Figure 1,page 880d for Pump Selection Chart.10. INSTALLATION The Viking FoamPak assembly issupplied by an atmospheric storagetank (supplied by contractor)connected to the supply flange of theskid assembly. The discharge flangeis connected to the concentratepiping supplying the proportioningdevices (ILBP’s), (concentrate pipingand ILBP’s installed by contractor). The foam pump controller and foampump motor are pre-wired on theskid. A power supply to the controlleris required. The proper voltage,hertz, and phase are critical factorsthat must be available as they werespecified upon ordering. Refer toController information on this datapage.The Viking FoamPak should beinstalled in accordance with NFPAstandards and local requirementsgoverning the installation of foamsystems.

11. TESTING AND MAINTENANCE It is imperative that the VikingFoamPak is inspected and tested perthe requirements of NFPA 20 andNFPA 25. This is the owner’sresponsibility. The concentrate pipingis to be hydrostatically tested asprescribed with NFPA. The pump skid assembly is to be flushed inaccordance with manufacturer’srecommendations. The supply “Y”strainer screen should be examinedand cleaned in accordance with NFPA 25, before each test. 12. FOAM PUMP CONTROLLER The foam controllers are designedspecifically for foam service and havethe following alarms and functions asstandard:

1. Phase failure / phase reversalalarm

2. Running period timer, factory setfor 10 minutes

3. Manual shut down only,emergency start pushbutton

4. Remote start terminal connection5. Deluge system starting contact6. Remote pump operating contact7. Remote power failure contact8. Start delay timer for a 2 pump

operation system, primary/standbyfoam pumps

9. Spare contacts for field wiring ofadditional pumps alarms

10. Configured for an optionalpressure proof switch, eithersupplied by the contractor orupon special order from Viking

11. V i s i b l e a l a rm – l owconcen t ra te l eve l

Typical alarm options that may beadded to the above at an additionalcost are:1. Anti condensation space heaters

for 120 volt or 240 volt, bothsingle phase

2. Foam pressure switch forloss of pressure automaticstarting

3. Automatic transfer switchesto transfer to another powersource

4. Audible and visible pump onremote alarm contact / locallight

FoamPak electrical details: 1. All of the foam pump

controllers are UL Listed andFM Approved.

2. All controllers are manufacturedspecifically for foam pumpservice.

3. All controllers are initiallyfigured for a start signal ordeluge signal startingmethod. If a pressure lossstart method is desired, afoam pressure proofingswitch must be provided toinitiate a “start signal” fromloss of pressure.

4. All controllers are priced for220/230, 380/415, 460/480 voltservice in either 50 Hz or 60 Hzservice. If voltages other thanthe ones shown above arerequired, please contactViking for a specificquotation.

5. All electric motor enclosuresare IP-54 or open drip prooftype. Many other motorenclosures are availablesuch as IP-55 (TEFC) andEEXD. Please contactViking with the specific motorenclosure required if otherthan ODP IP-54.

6. All foam pump controllersoffered are NEMA 2enclosure for protected areainstallations. Otherenclosure ratings areavailable such as NEMA 3R /4 / 4x. Consult Viking for




February 26, 2003 Foam 250 c

OBSOLETE




Foam 250 d February 26, 2003

Concentrate Discharge Horsepower VikingFlow Pressure Required Part No.

10 GPM (38 L/min) 100 PSIG (7 bar) 5 (4 kW) F01935A150 PSIG (10 bar) 5 (4 kW) F01936A

(See FoamPak 5S) 200 PSIG (14 bar) 5 (4 kW) F01937A250 PSIG (17 bar) 7.5 (5.6 kW) F01938A

25 GPM 95 L/min) 100 PSIG (7 bar) 3 (2.25 kW) F01939A150 PSIG (10 bar) 7.5 (5.6 kW) F01940A

(See FoamPak 5S) 200 PSIG (14 bar) 7.5 (5.6 kW) F01941A250 PSIG (17 bar) 10 (7.5 kW) F01942A

50 GPM (190 L/min) 100 PSIG (7 bar) 7.5 (5.6 kW) F019423A150 PSIG (10 bar) 10 (7.5 kW) F01944A

(See FoamPak 13S) 200 PSIG (14 bar) 10 (7.5 kW) F01945A250 PSIG (17 bar) 20 (15 kW) F01946A

75 GPM (284 L/min) 100 PSIG (7 bar) 15 (11.25 kW) F01947A150 PSIG (10 bar) 15 (11.25 kW) F01948A

(See FoamPak 26S) 200 PSIG (14 bar) 20 (15 kW) F01949A250 PSIG (17 bar) 25 (18.75 kW) F01950A

100 GPM (378 L/min) 100 PSIG (7 bar) 15 (11.25 kW) F01951A150 PSIG (10 bar) 20 (15 kW) F01952A


150 GPM (568 L/min) 100 PSIG (7 bar) 25 (18.75 kW) F01935A150 PSIG (10 bar) 30 (22.5 kW) F01956A



(See FoamPak 50S) 200 PSIG (14 bar) 50 (37.5 kW) F01961A250 PSIG (17 bar) 50 (37.5 kW) F01962A

250 GPM (946 L/min) 100 PSIG (7 bar) 40 (30 kW) F01963A150 PSIG (10 bar) 50 (37.5 kW) F01964A

(See FoamPak 50S) 200 PSIG (14 bar) 60 (45 kW) F01965A250 PSIG (17 bar) 60 (45 kW) F01966A







60 Hz PUMP SELECTION CHART

FIGURE 1

OBSOLETE




Concentrate Discharge Horsepower VikingFlow Pressure Required Part No.

10 GPM (38 L/min) 100 PSIG (7 bar) 3 (2 kW) F01935B150 PSIG (10 bar) 3 (2 kW) F01936B

(See FoamPak 5S) 200 PSIG (14 bar) 3 (2 kW) F01937B250 PSIG (17 bar) 5 (4 kW) F01938B

25 GPM 95 L/min) 100 PSIG (7 bar) 5 (4 kW) F01939B150 PSIG (10 bar) 5 (4 kW) F01940B

(See FoamPak 5S) 200 PSIG (14 bar) 7.5 (5.6 kW) F01941B250 PSIG (17 bar) 10 (7.5 kW) F01942B

50 GPM (190 L/min) 100 PSIG (7 bar) 10 (7.5 kW) F01943B150 PSIG (10 bar) 10 (7.5 kW) F01944B

(See FoamPak 13S) 200 PSIG (14 bar) 15 (11.25 kW) F01945B250 PSIG (17 bar) 15 (11.25 kW) F01946B

75 GPM (284 L/min) 100 PSIG (7 bar) 15 (11.25 kW) F01947B150 PSIG (10 bar) 15 (11.25 kW) F01948B

(See FoamPak 26S) 200 PSIG (14 bar) 20 (15 kW) F01949B250 PSIG (17 bar) 25 (18.75 kW) F01950B

100 GPM (378 L/min) 100 PSIG (7 bar) 15 (11.25 kW) F01951B150 PSIG (10 bar) 20 (15 kW) F01952B

(See FoamPak 26S) 200 PSIG (14 bar) 25 (18.75 kW) F01953B250 PSIG (17 bar) 25 (18.75 kW) F01954B

150 GPM (568 L/min) 100 PSIG (7 bar) 20 (15 kW) F01935B150 PSIG (10 bar) 30 (22.5 kW) F01956B

(See FoamPak 26S) 200 PSIG (14 bar) 40 (30 kW) F01957B250 PSIG (17 bar) 40 (30 kW) F01958B

200 GPM (757 L/min) 100 PSIG (7 bar) 25 (18.75 kW) F01959B150 PSIG (10 bar) 40 (30 kW) F01960B



(See FoamPak 50S) 200 PSIG (14 bar) 50 (37.5 kW) F01965B250 PSIG (17 bar) 60 (45 kW) F01966B




(See FoamPak 59S) 200 PSIG (14 bar) 75 (56.3 kW) F01973B250 PSIG (17 bar) 100 (75 kW) F01974B


(See FoamPak 59S) 200 PSIG (14 bar) 100 (75 kW) F01977B250 PSIG (17 bar) 100 (75 kW) Not available in 50 Hz

50 Hz PUMP SELECTION CHART

Foam 250 eFebruary 26, 2003

OBSOLETE

price addition. UL Listed andFM Approved controllers are not available in explosion proofenclosures.

7. Standard controller startingmethod is: Cross the line or fullvoltage. Other reduced voltageoptions such as Y-delta orsolid-state are available. Please contact Viking for a specificquote.

8. All connecting wiring from thecontroller to the electric motor iscomplete and to NEMAstandards.

9. Motor service factors aresometimes used on certain

FoamPak pressures and flowrates. Typically the electricmotors have a 15% servicefactor. 10% or less of the motorservice factor is used on someflow/pressure combinations.

FoamPaks with Diesel Engines Sometimes electrical service is notavailable or unreliable. If the hazardsite has questionable electricalconditions, a UL Listed and FMApproved low horsepower dieselengine pump driver is available. ULListed and FM Approved diesel enginemanufacturers are EMI-John Deere orEMI Isuzu.

Diesel powered FoamPak’s arecomplete assemblies similar tothe electrical operated units. Diesel engine packages arecompletely self contained exceptfor the battery charger powerrequirement of single phase,110/220 volt, 50/60 Hz.

Foam Tanks Foam tanks should be sized tosupply the FoamPak with enoughfoam concentrate to provide foamfor at least 10 minutes or longer,depending on the location, AHJand/or hazard and designrequirements.




Foam 250 f February 26, 2003

OBSOLETE

FOAMPAKA FOAM PUMP/PRESSURE

BALANCE AND RELIEFVALVE/PUMP CONTROLLER

TECHNICAL DATA

FOAMPAK 5SConcentrate Flow

10 and 25 GPM

February 26, 2003 Foam 250g

OBSOLETE

ITEMDISCHARGEPRESSURE

PSI

CONCENTRATEFLOW

PART NO.50 HZ

PART NO.60 HZ

DESCRIPTION QTY MATERIAL

100 10 GPM F02315 F02315 1 BRONZE

150 10 GPM F02315 F02315

200 10 GPM F02316 F02315

250 10 GPM F02331 F02330

100 25 GPM F02318 F02317

150 25 GPM F02318 F02318

200 25 GPM F02325 F02318

250 25 GPM F02340 F02332

100 10 GPM F02371 F02370 1 --

150 10 GPM F02371 F02373

200 10 GPM F02371 F02373

250 10 GPM F02372 F02373

100 25 GPM F02374 F02373

150 25 GPM F02374 F02375

200 25 GPM F02376 F02375

250 25 GPM F02378 F02377

100 10 GPM F02355 F02354 1 --

150 10 GPM F02355 F02356

200 10 GPM F02355 F02356

250 10 GPM F02357 F02356

100 25 GPM F02357 F02356

150 25 GPM F02357 F02358

200 25 GPM F02359 F02358

250 25 GPM F02361 F02360

4 -- -- -- -- 1" PRESSURE RELIEF VALVE (0260004) 1 BRONZE

5 -- -- -- -- 1-1/4" CLAVAL VALVE 1 BRONZE

6 -- -- COMPOUND GAUGE, 3-1/2", 0 TO 30 Hg. 1 STAINLESS STEEL

7 -- -- PRESSURE GAUGE, 3-1/2", 0 TO 300 PSI 1 STAINLESS STEEL

8 -- -- -- -- 1-1/2" BALL VALVE 2 BRONZE

9 -- -- -- -- 1-1/4" BALL VALVE 2 BRONZE

10 -- -- -- -- 1-1/2" SWING CHECK VALVE 1 BRONZE

11 -- -- -- -- 1-1/2" X 1-1/4" REDUCING PIPE TEE 1 BRONZE

12 -- -- -- -- 1-1/2" PIPE TEE 2 BRONZE

13 -- -- -- -- 1-1/4" 90° PIPE ELBOW 2 BRONZE

14 -- -- -- -- 1-1/4" CLASS 150 PIPE UNION 2 BRONZE

15 -- -- -- -- 1-1/2" SUCTION "Y" STRAINER 1 BRONZE

16 -- -- -- -- COUPLING GUARD BA-05-7.5 1 MILD STEEL

17 -- -- -- -- 1-1/2" 150# SCREW ON FLANGE 4 BRONZE

18 -- -- -- -- 1-1/4" 150# SCREW ON FLANGE 1 BRONZE

19 -- -- -- -- NAMEPLATE 1 MILD STEEL

20 -- -- -- -- 1-1/4" PIPE TEE 1 BRONZE

21 -- -- -- -- 1-1/4" PIPE CROSS 1 BRONZE

22 -- -- -- --1-1/4" HOSE X 9" LONG WITH BRONZEKING NIPPLE ONE END AND BRONZESWIVEL NIPPLE OPPOSITE END

1 --

23 -- -- -- -- 1-1/2" PIPE COUPLING 2 BRONZE

24 -- -- -- -- PANEL SUPPORT UPRIGHTS 2 MILD STEEL

25 -- -- -- -- 1-1/2" PIPE NIPPLES 1 LOT BRONZE

26 -- -- -- -- 1-1/4" PIPE NIPPLES 1 LOT BRONZE

27 -- -- -- -- PIPE SKID ASSEMBLY 1 MILD STEEL

3 EMI FTA-750 CONTROL PANEL

F02342 F02342

FOAMPAK 5S

1 EDWARDS MODEL 20-420 PUMP

MOTOR, 7.5 HP, 1800 RPM2



TECHNICAL DATA

Foam 250h February 26, 2003

OBSOLETE



TECHNICAL DATA


50 GPM

Foam 250iFebruary 26, 2003

OBSOLETE


PSI

CONCENTRATEFLOW

PART NO.50 HZ

PART NO.60 HZ


100 50 GPM F02327 F02326 1 BRONZE

150 50 GPM F02327 F02326

200 50 GPM F02327 F02326

250 50 GPM F02341 F02341

100 50 GPM F02378 F02375 1 --

150 50 GPM F02378 F02377

200 50 GPM F02380 F02377

250 50 GPM F02380 F02381

3 -- -- -- -- 1-1/2" PRESSURE RELIEF VALVE 1 BRONZE


5 -- -- VAC. GAUGE, 3-1/2", 0 TO 30 Hg. 1 STAINLESS STEEL


7 -- -- -- --

8 -- -- -- -- 1-1/2" 150# SCREWED FLANGE 5 BRONZE

9 -- -- -- -- PUMP SKID WITH COUPLING GUARD 1 MILD STEEL

100 50 GPM F02361 F02358 1 --

150 50 GPM F02361 F02360

200 50 GPM F02363 F02360

250 50 GPM F02363 F02364

11 -- -- -- -- PANEL SUPPORT FRAME 1 MILD STEEL

12 -- -- -- -- SUCTION "Y" STRAINER 1 BRONZE

13 -- -- -- -- NAMEPLATE 1 BRONZE


15 -- -- -- -- 1-1/2" 3000# PIPE COUPLING 1 BRONZE

16 -- -- -- -- 1-1/2" PIPE TEE 7 BRONZE

17 -- -- -- -- 1-1/2" 90° PIPE ELBOW 4 BRONZE

18 -- -- -- -- 1-1/2" BALL VALVE 3 STAINLESS STEEL

19 -- -- -- -- 1-1/2" MISC. NIPPLES AND PIPE 1 LOT BRONZE

-Indicates replacement part not available

MOTOR, 20 HP, 1800 RPM


FOAMPAK 13S


2

F02342 F02342



TECHNICAL DATA

Foam 250j February 26, 2003

OBSOLETE





75, 100 and 150 GPM

February 26, 2003 Foam 250k

OBSOLETE

ITEMDISCHARGE

PRESSURE PSICONCENTRATE

FLOWPART NO.

50 HZPART NO.

60 HZ.DESCRIPTION QTY MATERIAL

100 75 GPM F02311 F02310 1 BRONZE

150 75 GPM F02311 F02310

200 75 GPM F02311 F02310

250 75 GPM F02328 F02328

100 100 GPM F02312 F02310

150 100 GPM F2312 F02310

200 100 GPM F02312 F02310

250 100 GPM F02328 F02328

100 150 GPM F02319 F02313

150 150 GPM F02319 F02313

200 150 GPM F02319 F02314

250 150 GPM F02333 F02329

100 75 GPM F02380 F02379 1 --

150 75 GPM F02380 F02381

200 75 GPM F02382 F02383

250 75 GPM F02384 F02387

100 100 GPM 2380 F02379

150 100 GPM F02382 F02381

200 100 GPM F02384 F02383

250 100 GPM F02384 F02387

100 150 GPM F02382 F02383

150 150 GPM F02386 F02385

200 150 GPM F02388 F02387

250 150 GPM F02388 F02387

3 -- -- -- -- 2" PRESSURE RELIEF VALVE 1 BRONZE

4 -- -- -- -- 2" CLAVAL VALVE 1 BRONZE



7 -- -- -- --

8 -- -- -- -- 2" 150# SCREWED FLANGE 5 BRONZE


100 75 GPM F02363 F02362 1 --

150 75 GPM F02363 F02364

200 75 GPM F02365 F02366

250 75 GPM F02367 F02353

100 100 GPM F02363 F02362

150 100 GPM F02365 F02364

200 100 GPM F02367 F02353

250 100 GPM F02367 F02353

100 150 GPM F02365 F02366

150 150 GPM F02369 F02368

200 150 GPM F02346 F02345

250 150 GPM F02346 F02345


12 -- -- -- -- SUCTION "Y" STRAINER 1 BRONZE


14 -- -- -- -- 2" CLASS 150 PIPE UNION 2 BRONZE

15 -- -- -- -- 2" 3000# PIPE COUPLING 1 BRONZE

16 -- -- -- -- 2" PIPE TEE 7 BRONZE

17 -- -- -- -- 2" 90° PIPE ELBOW 4 BRONZE

EMI FTA-750 CONTROL PANEL

MOTOR, 40 HP, 1800 RPM2

FOAMPAK 26S


10

F02342 F02342




Foam 250 l February 26, 2003

OBSOLETE





200, 250 and 300 GPM

February 26, 2003 Foam 250 m

OBSOLETE


PSI

CONCENTRATEFLOW

PART NO.50 HZ.

PART NO.60 HZ.


100 200 GPM F02319 F02319 1 BRONZE

150 200 GPM F02319 F02319

200 200 GPM F02319 F02319

250 200 GPM F02334 F02333

100 250 GPM F02321 F02320

150 250 GPM F02321 F02320

200 250 GPM F02321 F052320

250 250 GPM F02336 F02335

100 300 GPM 0F2321 F02321

150 300 GPM F02321 F02321

200 300 GPM F02321 F02321

250 300 GPM F02336 F02336

100 200 GPM F02384 F02385 1 --

150 200 GPM F02388 F02387

200 200 GPM F02388 F02389

250 200 GPM F02390 F02391

100 250 GPM F02388 F02387

150 250 GPM F02390 F02389

200 250 GPM F02390 F02389

250 250 GPM F02392 F02393

100 300 GPM F02388 F02389

150 300 GPM F02390 F02391

200 300 GPM F02392 F02393

250 300 GPM F02394 F02393

3 -- -- -- -- 2-1/2" PRESSURE RELIEF VALVE 1 BRONZE




7 -- -- -- --

8 -- -- -- -- 3" 150# SCREWED FLANGE 5 BRONZE


100 200 GPM F02367 F02368 1 --

150 200 GPM F02346 F02345

200 200 GPM F02346 F02347

250 200 GPM F02348 F02349

100 250 GPM F02346 F02345

150 250 GPM F02348 F02347

200 250 GPM F02348 F02347

250 250 GPM F02350 F02351

100 300 GPM F02346 F02347

150 300 GPM F02348 F02349

200 300 GPM F02350 F02351

250 300 GPM F02352 F02349

11 -- -- -- -- PANEL SUPPORT FRAME 1 BRONZE

12 -- -- -- -- 3" SUCTION "Y" STRAINER 1 BRONZE



15 -- -- -- -- 3" X 2-1/2" 3000# REDUCING COUPLING 2 BRONZE

16 -- -- -- -- 3" PIPE TEE 6 BRONZE


FOAMPAK 50S

EDWARDS MODEL 300-368 PUMP1

2 MOTOR, 60 HP, 1800 RPM


F02342 F02342




February 26, 2003Foam 250n

OBSOLETE




FOAMPAK 59SConcentrate Flow350 and 400 GPM

February 26, 2003 Foam 250 o

OBSOLETE


PSI

CONCENTRATEFLOW

PART NO.50 HZ.

PART NO.60 HZ.


100 350 GPM F02323 F02322

150 350 GPM F02323 F02323

200 350 GPM F02338 F02337

250 350 GPM F02338 F02337

100 400 GPM F02324 F02323

150 400 GPM F02324 F02323

200 400 GPM F02339 F02338

250 400 GPM N/A F02338

100 350 GPM F02392 F02391

150 350 GPM F02392 F02393

200 350 GPM F02394 F02395

250 350 GPM F02396 F02395

100 400 GPM F02396 F02393

150 400 GPM F02396 F02395

200 400 GPM F02396 F02395

250 400 GPM N/A F02395

3 -- -- -- -- 3" PRESSURE RELIEF VALVE 1 BRONZE

4 -- -- -- -- 3" CLAVAL VALVE 1 BRONZE



7 -- -- -- --

8 -- -- -- -- 4" _____# SCREWED FLANGE 7 BRONZE


100 350 GPM F02350 F02349

150 350 GPM F02350 F02349

200 350 GPM F02352 F02343

250 350 GPM F02344 F02343

100 400 GPM F02344 F02351

150 400 GPM F02344 F02343

200 400 GPM F02344 F02343

250 400 GPM N/A F02343


12 -- -- -- -- 4" SUCTION "Y" STRAINER 1 BRONZE


14 -- -- -- -- 3" CLASS 150 PIPE UNION 2 BRONZE

15 -- -- -- -- 4" X3" 3000# REDUCING COUPLING 2 BRONZE

16 -- -- -- -- 4" PIPE TEE 6 BRONZE


18 -- -- -- -- 4" BALL VALVE 2 STAINLESS STEEL

19 -- -- -- -- 4" MISC. NIPPLES AND PIPE 1 LOT BRONZE

20 -- -- -- -- 3" BALL VALVE 1 STAINLESS STEEL


22 -- -- -- -- 3" PIPE TEE 1 BRONZE

23 -- -- -- -- 4" X3" REDUCING BUSHING 1 BRONZE

24 -- -- -- -- 3" MISC. NIPPLES AND PIPE 1 LOT BRONZE

-Indicates replacement part not available

FOAMPAK 59S

1

2

EDWARDS MODEL 400-4112 PUMP

MOTOR, 75 HP, 1800 RPM

1 BRONZE

1

1 --10 EMI FTA-1000 CONTROL PANEL

--

F02343 F02343




February 26, 2003Foam 250 p

Form No. F_050399 Replaces page 250a-o January 7, 2002. (Revised Pump SelectionChart to reflect 60 Hz and 50 Hz and updated area code.)

OBSOLETE

foampak technical data - viking group inc · the most remote riser by 20 to 30 psi (1.5 to 2 bar)....

Documents