gu03[1]
TRANSCRIPT
住宅式氣體熱水爐裝置規定INSTALLATION REQUIREMENTS FORDOMESTIC GAS WATER HEATERS
( 熱 負 荷 在 7 0 千 瓦 以 內 者 )
( RATED HEAT INPUT UP TO 70 kW )
工作守則:氣體應用指南之三CODE OF PRACTICE GU 03
氣體安全監督 Gas Authority
香港特別行政區政府
住宅式氣體熱水爐裝置規定(熱負荷在 70 千瓦以內者)
工作守則:氣體應用指南之三
二零零一年十月
第二版
目 錄
1. 前 言 第 1 頁
2. 範 圍 和 詞 彙 第 3 頁
3. 氣 體 熱 水 爐 的 挑 選 及 安 裝 位 置 第 6 頁
4. 通 風 第 10 頁
5. 氣 體 供 應 第 12 頁
6. 電 氣 規 定 第 13 頁
7. 給 水 、 排 水 及 釋 壓 第 14 頁
8. 投 入 運 作 第 15 頁
9. 標 貼 及 客 戶 須 知 事 項 第 16 頁
附 錄 A 住 宅 式 氣 體 熱 水 爐 裝 置 標 準 第 17 頁
附 錄 B 密 封 式 熱 水 爐 煙 道 末 端 可 接 受 的 安 裝 位 置 第 18 頁
附 錄 C 戶 外 式 氣 體 熱 水 爐 最 低 分 隔 距 離 及 額 外 限 制 第 20 頁
附 錄 D 有 關 戶 外 式 氣 體 熱 水 爐 的 警 告 告 示 及 警 告 信 息 第 23 頁
附 錄 E 戶 外 式 氣 體 熱 水 爐 進 口 商 的 紀 錄 管 理 第 24 頁
附 錄 F 密 封 式 (自 然 排 煙 型 )及 普 通 煙 道 式 機 動 排 煙 型 第 25 頁
氣 體 熱 水 爐 的 供 應 空 氣 開 口
附 錄 G 有 關 空 氣 的 規 定 - 往 宅 式 氣 體 熱 水 爐 的 機 動 排 煙 安 排 第 26 頁
1
1. 前 言
1.1 本 工 作 守 則 旨 在 就 香 港 住 宅 式 氣 體 熱 水 爐 的 安 裝 要 求 , 為
氣 體 爐 具 入 口 商 及 供 應 商 、 註 冊 氣 體 工 程 承 辦 商 及 註 冊 氣
體 裝 置 技 工 提 供 指 引 。 本 工 作 守 則 (下 稱 守 則 )是 由 氣 體 安
全 監 督 根 據 《 氣 體 安 全 條 例 》 (第 51 章 )第 9 條 的 規 定 批 准
及 出 版 的 。
1.2 本 守 則 所 載 的 指 引 不 應 被 視 作 鉅 細 無 遺 。 本 守 則 無 意 解 除
安 全 法 例 規 定 有 關 人 士 須 負 上 的 法 定 責 任 。
1.3 本 守 則 具 有 特 別 的 法 律 地 位 。 儘 管 未 有 遵 從 守 則 內 任 何 建
議 並 不 算 違 法 , 但 在 進 行 刑 事 訴 訟 時 , 法 庭 會 將 之 視 為 相
關 因 素 , 以 決 定 有 關 人 士 有 否 違 反 任 何 與 建 議 有 關 的 條
文 。
1.4 本 港 所 有 氣 體 裝 置 工 程 , 均 須 按 照 《 氣 體 安 全 條 例 》 的 規
定 進 行 , 特 別 是 :
(a) 《 氣 體 安 全 (氣 體 供 應 )規 例 》 (第 51 章 );
(b) 《 氣 體 安 全 (裝 置 及 使 用 )規 例 》 (第 51 章 );
(c) 《 氣 體 安 全 (雜 項 )規 例 》 (第 51 章 );
(d) 《 氣 體 安 全 (氣 體 裝 置 技 工 及 氣 體 工 程 承 辦 商 註 冊 )規 例 》 (第 51 章 )及
(e) 《 氣 體 安 全 (氣 體 供 應 公 司 註 冊 )規 例 》 (第 51 章 )。
1.5 另 外 , 下 述 規 例 在 適 當 情 況 下 亦 適 用 :
(a) 《 建 築 物 (設 計 )規 例 》 (第 123F 章 )第 35A 條 ;
(b) 《 水 務 設 施 規 例 》 (第 102 章 )及
(c) 《 電 力 (線 路 )規 例 》 (第 406 章 )。
1.6 裝 置 熱 水 爐 時 除 遵 守 本 守 則 的 規 定 外 , 亦 須 遵 從 製 造 商 的
指 引 。 除 非 製 造 商 的 指 引 與 法 例 規 定 不 符 , 否 則 不 應 以 本
守 則 的 規 定 取 代 製 造 商 的 指 引 。 此 外 , 亦 須 留 意 下 列 最 新
的 規 例 和 工 作 守 則 : -
(a) 《 工 作 守 則 : 氣 體 應 用 指 南 之 五 住 宅 式 氣 體 用 具 的
批 准 》 ;
(b) 《 氣 體 應 用 指 南 之 九 : 用 以 從 容 水 量 少 於 40 升 的
石 油 氣 瓶 供 氣 的 低 壓 調 壓 器 》 ;
(c) 香 港 中 華 煤 氣 有 限 公 司 工 作 守 則 : 住 宅 式 爐 具 裝 置
HKCG/SER/OP7;
(d) 按 《 電 力 (線 路 )規 例 》 (第 406 章 )而 編 訂 的 工 作 守
則 ;
(e) 香 港 電 力 供 應 公 司 的 政 策 要 求 、 供 應 規 則 、 安 裝 指
2
引 和 工 作 守 則 及
(f) 國 際 /國 家 標 準 (請 參 閱 第 1.7 段 )。
1.7 以 下 為 國 際 /國 家 標 準 , 以 供 參 考 :
BS 5440-1 安 裝 及 維 修 熱 負 荷 不 超 過 70 千 瓦 的 氣 體 用
具 的 煙 道 和 通 風 裝 置 ( 第 一 、 第 二 及 第 三 類
別 氣 體 ) - 第 一 部 : 英 國 標 準 協 會 煙 道 安 裝
及 維 修 規 格
BS 5440-2 安 裝 及 維 修 熱 負 荷 不 超 過 70 千 瓦 的 氣 體 用
具 的 煙 道 和 通 風 裝 置 ( 第 一 、 第 二 及 第 三 類
別 氣 體 ) - 第 二 部 : 英 國 標 準 協 會 氣 體 用 具
安 裝 及 維 修 規 格
BS 5546 英 國 標 準 協 會 安 裝 熱 水 供 應 器 作 家 庭 用 途 的
規 格 (使 用 熱 負 荷 不 超 過 70 千 瓦 的 燃 氣 用 具 )
AG 601 澳 洲 氣 體 協 會 氣 體 裝 置
1.8 本 守 則 由 氣 體 安 全 監 督 擬 備 , 並 徵 詢 香 港 的 註 冊 氣 體 供 應
公 司 、 註 冊 氣 體 工 程 承 辦 商 及 住 宅 式 氣 體 用 具 的 入 口 商 和
供 應 商 。
3
2. 範 圍 和 詞 彙
2.1 本 守 則 包 括 設 計 或 擬 於 住 宅 房 產 內 使 用 的 即 熱 式 氣 體 熱 水
爐 及 儲 水 式 氣 體 熱 水 爐 的 新 裝 置 工 程 , 不 管 這 些 爐 具 在 何
處 使 用 , 並 適 用 於 燃 燒 《 氣 體 安 全 條 例 》 (第 51 章 )第 2 條
所 界 定 氣 體 的 氣 體 熱 水 爐 。
2.2 熱 負 荷 達 70 千 瓦 的 氣 體 熱 水 爐 , 必 須 為 氣 體 安 全 監 督 按
照《 工 作 守 則:氣 體 應 用 指 南 之 五 》所 批 准 的 類 別 及 型 號 ,
才 可 進 行 安 裝 (視 乎 批 准 住 宅 式 氣 體 用 具 的 新 法 例 制 訂 情
況 而 定 )。
2.3 詞 彙
2.3.1 氣 體 熱 水 爐 類 別 的 定 義 :
“ 對 衡 式” 一 種 密 封 式 氣 體 熱 水 爐 , 裝 設 有 空 氣 /廢 氣 的 煙 道 進 出 口 , 而 其 設 計 是 使 煙
道 進 出 口 露 出 外 牆 。
“ 機 動 排 煙 式 ” 一 種 設 有 煙 道 系 統 的 氣 體 熱 水 爐 , 而
系 統 是 利 用 風 扇 排 煙 。
“ 無 煙 道 式 ” 一 種 氣 體 熱 水 爐 , 其 設 計 不 會 接 駁 將
燃 燒 廢 氣 由 建 築 物 外 牆 以 內 地 方 排 出
外 面 的 煙 道 。
“ 即 熱 式” 在 這 種 氣 體 熱 水 爐 內 , 水 流 到 出 水 口
時 才 受 熱 。
“ 自 然 排 煙 式 ” 一 種 設 有 煙 道 系 統 的 氣 體 熱 水 爐 , 在
系 統 內 由 燃 燒 廢 氣 的 熱 力 產 生 排 煙 作
用 。
“ 普 通 煙 道 式 ” 這 種 氣 體 熱 水 爐 的 設 計 是 須 接 駁 煙 道
系 統 , 其 燃 燒 空 氣 是 由 爐 具 所 在 房 間
或 戶 內 空 間 抽 取 。
4
“ 戶 外 式” 一 種 設 計 或 擬 為 住 宅 供 應 熱 水 的 氣 體
熱 水 爐 , 而 且 只 可 於 本 守 則 定 明 的 指
定 戶 外 環 境 安 裝 。 若 有 關 裝 置 並 未 與
煙 道 連 接 , 則 必 須 安 裝 在 建 築 物 外 牆 /周 邊 外 的 通 風 恒 常 良 好 的 空 曠 地 方 ,
有 關 地 方 須 在 負 責 人 管 轄 的 指 定 物 業
界 線 以 內 ( 見 屋 宇 署 所 批 准 的 建 築 圖
則 ), 且 有 關 範 圍 嚴 禁 有 人 居 住 。
“ 密 封 式” 這 種 氣 體 熱 水 爐 在 運 作 時 , 其 燃 燒 空
氣 進 口 及 燃 燒 廢 氣 出 口 與 該 爐 具 所 在
房 間 隔 離 。
“ 貯 水 式” 在 這 種 氣 體 熱 水 爐 內 , 貯 存 的 水 在 恒
溫 控 制 下 受 熱 , 供 需 要 時 使 用 。
2.3.2 其 他 定 義 :
“ 住 宅 式 氣 體 用 具 ” 根 據 《 氣 體 安 全 條 例 》 (第 51 章 )的 定
義 , 指 設 計 或 擬 主 要 用 於 住 宅 樓 宇 的
氣 體 用 具 (在 本 守 則 中 解 釋 為 氣 體 熱 水
爐 ), 不 管 這 些 氣 體 用 具 是 否 真 的 作 此
用 途 。
“ 熄 火 保 險 裝 置 ” 一 個 對 火 燄 特 性 敏 感 的 內 置 式 控 制 裝
置 , 如 果 點 火 時 出 現 問 題 或 火 焰 無 意
間 熄 滅 , 該 控 制 裝 置 可 以 感 應 到 沒 有
火 焰 , 而 將 供 應 至 用 具 燃 燒 器 的 氣 體
切 斷 , 以 確 保 安 全 。
“ 氣 體 安 全 監 督 ” 根 據 《 氣 體 安 全 條 例 》 (第 51 章 )第 5條 委 任 的 監 督 。
“ 入 口 商” 從 事 把 住 宅 式 氣 體 熱 水 爐 輸 入 香 港 業
務 的 香 港 公 司 (參 照 《 氣 體 安 全 條 例 》
(第 51 章 )第 2 條 的 定 義 )。
“ 過 熱 保 護 裝 置 ” 一 個 在 正 常 的 溫 度 控 制 方 法 失 效 時 ,
為 保 護 氣 體 熱 水 爐 及 其 附 近 地 方 而 設
的 不 可 調 校 溫 度 感 應 裝 置 。
“ 註 冊 氣 體 工 程 承 辦
商”指 從 事 氣 體 裝 置 工 程 業 務,並 根 據《 氣
體 安 全 條 例 》 (第 51 章 )的 規 定 註 冊 的
人 士 或 公 司 。
5
“ 註 冊 氣 體 裝 置 技
工”指 親 自 進 行 氣 體 裝 置 工 程,並 根 據《 氣
體 安 全 條 例 》 (第 51 章 )註 冊 的 個 人 。
“ 供 應 商” 為 最 終 使 用 者 供 應 氣 體 熱 水 爐 的 香 港
公 司 (根 據 《 氣 體 安 全 條 例 》 (第 51 章 )第 2 條 的 定 義 )。
6
3. 氣 體 熱 水 爐 的 挑 選 及 安 裝 位 置
3.1 不 同 類 別 的 房 間 內 可 容 許 安 裝 氣 體 熱 水 爐 的 位 置 , 載 列 於
附 錄 A GSO/IG/23-3/00 內 。
3.2 初 次 裝 置 熱 水 爐 時 應 首 選 密 封 式 氣 體 熱 水 爐 。 在 浴 室 或 淋
浴 室 以 外 的 地 方 , 如 環 境 不 許 可 裝 置 密 封 式 氣 體 熱 水 爐 ,
應 使 用 機 動 排 煙 式 熱 水 爐 。
3.3 密 封 式 型 號
(a) 初 次 或 更 換 裝 置 時 應 首 選 密 封 式 氣 體 熱 水 爐 。
(b) 新 建 樓 宇 須 遵 從 《 建 築 物 (設 計 )規 例 》 (第 123F 章 )第 35A 條 的 規 定 , 在 指 定 的 位 置 預 留 牆 孔 , 以 備 安
裝 密 封 對 衡 式 熱 水 爐 。 故 此 , 根 據 《 氣 體 安 全 ( 裝
置 及 使 用 )規 例 》第 27 條 的 規 定,如 已 有 適 當 牆 孔 ,
則 只 可 以 安 裝 密 封 式 型 號 , 而 且 必 須 利 用 該 牆 孔 。
(c) 《 建 築 物 (設 計 )規 例 》(第 123F 章 )第 35A 條 的 規 定 ,
主 要 適 用 於 新 建 樓 宇 供 安 裝 密 封 式 爐 具 牆 孔 的 位
置 , 而 附 錄 B 則 列 明 密 封 式 氣 體 熱 水 爐 煙 道 末 端 可
接 受 的 安 裝 位 置 。 不 過 , 在 現 有 房 屋 開 鑿 牆 孔 , 可
能 存 有 困 難 , 而 在 此 情 況 下 使 用 機 動 密 封 式 排 煙 型
熱 水 爐 , 應 屬 可 行 的 辦 法 。
(d) 密 封 式 氣 體 熱 水 爐 可 安 裝 於 大 部 分 的 位 置 , 雖 然 不
宜 安 裝 於 睡 房 或 廳 內 。
(e) 應 特 別 留 意《 建 築 物 (設 計 )規 例 》 (第 123F 章 )第 35A條 及 本 守 則 附 錄 B 有 關 在 光 井 裝 置 爐 具 的 條 文 。 如
樓 宇 的 構 形 可 能 令 到 燃 燒 廢 氣 難 以 排 去 , 則 使 用 機
動 密 封 式 排 煙 型 號 會 較 為 合 宜 。
3.4 普 通 煙 道 式 自 然 排 煙 型 號
根 據 《 氣 體 安 全 (裝 置 及 使 用 )規 例 》 (第 51 章 )第 36 條 的 規
定 , 不 得 安 裝 這 類 即 熱 式 氣 體 熱 水 爐 。
3.5 普 通 煙 道 式 機 動 排 煙 型 號
(a) 這 類 氣 體 熱 水 爐 的 安 裝 位 置 以 通 風 良 好 的 廚 房 、 工
作 間 或 露 台 為 首 選 。 鑑 於 這 類 熱 水 爐 須 抽 取 所 在 空
間 的 空 氣 作 燃 燒 用,故 應 參 照 本 守 則 第 4 段 的 指 示 ,
確 保 任 何 時 候 均 有 足 夠 的 永 久 通 風 孔 。
7
(b) 這 類 氣 體 熱 水 爐 不 得 安 裝 於 睡 房 或 廳 內 。
(c) 不 得 在 浴 室 或 淋 浴 室 初 次 裝 置 這 類 熱 水 爐 。 (初 次 裝
置 時 必 須 使 用 密 封 型 號 , 有 關 規 定 見 本 守 則 第 3.3段 ),根 據《 氣 體 安 全 (裝 置 及 使 用 )規 例 》(第 51 章 ),
第 27(3)條 的 規 定 , 只 有 在 原 已 裝 置 普 通 煙 道 式 機 動
排 煙 型 熱 水 爐 的 情 況 下 , 才 可 獲 准 再 裝 置 同 一 類 爐
具 以 作 替 換 。
3.6 無 煙 道 式 型 號
根 據 《 氣 體 安 全 (裝 置 及 使 用 )規 例 》 第 35 條 的 規 定 , 不 得
安 裝 這 種 氣 體 熱 水 爐 。
3.7 戶 外 型 號
(a) 總 論
氣 體 熱 水 爐 可 安 裝 於 樓 宇 以 外 的 地 方 , 沒 有 接 駁 煙
道 的 指 定 戶 外 型 號 在 安 裝 時 應 嚴 格 遵 守 本 段 詳 列 的
規 定 。
爐 具 入 口 商 只 能 以 「 供 應 -安 裝 -及 -維 修 」 的 形 式 供
應 沒 有 接 駁 煙 道 的 戶 外 型 號 氣 體 熱 水 爐 。
入 口 商 也 應 該 是 供 應 商 , 並 應 確 保 沒 有 接 駁 煙 道 的
戶 外 式 氣 體 熱 水 爐 的 設 計 、 建 造 和 裝 置 符 合 本 守 則
的 條 件 和 規 定 , 包 括 但 不 局 限 於 第 2.2 及 3.7 段 的
規 定 。
(b) 沒 有 接 駁 煙 道 的 戶 外 式 氣 體 熱 水 爐 的 裝 置 規 定 :
(i) 禁 止 安 裝 的 地 點
熱 水 爐 不 得 安 裝 於 牆 上 , 亦 不 得 安 裝 於 下 述 任 何 地
點 :
(1) 在 露 台 內 或 毗 鄰 露 台 ;
(2) 在 空 氣 上 下 流 通 時 有 障 礙 或 在 爐 具 最 低 的 煙
道 末 端 下 並 沒 有 通 往 外 間 的 通 風 管 的 光 井 ;
(3) 在 空 氣 上 下 流 通 時 有 障 礙 的 凹 角 ;
(4) 任 何 結 構 的 底 部 , 例 如 樓 梯 ;
8
(5) 在 地 庫 或 水 平 面 以 下 的 較 低 樓 層 ;
(6) 在 暫 時 或 永 久 的 有 蓋 、 有 遮 擋 或 密 封 的 地 方
如 房 屋 、 箱 /密 室 等 ;
(7) 在 空 氣 不 流 通 的 地 方 ; 或
(8) 在 公 用 設 施 的 空 氣 入 口 或 抽 氣 口 。
(ii) 許 可 情 況
只 可 在 符 合 下 述 兩 種 情 況 下 安 裝 熱 水 爐 :
(1) 在 以 下 所 界 定 的 指 定 通 風 良 好 地 點 , 有 關 地
點 除 了 托 架 外 並 無 任 何 暫 時 或 永 久 的 結 構 或
障 礙 。
在 地 平 線 以 上 地 面 的 無 上 蓋 天 井 ; 或
無 上 蓋 的 天 台 ; 或
無 上 蓋 的 平 台 ; 及
(2) 在 建 築 物 外 牆 / 週 邊 的 牢 固 托 架 上 , 托 架 設
有 安 全 及 穩 妥 的 不 可 燃 基 座 或 結 構 , 托 架 上
方 永 無 遮 擋 , 且 在 熱 水 爐 兩 側 均 有 通 風 良 好
且 不 少 於 500 毫 米 、 前 方 不 少 於 600 毫 米 的
無 障 礙 物 範 圍 。
(c) 熱 水 爐 的 裝 設
熱 水 爐 不 得 裝 設 於 牆 上 , 其 安 裝 的 方 向 應 可 讓 煙 道
末 端 將 廢 氣 由 外 牆 / 週 邊 排 到 地 平 線 以 上 的 地 方 ,
外 牆 / 週 邊 與 熱 水 爐 背 面 應 保 持 暢 通 無 阻 , 根 據 製
造 商 的 指 引 , 熱 水 爐 應 為 裝 設 於 地 面 的 型 號 。
(d) 地 點 的 限 制
根 據 附 錄 C- “ 戶外 式 氣 體 熱 水 爐 最 低 分 隔 距 離 及 額
外 限 制” 的 規 定 , 實 施 最 低 分 隔 距 離 和 額 外 限 制 。
(e) 警 告 告 示 /信 息
在 熱 水 爐 的 當 眼 處 須 貼 上 警 告 標 籤 , 標 籤 最 少 為
130 毫 米 x 130 毫 米 , 以 耐 用 及 防 風 雨 的 物 料 製
造 , 上 面 以 11 號 或 更 大 的 中 英 文 字 型 , 載 列 包
括 但 不 局 限 於 附 錄 D- “ 有 關 戶 外 式 氣 體 熱 水 爐 的
9
警
告 告 示 及 警 告 信 息 ” 的 資 料 。
此 外 , 亦 應 把 載 有 相 同 中 英 文 資 料 的 警 告 告 示 /信息 , 送 交 購 買 或 接 手 擁 有 / 使 用 熱 水 爐 的 發 展 商 /佔 用 人 / 擁 有 人 / 租 戶 / 客 戶 , 並 保 留 簽 收 回 條 , 以
資 記
錄 。
警 告 告 示 及 警 告 信 息 的 式 樣 載 於 附 錄 D。
(f) 裝 置 、 測 試 、 校 驗 、 撿 查 及 維 修
入 口 商 須 負 責 安 排 註 冊 氣 體 工 程 承 辦 商 , 進 行 裝
置 、 測 試 、 校 驗 工 作 , 並 在 其 後 定 期 檢 查 和 維 修 每
部 已 安 裝 的 熱 水 爐 。 檢 查 工 作 至 少 每 年 一 次 , 以 查
證 第 3.7 段 (a)至 (e)條 的 規 定 已 獲 遵 從 。 檢 查 報 告
須 保 存 作 紀 錄 用 途 , 並 應 根 據 符 合 規 定 清 單 的 要
求 , 紀 錄 所 有 檢 查 結 果 , 報 告 應 由 負 責 有 關 工 作 的
註 冊 氣 體 裝 置 技 工 簽 署 。
(g) 紀 錄 管 理
入 口 商 須 在 熱 水 爐 的 使 用 壽 命 期 內 妥 善 保 存 熱 水 爐
的 完 整 紀 錄 , 氣 體 安 全 監 督 在 有 需 要 時 會 查 閱 有 關
紀 錄 。 紀 錄 須 包 括 但 不 限 於 附 錄 E 所 載 列 的 內 容 。
10
4. 通 風
4.1 空 氣 供 應
(a) 根 據 《 氣 體 安 全 (裝 置 及 使 用 )規 例 》 (第 51 章 )第 23條 的 規 定 , 氣 體 熱 水 爐 應 安 裝 於 有 足 夠 永 久 通 風 孔
的 地 點 , 讓 氣 體 完 全 燃 燒 並 把 廢 氣 適 當 地 排 出 , 且
能 在 正 常 的 操 作 情 況 下 將 附 近 的 環 境 溫 度 維 持 在 安
全 範 圍 內 。
(b) 空 氣 供 應 不 應 受 燃 燒 廢 氣 污 染 , 亦 不 應 含 可 以 影 響
燃 燒 的 化 學 品 及 易 燃 氣 化 物 。
(c) 附 錄 A GSO/IG/23-3/00 載 列 各 種 氣 體 式 熱 水 爐 的
最 小 房 間 / 間 隔 室 通 風 孔 要 求 。 若 使 用 自 然 通 風 系
統 , 便 應 按 照 附 錄 A GSO/IG/23-3/00 的 規 定 , 提
供 永 久 的 低 位 及 高 位 開 口 。 這 些 開 口 應 裝 有 低 阻 力
的 柵 格 / 百 葉 , 並 應 設 於 不 會 引 致 堵 塞 或 水 浸 的 地
方 。
(d) 若 密 封 式 氣 體 熱 水 爐 是 安 裝 於 間 隔 室 內 , 則 應 提 供
通 風 孔 作 散 熱 用 途 (見 附 錄 A GSO/IG/23-3/00 的 最
小 間 隔 室 通 風 孔 要 求 )。
(e) 附 錄 F 圖 示 密 封 式 (自 然 排 煙 型 )及 普 通 煙 道 式 機 動
排 煙 型 氣 體 熱 水 爐 的 供 氣 口 。
(f) 至 於 安 裝 於 房 間 的 儲 水 式 熱 火 爐 的 空 氣 供 應 及 通 風
孔 要 求 , 請 參 閱 英 國 標 準 5440 或 同 等 及 製 造 商 的
指 引 。
(g) 無 論 何 時 , 均 應 遵 守 《 氣 體 安 全 ( 裝 置 及 使 用 ) 規
例 》 (第 51 章 )第 23 及 24(4) 條 的 規 定 。 如 認 為
須 使 用 機 械 通 風 裝 置 , 則 所 有 空 氣 入 口 及 抽 風 扇
均 應 裝 有 故 障 保 險 自 動 控 制 器 , 俾 能 在 氣 流 無 法
內 進 及 抽 出 時 關 閉 或 鎖 上 熱 水 爐 。 氣 體 熱 水 爐 的
空 氣 供 應 應 按 照 製 造 商 的 指 引 辦 理 , 如 沒 有 指
引 , 則 應 參 考 附 錄 G 或 同 等 的 國 際 /國 家 標 準 。
4.2 煙 道
(a) 無 論 何 時 , 均 應 遵 守 《 氣 體 安 全 ( 裝 置 及 使 用 ) 規
例 》 ( 第 51 章 ) 第 24 條 的 規 定 , 附 錄 AGSO/IG/23-3/00 載 有 各 種 氣 體 熱 水 爐 煙 道 末 端 位
11
置 的 規 定 。
(b) 關 於 機 動 排 煙 式 氣 體 熱 水 爐 的 煙 道 管 最 大 長 度 、 彎
位 最 大 數 目 等 , 應 參 閱 製 造 商 的 指 引 。
(c) 至 於 儲 水 式 氣 體 熱 水 爐 的 資 料 , 請 參 閱 英 國 標 準
5440 或 同 等 及 製 造 商 的 指 引 。
12
5. 氣 體 供 應
5.1 所 有 氣 體 裝 置 工 程 必 須 按 照 《 氣 體 安 全 ( 裝 置 及 使 用 ) 規
例 》 (第 51 章 )第 I I、 IV及 V部 的 規 定 進 行 。
5.2 必 須 確 保 氣 體 熱 水 爐 能 與 所 接 駁 的 氣 體 類 別 和 供 氣 壓 力 相
配 。 有 關 這 方 面 問 題 , 應 參 考 製 造 商 的 指 引 。
5.3 氣 體 熱 水 爐 應 以 金 屬 喉 管 來 接 駁 氣 體 供 應 , 在 靠 近 爐 具 的
地 方 須 裝 置 一 個 不 會 因 意 外 觸 碰 而 啟 動 的 氣 體 切 斷 閥 。 在
裝 置 爐 具 時 , 應 盡 量 減 少 使 用 配 件 及 接 頭 。
5.4 必 須 遵 從 有 關 的 香 港 註 冊 氣 體 供 應 公 司 所 訂 定 的 安 裝 、 檢
漏 及 驅 氣 程 序 。
5.5 必 須 為 儲 水 式 熱 水 爐 提 供 裝 置 , 以 確 保 在 恒 溫 器 失 靈 時 ,
貯 水 容 器 內 不 會 出 現 壓 力 過 高 的 情 況 (見 第 7.4 段 ), 這 或
包 括 一 個 由 溫 度 或 壓 力 啟 動 的 安 全 裝 置 , 俾 能 在 這 種 情 況
下 截 斷 氣 體 供 應 。
13
6. 電 氣 規 定
6.1 電 力 供 應 與 其 保 護 設 備 應 符 合 本 港 電 力 公 司 的 供 電 則 例 、
由 機 電 工 程 署 出 版 的 《 電 力 (線 路 )規 例 》 (第 406 章 )工 作
守 則 ; 或 英 國 電 機 工 程 師 學 會 最 新 版 本 的 《 佈 線 規 例 》 的
最 新 規 定 。
6.2 在 浴 室 或 淋 浴 室 內 裝 置 機 動 排 煙 式 氣 體 熱 水 爐 , 應 特 別 注
意 下 列 事 項 -
(a) 熱 水 爐 的 外 置 開 關 掣 及 爐 外 變 壓 器 部 件 , 須 裝 置 在
浴 室 或 淋 浴 室 外 面 。
(b) 浴 室 或 淋 浴 室 內 不 得 裝 置 插 座 。
(c) 保 護 器 件 的 性 能 以 及 接 地 安 排,須 符 合 本 守 則 第 6.1段 所 提 有 關 規 例 及 工 作 守 則 的 規 定 , 特 別 是 防 止 因
間 接 碰 觸 帶 電 導 體 而 致 觸 電 的 保 護 措 施 。 安 裝 安 全
器 件 如 電 流 式 漏 電 斷 路 器 , 可 確 保 在 發 生 間 接 碰 觸
的 情 況 下 , 能 於 0.4 秒 內 截 斷 電 源 。
14
7. 給 水 、 排 水 及 釋 壓
7.1 氣 體 熱 水 爐 應 符 合 本 港 《 水 務 設 施 規 例 》 (第 102 章 )有 關
條 文 的 規 定 。
7.2 氣 體 熱 水 爐 應 適 宜 在 本 港 一 般 食 水 管 靜 水 壓 之 下 使 用 , 及
/或 應 能 與 水 務 監 督 指 定 接 駁 的 供 水 壓 力 配 合 。
7.3 熱 水 喉 管 最 好 能 適 當 隔 熱 , 以 保 存 熱 能 (如 適 用 )。
7.4 無 排 氣 喉 的 儲 水 式 熱 水 爐 應 設 有 裝 置 , 以 防 止 恒 溫 器 失 靈
時 出 現 壓 力 過 高 的 情 況 , 這 包 括 壓 力 感 應 釋 壓 閥 及 高 溫 斷
流 裝 置 或 溫 度 感 應 釋 壓 閥 。 釋 壓 閥 的 閥 口 不 應 有 所 封 閉 。
15
8. 投 入 運 作
8.1 在 安 裝 氣 體 熱 水 爐 後 , 須 按 照 《 氣 體 安 全 (裝 置 及 使 用 )規
例 》 (第 51 章 )第 30 條 的 規 定 , 將 氣 體 熱 水 爐 投 入 運 作 。
8.2 首 先 必 須 檢 查 已 完 成 的 裝 置 工 程 , 確 保 氣 體 熱 水 爐 是 遵 照
製 造 商 的 指 引 及 本 守 則 安 裝 。
8.3 隨 後 應 對 氣 體 喉 管 及 氣 體 熱 水 爐 進 行 加 壓 檢 漏 試 驗 。
8.4 裝 置 通 過 加 壓 檢 漏 試 驗 後 , 便 須 依 照 製 造 商 的 指 引 進 行 驅
氣 程 序 。
8.5 整 個 給 水 系 統 應 予 徹 底 沖 洗 , 確 保 已 依 照 製 造 商 的 特 別 指
引 進 行 。
8.6 氣 體 熱 水 爐 應 按 照 製 造 商 指 引 所 載 的 次 序 點 火 。
8.7 應 檢 查 氣 體 熱 水 爐 的 所 有 控 制 裝 置 , 包 括 以 人 手 操 作 的 面
板 旋 鈕 及 自 動 操 作 的 恆 溫 器 、 熄 火 保 險 裝 置 等 , 確 保 運 作
正 常 。 有 關 詳 情 , 應 參 考 製 造 商 的 指 引 。
8.8 至 於 機 動 排 煙 式 氣 體 熱 水 爐 , 應 檢 查 風 扇 故 障 保 險 裝 置 ,
確 保 符 合 製 造 商 所 訂 規 格 。
16
9. 標 貼 及 客 戶 須 知
9.1 標 貼
註 冊 氣 體 裝 置 技 工 應 確 保 內 容 包 括 用 戶 操 作 程 序、安 全 信 息 、
警 告 告 示 等 由 製 造 商 提 供 或 規 定 的 中 英 文 標 貼 , 已 經 貼 在 氣
體 熱 水 爐 上 的 當 眼 位 置 。 戶 外 式 氣 體 熱 水 爐 則 應 貼 上 特 別 標
貼 , 有 關 規 定 概 述 於 本 守 則 第 3.7(e)條 。
9.2 客 戶 須 知
(a) 根 據 《 氣 體 安 全 (裝 置 及 使 用 )規 例 》 (第 51 章 )第 26 條 的 規
定 , 應 給 予 客 戶 一 本 由 製 造 商 供 應 的 中 英 文 用 戶 指 引 。
(b) 應 在 氣 體 熱 水 爐 使 用 前 , 向 客 戶 示 範 操 作 氣 體 熱 水 爐 及 其
控 制 器 件 的 正 確 程 序 , 亦 應 把 必 要 的 防 護 措 施 告 知 顧 客 ,
以 確 保 氣 體 熱 水 爐 安 全 操 作 。
(c) 應 告 知 客 戶 , 為 使 氣 體 熱 水 爐 保 持 有 效 及 安 全 操 作 , 必 須
遵 照 製 造 商 的 指 引 及 有 關 工 作 守 則 的 規 定 , 定 期 (至 少 每 年
一 次 )為 氣 體 熱 水 爐 進 行 檢 修 。
(d) 對 於 裝 有 戶 外 式 氣 體 熱 水 爐 的 顧 客 , 應 給 予 本 守 則 第 3.7(e)
條 所 概 述 的 特 別 建 議 。
17
附 錄 A
(GSO/IG/23-3/00)住 宅 式 氣 體 熱 水 爐 裝 置 標 準
- 裝 置 熱 水 爐 時 除 遵 守 本 守 則 的 規 定 外 , 亦 須 遵 從 製 造 商 的 指 引 。 除 非 製 造 商 的 指 引 與 法 例
規 定 不 符 , 否 則 不 應 以 本 守 則 的 規 定 取 代 製 造 商 的 指 引 。
- 初 次 裝 置 熱 水 爐 時 應 首 選 密 封 式 氣 體 熱 水 爐 。 在 浴 室 或 淋 浴 室 以 外 的 地 方 , 如 環 境 不 許 可
裝 置 密 封 式 氣 體 熱 水 爐 , 應 使 用 機 動 排 煙 式 熱 水 爐 。
有 關 每 類 氣 體 熱 水 爐 的 規 定房 間 類 別 及 裝 置
密 封 式 普 通 煙 道 式 機 動 排 煙 式
初 次 裝 置 不 可 裝 置浴 室 或 淋 浴 室
更 換 裝 置
可 以 裝 置
可 以 裝 置
惟 該 熱 水 爐 須 於 1994 年 1 月
1 日 前 裝 置 , 並 以 另 一 個 普
通 煙 道 式 機 動 排 煙 型 熱 水 爐
予 以 更 換
初 次 裝 置廚 房 或 工 作 間
更 換 裝 置可 以 裝 置 可 以 裝 置
初 次 裝 置露 台
更 換 裝 置可 以 裝 置 可 以 裝 置
初 次 裝 置睡 房 或 廳
更 換 裝 置不 太 適 宜 不 可 裝 置
房 間 內 需 有 的 最 小 通 風 孔 (註 1)
每 千 瓦 流 動 空 氣 通 風
口 面 積 (註 2) 7 千 瓦 - 每 分 鐘 5 公 升
12 千 瓦 -每 分 鐘 7 公 升
16 千 瓦 -每 分 鐘 9 公 升
20 千 瓦 -每 分 鐘 11 公 升
24 千 瓦 -每 分 鐘 13 公 升
28 千 瓦 - (熱 水 量 ) 70 千 瓦
無 需 要
額 定 熱 負 荷 超 過 7 千 瓦 但 不
超 過 70 千 瓦 的 熱 水 爐 為 每 千
瓦 5 平 方 厘 米
高 位 每 千 瓦 10 平 方 厘 米 * 每 千 瓦 10 平 方 厘 米向 室 內
低 位 每 千 瓦 10 平 方 厘 米 * 每 千 瓦 20 平 方 厘 米
高 位 每 千 瓦 5 平 方 厘 米 * 每 千 瓦 5 平 方 厘 米
間 隔 室 內 需 有 的 最
小 通 風 孔
( 每 千 瓦 流 動 空 氣
通 風 口 面 積 ) (註 3)
向 室 外低 位 每 千 瓦 5 平 方 厘 米 * 每 千 瓦 10 平 方 厘 米
煙 道 末 端 自 然 排 煙 式須 符 合 《 建 築 物 ( 設 計 ) 規
例 》 第 35A 條 的 規 定
機 動 排 煙 式在 建 築 物 任 何 開 口 至 少
300 毫 米 之 下
在 建 築 物 任 何 開 口 至 少 300毫 米 之 下
*有 關 規 定 只 適 用 於 自 然 排 煙 型 氣 體 熱 水 爐 。 至 於 機 動 排 煙 式 氣 體 熱 水 爐 , 須 參 照 製 造 商 的 指
引 。
註 1- 房 間 內 的 通 風 孔 是 指 與 室 外 空 氣 直 接 相 通 的 通 風 孔 。
註 2- 永 久 開 口 須 為 沒 有 障 礙 物 的 通 風 口 。
註 3- 間 隔 室 內 的 通 風 孔 指 並 非 與 室 外 空 氣 直 接 相 通 的 通 風 孔 。
18
附 錄 B
密 封 式 熱 水 爐 煙 道 末 端 可 接 受 的 安 裝 位 置
外 觀 圖
尺 寸 最 小 距 離
A 距離任何建築物轉角 300 毫 米 *
B 距離任何毗鄰的建築
物開口
300 毫米
C 距離對面的牆壁或周
邊
1500 毫米*
D 凹角的最小平面闊度 1500 毫米*
E 在露台或同類結構物
之下
300 毫米*
F
及
G
光井平面面積(F × G)
10 樓或以下
11-19 樓
20 樓或以上
3000 毫米
4000 毫米
5000 毫米
*如 屬 機 動 排 煙 型 號 , 此 數 字 可 以 較 小 。
參 考 製 造 商 的 指 引 。
光 井
空 氣 上 下 流 通 時 並 無 障 礙 。
在 最 低 的 煙 道 末 端 下 有 通 住 外 間 的 通 風 口 。 每 一 面 向 光 井 的 煙 道
末 端 , 其 通 風 口 最 小 面 積 須 為 0.05 平 方 米 。 通 風 口 內 部 尺 寸 最 小
為 200 毫 米 。
如 冷 氣 機 從 光 井 抽 取 空 氣 , 須 設 有 額 外 的 通 風 口 。
參 考 有 關 平 面 尺 寸 (F × G)的 限 制 。
凹 角
不 得 妨 礙 空 氣 上 下 流 通 。
在 任 何 一 層 , 橫 樑 所 佔 的 面 積 , 不 得 使 凹 角 的 露 天 面 積 減 少 超 過
20%[即 Y ≦ 20% (X + Y)]。
參 考 最 小 平 面 闊 度 (D)的 限 制 。
19
內 觀 圖
尺 寸 最 小
K
N
Q
無 障 礙 物 的
地 方
100 毫 米
150 毫 米
50 毫 米
P 離 地 板 高 度 200 毫 米
(2400 毫 米 最 大 )
L×
M
標 準 尺 寸
非 標 準 尺 寸
380×380 毫 米
或
240×240 毫 米
按 情 況 適 合
陰 影 部 分 代 表 沒 有 障 礙 物 的 範 圍
20
附 錄 C戶 外 式 氣 體 熱 水 爐 的 最 低 分 隔 距 離 及 額 外 限 制
- 裝 置 熱 水 爐 時 除 遵 守 本 守 則 的 規 定 外 , 亦 須 遵 從 製 造 商 的 指 引 。 除
非 製 造 商 的 指 引 與 法 例 規 定 不 符 , 否 則 不 應 以 本 守 則 的 規 定 取 代 製
造 商 的 指 引 。
有 關 戶 外 式 氣 體 熱 水 爐 的 最 低 分 隔 距 離 摘 要 載 於 表 1 及 表 2, 而 熱 水
爐 的 周 圍 簡 圖 則 載 於 圖 1 及 圖 2。 分 隔 距 離 是 指 戶 外 式 氣 體 熱 水 爐 (下
稱 熱 水 爐 )邊 緣 與 其 他 開 口 /物 體 的 最 近 邊 緣 /轉 角 之 間 的 最 短 距 離 。
(a) 表 1 顯 示 與 毗 鄰 開 口 例 如 窗 口 、 門 口 等 的 分 隔 距 離 。
最 低 分 隔 距 離 (毫 米 )
尺 寸 說 明 自 然 排 煙
類 別
機 動 排 煙
類 別
不 超 過 150 500 300>150 至 200 1,500 500P
由 側 牆 上 開 口
起 計 的 點 到 點
距 離
額 定 值
(兆 焦 耳 /小 時 ) >200 1,500 1,500
---沿 機 動 排 煙 式 熱 水 爐 排 氣 方 向 的 水
平 距 離--- 1,500
不 超 過 150 500 300Q
由 熱 水 爐 後 牆
上 開 口 起 計 的
水 平 距 離
額 定 值
(兆 焦 耳 /小 時 ) >150 1,500 300
不 超 過 150 1,000 300
R由 熱 水 爐 後 牆
上 開 口 起 計 的
垂 直 距 離
額 定 值
(兆 焦 耳 /小 時 ) >150 1,500 300
單 位 換 算 : 1 兆 焦 耳 /小 時 = 0.28 千 瓦
(b) 表 2 顯 示 與 貼 近 物 件 的 分 隔 距 離 。
尺 寸 說 明 最 低 分 隔 距 離 (毫 米 )
S 距 離 牆 壁 的 內 外 轉 角 500
T 距 離 另 一 個 熱 水 爐 或 氣 體 用 具 (邊 ) 500
X 距 離 對 面 的 牆 壁 或 周 邊 1,500
Y 距 離 對 面 障 礙 物 600
Z 在 屋 簷 或 同 類 結 構 物 之 下 500
--- 距 離 氣 體 錶 、 電 錶 或 可 能 產 生 火 花 的
裝 置
1,000 且 不 得
位 於 正 下 方
--- 由 地 面 至 煙 道 口 500
--- 與 喉 管 距 離 150
--- 與 易 燃 物 體 距 離 500
21
熱 水 爐 的 前 方 、 頂 部 和 兩 側 在 任 何 時 間 均 須 沒 有 障 礙 物 。 如 安 裝 在 屋
簷 或 同 類 結 構 物 下 , 屋 簷 或 同 類 結 構 物 下 的 突 出 範 圍 不 應 完 全 覆 蓋 熱
水 爐 。 熱 水 爐 的 煙 道 口 不 應 直 接 指 向 其 他 公 用 設 施 或 用 具 (如 分 體 式 空
調 機 )的 入 口 、 出 口 或 管 道 。
(c) 圖 1 的 平 面 圖 顯 示 熱 水 爐 的 無 障 礙 物 範 圍 為 熱 水 爐 兩 側 不 少 於 500
毫 米 和 前 方 不 少 於 600 毫 米 。
戶 外 式 氣 體 熱 水 爐
500 毫 米 500 毫 米
600 毫 米
排 氣 方 向 (離 開 建 築 物 牆 /週 邊 , 面 向 外 面
露 天 範 圍 )
無 障 礙 物 範 圍
(d) 圖 2 顯 示 表 1 及 表 2 所 示 的 最 低 分 隔 距 離 。
22
23
附 錄 D
有 關 戶 外 式 氣 體 熱 水 爐 的 警 告 告 示 及 警 告 信 息
以 下 為 張 貼 於 無 煙 道 戶 外 式 氣 體 熱 水 爐 的 警 告 告 示 範 例 :
安 全 告 示 / 指 示 S A F E T Y N O T I C E / M E S S A G E警 告
1. 本熱水器是戶外式燃氣熱水器。 衹准於屋宇以外的、露天的特定地方安裝。 必
須確保周圍空氣流通。阻礙通風,會有性命危險。
2. 在本熱水器所在處之左方、右方或頂方距離不少於 0.5 米內及前方不少於 0.6 米範
圍內,不得有任何障礙物或建築物之部份存在。
3. 須由政府註冊氣體工程承辦商聘用之註冊氣體裝置技師進行安裝及作定期安全檢
查及維修。每年至少一次。
4. 如有任何查詢/緊急事故,請致電
xxx 公 司
電話 xxxx xxxx xxxx xxxx 傳真 xxxx xxxx
C A U T I O N
1. This is an OUTDOOR type gas water heater. It must ONLY be installed in aprescribed outdoor open space and must be well-ventilated. It is hazardous to life ifventilation is impaired.
2. There should not be any OBJECT or STRUCTURE on or near the heater. Minimum Distance must always be KEPT as follows:
To Left-hand or Right-hand sides or ABOVE the heater: 0.5 m In FRONT of the heater: 0.6 m
3. Installation and subsequent maintenance or safety inspection, which should beconducted at least once a year, must be carried out by Registered Gas Installer (RGI)employed by Registered Gas Contractor (RGC).
4. For enquiry/emergency services, please callxxx Co.
Telephone xxxx xxxx xxxx xxxx Fax xxxx xxxx
此 外 , 亦 須 向 購 入 或 接 收 熱 水 爐 擁 有 權 /使 用 權 的 發 展 商 /佔 用 人 /業 主 /
租 戶 /客 戶 寄 出 中 英 文 的 警 告 告 示 /信 息 。 上 述 告 示 /信 息 須 包 括 但 不 限
於 以 下 內 容 :
(i) 說 明 熱 水 爐 屬 戶 外 式 , 故 須 在 任 何 時 間 均 保 持 永 久 空 氣 流 通 的
字 句 ;
(ii) 標 明 無 障 礙 物 範 圍 , 並 列 明 尺 寸 ;
(ii i) 須 由 註 冊 氣 體 工 程 承 辦 商 聘 用 的 註 冊 氣 體 裝 置 技 工 進 行 安 裝 、
定 期 維 修 及 年 度 檢 查 , 並 須 列 明 註 冊 氣 體 工 程 承 辦 商 的 聯 絡 /緊
急 電 話 號 碼 。
24
附 錄 E
戶 外 式 氣 體 熱 水 爐 進 口 商 的 紀 錄 管 理
供 應 商 須 在 熱 水 爐 的 使 用 壽 命 期 內 妥 善 保 存 熱 水 爐 的 完 整 紀 錄 , 氣 體
安 全 監 督 在 有 需 要 時 會 查 閱 有 關 紀 錄 。 紀 錄 須 包 括 但 不 限 於 以 下 內
容 :
初 次 裝 置 、 測 試 及 校 驗
(i) 熱 水 爐 的 位 置 ;
(ii) 竣 工 圖 則 及 照 片 ;
(ii i) 熱 水 爐 的 技 術 細 節 ;
(iv) 測 試 及 校 驗 報 告 。
定 期 檢 查 及 維 修
(i) 檢 查 報 告 , 包 括 符 合 規 定 核 對 表 ;
(ii) 維 修 /事 故 紀 錄 ;
(ii i) 氣 體 安 全 監 督 要 求 的 其 他 文 件 。
25
附錄 G
有關空氣的規定 – 住宅式氣體熱水爐的機動排煙安排
低位機動空氣供應 高位排氣
天然(見註 1)燃燒用具類別
所需最小氣流
升/ 秒
開口位置 機動
升/ 秒 開口最小尺寸
平方厘米
開口位置 各開口的相互位置
周圍空氣 額定熱負荷
(千瓦特) x 1.8
(見註 2)
機動產生氣流 額定熱負荷
(千瓦特) x 1.08
(見註 2)
開口下緣至地板的距
離 不 得 高 於 密 封 地
方、房間或機房的總
高度的 5%
入口所需
空氣率的
1/4 至 1/3
額定熱負荷
(千瓦特) x 5.4
(見註 2)
開口上緣至天花板
的距離不得高於密
封地方、房間或機
房的總高度的 5%
開口所處位置須能
產生遍佈整個範圍
的氣流
(參考資料:改編自 AG601)
註 :
1. 天 然 空 氣 供 應 不 可 含 機 械 排 出 的 廢 氣 。
2. 爐 具 熱 負 荷 須 包 括 整 個 範 圍 內 所 有 爐 具 (包 括 使 用 其 他 燃 料 的 爐 具 )的 熱 負 荷 總 和 。
26
THE GOVERNMENT OF THE
HONG KONG SPECIAL ADMINISTRATIVE REGION
INSTALLATION REQUIREMENTS FORDOMESTIC GAS WATER HEATERS
( RATED HEAT INPUT UP TO 70 kW )
CODE OF PRACTICE GU 03
October 2001Issue 2
CONTENTS
Page
1. Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Scope and Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Selection and Siting of Gas Water Heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5. Gas Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6. Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7. Water Supply, Discharge and Pressure Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8. Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9. Labelling and Advice to Customers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Appendix A Criteria for Installation of Domestic Gas Water Heaters . . 18
Appendix B Acceptable Locations of Room-Sealed Gas Water Heater
Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appendix C Minimum Separation Distances and Additional Restrictions for
Outdoor Gas Water Heaters ....................................................................20
Appendix D Warning Notice and Warning Message in Connection with Outdoor
Gas Water Heaters ..................................................................................23
Appendix E Record Management by Importer for Outdoor Gas Water
Heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Page
Appendix F Air Supply Openings for Room-Sealed (Natural Draught)
and Open-Flued Fanned Draught Gas Water Heaters . . . . . . . . 25
Appendix G Air Requirement – Mechanical Ventilation for Domestic
Gas Water Heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1. Foreword
1.1 The purpose of this Code of Practice is to provide guidelines to gas appliance
importers and suppliers, registered gas contractors and registered gas installers
concerning the installation requirements for domestic gas water heaters in Hong Kong.
This Code of Practice (hereinafter referred to as this Code) is approved and issued by
the Gas Authority in accordance with Section 9 of the Gas Safety Ordinance, Cap. 51.
1.2 The guidelines contained in this Code should not be regarded as exhaustive. It is not
intended to relieve persons from undertaking the work of their statutory
responsibilities in accordance with safety legislation.
1.3 This Code has a special legal status. Although failure to observe any advice
contained in this Code is not in itself an offence, that failure may be taken by a court in
criminal proceedings as a relevant factor in determining whether or not a person has
breached any of the provisions of the regulations to which the advice relates.
1.4 All gas installation work carried out in Hong Kong shall be in accordance with the Gas
Safety Ordinance, Cap. 51 with particular reference to:-
(a) Gas Safety (Gas Supply) Regulations, Cap. 51;
(b) Gas Safety (Installation and Use) Regulations, Cap. 51;
(c) Gas Safety (Miscellaneous) Regulations, Cap. 51;
(d) Gas Safety (Registration of Gas Installers and Gas Contractors) Regulations, Cap.
51 and
(e) Gas Safety (Registration of Gas Supply Companies) Regulations, Cap. 51.
1.5 Additionally the undernoted regulations shall apply as appropriate:-
(a) Regulation 35A of the Building (Planning) Regulations, Cap. 123F;
(b) Waterworks Regulations, Cap. 102 and
(c) Electricity (Wiring) Regulations, Cap. 406.
1.6 This Code must be read in conjunction with the manufacturer’s
instructions and shall not supersede such instructions unless the latter
conflict with statutory provisions. Attention is also drawn to the
current edition of the undernoted regulations and codes of practice:-
1
(a) Code of Practice GU05 – Approval of Domestic Gas Appliances;
(b) Code of Practice GU09 – Low Pressure Regulators for Supplying Gas from LPG
Cylinders having less than 40 litres Water Capacity;
(c) The Hong Kong & China Gas Co. Ltd.’s Operating Procedures - Service:
Installation of Domestic Appliances, HKCG/SER/OP7;
(d) Code of Practice for the Electricity (Wiring) Regulations, Cap. 406;
(e) Hong Kong electricity supply companies’ policy requirements, supply rules,
installation guides and codes of practice and
(f) International/national standards referred to in Section 1.7.
1.7 The following international/national standards are for reference:-
BS 5440-1 Installation and maintenance of flues and ventilation for gas
appliances of rated input not exceeding 70 kW net (1st, 2nd and 3rd
family gases) – Part 1: Specification for installation and maintenance
of flues, British Standards Institution
BS 5440-2 Installation and maintenance of flues and ventilation for gas
appliances of rated input not exceeding 70 kW net (1st, 2nd and 3rd
family gases) – Part 2 : Specification for installation and
maintenance of ventilation for gas appliances, British Standards
Institution
BS 5546 Specification for installation of hot water supplies for domestic
purposes, using gas-fired appliances of rated input not exceeding 70
kW, British Standards Institution
AG 601 Gas Installations, The Australian Gas Association
1.8 This Code has been prepared by the Gas Authority in consultation with registered gas
supply companies, registered gas contractors, importers and suppliers of domestic gas
appliances in Hong Kong.
2
2. Scope and Terminology
2.1 This Code covers the new installation of instantaneous type gas water heaters and
storage type gas water heaters which are designed, or intended, to be used in domestic
premises irrespective or whether they are so used. It applies to gas water heaters
which burn gas types defined in Section 2 of the Gas Safety Ordinance, Cap. 51.
2.2 The gas water heaters, having a rated heat input up to 70kW, are to be of a type and
model approved by the Gas Authority in accordance with the Code of Practice GU05
before their installation takes place (subject to enactment of new legislation
concerning approval of domestic gas appliances).
2.3 Terminology
2.3.1 Definitions of gas water heater types:-
“balanced flue” a room-sealed gas water heater incorporating an air
inlet-product outlet terminal designed to be exposed
on an external wall.
“fanned draught” a gas water heater with a flue system in which the
draught is produced by a fan.
“flueless” a gas water heater designed for use without
connection to a flue conveying combustion products
from spaces within the outer building wall of premises
to external air.
“instantaneous” a gas water heater in which water is heated only as it
flows to the point of delivery.
“natural draught” a gas water heater with a flue system in which the
draught is provided by the thermal force arising from
the heat of the products of combustion.
“open-flued” a gas water heater designed to be connected to a flue
system, its combustion air being drawn from the room
or internal space in which it is installed.
3
“outdoor” a gas water heater that is designed, or intended to be
used, for supply of hot water to a dwelling and only
installed in a defined outdoor environment in the
manner prescribed under this Code. In the case of an
installation not connected to a flue, it should be
located in a permanently well-ventilated open area
external to the outer building wall/boundary, but
within the designated property line (as shown in the
Building Plan approved by the Buildings Authority)
under the jurisdiction of the responsible person(s), and
within which inhabitation is strictly prohibited.
“room-sealed” a gas water heater which, when in operation, has the
combustion air inlet and the combustion products
outlet isolated from the room in which the appliance is
installed.
“storage” a gas water heater in which a volume of water is
heated under thermostatic control and stored for use
when required.
2.3.2 Other definitions:-
“domestic gas appliance”
as defined under the Gas Safety Ordinance, Cap. 51,
means a gas appliance (construed as gas water heater
in this Code) which is designed or intended to be used
primarily in domestic premises, irrespective of
whether it is so used.
“flame failure protection”
an integral control device responsive to flame
properties which by means of detecting the presence
of a nominated flame will cause the gas supply to the
domestic gas water heater burner(s) to shut off safely
in the event of ignition failure or inadvertent flame
extinction.
4
“Gas Authority” the Authority appointed under Section 5 of the Gas
Safety Ordinance, Cap. 51.
“importer” a company in Hong Kong (as defined in Section 2 of
the Gas Safety Ordinance, Cap. 51) engaged in the
business of importation of domestic gas water heaters
for use in Hong Kong.
“overheat protection”
a non-adjustable temperature actuated device designed
to protect a gas water heater and its surroundings in
the event of failure of the normal means of
temperature control.
“Registered Gas Contractor”
means a person or a company who as a business
carries out gas installation work and is registered
under the Gas Safety Ordinance, Cap. 51.
“Registered Gas Installer”
means an individual who personally carries out gas
installation work and is registered under the Gas
Safety Ordinance, Cap. 51.
“supplier” a company in Hong Kong (as defined in Section 2 of
the Gas Safety Ordinance, Cap. 51) engaged in the
supply of gas water heaters to end users.
5
3. Selection and Siting of Gas Water Heaters
3.1 The permitted siting of gas water heaters to be installed in various room types is
outlined in Appendix A, GSO/IG/23-3/00.
3.2 For any new installation, room-sealed gas water heaters shall always be the first choice.
When this is not feasible in locations, other than bathrooms or shower rooms, then
fanned draught models should be used.
3.3 Room-sealed Models
(a) Room-sealed gas water heaters shall always be the first choice for new and
replacement installations.
(b) The location of apertures for room-sealed balanced flue heaters in a new
building is controlled under Regulation 35A of the Building (Planning)
Regulations, Cap. 123F. Whenever a suitable aperture is provided, only a
room-sealed model shall be installed and that aperture must be used, in
accordance with Regulation 27 of the Gas Safety (Installation and Use)
Regulations.
(c) The requirements contained in Regulation 35A of the Building (Planning)
Regulations, Cap. 123F mainly apply to the siting of room-sealed apertures in
new buildings. Appendix B outlines the acceptable locations of room-sealed
gas water heater terminals. It is recognized that the provision of suitable
apertures may, however, be difficult in existing dwellings and therefore fanned
draught room-sealed models may offer a practical solution in the circumstance.
(d) Room-sealed gas water heaters can be installed in most locations although their
installation in bedrooms or living rooms is not preferred.
(e) Particular attention should be given to those provisions within the Regulation
35A of the Building (Planning) Regulations, Cap. 123F and Appendix B of this
Code concerning installations in lightwells. Where the dispersion of
combustion products is likely to be difficult owing to building configurations,
then the use of fanned draught room-sealed models will be preferred.
6
3.4 Open-flued Natural Draught Models
In accordance with Regulation 36 of the Gas Safety (Installation and Use) Regulations,
Cap. 51, instantaneous gas water heater of this type shall not be installed.
3.5 Open-flued Fanned Draught Models
(a) In siting this type of gas water heater, the first choice should be to locate it in the
kitchen, utility or balcony area with good ventilation. Since this heater requires
air for combustion from the space in which it is located, reference shall be made
to Section 4 of this Code to ensure adequate permanent ventilation is provided at
all times.
(b) This type of gas water heater shall not be installed in bedrooms or living areas.
(c) New installation of this type of gas water heater for bathroom or shower room is
not permitted. (Room-sealed models must be used for new installation and the
requirements are in Section 3.3 of this Code). Replacement of open-flued
fanned draught models will only be permitted on the basis of like for like
exchange in accordance with Regulation 27(3) of the Gas Safety (Installation
and Use) Regulations, Cap. 51.
3.6 Flueless Models
In accordance with Regulation 35 of the Gas Safety (Installation and Use) Regulations,
this type of gas water heater shall not be installed.
3.7 Outdoor Models
(a) General
Gas water heaters may be installed outside premises, designated outdoor models
not connected to a flue shall only be installed in strict compliance with
requirements as detailed in this Section.
Outdoor models not connected to a flue shall only be provided on a “supply-
install-and-maintain” basis by the importer of the appliance.
7
The importer, who shall also be the supplier, shall ensure that the design,
construction and installation of the outdoor gas water heater not to be connected
to a flue fully complies with the conditions and requirements in this Code,
including but not limited to sections 2.2 and 3.7 in particular.
(b) Installation Requirements for Outdoor Gas Water Heaters Not Connected to a
Flue
(i) Prohibited Locations
The heater shall not be wall-mounted and shall not be installed at any one
of the following locations:
(1) within or adjacent to a balcony;
(2) in a light well with obstruction to the vertical flow of air or without
vent to external air below the lowest terminal;
(3) in a re-entrant with obstruction to the vertical flow of air;
(4) in the underside of any structures, e.g. stairway;
(5) in a basement or a lower floor below grade;
(6) in a temporarily or permanently covered, sheltered or enclosed area
such as housing, box/chamber, etc.;
(7) in a poorly ventilated area; or
(8) in proximity to air inlet or suction of other utility services.
(ii) Permitted Conditions
The heater shall only be installed in compliance with the following two
conditions :-
(1) in a well-ventilated designated location as defined below that does
not have any temporary or permanent structures or obstacles in it
other than the mounting:
in an open-top yard at ground level above grade; or
on an open-top flat roof; or
on an open-top podium; and
(2) on solid mounting complete with a safe and rigid non-combustible
plinth or structure and external to the outer building wall/boundary
and in such a way that there is always an open-top , well ventilated
8
sterile zone of no less than 500 mm on each side of the heater and no
less than 600 mm on the front side of the heater.
(c) Mounting of Heater
The heater shall not be wall-mounted. It shall be mounted in such an
orientation that its flue terminal always discharges flue gas away from the outer
building wall/boundary and to an external open area above grade. Adequate
clearance shall be maintained between the outer building wall/boundary and the
rear side of the heater. The heater shall be of floor-mounted type in accordance
with the manufacturer’s instructions.
(d) Locational Restrictions
Minimum separation distances and additional restrictions shall apply in
accordance with Appendix C – “Minimum Separation Distances and Additional
Restrictions for Outdoor Gas Water Heaters” .
(e) Warning Notices/Messages
A warning label of durable, weatherproof material and ink with minimum size
130 mm x 130 mm containing information in both Chinese and English of
character font size 11 or larger shall be affixed onto the heater in a conspicuous
location. It shall incorporate information including but not limited to those
listed in Appendix D – “Warning Notice and Warning Message in Connection
with Outdoor Gas Water Heaters” .
In addition, a warning notice/message in both Chinese and English containing
the same information shall be sent to the
developer/occupier/owner/tenant/customer who purchases or takes over the
ownership/use of the heater with acknowledgement kept for record purposes.
Illustrative sample warning notice and sample warning message are given in
Appendix D.
(f) Installation, Testing, Commissioning, Inspection and Maintenance
9
The importer shall be responsible for arranging a Registered Gas Contractor to
conduct the installation, testing, commissioning, subsequent regular inspections
and maintenance of individual units of each installed heater. At least one
inspection shall be conducted every year to verify that all the prescribed
conditions under Section 3.7 (a) to (e) have been complied with. The
inspection report shall be kept for record purposes. It shall record all inspection
results in accordance with a compliance checklist and shall bear the signature of
the registered gas installer who carried out the work.
(g) Record Management
Full records, which may be inspected by the Gas Authority as and when required,
shall be properly maintained by the importer within the life time of the heater,
including but not limited to those outlined in Appendix E.
10
4. Ventilation
4.1 Air Supply
(a) In accordance with Regulation 23 of the Gas Safety (Installation and Use)
Regulations, Cap. 51, a gas water heater shall be installed in a location with
adequate permanent ventilation for complete combustion of gas, for proper
flueing and to maintain the ambient temperature of the immediate surrounding
within safe limits under normal operating conditions.
(b) The quality of air supply shall not be contaminated with combustion products, or
contain chemical or inflammable vapours which could affect combustion.
(c) The minimum room/compartment ventilation requirements for each type of gas
water heater are outlined in Appendix A, GSO/IG/23-3/00. Where a natural
ventilation system is used, there shall be provision for permanent low and high
level openings according to Appendix A, GSO/IG/23-3/00. The openings shall
be fitted with grilles/louvres of minimal resistance and shall be sited so that they
are not prone to blockage or flooding.
(d) Where room-sealed gas water heaters are installed in compartments, provision
for heat relief in the form of ventilation should be made (see minimum
compartment ventilation in Appendix A, GSO/IG/23-3/00).
(e) Appendix F illustrates diagrammatically the air supply openings required for
room-sealed (natural draught) and open-flued fanned draught gas water heaters.
(f) For air supply and ventilation to a room housing storage type gas water heater(s),
reference should be made to BS 5440 or equivalent and the manufacturer’s
instructions for compliance.
(g) Regulations 23 and 24(4) of the Gas Safety (Installation and Use) Regulations,
Cap. 51 shall be satisfied at all times. When mechanical ventilation is deemed
required, all air inlet and extraction fans shall be fitted with fail-safe automatic
controls causing safety shut-down or lock-out of the heater in the event of the
failure of the inlet and extraction air flow. The air supply to the gas water
heater shall be in accordance with the manufacturer’s instructions and in the
absence of which, shall be provided with reference to Appendix G or equivalent
international/national standards.
11
4.2 Flueing
(a) Regulations 24 of the Gas Safety (Installation and Use) Regulations, Cap. 51
shall be satisfied at all times. The flue termination requirements for each type
of gas water heaters are outlined in Appendix A, GSO/IG/23-3/00.
(b) For fanned draught gas water heaters, reference should also be made to the
manufacturer’s instructions regarding the maximum length of flue pipe,
maximum number of bends, etc.
(c) For storage type gas water heaters, reference should be made to BS 5440 or
equivalent and the manufacturer’s instructions.
12
5. Gas Supply
5.1 All gas installation work shall be carried out in accordance with Parts II, IV and V of
the Gas Safety (Installation and Use) Regulations, Cap. 51.
5.2 Attention is drawn to the necessity for ensuring that the gas water heater is compatible
with the respective gas type and supply pressure to which it is being connected.
Reference should also be made to the manufacturer’s instructions in this regard.
5.3 Metallic piping shall be used to connect a gas water heater to the gas supply. A gas
isolation cock, which cannot be accidentally operated, shall be fitted close to the gas
water heater. The number of fittings and connections used when installing gas water
heaters should be kept to a minimum.
5.4 The installation, soundness testing and purging procedures of the respective registered
gas supply company in Hong Kong shall be followed.
5.5 In the case of storage type water heaters, provision shall be made to ensure
overpressurisation shall not occur within the storage container (see Section 7.4) in the
event of thermostat failure. This may include a temperature or pressure activated
safety device to isolate the gas supply in such circumstance.
13
6. Electrical Requirements
6.1 The electrical supply and its protection must comply with the current requirements laid
down in the Supply Rules of local electrical supply companies, the Code of Practice
for the Electricity (Wiring) Regulations, Cap. 406 published by the Electrical &
Mechanical Services Department and the latest edition of the Institution of Electrical
Engineers’ Wiring Regulations.
6.2 Special attention should be drawn to the installation of fanned draught gas water
heaters in bathrooms or shower rooms:-
(a) The control switch and transformer unit external to the heater shall be installed
outside the bathroom or shower room.
(b) No socket outlets shall be provided inside the bathroom or shower room.
(c) The characteristics of the protection devices and earthing arrangement shall
comply with the relevant regulations and codes of practices referred to in Section
6.1 of this Code especially concerning protection against electric shock from
indirect contact with a live conductor. The installation of a safety device, such
as a residual current device, will ensure that the disconnection of the electrical
supply occurs within 0.4 second of the indirect contact taking place.
14
7. Water Supply, Discharge and Pressure Release
7.1 The gas water heater shall satisfy the relevant provisions under the Waterworks
Regulations, Cap. 102.
7.2 The gas water heater should be suitable for use under the static head of fresh water
supply normally available in Hong Kong, and/or should be compatible with the water
supply pressure to which it is being connected, as specified by the Water Authority.
7.3 It is desirable that hot water pipes should be suitably insulated for heat conservation
purposes, where applicable.
7.4 Unvented storage gas water heaters shall be provided with means to prevent
overpressure in the event of thermostat failure, to include a pressure relief valve and a
high temperature cut-out device or temperature relief valve. The outlet of relief
valve(s) shall not be restricted.
15
8. Commissioning
8.1 The installed gas water heater shall be commissioned in accordance with Regulation 30
of the Gas Safety (Installation and Use) Regulations, Cap. 51.
8.2 An inspection of completed installation work should be carried out in the first instance
to ascertain that the gas water heater has been installed in accordance with the
manufacturer’s instructions and this Code.
8.3 The gas installation pipework and gas water heater shall then be pressure tested for
soundness.
8.4 After the installation passed the pressure test, purging operation shall be proceeded.
The purging shall be carried out according to the manufacturer’s instructions.
8.5 The whole of the water system should be thoroughly flushed out ensuring that special
instructions by the manufacturer are followed.
8.6 The gas water heater should be lit in the sequence described in the manufacturer’s
instructions.
8.7 All the gas water heater controls, both manual (front panel knobs) and automatic
(thermostats, flame failure protection, etc.), should be checked in order to ensure they
are functioning correctly. The manufacturer’s instructions should be referred to for
relevant details.
8.8 For fanned draught gas water heaters, safety devices which operate in the event of fan
failure should be checked to ensure compliance with manufacturer’s specifications.
16
9. Labelling and Advice to Customers
9.1 Labelling
The Registered Gas Installer should ensure that any labels provided or required by the
manufacturer which describe user’s operating procedures, safety information, warning
notices, etc are in both Chinese and English languages and affixed onto the gas water
heater at a prominent position. A special label should be affixed to outdoor type gas
water heaters, the requirements are outlined in Section 3.7 (e) of this Code.
9.2 Advice to Customers
(a) The customers should be provided with the user’s instructions in both Chinese
and English supplied by the manufacturer in accordance with Regulation 26 of
the Gas Safety (Installation and Use) Regulations, Cap. 51.
(b) The correct operation procedures for the gas water heater and its control should
be demonstrated to the customers before use. The customers should be advised
of any precautions necessary for the safe operation of the gas water heater.
(c) The customers should be advised that for continued efficient and safe operation
of the gas water heater, it is important that regular servicing is carried out at least
once a year by a Registered Gas Installer in accordance with the manufacturer’s
instructions and the relevant codes of practice.
(d) The customers with outdoor gas water heaters installed should be given special
advice as outlined in Section 3.7(e) of this Code.
17
Appendix A
(GSO/IG/23-3/00)
Criteria for Installation of Domestic Gas Water Heaters
- This Code shall be read in conjunction with the manufacturer’s instructions and shall not supersede such
instructions unless the latter conflicts with statutory provisions.
- For any new installation, room-sealed gas water heaters must always be the first choice – when this is not feasible
in locations, other than bathrooms/shower rooms, then fanned draught models should be used.Requirements for Each Type of Gas Water Heater
Room Type and InstallationRoom-Sealed Open-Flued Fanned Draught
New NoBathroom orShower Room Replacement
YesYes
Provided it was installed before 1.1.94and to be replaced by another open-fluedfanned draught type
NewKitchen orUtility Replacement
Yes Yes
NewBalconyReplacement
Yes Yes
NewBedroom orLiving Room Replacement
Not Preferred No
Minimum Room Ventilation (Note 1)
Free air vent area/kW 7 kW-(Note 2) 5 1/min
12 kW - 7 1/min
16 kW - 9 1/min
20 kW - 11 1/min
24 kW - 13 1/min
28 kW - (Approx.Hot WaterCapacity)
70 kW
NotRequired
5 cm2/kW for heater with rated heatinput in excess of 7 kW and up to 70 kW
High Level 10 cm2/kW * 10 cm2/kWToRoom Low Level 10 cm2/kW * 20 cm2/kW
High Level 5 cm2/kW * 5 cm2/kW
MinimumCompartmentVentilation(Free air ventarea/kW)(Note 3)
ToOutside Low Level 5 cm2/kW * 10 cm2/kW
FlueTermination
Natural Draughtshall comply with Regulation 35A of theBuilding (Planning) RegulationsFanned Draughtminimum 300 mm below any opening
Minimum 300 mm below any openinginto a building
* The requirement is for natural draught models only. As for fanned draught models, reference should be made to
the manufacturer’s instructions.
Note 1 - Room ventilation means ventilation communicating directly with outside air.
Note 2 - Permanent opening shall be an air vent without obstruction.
Note 3 - Compartment ventilation means ventilation not communicating directly with outside air.
18
Appendix B
Acceptable Locations of Room-Sealed Gas Water Heater Terminals
EXTERNAL VIEWDimension Minimum
DistanceA From any corner of building 300 mm*B From any adjacent opening
into building300 mm
C From facing wall or boundary 1 500 mm*D Minimum plan width of re-
entrant1 500 mm*
E Below a balcony or similarprojection
300 mm*
F&G
Light well plan area (F x G)10 or less storeys11-19 storeys20 or more storeys
3 000 mm4 000 mm5 000 mm
* May be reduced for fanned draught models.See manufacturer’s instructions.
Light WellsNo obstruction to the vertical flow of air.Vented to external air, below the lowest terminal. The vents to have a minimum area of 0.05 m2 for each terminalfacing into the light well. Minimum internal dimension of vents to be 200 mm.Additional vents to be provided where air conditioners take air from light well.See limitations on plan dimensions (F x G).
Re-entrantsNo obstruction to the vertical flow of air.Tie beams should not reduce the open area of the face of the re-entrant by more than 20% at any storey[i.e. Y ≦ 20% (X + Y)].See limitation on minimum plan width (D).
INTERNAL VIEWDimension Minimum
KNQ
Unobstructed area 100 mm150 mm50 mm
P Height above floor 200 mm(2 400 mm max)
L x M Standard size
Non standard
380 x 380 mmor
240 x 240 mm
to suit
Unobstructed area shaded
19
Appendix C
Minimum Separation Distances and Additional Restrictions
for Outdoor Gas Water Heaters
- This Code shall be read in conjunction with the manufacturer’s instructions and shall not
supersede such instructions unless the latter conflict with statutory provisions.
Minimum separation distances are summarized in Tables 1 & 2 and the surroundings are
delineated in Figures 1 & 2. Separation distance refers to the shortest distance between the
edge of the outdoor gas water heater (hereinafter called the heater) and the nearest edge/corner
of other openings/objects.
(a) Table 1 shows the separation distances from adjacent openings such as windows, doors, etc
Minimum Separation
Distance (mm)
Dimension Description For Natural
Draft
Category
For Fanned
Draft
Category
Not above 150 500 300
> 150 to 200 1,500 500PPoint-to-point from an
opening on a lateral wall
Rating
(MJ/h)
> 200 1,500 1,500
---Horizontally in the direction of discharge for fan-
assisted models--- 1,500
Not above 150 500 300
Q
Horizontally from an
opening on a wall
behind the water heater
Rating
(MJ/h)
> 150 1,500 300
Not above 150 1,000 300
R
Vertically from an
opening on a wall
behind the water heater
Rating
(MJ/h)
> 150 1,500 300
Conversion: 1 MJ/h = 0.28 kW
20
(b) Table 2 shows the separation distances from adjacent objects
Dimension Description Minimum Separation Distance
(mm)
S From a return wall or external corner 500
T From another heater or appliance (side) 500
X From facing wall or boundary 1,500
Y From facing obstruction 600
Z Below eave or similar projection 500
---From gas meter, electric meter or devices thatmay generate sparks 1,000 and not directly below
--- From ground level to flue terminal 500
--- From pipes 150
--- From combustibles 500
The front, top and sides of the heater shall be unobstructed at all times. Should it beinstalled under an eave or similar projection, the projected area under the eave or similarprojection shall not cover the heater entirely. The flue terminal of the heater should notdirectly point to the inlet or outlet or ducting of other utilities or appliances, e.g. split type airconditioners.
(c) Figure 1 shows the plan view of a sterile zone of no less than 500 mm on each side of theheater and no less than 600 mm to the front of the heater:
(d) Figure 2 shows the minimum separa
Outdoor type gas water heater
Direction of
wall /boundar
Sterile
5 00
5 00tion distance
21
gas dischar
y, facing ex
6 00
s depicted in Tables 1 and 2.
ge (away from building
ternal open area)
22
Appendix D
Warning Notice and Warning Message in Connection with Outdoor Gas Water Heaters
Sample warning notice to be affixed to an outdoor gas water heater not connected to a flue is givenbelow:-
安 全 告 示 / 指 示 S A F E T Y N O T I C E / M E S S A G E警 告
1. 本熱水器是戶外式燃氣熱水器。 衹准於屋宇以外的、露天的特定地方安裝。 必
須確保周圍空氣流通。阻礙通風,會有性命危險。
2. 在本熱水器所在處之左方、右方或頂方距離不少於 0.5 米內及前方不少於 0.6 米
範圍內,不得有任何障礙物或建築物之部份存在。
3. 須由政府註冊氣體工程承辦商聘用之註冊氣體裝置技師進行安裝及作定期安全檢
查及維修。每年至少一次。
4. 如有任何查詢/緊急事故,請致電
xxx 公 司
電話 xxxx xxxx xxxx xxxx 傳真 xxxx xxxx
C A U T I O N
1. This is an OUTDOOR type gas water heater. It must ONLY be installed in a
prescribed outdoor open space and must be well-ventilated. It is hazardous to life if
ventilation is impaired.
2. There should not be any OBJECT or STRUCTURE on or near the heater.
Minimum Distance must always be KEPT as follows:
To Left-hand or Right-hand sides or ABOVE the heater: 0.5 m
In FRONT of the heater: 0.6 m
3. Installation and subsequent maintenance or safety inspection, which should be
conducted at least once a year, must be carried out by Registered Gas Installer (RGI)
employed by Registered Gas Contractor (RGC).
4. For enquiry/emergency services, please call
xxx Co.Telephone xxxx xxxx xxxx xxxx Fax xxxx xxxx
Additionally, a warning notice/message in both Chinese and English shall be sent to thedeveloper/occupier/owner/tenant/customer who purchases or takes over the ownership/use of theheater. It shall incorporate information including but not limited to the following:-
(i) Statement indicating that the heater is of outdoor type, which must require permanent openventilation at all times;
(ii) Specified sterile zone complete with dimensions;(iii) Installation, regular maintenance and annual inspections to be undertaken by a Registered
Gas Installer employed by a Registered Gas Contractor is a must; and contact/emergencytelephone number of Registered Gas Contractor.
23
Appendix E
Record Management by Importer for Outdoor Gas Water Heaters
Full records, which may be inspected by the Gas Authority as and when required, shall be properly
maintained by the supplier within the life time of the heater, including but not limited to the
following:-
New Installation, Testing and Commissioning
(i) Location of heater;
(ii) As-built drawings and photographs;
(iii) Technical details of heater;
(iv) Testing and commissioning reports.
Regular Inspections and Maintenance
(i) Inspection reports including compliance checklists;
(ii) Maintenance/incident records;
(iii) Other documents as required by the Gas Authority.
24
Appendix F
Air Supply Openings for Room-Sealed (Natural Draught) and
Open-Flued Fanned Draught Gas Water Heaters
Type
Location
Room-Sealed *(Natural Draught)
Open-FluedFanned Draught
In room
In compartmentopen to room
In compartmentopen to outside
In balcony
* For room-sealed fanned draught gas water heaters, reference should be made to
manufacturer’s instructions.
25
26
Appendix G
AIR REQUIREMENTS –MECHANICAL VENTILATION FOR DOMESTIC GAS WATER HEATER
Low level mechanical air supply High level exhaust
Natural (See Note 1)
Type of
Appliance burner Minimum air
flow required L/s
Location
of opening
Mechanical
L/s Size of opening (min.)
cm2
Location of
opening
Position of
openings in
relation to each
other
Atmospheric
Rated heat input
(kW) x 1.8
(See Note 2)
Fanned induced
draught
Rated heat input
(kW) x 1.08
(See Note 2)
The distance
between the
lower edge of the
opening and the
floor shall not be
more than 5% of
the total height
of the enclosure,
room or plant
room
Between
1/4 and 1/3
of the rate
of inlet air
required
Rated heat input
(kW) x 5.4
(See Note 2)
The distance
between the top
edge of the
opening and the
ceiling shall not
be more than
5% of the total
height of the
enclosure, room
or plant room
Opening to be
located to
provide a flow
of air across the
area
(Source : Adapted from AG601)
NOTES :
1. A natural air supply with a mechanical exhaust is not permitted.
2. Appliance input is to include the total of all appliances in the area including those using other fuels.