guidance on rcds

Licensed copy: David,Fri Feb

RESIDUAL CURRENT DEVICE (RCD) R R101-41Types of

Electrical Safety CouncilRESIDUAL CURRENT DEVICE (RCD) - Types of

Contents

1. Introduction

2. General

3. RCCB (residual current operated circuit-breaker without integral overcurrent protection)

4. RCBO (residual current operated circuit-breaker with integral overcurrent protection)

5. SRCD (socket-outlet incorporating an RCD)

6. Portable RCD

7. RCD formed by an association of devices

1. Introduction

This topic explains the different types of residual current device (RCD) normally used.

2. General

An RCD monitors the algebraic sum of the currents in the line and neutral conductors (theresidual current) at the point at which it is installed in a circuit, and mechanically interruptsthe circuit when this sum attains a predetermined value (the rated residual operatingcurrent ).

The following definition is given in Part 2 of BS 7671:

Residual current device (RCD) is the generic name for a range of devices including:

RCCB (residual current operated circuit-breaker without integral overcurrentprotection)

RCBO (residual current operated circuit-breaker with integral overcurrent protection) SRCD (socket-outlet incorporating an RCD) Portable RCD An RCD formed of a suitable association of devices including current transformers, a

residual current sensor, a test button and a circuit-breaker.

Residual current device (RCD). A mechanical switching device or association ofdevices intended to cause the opening of the contacts when the residual currentattains a given value under specified conditions.

In 18 14:51:45 2011

ELECTRICAL SAFETY COUNCIL TECHNICAL MANUAL July 2008 1 of 6



Electrical Safety CouncilRequirements on selection and erection of RCDs is given in Regulation Group 531.2.

Information on discrimination of RCDs in series is given in Topic R101-5.

Further information on the requirements of RCDs is given in Topic R101-29.

3. RCCB (residual current operated circuit-breaker without integral overcurrent protection)

A residual current operated circuit-breaker without integral overcurrent protection (RCCB)is not designed to perform the function of protection against overcurrent (overload currentor fault current).

A circuit, or circuits, controlled by an RCCB must therefore be provided with devices forprotection against overcurrent, such as suitable circuit-breakers or fuses.

Residual current operated circuit-breakers without integral overcurrent protection shouldcomply with BS EN 61008 Specification for residual current operated circuit-breakerswithout integral overcurrent protection for household and similar uses (RCCBs).

Examples of RCDs for DIN rail mounting for use in an enclosure such as a distribution board or consumer unit. From left to right, a two-pole device and a four-pole device

Photograph courtesy of Legrand Electric Limited 18 14:51:45 2011




Electrical Safety Council4. RCBO (residual current operated circuit-breaker with integral overcurrent protection)

A residual current operated circuit-breaker with integral overcurrent protection (RCBO) isdesigned to perform the function of protection against overcurrent, as well as that of aresidual current device.

RCBOs are often used as circuit protective devices in consumer units anddistribution boards.

RCBO being installed into a consumer unit

Photograph courtesy of MK Electric Limited

Residual current operated circuit-breakers with integral overcurrent protection shouldcomply with BS EN 61009 Specification for residual current operated circuit-breakers withintegral overcurrent protection for household and similar uses (RCBOs).

Further information on RCBOs is given in Topic R93-1. 18 14:51:45 2011




Electrical Safety Council5. SRCD (socket-outlet incorporating an RCD)

A socket-outlet incorporating a residual current device (SRCD) provides an alternative toprotecting a circuit supplying a socket-outlet by an RCD. The advantage of using an SRCDis that only the circuit that is plugged into the SRCD socket-outlet is disconnected whenthe SRCD detects an earth fault. The circuit supplying the SRCD should be unaffectedand continues to supply any other socket-outlets or SRCDs that it serves.

The disadvantage of using an SRCD is that it does not protect users against earth faults inthe SRCD supply circuit. Therefore, if an earth fault occurs in the SRCD supply circuit, afault voltage may be present on any exposed-conductive-parts of the SRCD and theequipment plugged in to it, until the fault is cleared by an upstream protective device.

SRCDs should comply with BS 7288 Specification for socket-outlets incorporating residualcurrent devices (SRCDs).

Examples of SRCDs (socket-outlets with RCDs)

Photograph courtesy of Legrand Electric Limited 18 14:51:45 2011




Electrical Safety Council6. Portable RCD

Portable RCDs incorporate a plug-pin portion and may have either a socket-outlet portionor may include terminals for external flexible cords, where appropriate. It should be notedthat such RCDs do not form part of the fixed electrical installation.

Such RCDs have a rated voltage not exceeding 250 V a.c. single-phase, a rated current notexceeding 16 A and a rated residual operating current not exceeding 30 mA.

Portable RCDs should comply with BS 7071 Specification for portable residualcurrent devices.

A rewireable portable RCD, as in Fig 1, is constructed so a cable or flexible cord can befitted or replaced using general purpose hand tools (such as a screwdriver).

Non-rewireable portable RCDs are constructed as a unit including a flexible cord whichcannot be removed by any means without making the unit permanently useless.

Portable RCDs may be provided with overload current and/or short-circuitcurrent protection.

Example of a rewireable portable RCD

Fig 1

13 A plug-pins

Flexible cord entry

for connecting

to portable RCD terminals

RESET

RCDON

RCDOFF

TEST

TEST BEFORE

USE

RCD 18 14:51:45 2011




Electrical Safety CouncilTopics referred to in this text:

R93-1 RESIDUAL CURRENT BREAKER WITH OVERCURRENT DEVICE (RCBO): GeneralR101-5 RESIDUAL CURRENT DEVICE: Discrimination of, in seriesR101-29 RESIDUAL CURRENT DEVICE (RCD): Regulatory requirements for

Topics not referred to in this text, which are related and may be of interest:

A11-17 ADDITIONAL PROTECTION: By RCDE65 ELECTRIC SHOCKF18-13 FAULT PROTECTION: Protective devices forF18-17 FAULT PROTECTION: RCD protectionR101-17 RESIDUAL CURRENT DEVICE (RCD): In split-load consumer unitsR101-19 RESIDUAL CURRENT DEVICE (RCD): In a TT systemR101-23 RESIDUAL CURRENT DEVICE (RCD): Other considerations in selectingR101-25 RESIDUAL CURRENT DEVICE (RCD): Principles of operation

BS 7671 (Requirements for electrical installations)Some of the most important requirements are found in:

Additional protection, residual current devices (RCDs) 415.1Fault protection by protective equipotential bonding and automaticdisconnection 411.3 to 411.67. RCD formed by an association of devices

The principles of operation for an RCD formed by a suitable association of devices, aresimilar to those previously described for other RCDs. Such an association of devicesmight include current transformers, a residual current sensor, a test button and acircuit-breaker. An arrangement of a residual current device formed by an association ofdevices may be required for a circuit having a load current greater than that catered for bya conventional RCD (residual current device), which usually only has a current rating ofbetween 13 A and 100 A. 18 14:51:45 2011


RCDs 531.2

RESIDUAL CURRENT DEVICE (RCD)Contents1. Introduction2. General3. RCCB (residual current operated circuit-breaker without integral overcurrent protection)4. RCBO (residual current operated circuit-breaker with integral overcurrent protection)5. SRCD (socket-outlet incorporating an RCD)6. Portable RCD7. RCD formed by an association of devices

1. IntroductionThis topic explains the different types of residual current device (RCD) normally used.

2. GeneralAn RCD monitors the algebraic sum of the currents in the line and neutral conductors (the residual current) at the point at whic...The following definition is given in Part 2 of BS 7671:Residual current device (RCD). A mechanical switching device or association of devices intended to cause the opening of the contacts when the residual current attains a given value under specified conditions.Residual current device (RCD) is the generic name for a range of devices including:

3. RCCB (residual current operated circuit-breaker without integral overcurrent protection)A residual current operated circuit-breaker without integral overcurrent protection (RCCB) is not designed to perform the function of protection against overcurrent (overload current or fault current).A circuit, or circuits, controlled by an RCCB must therefore be provided with devices for protection against overcurrent, such as suitable circuit-breakers or fuses.Residual current operated circuit-breakers without integral overcurrent protection should comply with BS EN 61008 Specification for residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs).Examples of RCDs for DIN rail mounting for use in an enclosure such as a distribution board or consumer unit. From left to right, a two-pole device and a four-pole device

4. RCBO (residual current operated circuit-breaker with integral overcurrent protection)A residual current operated circuit-breaker with integral overcurrent protection (RCBO) is designed to perform the function of protection against overcurrent, as well as that of a residual current device.RCBOs are often used as circuit protective devices in consumer units and distribution boards.RCBO being installed into a consumer unitResidual current operated circuit-breakers with integral overcurrent protection should comply with BS EN 61009 Specification for residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs).Further information on RCBOs is given in Topic R93-1.

5. SRCD (socket-outlet incorporating an RCD)A socket-outlet incorporating a residual current device (SRCD) provides an alternative to protecting a circuit supplying a socke...The disadvantage of using an SRCD is that it does not protect users against earth faults in the SRCD supply circuit. Therefore, ...SRCDs should comply with BS 7288 Specification for socket-outlets incorporating residual current devices (SRCDs).Examples of SRCDs (socket-outlets with RCDs)

6. Portable RCDPortable RCDs incorporate a plug-pin portion and may have either a socket-outlet portion or may include terminals for external flexible cords, where appropriate. It should be noted that such RCDs do not form part of the fixed electrical installation.Such RCDs have a rated voltage not exceeding 250 V a.c. single-phase, a rated current not exceeding 16 A and a rated residual operating current not exceeding 30 mA.Portable RCDs should comply with BS 7071 Specification for portable residual current devices.A rewireable portable RCD, as in Fig 1, is constructed so a cable or flexible cord can be fitted or replaced using general purpose hand tools (such as a screwdriver).Non-rewireable portable RCDs are constructed as a unit including a flexible cord which cannot be removed by any means without making the unit permanently useless.Portable RCDs may be provided with overload current and/or short-circuit current protection.Example of a rewireable portable RCDFig 1

7. RCD formed by an association of devicesThe principles of operation for an RCD formed by a suitable association of devices, are similar to those previously described fo...Topics referred to in this text:Topics not referred to in this text, which are related and may be of interest:BS 7671 (Requirements for electrical installations) Some of the most important requirements are found in:

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputCondition () /PDFXRegistryName (http://www.color.org) /PDFXTrapped /Unknown

/Description >>> setdistillerparams> setpagedevice

guidance on rcds

Documents

current transformers

rcd portable rcd

interruptsthe circuit

aresidual current sensor

generalan rcd

suitable circuitbreakers

topic r101

mechanical switching