herramientas de diagnostico caterpillar

Diagnostic ToolQuick Reference

Caterpillar Service Technology Group 30-Jan-02

171-4400 Communication Adapter II Gp.

- Required PC software is included - CE Compliant- 4 times faster flash times with J1939 - Flash memory, no SPM- 4 DataLinks: ATA(J1708) RP1210 Compatible, Cat Data Link, J1939, DeviceNet (CAN)- Replaced 7X1700 Communications Adapter I- For more information, see NEHS0758 Getting Started Guide

Allows PC to communicate with engine data linkFunction:

177-8910 Power Link Group

- Designed to accommodate a wide range of tractors & implements- Measures tractors with up to 18,160kg (40,000lbs) drawbar pull and 36,320kg (80,000lbs) max rating- Measures true ground seep and draft load- For more information, see PELJ0045 IRM & NEHS0768 Tool Operating Manual

Measures actual drawbar horsepower of Ag TractorsFunction:

187-8520 Wireless ET Link Group

- Allows full ET functionality without being connected to the machine- 1.5 Mile range (Line of site) - Works with CA I & CA II- 2.4 GHz transmit and receive frequency - No license required- For more information, see PELJ0057 IRM

Wireless ET CommunicationsFunction:

189-1720 Analog Gauge Tester Gp.

- Used to test and troubleshoot analog temperature, pressure, fuel, & articulatoin gauges- Analog guage specifications provided- Decrease troubleshooting time and reduce cost by eliminating replacement of good parts- Fuse protected from electrtical overload- For more information, see PELJ0062 IRM & NEHS0786 Tool Operating Manual

Used to test analog temperature, pressure, fuel and articulated gaugesFunction:

191-3520 Pro Link Plus

- Displays and prints fault codes and log codes- Snapshot datalogger- Displays engine rating information - CE Compliant- Requires 191-3521 Caterpillar Cartridge- For more information, see PELJ0055 IRM

Display and Datalogger for On-highway truck systemsFunction:

of 24Caterpillar: Confidential GreenLast Modified: 01/30/2002

Diagnostic Tool - Quick Reference

1U-6602 Photo-Tach Gp.

- Measures RPM by directing light beam onto piece of reflective tape- RPM can be measured to and is accurate within 1 RPM- LCD viewed simultaneously while aiming the instrument- Provides low cost tachometer for general use- For more information, see SEHS8854 Special Instructions

Measures engine RPMFunction:

1U-8860 Pickup Gp. - Blowby

- Optional pickup for use with 8T-2700 Blowby/Airflow Group- Large 38 mm (1.5 in) pickup used on large engines without increasing crankcase pressure- All metal construction and alrge size makes tool suitable for permanent installation- Can also measure air velocity such as radiator cooling air flow- For more information, see SEHS8984 Service Manual

Checks blowby volume on large enginesFunction:

6V-2150 Analyzer Gp. - Starting/Charging

- For machines that have automotive type key start and a diagnostic connector- Allows one man to quickly check 14 test points in starting and charging system- Identifies deteriorated starting and charging system components before they fail- Requires 110-4645 Adapter Cable As.

Checks 14 test points in 24-volt starting and charging systemsFunction:

7X-1400 Digital Diagnostic Tool Gp.

- Displays diagnostic faults, Engine RPM, Engine Detonation Level, & Allows for calibration- Part of 146-2727 G3600 Operator Tool Gp.- Requires NEXG4511 Service Program Module

Used for monitoring engine functions and diagnostic fault codesFunction:

8T-1000 Electronic Position Indicator Gp.

- 3 separate storage memories record minimum, maximum, and difference values- Digital readout (0-1) range 0 - 25.4mm- 8T-1001 Indicator powered with internal 9-volt battery; AC power adapter available- For more information see SEHS8623 Special Instructions & NEHP5597 Brochure

Measures dynamic and static rack position & other linear measurementsFunction:

8T-2700 Blowby/Air Flow Indicator Gp.

- Volume of blowby gases very helpful in planning engine repairs- Air velocity helpful to quickly find plugged or partially restricted areas- Battery-powered digital indicator- Part of 146-2726 Maintenance Tool Gp.- For more information see SEHS8712 Special Instructions

Measures engine blowby gas & air velocity through radiatorFunction:



8T-5200 Signal Generator/Counter Gp.

- Small handheld square-wave generator- Used to simulate speed in place of magnetic speed pickup- Frequency counter when unput is pulsating- For more information, see SEHS8579

Measures frequency signals and generates square wave signalFunction:

9U-6958 Module - Magneto Peak Detect

- Used to check magneto performance during actual operating conditions- When used with 146-4080 Digital Multimeter, user can measure magneto output DC Voltage- Provides separate voltage output for oscilloscope viewing of firing pulse train- Does not require power to operate

Checks magneto performance during actual operating conditionsFunction:

9U-7400 Multitach II Gp.

- Easy to use photo pickup for fast RPM measurement- Two digital displays show Input 1 and Input 2 values simultaneously- Backlit display for low light conditions - Rechargable batteries- Accepts many different types of pickups (Including some Multitach I pickups)- For more information see NEHS0605 Tool Operating Manual & NEHP5596 Brochure

Measures engine RPM, frequency, and engine set pointFunction:

9U-7401 Multitach II


Used to measures engine RPM, frequency, and engine set pointFunction:

9U-7402 Multitach II Photo Gp.


Used to measures engine RPM, frequency, and engine set pointFunction:

9U-7500 Transmission Analyzer

- Easy to read menus, on backlit LCD dislay step you through sequence of operation- Performs: Solenoid Condition Check, Transmission Shifts of all gears, & Shift Lever test- Flash memory allows internal software to be upgraded. Subscription NETG5021- For more information, see NEHP5617 Brochure & NEHS0644 Tool Operating Manual- CE Compliant

Shift Electronic Transmissions during testing on Test BenchFunction:



156-1060 Analyzer Gp. - Emission

- Used for fast and easy set-up and servicing of lean burn and stoichometric engines- Measures exhaust concentrations of O2, CO2, NO, and NO2- Built in thermal printer and Automatic water dump - For use on Gas Engines Only - CE Compliant- For more information, see PELJ0020 IRM & NEHS0713 Tool Manual

Used to setup, service, and monitor natural gas engine emissionsFunction:

156-1070 Analyzer Gp. - Emission

- Used for fast and easy set-up and servicing of lean burn and stoichometric engines- Measures exhaust concentrations of O2, CO2, NO, NO2, and CxHx- Measures exhaust and ambient temperatures, stack draft, and smoke test- Built in thermal printer and Automatic water dump - CE Compliant- For more information, see PELJ0020 IRM & NEHS0713 Tool Manual

Used to set-up, service, & monitor natural gas & diesel engine emissionsFunction:

170-8500 Particle Analyzer

- Provides instant feedback on effectiveness of filtration, abnormal wear conditions, and overall system cleanliness- Allows real-time testing of repaired units- Touchscreen Interaction - Internal Battery- CE Compliant

Used to analyze particle contamination on pressurized and non-pressurized systems

Function:

188-0645 Portable S2 Particle Analyzer

- Provides instant feedback on effectiveness of filtration, abnormal wear conditions, and overall system cleanliness- Allows real-time testing of repaired units- For more information, see NEHS0777 Instruction Manual & PELJ0050 IRM- CE Compliant

Used to analyze particle contamination on pressurized and non-pressurized systems

Function:

146-4080 Multimeter Gp. - Digital (RS-232)

- True RMS Digital Multimeter - Full Function Digital Measurements- Can be used with DataView to log any type of electrical signal (Requires 146-8488 Cable)- Provides 10th channel input for DataView- CE Compliant- For more information, see JEDG6000 Brochure & NEHS0554

Measures voltage, current, resistance, duty cycle, temp, & moreFunction:

6V-7070 Digital Multimeter

- Easy to use- Very Durable- CE Compliant

General purpose multimeter for measuring current, voltage, & resistanceFunction:



9U-7330 Multimeter - Fluke 87

- True RMS Digital Multimeter- Measures: ACV, DCV, Amp, Hz, Duty Cycle, Diode, Temp, & Impedence- CE Compliant

Used to test and adjust electronic circuitsFunction:

142-5055 Insulation Tester Gp.

- Used to measure and check insulation resistance for electrical power generation- Analog scale reads up to 10 GW for high insulation resistance readings- Meter ranges from 100 kW digital & 10 MW analog to test for faults on motors & generators- Tool defaults to voltmeter operation whenever an external voltage greater thant 25 VAC/DC- Replaces 9U-6003 Insulation Tester

Measures & checks insulation resistance for electrical power generationFunction:

152-7213 Scopemeter (123-120 VAC)

- Dual channel digital scope and dual channel true-RMS DMM- Brilliant high contrast backlit LCD with hardened scratch-resistant lens- AUTO key for fast, rock stable waveform displays of signals down to 1 Hz- Frequency range: 20 Hz at input - CE Compliant- For more information, see NEDG6011 Brochure

A

B

COM

A

B

F1

F2

F3

F4

V Hz A

V Hz A

mV

V

mV

V

s TIME ns

AUTO

SCOPEMENU

HOLDRUN

USEROPTIONS SAVEPRINT

C66974T1

Used to test and adjust electronic circuitsFunction:

163-0096 Process Calibrator

- Calibrates thermocouples, RTD's, voltage, resistance, Hz, Ma - CE Compliant- Stores up to 8,000 readings - Multilingual operation- Products requiring us of calibrator: 3600 Engine Protection Systems, Marine Monitoring Systems, 3600 Engine Management Systems, 3600 Custom Program Logic Control- For more information, see PELJ0023

Used to source and calibrate temperature and electrical signalsFunction:

4C-5521 Phase Sequence Meter

- Provides positive identificaion of phase sequence of energized 3 phase 40-60 Hz power lines from 100 to 600 Volts- Gives user inidication that all phases have continuity or will indicate phase that has fault- Has heavily insulated fused leads for users protection- Enhanced durability because there are no moving parts

Identifies phase sequence of energized 3-phase power linesFunction:

9U-5222 Voltage Detector - AC

- Safe, quick, and easy way to locate energized circuits- Good tool choice when looking for open fuses or circuit breakers or even broken wires- Both audio and visual indicators- For more information, see NEHS0564 Tool Operating Manual

Used to locate energized circuitsFunction:



155-5175 AC Current Probe

- Measure up to 1000 Amps AC with standard Digital Multimeter- Used with 6V-7070, 9U-7330, or 146-4080 Digital Multimeter- Replaces 6V-4960 AC Current Probe- CE Compliant

Used to measure AC currentFunction:

155-5176 AC/DC Current Probe

- Measure up to 1000 Amps AC/DC with standard Digital Multimeter- Used with 6v-7070, 9U-7330, or 146-4080 Digital Multimeter- Replaces 9U-5795 AC/DC Current Clamp- CE Compliant

Used to measure AC & DC currentFunction:

6V-9130 Temp Adapter Gp.

- Used with 9U-7330 or 6V-7070 Digital Multimeter Groups- Kit converts Included Type K Thermocouple to mV readable by standard Multimeters- CE Compliant- For more information, see SEHS8382

Used to measure oil, coolant or air temperatures (-50°C to 900°C)Function:

8T-0900 Ammeter - AC/DC Clamp-On

- Measure AC/DC Current up to 1200 Amps- Digital Readout on handle- Used with 6V-7070, 9U-7330, & 146-4080 Digital Multimeters

Measures AC & DC current in cables without breaking circuit (0-1200A)Function:

1U-8115 Test Lead Set - Insulated Tip

- Used with 9U-7330, 6V-7070, & 146-4080 Digital Multimeter Gp.

Test lead probes with spring loaded insulatorsFunction:

6V-7072 Test Lead Set

- Deluxe Test Lead Kit for all Meters- Includes Alligator Clips, Test Leads, & Banana Leads- For use with 6V-7070, 9U-7330, & 146-4080 Digital Multimeters- CE Compliant

Test Lead Kit for use with Digital MultimetersFunction:



7X-1710 Probe Gp.

- Allows user to measure electrical signal from connector without separating connector- Used with 6V-7070, 9U-7330, & 146-4080 Digital Multimeter Gp.

Used to measure voltages without disconnecting wiring harnessFunction:

164-3310 Infrared Thermometer

- Full Featured Infrared Thermometer -32 - 900 C (-25 - 1600 F)- Bar Graph Display- Laser Circle Shows Size of Area being Measured- CE Compliant- For more information, see NEHP6016 Datasheet

Measures surface temperature without contact (battery powered)Function:


- Full Featured Infrared Thermometer r -32 - 900 C (-25 - 1600 F)- Log Up to 100 Readings- PC Data Graphing Software- 110V Charger - CE Compliant- For more information, see NEHP6016 Datasheet

Measures surface temperature without contact (110 VAC or battery)Function:


- Full Featured Infrared Thermometer -32 - 900 C (-25 - 1600 F)- Log Up to 100 Readings- PC Data Graphing Software- 220V Charger - CE Compliant- For more information, see NEHP6016 Datasheet

Measures surface temperature without contact (220 VAC or battery)Function:


- Small compact size -32 - 400 C (-25 - 750 F)- Accuracy of +/- 1% of Reading- For more information, see NEHP6016 Datasheet- CE Compliant- Replaces 148-2388 Infrared Thermometer

Measures surface temperature without contacting surfaceFunction:


- Small compact size -32 - 600 C (-25 - 1100 F)- Calculates max, min, & average temperatures- For more information, see NEHP6016 Datasheet- CE compliant- Replaces 148-2400 Infrared Temperature Tool

Measures surface temperatures without contacting surfaceFunction:




- Low Cost Infrared Thermometer- -20 to 260 C (0 to 500 F) Temperature Measurement Range- Circle Laser- CE Compliant

Non-Contact Temperature MeasurementFunction:

4C-6090 Multichannel Temp Selector

- Measures 16 temperatures individually- Allows serviceman to read individual cylinder exhaust temperatures to locate faulty injector- Used with 6V-7070 & 9U-7330 Multimeters with 6V-9129 Temperature Adapter- OR Used with 146-4080 Multimter with type K Measurement capability- For more information, see NEHS0537 Special Instruction

Measures up to sixteen temperatures individuallyFunction:

4C-6500 Digital Thermometer Gp.

- Fast and accurate method of measuring temperature- Backlit, digital LCD Display for use in low light conditions- Large Display for easier viewing- Provides user with differential temperature measurement between 2 and 5 channels- For more information, see NEHS0554

Used to measure and record temperaturesFunction:

8T-2844 Recorder Gp.

- Used for checking operating temperatures of the cooling, engine oil, hydraulic, & brake systems- Quick, easy, inexpensive method to determine component's surface temperature- 6 silver colored temperature sensitive indicator windows on each recorder- 5 different temperature recorders for 5 different ranges

Measures highest surface temperature of engine componentsFunction:

146-1738 Borescope - Precision (12")

- 305mm (1ft) shaft, 6.53mm (.25 inches) diameter- Includes 90 degree mirror tube for right angle viewing- Adjustable focus- Portable battery light source- For more information see NEHS0504 Tool Opeating Manual & PELJ0046 IRM

Used to make visual inspection of internal surfacesFunction:

8T-9290 Borescope - Battery Operated

- Fits into bores as small as 8mm (.32") and reach 240mm (9.5 inches)- Battery handle can be remotely coupled to scope using extension cable (supplied)- For more information see NEHS0504 Tool Operating Manual & PELJ0046 IRM




1U-5268 Borescope

- 580 mm (23 in) Length, 6.5 mm (.25 in) Diameter- Allow straight viewing of internal surfaces- Used with Light Source 1U-56266(110 VAC) 190-8160 (220V) & 1U-5265 (Battery)- For more information see NEHS0504 Tool Opeating Manual & PELJ0046 IRM


9U-6940 Borescope - Right-angle View

- 6.50mm (.256 inches) probe diameter, 570mm (22.5 inches) working length- Housing eliminates surface mirror scratching problem - 60 Degree Field Of View- Fits through nozzle hole on engines using a "pencil style" injector- Used with Light Source 1U-56266(110 VAC) 190-8160 (220V) & 1U-5265 (Battery)- For more information see NEHS0504 Tool Opeating Manual & PELJ0046 IRM

Used to inspect internal openings and passagesFunction:

186-0170 Flexible Shaft Borescope

- 6mm (.256 inches) probe diameter, 600mm (24 inches) working length- The flexible portion of the borescope is waterproof and resistant to 60 deg. C (140 deg. F)- For more information see NEHS0504 Tool Opeating Manual & PELJ0046 IRM- Used with Light Source 1U-56266(110 VAC) 190-8160 (220V) & 1U-5265 (Battery)


186-0180 Borescope - Rigid Tube

- 14mm (.551 inches) probe diameter, 940mm (37 inches) working length- 140 degree adjustable direction of view with 45 degree field of view- Sealed tip to prevent contamination from oil or fuel- Used with Light Source 1U-56266(110 VAC) 190-8160 (220V) & 1U-5265 (Battery)- For more information see NEHS0504 Tool Opeating Manual & PELJ0046 IRM


1U-5266 Light Source (110 VAC)

- Compact, lightweight- Uses 150 watt light bulb, light intensity is adjustabl- Inlcudes a fan to prevent overheating - Bulb is protected with a 2 amp fuse- Alternative Tool: 190-8160 Light Source (220 VAC)- Used with 1U-5268, 9U-6940, 186-0170, and 186-0180 Borescopes

Provide illumination for borescopesFunction:

190-8160 Light Source

- Uses 150 watt light bulb, light intensity is adjustable - Compact, lightweight - Inlcudes a fan to prevent overheating - Bulb is protected with a 2 amp fuse- Alternative Tool: 1U-5266 Light Source (110 VAC)- Used with 1U-5268, 9U-6940, 186-0170, and 186-0180 Borescopes- For more information see, NEHS0504 Operation Manual & PELJ0046 IRM

Provide illumination for borescopesFunction:



1U-5265 Battery Operated Light Source

- Used with 1U-5268, 9U-6940, 186-0170, & 186-0180 Caterpillar Borescopes- 110 V Rechargabel Light Source for Caterpillar Borescopes- For more information, see NEHS0504 & PELJ0046 IRM

Portable Light Source for Field UseFunction:

1U-5470 Engine Pressure Gp.

- Checks pressures on turbocharged diesel and natural gas engines

Checks pressures on turbocharged diesel and natural gas enginesFunction:

5P-8558 Calibrating Gp. - Pressure Gauge

- 3 Gauges of 0.5% accuracy with pressure ranges of 1100 kPa (160 PSI), 4150 kPa (600 PSI) and 34,500 kPa (5000 PSI)- Two lower pressure gauges protected from excessive pressure by two sensor valves- A separate source of pressure is required to actuate the calibrating group

Used to check or calibrate pressure gaugesFunction:

6V-7830 Tetragauge

- Functions as general purpose pressure measurement device- Capable of measuring hydraulic or air pressure - Range -100 kPa (-14.5 psi) to 40,000 kPa (+5800 psi).- 8T-5324 Repair Kit available to service this device

General purpose device for measuring hydraulic or air pressureFunction:

1U-7318 Continuity Tester / Flashlight

- Allows user to test continuity- Can be used as flashlight- High impact plastic- Magnet allows hands free use

Used as a flashlight or continuity testerFunction:

5P-7277 Tester - Voltage

- Used to make quick checks for presence of voltage- Indespensable for checking out circuits, relays, bulbs, wires, & switches- Designed for voltage range from 12 to 36 Volts- Bulb lights brightly when connected to 36 Volts and dims progressivly with lower voltages- Uses standard 8D-1429 Bulb

Used to make quick checks for presence of voltageFunction:



8T-0500 Light - Continuity Testing

- Used to test non-energized circuits; lamp comes on brightly when connected across low resistance circuit- Designed for rugged field use- Comes with light bulb (6V-3061) and 2 N Size batteries (4c-8363)- Replaces canceled 8S-4627 Circuit Continuity Tester

Used to test for non-energized or open circuitsFunction:

177-2330 Digital Battery Analyzer

- Automatically Tests 6V & 12V Batteries - CE Compliant- Analyzer Checks for State-of-Charge, Condition, and Voltage- Batteries are Tested in the Machine - No Need to Remove- Temperature compensating circuit for cold batteries- For more information, see PELJ0037 IRM & NEHP6014 Datasheet

Used to evaluate the condition of 6 & 12 volt batteriesFunction:

4C-4911 Battery Load Tester

- Two, easy to read LCD Displays show accurate measurements of Voltage & Current- Voltage measured to one hundredth of a volt for accurate readings- Heavy-Duty carbon pile, leads, and clamps - 1000 Amp Load Capacity- Fan cooled, internal fan turns on when load is applied - For more information, see NEHS7633 Special Instruction

Heavy Duty Battery Tester used to test 6, 8, & 12 volt batteriesFunction:

4C-6600 Battery Voltmeter

- Designed to quickly determine voltage state of battery 6 - 60 Volts DC- Easier and faster than using a hydrometer to measure specific gravity- Battery voltage is displayed on a bright, red LED display

Measures battery voltage to determine state of chargeFunction:

1U-7297 Coolant and Battery Tester

- Temperature Comensated- Can be used on either hot or cold radiators- Can also accurately check some types of permanent antifreeze, such as Dowtherm 209- Alternative Tool: 1U-7298 Coolant and Battery Tester (degrees C)

Checks coolant freezing point and battery charge condition (degrees F)Function:

1U-7298 Coolant and Battery Tester

- Temperature Comensated- Can be used on either hot or cold radiators- Can also accurately check some types of permanent antifreeze, such as Dowtherm 209- Alternative Tool: 1U-7297 Coolant and Battery Tester (degrees F)

Checks coolant freezing point and battery charge condition (degrees C)Function:



121-9588 Removal Tool (16 Gauge TXL)

- Replaces 121-9587 Removal Tool- For more information, see SEHS9615 Special Instruction

Removes wires from 40 & 70 pin connectorsFunction:

151-6320 Removal Tool (SXL/GXL)

- For more information, see SEHS9615 Special Instruction

Removes pins and sockets from Deutsch & AMP connectorsFunction:

175-3700 DT Connector Service Kit

- Used to maintain and repair Deutsch DT style connectors (Square & Rectangle) on electronic engine harnesses- For more information, see SEHS9615 Special Instruction

Used to service and repair Deutsch "DT" type connectorsFunction:

190-8900 HD Connector - Field Service Kit

- Used to maintain and repair Deutsch HD style connectors (Round) on electronic engine harnesses- For more information, see SEHS9615 Special Instruction

Used to service Deutsch HD type connectorsFunction:

124-5643 3-Pin Packard Break-Out Cable

- Provides voltage test points for individual wires in electronic engine control systems- Used on 3119 HEUI in GM Highway Trucks- Used with 146-4080, 6V-7070, & 9U-7330 Digital Multimeters

Provides test points for individual wires in wiring harnessFunction:

125-3662 Cable - Sensor Bypass

- HEUI bypass cable used to isolate & test sensors for faults

Used to isolate and test sensors for faultsFunction:



127-6359 Cable As. - Adapter HEUI Injector

- Used to test injector and/or injectory harness- Allows wiring to an individual injector to be bypassed- Helps to isolate problem between injector or harness

Used to test injector and/or injector harnessFunction:

129-2018 Cable As. - Power

- Allows power & communication to an ADEM II ECM when vehicle voltage is unavailable

Provides access to data link from 40-pin ECM and powers service toolsFunction:

134-5195 Cable As. - Adapter (40 pin)

- 40 pin square C/D to A/B adapter cable.- Allows connection of 7X-171 Square A/B 40 pin to 3500 & 3600 engines

Adapts 7X-1715 Cable Assembly to a 40-pin CD-keyed connectorFunction:

139-4166 (CAT/ATA) Universal Cable

- Used to connect either the ATA Data-link or the Cat (CDL) Data-link to the 7X-1700 CA I- Replaces cancelled 7X-1412 Cable Assembly and 7X-1570 Cable Assembly- Can be used with 171-4400 Communications Adapter II for ATA & CDL only

Connects ATA data-link or the CAT (CDL) data-link to 7X-1700 Comm Adapter

Function:

140-2266 Cable As. - 70 Pin

- Used to provide test points for individual wires in engine wiring harness- Harness has standard probe tips which allow technician to check signal- Used to test signal on limited circuits

Provides wire test points for electronic engine control system (ECM)Function:

143-4508 Cable - Timing (G3408C)

- Allows user to check engine timing via timing light & flywheel marks on G3408C Gas Engine- Allows check of primary signal going to each transformer- Cable installs between ignition wiring harness and valve cover connector- Used with 146-4080 or 9U-730 Digital Multimeter

Used to check ignition timingFunction:



143-4509 Cable - Timing (G3412C)

- Allows user to check engine timing via timing light & flywheel marks on G3412C Gas Engine- Allows check of primary signal going to each transformer- Cable installs between ignition wiring harness and valve cover connector- Used with 146-4080 or 9U-730 Digital Multimeter

Used to check ignition timingFunction:

157-4829 Cable As. - Adapter

- Connects 139-4166 Diagnostic Cable to J1939 under-dash diagnostic connector- 9 Pin to J1939 Adapter Cable

Under dash conversion harness for FreightlinerFunction:

163-5443 Harness - Detonation Sensor

- Allow user to determine condition of detonation sensor on 3400, 3500, & 3600 Gas Engines- For more information, see Page 13, May 1999 Engine News, "Testing Detonation Sensor For Proper Use"- Used with 146-4080, 9U-7330, or 6V-7070 Digital Multimeter

Used to measure condition of detonation sensorFunction:

167-9225 Harness As.

- Attaches to the ADEM 2000 Engine harness connector or auxillary battery to service machine without power- Same as 129-2018, except for use with ADEM III- Required to bench flash the ADEM III ECM

Provides access during cranking to ECM with 70-pin Data LinkFunction:

196-0055 Cable - Serial

- Serial PC Cable connects 171-4400 Communications Adapter II to PC 7.62 m (25 ft)- Part of 171-4400 Comm Adapter II Group

Connects Communication Adapter II to PCFunction:

1U-9710 Adapter Cable

- Used with 6V-2100 Multitach, 6V-3121 Multitach Group, 9U-7400 Multitach Group, and 6V-9060 Spark Timing Adapter Group

Used with Mulitach to measure engine RPMFunction:



207-6845 Communications Adapter Cable

- Short Data Link Cable 51 cm (20 in)- Use with ATA, CDL, & J1939-1- Part of 171-4400 Communications Adapter II Group- Works with cancelled 7X-1700 & 171-4400 Communications Adapters- Replaces cancelled 160-0133 Cable

Connects communications adapter to engineFunction:

208-0059 Cable Assembly

- Used to provide test point for all individual wires in Engine wiring harness of ADEM III- Connects between ECM and main wiring harness- Allow testing access to all 70 wires

70 Pin Breakout T Cable AssemblyFunction:

7X-1395 Adapter - SI TDC

- 2 Pin Deutsch DT TDC Calibration Cable- Used with 7X-1695 cable to allow connection to TDC adapter for S. I. Engines

Allows 7X-1695 Cable to be used on industrial and gas enginesFunction:

7X-1425 RS-232 Cable

- Used to connect cancelled 7X-1700 Communications Adapter I to RS-232 Port on PC

Connects 7X-1701 Communications Adapter to RS-232 computer portFunction:

7X-1686 Adapter Cable

- ATA in-cab adapter from 139-4166 (9 Pin) to under-dash 6 Pin connection

Adapts on-highway truck 6 pin connector to 9 pin com adapter cableFunction:

7X-1688 Cable Gp.

- Cable connects 7X-1700 Communicaitons Adapter I to RS-232 - Item #2

T-adapter for ECAP and DDTFunction:



7X-1695 Cable - TDC

- Used on captive engine applications- Allows magnetic sensor to be connected to engine to input timing information to ECM- Used with 7X-1395 cable to allow connection to TDC adapter for S. I. Engines- Used with 8T-8697 ECAP & 7X-1400 DDT

Allows magnetic timing sensor to be connected to engine ECMFunction:

7X-1714 Cable - 3116 Engine Adapter

- Cable used to connect 139-4166 Communication Adapter harness to under-dash Packard connector- Used with 7X-1700 Communications Adapter I & 171-4400 Communications Adapter II Gp.

Adapts under dash Packard Connector to communications adapterFunction:

7X-1715 Cable As. - Small (40 Pin)

- Square 40 pin A/B Breakout Cable allowing voltage checks on any wire or between wires- Makes troubleshooting of electronic engine control systems faster & easier- Use with 146-4080, 9U-7330, or 6V-7070 Digital Multimeters

Provides tests points for individual wires in wiring harnessFunction:

7X-6370 Adapter Cable As. - 3 Pin DT

- Used to service 3406 PEEC and 3176 engines- Provide test points for individual wires in wiring harness- Used with 146-4080, 9U-7330, & 6V-7070 Digital Multimeters

Provides test points for wiring harness to faciliate troubleshootingFunction:

8T-8694 Adapter Cable As. - 5 Pin

- Used for servicing 3406 PEEC & 3176 Engines- Allows user to troubleshoot engine control system by providing test points- 5 Pin Breakout Adapter Cable Assembly- For use with 8T-8697 ECAP










9X-0248 Adapter Cable As. - Transducer

- Used when servicing 3176 Engines- Allows user to perform electrical measurements on electronic engine controls- For use with 8T-8697 ECAP


9X-1160 Adapter Cable As. - 40 Pin

- 40 Pin Breakout Adapter Cable for use on 3176 Engines


6V-2012 Gauge Gp. - Micrometer Depth

- Inch Measurement- Contains complete set of measuring rods from 0-228.8 mm (0-9 in) stored in wooded case- Base is 76.2 mm (3 in) wide and uses 3.96 mm (5/32 in) rods.

Measures depths up to 230 mm (inch scale)Function:

6V-2034 Adapter

- Used with the 6V-7059 Multiple Anvil Micrometer

Used to measure engine valve lip thicknessFunction:

6V-6042 Point Gp.

- For use with 8T-1000 Electronic Position Indicator & 6V-7926 Dial Indicator- Has plastic box with divided tool holder, space to cut more slots for storage of extra points - Part numbers and sizes are shown on a chart inside the lid of the box.- Will fit all dial indicators with 4-48 thread

Contact points for the dial indicators (2.18 to 120.5 mm long)Function:



6V-7030 Gauge Gp. - Micrometer Depth

- Millimeter Measurement- Contains complete set of measuring rods from 0-228.8 mm (0-9 in) stored in wooded case- Base is 76.2 mm (3 in) wide and uses 3.96 mm (5/32 in) rods.

Used to measure depths up to 230 mm (metric scale)Function:

6V-7059 Multiple Anvil Micrometer

- Micrometer used for measuring top flange thickness on cylinder liners- Used with 6V-2034 Adapter to measure valve lip thickness

Measures cylinder liner top flange thickness and valve lip thicknessFunction:

6V-7926 Dial Indicator Gp.

- Use primarily for measuring off-engine timing dimensions when setting fuel pump lifters- Measurements are made with 25.4 mm (1 in) travel indicator and 5 contact points- Can also be used for accurate depth measurements up to 127 mm (5 in)

Used to measure off-engine timing and other depth measurementsFunction:

8T-0450 Thread Identification Kit

- Available to help determine thread size- The size of internal port threads, external adapter threads, and bolt threads can be measured with the tools in this kit- Works on Metric, BSP, and US Standard Threads

Used to determine thread sizesFunction:

6V-2196 Microscope

- 20X microscope is recommended for checking crankshaft bearing surfaces- Accurate measurement is provided by a scale reading in 0.1mm increments- Used with 6V-6059 Microlite

Pocket 20X microscope for general inspectionFunction:

6V-6059 Microlite

- Penlight used with 6V-2196 20X General Usage Microscope- Includes 6V-3061 Bulb- Requires 1U-9535 AAA Batteries (2)

Provides a light source for the inspection microscopeFunction:



198-4240 Digital Pressure Indicator

- Quickly & easily determine system pressures, vacuum, differential pressure, & temperature- Easily locate pressure spikes with Min/Max function - Resolution to 1 psi/bar- Greater accuracy than standard handheld gauges - Recalibrates sensor with each use- CE Compliant- For more information, see PELJ0060 IRM, NEHP6021 Datasheet, & NEHS0818 Manual

Measures Pressure, Vacuum, Differential Pressure, & TemperatureFunction:

6V-9060 Adapter Gp. - Spark Timing

- Used with 8T-5300 Timing Indicator required for 3304, 3306, & 3516 Engines

Checks dynamic timing on gas enginesFunction:

8T-5300 Indicator Gp. - Timing

- Used to measure fuel injection timing for diesel engines- Checks operation of auto timing advance on euipped engines- Requires 8T-5301 Diesel Timing Adapter or 6V-9060 Spark Timing Adapter- Replaces 6V-3100 Timing Indicator Gp.

Used to measure fuel injection timingFunction:

8T-5301 Adapter Gp. - Diesel Timing

- Required for 300, 1100, 3200, 3300, & 3400 Series Engines- Used with 8T-5300 Timing Indicator Gp.

Used to measure fuel injection timing on diesel enginesFunction:

131-5050 DataView Gp.

- Has data logging capabilities - Works on ALL Caterpillar machines, new & old- Uses standard Cat sensors and replaces 15+ green sensor boxes- For more information, see NEHS0662 Tool Operating Manual & NEHP6016 Datasheet- Measures and records information from sensors installed on machine or engine- CE Compliant - Does not include PC or sensors

PC based diagnostic tool that measures and records engine parametersFunction:

131-5051 DataView TechStation Gp.

- Has data logging capabilities - CE Compliant- Uses standard Cat sensors and replaces 15+ green sensor boxes- Measures and records information from sensors installed on machines and engines- Includes all accessories needed to operate DataView on a PC except sensors- For more information, see NEHS0662 Tool Operating Manual & NEHP6016 Datasheet

PC based diagnostic tool that measures and records engine parametersFunction:



154-8101 Fuel Flowmeter Gp.

- Display not included- State-of-the-art gear-type flowmeters with temperature compensation- +/- 0.5% accuracy per flowmeter - Prevents starvation if plugged- For more information, see PELJ0021 IRM & NEHS0697 & NEHS0698 Tool Operating Manual-Additional Components: 1U-5306 Hose Gp, 8T-9820 Power Spply, 5P-7366 Power Cable

Measures diesel engine fuel burn rate on 3408/12E, 3500Function:

154-8102 Fuel Flow Measurement System

- Display included - Prevents starvation if plugged- State-of-the-art gear-type flowmeters with temperature compensation- +/- 0.5% accuracy per flowmeter- Used with 154-8106 Fuel Flow Display- For more information, see PELJ0021 IRM & NEHS0697 & NEHS0698 Tool Operating Manual

Measures diesel engine fuel burn rate on 3408/12E, 3500Function:

168-7730 Fuel Flowmeter Gp.

- +/- 0.5% accuracy per flowmeter- Prevents starvation if plugged- 3612 & 3616 engines require accumulators- Used with the 8T-9300 Fuel Flow Monitor, 9U-7400 Multitach, or 131-5051 DataView- For more information, see PELJ0033 IRM & NEHS0740/NEHS0741 Tool Operating Manual

Measures diesel engine fuel burn rate on 3600Function:

168-7740 Fuel Flow Measurement System

- Inlcudes 154-8106 Fuel Flow Display- +/- 0.5% accuracy per flowmeter - Prevents starvation if plugged- 3612 & 3616 engines require accumulators- For more information, see PELJ0033 IRM & NEHS0740/NEHS0741 Tool Operating Manual

Measures diesel engine fuel burn rate on 3606, 3608, 3612, & 3616Function:

179-0710 Burn Rate Meter (With Display)

- Includes 154-8106 Fuel Flow Display- Flowmeter burn rate: 4 LHP (1.05 GPH) to 260 LPH (69 GPH)- Flowmeter Accuracy: +/- 1% of reading, +/- 0.1 GPH- Flowmeter type: Positive displacement, piston. Temperature compensated & output scaling- For more information, see PELJ0042 IRM & NEHS0776

Used to measure engine burn rate on 3116, 3126, C-9, 3208, 3304, 3406/08Function:

179-0711 Burn Rate Meter (No Display)

- Does not Include 154-8106 Fuel Flow Display- Flowmeter burn rate: 4 LHP (1.05 GPH) to 260 LPH (69 GPH)- Flowmeter Accuracy: +/- 1% of reading, +/- 0.1 GPH- Flowmeter type: Positive displacement, piston. Temperature compensated & output scaling- For more information, see PELJ0042 IRM & NEHS0776

Used to measure engine burn rate on 3116, 3126, 3176, 3208, 3304, 3406/08

Function:



143-4062 Sensor - Pressure (100 psi)

- 0 to 689 kPa (0 to 100 psi)- Used with 131-5050 or 131-5051 DataView Gp.- For more information, see NELG5023 Sensor List- Low cost

Pressure sensor for use with DataViewFunction:


- 0 to 6890 kPa (0 to 1000 psi)- Low cost- Used with 131-5050 or 131-5051 DataView Gp.- For more information, see NELG5023 Sensor List



- 0 to 51675 kPa (0 to 7500 psi)- Low cost- Used with 131-5050 or 131-5051 DataView Gp.- For more information, see NELG5023 Sensor List


153-9630 Test Gp. - Sensor

- Kit Includes: 153-9625 PWM Sensor Adapter - CE Compliant 153-9626 Break-Out Cable-HD 153-9627 Break-Out Cable-DT- Allows user to T into existing Cat sensors for measure and record using DataView- For more information, see NELG5023 Sensor List & PELJ0009 IRM

Used to test CAT ® PWM and analog sensorsFunction:

1U-9139 Universal Fuel Line Pickup

- Item #1- Used with 6V-2100 Multitach, 131-5050 or 131-5051 Dataview Gp.

Used with multitach or DataView to measure engine speedFunction:

6V-4950 Pickup Gp. - Injection Line Speed

- Mounts to fuel line to measuer fuel pulses to determine RPM- Works on Perkins fuel lines as well as those with remote unit pump group- Works on precombustion chamber fuel systems & on some smaller direct injection systems- Used with 9U-7400 Multitach II & 131-5050 DataView- For more information, see SEHS8029 Special Instruction

Used with multitach to measure diesel engine speedFunction:



8T-5184 Transducer - 1/4" Dia x 3.5"

- Used with 8T-5300 Timing Indicator Group- Shorter (0.5") than the 6V-2197 transducer- [8.9 cm (3.5 in) long

Fuel line pressure transducerFunction:

8T-5185 Transducer - 1/4" Dia.x 7"

- Used with 8T-5300 Timing Indicator Group- Longer (2.5") than the 6V-2197 transducer- 17.8 cm (7 in) long

Fuel line pressure transducerFunction:

1P-3537 Dial Bore Gauge Gp. (Inch)

- Useful for making critical bore measurement from 50.8 mm (2 in) to 203.2 mm (8 in)- Used to reconditioning cylinder bores on 1100 & 3100 series engines- Used to refinish connecting rods in 137.16 mm (5.4 in) bore V8 & V12 engines- Item #2- See T&SPG (NENG2500) for other available models

Used to measure bore diameters (50.8 to 203.2 mm dia.)Function:

5P-2170 Dial Bore Gauge Gp.

- This gauge and its related masters provides accuracy to.0025 mm (.0001 inch) for measuring all bores in the size range 19.05-38.10 mm (.750 inch to 1.500 inch).- Particularly useful for measuring the relief valve spool bores in pressure control bodies on 631, 633, 637, 641,650, 651, 657, 660, and 666 Tractors with eight speed transmissions.- See T&SPG (NENG2500) for other available models

Used to measure bore diameters (19.05 to 38.10 mm)Function:

6V-6000 Dial Bore Gauge (metric)

- Item #2; Used with 6V-6030 Size Setting Fixture (Item #1- See T&SPG (NENG2500) for other available models

Used to measure bore diameters (30.0 to 50.8 mm)Function:

6V-6030 Size Setting Fixture

- A precision measuring instrument with a diameter range of 30 - 50.8 mm (1.2 - 2 in) graduated to 0.002 mm (.00008 in) increments- Item #1- Used with 6V-6000 Dial Bore Gauge (Item #2)- For more information, see SMHS8036 Special Instruction

Used to calibrate or check dial bore gauges (30.0 to 50.8 mm)Function:



6V-7897 Dial Indicator

- Dial Indicator used to convert 1P-3535 Dial Bore Gauge to the 6V-7898 Dial Bore Gauge- Used with 1P-3535 Dial Bore Gauge

Converts dial bore gauge to metricFunction:

6V-7898 Dial Bore Gauge - Metric

- The dial bore gauge and size setting fixture will measure all internal diameters from 1.97 inch to 7.87 inch (50 to200 mm) and depths from 0.51 inch to 11.81 inch (13 to 300 mm) in increments of 0.00008 inch (0.002 mm).- Used with 6V-7899 Size Setting Fixture- See T&SPG (NENG2500) for other available models

Measures internal diameters (50 to 200 mm) & depths (13 to 300 mm)Function:

6V-7899 Size Setting Fixture - Metric

- Used with 6V7898 Dial Bore Gauge- For more information, see SMHS8254 Special Instruction

Used to check or calibrate the dial bore gaugesFunction:

123-6471 M300 Diagnostic Tool Group

- Tester will display readings from both engine control and pump control systems- This hand-held tool features a 4 line, 16 character liquid crystal display (LCD)- For more information, see SEHS9825 Special Instructions, SENR6261 Test & Adjust Manual

Used to setup, test, calibrate, & troubleshoot M300 Series Wheeled Excavators

Function:

125-2580 Tool Gp. - HEUI Engine

- HEUI Diagnostic Tooling - Includes all necessary cables, harnesses, & pin removal tools- Injector and IAPC valve removal & installation tools- Modified injector clamp to aid in proper assembly and tightening of jumper tube- Necessary bit drivers and socket to work on hard-to-reach components- New double ended offset feeler gauge for setting valves

Troubleshoots electrical and hydraulic systemsFunction:

148-9610 Mobile Diagnostic PC Cart

- Durable painted steel with fiberglass top - Storage for up to 30 CDs in the door- PC installs inside with cooling fan - Internal power stripes provided- For more information, see NEDG6001 Datasheet & PELJ0013 IRM- CE Compliant- 150-8756 is 220V alternative cart

Used to hold PC, monitor, printer and DataView hardwareFunction:



8C-9801 Signal Adapter Gp. - PWM

- Provides additional function to measure frequency and duty cycle of PWM signals- Allows user to verify or diagnose operation of some sensors on electronic engines- Used with 8T-8697 Analyzer Programmer (ECAP)

Measures frequency and duty cycle of pulse width modulated signalFunction:

8S-2257 Eye Loupe

- 12 X Power- 25.4 mm (1 in) Depth- Extremely Portable

Eye loupe with 12X powerFunction:

9U-6695 Indicator - Spark Plug Firing

- Adjustable sensitivity - user can set firing indicator to flash when placed near primary wire on exposed coils of 6.25 inch bore engines- Reliable tool to diagnose ignition problems- Flashing LED indicator easily seen in daylight

Indicates spark plug firingFunction:

9U-7554 Printer Gp. - Portable (110 VAC)

- Standard RS-232 Portable Field Printer- Used with 8T-8697 ECAP

Used to make hard copy records of various diagnostic informationFunction:

9U-7560 Field Soldering Iron Gp.

- 12V Cigarette Connector Field Soldering Iron- Used with 4C-9024 Battery Pack Gp. or 12 volt source- In line fuse prevents damage and/or overload- For more information, see NEHS0601 Tool Operating Manual

Used to solder electrical connections (battery powered)Function:


herramientas de diagnostico caterpillar

Documents