hiradmat users meeting 29/5/2015 adrian fabich eucard-2 is co-funded by the partners and the...
DESCRIPTION
Feed-throughs Between TNC and TT61 Used already by GlassyC/dBM Inserts - viewing windows arrived at CERN to be installed early June 29/5/2015A. Fabich3 EDMS SPSLHRM_0060TRANSCRIPT
HiRadMat –Users Meeting
29/5/2015
Adrian Fabich
EuCARD-2 is co-funded by the partners and the European Commission under Capacities 7th Framework Programme, Grant Agreement 312453
A. Fabich 2
HiRadMat beam …
• GlassyC is installed
Waiting for beam …• Some pulses on 15. May• Now waiting for improvements of SPS extraction
29/5/2015
A. Fabich 3
Feed-throughsBetween TNC and TT61• Used already by GlassyC/dBM
Inserts - viewing windows• arrived at CERN• to be installed early June
29/5/2015
EDMS SPSLHRM_0060
A. Fabich 4
TT61 setup
• TT61 will be equipped with– A standard SPS 19” rack (600 mm x 800 mm)– A table
29/5/2015
A. Fabich 5
Cabling databaseDocument in finalization (EDMS 1415953)• Permanent cabling installed
– Connecting TNC and TJ7 (patch rack)– Connecting TJ7 and control room
Already installed, to be added to DB:– Connecting TNC and TT61– 5 x NE48 (TT61 connector to be exchanged)– 12 x CK50
29/5/2015
A. Fabich 6
Cabling overviewAn experimental TNC table is equipped with:
From Control Room– 6 x NE48
• 5 x can be used in manual mode• 1 x on automatic plug-in
– 24 x CK50 e.g. for BPM read-out– Several HV cables – manual mode, e g. for BPM supply
From TT61– 5 x NE48 from TT61
• 5 x on automatic plug-in• E.g. for strain gauges
– 12 x CK50• E.g. for high frequency signals (from BPM)
– Dedicated experimental cables (subject to discussion) via empty cable ducts• E.g. fibre optics• Max diameter 35 mm (also for connectors)• Beyond 35 mm requires dedicated study using 3rd feed-through with inner diameter 100 mm
29/5/2015
A. Fabich 7
Cable proposal forHRMT22 – Ptarg• 5 x NE48 from Control Room
– 2 x in auto-plug-in mode for horizontal stage• Merge to one NE48?
– 2 x in manual mode for vertical stage• Merge to one NE48?
– 1 x in auto-plug-in for LEDs• 2 x NE48 from TT61
– auto-plug-in for vacuum gauges/controls• 4 x CK50 from TT61
– For BPM• No fibres foreseen
This is a preliminary list to be completed by the system responsibles.
29/5/2015
A. Fabich 8
Cable proposal for HRMT24 – BeGrid
• 4 x NE48 from Control Room– 2 x in manual mode for vertical stage– 1 x in auto-plug-in for LEDs– 2 x in manual mode for For BPKG/BTV
• CK50 from Control Room– For BPKG/BTV
• 5 x NE48 from TT61 – In auto-plug-in for strain gauges
• Fibres required?
Such a list should be- Prepared by each experiment- Re-iterated with HRM coordination
29/5/2015
A. Fabich 9
Cable proposal for HRMT 27 - RodTarg
NE48 ? :• 1 x Thermocouple cable 24 pairs, Type K• 1 x Thermocouple cable 8 pairs, Type N• 1 x NE8 copper cable
Special cables – to be discussed:- Should be reduced to a minimum
- Space in feed-throughs is limited- Optimizing installation effort
• 2 x Radiation hard camera cables• 3 x Optic fibres respecting the standard G.652• 1 x LumaSense Pyrometer Optic fibre:
http://www.lumasenseinc.com/uploads/Products/Impac/pdf/Datasheets/Pyrometer/Series_740/IGA740_IGA740_LO_Datasheet.pdf
• 2 x PANDA PM Optic Fibers
29/5/2015
A. Fabich 10
Schedule
29/5/2015
Consider 1-2 additional weeks of back-up for beam slot
A. Fabich 11
Subsistence for travel/accommodationEuCARD-2 “Transnational Access”
29/5/2015
Do not hesitate sending requests to [email protected] info: https://espace.cern.ch/hiradmat-sps/Wiki%20Pages/[email protected]
A. Fabich 12
Safety file
• See recommendations by Technical Board
– https://edms.cern.ch/project/CERN-0000094595
• Submit response to [email protected] ADVANCE TO BEAM TIME!
29/5/2015