installation and operation manual - yachtronics seatel... · web: march 4, 2005 document. no....

Sea Tel, Inc.4030 Nelson AvenueConcord, CA 94520Tel: (925) 798-7979Fax: (925) 798-7986Email: [email protected]: www.seatel.com Look to the Leader. Look to Sea Tel.

Sea Tel EuropeUnit 1, Orion Industrial CentreWide Lane, SwaythlingSouthampton, UK S0 18 2HJTel: 44 (0)23 80 671155Fax: 44 (0)23 80 671166Email: [email protected]: www.seatel.com

March 4, 2005 Document. No. 122596Revision A

INSTALLATION AND OPERATION MANUALFOR SEA TEL MODEL

TSC-10 TOUCH SCREEN CONTROLLER

ii

Sea Tel Marine Stabilized Antenna systems are manufactured in the UnitedStates of America.

Sea Tel is an ISO 9001 registered company. Registration Number M2314 whichwas first issued on November 09, 1998.

The Series 04 Family of Marine Stabilized Antenna Pedestals with DAC-2200Antenna Control Unit complies with the requirements of European Norms andEuropean Standards EN 60945 (1997) and prETS 300 339 (1998-03). Sea TelEuropean Union Declaration of Conformity for this equipment is contained in thismanual.

Copyright Notice

All Rights Reserved. The information contained in this document is proprietary to Sea Tel, Inc.. Thisdocument may not be reproduced or distributed in any form without the consent of Sea Tel, Inc. Theinformation in this document is subject to change without notice.

Copyright © 2005 Sea Tel, Inc.

iv

Revision History

REV ECO# Date Description By

A N/A March 4, 2005 Initial Release MDN

Table of Contents

v

1. INTRODUCTION .................................................................................................................................1-11.1. GENERAL DESCRIPTION OF SYSTEM.................................................................................................1-11.2. GENERAL SCOPE OF THIS MANUAL....................................................................................................1-11.3. QUICK OVERVIEW OF CONTENTS......................................................................................................1-1

2. OPERATION........................................................................................................................................2-12.1. QUICK START..................................................................................................................................2-12.2. HOME PAGE....................................................................................................................................2-22.3. ANTENNA - SETTINGS MENU ..........................................................................................................2-42.4. ANTENNA - SHIP MENU..................................................................................................................2-62.5. ANTENNA - INFO MENU ..................................................................................................................2-72.6. SATELLITE SUB MENUS ....................................................................................................................2-82.7. DIAGNOSTIC SUB MENUS..................................................................................................................2-82.8. SETUP SUB MENUS..........................................................................................................................2-8

3. INSTALLATION...................................................................................................................................3-13.1. CABLE INSTALLATION.......................................................................................................................3-13.2. RACK MOUNT INSTALLATION ............................................................................................................3-13.3. BULKHEAD MOUNT INSTALLATION ....................................................................................................3-1

4. SETUP.................................................................................................................................................4-14.1. SATELLITE - SELECTION MENU.......................................................................................................4-14.2. SATELLITE - EDIT MENU.................................................................................................................4-24.3. SATELLITE - PRESETS MENU..........................................................................................................4-44.4. SETUP MENU..................................................................................................................................4-54.5. SETUP - HARDWARE MENU ...........................................................................................................4-64.6. SETUP - TRACKING MENU .............................................................................................................4-74.7. SETUP - BLOCKING MENU .............................................................................................................4-84.8. SETUP - DATE/TIME MENU ............................................................................................................4-9

5. FUNCTIONAL TESTING.....................................................................................................................5-15.1. ANTENNA CONTROL UNIT CHECKS ...................................................................................................5-15.2. TOUCH SCREEN CONTROLLER CHECKS: ...........................................................................................5-1

5.2.1. Menu Switching ................................................................................................................5-15.2.2. Video Window ..................................................................................................................5-15.2.3. Lock Mode........................................................................................................................5-15.2.4. Sleep Mode/Screen Blanking Mode .................................................................................5-1

6. MAINTENANCE & TROUBLESHOOTING.........................................................................................6-16.1. GENERAL CAUTIONS & WARNINGS ..................................................................................................6-16.2. TROUBLESHOOTING THE TOUCH SCREEN CONTROLLER (TSC-10)....................................................6-1

6.2.1. Screen is Blank, Sea Tel Logo is NOT lit, Power LED is OFF and Lock LED is OFF; ....6-16.2.2. Screen is Blank, Sea Tel Logo is back-lit, Power LED is OFF and Lock LED is OFF; ....6-16.2.3. Screen is Blank, Power LED is ON and Lock LED is OFF;..............................................6-16.2.4. Screen is Blank, Power LED is ON and Lock LED is ON; ...............................................6-2

6.3. SATELLITE - ANALYZER MENU........................................................................................................6-26.4. DIAGNOSTICS - SELF TEST MENU ..................................................................................................6-36.5. DIAGNOSTICS - TROUBLE SHOOTING MENU....................................................................................6-46.6. DIAGNOSTICS - STRIP CHART MENU...............................................................................................6-66.7. DIAGNOSTICS - STATUS LOG MENU................................................................................................6-7

Table of Contents

vi

7. TSC-10 TECHNICAL SPECIFICATIONS............................................................................................7-17.1. TSC-10 TOUCH SCREEN CONTROL PANEL (OPTIONAL)....................................................................7-17.2. “M&C” SERIAL INTERFACE FOR TSC-10 TOUCHSCREEN CONTROL PANEL ........................................7-17.3. “ETHERNET” INTERFACE FOR TSC-10 TOUCHSCREEN CONTROL PANEL............................................7-17.4. M&C CABLE ...................................................................................................................................7-1

8. DRAWINGS.........................................................................................................................................8-18.1. TSC-10 TOUCH SCREEN CONTROLLER DRAWINGS ..........................................................................8-1

TSC-10 Touch Screen Controller Introduction

1-1

1. IntroductionThis manual describes the Sea Tel Model TSC-10 Touch Screen Controller. Operating instructions, systeminformation, installation, setup, functional testing and maintenance for the TSC-10 are also contained herein.

This Touch Screen allows you to monitor and control the Sea Tel Stabilized Antenna Pedestal through theAntenna Control Unit that it is connected to.

1.1. General Description of systemThe TSC-10 Touch Screen Controller provides a user friendly graphic interface which you will use to remotelymonitor and control the Sea Tel Stabilized Antenna and its Antenna Control Unit. It has been designed andmanufactured so as to be inherently reliable, easy to maintain, and simple to operate. Except for start-ups, orwhen changing to operate with different transponders or satellites, the equipment essentially permitsunattended operation.

The panel accepts an NTSC, or PAL, composite video input from any source you would like to monitor. Thevideo input is seen in a minimized window in the upper right area of the panel. When the panel is not beingused to monitor or control the antenna, simply touching the minimized external video window will expand it tofull screen. When you want to use the panel to control the antenna, touch anywhere on the screen tominimize the external video window.

The TSC-10 will be connected to the Antenna Control Unit and becomes part of your Below-DecksEquipment (BDE) group.

The following text provides a basic functional overview of the system components and componentinterconnection as referred to in the System Block Diagram(s) for your model antenna.

Television Receive Only (TVRO) Systems are comprised of two major sections: The Above-DecksEquipment (ADE) is comprised of the Sea Tel antenna & radome assembly which is mounted outside, on anupper deck location chosen for best satellite reception. The Below-Decks Equipment (BDE) includes theAntenna Control Unit and will have satellite receiver(s), TV set(s) and all other ancillary equipment that ismounted in various locations throughout the interior of the ship.

1.2. General scope of this manualThis manual describes the Sea Tel Model TSC-10 Touch Screen Controller, its’ operation and installation.Refer to the manuals provided with your Sea Tel Stabilized Satellite Antenna, and its Antenna Control Unit,for installation and operating instructions for those equipments.

1.3. Quick Overview of contentsThe information in this manual is organized into chapters. Operation, basic system information, installation,setup, functional testing, maintenance, specifications and drawings relating to this TSC-10 Touch ScreenController are all contained in this manual

Introduction TSC-10 Touch Screen Controller

1-2

This Page Intentionally Left Blank

TSC-10 Touch Screen Controller Operation

2-1

2. Operation

2.1. Quick Start

This page is used to display, or edit, the antenna position,functional settings, LNB type and history of recent AGC(signal level) values.

This page is used to display, or edit, the ships Latitude,Longitude and Heading information.

This page displays the Model, Serial Number and SoftwareVersion information from the Antenna Pedestal, the AntennaControl Unit and the Touch Screen Controller.

This page shows all the viewable satellites in yourgeographic location. You can target one of the satellites inthe scroll list or the graphic arc below.

Used to edit the satellite database stored in the panelmemory.

This menu is used to set or change the "favorite" satellitesdisplayed on the Home Page of your Touch Screen Controlpanel.

This page provides a spectrum analyzer display of frequencyversus amplitude of the current satellite signal input to thetracking receiver.

Run, or view the results of, Self Test Diagnostics that theantenna ran during initialization or that you run now. Thisfeature is not available in the current software.

Very basic "operator" troubleshooting is programmed into thepanel to help you isolate some very basic failures. If thisbasic troubleshooting does not restore normal operation,these pages will guide you to capture the error/status log andcontact your dealer to report the information and arrange forrepairs.

Provides a diagnostic strip chart recording of antennaperformance. It is an excellent tool for a technician to use tocapture an intermittent problem in the system.

Log of events and status messages that have occurred in thepast 24 hours.

This page is used to view and edit the parameter settingsand the currently installed LNB. The LNB type is used todetermine which satellites you could target and track. Thesystem will not let you target a satellite that your LNB cannotreceive.

View and edit the current Tracking settings for the system.

Used to map out the blockage caused by the ships structure.The blockage can be mapped through the full 360 degrees ofRelative position around the antenna in 15 degree segments.Each Relative segment can also be mapped in Elevationfrom 0 to 90 degrees.

Allows you to set the correct Date and Time into the panel.

Home PageDisplays the Ship andAntenna information,

Status, recent ReceiveSignal, Favorite Satellite

targeting buttons, the fourMain Menu buttons andminimized Video input

window.

Once the system has been set-up, the Home Page provides allof the most frequently neededinformation and the mostfrequently used buttons.

The screen will blank if it hasnot been touched for one hour,except when it has been left infull screen video mode. If thescreen has gone blank (powerlight and back-lit logo are ON,but the screen is black), touchanywhere on the screen torestore the previously viewedpage.

The Home Page can beaccessed from any other menulocation by pressing the Homebutton.

Passwordrequired

Operation TSC-10 Touch Screen Controller

2-2

2.2. Home PageOnce the system has been set-up, the Home page provides all of the most frequently needed information andmost frequently used buttons. The screen will blank if it has not been touched for one hour, except when ithas been left in full screen video mode. Blanking the display extends the life of the LCD panel. You can tellwhen blanking is ON because the power light and back-lit logo will be illuminated, and you can touchanywhere on the screen to restore the previously viewed page. When power has been turned OFF thedisplay will be blank AND the power light will be extinguished. The Home Page can be accessed from anyother menu location by pressing the HOME button.

Status Bar - The Status Bar provides the Pedestal Model number, Pedestal (PCU) Status and systemStatus. Pedestal Model number and status information come from the Pedestal Control Unit (PCU). Thesystem status comes from the Antenna Control Unit (ACU) & the PCU.

AZ/REL/HDG Graphic - Azimuth, Relative and Heading values from the ACU are displayed in numeric andin graphic form. The graphic is comprised of an antenna centered on an overhead outline of a ship, which issurrounded by a true North compass rose. This indicates where the bow of the ship is pointed in reference totrue North (based on the Heading input from the ships Gyro Compass). The Antenna position is indicated intwo references; Where it is pointed relative to the bow of the ship (Relative) and where it is pointed inreference to true North (Azimuth).

EL Graphic - The Elevation graphic indicates where the antenna is currently pointed in elevation. Theelevation angle will be between 00.0 degrees (horizon) and 90.0 degrees (zenith).

Receive Signal Level Graphic - The current AGC and Threshold values from the ACU are used to updatethis histograph. The AGC value is displayed in numeric and graphic forms. The graphic form of AGC isAmplitude (vertically) and Time (horizontally) to provide the short term history of the AGC value. Theamplitude of the AGC LEVEL and the Threshold value, are graphically displayed. Whenever AGC is greaterin value that the Threshold setting, vertical AGC lines will be blue, indicating that a good satellite signal levelis being received. When the AGC value falls below the current Threshold value the vertical AGC lines willchange color to red, indicating that the satellite signal is too low. The system will time out and beginsearching to re-acquire the desired satellite. The system may find other satellite signals that are greater levelthan the Threshold value, but will continue searching if the signal does not match all of your desired satellitesettings.


2-3

Video Input Window (Minimized) - If a composite video input (NTSC or PAL) is connected to the rearpanel, it will be displayed in this minimized window. This allows the panel to display video from any desiredsource while it is not being used to control the antenna. If you touch the minimized window, the video displaywill “maximize” to full screen. When maximized, touch anywhere on the screen to “minimize” the videodisplay. When the video window is minimized, the screen will blank after one hour of inactivity. When thevideo window is maximized, the screen will NOT blank.

Presets 1-5 (Favorite Satellites) - Five Preset buttons can be configured to be your “Favorite Satellites”from the Satellite – Presets menu. To target a satellite, or switch from the satellite you are on to another,you simply touch the desired Preset satellite button you want and then touch the Enter button.

You can create Presets for different feed configurations (Interchangeable LNBs) or for different geographicareas that you periodically travel to. If you select a satellite that would require an elevation of zero, or less,“Satellite Out Of Range” (satellite is below the horizon) will be displayed in System Status on the Status Barand the satellite will NOT be targeted. If you select a satellite that does not match the current configuration ofyou feed (polarization type and/or frequency band), “Frequency Is Not Supported By LNB” will be displayed inSystem Status on the Status Bar, but the satellite you selected will be targeted if the elevation is above thehorizon.

Main Menu Buttons - There are four main menu buttons, each having sub-menu buttons to divide thefunctions of the Touch Screen Controller into groups. The main menu buttons are Antenna, Satellite,Diagnostics and Set Up.

Antenna - The Antenna main menu button accesses the Antenna related sub-menus; Settings, Shipand Info.

Satellite - The Satellite main menu button accesses the Satellite related sub-menus; Selection, Edit,Presets and Analyzer.

Diagnostics - The Diagnostics main menu button accesses the Diagnostics related sub-menus; SelfTest, Troubleshooting, Strip Chart and Status Log.

Set Up - The Set Up main menu button prompts you for a password and then allows you access to theSet-Up related sub-menus; Hardware, Tracking, Blocking and Date/Time.

Display Lock - Press to “Lock” the display. You may wish to lock the panel while you clean the screen.When locked, the display will blank and will NOT respond to touches on the screen and the red LED to theleft of the Lock button will illuminate. When unlocked, the red LED will be OFF and the panel will respond totouches on the screen.

Power ON/OFF Switch - This turns the Touch Screen Controller panel power ON or OFF. When power isbeing supplied to the panel (from the ACU or another source) the Sea Tel logo will be back-lit with blue light.The green power LED to the right of the power button will be illuminated when power is turned ON.


2-4

2.3. Antenna - Settings MenuThis page is used to display or edit the antenna position, functional settings, LNB type and history of recentAGC (signal level) values.

Elevation - This button displays the current elevation angle of the antenna. To change the currentelevation, touch the elevation button to select elevation entry mode. Use the UP or DOWN arrow key to stepthe elevation up or down in 2 tenths of degree increments OR you can use the numeric key pad to type in adesired elevation value, and then press ENTER to target the antenna to the new elevation position.

Azimuth - This button displays the current azimuth angle of the antenna. To change the current azimuth,touch the azimuth button to select azimuth entry mode. Use the UP of DOWN arrow key to step the azimuthup or down in 2 tenths of degree increments OR you can use the numeric key pad to type in a desiredazimuth value, and then press ENTER to target the antenna to the new azimuth position.

Relative - This button displays the current relative position of the antenna. This is the position of theantenna relative to the bow of the ship. If the antenna was installed correctly the antenna will be pointedinline with the bow when the relative position is 360.0. In simple terms Azimuth = Heading + Relative, so asyou change the relative position of the antenna you will also change the azimuth position. To change thecurrent relative, touch the relative button to select relative entry mode. Use the UP of DOWN arrow key tostep the relative (and azimuth) up or down in 2 tenths of degree increments OR you can use the numeric keypad to type in a desired relative value, and then press ENTER to target the antenna to the new relativeposition.


2-5

LNB Voltage - This button displays the current LNB voltage output from the tracking receiver inside theACU to the matrix switch. The voltage output is used to select the polarity of the IF signal which is routedfrom the matrix switch to the tracking receiver. Touch the LNB Voltage button and use the UP or DOWNarrow key to toggle the voltage between 13 and 18 Volts DC. 13 Volts DC selects VERT or RHCP. 18 VoltsDC selects HORIZ or LHCP. Press ENTER to save.

Tone - ON/OFF. This button displays the current 22KHz TONE output state from the tracing receiver insidethe ACU to the matrix switch. The tone output is used to select the band of the IF signal which is routed fromthe matrix switch to the tracking receiver. Touch the Tone button and use the UP or DOWN arrow key totoggle the tone ON or OFF. Tone ON selects high band IF from the matrix switch. Tone OFF selects lowband IF. Press ENTER to save.

Tracking - ON/OFF. This button displays the current Tracking state. Touch the Tracking button to toggleTracking ON or OFF. Press ENTER to save.

Searching - ON/OFF. This button displays the current Searching state. A search will be initiated if the AGClevel falls below, and stays below, the Threshold value for long enough. How many seconds that the systemwill wait before initiating a search is set in the Hardware – Tracking – Search Delay parameter. Touch thesearching button to manually start a search (Searching will go ON) OR to manually stop a search that is inprogress (Searching will go OFF).

Polarization - [Display Only] Displays the current polarization position of the feed.

IF Frequency - This button displays the current IF frequency that the tracking receiver inside the ACU istuned to. To change the current frequency, touch the frequency button to select frequency entry mode. Usethe UP or DOWN arrow key to increment/decrement the frequency in 1 MHz steps Or you can use thenumeric key pad to enter a desired tracking frequency. Press ENTER to retune the tracking receiver in theACU.

NID - [Display Only] Displays the current Network ID being received by the ACU.

LNB Type - [Display Only] Display of the current LNB Type selected in the Setup – Hardware settings.

AGC Histograph - Across the bottom of this display page is a graphic history of the most recent AGCvalues. The values are written on the right side and then move to the left. Therefore, the left end is theoldest data and the right end is the current data.

Whenever AGC LEVEL is greater in value that the Threshold setting, vertical AGC lines will be blue,indicating that a good satellite signal level is being received.

When the AGC LEVEL value falls below the current Threshold value the vertical AGC lines will change colorto red, indicating that the satellite signal is too low. The system will time out and begin searching to re-acquire the desired satellite. The system may find other satellite signals that are greater level than theThreshold value (change to blue lines), but will resume searching if the signal does not match all of yourdesired satellite settings (change to red lines).

While the current AGC value is below the current Threshold value (such as when the antenna is blocked,unwrapping or is searching) the displayed data will be red.


2-6

2.4. Antenna - Ship MenuThis page is used to display, or edit, the ships Latitude, Longitude and Heading information. In somesystems you may not be able to edit the Heading (see Heading information below).

Latitude - This button displays the current latitude of the ship. Latitude is used to calculate Azimuth,Elevation and Polarization values for the desired satellite you have selected. Latitude is automaticallyupdated by the GPS NMEA input. When the GPS input is working properly it will over-write any edit changesyou make.

To manually update, touch the latitude button and key in numeric latitude in decimal form. Tenths may beentered (and will be used internally) but the display will round off to nearest whole degree.

Touch the N/S button and press N/S/E/W to toggle North/South to the correct hemisphere. Press ENTER toset the new latitude.

Longitude - This button displays the current longitude of the ship. Longitude is used to calculate Azimuth,Elevation and Polarization values for the desired satellite you have selected. Longitude is automaticallyupdated by the GPS NMEA input. When the GPS input is working properly it will over-write any edit changesyou make.

To manually update, touch the longitude button and key in numeric longitude in decimal form. Tenths may beentered (and will be used internally) but the display will round off to nearest whole degree.

Touch the E/W button and press N/S/E/W to toggle East/West to the correct hemisphere. Press ENTER toset the new latitude.


2-7

Heading - This button displays the current heading of the ship. This input is used to provide “True” Azimuthantenna position.

If the GYRO TYPE parameter is set to NMEA0183 data or 1:1 Synchro, you will not be able to set Heading toany other value than what it receives from the Ships Gyro Compass (or Satellite Compass).

For all other acceptable Gyro Compass input types the Heading MUST be initially set whenever the ACUpower is turned ON. Press the Heading button and key in the heading value of the Ships Gyro Compass andpress ENTER.

During subsequent normal operation, the Heading value should automatically follow the Ships Gyro Compasscorrectly (Heading value should agree with the value observed on the Gyro Compass).

2.5. Antenna - Info MenuThis page displays the Model, Serial Number and Software Version information from the Antenna Pedestal,the Antenna Control Unit and the Touch Screen Controller. None of the information on this page can beedited.

Pedestal Model - This button is a display of the Model number of the Antenna, returned from the PedestalControl Unit (PCU) mounted on the antenna.

Pedestal PCU Serial Number - This button is a display of the Serial number returned from the PCUmounted on the antenna.


2-8

ACU Model Number - This button is a display of the Model number information returned from the AntennaControl Unit (ACU).

ACU Serial Number - This button is a display of the Serial number information returned from the ACU.

Touch Screen Panel Software Version - This button is a display of the Version of software installed in thispanel.

Touch Screen Panel Serial Number - This button is a display of the Serial number of this panel.

ACU Errors - “No Errors” is displayed if no errors have occurred. If one or more errors have occurred, thebox will be checked and individual errors will be listed. Use the Clear Errors button to clear infrequenterrors. If you have frequent or constant errors, refer to the Troubleshooting section of this manual.

PCU Errors - “No Errors” is displayed if no errors have occurred. If one or more errors have occurred, thebox will be checked and individual errors will be listed. Use the Clear Errors button to clear infrequenterrors. If you have frequent or constant errors, refer to the Troubleshooting section of this manual.

2.6. Satellite sub menusThese sub menu pages are primarily used to configure the Home page for easy operation. Refer to the SetUp chapter of this manual for more information on how to configure your Home page.

2.7. Diagnostic sub menusThese sub menu pages are primarily used to troubleshoot problems with your system. Refer to theMaintenance and Troubleshooting chapter of this manual for more information on how to use the diagnosticscapabilities of your Touch Screen.

2.8. SetUp sub menusThese sub menu pages are primarily used by your dealer to configure your system. Refer to the Set Upchapter of this manual for more information on how to configure your system.

TSC-10 Touch Screen Controller Installation

3-1

3. Installation

3.1. Cable installation1 Install the M&C Cable from the mounting location of the ACU to the mounting location of the

Touch Screen Panel.

2 Connect the cable to the M&C jack (J-3) on the rear of the ACU.

3 Do NOT energize the ACU at this time.

4 If external video input to the Touch Screen Panel is desired, install a BNC-BNC coaxial cablefrom the mounting location of the panel to the location of the equipment which will be supplyingthe NTSC or PAL video output.

5 Connect the BNC cable to the video output of that (video) source.

6 If Ethernet connection to the panel is desired, install an ethernet cable from the mountinglocation of the Touch Screen Panel to the location of the desired PC or network hub device.

7 Connect the ethernet cable to the PC or network equipment’s ethernet RJ-45 port.

3.2. Rack Mount InstallationThe panel for mounting the TSC-10 in a standard 19” equipment rack is PN 123321.

1 Insert the Touch Screen Panel into the 19” rack mounting plate (123321).

2 Mount the panel to the plate by inserting the 8-23 screws (provided in the installation kit) troughthe rack panel and into the threaded holes in the back of the TSC-10.

3 Connect the M&C cable to the 9-pin connector on the rear of the Touch Screen Panel.

4 If external video input was desired, connect the BNC cable to the video input on the rear of theTouch Screen Panel.

5 If an ethernet connection was desired, connect the ethernet cable to the ethernet RJ-45 portinput on the rear of the Touch Screen Panel. .

6 Mount the Touch Screen Panel in the 19” equipment rack.

3.3. Bulkhead Mount InstallationRefer to drawing 123963 to mark cutout and mounting holes in the desired location of the bulkhead.

1 Cut out and drill the desired bulkhead location where the panel will be mounted.

2 Connect the M&C cable to the 9-pin connector on the rear of the Touch Screen Panel.

3 If external video input was desired, connect the BNC cable to the video input on the rear of theTouch Screen Panel.

4 If an ethernet connection was desired, connect the ethernet cable to the ethernet RJ-45 portinput on the rear of the Touch Screen Panel. .

Installation TSC-10 Touch Screen Controller

3-2

5 Insert the Touch Screen Panel into the cut out location.

6 Mount the panel using the appropriate length screws (several different length screws andwashers are provided in the panel’s installation kit) inserted through the bulkhead and into thethreaded hole in the rear of the TSC-10.

TSC-10 Touch Screen Controller Setup

4-1

4. SetupThe following paragraphs provide all of the information that is needed to set up the Touch Screen Controller for theuser. The Home Page can be set up to have your “Favorite Satellites” preset buttons to simplify normal useroperation. Set Up also includes some hardware configuration settings which must accurately reflect the specificantenna hardware that is currently installed.

4.1. Satellite - Selection MenuThis page shows all the viewable satellites in your geographic location, not just your “Favorite Satellites”. Youcan target one of the satellites in the scroll list (these will not all be “Viewable”) or one displayed in the graphicarc below.

All Satellites - This list contains all the satellites which have been programmed into the panel, regardless ofyour location or LNB type. Scroll up or down through the list of satellites in the panels software database. Asyou scroll down through the list, the name and longitude position of the satellite is displayed in the AllSatellites window. When you have the desired satellite displayed, press Select Satellite button to target theantenna to that satellite. Some of these satellites will not be “viewable” (above the horizon) from your locationand will display a “Satellite Out Of Range” error when you try to target them. Some of the others may be

Setup TSC-10 Touch Screen Controller

4-2

above the horizon, but can not be used with the LNB you currently have installed and will display a“Frequency Is Not Supported By LNB” on the Status bar when you try to target one of them. Currently, youcan NOT add satellites to the database.

Viewable Satellites Graphic - Displays all the satellites in the database that are above the horizon fromyour current latitude & longitude AND that are the same frequency band and polarization mode as yourcurrently installed feed/LNB.

The satellites listed on the arc are the satellites that your hardware configuration would allow you to receive.However, these satellites may not necessarily be aiming their signal at your geographic location (refer to thefootprint chart for each of these satellites) AND you must have the correct satellite receiver (with encryptiondecoder and paid subscription) to actually view the signals from them.

If you touch the longitude text of one of the other satellites in this arc, it will be highlighted by the gray circleand its name/longitude will appear in the “All Satellites” window. If you want to switch to this satellite, pressthe Select Satellite button.

If more satellites are “viewable than space allows for in the arc, the arrow buttons at the bottom of each sideof the arc, will scroll down that side of the arc to display the additional satellites. The large arrow (zenithsymbol) on the under side of the arc shows your longitude position on the arc, which is the highest elevationsatellite position possible (in the arc) from your current geographic location. This zenith pointer will also moveas you scroll down one side, or the other, of the arc of satellites.

4.2. Satellite - Edit MenuThis page is used to edit the satellite database stored in the panel memory, but it does not allow you to enteradditional satellites or delete existing satellites.


4-3

All Satellites - Scroll up or down through the list of satellites in the panels software database using thearrow keys to the right of the selected satellite window. As you scroll down through the list, the name andlongitude position of the satellite is displayed. The current settings for the currently selected satellite aredisplayed below the “All Satellites” display.

To edit a setting, touch the value you wish to change and use the Numeric Keypad UP/DOWN or Numberkeys to change the setting and press the ENTER key. When you are finished editing the settings, press theSave Settings button. Factory “Defaults” satellite settings can be restored at any time by pressing theDefaults key (this will overwrite any previously changed settings).

Band - Band setting of the Selected satellite. To change this setting, touch the Band button and scrollthrough the choices by using UP or DOWN arrow key, and then the ENTER key, in the Numeric Keypad.

Tracking Frequency - The Tracking Frequency is the IF frequency which will be used to track the Selectedsatellite. To change this setting, touch the button and type in the desired tracking frequency by using theNumber keys in the Numeric Keypad. The numeric value you enter must be the Intermediate Frequency (inMHz) output of your LNB (950-2150) that you want to use for Tracking. The UP/DOWN arrow keys may beused to increment/decrement the frequency to fine tune it in 1 MHz steps. Set Frequency to 0000 to selectExternal AGC mode, to read input from X1 & X2 terminals on the Terminal Mounting Strip. Press the ENTERkey to set the value.

Symbol Rate - Baud, or Symbol, Rate of the digital signal is used by the tracking receiver for signal lock onthe Selected satellite. To change this setting, touch its button and type in the desired Symbol Rate with theNumber keys, and then the ENTER key, in the Numeric Keypad. Current receivers can be set to any desiredBaud Rate between 3000 and 30000.

FEC - The Forward Error Correction Rate of the digital signal is used by the tracking receiver for signal lockon the Selected satellite. To change this setting, touch its button and scroll through the choices by using UPor DOWN arrow key, and then the ENTER key, in the Numeric Keypad. The selections are: AUTO, 1/2, 2/3,3/4, 5/6, 6/7, 7/8, SCPC and NBIF. The Default setting (AUTO) automatically scans through all the standardDVB & DSS FEC rates.

NID - The Network ID (four digit HEX value) contained in the digital signal is used by the tracking receiver toIdentify this Selected satellite. To change this setting, touch its button and type in the desired NID by usingthe Number keys, and then the ENTER key, in the numeric keypad. Enter a valid NID Hex value, or 0000 tonot use a Network ID, or a pseudo NID (FFFE for DSS signals or FFFD for DVB signals). Use a two keysequence (decimal point followed by a number key) to enter an alpha character. Key “.” then “1” to enter anA up through “.” then “6” to enter an F.

(Example: to enter an NID of 1B3D you would key in “ 1, ., 2, 3, ., 4 “ ).

Forced NID - If the satellite transmits a specific 4 digit hexadecimal NID this setting should be OFF.

If the satellite does NOT generate an NID but does have a unique combination of FREQ, BAUD and FEClock, this setting should be set to ON. The panel will then generate its own unique forced NID (FFFE for DSSsignals or FFFD for DVB signals) to represent the desired satellite. In this case, you must enter this (forced)pseudo NID in the NID setting above.

Polarization - This setting selects which polarization is used for tracking the Selected satellite signal.Caution: Changing this setting requires the Frequency, Symbol Rate, FEC Rate and NID settings to bereviewed/changed also. To change this setting, touch its button and scroll through the choices by using UPor DOWN arrow key, and then the ENTER key, in the Numeric Keypad.

Defaults - Factory Defaults can be restored at any time by pressing the Defaults button (overwriting anypreviously changed settings).

Save Settings - When you are finished editing the settings press the Save Settings button.


4-4

4.3. Satellite - Presets MenuThis menu is used to set or change the “favorite” satellite presets displayed on the HOME page of your TouchScreen Control panel.

All Satellites - This button allows you to scroll up or down through the list of satellites in the panel’ssoftware database using the arrow keys to the left of the selected satellite window. As you scroll downthrough the list, the name and longitude position of the satellite is displayed.

Preset 1 - Preset 5 - Touch the Preset button you wish to change and scroll through the All Satellites list toselect the satellite you want in this Preset. As you scroll through the satellite list in the All Satellites window,you will see the same satellite value appear in the Preset window you are editing. If you want to change thename of the satellite, use the backspace key to delete the text in the preset button and then type in whatevername you want to appear in this Preset location on the Home Page. Press ENTER in the Keyboard to savethe new satellite Preset.

EXAMPLE 1: If I want to set Preset 1 to be Astra 28E satellite. I touch the Preset 1 window, then I press theUP/DOWN arrow keys to the right of the All Satellites window until it (and the Preset 1 window) displays“Astra 28E”. I then press ENTER in the Keyboard to save the new satellite Preset 1. When I press theHOME key to go to the Home page, I now see “Astra 28E” displayed in the first preset oval above the Sea Tellogo. Preset 1 is the upper left oval, Presets 2-5 are in order to the right and down the arc.

EXAMPLE 2: If I want Preset 1 to actually be Astra 28E, but I want to call it “MY-FAVORITE-1”. I touch thePreset 1 window, then I use the keyboard to type MY-FAVORITE-1 in place of Astra 28E. Then I press theENTER key to save the new name for this satellite. (Note that the satellite name in the All Satellites window


4-5

doe NOT change). Now, when I press the HOME key to go to the Home page, I see “MY-FAVORITE-1”displayed in the first preset oval above the Sea Tel logo. From now on, when I press the “MY-FAVORITE-1”oval and then the ENTER oval on the Home page the antenna will target “MY-FAVORITE-1” satellite (which isactually Astra 28E).

4.4. SetUp MenuThis page is for dealers, technicians and other service personnel only. You must enter a password toaccess the Set Up pages. The current password is 8.

Password - Key in the password and press ENTER to gain access to the Set Up sub-menus (Hardware,Tracking, Blocking or Date/Time).


4-6

4.5. SetUp - Hardware MenuThis page is for technicians and other service personnel to properly configure your system. This Hardwarepage is used to view & edit the system parameter settings and the currently installed LNB. The LNB type isused to determine which satellites could be targeted and tracked.

Elevation Trim - Refer to the “Optimizing Targeting” information in your antenna manual for the procedureyou will use to determine what value you will need to enter here, if any. If satellite targeting has already beenoptimized, you should not need to re-optimize it.

To change the value, touch the Elevation Trim button, key in the new value using the numeric key pad andpress ENTER.

Azimuth Trim - Refer to the “Optimizing Targeting” information in your antenna manual for the procedureyou will use to determine what value you will need to enter here, if any. If satellite targeting has already beenoptimized, you should not need to re-optimize it.

To change the value, touch the Azimuth Trim button, key in the new value using the numeric key pad andpress ENTER.

System Type - Refer to the System Type information in the setup chapter of your Antenna, and AntennaControl Unit, manual(s). To change the value, touch the System Type button, key in the new value using thenumeric key pad and press ENTER.

Gyro Type - Refer to the Gyro Type information in the setup chapter of your Antenna Control Unit manual.To change the value, touch the Gyro Type button, key in the new value using the numeric key pad and pressENTER.


4-7

Polang Type - Refer to the Polang Type information in the setup chapter of your Antenna, and AntennaControl Unit, manual(s). To change the value, touch the Polang Type button, key in the new value using thenumeric key pad and press ENTER.

AGC Offset -

AGC Scale - This setting controls the AGC scale factor of the AGC receive level graphic that is displayed onALL pages, the AGC histograph on the Antenna – Settings page, the Satellite – Analyzer graphic display andthe AGC line of the Diagnostics – Strip Chart graphic display.

PAL/NTSC - This button allows you to select the format of the external video input to the panel which will bedisplayed in the minimized video window, or in full screen mode.

LNB Type - If this is not already correctly set, touch the LNB Type button and use the UP/DOWN arrowkeys to scroll through the list of LNB Types. Select the LNB Type that correctly identifies the LNB that youcurrently have installed on the feed assembly of the antenna.

4.6. SetUp - Tracking MenuThis page is used by service personnel to view & edit the current ACU Tracking parameter settings for thesystem. Refer to the Set Up chapters in your Antenna, and Antenna Control Unit, manuals for propersetting of these parameters.


4-8

4.7. SetUp - Blocking MenuThis page is used to map out blockage caused by the ships structure. Any blockage sector can be mappedthrough the full 360 degrees of Relative position around the antenna. The blockage sector is mapped bypressing the AZ LIMIT 1 box and keying in the relative azimuth position of the Left (or CCW) point of theblockage and press ENTER. Then press the AZ LIMIT 2 box to key in the relative azimuth position of theRight (or CW) point of the blockage. Refer to your Antenna, and Antenna Control Unit, manuals for moreinformation about the AZ LIMIT settings.

If a value exists in either of the AZ LIMIT boxes, you will have to press the C key in the numeric keypad toclear the previous value, so that you can enter the new value.


4-9

4.8. SetUp - Date/Time MenuAllows you to set the correct Date and Time into the panel.

Month - This button is used to enter the number of the current Month of the year.

Day - This button is used to enter the number of the current Day of the month.

Year - This button is used to enter the number of the current Year.

Hour - This button is used to enter the number of the current Hour of the day.

Minute - This button is used to enter the number of the current Minute of the hour.

Zone - This button is used to select your current Time Zone (GMT, + number of hours OR – number ofhours).


4-10


TSC-10 Touch Screen Controller Functional Testing

5-1

5. Functional Testing

5.1. Antenna Control Unit checksRefer to the functional testing chapter in your ACU manual for testing of the Antenna and Antenna ControlUnit.

5.2. Touch Screen Controller checks:

5.2.1. Menu SwitchingTouch any of the Main Menu buttons, and then any one of the Sub-Menu buttons, to verify that screenswitches to the selected menu display.

5.2.2. Video WindowTouch the minimized video window. The video window should go full screen. If no video input isconnected, the screen will display only noise (black with small white speckles). Touch the screen again toverify that the video returns to its minimized window in the upper right section of the display.

5.2.3. Lock ModePress the Lock button below the screen and verify that the display does not respond to touches on thescreen while it is locked. Press the Lock button again to unlock the screen and verify that the display doesrespond to touches on the screen.

5.2.4. Sleep Mode/Screen Blanking ModeDo not touch the screen for one hour to allow it to go into sleep mode (screen blank mode). Touch thescreen and verify that it returns to normal display mode. Do not use Full Screen Video mode for thischeck, the screen does NOT blank in full screen video mode.

Functional Testing TSC-10 Touch Screen Controller

5-2


TSC-10 Touch Screen Controller Maintenance & Troubleshooting

6-1

6. Maintenance & TroubleshootingBelow are the common setup, maintenance and troubleshooting facilities of your Touch Screen Controller. Thereis operator trouble shooting for you to use in troubleshooting simple problems with your system but many of thefacilities are intended for a technician from your dealer to use. Also refer to the Maintenance & Troubleshootingsection of your Antenna, and Antenna Control Unit, manuals for additional troubleshooting information.

6.1. General Cautions & Warnings

CAUTION - Allow only an authorized dealer to install or serviceyour Sea Tel System components. Unauthorized installation orservice can be dangerous and can void your warranty.

6.2. Troubleshooting The Touch Screen Controller (TSC-10)

6.2.1. Screen is Blank, Sea Tel Logo is NOT lit, Power LED is OFF and Lock LED is OFF;The Touch Screen Controller gets its operating voltages from the ACU.

1 Verify that the M&C cable is plugged into the ACU and the into TSC-10.

2 Verify that the ACU power is ON.

If the Sea Tel Logo is still not back-lit, contact your dealer for repair.

6.2.2. Screen is Blank, Sea Tel Logo is back-lit, Power LED is OFF and Lock LED is OFF;The Touch Screen Controller gets its operating voltages from the ACU.

1 Press the Power button to turn the TSC-10 ON. If Power LED does not come ON proceed withsteps 2 & 3.

2 Verify that the M&C cable is plugged into the ACU and the into TSC-10.

3 Verify that the ACU power is ON.

If the TSC-10 still does not come ON, contact your dealer for repair.

6.2.3. Screen is Blank, Power LED is ON and Lock LED is OFF;The Touch Screen Controller may be in sleep mode (screen saver mode).

1 Touch the screen to awaken it.

2 If the screen does not awaken, press the Power button to turn power OFF and then turn powerback ON. Allow the screen to reboot.


Maintenance & Troubleshooting TSC-10 Touch Screen Controller

6-2

6.2.4. Screen is Blank, Power LED is ON and Lock LED is ON;The Touch Screen Controller may be in sleep mode (screen saver mode) AND is Locked.

1 Press the Lock button to unlock the screen (Lock LED will go OFF).

2 Touch the screen to awaken it.

3 If the screen does not awaken, press the Power button to turn power OFF and then turn powerback ON. Allow the screen to reboot.


6.3. Satellite - Analyzer MenuThis page provides a spectrum analyzer display of frequency versus amplitude of the current satellite signalinput to the tracking receiver. This input signal will be of the polarization that is currently set in the satellitedatabase (or selected directly in the ACU).

Analyzer - The graph is comprised of Frequency horizontally and Amplitude vertically.

Frequency is from left (lowest frequency) to right (highest frequency) at 40 MHz per division.

Amplitude is vertically from bottom (lowest AGC value) to top (highest AGC value) at a range set by the AutoSet and the AGC counts values are displayed on the left (upper & lower) side of the graph.


6-3

To start a graph, press one of the three frequency range buttons. The spectrum analyzer graph will beginwriting from left to right, as indicated by the heavy black line. The heavy Green line is the current TrackingFrequency setting. Press the Auto Set button to automatically center the amplitude of the display. Use theUP or DOWN arrow keys to move the graphed data up or down in the grid (shifts the AGC values).

This graph can be very useful for verifying that you are receiving good signal level and to identify satellites.Your tracking frequency should be centered on one of the peaks. If your tracking frequency is centered inbetween peaks, it could be because your polarization, or frequency, setting for this satellite is incorrect or youare not on the correct satellite.

6.4. Diagnostics - Self Test MenuNote: This feature is not available in the current software.

This page will be used to run or view the results of a Self Test. The antenna will automatically run the selftest during initialization or will be able to be commanded to run a self test whenever desired.


6-4

6.5. Diagnostics - Trouble Shooting MenuNote: This feature is not available in the current software. Refer to the troubleshooting flowchart onthe next page.

Very basic “operator” troubleshooting is programmed into the panel to help isolate some of the very basicfailure possibilities. If this basic troubleshooting does not restore normal operation, these pages will guideyou to capture the error/status log and contact your dealer to report the information and arrange for repairs.

No

A Failure HasBeen

Reported

An Error HasBeen

Reported

The PanelDisplays AreNot Updating

The SystemIs Frequently,or Constantly,

Searching

Press DIAGNOSTICS ,then SELF TEST, to

view the Failure(s) thathave occurred.

Are all theconnections

OK?

Does theFAILURE re-

occurfrequently orconstantly?

Yes

Repair/re-connectas needed No

Yes

Return to NormalOperation

Press STATUS LOG, then pressSAVE to save the most recent 24

hours of logged status (status events,errors and failures.

Contact your dealer toreport the failure and

arrange for repair.

PressDIAGNOSTICS ,

then STATUSLOG, to view theError(s) that have

occurred.

No


OK?Yes

Repair/re-connectas needed

Press the ACUNEXT key until theSTATUS Menu isdisplayed. Pressthe ENTER key 3times to get to theERROR display.

Press the RIGHTARROW key, then

press the UPARROW key and

then press theENTER key to

CLEAR the ErrorCode (RRRR digits).

The Antenna Displays (AZ, RELor EL) Are Not Updating

The Ships LAT & LON DisplaysAre Not Updating

The Ships Heading Display Is NotUpdating

Are thedisplays

updating now?Yes No

Yes

Check the connectionsbetween the ACU and

the Antenna.Turn ACU Power OFF. Wait 30

seconds and then turn ACU Power ON.

Check the connectionsbetween the ACU, Gyro

Compass and theAntenna.

Check the connectionsbetween the Panel, the ACU,the Gyro Compass and the

Antenna.

No


OK?

Repair/re-connectas needed


System “Tracking” something for short periods of time,then continues “Searching”. No TV from any receiver.

System “Tracking” something for short periods of time, then continues “Searching”. One of the“Tracking” periods I was able to watch TV, but the system continued “Searching” anyway.

System is “Tracking”. But, no TV from any receiver.

System constantly “Searching” butnever finds any signal to Track.

No TV from any receiver.

System is “Tracking”the correct satellite.But, no TV from any

receiver.

No

Yes

Is it rainingheavily now?

Wait until the rain subsides,then retarget the satellite if

necessary.

No

Yes

Is the antennaphysically

being blocked?

Rotate, or move, the ship toa position where the antennawill not be blocked. Retarget

the satellite if necessary.

Press theRESET buttonon the ACU.

Check coax the cablesbetween the Antenna, ACU,

Matrix Switch and Receiver(s)Yes

Are all thecables

connectedproperly?

Repair/Re-connect asneeded, then go back andre-check “Searching and/or

“Tracking” status

No

Check all thesettings in the

“Satellite - Edit”menu.

Are all thesettingscorrect?

Enter correct settings,then go back and re-

check “Searching and/or “Tracking” status

No

Check coax the cablesbetween the ACU,Matrix Switch and

Receiver(s)

Yes

Are all thecables

connectedproperly?

Repair/Re-connectas needed, thengo back and re-

check “Searchingand/or “Tracking”

status

No

Assure that you aretracking the correct

satellite (for your receiver)

Yes

Target the correctsatelliteNo

Are you on thecorrect

satellite?

Are you on thecorrect satellite

now?

Yes

No

No

YesIs the antenna

physicallybeing blocked?

Rotate, or move, the ship to a positionwhere the antenna will not be blocked.

Retarget the satellite if necessary.

Assure thatreceiver(s) andtelevision(s) are

energizedYesAre all units

turned ON?

Energize them and goon to the next step.No

Assure that the television (at each receiverlocation) is set to the correct channel (ie CH2,AUX or LINE) for the input from the receiver.

YesAre all the

televisions setcorrectly?

Change input selectionon the television to the

correct setting.No

Are you nowable to watchsatellite TV?

Yes


No

Does the FAILUREre-occur frequently

or constantly?Yes

Press STATUS LOG, then pressSAVE to save the most recent 24

hours of logged status (status events,errors and failures.

No

/ * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * This feature is not available in the current software * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * \


6-6

6.6. Diagnostics - Strip Chart MenuProvides a diagnostic strip chart recording of antenna performance. It is an excellent tool for a technician touse to capture an intermittent problem in the system.

Center - Press the center button to center the four selected lines of data in the four windows. Only four linesmay be displayed, but all of the data listed in the line assignment paragraph is being recorded.

Line assignment - Each of the four lines (Green, Blue, Magenta and Red) can be assigned to display onevalue of recorded data. The recorded data includes: Elevation, Azimuth, Cross Level, Relative, Heading,AGC, Head+Rel, Relative+ and Heading+. In the screen above the Green line is set to Elevation, the Blueline is set to Azimuth, the Magenta line is set to Relative+Heading (this should be the same as Azimuth ifheading input from the Gyro Compass is good) and the Red line is set to AGC.

The recorded lines left to right in time, the current value is written on the right limit of the display the oldervalues are stepped to the left as the new value is written on the right. Therefore, the oldest sample is thepiece that is farthest to the left, and is just about to be pushed off the left side of the screen.

In very basic terms: The Azimuth, Elevation and AGC (signal) values should stay fairly flat while ON satelliteindicating signal is staying consistently high and the Azimuth & Elevation values are steady (these will changelong term as the ship travels in Latitude & Longitude, but short term they should stay close to the samevalues). If Azimuth, or Elevation, do move from their correct values, the antenna will no longer be pointed atthe peak signal, and the signal level from the satellite should fall. Azimuth is the sum of Heading plusrelative, therefore, as Heading goes UP Relative MUST go DOWN (equal & opposite to the Heading input) forthe antenna to stay ON satellite.


6-7

In normal operation (Tracking the satellite), if you see signal level fall (a sign of the satellite signal being lost),you could look at the other displayed lines to see if you can determine why the signal level is falling. You lookjust slightly to the left of where signal began falling (a few seconds before signal fell). If you see; Elevationmoved first then signal started falling you would know that the antenna mis-pointed in elevation and that iswhy signal fell. Now you would try to find out why elevation moved. If signal fell and none of the other linesappear to have caused it, you would check for blockage or RF signal failure.

Press the Center button to center the lines in the graph.

Press the Save button to save the current screen of data to a file in the panels memory. If you have captureda loss of signal a Technician will be able to view the file on a computer to try to ascertain why signal was lost.

6.7. Diagnostics - Status Log MenuThis page logs events and status messages that have occurred in the system.

UP/DOWN arrow keys - Press the UP or DOWN arrow key to scroll through the events in the log.

Save key - If you are having frequent or constant errors, press the Save key to save the last 24 hours ofdata for your dealer technician to review. He will need to see what events were happening to repair thesystem.


6-8


TSC-10 Touch Screen Controller TSC-10 Technical Specifications

7-1

7. TSC-10 Technical Specifications

7.1. TSC-10 Touch Screen Control Panel (Optional)Dimensions: 12.78 inches wide x 9.25 inches tall x 1.62 inches deepInterfaces: DE-9 for Serial Data and DC power from ACU

BNC for Video Input (NTSC or PAL must be selected properlyselected in the Setup – Hardware settings)RJ45 network connection

Operating System: Embedded LinuxTouchscreen Size: 10.4 inches diagonal, 4:3 aspect ratioDisplay Resolution: SVGABrightness: 300 Nits

7.2. “M&C” Serial Interface for TSC-10 Touchscreen Control PanelCommunications Parameters: 9600 Baud, 8 bits, No parity, 1Stop BitInterface Protocol: Optically Isolated RS-422/RS232Interface Connector: DE9S

7.3. “Ethernet” Interface for TSC-10 Touchscreen Control PanelCommunications Parameters:Interface Protocol:Interface Connector: RJ-45

7.4. M&C CableType: Multi-conductor, twisted pairs, shieldedConductors: 8Connectors: DE-9Part Number: 122709-1 (50 foot)

122709-2 (100 foot)

TSC-10 Technical Specifications TSC-10 Touch Screen Controller

7-2


TSC-10 Touch Screen Controller Drawings

8-1

8. DrawingsThe drawings listed below are provided as a part of this manual for use as a diagnostic reference.

8.1. TSC-10 Touch Screen Controller DrawingsDrawing Title

122073_C1 System, TSC-10 Touch Screen Controller 8-3122214_D Touch Screen Assembly 8-4122709_A Cable Assy, DAC to Touch Panel 8-7123963_A Installation Arrangement 8-9

Drawings TSC-10 Touch Screen Controller

8-2


FIND QTY PART NO DESCRIPTION REFERENCE DESIGNATOR

SINGLE LEVEL MFG BILL OF MATERIAL

REV

0 COMMENT SEE COMMENTS INCLUDE INSTALLATION ARRANGEMENT 123963 W/EACH KIT

EA

1 1 122214 TOUCH SCREEN ASS'YEA D

2 1 122596 MANUAL, TOUCH SCREEN PANEL, I & OEA

3 1 122709-1 CABLE ASS'Y, DAC TO TOUCH PANEL, 50 EA A

4 1 123686 SOFTWARE, TSC-10EA 0.30

5 10 114580-009 WASHER, FLAT, #8, S.S.EA

6 5 114588-192 SCREW, PAN HD, PHIL, 8-32 x 3/8, S.S.EA

7 5 114588-197 SCREW, PAN HD, PHIL, 8-32 x 3/4, S.S.EA

8 5 114588-201 SCREW, PAN HD, PHIL, 8-32 x 1-1/4, S.S.EA

COMMON 122073-1

TSC-10 LCD KIT, 50 FT.

C1REVDRAWING NUMBERPROD FAMILY

04-Mar-05EFF. DATE SHT 1 OF 1



REV

1 1 122832-700589 GASKET, MOISTURE BARRIEREA A

2 1 122832-700590 BEZEL, 10.4 INCH DISPLAYEA B1

3 1 122832-700530 GASKET, TOUCHSCREEN, 10.4 INCH DISPEA A

4 1 122832-700591 SECURE PLATE, 10.4 INCH DISPLAYEA B

5 1 122832-700592 SHIELD PLATEEA B

6 1 122832-700593 I/O PLATEEA A

7 1 122832-700594 SHELLEA A

10 1 122832-600082 DISPLAY, FP, 10.4 INCH SVGA, 300 NIT, AREA A

11 1 122832-650004 TOUCHSCREEN, ACCU TOUCH, 10.4 INCHEA B

12 1 122832-600077 PCB ASS'Y, BACKLIGHT INVERTEREA A

13 1 122832-950158 PCB ASS'Y, ZF TOUCH DISPLAYEA B

14 1 122832-670004 MEMBRANE KEYPAD ASS'YEA B

16 1 122832-800184 CABLE ASS'Y, BACKLIGHT INVERTEREA B1

17 1 122832-800200 CABLE ASS'Y, DISPLAY DATAEA A1

19 2 121226-9771 SPACER, #2 X .19 OD X .19, NYLONEA

33 40 122832-760003 FOAM STRIP, .5 X .125 THKIN A

35 1 123753 FIRMWARE, TSC-10EA

COMMON 122214

TOUCH SCREEN ASS'Y

DREVDRAWING NUMBERPROD FAMILY


9.25

1.66

8.35

6.24

REF.: 122212 TOUCH SCREEN BEZEL.

10.813- .010+.035

1.66

.33

.05ALL AROUND

12.78

.05

NOTES: (UNLESS OTHERWISE SPECIFIED)

3. FINISH: POWDER COAT SHERWIN WILLIAMS P/N HAT2-C0111 (CHAR GRAY TEXT), LIGHT TEXTURE.

ELECTRONICS DEPT. TO MARK PART WITH TSC-10; DRAWING NUMBER AND REVISION AS THEY APPEAR IN THE TITLE BLOCK; AND SERIAL # ON BACK OF THE PANEL.

4

1. MATERIAL: ALUMINUM 6061-T6.

2. REMOVE ALL BURRS AND SHARP EDGES.

8.38

DOCUMENT NO. 117084 REV. C

REVISION

X.XX = .020"+TITLE:

MODEL:3rd ANGLE

X.XXX

ANGLES

PROJECTION

= 30'

= .005"

+-

+-

-DATE:

SCALE:

TOLERANCESUNLESS OTHERWISE SPECIFIED

X.X = .050"-+APPROVED BY:

DRAWING NUMBERSHEET:

DRAWN BY:

DRAWING SIZE: B

TOUCH SCREEN ASSEMBLY

V.S.

1222141 OF 2 D

05-19-04

1:2

XX04

ECO#REV.A N/A 05-19-04

DATEV.S.BY

DRAWING CREATED IN SOLIDWORKS

DESCRIPTIONNEW DRAWINGDIM 10.813 +.035/-.010 WS 10.44. DIM 1.66 WS 1.48.06-21-044489B V.S.

AMNADDED "ELECTRONICS DEPT. TO" TO NOTE 4. DRAWING NUMBER , SER. NO. ETC WERE AT TOP LEFT POSITION ON BACK.08-30-04N/AB1C 4659 11-10-04 REMOVED ITEM 8, (122832-700596 MOUNTING PLATE, MEMBRANE KEYPAD). AMN

4658 11-15-04D ADDED FIRMWARE 123753. AMN

11.50

4.00

5.75

2.00

4.22

4

TSC - 10, SNR: XXXXP/N XXXXXX REV. X

CL

CL


REVISION

X.XX = .020"+TITLE:

MODEL:3rd ANGLE

X.XXX

ANGLES

PROJECTION

= 30'

= .005"

+-

+-

-DATE:

SCALE:

TOLERANCESUNLESS OTHERWISE SPECIFIED



DRAWN BY:

DRAWING SIZE: B

TOUCH SCREEN ASSEMBLY

V.S.

1222142 OF 2 D

05-19-04

1:2

XX04DRAWING CREATED IN SOLIDWORKS



REV

1 1 110935-35 CONNECTOR, D-SUB, DE-9PEA K1

2 1 110935-36 CONNECTOR, D-SUB, DE-9SEA K1

3 50 117231 CONTROL CABLE, CUSTOMFT A1

4 2 112570-11 BACKSHELL, D-SUB, NICKEL PLATED, DE, EA F

5 4 118128-1 SCREW, CAPTIVE PANELEA

6 4 114593-105 SCREW, SOCKET HD, 4-40 x 7/16, S.S.EA

7 4 119961-005 NUT, HEX, SMALL PATTERN, 4-40, S.S.EA

8 8 112267-3 PINS, SNAP N CRIMPEA

9 8 112267-13 SOCKETS, SNAP N CRIMPEA

COMMON 122709-1

CABLE ASS'Y, DAC TO TOUCH PANEL, 50 FT.

AREVDRAWING NUMBERPROD FAMILY


MSF

CABLE ASS'Y, DAC TO TOUCH PANEL

122709 A

4"

11 1/2"

4X 3/16" CLEARANCE HOLESFOR 8-32 MOUNTING SCREWS

8 1/2"CUT OUT INBULKHEAD



2"

11"CUT OUT INBULKHEAD

5 3/4"

6.4

4.5

BULKHEAD CUT-OUT

CL

CL

SCREEN BOTTOM

NOTES: UNLESS OTHERWISE SPECIFIED

1 USE BOLT LENGTH AND NUMBER OF WASHERS AS NEEDED FORTHICKNESS OF MOUNTING SURFACE.

SCREEN TOP TOUCH SCREEN ASS'Y

4X FLAT WASHER, #8

4X 8-32 PAN HD, PHIL SCREW1


REVISION

X.XX = .020"+TITLE:

MODEL:3rd ANGLE

X.XXX

ANGLES

PROJECTION

= 30'

= .005"

+-

+-

-DATE:

SCALE:

TOLERANCES

UNLESS OTHERWISE SPECIFIED



DRAWN BY:

DRAWING SIZE:B

INSTALLATION ARRANGEMENT, TSC-10

V.S.

1239631 OF 1 A

02-02-05

1:2

XX04DRAWING CREATED IN SOLIDWORKS

A N/A 03-04-05 V.S.RELEASED TO PRODUCTION. CHANGED REV. X1 TO A.

ECO#REV. DATE BYDESCRIPTION

installation and operation manual - yachtronics seatel... · web: march 4, 2005 document. no....

Documents