Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

Product Numbers: WS-UPOE-12VPSPL

This publication describes how to install the Cisco 12-Volt Universal Power Over Ethernet (UPOE) pass-through splitter.

The pass-through splitter kit contains the pass-through splitter box (WS-UPOE-12VPSPL) and one of the DC power cords listed in Table 1. You order the DC power cord for your specific application at the time that you order the pass-through splitter box.

Note The DC power cords cannot be ordered separately.

The pass-through splitter is a passive, standalone device for use with Cisco’s proprietary 60 W UPOE+ module (WS-X4748-UPOE+E). The pass-through splitter accepts a 10/100/1000BASE-T signal from the Ethernet module and outputs an Ethernet signal and 12 VDC power to the powered device.

Note The pass-through splitter operates only with Cisco’s proprietary 60 W UPOE+ module and is not compatible with 30 W PoE+ power-sourcing equipment (PSE).

Table 1 Pass-Through Splitter DC Power Cords

Part Number Description

WS-CAB-UPOE-12-9MM 12-mm to 9-mm barrel plugs, 6 ft (1.9 m) (Samsung monitors)

WS-CAB-UPOE-9-9MM 11-mm to 9-mm barrel lugs, 6 ft (1.9 m) (Tandberg telepresence systems)

WS-CAB-UPOE-FLY9MM Flying leads to 9-mm barrel plug, 4 ft (1.2 m) (physical access control applications)

Americas Headquarters:Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Pass-Through Splitter Box Connectors and LEDs

The WS-X4748-UPOE+E module can provide up to 1,440 W of inline power to attached powered devices. The 1440 W limits the module to a maximum of 24 ports at 60 W per port. Additional limitations are set by the number of WS-X4748-UPOE+E modules installed in the switch chassis and the wattage of the power supplies installed in the switch chassis.

The primary two pairs of UPOE IN connector pins (pins 1, 2, 3, and 6) provide Power over Ethernet+ (PoE+) per IEEE standards 802.3af and 802.3at. This connection provides the signal pair and 30 W of power (600 mA at 48 VDC) to the powered device. If the secondary two pairs of UPOE IN connector pins (pins 4, 5, 7, and 8) are configured to provide power, UPOE power (60 W, 5 A at 12 VDC) is available through the splitter box 12V DC OUT connector to operate the powered device.

Pass-Through Splitter Box Connectors and LEDsFigure 1 shows front and rear views of the pass-through splitter box with the major features identified. Table 2 describes the pass-through splitter box LEDs and connectors.

Figure 1 Pass-Through Splitter Box Features

1 Mounting tabs (accepts ANSI No. 6 screws) 4 12V DC OUT connector, 9 mm barrel

2 PoE+ PWR LED 5 12V DC PWR LED

3 PoE+ OUT connector, RJ-45 6 UPOE IN connector

PoE+ OUT

12V DC PWR

12V DC OUT

PoE+ PWR

UPOE IN

1

1

2

3

6

4

5

3311

04

6

1

2

1 35

4

2Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Installing the Pass-Through Splitter Box

Note The combined power output of the PoE+ OUT connector and the 12V DC PWR connector is up to 60 W.

Installing the Pass-Through Splitter BoxTo install the splitter box, follow these steps:

Step 1 Unpackage the pass-through splitter box and the DC power cord for your application.

Step 2 Position the pass-through splitter box near the PoE device.

Note The pass-through splitter box has two mounting tabs (one at either end) that accept ANSI No. 6 size screws. If necessary, the box can be secured to a surface using two screws.

Table 2 Pass-Through Splitter Box LEDs and Connectors

Feature Description

PoE+ PWR LED Green—The UPOE port on the splitter box is connected to an active UPOE port (WS-X4748-UPOE+E Ethernet port operating in four-pair, forced mode) and power is being passed through the splitter box PoE+ OUT port to a powered device.

Note The 12V DC PWR LED is also lit green at this time.

Off—The splitter box is operating under any set of conditions other than the one described above.

PoE+ OUT connector The PoE+ OUT connector provides both the Ethernet signal pair and PoE+ power (30 W) to the powered device.

12V DC PWR LED • Yellow—Only the primary pair of UPOE IN connector pins (RJ-45 connector) are receiving power, or the CLI power inline four-pair forced command is not enabled on the UPOE module port. There is no PoE+ output and there is no 12 VDC available at the 12V DC OUT connector.

• Green—Both the primary and secondary pairs of UPOE IN connector pins are receiving power from the Ethernet module (WS-X4748-UPOE+E).

• Off—Neither of the pairs of the UPOE connector pins are receiving power.

12V DC OUT connector The 12V DC OUT connector passes 60 W (5 A at 12 VDC) of power to the powered device.

UPOE IN connector Located on the pass-through splitter box back panel, the UPOE IN connector receives the Ethernet signal pair and 60 W of power from the WS-X4748-UPOE+E Ethernet module port over a Category 5 TIA-EIA-568-A compliant or better (newer) cable.

3Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Configuring the Device

Step 3 Plug one end of a Category 5 TIA-EIA-568-A compliant or better (newer) interface cable into a WS-X4748-UPOE+E Ethernet module port.

Note To ensure reliable operation and to comply with regulatory limits, the interface cable between the Ethernet module port and the pass-through splitter box should not exceed 328 ft (100 m).

Step 4 Connect the other end of the interface cable to the UPOE IN connector on the pass-through splitter box.

Step 5 Connect a Category 5 TIA-EIA-568-A compliant or better (newer) network interface cable between the POE+ OUT port on the pass-through splitter box and the powered device.

Note To ensure reliable operation and to comply with regulatory limits, the interface cable between the pass-through splitter box and the powered device should not exceed 32.8 ft (10 m).

Step 6 Attach the appropriate DC power cord between the 12V DC OUT connector on the pass-through splitter box and the DC power connector on the powered device.

Configuring the DeviceThe pass-through splitter box cannot be configured. Power configuration is handled through the WS-X4748-UPOE+E Ethernet module that attaches to the pass-through splitter box. For procedures on configuring the WS-X4748-UPOE+E Ethernet module to operate in 60 W mode, see the Catalyst 4500 Series Software Configuration Guide—Release 15.0(2)SG at the following URL:

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/15.02SG/configuration/guide/config.html

SpecificationsTable 3 lists the environmental and physical specifications of the pass-through splitter box.

Table 3 Environmental and Physical Specifications

Specification Value

Altitude Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m)

Temperature Operation: 32° to 104° F (0° to 40° C)

Nonoperation: –4° to 149° F (–20° to 65° C)

Relative Humidity 5% to 90%

Dimensions (L x W x H) 4.2 x 3.0 x 1.0 (106.7 x 76.2 x 25.4 mm) (without tabs)

5.0 x 3.0 x 1.0 (127 x 76.2 x 25.4 mm) (with tabs)

Weight 0.3 lb (136.1 g)

4Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Regulatory Standards Compliance

Regulatory Standards ComplianceThe 12V UPOE pass-through splitter is in compliance with national and international standards as described in Table 4.

Warnings

Statement 1040—Product Disposal

Table 4 Regulatory Standards Compliance

Specification Description

Regulatory Compliance Products with the CE marking indicate compliance with the 2006/95/EC and 2004/108/EC directives, which include the safety and EMC standards listed.

Safety UL 60950-1 Second EditionCAN/CSA-C22.2 No. 60950-1 Second EditionEN 60950-1 Second EditionIEC 60950-1 Second EditionAS/NZS 60950-1GB4943-2001GB9254-2008

EMC—Emissions 47CFR Part 15 (CFR 47) Class AAS/NZS CISPR22 Class AEN55022 Class AICES003 Class AVCCI Class AEN61000-3-2EN61000-3-3KN22 Class ACNS 13438 Class A

EMC—Immunity EN55024CISPR24EN300386KN24

Warning Ultimate disposal of this product should be handled according to all national laws and regulations.

Waarschuwing Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.

Varoitus Tämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.

5Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Warnings

Attention La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.

Warnung Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen.

Avvertenza Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.

Advarsel Endelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og bestemmelser.

Aviso Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.

¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.

Varning! Vid deponering hanteras produkten enligt gällande lagar och bestämmelser.

Aviso O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações nacionais.

Advarsel Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.

6Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Warnings

Statement 1071—Warning Definition

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.

SAVE THESE INSTRUCTIONS

Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

7Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Warnings

Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

8Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Warnings

¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning! VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR

9Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Warnings

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

10Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Warnings

11Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Warnings

12Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Warnings

Statement 1074—Comply with Local and National Electrical Codes

Warning Installation of the equipment must comply with local and national electrical codes.

Waarschuwing Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften.

Varoitus Laitteisto tulee asentaa paikallisten ja kansallisten sähkömääräysten mukaisesti.

Attention L'équipement doit être installé conformément aux normes électriques nationales et locales.

Warnung Die Installation der Geräte muss den Sicherheitsstandards entsprechen.

Avvertenza L'installazione dell'impianto deve essere conforme ai codici elettrici locali e nazionali.

Advarsel Installasjon av utstyret må samsvare med lokale og nasjonale elektrisitetsforskrifter.

Aviso A instalação do equipamento tem de estar em conformidade com os códigos eléctricos locais e nacionais.

¡Advertencia! La instalación del equipo debe cumplir con las normativas de electricidad locales y nacionales.

Varning! Installation av utrustningen måste ske i enlighet med gällande elinstallationsföreskrifter.

13Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01

Warnings

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2012 Cisco Systems, Inc. All rights reserved.

Printed in the USA on recycled paper containing 10% postconsumer waste.

14Installation Note for the Cisco 12-Volt UPOE Pass-Through Splitter

OL-25751-01