instruction manual all-in-one gsm home alarm … manual revised: august 28, 2014 all-in-one gsm home...
TRANSCRIPT
INSTRUCTION MANUAL
Revised: August 28, 2014
All-In-One GSM Home Alarm SystemSB-SP7200-GSM
Page 2
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PRODUCT REFERENCE
REMOTE CONROL
USB CABLE(2) DOOR / WINDOW
UNITS
MOUNTING ACCESSORIES
MOUNTING ACCESSORIES
PIR / MOTION DETECTION
UNIT
MAIN UNIT POWER ADAPTER
Page 3
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PRODUCT REFERENCE
CAMERA LENS
IR LIGHTS
STATUS LIGHT
MOTION SENSOR
LIVE LISTENING MICROPHONE
SIREN SPEAKER
SLOW BLINK Device is searching for cellular signalFLASHES 3 TIMES EVERY 2.5 SECONDS
Connected to cellular signal
LED FLASHES QUICKLY During setup of sensors, unit has connected successfully
STATUS LIGHT
The status light will also blink in other ways depending on the mode you are in. These three status blinks are the most important.
SOLAR PANEL
Your alarm system will automatically switch to IR “Night-Vision” when necessary.
Page 4
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PRODUCT REFERENCE
MICRO SD CARD SLOT
SIM CARD SLOT
LEARN BUTTON
BACK OF MAIN UNIT
(BACK COVER REMOVED)
BOTTOM OF MAIN UNIT
(BACK COVER REMOVED)
ON/OFF SWITCH
CHARGING STATUS
RED - CHARGINGGREEN / OFF - CHARGED
ADAPTER CONNECTION
Page 5
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
Your GSM Alarm System uses text messages to communicate with you. This requires sending the unit particular codes. We have put together a list of codes at the end of this manual, but for now, please follow the instructions in order so that you may best understand how the system works.
REQUIREMENTS:
You should have the following for proper operation of your GSM Alarm System.
1) Your GSM Alarm System, with the Main Unit, Remote Control, Sensors, a Power Adapter, USB Cable and mounting accessories.
2) A micro SD Card, up to 32GB. You can order a compatible card from SafetyBasement.com. Should you already have an SD card, please be sure it has been erased.
3) A cellular SIM card. A compatible card is available from SafetyBasement.com. Please check with SafetyBasement for SIM card requirement before using another card. ANY SIM card will require a monthly fee.
4) A small Phillips head screwdriver.
5) 3 AAA batteries for wireless PIR unit.
INTRODUCTION
Page 6
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
INSTALL THE SD CARD
Slide LEFT to UNLOCK
1. Use your Phillips head screwdriver to remove the screw from the bottom of the main unit.
2. Remove the back of the main unit.3. With a fingernail, carefully push the silver SD Card slot lock to the
LEFT. It will click into the OPEN position.
4. Raise the silver lock to expose the SD card connection.5. Place the SD card in the slot as shown, with the gold connectors
down.
6. Lower the silver lock and slide to the RIGHT to lock the SD in place. It will click into the LOCKED position.
Slide RIGHT to LOCK
Page 7
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
INSTALL THE SIM CARD
Slide UP to UNLOCK
1. Use your fingernail to slide the lock gate UP. It will click into place when UNLOCKED.
2. Raise the lock gate.
3. Insert your SIM Card into the lock gate as shown, with the gold connector facing you, and towards the bottom. The slanted part of the SIM Card will be on the UPPER RIGHT.
4. Close the lock gate.5. Slide the lock gate DOWN to lock your SIM Card in place.
6. Do not replace the back of the unit yet...
Slide DOWN to LOCK
Page 8
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
POWER & CELLULAR SIGNALInsert the power adapter plug into the Main Unit.
The Charging Light should be RED. It will remain red for some time until the backup battery is fully charged.
Turn the Main Unit ON.
Look at the Status Light under the Camera Lense.
Shortly, the Status Light will blink 3 times, every 2.5 seconds. This means that the Main Unit has found a cellular signal and is working properly.
If the status light does not blink like this within 2 minutes, turn off the unit and check the installation of your SD and SIM Cards.
Try again. If the unit does not blink 3 times, every 2.5 seconds, try moving the unit to an area where there may be a better signal.
Try moving on to the next step of this setup to see if you are connected.
If you are unable to connect, you should check to make sure your SIM Card has been properly activated. Contact SafetyBasement or your cellular provider.
STATUS LIGHT
Page 9
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
Your SIM Card has a phone number. You will need this phone number to text or call your GSM Alarm System. Please write this number down. When using the phone number, you will enter an 11 digit number, such as 12345551234. That’s 1, followed by your Area Code, then phone number with NO spaces.
CHECK THE TIME
DEFAULT PASSWORD IS258000
We will be using standard text messages to communicate with the GSM Alarm system. Use your standard text app as you would when texting anyone. TIP! Once you know how to work your GSM Alarm System, use your text app and keyboard shortcuts to making talking to your system as easy as possible. Refer to your phone and text app instructions for shortcuts.A list of codes is at the end of this manual.
ALARM NUMBER IS
MY PASSWORD IS
258000#200# Send this text to the phone number of your SIM card.
>>System time: 16:47 Your alarm should reply within a few seconds with the system time. The time is always on a 24 hour clock / military time.
If the system is not responding, check the format of your text. Make sure you are sending to the complete phone number, 11 digits, no spaces.Your text should also have NO spaces.
Page 10
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
SET THE TIME
258000#03*1700# Send this text to the phone number of your SIM card. In this example, we are setting the clock to 5pm, 1700.
>>Ok, setting successfullyIf you enter the wrong password, the system will not respond as a security feature.
If you enter the correct password, but something is wrong with the format of your command, the system will tell you.
We may need to set the time of day. Remember, the alarm uses a 24 hour clock, military time.
>>Format error, please input the right command!
SET THE LANGUAGE
258000#00*0# Send this text to the phone number of your SIM card. In this example, we are setting the language to English.
>>Ok, setting successfully
This system can respond in English or Chinese. Choose 00*0 for English. 00*1 for Chinese.
Page 11
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
WHO GETS THE ALERTS?
258000#30*1*13215559987#
Device # 1-5. In this example, we are setting the phone number for Device #1.
>>Ok, setting successfully
The system can send alert texts to 1-5 numbers. Let’s set up your first number now. You can go back later to set up additional numbers. Remember to enter your full 11 digit phone number.
CHANGE THE PASSWORD
258000#01*123456# In this example, we are setting the passcode to 123456.
>>Ok, setting successfully
So far, so good. So it’s a good time to set the password that you’ll be using from now on. Choose a password, enter it into the manual for reference later.
Note the full 11 digit phone number. Remember, this must be a number that accepts text messages.
NOTE! From now on, we’ll be using “PASS” rather than a number in the examples. Use your new password here.
PASS#200# Test the new password. Request the current time.
>>System time: 17:27
Page 12
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
CONNECT A WINDOW SENSOR
We’re going to connect a sensor, then name it. You will follow this guide for each sensor device you want to add. The system can accept up to 8 sensors. You can give each sensor a name, such as “Garage” or “Kids Room.”
We’ll start with a Door / Window Sensor. These work by detecting when the magnet has been pulled out of range of the sensor.
LEARN BUTTON PULL BATTERY TAB
MAGNET
SENSOR
1. Pull the battery tab from the bottom of the Window Sensor. The red status light should blink briefly.
2. Place the magnet next to the sensor.3. On the Main Unit, press the LEARN BUTTON. The unit will beep.4. Now, remove the magnet from the sensor.5. The Main Unit will beep. The status lights on the Main Unit and Window Sensor will blink.6. The Window Sensor is now connected wirelessly to the Main Unit.
Page 13
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
MAGNET
SENSOR
NAME A SENSOR
PASS#81*01*Side Door#
Device # 01-08. In this example, we are setting the name for Device #01.
>>Ok, setting successfully
Each sensor can have a name. We are going to name this Window Sensor “Side Door.” It’s Sensor #1 out of 8 possible sensors.
Your Sensor Name CAN include spaces, but your total text message should be less than 48 characters.
Sensor #’s are determined by the order they are connected to the Main Unit. Keep track!
You can repeat this setup for the next Window Sensor at another time. Let’s connect the PIR / Motion Detector Sensor.
Page 14
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
CONNECT THE PIR SENSOR
LEARN BUTTON ON / OFF SWITCH
1. Be sure the On/ Off Switch is in the OFF position.2. Remove the battery cover from the back of the PIR Sensor.3. Insert 3 AAA batteries into the Sensor. Note the placement of the + and - ends of the
batteries.4. Put the battery cover back on.5. On the Main Unit, press the LEARN BUTTON. The Main Unit will beep.6. Turn on the PIR sensor.7. Press the LEARN BUTTON on the back of the PIR sensor. The Main Unit will beep.8. Your PIR Sensor now connected.
Page 15
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PASS#81*02*Garage#
Device # 01-08. In this example, we are setting the name for Device #02.
>>Ok, setting successfully
In the setup we’ve been following, the PIR Sensor was added as the 2nd device, #2. We are going to name Device #2. We’re going to place this sensor in the garage, so let’s name the device “Garage.”
Your Sensor Name CAN include spaces, but your total text message should be less than 48 characters.
NAME THE PIR SENSOR
Now, following the previous steps, continue to add up to 8 devices to your system, until complete.
Page 16
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PASS#80*Alarm At Home!#
>>Ok, setting successfully
The main unit will send you a default message “N2 Emergency Alarm!” You can change this message. Make sure the total number of characters in your text is under 48. Note that the Main Unit is #80.
We are changing our alert message to “Alarm At Home!” Spaces are allowed in the message.
MAIN UNIT MESSAGE
PASS#06*1#
>>Ok, setting successfully
You can receive texts about the power status of the System and the wireless sensors. You’ll want to know when a unit is low on power.
Use 1 to turn on power messages. Use 0 to turn off power messages.
POWER REMINDERS
Page 17
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PASS#07*01#
>>Ok, setting successfully
The siren on the Main Unit can run for 1 to 30 minutes. It can also be set to Silent Alarm. You will want to test your Siren at least once, so let’s set it for 1 minute.
We have set the siren to run for 01 minute.
THE SIREN
PASS#07*00#
>>Ok, setting successfully
Later, when you know the siren is working properly, you can set it to the length of time you want. Or, set it for Silent Alarm. A Silent Alarm will NOT use the siren, but will send you text alerts and record video.
Use 00 to set the Silent Alarm.
SILENT ALARM
Page 18
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
99113377#
>>System reset
If you need to start over, are moving the system to a new location, or any other reason you need to reset all the settings in your system, use this command. It does NOT require the password.
You will lost ALL settings with this command.
RESET - IF YOU NEED IT
DO NOT RESET NOW! Use only if needed.
PASS#21*0#
>>OK, setting successfully
You can quickly delete the Wireless Sensors from the Main Unit, should you need to reset their locations, or start over.
You will lost ALL wireless sensor settings with this command.
DELETE WIRESS SENSORS
DO NOT USE NOW! Use only if needed.
Page 19
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
The Remote Control activates your Alarm System (ARM) and turns it off (CLR). We are going to turn the system on, and set off the alarm as a test.The siren is quite loud! Protect your hearing during this test! Be prepared to press CLR on the Remote Control to turn off the siren as quickly as possible.
ARM BY REMOTE
Press ARM to Arm your alarm system.
Press CLR to shut off the siren and disarm the system.
Press the ARM button, and the system will arm itself in 30 seconds. Normally, you will have 30 seconds to leave the area. For this test, remain near the unit, protect your hearing and be prepared to CLR the alarm.
1. Press ARM.2. The Main Unit will beep. The status light will blink during the 30 second countdown.3. The status light will be Steady after 30 seconds. The system is now armed.4. For your test, wave your hand across the sensor of the main unit, or your PIR wireless
sensor, or pull the maget away from the Window sensor.5. The main unit will beep once, then a few seconds later, the alarm siren will sound.6. Press CLR on the remote control to stop the siren and deactivate the alarm.
Alarm at home!
We received 2 messages from our system during the test.Note that the Garage alarm was set off in this test.
Garage
Page 20
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PASS#101#
>>OK, system armed.
A reminder, if you’re satisfied with the siren, you might want to turn on SILENT ALARM for the remainder of testing and during your installation of your devices. Then, set the siren length for your desired time once the system is in place.
Send the 101 command to turn the system ON.
ARM VIA TEXT MESSAGE
PASS#102#
>>OK, system disarmed.
A reminder, if you’re satisfied with the siren, you might want to turn on SILENT ALARM for the remainder of testing and during your installation of your devices. Then, set the siren length for your desired time once the system is in place.
Send the 102 command to turn the system OFF.
DISMARM VIA TEXT MESSAGE
As with the remote control, the system will countdown 30 seconds, then arm.
Page 21
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
You can Arm and Disarm your system using a standard touchtone phone, rather than a text.
ARM VIA TOUCH TONE PHONE
1. Using a touchtone telephone, CALL the SIM number. Use the full 11 digit number.2. The system will answer with a beep.3. Enter your PASSWORD, followed by a Pound Sign. (#) The system will automatically hang
up if you do not enter the password within 10 seconds.4. The system will BEEP with every key you enter.5. When you have enter the proper PASSWORD, it will beep twice.6. Enter 101# to turn ON the Alarm.7. The system will beep twice.8. The alarm will have a 30 second countdown, then activate.
DISARM VIA TOUCH TONE PHONE1. Using a touchtone telephone, CALL the SIM number. Use the full 11 digit number.2. The system will answer with a beep.3. Enter your PASSWORD, followed by a Pound Sign. (#) The system will automatically hang
up if you do not enter the password within 10 seconds.4. The system will BEEP with every key you enter.5. When you have enter the proper PASSWORD, it will beep twice.6. Enter 102# to turn OFF the Alarm.7. The system will beep twice.
If you enter the wrong code, the system will beep three times.
Remember, by using a text message, you will receive confirmation of your commands.
Page 22
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PASS#05*1830*0730#
>>OK, setting successfully
You may wish to have the alarm automatically turn on at a certain time of day, and turn itself off. You can do this by setting a schedule. Keep in mind, the system uses a 24 hour / military clock.In this example, we have set up our Alarm System at our office. The office closes at 6pm, and opens at 8am. We want to turn on the alarm from 6:30pm to 7:30am the next morning.
USE AN ALARM SCHEDULE
PASS#04*1#
>>OK, setting successfully
Send the 1 command to turn the schedule ON.
ARM THE SCHEDULE
SET THE SCHEDULEARM Time DISARM Time
PASS#04*0#
>>OK, setting successfully
Send the 0 command to turn the schedule OFF.
DISARM THE SCHEDULE
Page 23
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PASS#08*0#
>>OK, setting successfully
There may be times when you want to TURN OFF the motion detection on the Main Unit.
MAIN UNIT MOTION DETECTION
DEACTIVATE THE MOTION DETECTIONDISARM Code
PASS#08*1#
>>OK, setting successfully
RE-ACTIVATE MOTION DETECTIONARM Code
Page 24
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PASS#200#
>>System time: 15:21
You can check the system time, status of your alarm, the schedule, and the numbers to be texted during an alarm.
CHECK STATUS
SYSTEM TIME
PASS#201#
>>Arm: 18:30 Disarm: 07:30 [off]
CHECK ARM / DISARM TIME
The arm time is 6:30pm. The disarm time is 7:30am the next day. The alarm schedule is currently OFF.
PASS#202#
>>SMS [1]13215551234[2]---[3]---[4]---[5]---
CHECK NUMBERS TO BE TEXTED
In our example, only 1 text number has been set up.You can have up to 5 numbers to be texted during alerts.
Page 25
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
PASS#203#
>>System status: disarm
CHECK STATUS
IS SYSTEM ARMED?
PASS#100#
LISTEN IN - LIVE MICROPHONE
The system will only call back the number you texted from. It will NOT use the numbers from the alert list.
You can have the alarm system call you back, and you can listen live via the microphone on the Main Unit. Send the command, and within a few seconds, the Main Unit will call you back.
Page 26
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
READY!You are now ready to mount your system and use it. Your system included some basic mounting pieces.
TIP! Remember, you will need to remove the Main Unit from the wall and plug it into your PC when viewing videos. Use a hook to hang your Main Unit on the wall.
TIP! Use Painter’s Tape to test the location of your Windows / Door Units before sticking them in place.
TIP! Aim the Motion Sensors in the general area you want to detect motion in. Avoid pointing at areas that have frequent movement, such as aquariums.
TIP! Keep this manual handy, and write down your SIM #, PASSWORD and the order of your wireless devices. This will make naming them easier later.
TIP! Remember, the system power switch must be OFF to connect via USB.
TIP! Remember, the system power switch must be ON for any of the functions to work.
Page 27
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
VIEWING THE VIDEO
USB PORT on Main Unit
The Alarm System records 640x480 video when the alarm is activated. The videos are saved as files on the SD Card you installed earlier. You can play these files back on your Windows or Mac PC.
1. On the main unit, set the power switch to OFF. The Main Unit must be OFF to access the video files.
2. Plug the small end of the included USB cable into the USB PORT on the Main Unit.3. Plug the other, wide end, of the USB cable into a spare port on your Windows or Mac PC.4. As with any external device, wait for the Main Unit drive to “mount” onto your system This
may take a moment. In some cases, your system may install standard drivers to access the SD Card. This is normal.
5. Your computer will “mount” 2 drives; MainDVD.ISO and UNTITLED. IGNORE MainDVD.ISO.
6. Click on UNTITLED. You may need to Double-Click.7. Inside is another folder called RECORD. Your recorded video files are in this folder. Click or
Double-click to access.8. COPY these files to your main PC for smoother playback, and for archiving.9. You may DELETE the files from this RECORD folder.10. If you DELETE, you must EMPTY YOUR TRASH before removing your Main Unit from
your PC.11. UNMOUNT the 2 folders from your system BEFORE you disconnect the Main Unit from
your PC. You UNMOUNT by (PC) Right-Clicking on Drive, choose REMOVE.
PROBLEMS PLAYING VIDEO?Your videos should play using the built-in video players that come with your Mac or Windows PC. However, should you run into a problem, please try VLC. This free program can play nearly any video file. If VLC is not able to play the file, the file is most likely corrupt and unplayable.VLC can be downloaded here: http://www.videolan.org
Page 28
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
SPECIFICATIONS
MAIN UNIT POWER ADAPTER
9V, 1A OUTPUT
WORKING TEMP -10 - 50 CGSM FREQUENCY 850/900/1800/1900 MHZ Your GSM SIM Card may be
provided by SafetyBasement.com
RF WIRELESS FREQUENCY 433 MHZDOOR SENSOR DISTANCE SUPPORTED
120 METERS DIRECT LINE-OF-SITE
Your distance will vary with walls or other obstacles.
BUILT-IN BATTERY, RECHARGABLE BACK UP
7.4V / 1000 mAh The back up battery will run up to 24 hours.
PIR SENSOR 3 AAA BATTERIESPIR FREQUENCY 433 MHZBATTERY LIFE UP TO 2 YEARS We recommend leaving
Power Status Alerts ON.
VIDEO FILESRESOLUTION 640x480 pixelsFILE FORMAT .AVIVIDEO CODEC JPEGFRAME RATE 30 FPSBIT RATE Approx. 5-6 Kbps
Page 29
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
Remember, each code you send to your GSM Home Alarm System must start with your PASSWORD, which is 6 digits. Then POUND, the CODE, and end with POUND. Please wait for the device to respond before sending your next code. You may try again if no response in 60 seconds.
TEXT CODES
ARM ALARM SYSTEM PASS#101# Activates your alarm systemDISARM ALARM SYSTEM PASS#102# Deactivates your alarm
systemSET NEW PASSWORD PASS#01*123456# Default password is 258000.
Start your text with 258000 to change password to your new 6 digital code. This example changes the code to 123456.
SET CURRENT TIME PASS#03*1345# Set the current time in a 24 hour clock. In this example, the time has been set to 1:45pm.
ARM / DISARM TIMER PASS#05*2030*0830# Set the schedule you want your system to be on using a 24 hour clock. In this example, the alarm is armed from 8:30pm to 8:30am. You must turn the timer ON for the timer to activate at the scheduled time.
ARM TIMER PASS#04*1# Activates your alarm using the schedule set above.
DISARM TIMER PASS#04*0# Deactivates the timer.
PASSWORD#CODE#ex: 123456#101# turns your alarm ON
TIP! You may want to use the Keyboard Shortcut feature on your smartphone to set up text replacements, to make using codes daily as simple as possible. You should refer to your phone instructions on how to use this feature.
Page 30
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
TEXT CODES
SET TEXT MESSAGE RECEPIENT #1
PASS#30*1*PHONE# Set the phone number of your phone to get text messages from the alarm. The PHONE number must be 11 digits, including 1, then AREA CODE, then NUMBER without spaces. For example, 123456#30*1*12325551234#
SET TEXT MESSAGE RECEPIENTS #2-5
PASS#30*X*PHONE# You can enter up to 5 numbers to receive texts. Substitute the X with 2, 3, 4 or 5.
CHANGE DEFAULT TEXT ALARM MESSAGE FROM MAIN UNIT
PASS#80*Your Desired Alert Message#
Replace the default message with your own. The total number of characters in this command must be less than 48.
SIREN LENGTH PASS#07*TIME# Set the TIME to 01-30 for your siren to run for 1 to 30 minutes when activated.
SILENT ALARM PASS#07*00# Set the siren length to 00 for a silent alarm. You will receive texts, but siren will not sound.
SET MESSAGE FROM DOOR / WINDOW / PIR SENSORS
PASS#81*01*Bedroom Window#
In this example, we are assigning sensor #01 as the Bedroom Window. You can assign up to 8 sensors. Text message must be under 48 characters.
ACTIVATE PIR ON MAIN UNIT
PASS#08*1# The motion detection is now ON for the main unit.
DEACTIVATE PIR ON MAIN UNIT
PASS#08*0# Turn off the motion detection on main unit.
DEACTIVATE ALL WIRELESS SENSORS
PASS#21*0* Resets all wireless sensors.
Page 31
All-In-One GSM Home Alarm & Video System Product Manual : SB-SP7200-GSM
www.SafetyBasement.com Phone: 877-345-2336 Fax: 888-236-2524
TEXT CODES
POWER STATUS REMINDERS - ON
PASS#06*1# Turn on your power status reminders. Recommended.
POWER STATUS REMINDERS - OFF
PASS#06*0# Turn off reminders.
RESET EVERYTHING NO PASSCODE REQUIRED99113377#
This will set your system back to factory default. The password will return to 258000. You will need to re-enter all your settings.
CHECK CURRENT SYSTEM TIME
PASS#200# Receive the current system time.
CHECK ALARM SCHEDULE / STATUS
PASS#201# See the current alarm schedule and status.
CHECK ALERT NUMBERS PASS#202# See the numbers that will receive text messages.
CHECK ALARM STATUS PASS#203# See the current status of the system.