kia genuine accessories - justanswer - about us |...

Revision Date 9/21/2011

of 22

Vehicle Model Sorento - LX Only Accessory Remote Engine StartModel Year 2011 - 2012 Difficulty ( B )KMA Part No. U8560 1U003

Denotes warnings that may lead toserious physical injury or vehicledamage.

Denotes quality processes to bechecked prior to moving to thenext step.

Denotes cautions to be taken to avoidphysical injury or electronic componentdamage.

Denotes specific tools that are necessaryto complete the step.

Denotes cautions to be taken to avoidvehicle and component damage.

Denotes instructionalstepsnecessary to complete theprocess.

Denotes safety equipment required to beused such as a mask, goggles, rubbergloves, and hearing protection.

Mask Goggles

Rubber Gloves Hearing Protection

Instruction Symbols/ Definitions

KIA Genuine Accessories

Note: Difficulty stated above reflects the minimum level of expertise required to install the accessory ( A ) Customer ( B ) Dealer Technician ( C ) Master Technician

Basic Required Hand Tools

1/4” Drive Rachet1/4” Drive 10 mmSocket

PhillipsScrewdriver(Long and Short) Pliers

Wire Cutter

Alcohol Cleaner

Technical SupportFor Authorized Dealers - (800) 421-3209Hours: 9:00 a.m. - 7:00 p.m. EST Monday thru Friday

9:00 a.m. - 5:00 p.m. EST Saturday

1/4” Drive TorqueWrench Trim Tool

1/4” Drive 3/8”Deep Socket

Notes to the Installer:

Read the entire installation manual prior tobeginning the installation of the accessory.

Factory wire harness colors are subject to change,please use the specified pin # in the harnessconnector to identify the correct wire for T-Tapinstallation.

Ensure that the vehicle is properly protected in thearea that the accessory is to be installed.

To prevent vehicle damage, never place tools on topof painted surfaces, seats, dash pad, console or floorcarpet / mat.

Always wear appropriate safety gear to includegloves and eye protection when required.

Prior to disconnecting the negative lead to thebattery, note the AM/FM and satellite set frequencieson the inspection page, if applicable.

To prevent stress on the remote start wire harness,ensure the tilt/telescopic steering column is fullyextended, if equipped.

Ensure the transportation fuse is properly installedbefore performing the function check on page 15.

Ensure vehicle is equipped with automatic transmission, power door locks and powerwindows. If the vehicle is not equipped with these options, do not proceed. Ensurevehicle does NOT have SMART KEY.

P/N: 4280256, Rev. D

!


of 22

1 2 3 4 5

InstallationInstructions

Owner’s Guide

HardwareKit

6

Control Module P/N: U8560 00002DNA P/N: U8562 00016

P/N: UM040 AY136 P/N: U8560 00000

15 8” Wire Tie (Small)

P/N: XMIN-U8560 1U003-DP

Warning Label 15” Wire Tie (Large)

5 Female T-Tap

25

Hardware Kit Total

Hardware Kit Overview

A B

7

P/N: U8561 1U002 (With HVAC1 Relay)

108

Quick ReferenceGuide

10 6 15” Wire Tie (Large)

9

No. Qty. Description No. Qty. Description No. Qty. Description

1

2

3

4

5

6

7

8

9

Control Module/DNA

Dipole Antenna

Transmitters

Wire Harness

Hardware Kit

KIA Genuine Accessories

Installation Instructions

Owner’s Guide

Quick Reference Guide

Warning Label

1

1

1

2

1

1

1

1

1

Kit Overview

1 #10-24 Serrated FlangeHex Nut

D

1 #10-24 Serrated FlangeHex Bolt (Silver)

E

OE Transmitter Envelope 11 1

11

“Contained in this envelope are the original transmitters for your vehicle’s remote keyless entry system. Your vehicle has been equipped with a Kia Remote Start System. The transmitters provided with your Kia Remote Start System are to be used in place of the original transmitters. The original transmitters must not be used to operate the locks on a vehicle equipped with the Kia Remote Start System. The original transmitters can cause the vehicle’s alarm system to falsely activate.”

4280379

3 Foam Tape

C


of 22

KIA Genuine Accessories (General Procedures)

INCORRECT INCORRECT

Spade TerminalPointed UP

Spade TerminalPointed DOWN

1. Place T-Tap on vehicle wire.

2. Using pliers, close and crimpT-Tap around vehicle wire.

3. Insert harness wire withmale spade terminal endinto the T-Tap.

**Extreme care must be taken to ensure that the male spadeterminal is inserted into the T-Tap properly.

T-Tap Installation Procedure

Spade Terminal CENTEREDInside Connector

CORRECT

NO GOO DNO GOOD

Disconnecting ConnectorsWhen disconnecting connectors, grasp the connectors, notthe wires.

Locking ConnectorsWhen locking connectors, listen for a click indicatingthey are securely locked.

Wire ColorsWhen a two-color wire is listed, the first color indicatesthe base color of the wire, the second color indicates thecolor of the stripe. For example: Black/White

Black(Base Color)

White(Stripe Color)

Striped Wire Solid Wire

Black Connector DiagramsConnector diagrams may be shown on the harness side or theterminal side, extreme care must be taken to verify proper termi-nal location before a T-Tap connection is made.

Terminal End View

Harness End View

Factory wire harness colors aresubject to change, please use thespecified pin # in the harnessconnector to identify the correct wirefor T-Tap installation.


of 22

*Clean hands.*Set the parking brake and open driver’s door window.*Record radio station presets.*Vehicle must be at room temperature.*Ensure vehicle is equipped with automatic transmission, power door locks and power windows. If the vehicle is not equippedwith these options, do not proceed. Ensure vehicle does NOT have SMART KEY.

*ENSURE THE TILT/TELESCOPIC STEERING WHEEL COLUMN IS FULLY EXTENDED AND LOCKED BEFOREINSTALLING THIS ACCESSORY.

4

Trim Tool

*Remove the driver’s side front door step sill trim by insert-ing the trim removal tool under the trim panel and pryingupward to release the (4) pressure clips.

NOTE

NOTE

NOTE

Trim Tool

KIA Genuine Accessories (Vehicle Disassembly)

2

3

0Vehicle Preperation

11/4” Drive Rachet, 10mm Socket

HoodReleaseLever

PressureClips

PressureClips

NOTE

*Remove the driver’s side dash end cap panel by pryingoutward to disengage the (4) pressure clips.

NegativeBattery Cable

WARNING: / AVERTISSEMENTThis vehicle is equipped with a remote controlled engine starter. To reduce the risk of serious Injury or death, switch engine startersystem into service mode and disconnect the vehicle batterybefore performing any service on the vehicle.Ce véhicule est doté d'un démarreur à distance. Pour réduire les risques de blessures graves ou mortelles, mettre le démarreur à distance en mode service et débrancher la batterie du véhicule avant d'effectuer des travaux d'entretien sur celui-ci.

Fuse Box

Trim Tool

*Remove and isolate the negative battery cable from thebattery.

*Using alcohol, clean the top surface of the underhood fusebox. Ensure the surface is completely dry.

*Remove the backing on the underhood label and mount inplace.

*Carefully pull the weatherstrip away from the side of thedriver’s side kick panel.

*Remove the hood release lever by pulling toward the cen-ter of the vehicle.

*Remove the plastic nut located near the vehicle dashwall,if equipped.

*Remove the driver’s side kick panel from the vehicle bypulling upward to release the push clip and prying towardthe center of the vehicle to disengage the (2) pressure clips.

PlasticNut

Pressure Clips

WarningLabel

Push Clip

WARNING! Shock Hazard. Do not touch vehicle’snegative battery terminal to vehicle’s positive batteryterminal. Serious physical injury or vehicle damagemay occur.

!


of 22

Phillips Screwdriver

NOTE

5


*Remove the (2) phillips screws from the side of the lowerdash finish panel.

*Remove the (5) 10 mm bolts and (1) 10 mm nut securingthe steel knee bolster panel.

*Remove the steel knee bolster panel from the vehicle.

NOTE

71/4” Drive Rachet, 10mm Socket*Remove the (3) phillips screws securing the steering col-umn shroud (1 underneath and 2 behind the steering wheel).Turn the steering wheel for access.

*Pull down to separate (Use trim tool, if necessary) and re-move the lower steering column shroud from the vehicle.

NOTE

8

PhillipsScrews

Trim Tool, Phillips Screwdriver

NOTE

6*Remove the lower dash finish panel by removing the (2)phillips screws from the bottom of the panel. Using atrim removal tool, carefully pry outward to release the (5)pressure clips.

*Remove the OBDII connector from the panel.*Disconnect the remaining connectors, if equipped.

PhillipsScrews

10 mm Nut

10 mm Bolts

Phillips Screw

PhillipsScrews


Pressure Clips


of 22

Alcohol / Cleaner


*Carefully pull the weatherstrip away from the driver’s side“A” pillar.

*Remove the access cover and the single phillips screw fromthe “A” pillar.


NOTE

9

Access Cover andPhillips Screw

*Starting at the top, use a trim tool and remove the driver’sside “A” pillar trim panel by inserting the tool behind thepanel and prying outward to release the (2) pressure clips.

CAUTION! Do not lose the (2) plastic clips.

Trim Tool

NOTE

10

Pressure Clips

*Clean the area of the windshield where the antenna will be mounted with an alcohol-based glass cleaning solution. Ensure theglass surface is completely dry.

*Mount the dipole antenna to the windshield approximately 0.5” below the mirrors lowest attachment point and/or any wind-shield electronic gridwork. Remove protective backing. Press firmly to ensure a good glass to adhesive bond.

1NOTE

KIA Genuine Accessories (Installation)


of 22

*Wrap the antenna cable with (3) pieces of supplied foam tape to ensure that the antenna will stay in place after routing, asshown above.

*Route the antenna cable vertically on the right hand side of the mirror up to the headliner. Tuck the cable behind the headlinerand down the “A” pillar. Use (3) small wire ties to secure the antenna cable to the factory harness located within the “A” pillar.Trim off excess wire ties.

NOTE

2


Trim Tool, Wire Cutter

NOTE

Antenna

16-Pin 24-Pin 10-Pin

*Route the antenna cable past the left side of the dashboard and over to the fuse panel area.*Plug the wire harness and the antenna cable into the remote start module before mounting.*Ensure all connectors are properly locked into position.

CAUTION! Be careful not to bend/damage any of the terminals inside the remote start module.

10"

9"9"

3

!WARNING! Air Bag system interference hazard. DO NOT secure antenna cable to the Air Bag components.Damage to the vehicle’s Air Bag system may occur which could result in serious physical injury.

CAUTION! If the vehicle is equipped with a sunroof, be careful not to place the wire ties around the drain tube orthe sunroof may not drain properly.


of 22


*Route the remote start harness 6-pin male and female ignition connectors upward to the ignition switch.*Disconnect the factory male 6-pin M15 ignition connec-tor and plug in the cooresponding remote start harnessconnectors.

NOTE

5

Remote Start IgnitionConnectors

Steering Column TiltRelease Lever

NOTE

6Wire Cutter

*Route the remote start harness 6-pin male and female key-in-sense connectors along the factory harness toward thefactory 6-pin connector, located to the right of the steeringcolumn.

*Disconnect the factory male 6-pin M37 connector andplug in the cooresponding remote start harness connectors.

*Secure the factory male connector and the remote startharness female connector to the factory connector with (1)small wire tie. Trim off excess wire tie.

Steering Column

NOTE

7Wire Cutter

4-Pin Connectors

*Route the remote start harness 4-pin male and femalebrake switch connectors under the steering column to thebrake switch.

*Disconnect the factory male 4-pin CHG 39 connector andplug in the cooresponding remote start harness connectors.

*Secure the factory male connector and the remote startharness female connector to the remote start harness with(1) small wire tie. Trim off excess wire tie.

Wire Tie6-Pin Connectors

Wire Tie

NOTE

Wire Tie

Fuse BoxHex Bolt & Nut(Hidden From View)

CAUTION! Torque hex nut to specification. Do notover-tighten or damage to mounting tab will occur.

*Secure the upper right side tab of the remote start moduleto the top hole in the factory brace supporting the fuse boxwith the supplied hex bolt and hex nut. Secure the leftside of the remote start module to the factory wireharnesses with (1) large wire tie. Torque the hex nut to 52inch pounds and trim off excess wire tie.

*Secure excess antenna cable with small wire ties, asneeded. Trim off excess wire ties.

41/4” Drive Rachet, 3/8” Socket, TorqueWrench, Wire Cutter

* Torque Hex Nut to 52 inch pounds

WARNING! Engine Stall Hazard. To prevent stresson the remote start wire harness, ensure the tilt/telescopic steering column is fully extended, ifequipped. Ensure all connectors are fully engagedand locked in place. An engine stall could causeserious physical injury or vehicle damage.

!

*Ensure conector isfully engaged andlocked into theignition switch.


of 22

** **

3468910 21314151618 171920 12

*Locate the Gray wire in pin #17 of the 20-pin I/P-F maleconnector.

*Using pliers, crimp a T-Tap on the Gray wire located in pin#17 of the I/P-F male connector.

*Connect the Gray (Rear Defroster Output) wire from theremote start harness to the Gray wire (Pin #17 of the I/P-Fconnector) by engaging the T-Tap. Refer to Page 3 for T-Tap Installation Procedure.

** **

3468910 21314151618 171920 12

I/P-F ConnectorGray WirePin 17

NOTE

9Pliers

** Unplug connector, if necessary, to identify proper pin location

TERMINAL END VIEW**

NOTE

8

I/P-F ConnectorRed/Black WirePin 16

Pliers

*Route the 26-pin male and female connectors, Red/Blackand Gray wires toward the fuse box.

*Locate the Red/Black wire in pin #16 of the 20-pin I/P-Fmale connector.

*Using pliers, crimp a T-Tap on the Red/Black wire locatedin pin #16 of the I/P-F male connector.

*Connect the Red/Black (Hood Ajar Input) wire from theremote start harness to the Red/Black wire (Pin #16 of theI/P-F connector) by engaging the T-Tap. Refer to Page 3for T-Tap Installation Procedure.


TERMINAL END VIEW**


CAUTION! Ensure the correct pin location is identified.There may be several wires of the same/similar color.



of 22

26

*Locate the Green/Orange wire in pin #26 of the 26-pin I/P-E male connector.*Using pliers, crimp a T-Tap on the Green/Orange wire lo-cated in pin #26 of the I/P-E male connector.

*Connect the Green/Orange (Tachometer Input) wire fromthe remote start harness to the Green/Orange wire (Pin #26of the I/P-E connector) by engaging the T-Tap. Refer toPage 3 for T-Tap Installation Procedure.

I/P-E ConnectorGreen/Orange WirePin 26

NOTE

10Pliers


TERMINAL END VIEW**


NOTE

11

*Disconnect the factory male 26-pin BCM-FK connector atthe fuse box and plug in the cooresponding remote startharness connectors.

26-Pin Connectors

Fuse Box



of 22


NOTE

12*Route the portion of the remote start harness containing the Yellow/Black wire, Lt. Blue wire and the 22-pin male and femaleconnectors along the right side of the fuse box to the BCM (Located on the back side of the fuse box).

*Installation Tip - Remove the (2) 10 mm bolts and the (1) 10 mm nut securing the fuse box and tilt it forward for betteraccess to the BCM connectors.

*Disengage the 26-pin BCM-ML connector from the back side of the BCM.*Locate the Lt. Blue wire in pin #21 of the 26-pin BCM-ML male connector.*Using pliers, crimp a T-Tap on the Lt. Blue wire located in pin #21 of the BCM-ML male connector.*Connect the Lt. Blue (Parking Light Output) wire from the remote start harness to the Lt. Blue wire (Pin #21 of the BCM-MLconnector) by engaging the T-Tap. Refer to Page 3 for T-Tap Installation Procedure.

15

13 12

25 23

11 10 9

21

78

19 17

5 4 * **** ** *

* **

26-Pin BCM-ML ConnectorLt. Blue WirePin 21

TERMINAL END VIEW**

Back of Fuse Box

22-Pin BCM-MNConnector

16-Pin BCM-MMConnector

*Disengage the 16-pin BCM-MM connector from the backside of the BCM.*Locate the Yellow/Black wire in pin #2 of the 16-pin BCM-MM maleconnector.

*Using pliers, crimp a T-Tap on the Yellow/Black wire located in pin #2 ofthe BCM-MM male connector.

*Connect the Yellow/Black (Driver Door Unlock Output) wire from theremote start harness to the Yellow/Black wire (Pin #2 of the BCM-MMconnector) by engaging the T-Tap. Refer to Page 3 for T-Tap Installa-tion Procedure.

13Pliers

2

NOTE

16-Pin BCM-MM ConnectorYellow/Black WirePin 2

Back of Fuse Box

TERMINAL END VIEW** 22-Pin BCM-MNConnector

26-Pin BCM-MLConnector

10 mm Bolts

Pliers, 1/4” Drive Rachet, 10 mm Socket

10 mm Nut


CAUTION! Ensure the correct pin location is identified. Theremay be several wires of the same/similar color.

CAUTION! Ensure the correct pin location is identified. There may be several wires of the same/similar color.



of 22

NOTE

14Wire Cutter

*Disconnect the factory male 22-pin BCM-MN connector at theBCM and plug in the cooresponding remote start harnessconnectors.

*Secure the Lt. Blue (Parking Light Output) wire, Yellow/Black(Driver Door Unlock Output) wire and the 22-pin male andfemale BCM-MN remote start harness connectors to the remotestart wire harness with (1) small wire tie. Trim off excess wiretie.

NOTE

15*Locate the 10 mm ground bolt in the left kick panel area.

*Route the Black wire with ring terminal down along the factory wire harness to the factory ground location.

*Remove the 10 mm bolt. Position the black wire with ring terminal over the bolt and reinstall with factory ground wires.

1/4” Drive Rachet, 10 mm Socket


22-Pin BCM-MNConnector

Ground Location

Wire Tie


of 22

Disarm/Programming Button

NOTE

17Wire Cutter

*Secure the remote start harness with (3) large wire ties. Trimoff excess wire ties.

Wire Tie

Wire Ties

NOTE

18Wire Cutter

Wire Ties

*Secure the Black ground wire to the existing factory har-ness with (2) small wire ties. Trim off excess wire ties.

NOTE

16Wire Cutter

*Connect the disarm / programming button to the corresponding remote start module connector (if disconnected).*Secure the disarm / programming button to the remote start harness with (3) small wire ties. Trim off excess wire ties.*Ensure disarm / programming button is secured to the remote start harness in a manner that allows for future serviceability.*Secure the remote start harness to the existing factory harness with (1) large wire tie. Trim off excess wire tie.

Wire Tie(Secure Remote StartHarness to FactoryHarness)

Wire Tie

Wire Ties (Secured to the Remote Start Harness Only)



!


of 22


NOTE

19*Verify all connections are secure as per the installation instructions.*Turn the ignition key to the ON position.*Reconnect the negative battery cable. If the horn begins sounding, press the disarm / programming button with the ignition“ON” to disarm the system.

*Start the vehicle with the key and verify that no Diagnostic Trouble Codes have been triggered. Any DTCs should be resetbefore proceeding to the next step.

*Turn the ignition key to the OFF/LOCK position.


NegativeBattery Cable

WARNING: / AVERTISSEMENTThis vehicle is equipped with a remote controlled engine starter. To reduce the risk of serious Injury or death, switch engine startersystem into service mode and disconnect the vehicle batterybefore performing any service on the vehicle.Ce véhicule est doté d'un démarreur à distance. Pour réduire les risques de blessures graves ou mortelles, mettre le démarreur à distance en mode service et débrancher la batterie du véhicule avant d'effectuer des travaux d'entretien sur celui-ci.

WARNING! Shock Hazard. Do not touch vehicle’s negative battery terminal to vehicle’s positive battery terminal.Serious physical injury or vehicle damage may occur.!


of 22

KIA Genuine Accessories (Function Check)

Remote Engine Start - Make sure the key is removedfrom the ignition switch and the engine hood and rearhatch are closed. Activate the remote start by pressinglock followed by start within 3 seconds.

The parking lights will flash one time, the horn will beep once,then the vehicle will crank and start. Once started, the parkinglights will come on and stay on signifying the engine is running.

Brake Pedal Safety - Press unlock and enter thevehicle. Press the brake pedal.

Key-In-Sense - Insert the ignition key into the ignitionswitch but keep it in the OFF position. Activate theremote engine start using the transmitter.

The parking lights will flash once and the ignition will turn on asif it is going to start. But, the horn will beep twice and theremote engine start will not attempt to start the vehicle since itdetects the key in the ignition. In addition, the driver’s door willunlock and the vehicle’s interior light will illuminate.

Items To Be Checked Results Of The Check

Door Lock - Close the engine hood and all doors andpress the lock button on the transmitter.

Rear Defrost - Activate the remote engine start. Pressthe remote start button on the transmitter a second timeafter the vehicle has started.

Alarm Trigger - Press the lock button on the transmit-ter. Manually unlock any door and enter the vehicle.Repeat this procedure twice, manually opening thehood and then the trunk.

Car Find Feature - Press the find/panic button on thetransmitter. Repeat this process twice.

The parking lights will flash one time to indicate that the vehicleis armed and locked.

The parking lights will flash one time and the horn will beep onetime giving audible confirmation that the vehicle is locked andarmed.

Door Unlock - Press the unlock button on the transmit-ter.

The parking lights will flash two times to indicate that thevehicle is disarmed and unlock the driver’s door only.

The parking lights will flash two times to indicate that thevehicle is disarmed and unlock all remaining doors.

Door Unlock - Press the unlock button on the transmit-ter a second time within 5 seconds of unlocking thedriver’s door.

The vehicle’s interior light should stay illuminated for 1 minuteor until the vehicle ignition has been turned on or the vehicle hasbeen re-armed/locked.

Interior Lamp - Press the unlock button on thetransmitter to disarm the alarm system.

The parking lights will flash one time. Locate the rear defrosterswitch and verify that the indictator portion of the switch isilluminated.

The parking lights will flash and the horn will beep 5 times.Subsequent presses within 5 seconds of the first press will beepthe horn slightly louder.

Hood Safety Switch - Remove the key from theignition and activate the remote engine start. After thevehicle has started, press the unlock button on thetransmitter to disarm the security system and pull thehood release lever to release the hood. Open the doorand exit the vehicle.

The engine/remote start will turn off immediately.

The hood should not have to be lifted to activate the hood safetyswitch.

Door Lock - Press the lock button on the transmitter asecond time within 5 seconds.

The engine/remote start will turn off.

The engine/remote start will turn off, the parking lights will startflashing and the horn will start beeping for up to 30 seconds.


of 22

KIA Genuine Accessories (Function Check)

Items To Be Checked Results Of The Check

Panic Feature - Press and hold the find/panic button onthe transmitter for 3 seconds to activate. Press the find/panic button a second time to deactivate.

The parking lights will flash and the horn will beep randomly forup to 30 seconds.

Quick Stop Feature - Start the vehicle with the ignitionkey. With the vehicle in park and foot off the brakepedal, press the remote start button on the transmitter.Remove the key from the ignition.

Verify that the parking lights turn on and that the vehicle remainsrunning. The driver’s door will unlock (if previously locked).


of 22

NOTE

1*Reinstall the driver’s side “A” pillar trim by engaging the (2) pressure clips.

Pressure Clips

KIA Genuine Accessories (Vehicle Reassembly)

NOTE

2Phillips Screwdriver

*Reinstall the single phillips screw and the access cover.*Reinstall the weatherstrip near the driver’s side “A” pillar.

Phillips Screw and AccessCover

NOTE

3

Phillips Screw

Phillips Screws


*Reinstall the (3) phillips screws securing the steering col-umn shroud (1 underneath and 2 behind the steering wheel).

Turn the steering wheel for access.

NOTE


10 mm Nut

10 mm Bolts

*Reinstall the (5) 10 mm bolts and (1) 10 mm nut securingthe steel knee bolster panel.


of 22


7NOTE

8

HoodReleaseLever

PressureClips

PressureClips

NOTE

*Reinstall the driver’s side dash end cap panel byengaging the (4) pressure clips.

PlasticNut

*Reinstall the driver’s side kick panel by engaging the (2)pressure clips, (1) push clip and (1) plastic nut, if equipped.

*Reinstall the hood release lever.*Reinstall the weatherstrip near the driver’s side kick panel.

Push Clip


NOTE

5

PhillipsScrews


NOTE

6*Reinstall the (2) phillips screws on the side of the lowerdash finish panel.

*Adjust the tilt/telescopic steering column 3 - 4 timesthrough its’ full range of motion to ensure there issufficient slack in the remote start harness at the ignitionconnector and behind the lower dash finish panel.

PhillipsScrews

*Reinstall any connectors, including the OBDII connectorthat may have been removed from the lower dash finishpanel.

*Reinstall the lower dash finish panel by engaging the (5)pressure clips and the (2) phillips screws.

Pressure Clips


!


of 22


*Reinstall the driver’s side front door step sill trim by en-gaging the (4) pressure clips.

NOTE

9

Pressure Clips

*Place both OE transmitters into the provided white envelope.*Place OE Transmitter Envelope, Owner’s Guide and theQuick Reference Guide into the vehicle’s glove box.

NOTE

10

OE Transmitter EnvelopeOwner’s Guide

&QRG

“Contained in this envelope are the original transmitters for your vehicle’s remote keyless entry system. Your vehicle has been equipped with a Kia Remote Start System. The transmitters provided with your Kia Remote Start System are to be used in place of the original transmitters. The original transmitters must not be used to operate the locks on a vehicle equipped with the Kia Remote Start System. The original transmitters can cause the vehicle’s alarm system to falsely activate.”

4280379


of 22

KIA Genuine Accessories (Trouble Shooting)

Item In Question Results Of The Check

Instruction Ref.

Instruction Ref.

Instruction Ref.

Instruction Ref.

Security system does not triggerwhen armed and a door is opened.

SECURITY FEATURES

Security system does not triggerwhen armed and the trunk isopened.

Security system does not triggerwhen armed and the hood isopened.

Security system “Panic” featuredoes not work.

*Verify that the 22-pin connector at the BCM is connectedproperly (Step 14).

Security system does not arm ordisarm.

*Disconnect each connector from the remote start module toverify that no terminals inside the remote start module werebent or damaged (Step 3).

*Verify that all remote start harness connectors are connectedproperly (Step 3).

*Verify that the fuses in the remote start module are installedper the Fuse and Jumper Reference Drawing and are good.

Step 14(InstallationSection)





*Verify that the correct remote start harness wire was connectedproperly to the correct vehicle wire (Step 8).


Instruction Ref.


HVAC 1

HVAC 2

MAIN B+

IGN

DOME LIGHT PK LIGHTS

DOOR LOCKSDR DOOR/TRNK REL

- +

- +

*Verify proper DNA installation.

Fuse and Jumper Reference Drawing


of 22



Instruction Ref.

Instruction Ref.

Instruction Ref.

Instruction Ref.

Instruction Ref.

Instruction Ref.

Instruction Ref.

CONVENIENCE FEATURES

Vehicle will not lock using thetransmitter.

Vehicle will not unlock using thetransmitter.

Vehicle’s parking lights do notflash.

Vehicle’s horn does not sound whenusing the transmitter.

Vehicle find feature does not work.

Poor operating range.

*Verify that the antenna is mounted and routed in the correctlocation (Step 1 & 2).

*Verify that the antenna is plugged into the back of the remotestart module (Step 3).

*Verify that the 26-pin connector is properly connected at thebottom of the BCM (Step 11).

*Verify that the 26-pin connector is properly connected at thebottom of the BCM (Step 11).

Rear defroster does not work.

*Verify that the fuse located under the DNA case top labeled“DOOR LOCKS” is good and installed in the negativeposition per the Fuse and Jumper Reference Drawing.

*Verify that the fuse located under the DNA case top labeled“DOOR LOCKS” is good and installed in the negativeposition per the Fuse and Jumper Reference Drawing.


Step 11 & 13(InstallationSection)




Step 1, 2 & 3(InstallationSection)


*Verify that the 22-pin connector at the BCM is properly con-nected. (Step 14).

*Verify that the fuse located under the DNA case top labeled“PK LIGHTS” is good and installed in the negativeposition per the Fuse and Jumper Reference Drawing.







*Verify that the 22-pin connector at the BCM is properly con-nected. (Step 14).


of 22



Instruction Ref.

Instruction Ref.

Instruction Ref.

Instruction Ref.

REMOTE START FEATURES

Ignition turns on, horn honks 2times and vehicle does not start.Key-In-Sense activated.

*Remove ignition key from ignition cylinder.

*Verify that the 6-pin male and female key-in-sense connectorsare connected properly (Step 6).

Horn honks 2 times and vehicledoes not start. Safety input acti-vated.


*Verify that the 4-pin male and female brake switch connec-tors at the brake switch are connected properly (Step 7).

Vehicle remote starts, but engagesstarter motor too long.


Page 7(Owner’sGuide)

*Verify that the Valet Mode is not engaged - Refer to theRemote Start System Owner’s Guide.

While the vehicle is running duringthe remote start mode, the airconditioning / heater does notoperate.

*Verify that the fuses located under the DNA case toplabeled “HVAC1” and “HVAC2” are good and installedproperly per the Fuse and Jumper Reference Drawing.






*Verify that the 6-pin male and female ignition switch connec-tors are connected properly (Step 5).Step 5

(InstallationSection)

kia genuine accessories - justanswer - about us |...

Documents