mdds presentation
TRANSCRIPT
AlMansoori Directional Drilling Services
Company Background
• 1992 Target Drilling Services established
• 1992 Integrated Drilling Services established
• 1994 Transocean acquire TDS to formqTransocean Petroleum Technologies
• 1998 Dailey acquired both TPT and IDS
• 1998 TIEBO Middle East established in UAE with associated companies
• 1999 Weatherford acquires Dailey and forms Dailey IDS
• 2000 Target Energy Group formed and acquires Dailey IDS
Technology for Well Placement
• 2007 AlMansoori acquires Target Energy Group
AlMansoori Directional Drilling Services
Range of Services
• Well planning engineering and feasibility studies• Well planning, engineering and feasibility studies• Well-bore construction management• Directional drilling
MWD G R i ti it P LWD• MWD Gamma-Resistivity- Pressure LWD• Coil Tubing / Slim Hole / TTRD Drilling• Air / UBD MWD guidance and logging
C i / Li i• Casing / Liner reaming• Specialised drilling tools design and manufacture• Rotary tools • Fishing and milling• Casing drilling and reaming
Technology for Well Placement
AlMansoori Directional Drilling Services
Products
• Performance Drilling PDM Mud Motors 11¼” to 1¾”• Performance Drilling PDM Mud Motors 11¼” to 1¾”• MWD/LWD 9½” to 2 1/2”• Propagation Wave Resistivity 8¼” to 3 1/8”• E-M Telemetry for Air and UBD Applications• Pressure While Drilling for Air and UBD Applications• Near Bit Gamma and Inclination with Short Hop to MWDNear Bit Gamma and Inclination with Short Hop to MWD• Low Cost Curved Drilling Assembly / RST• RST Short Radius Drilling Technology
Technology for Well Placement
AlMansoori Directional Drilling Services
Achievements - MWD/LWD
• First to measure with 4¾” propagation resistivity tool in• First to measure with 4¾ propagation resistivity tool in1996
• First to measure with 3 1/8” propagation resistivity tool in19991999
• Innovative method of data transmission magnetic fields in1999
• Near-bit gamma inclination and short hop technologies• Bore and annular pressure for air and UBD• Complete MWD for air and UBD
Technology for Well Placement
AlMansoori Directional Drilling Services
Achievements - Performance Drilling
• 9 5/8” Mud motor record single bit run of 15,240 ft.9 5/8 Mud motor record single bit run of 15,240 ft. ROP 207ft/hr
• 9 5/8” Mud motor record of 8,631 ft of 12¼” hole in 24 hrs.ROP 539 ft/hrROP 539 ft/hr
• 9 5/8” Mud motor record in cretaceous sequences with onerun at 315ºF
• 9 5/8” Mud motor record of 7 732 ft of 16” hole in 6 5 hours• 9 5/8 Mud motor record of 7,732 ft of 16 hole in 6.5 hours.ROP 420ft/hr
Technology for Well Placement
AlMansoori Directional Drilling Services
Operating Areas
• UK Europe and Sub Sahara Africa Aberdeen• UK Europe and Sub Sahara Africa - Aberdeen•Middle East - Abu Dhabi, KSA, Yemen, Iran,
Iraq and Syria• East Asia - India
Technology for Well Placement
AlMansoori Directional Drilling Services
• Two operating spheres:
– UK( Europe and Sub-UK( Europe and SubSahara Africa)
– MENA
O f• Operating facilities in:
– UK
– France– France
– Syria
– UAE
Key:Office locations
Current/past projects
– IRAN
– SAUDI
Technology for Well Placement
– Operations in over 20 countries
AlMansoori Directional Drilling Services
Performance
• Performed over 90% of the onshore UK directional drilling jobs• Performed over 90% of the onshore UK directional drilling jobssince 1992
• Provided Directional Drilling Services on over 880 wells in theMiddle EastMiddle East
• Serviced over 45 coiled tubing drilling jobs worldwide • TWC has provided MWD/LWD Services on over 562 wells
worldwide• Planned and supervised the drilling of the wells listed below
Well Type Number C ti l W ll 1123Conventional Well 1123Horizontal Well 755 Slimhole Well 138
Technology for Well Placement
CTD Well 87
W ld id Cli t Li t
AlMansoori Directional Drilling Services
Worldwide Client ListAAP (Albania)Adma (Abu Dhabi)Ad (Ab Dh bi)
Enterprise (Ireland)Europa Oil & Gas (UK)E (UK)
Ryan (Canada) Santa Fe (UK)S ll (E t)Adco (Abu Dhabi)
Agip (Sicily)Alkane Energy (UK)Amerada Hess (UK)Amoco (UK)Amoco (USA)
Evergreen (UK) ExxonMobil (UK)Gupco (Egypt)Harrods (Thailand)Independent Energy (UK)International (UK)
Seagull (Egypt) Shell (UK)Star Energy (UK)Statoil (Norway) Talisman (UK)Texaco (UK)Amoco (USA)
Anadarko (USA)Baker (USA)British Gas (UK)Bow Valley (UK)BP (UK)
International (UK)Kerr McGee (USA)Macmoran (USA)Melrose (UK)Murphy (UK)Pentex (UK)
Texaco (UK)Texaco (USA)Tullow Oil (UK)Tullow Oil (Senegal)Total (UK)Poltova / JKX (Ukraine)
Burlington (USA)Chevron (UK)Chevron (USA)ConocoPhillips (UK)Conoco (UK)Conoco (USA)
Petrobel (Egypt)Phillips (UK)Phillips (Norway)Phillips (USA)Phillips (Venezuela)PPC (Ukraine)
Unocal (Thailand) Unocal (UK)UPRC (USA)Vostok Oil (Siberia)Weatherford (Venezuela)Wintershall (Germany)Conoco (USA)
Edinburgh Oil & Gas (UK)ELF (UK)Enterprise (UK)AFPC (Syria)IPR (Syria)
PPC (Ukraine)PR Marriott Drilling (UK)Premier Oil (UK)PTT (Thailand)SPC (Syria)Gulfsands (Syria)
Wintershall (Germany)Wintershall (UK)Zadco (Abu Dhabi)NIDC ( IRAN)Dublin (Syria)Petro Canada (Syria)
Technology for Well Placement
IPR (Syria)DEZPC (Syria)HPC (Syria)
Gulfsands (Syria)Soyuzeneft (Syria)Tatneft (Syria)
Petro Canada (Syria)SSKOC (Syria)HBS (Syria)KEP- Co (Iran)
Quality Management Systems
Quality Management SystemsSystems
Technology for Well PlacementSlide 10 RST Introduction
Quality Management Systems
Quality Systems
•• Quality Management System accredited to BS EN ISO•• Quality Management System accredited to BS EN ISO 9001: 2000
Current certification is valid through December 2009• Current certification is valid through December 2009
• External assessment by Lloyds Register Quality
• Six monthly surveillance programmed for system conformance
Technology for Well Placement
Quality Management Systems
Training and Competence
• Competence portfolios available for all field personnel
• Developing competence portfolios company wide
• In-house assessors and verifiers to national standards
• Continuing employee development and training
Technology for Well Placement
Reliability
Middle East Motor Reliability
Mean Time Bet een FieldTotal FieldC m lati eTool Si e
1012330384 ¾
Mean Time Between Field Failures (MTBFF)
Total FieldFailures
Cumulative Circulating
Hours
Tool SizeOutside Diameter (in)
130945236/
1203224067 ¼
613636806 ¾
615318455
10481616772Total
>567056711 1/4
1309452369 5/8
Technology for Well Placement
Reliability
Middle East MWD Reliability
MTBFFNCi HS i P id d
723128678Total
723128678Directional Gamma MWD
MTBFFNo. Failures
Circ.HoursService Provided
Technology for Well Placement
Directional Drilling Products
Directional Drilling Products
Technology for Well PlacementSlide 15 RST Introduction
Directional Drilling Products
MUD MOTORS
AlMansoori Directional Drilling Services / Target Well Control Limited supply Vector-Drill Mud Motors. These are owned and maintained in Abu Dhabi by Target Well Control Limited. y gTo date, well over 800 runs have been made with Vector-Drills. In Abu Dhabi there is a stock of over 50Vector-Drills ranging from 1-3/4" OD to 11-1/4" OD.
These motors are available in a variety of configurations to suit any drilling requirement.
ROTARY EQUIPMENT
AlMansoori Directional Drilling Services / Target Well Control Limited has the capability of supplying in excess of 15 strings of Rotary Tools including the following tool categories :-
Stabs 3-1/4" - 36" OD Steel & Non MagneticCollars 2-7/8" - 9-1/2" OD Steel & Non MagneticRoller Reamers 8-1/2" - 17-1/2" ODHole Openers 12-1/4" - 24" ODSubs 2-7/8" - 9-1/2" OD Steel & Non MagneticSubs 2 7/8 9 1/2 OD Steel & Non MagneticFlexi Collars 5" - 5-1/2" OD Non Magnetic
Technology for Well Placement
Directional Drilling Products
New 9 5/8” High Torque Low Speed Motor
Super Torque and ERT Power Section
Standard Vector-Drill Motors : 1 3/4" to 11 1/4"
Vector Drill XL Motors : 2 7/8" 4 3/4” 5 0” 6 3/4” and 7 1/4”Vector-Drill XL Motors : 2 7/8 , 4 3/4 , 5.0 , 6 3/4 and 7 1/4
Vector-Drill ST: 9 5/8”
Vector-Drill Plus 2 Motors : 9 5/8”, 4 3/4”
Low Speed Vector-Drills : 6 3/4”, 9 5/8" & 11 1/4"p ,
Low Speed Vector-Drill Plus 2 : 9 5/8"
Technology for Well Placement
Articulated Motors : For High Build-Up Rates
Standard Vector-Drill Specifications
Tool Type Physical Dimensions Operating Data
Outside Diameter
(in)Nomenclature Recommended
Bit Size (in)
Thread Connection (Trip Sub)
(Box)
Thread Connection (Bit Sub)
(Box)
Length (ft)
Weight (lbs)
Flow Rate Range (gpm)
Max Motor Diff Press
(psi)
Bit Speed Range (rpm)
Torque (ft-lbs)
Pow er (hp)
1 3/4 VectorDrill MS 1-7/8 to 2 1/2 AW Rod AW Rod 8 40 25-50 420 100-550 85 8.92 3/8 VectorDrill MS 2-7/8 to 3-1/4 BW Rod BW Rod 8 75 20-50 770 100-700 115 152 7/8 VectorDrill MS 3-1/4 to 4-1/8 2-3/8 Reg 2-3/8 Reg 8.8 120 20 - 80 340 100-450 165 143 3/4 VectorDrill MS 4-1/8 to 5-1/2 2-7/8 Reg 2-3/8 Reg* 18.2 400 80-160 415 90-220 770 324 3/4 VectorDrill MS 5 3/4 to 7-7/8 3-1/2 IF 3-1/2 Reg 17.8 650 100-250 450 75-235 1190 534 3/4 VectorDrill LS 5 3/4 to 7-7/8 3-1/2 IF 3-1/2 Reg 18 3 650 100-250 400 60-140 1850 57
( ) ( )
4 3/4 VectorDrill LS 5 3/4 to 7 7/8 3 1/2 IF 3 1/2 Reg 18.3 650 100 250 400 60 140 1850 575 1/2 VectorDrill MS 6-3/4 to 8 3/4 4-1/2 Reg 4-1/2 Reg 20.6 1050 150-300 450 70-170 1850 606 3/4 VectorDrill MS 8-3/8 to 9-7/8 4-1/2 IF 4-1/2 Reg 24 1875 300-600 645 80-295 3300 1856 3/4 VectorDrill LS 8-3/8 to 9-7/8 4-1/2 IF 4-1/2 Reg 23 1800 300-600 500 86-172 3830 125
8 VectorDrill LS 9-1/2 to 12-1/4 6-5/8 Reg 6-5/8 Reg 24.8 2725 300-800 425 50-180 4380 1509 5/8 VectorDrill MS 11-1/4 to 26 7-5/8 Reg 7-5/8 Reg 27 4325 500-1200 735 90-270 7680 3959 5/8 VectorDrill LS 11-1/4 to 26 7-5/8 Reg 7-5/8 Reg 27 4645 600-1200 455 67-134 8500 217
NOMENCLATURE : LS = Low Speed : MS = Medium Speed.TYPE AND APPLICATION : motors are PDM, high torque, low and medium speed for rock bit, PDC bit, slick or steerable system use.TEMPERATURE RATINGS : standard motors are rated to 240 deg F. High temperature motors are available for applications at 240-325 deg. F.BENT HOUSING : all motors are available with fixed bent housing or adjustable bent housing with 0 - 3 degree setting.
9 5/8 VectorDrill LS 11 1/4 to 26 7 5/8 Reg 7 5/8 Reg 27 4645 600 1200 455 67 134 8500 21711 1/4 VectorDrill LS 14-3/4 to 36 7-5/8 Reg 7-5/8 Reg 30.4 6650 1000-1500 450 80-145 11200 310
g j g g gSTABILIZERS : 6-3/4" - 11-1/4" motors can be supplied either slick or nearbit stabilizer sleeve.FLEXIBILITY : 9-5/8" motors can be run in hole sizes from top hole through 17-1/2" and 12-1/4" hole sections.OWNERSHIP AND MANUFACTURER : motors are owned and maintained by Target Well Control
Technology for Well Placement
Performance Vector-Drill Specifications
(ft-lbs)(rpm)(lbsx1000)(lbsx1000) (psi)(rpg)(gpm)Distance(Ft)(Bit sub)(Top sub)(inch)(inch)
(hp)TorqueRangeOverpullWOBDiff. Pres.gallonRangeStagesConfig.(lbs)to BendLengthConnectionConnectionBit Size:Diameter
PowerMax.Bit SpeedMaximum MaximumMax. MotorRevs perFlow RateNo ofLobeWeightBit BoxOverallThread Thread Recomm.Nomenclature:Outside
Operating Data:Physical Dimensions:Motor Type:
(ft-lbs)(rpm)(lbsx1000)(lbsx1000) (psi)(rpg)(gpm)Distance(Ft)(Bit sub)(Top sub)(inch)(inch)
(hp)TorqueRangeOverpullWOBDiff. Pres.gallonRangeStagesConfig.(lbs)to BendLengthConnectionConnectionBit Size:Diameter
PowerMax.Bit SpeedMaximum MaximumMax. MotorRevs perFlow RateNo ofLobeWeightBit BoxOverallThread Thread Recomm.Nomenclature:Outside
Operating Data:Physical Dimensions:Motor Type:
48263045 - 120110235000.48100 - 2503.87 x 886561.823.53-1/2' reg.3-1/2" IF5-3/4 to 7-7/8Vector Drill LS-XL4-3/4"
65210070 - 235110237700.94100 - 2506.54 x 586561.823.73-1/2' reg.3-1/2" IF5-3/4 to 7-7/8Vector Drill MS-XL4-3/4"
3550060 - 400827925520 - 805.24 x 518035.213.42-3/8" Reg.2-3/8" Reg.3-1/4 to 4-1/8Vector Drill MS-XL2-7/8"
(Inch)(Box)(Box)
48263045 - 120110235000.48100 - 2503.87 x 886561.823.53-1/2' reg.3-1/2" IF5-3/4 to 7-7/8Vector Drill LS-XL4-3/4"
65210070 - 235110237700.94100 - 2506.54 x 586561.823.73-1/2' reg.3-1/2" IF5-3/4 to 7-7/8Vector Drill MS-XL4-3/4"
3550060 - 400827925520 - 805.24 x 518035.213.42-3/8" Reg.2-3/8" Reg.3-1/4 to 4-1/8Vector Drill MS-XL2-7/8"
(Inch)(Box)(Box)
2836000124 - 248200556500.31400 - 80055 x 622909125.14-1/2" Reg.4-1/2" IF8-1/2 to 10-1/2Vector Drill MS-XL7-1/4"
185670060 - 145150556750.24300 - 60057 x 8228585.1264-1/2" Reg.4-1/2" IF8-3/8 to 9-7/8Vector Drill LS-XL6-3/4"
2505100100 - 255150558450.42300 - 60064 x 5229085.129.34-1/2" Reg.4-1/2" IF8-3/8 to 9-7/8Vector Drill MS-XL6-3/4"
1062125105 -262110256500.87100 - 30064 x 510606024.23-1/2' reg.3-1/2" IF6 to 7-7/8Vector Drill MS-XL5"
2836000124 - 248200556500.31400 - 80055 x 622909125.14-1/2" Reg.4-1/2" IF8-1/2 to 10-1/2Vector Drill MS-XL7-1/4"
185670060 - 145150556750.24300 - 60057 x 8228585.1264-1/2" Reg.4-1/2" IF8-3/8 to 9-7/8Vector Drill LS-XL6-3/4"
2505100100 - 255150558450.42300 - 60064 x 5229085.129.34-1/2" Reg.4-1/2" IF8-3/8 to 9-7/8Vector Drill MS-XL6-3/4"
1062125105 -262110256500.87100 - 30064 x 510606024.23-1/2' reg.3-1/2" IF6 to 7-7/8Vector Drill MS-XL5"
4862600066-14055625114800.12600 - 12006.57 x 853509031.37-5/8" Reg.7-5/8" Reg.11-1/4 to 26Vector Drill SST9-5/8"
3802000068 - 1445562519000.12600 - 12005.77 x 853509031.37-5/8" Reg.7-5/8" Reg.11-1/4 to 26Vector Drill ST9-5/8"
2831330050 - 150590978000.13600 - 120056 x 7520010030.87-5/8" Reg.7-5/8" Reg.11-1/4 to 27Vector Drill LS-XL9-5/8"
3281300068 -131590976000.11600 - 120045 x 65250121.734.37-5/8" Reg.7-5/8" Reg.11-1/4 to 27Vector Drill LS-XL9-5/8"
4862600066-14055625114800.12600 - 12006.57 x 853509031.37-5/8" Reg.7-5/8" Reg.11-1/4 to 26Vector Drill SST9-5/8"
3802000068 - 1445562519000.12600 - 12005.77 x 853509031.37-5/8" Reg.7-5/8" Reg.11-1/4 to 26Vector Drill ST9-5/8"
2831330050 - 150590978000.13600 - 120056 x 7520010030.87-5/8" Reg.7-5/8" Reg.11-1/4 to 27Vector Drill LS-XL9-5/8"
3281300068 -131590976000.11600 - 120045 x 65250121.734.37-5/8" Reg.7-5/8" Reg.11-1/4 to 27Vector Drill LS-XL9-5/8"
NOMENCLATURE : LS = Low Speed : MS = Medium Speed : ‘Plus’ = Extended Length Power Section : ‘Plus 2’ = Tandem Power Section.TYPE AND APPLICATION : motors are PDM, high torque, low and medium speed for rock bit, PDC bit, slick or steerable system use.TEMPERATURE RATINGS : standard motors are rated to 240 deg F. High temperature motors are available for applications at 240-325 deg. F.
3101120080 - 1459751124500.11000 - 15003.63 x 46650114.730.47-5/8" Reg.7-5/8" Reg.14-3/4 to 36Vector Drill LS11-1/4"
51832,27568-12455625115800.1600 - 12003.56 x 753509031.37-5/8" Reg.7-5/8" Reg.11-1/4 to 26Vector Drill ERT9 5/8"
3101120080 - 1459751124500.11000 - 15003.63 x 46650114.730.47-5/8" Reg.7-5/8" Reg.14-3/4 to 36Vector Drill LS11-1/4"
51832,27568-12455625115800.1600 - 12003.56 x 753509031.37-5/8" Reg.7-5/8" Reg.11-1/4 to 26Vector Drill ERT9 5/8"
Technology for Well Placement
BENT HOUSING : all motors are available with fixed bent housing or adjustable bent housing with 0 - 3 degree setting.STABILIZERS : 6-3/4" - 11-1/4" motors can be supplied either slick or nearbit stabilizer sleeve.FLEXIBILITY : 9-5/8" motors can be run in hole sizes from top hole through 17-1/2" and 12-1/4" hole sections.OWNERSHIP AND MANUFACTURER : motors are owned and maintained by Target Well Control
Performance Vector-Drill Specifications
VectorDrill PDMDIRECTIONAL DRILLING SYSTEMS
7 1/4" VectorDrill MS XL ( 5/6 - 5 Stage )DOWNHOLE MOTORS
Tool Dimensions & Performance Power Section
High Length 25.1 ft 7.65 m
U.S. Equivalent Units Metric UnitsTool Dimensions & Performance
Hole Sizes 8 1/2 - 10 1/2"Torque 6000 ft-lbs
Rotor
StatorPerformance Drilling
215.9 to 266.7 mmWeight 2290 lbs 1038 KgRecommended Bit Size 8 1/2 to 10 1/2 inFlow Rate - Standard Range 400 to 800 gpm 1514 to 3028 lpmMaximum Motor Diff Pressure 850 psi 58 barBit Speed 124 to 248 rpm 124 to 248 rpmTorque 6000 ft-lbs 8135 NmPower 283 Hp 211 KwMaximum Overpull 200000 lbs 100000 Kg q
Speed Range 124-248 rpm
Bent Housing
(0 to 3 deg)
CouplingPerformance Curve7 1/4" MS XL VectorDrill (Medium Speed)
300
) bs)6250250
7500
800 gpm
p g
Stabiliser(or slick)
Housing
Sleeve
Bearing200
150
100
50
00 100 200 300 400 500 600
01250
Spee
d (r
pm)
Torq
ue (f
t-l
Rated Pressure
3750
5000600 gpm
2500400 gpm
700 800 900 1000
800 gpm
Technology for Well Placement
0 100 200 300 400 500 600Motor Differential Pressure (psi)
700 800 900 1000
Performance Vector-Drill Specifications
VectorDrill PDMDIRECTIONAL DRILLING SYSTEMS
9 5/8" VectorDrill ST ( 7/8 - 5.7 Stage )DOWNHOLE MOTORS
Length 31.3 ft 9.54 mWeight 5350 lbs 2427 Kg
U.S. Equivalent Units Metric UnitsTool Dimensions & Performance Power Section
Rotor
High PerformanceRecommended Bit Size 11 1/4 to 26 in
Flow Rate - Standard Range 600 to 1200 gpm 2271 to 4542 lpmMaximum Motor Diff Pressure 900 psi 62 barBit Speed 68 to 144 rpm 68 to 144 rpmTorque 20000 ft-lbs 27116 NmPower 380 Hp 283 KwMaximum Overpull 556000 lbs 278000 Kg
285.8 to 660.4 mm
Hole Sizes 11 1/4 - 26"Torque 20000 ft-lbsS d R 68 144
Rotor
StatorPerformance Drilling
Speed Range 68-144 rpm
Straight Housing
(Bent optional)
Coupling
B i
Performance Curve9 5/8" ST VectorDrill
150
100m) -lb
s)18000125
22000
1200 gpm Stabiliser(or slick)
Housing
Sleeve
Bearing100
75
50
25
00 100 200 300 400 500 600
02000
Spee
d (r
pm
Torq
ue (f
t-
Rated Pressure
10000
14000900 gpm
6000600 gpm
700 800 900 1000
Technology for Well Placement
0 100 200 300 400 500 600Motor Differential Pressure (psi)
700 800 900
Performance Vector-Drill Specifications
Technology for Well Placement
Performance Vector-Drill Specifications
• Even Rubber Thickness Type
• Operating Torque 32,275 Ft-Lb
• Stalling Torque 54,000 Ft-Lb
• Max Differential Pressure 1,300 PSI
• HP 518hp
Technology for Well Placement
Performance Vector-Drill Specifications
VectorDrill PDMDIRECTIONAL DRILLING SYSTEMS
11 1/4 inch VectorDrill LSDOWNHOLE MOTORS
Length 30.4 ft 9.3 mWeight 6650 lbs 3020 Kg
Tool Dimensions & Performance U.S. Equivalent Units Metric Units Power Section
Rotor
High Performance
Recommended Bit Size 14 3/4 to 36 in 374.7 to 914.4 mmFlow Rate - Standard Range 1000 to 1500 gpm 3785 to 5675 lpmMaximum Motor Diff Pressure 450 psi 31 barBit Speed 80 to 145 rpm 80 to 145 rpmTorque 11200 ft-lbs 15200 NmPower 310 Hp 230 Kw
Maximum Overpull 975,000 lbs 440,000 kg
Hole Sizes 14 3/4 - 36"Torque 11200 ft-lbsSpeed Range 80 - 145 rpm
Rotor
StatorDrilling
Bent Housing
(0 to 3 deg)
Coupling
Bearing
Performance Curve11-1/4" VectorDrill
200
150m) -lb
s)9000
10500175
12000
1500gpm
Stabiliser
Housing
Sleeve
Bearing150
125
100
75
00 50 100 150 200 250 300
0
ff ( )
4000
Spee
d (r
pm
Torq
ue (f
t-
Rated Pressure
7500
90001250gpm
60001000gpm
350 400 450 500
Technology for Well Placement
Motor Differential Pressure (psi)
MWD / LWD Services
MWD / LWD S iMWD / LWD Services
Technology for Well Placement
Geo-Steering
• Replace Wireline Logging in High Angle / HorizontalReplace Wireline Logging in High Angle / Horizontal Wells
• Geo-Steering - Dipping Bed Modeling
• Oil / Water Contact Identification
• Determination of Optimum Perforation ZonesDetermination of Optimum Perforation Zones
Technology for Well Placement
Geo-Steering – Dipping Bed Modeling
Technology for Well Placement
Geo-steering – Dipping Bed Modeling
Technology for Well Placement
Standard Directional MWD Service
Service Benefits
• Provides reliable directional MWD measurements in hole sizes down to 5⅞” diameter (9½” - 4¾” collar sizes)Provides reliable directional MWD measurements in hole sizes down to 5⅞ diameter. (9½ 4¾ collar sizes)• Transmits: Hole inclination, Azimuth, tool face & circulating temperature (tool also transmits a QA status word with each
transmission)• Tool modes can be programmed from surface• Continuous tool faces in steering mode• Survey transmission time: Average 90 seconds• Tool face update rate: Average 30 seconds
Average 9 seconds in fast mode• Power Source: High temperature lithium battery
Operating Parameters Directional Sensor Specifications
M i Fl t b C ll Si AMaximum Flow rates by Collar Size: Accuracy9½” OD: 1200 gpm Inclination: ± 0.1°8” OD: 900 gpm Azimuth: ± 0.5° (inc > 5°)6¾” OD: 700 gpm Magnetic Tool Face ± 1.0°4¾” OD: 350 gpm Gravity Tool Face : ± 0.5°No lower flow limit Temperature: ± 0.5°CNominal pressure drop* RepeatabilityNominal pressure drop Repeatability(Dependent on mud weight & flow rate) Inclination: ± 0.05°
Azimuth: ± 0.5°Maximum sand content: 1% by volume** Crossover to highside tool face at inclinations > 3.0°Maximum operating temperature: 302°FMaximum operating pressure: 15000 psi (20,000 psi available)Maximum drill String RPM: No limit
Technology for Well Placement
LCM circulation limits: No limit **** Refer to Target’s pressure drop charts** No uphole filter required*** LCM pills may inhibit tool operations
Directional Gamma LWD Service
Service Benefits
• Gamma module is compatible with all Target’s MWD systems down to 3⅛” ODGamma module is compatible with all Target s MWD systems down to 3⅛ OD• Rapid service upgrade at the wellsite without deploying extra complete downhole assemblies• Self contained module with its own power source ensures Directional MWD reliability is not compromised• Does not increase the length of the BHA because of sonde configuration• Gamma measurement is close to the bit, particularly if used with Targets • Enhanced Survey Accuracy (ESA) service option
Gamma Sensor Specifications
• Photomultiplier tube with 4” x 1¼” scintillation detector
Service Specifications
• Gamma update rate: Average 60 seconds• Gamma memory sampling: 16 second samples
Gamma BatteryCartridge
PGamma memory sampling: 16 second samples• Gamma memory life: 200 hours• Directional Survey transmission time: As per standard directional MWD service
Operating Parameters and Physical Specifications
Processor
High VoltageAssembly
Gamma Detector
Technology for Well Placement
As per Directional MWD ServiceGamma Detector
PWR (Propagation Wave Resistivity) LWD Service
Service Benefits
• Available in 4¾” 6¾” 7¾” and 8¼” OD tool diameters• Available in 4¾ , 6¾ , 7¾ and 8¼ OD tool diameters• Unique patented wellsite calibrator• Sonde configuration electronics for flexibility and reliability• 1 Mhz transmitter frequency provides industry leading depth of investigation• Dual transmitter borehole compensation design enhances accuracy and reliability
Sensor Specifications
PWR Sub Assembly Length: 10 ft 4” (3.14m)Power Source: High temperature lithium batteryMaximum Operating Temperature: 150°CMeasurement Range: 0.2 to 2000 ohm-metersMeasurement Technique: 1.0 Mhz dual transmitter dual receiver compensated phaseAccuracy Phase Difference: ± 2% 0.2 - 20 ohm-metres
± 5% 20 - 50 ohm-metres± 10% 50 - 200 ohm metres± 20% 200 - 500 ohm-metresReduced Accuracy 500 - 2000 ohm-metres
Repeatability: ± 1% of readingVertical Resolution: Nominal 12”. 6” with deconvolution processingCorrections: Tool size, borehole diameter and mud resistivityCalibration: Field calibration fixture, air hang, saline tankMemory: 2Mb of non-volatile memory
Technology for Well Placement
Memory: 2Mb of non volatile memoryLog enhancement and modeling: Deconvolution, Response modeling software,
Dipping Bed model, Field and tank calibration
PWR/PDD (Propagation Wave Resistivity / Pressure During Drilling) MWD / LWD Service
Service BenefitsService Benefits
• Available in 4¾”, 6¾”, 7¾” and 8¼” OD tool diameters• Unique patented wellsite calibrator• Sonde configuration electronics for flexibility and reliability• 1 Mhz transmitter frequency provides industry leading depth of investigation
D l t itt b h l ti d i h d li bilit• Dual transmitter borehole compensation design enhances accuracy and reliability
PWR Sensor Specifications
PWR/PDD Sub Assembly Length: 22ft (Including Battery Sub)Power Source: High Temperature Lithium BatteryMaximum Operating Temperature: 150°CMeasurement Range: 0.2 to 2000 ohm-metersMeasurement Technique: 1.0 Mhz dual transmitter dual receiver compensated phaseAccuracy Phase Difference: ± 2% 0.2 - 20 ohm-metres
± 5% 20 - 50 ohm-metres± 10% 50 - 200 ohm metres± 20% 200 - 500 ohm-metresReduced Accuracy 500 - 2000 ohm-metres
Repeatability: ± 1% of readingVertical Resolution: Nominal 12 inches, 6 inches with deconvolution processing.Corrections: Tool size, Borehole diameter and mud resistivity
Technology for Well Placement
, yCalibration: Field Calibration Fixture, Air Hang, Saline Tank.Memory: 2Mb of non-volatile memory
PWR/PDD (Propagation Wave Resistivity / Pressure During Drilling) MWD / LWD Service
(continued)
PDD Sensor Specifications
Measurement Range: 0 - 15000 psiAccuracy: ± 0.25% of full scaleRepeatability: ± 3 psiTransmitted Resolution 3.662 psi / bitpOperating Temperature Range: -55°C to 150°CMeasurement Type: Keller Piezo Resistive Silicon SensorDetection Method: Phase sensitive detector / Synchronous demodulatorCorrections: 4th order temperature correction of bias and scale factorAveraging Time: Adjustable from 1sec - 30secUpdate Time Adjustable from 1sec - 30secUpdate Time Adjustable from 1sec 30secMemory: 1Mb of non-volatile memoryPower Source: High temperature lithium battery Battery Life 300 hours
Technology for Well Placement
3⅛”x 3½” PDD (Pressure During Drilling) “Real-time” & Memory MWD / LWD Service
S i B fitService Benefits
• Available in 3⅛”, 3½”, 4¾”, 6¾”, 7¾” and 8¼” OD tool diameters
Sensor Specifications Service Applications
Measurement Range: 0 - 15000 psiAccuracy: ± 0.25% of full scaleRepeatability: ± 3 psiTransmitted Resolution 3.662 psi / bitOperating Temperature Range: -55°C to 150°C
Service Applications
• Real-time downhole hydraulics monitor• Real-time ECD monitoring and management• Annulus cuttings overload detection• Washout detection• Kick monitoring and controlp g p g
Measurement Type: Keller Piezo Resistive Silicon SensorDetection Method: Phase sensitive detector /
Synchronous demodulatorBridge Excitation: ACCorrections: 4th order temperature correction
of bias and scale factor
• Kick monitoring and control• Lost circulation detection• Mud motor performance and control• Mud rheology control• Optimisation of hole cleaning• Formation fracturing / loss limitation
Ai d d b l d d illi ll t lof bias and scale factorAveraging Time: Adjustable from 1sec - 30secUpdate Time Adjustable from 1sec - 30secMemory: 1Mb of non-volatile memoryPower Source: High Temperature Lithium Battery Battery Life 300 hours
• Air and underbalanced drilling well control• Nitrogen / Air mix control
Technology for Well Placement
3⅛”x 3½” MWD - Slim Hole MWD Service
Service Benefits
• Provides reliable directional and gamma MWD measurements in hole sizes down to 4” diameter• Provides reliable directional and gamma MWD measurements in hole sizes down to 4 diameter• Provides another contingency hole size below the current 6” diameter• Makes drilling horizontal drains out of existing wells with liners or completions down to less than 4” diameter feasible• Modular heli-portable design facilitates use in remote locations and logistics in inaccessible locations• Maximum build rates of 1.0° per foot (non rotating)
Directional Sensor and Service Specifications
• As per Standard Directional MWD Service
O ti P t Ph i l S ifi tiOperating Parameters Physical Specifications
Maximum flow rate: 160 GPM Hole Sizes: 4” - 4⅛”No lower flow limit. Transmitter OD: 3⅛”Nominal pressure drop. * Collar ID: 3⅛” x 3½”(Dependent on mud weight & flow rate) Collar ID: 2½”Maximum build rate: 1°/1ft Connections: As per customer requestMaximum sand content: 1% by volume ** Total Length (Dir only): 27 ftMaximum operating temperature: 300°F Total Length (Dir & Gamma): 27 ftMaximum operating pressure: 20,000 psiMaximum drillstring RPM: No limitLCM circulation limits: No limit ***
Technology for Well Placement
* Refer to Target’s pressure drop chart** No uphole filter required*** LCM pills may inhibit tool operations
3⅛” x 3½” PWR (Propagation Wave Resistivity) MWD Service
Service Benefits• Dual transmitter borehole compensation design enhances accuracy and reliability• Dual transmitter borehole compensation design enhances accuracy and reliability• Unique patented internal antenna design• Sonde configuration electronics for flexibility and reliability• 1 Mhz transmitter frequency provides industry leading depth of investigation
Operating ParametersM i Fl t 160Maximum Flowrate: 160 gpmMaximum Operating Temperature: 150°CMaximum Operating Pressure: 20,000 psiMaximum build rate: 25°/100 ft
Sensor SpecificationsPWR Sub Assembly Length: 12 ft 2” (3.70 meters)Power Source: High temperature lithium battery or mud turbineMeasurement Range: 0.2 to 2000 ohm metersMeasurement Technique: 1.0 Mhz dual transmitter dual receiver compensated phaseAccuracy Phase Difference: ± 2% 0.2 - 20 ohm-meters
± 5% 20 - 50 ohm-meters± 10% 50 - 200 ohm-meters± 20% 200 - 500 ohm-metersReduced Accuracy 500 - 2000 ohm-meters
Repeatability: ± 1% of readingVertical Resolution: Nominal 12”. 6” with deconvolution processingCorrections: Tool size, borehole diameter and mud resistivity
Technology for Well Placement
Corrections: Tool size, borehole diameter and mud resistivityMemory: 2Mb of non-volatile memory
PWR Downhole Electronics for PWR Subs Sizes 8¼” to 4¾”
Clamp Bolt: C.B.
3½” IF
F'Thru Bolt: F.B.
C.B.F.B.Transmitter
(U )
Upper Tx.
CPU/M
C.B.F.B.Receiver
(Upper)
(Upper)CPU/Mem.
Local OSC.
Upper Rx.
F'Thru
F.B.C.B.
C.B.
(Upper)
Receiver(Lower)Lower Rx.
A-D/DSP.F ThruMemoryDump PortF.B.C.B.
Transmitter(Lower)
PSU.
Lower Tx.
Technology for Well Placement
3½” IF
PWR Downhole Electronics For PWR SubsSizes 8¼” to 4¾”
3.25 ft
Clamp Bolt: C.B.F'Thru Bolt: F.B.
3½” IF
2.30 ft
C.B.
F.B.
C B
Transmitter(Upper)
10.14 ft
0.98 ft
C.B.
F.B.
F.B.
C.B.
Receiver(Upper)
Receiver(Lower)
2.30 ft
F'ThruMemoryDump Port
C.B.
F.B.
C.B.
Transmitter(Lower)
Technology for Well Placement
1.31 ft
PWR 1MHz Advantages
• Depth of InvestigationDeeper than 2.0 MHz systems
Rt 1 0 MH S t 2 0 MH S tRt 1.0 MHz System 2.0 MHz SystemPh Ar Ph Ar
20.0 69.3 133.4 60.6 99.4
1 0 39 0 60 6 32 4 51 0
• Sensitivity of BoreholeDeeper depth of investigation results in less sensitivity to borehole effects
• Vertical Resolution
1.0 39.0 60.6 32.4 51.0
Vertical resolution is smaller than 2 MHz systems but acceptable• Dielectric Constant
1 MHz system less sensitive; generally dielectric effect is negligible compared to 2 MHz systemy
• Dynamic RangeThe frequency and spacings result in a wider dynamic ranger providing better phase resolution over the resistivity range of interest
Technology for Well PlacementTGT 00001
EMTEL MWD Electro-Magnetic MWD Service
Service Benefits
• Provides reliable MWD/LWD measurements in hole sizes down to 5⅞” diameter (9½” - 4¾” collar sizes)• Data transmission independent of rig hydraulic system• System operates in underbalance, air/multi-phase fluid systems• Compatible with all Target’s existing MWD/LWD sensors: directional, vibration, gamma, resistivity and
pressure
Operating Parameters
Operating Frequency: 5HzMaximum Flow rates by Collar Size: 9½” OD: 1200 GPMy
8” OD: 900 GPM6¾” OD: 700 GPM4¾” OD: 480 GPMNo lower flow limit
Power Source: High temperature lithium battery (200 Hours)Maximum sand content: 0.5% by volumeMaximum operating temperature: 302°FMaximum operating pressure: 15,000 psi (20,000 psi available)Maximum drill String RPM: No limitLCM circulation limits: No limit
Technology for Well Placement
Positive Pulse Retrievable MWD Service
Service Benefits
• Provides reliable MWD/LWD measurements in hole sizes down to 3¾” diameter (9½” 3⅛” collar sizes)• Provides reliable MWD/LWD measurements in hole sizes down to 3¾ diameter. (9½ - 3⅛ collar sizes)• Compatible with all Target’s existing MWD/LWD sensors: directional, vibration, gamma, resistivity and
pressure• MWD electronics (directional and gamma) are retrievable in the event the BHA becomes stuck, reducing
LIH cost exposure.
Operating Parameters
Maximum Flow rates by Collar Size: 9½” OD: 1200 gpm8” OD: 900 gpm6⅛” OD 7006⅛” OD: 700 gpm4⅛” OD: 480 gpm3½” OD: 160 gpm3⅛” OD: 120 gpmNo lower flow limit
Power Source: High temperature lithium battery (250 hrs)Power Source: High temperature lithium battery (250 hrs)Maximum sand content: 0.5% by volumeMaximum operating temperature: 302°FMaximum operating pressure: 15,000 psi (20,000 psi available)Maximum drill String RPM: No limitLCM circulation limits: 40 lbs/bbl
Technology for Well Placement
Electronic Magnetic Multi-Shot (EMMS)
The Champ 150 Tool incorporates the latest technology and software programs in magnetic and gravity sensors, calibration and modeling to provide an accurate, all angle, solid state electronic magnetic surveying tool.g , g y g
Solid State Electronics• Downhole electronic recording • Non-volatile memory and data retention • Thermal modeling assures accurate calibration over the entire temperature range
Operating Features• Options for single-shot or multi-shot operation • Variable delay time 5 to 32 00 sec• Variable delay time 5 to 32,00 sec • Operates to +150°C (+302°F) • Self-contained, battery powered. Operational life depends upon selected intervals and averaging. • Proven survey accuracy: lateral displacement accuracy 1.7ft. per 1,000 typical
Operating Specificationsp g p• Probe length: 1.38” diameter x 42” long• Weight: 5.0 lbs• Power Pack: 1.38” diameter x 29” long, weight 4.5 lbs• Storage: -20°C to +150°C without batteries • Pressure Barrell: 12,00 psi, 1.75 in. O.D.
Technology for Well Placement
• Inclination: reads to 0.1°• Tool Face: reads to 0.25°
Developments and New Technology
Developments and New Developments and New Technology
Technology for Well PlacementSlide 43 RST Introduction
New Technology
Short Radius RST • Target Well Control has acquired the design know how UBHO
“Scribe Line”
• Target Well Control has acquired the design, know-how and prototype tools for a cost effective, short radius rotary steerable drilling system from Calgary based Tesco Corporation. The acquisition has been accompanied by the transfer of a patent license from BP
UBHO
Corporation North America Inc that allows Target to market this technology on a world-wide basis.
• ‘Point-the-bit’ technology for high rates of curvature
MWD
• Prototype tools built for 3 7/8”, 4 ½” and 6” hole sections.
• Ideally suited to short-radius curves (e.g. sidetracked laterals off an existing wellbore). Consistent curvature
DeflectionSleeve
produced. 4 ½” hole drilled with radius of curvatures in the range of 30 ft to 97 ft produced (190° to 59°/100 ft). After building to horizontal the rotary steerable assembly is pulled out and a tangent assembly run. M ffi i t th d illi ti ll ith PDM’
Drill Bit
Technology for Well Placement
• More efficient than drilling conventionally with PDM’s. Time saved by removing problems relating to sliding and more aggressive PDC bits can be utilised.
R =L2
2e
•Bit drills where pointed•No lateral loads from drillstring imparted to bit•Radius of curvature controlled by:
C t t i t bit
2
- Contact point on bit- Contact point near flexible joint- Bit axis aligned with hole axis at bit face
•Critical –
13 Bit must drill gauge hole
Joint contact must be stable and controlledJoint contact must not cut into hole wall
++ e
Technology for Well Placement
20033--77//88” Assembly” Assembly
RADIUS OF CURVATURE (FT)
125
150
175 1010..2525” mandrel length” mandrel length77..312312” bit length” bit length
100
Theoretical(e = 0.276”)
75
0
25
0 5 10 15
South Texas
Canada50
0 5 10 15
Length of Sub Used with Assembly (in)
Technology for Well Placement
Dogleg Capability versus Sub Length
DLS Radius of Curvature
Overall Length (L) Between Contact
Points
Sub Length Required
(°/100 ft) (ft) (ft) (in)
10 573 5.1 46
20 286 3.6 28
30 191 3.0 20
40 143 2.6 16
50 115 2.3 12
60 95 2.1 10
70 82 1.9 8
80 72 1.8 7
90 64 1.7 5
100 57 1.6 4
Technology for Well Placement
The relationship between DLS and radius of curvature can be determined by the following formula:
length units feet, DLS °/100 ft length units metres, DLS °/30m
R = 360 x 100 R = 360 x 302 π DLS 2 π DLS
ftherefore:DLS = 360 x 100 DLS = 360 x 30
2 π R 2 π R
where: R = radius of curvatureDLS = dogleg severity
Technology for Well Placement
Technology for Well Placement
New Technology
Short Radius Rotary Steerable SystemDevelopment Status
• Prototype tools built & tested for 3 7/8”, 4 ½” and 6” hole sections • Redesign including PDM power section• Facilitate multi-mode operation (curve & tangent)
R d i / N M ti M t i l• Redesign w/ Non Magnetic Material• Real Time sleeve orientation w TF Updates• Integrate TF measurement into MWD• Near Bit Inc. integrated into MWD
Sh t H D H l C bilit
Signal Port
Latch
• Short Hop Down Hole Capability• Next generation tool available Q4 2008
DeflectionSleeve
Latch
Technology for Well Placement
Mandrel axis offset from hole axis
New Technology
Short Radius Rotary Steerable SystemDevelopment Status
• Prototype tools built & tested for 3 7/8” 4 ½” and 6” hole sections• Prototype tools built & tested for 3 7/8”, 4 ½” and 6” hole sections • Redesign including PDM power section• Facilitate multi-mode operation (curve & tangent)• Redesign w/ Non Magnetic Material• Real Time sleeve orientation with TF Updates• Integrate TF measurement into MWD• Near Bit Inc. integrated into MWD• Short Hop Down Hole Capability
Signal Port
Latch
DeflectionSleeve
Latch
Technology for Well Placement
Mandrel axis offset from hole axis
• Technology Under Development
– Smart Drilling Closed Loop RST/VDS – QUAD Combo LWD (In project feasibility study)– NMR LWD and interval transit time LWD capability– Short hop/well-bore communications system– Multi-frequency propagation wave resistivity (PWR) toolsq y p p g y ( )– Expand geosteering capabilities with new measurements in all
hole sizes
Technology for Well Placement
Operational Envelope
• Borehole Size: 5-7/8” to 6-1/8” adjustable by pad design• Build rate: 0 - 6.5 Degrees / 100ft• Temperature: 125 Deg.C / 150 Deg.C Option• Pressure: 10,000 PSI (600 Bar)• Tool OD: 4.5” Nominal, 4.75” at Transmitter Sub• Tool ID: 1.0” Nominal• Length: 17.7ft• Flow: 330 GPM• RPM: 60 - 120 RPM Rotary / 120 - 500 RPM Motor• Torque: 15,000 ft/lbs• WOB: 14,000 Operational - 22,000 lbs Maximum• Connections: 3-1/2” API NC38• Tensile yield: 217,700 lb
Technology for Well Placement
y ,
Slide 53Slide 53 RST Operational Envelope
Tool Pictures
Technology for Well PlacementSlide 54Slide 54 RST Views
Tool Pictures
Technology for Well PlacementSlide 55Slide 55 RST Views
Steering Geometry
4.5´´ RSS - Steering schematic A - A
resulting force=
steering directionA
WOBWOB
t i ft i fA
steering forcesteering force
Technology for Well PlacementSlide 56Slide 56 RST Steering
Technology Implementation
• Push the bit implementation (Similar to Autotrack)
• Proven Physics assured steering and control Proven Physics assured steering and control
• Non Rotating sleeve design
• Four pad piston design for steering control
• Complete 3D steering controlComplete 3D steering control
• Accurate downhole closed loop implementation
• 3 Axis accelerometer / magnetometer close to bit
Technology for Well PlacementSlide 57Slide 57 RST Technology Implementation
Operational Envelope
• Borehole Size: 5-7/8” to 6-1/8” adjustable by pad design• Build rate: 0 - 6.5 Degrees / 100ft• Temperature: 125 Deg.C / 150 Deg.C Option• Pressure: 10,000 PSI (700 Bar)• Tool OD: 4.5” Nominal, 4.75” at Transmitter Sub• Tool ID: 1.0” Nominal• Length: 15ft• Flow: 350 GPM• RPM: 60 - 120 RPM Rotary / 120 - 500 RPM Motor• Torque: 12,000 ft/lbs• WOB: 26,500 lbs• Connections: 3-1/2” API NC38
Technology for Well PlacementSlide 58Slide 58 RST Operational Envelope
MWD Nuclear Magnetic Resonance
• Target in conjunction with Aberdeen University have received DTI funding for an alternate to conventional Triple Combo LWDfunding for an alternate to conventional Triple Combo LWD
• Will provide the company with state-of-the-art Porosity, Permeability and Free- Fluid- Index measurements
Technology for Well Placement
Multiple Frequency Resistivity
• State of the Art Multiple Depth of investigation resistivityp p g y
• Advanced Geosteering
• RXO / Invasion profiling
• Enhanced precision and accuracy
Technology for Well Placement