mechanical catalog 2013 - grinnell.hu - grinnell hornyos ... · 125 139.7 51.7 79.26 4.8 178.3...

GROOVED

COUPLINGS

17

www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings

GRINNELL reserves the right to change the contents without notice.18

GRINNELL Couplings are designed for grooved end pipe and are available in nominal sizes of 25 to 600mm (1" to 24") including BS, ISO, and JIS outside diameters.

The GRINNELL Coupling Design provides economical advantages when compared to welded or flanged systems. GRINNELL Couplings provide a universal method for connecting pipe, fittings, and pipe system components.

GRINNELL Couplings and Gaskets permit a wide selection of combinations for specific applications.

Field modifications are easily accommodated with GRINNELL Mechanical Products as the couplings can be easily rotated, eliminated and/or added to facilitate necessary modifications.

Grooved Couplings Table of Contents

General notes: Additional information is included in our data sheets and is available upon request. It is the Designer’s responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data is not exceeded. Always read and understand the installation constructions. Never remove any piping components nor correct or modify any piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified with the gasket recommendation listing for the specific application.

Figure 772

Rigid Couplings

Pages 20 - 21

Figure 740

Rapid Installation Pivot-Bolt (GRIP) Rigid Couplings

2

Figure 774

Rigid Couplings

Page 23

Figure 705

Flexible Couplings

Page 24

Figure 770

High Pressure Rigid Couplings

Page 25

Figure 707

Heavy Duty Flexible Couplings

Pages 26 - 27

Figure 707L

Large Diameter Couplings

Page 28

Figure 7707 N

Large Diameter Flexible Couplings

Page 29

Figure 909

Plain End Couplings

Page 30

Figure 780

Grooved Snap Couplings

Page 31

Figure XH-70EP

Extra Heavy Rigid Couplings With End Protection (EP) Gasket

Pages 32 & 171

Figure 716

Flexible Reducing Couplings

Page 33

Figure 702

Mechanical Outlet Couplings

Pages 34 - 35

Figure 7706-T

Transition Couplings

Page 36

Electrical Continuity

Page 37

Refer to back cover for country-specific contact information

GROOVED COUPLINGS

Grooved

Couplings

19

Full contact between Figure 772 Coupling key and groove diameter

Ductile Iron Housing Specifications

castings, Grade 65-45-12

(65,000 psi)

(45,000 psi)

galvanizing

Bolt/Nut Specifications

Metric: Carbon steel oval neck track head bolts (Gold colour coded) are heat treated and conform to the physical properties of ASTM F 568M with a minimum tensile strength of 760 MPa. Carbon Steel heavy hex nuts conform to the physical properties of ASTM A 563 M Class 9. Bolts and nuts are zinc-electroplated conforming to ASTM B 633.

ANSI: Carbon steel oval neck bolts and nuts are heat-treated and conform to the physical properties of ASTM A 183 Grade 2 and SAE J429 Grade 5 with a minimum tensile strength of 7584 Bar (110,000 psi). Carbon Steel heavy hex nuts conform to the physical properties of ASTM A 183 Grade 2 and SAE J995 Grade 5. Bolts and nuts are zinc-electroplated conforming to ASTM B 633.

request.

Coatings

GRINNELL Coupling Gasket Specifications

gaskets have a Green colour code stripe identification and conform to ASTM D 2000 for service temperatures from -34°C to 110°C ( -30°F to 230°F). They are recommended for hot water not to exceed 110°C (230°F), plus a variety of dilute acids, oil free air, and many chemical services. They are not recommended for petroleum services. For low temperature and vacuum systems, a Tri-Seal Grade “E” EPDM gasket with a rigid coupling is recommended.

gaskets have an Orange colour code stripe identification and conform to ASTM D 2000 for service temperatures from -29°C to 82°C ( -20°F to 180°F). They are recommended for petroleum products, vegetable oils, mineral oils, and air with oil vapors.

gaskets are Red colour code stripe and conform to ASTM D 2000 for service temperatures from -34°C to 177°C ( -30°F to 350°F). They are recommended for air without hydrocarbons, or dry heat.

gaskets have a Blue colour code stripe and conform to ASTM D 2000 for service temperatures from -7°C to 149°C (+20°F to 300°F). They are recommended for oxidizing acids, petroleum products, hydraulic fluids, lubricants, and halogenated hyrdrocarbons.

gaskets have a Yellow and Green colour code stripe and are for potable water systems up to 82°C (180°F). They are not recommended for petroleum service.

NSF-61 Certified centre-stop, push-on style gaskets have a Green and Red colour code stripe. For closed-loop heating systems from -34°C to 120°C (-30°F to 250°F) and potable water systems up to 82°C (up to 180°F). Recommended for use in low temperature and vacuum systems. They are not recommended for petroleum service.

MATERIAL SPECIFICATIONS

Additional Features:

special tools.

Limited Warranty, except for G-MINE which is 6 months. Review terms and conditions of sale on www.grinnell.com.

* Shurjoint product specifications can be found at www.shurjoint.com

www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings


Figure 772 Rigid Couplings(Page 1 of 2)

Tech Data Sheet: G141The GRINNELL Figure 772 Rigid Coupling provides a rigid joint by firmly gripping along the full 360° circumference of the pipe grooves. This coupling offers a dependable method of joining pipe and is an economical alternative to welding, threading, or using flanges. The GRINNELL Figure 772 Rigid Coupling is UL Listed for grounding and bonding, and is suitable for bonding systems with a maximum service entrance capacity of 200 amps. Sizes 32 – 200mm (1 1⁄4" – 8") feature a clamshell design that makes installation easier and faster.

��

Part Number Pipe SizeMax.†

PressureBar� � � Max.†

End LoadkNLbs.

Max.*‡ End Gap mmInches

Dimensions Coupling BoltsApprox.WeightKg.Lbs.

Grade “E” Gasket

Grade “E” Tri-Seal Gasket

Nominal mmInches

O.D.mmInches

AmmInches

BmmInches

CmmInches

Qty.SizemmInches

772ME0042 772MT004232 42.4 51.7 7.22 1.5 69.9 111.3 46.0

2M10 x 57 0.5� � � � � � � � ! � � " � # $ � � � � # � ! % � $ & � � & � ' ( ) # � � � � �

772ME0048 772MT004840 48.3 51.7 9.46 2.0 76.2 117.3 46.0

2M10 x 57 0.5� � * � � + � � ! � # " � # � � � & $ � � � % � � # � � & � ' ( ) # � � � � �

772ME0060 772MT006050 60.3 51.7 14.78 4.8 86.6 145.0 48

2M12 x 76 1.3# # � $ ! ! � $ " $ # $ � � � & & $ � % � ! � � � � + � * ) $ # � +

772ME0073 772MT007365 73.0 51.7 21.66 4.8 100.8 160.0 48

2M12 x 76 1.5# � * # � & ! ! � % " & � + � � � & & $ � + � � $ � � � + � * ) $ $ � $

772ME0076 772MT007665 76.1 51.7 23.58 4.8 104.1 163.0 48

2M12 x 76 1.6 � " � , , $ � � � � ! � ! " $ � � � � � & & % � � � � � % $ � � + - $ � �

772ME0089 772MT008980 88.9 51.7 32.10 4.8 116.8 176.0 48

2M12 x 76 1.7$ $ � ! � � ! � " # � � � � � & & % � � � � � + $ � � + � * ) $ $ �

772ME0114 772MT0114100 114.3 51.7 53.06 4.8 147.6 205.0 48

2M12 x 76 2.0% % � ! � � ! � � � " + # & � � � & & ! � & � & � � � � + � * ) $ % � $

772ME0139 772MT0139125 139.7 51.7 79.26 4.8 178.3 246.9 52.3

2M16 x 83 3.4� $ + " , , ! � ! � � ! � � " & � + � � � + � � # + � # # � � � - � !

772ME0141 772MT0141125 141.3 51.7 81.09 4.8 180.1 246.6 51.8

2M16 x 83 3.4! ! � ! � $ ! � � & " # # + � � � + � � + + � � # � � % . ( ) $ � � � !

772ME0165 772MT0165150 165.1 48.3 103.18 4.8 205.5 267.5 54.1

2M16 x 83 3.4� � ! " � , , � � ! � � � � # $ " # # & � � � + & � � + � � � ! $ # � � $ - � �

772ME0168 772MT0168150 168.3 48.3 107.34 4.8 205.5 267.5 54.1

2M16 x 83 3.4� � � � # ! � � # % " � $ � � � � + & � � + � � � ! $ # � � $ . ( ) $ � � � �

772ME0219 772MT0219200 219.1 41.4 155.94 4.8 268.2 344.4 66.5

2M20 x 121 8.2& & � � # ! � � � $ ! " � ! � � � � + � � � ! � � $ � ! � # � � # ' � ) % ' � � & � �

For detailed Listing / Approval information

contact GRINNELL Mechanical Products.

Issue 03, 04, 07

Cert No. 570, 669, 673


GROOVED COUPLINGS

Grooved

Couplings

21

Figure 772 Rigid Couplings(Page 2 of 2)

Tech Data Sheet: G141

/01 / 1 0 1/ 02 3 4 4 5 2 6 7 4 4 8 9 : ; < = 9 > < ? @ 7 7 4 4 5 @ 6 7 4 4 8 9 A < = 9 B < ? 6 7 7 4 4 5 C 7 7 4 4 8 D E < = D > < ?



End LoadkNLbs.


Dimensions Coupling BoltsApprox.WeightKg.Lbs.

Grade “E” Gasket


Nominal mmInches

O.D.mmInches

AmmInches

BmmInches

CmmInches

Qty.SizemmInches

772ME0273 772MT0273250 273.0 34.5 201.87 3.3 326.1 416.8 66.5

2– 11.2� � � � � ! � ! � � % ! " $ & � � � � $ � # � & % � � � % � # � � # � ) � � * # % � �

772ME0324 772MT0324300 323.9 27.6 227.17 3.3 391.4 478.5 66.5

2– 19.1� # � # � ! � % � � ! � " � � � � � $ � ! � % � � & � & % # � � # � ) � � * % # � �

772AE0355 772AE0355350 355.6 20.7 205.43 3.3 423.7 517.6 74.4

2– 21.7� % � % � � � � $ � � % � " � & � � � � $ � � � � & # � � $ & # � + $ � ) ! � * % & � �

772AE0406 772AE0406400 406.4 20.7 268.31 3.3 469.9 575.1 74.4

3– 23.6� � � � � � � � $ � � � � " $ � + � � � $ � & � ! � # # � � % # � + $ � ) ! � * ! # � �

772AE0457 772AE0457450 457.2 20.7 339.58 6.4 541.3 638.0 77.7

3– 30.8� & � & � � � � $ � � � " $ % � � � # ! # � � $ � # ! � � # $ � � � � ) ! � * � & � �

772AE0508 772AE0508500 508.0 20.7 419.23 6.4 596.9 708.2 77.7

4– 40.4# � # � � � � � $ � � + % " # % & � � # ! # $ � ! � # � & & $ � � � � � ( ) ! ' � & + � �

772AE0610 772AE0610600 609.6 17.2 503.08 6.4 701.8 812.8 81.0

4– 43.5# % # % � � � � # ! � � � $ " � + � � # ! # � � $ $ # � � � $ � � + � � ( ) ! ' � + � � �

= 1 for red paint finish, 2 for hot dipped galvanised finish

* Maximum available gap between pipe ends. Minimum gap = 0.

† Maximum Pressure and End Load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thicknesses. Contact a GRINNELL Sales Representative for details.

‡ Max End Gap is for cut grooved standard weight pipe. Values for roll grooved pipe will be half that of cut grooved.

The Fig. 772 Heavy Duty Rigid Coupling does not provide compensation for pipe system expansion and/or contraction associated with pipe system temperature changes.

For information on alternative sizes, contact a GRINNELL Sales Representative.

See page 19 for coupling specifications and pages 234 - 245 for gasket information.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings


Figure 740 Rapid Installation Pivot-Bolt (GRIP) Rigid CouplingsTech Data Sheet: G144

The Figure 740 GRINNELL Rapid Installation Pivot-Bolt (GRIP) Rigid Coupling, provides a rigid joint in one tenth the time of traditional joining methods and in half the time of standard grooved Couplings.

Figure 740 GRIP Couplings are a proven, dependable, and more efficient method of joining pipe. Simply push the EHT gasket onto the pipe, swing the coupling body over the gasket, and tighten only one bolt. In comparison with other installation-ready couplings, the Figure 740 GRIP Coupling allows clear visual confirmation that the gasket is properly seated on the gasket sealing surfaces.

Certified toNSF/ANSI 61

For detailed Listing / Approval

information contact

GRINNELL Mechanical Products

B C

A

PIVOT

BOLT

COUPLING

BOLT

Part Number

Pipe Size Max.†Pressures

Barpsi

Max.†End Load

kNLbs.

Max. End Gap mmInches

Dimensions Pivot Bolts SizeInches

Dia x Lg.

Coupling Bolts SizeInches

Dia x Lg.

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

AmmInches

BmmInches

CmmInches

740AE0060*50 60.3 51.7 14.78 8.3 84.5 147.8 53.8

1 ⁄ 2 x 3- 3 ⁄4 1 ⁄ 2 x 3- 5 ⁄ 81.5# # � $ ! ! � $ " $ # $ � � $ $ $ � $ $ ! � & # # � � # $ � $

740AE0073*65 73.0 51.7 21.66 8.3 97.3 160.3 53.8

1 ⁄ 2 x 3- 3 ⁄4 1 ⁄ 2 x 3- 5 ⁄ 81.6# � * # � & ! ! � % " & � + � � $ $ $ � & $ � � $ � # � � # $ � !

740ME0076*65 76.1 8.3 100.5 163.5 54.1

1 ⁄ 2 x 3- 3 ⁄4 1 ⁄ 2 x 3- 5 ⁄ 81.6 � � � , , $ � � � � � � $ $ $ � + � � � % % # � � $ $ � �

740AE0089*80 88.9 51.7 32.10 8.3 112.8 175.8 54.4

1 ⁄ 2 x 3- 3 ⁄4 1 ⁄ 2 x 3- 5 ⁄ 81.7$ $ � ! � � ! � " # � � � � $ $ % � % % � � + # # � � % $ �

740AE0114*100 114.3 51.7 53.06 9.8 145.6 205.7 56.4

1 ⁄ 2 x 3- 3 ⁄4 1 ⁄ 2 x 3- 5 ⁄ 82.3% % � ! � � ! � � � " + # & � � $ + ! � $ & � � � # � # # ! � �

740ME0139*125 139.7 9.8 169.7 244.9 58.7

5 ⁄ 8 x 4- 1 ⁄ 2 5 ⁄ 8 x 4- 1 ⁄ 23.5� $ + � , , ! � ! � � � � $ + � � � & + � � % # � $ � �

740AE0141*125 141.3 51.7 81.09 9.8 172.4 246.6 58.7

5 ⁄ 8 x 4- 1 ⁄ 2 5 ⁄ 8 x 4- 1 ⁄ 23.5! ! � ! � $ ! � � & " # # + � � $ + � � + + � � # � $ � �

740ME0165*150 165.1 9.8 198.4 270.8 58.9

5 ⁄ 8 x 4- 1 ⁄ 2 5 ⁄ 8 x 4- 1 ⁄ 23.9� � ! � � , , � � ! � � � � $ + � & � � � � � � # � $ # & � �

740AE0168*150 168.3 48.2 107.34 9.8 201.7 274.1 58.9

5 ⁄ 8 x 4- 1 ⁄ 2 5 ⁄ 8 x 4- 1 ⁄ 23.9� � � � # ! � � # % " � $ � � � $ + � + % � � � + # � $ # & � �

740AE0219*200 219.1 41.4 155.94 11.3 256.3 326.1 71.9

5 ⁄ 8 x 4- 1 ⁄ 2 5 ⁄ 8 x 4- 1 ⁄ 25.8& & � � # ! � � � $ ! " � ! � � � % ! � � � � + � # � & % # � & $ � # � &

= 1 for red paint finish,or 2 for hot dipped galvanised finish

† Maximum Pressure and End Load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thickness. Contact a GRINNELL Sales Representative for details.

Contact a GRINNELL Sales Representative for more information.





GROOVED COUPLINGS

Grooved

Couplings

23

Figure 774 Rigid CouplingsTech Data Sheet: G135


PressuresBar� � � Max.†

End LoadkNF G � � Max.*‡

End Gap mmH I J K L � Dimensions Coupling

Bolts Size **(Qty 2) mmH I J K L � Approx.

WeightkgF G � �Grade “E”

Gasket


Nominal mmH I J K L � O.D.

mmH I J K L � AmmInches

BmmInches

CmmInches

774ME0034 774MT003425 33.7 34.5 2.11 1.5 41 100 42 M10 x 57 0.55� � � $ � ! ! � � % ! � � � � � � � $ $ � + # � � � ! ' ( ) # � � � � #

774ME0042 774MT004232 42.4 34.5 3.37 1.5 68 112 42 M10 x 57 0.59� � � � � � � � ! � � ! � � � � # � � � % � % � � � � % ' ( ) # � � � � $

774ME0048 774MT004840 48.3 34.5 4.41 1.5 74 118 42 M10 x 57 0.68� � * � � + � � ! � � + + # � � � � # � + � % � � � � � � � ' ( ) # � � � � !

774ME0060 774MT006050 60.3 34.5 6.90 1.5 86 132 43 M10 x 57 0.82# # � $ ! ! � � � " ! ! � � � � � $ � $ & ! � # � � � � ' ( ) # � � � � &

774ME0073 774MT007365 73.0 34.5 10.11 1.5 99 143 44 M10 x 57 0.91# � * # � & ! ! � � # " # # � � � � $ � & & ! � � % � � ! ' ( ) # � � # � �

774ME0076 774MT007665 76.1 34.5 11.01 1.5 102 147 44 M10 x 57 0.91 � � � , , $ � � � � ! � � # " % % � � � � % � � � ! � & � � ! - # � �

774ME0089 774MT008980 88.9 34.5 14.98 1.5 114 161 44 M10 x 57 1.50$ $ � ! � � ! � � $ " $ � � � � � % � ! � � � $ $ � � ! ' ( ) # � � $ � $

774ME0114 774MT0114100 114.3 34.5 21.22 1.5 145 191 46 M10 x 57 1.50% % � ! � � ! � � % " � � � � � ! � � � ! � � � & $ ' ( ) # � � $ � $

774ME0139 774MT0139125 139.7 34.5 31.71 3.2 173 222 49 M12 x 76 2.41� $ + � , , ! � ! � � ! � � " � # � � � # ! � � & � & � ! � � + � - ! � $

774ME0141 774MT0141125 141.3 34.5 32.43 3.2 174 224 49 M12 x 76 2.41! ! � ! � $ ! � � " # + � � � � # ! � � & � & � & # � � + � � * ) $ ! � $

774ME0165 774MT0165150 165.1 34.5 44.28 3.2 198 248 49 M12 x 76 2.59� � ! � � , , � � ! � � ! � � + " + ! ! � � � # ! � & � + � ! � � + � - ! �

774ME0168 774MT0168150 168.3 34.5 46.00 3.2 215 251 49 M12 x 76 2.69� � � � # ! ! � � � � " $ % � � � � # ! & � % + � & & � � + � � * ) $ ! � +

774ME0219 774MT0219200 219.1 27.5 77.97 3.2 260 325 61 M16 x 83 5.32& & � � # ! % � � � " ! # & � � � # ! � � � # ! � # � & # � % � . ( ) $ � � � � �

774ME0273 774MT0273250 273.0 16.0 70.7 6.4 318 419 65 M20 x 121 8.86� � � � � ! � # $ $ � ! " & & $ � � # ! � # � ! � � � � ! � # � ! � ' � ) % ' � � + � !

774ME0324 774MT0324300 323.9 12.0 99.4 6.4 368 470 65 M20 x 121 10.00� # � # � ! � � ! # # " $ % $ � � # ! � % � ! � � & � ! � # � ! � ' � ) % ' � # # � �

The 774 Coupling will be available from Sept. 2013 – For information on alternative product, contact a GRINNELL Sales Representative

= 1 for red paint finish, 2 for hot dipped galvanised finish, or 5 for painted white RAL 9010 coating


† Maximum Pressure and End Load are total from all loads based on on standard weight steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thicknesses. Contact a GRINNELL Sales Representative for details.

‡ Max End Gap is for cut grooved standard weight pipe. Values for roll grooved pipe will be half that of cut grooved.

** Gold colour coded metric bolt sizes for 25mm - 300mm couplings are available upon request.

The Fig. 774 Standard Weight Rigid Coupling does not provide compensation for pipe system expansion and/or contraction associated with pipe system temperature changes.




The GRINNELL Figure 774 Grooved Rigid Coupling provides a rigid joint by firmly gripping along the full circumference of the pipe grooves. Figure 774 Grooved Rigid Couplings are a proven dependable method of joining pipe and are an economical alternative to welding, threading, or using flanges. It is capable of pressures up to 34.5 Bar (500 psi) depending on pipe size and wall thickness when used in fire protection services.MN O



Issue 03, 04, 07

Cert No. 570, 669, 673

www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings


P QRFigure 705 Flexible CouplingsTech Data Sheet: G110 The GRINNELL Figure 705 Flexible Coupling allows for angular and linear

deflection, thermal expansion and contraction, and misalignments of pipe. It is capable of pressures up to 34.5 Bar (500 psi), depending on pipe size and wall thickness. Suitable for use in a variety of applications, the GRINNELL Figure 705 Coupling provides a dependable method of joining pipe.

Part Number Pipe Size

Max.†Pressure

Bar� � � Max.†End LoadkNF G � � Max.*‡

End Gap mmH I � Deflection ‡ Dimensions - mm

H I �Coupling Bolts Size(Qty 2) mmH I � Approx.

WeightkgF G � �Grade “E”

Gasket


Nominal DNH I � O.D.

mmH I � Deg.Per

Coupling

mm/mH I � S T U A B C

705ME0034 705MT003425 33.7 34.5 1.86 3.3

5° 30'96.7 56.9 100.1 46.0 M10 x 57 0.6� � � $ � !

500% � � � � � $ � � � � # � # % $ � + % � � & � ' ( ) # � � � � $

705ME0042 705MT004232 42.4 34.5 4.81 3.3

4° 19'75.0 65.0 106.4 46.0 M10 x 57 0.7� � � � � � � �

500� " � & # � � � $ � � + � # � ! � % � � + � � & � ' ( ) # � � � � !

705ME0048 705MT004840 48.3 34.5 6.30 3.3

3° 46'65.8 69.9 112.8 46.0 M10 x 57 0.7� � * � � + � �

500� " % � & � � � $ � � + # � ! % � % % � � & � ' ( ) # � � � � �

705ME0060 705MT006050 60.3 34.5 9.85 3.3

3° 1'52.5 82.6 124.0 47.8 M10 x 57 0.8# # � $ !

500# " # � ! � � � $ � � � $ $ � # ! % � & & � � & & ' ( ) # � � � �

705ME0073 705MT007365 73.0 34.5 14.43 3.3

2° 29'43.3 93.7 139.7 47.8 M10 x 57 0.9# � * # � & !

500$ " # % � � � � $ � � ! # $ � � + ! � ! � � � & & ' ( ) # � � # � �

705ME0076 705MT007665 76.1 34.5 15.72 3.3

2° 23'41.7 101.6 146.10 47.8

M12 x 761.4 � � � , , $ � � � �

500$ " ! $ % � � � $ � � ! � % � � � ! � ! � � & & $ � �

705ME0089 705MT008980 88.9 34.5 21.39 3.3

2° 3'35.8 111.3 165.1 47.8 M12 x 89 1.4$ $ � ! � �

500% " & � � � � � $ � � % $ % � $ & � � ! � � � & & � * ) $ $ � �

705ME0108 705MT0108100 108.0 34.5 31.55 6.4

3° 22'58.3 140.0 191.0 52.0 M12 x 76 1.9� � & � � , , % � # ! #

500 " � + $ � � # ! � � � ! � ! � � ! # # � � ! % � #

705ME0114 705MT0114100 114.3 34.5 35.35 6.4

3° 11'55.8 144.5 196.9 52.3 M12 x 89 1.8% % � ! � �

500 " + ! # � � # ! � � � ! � � + � ! # � � � � * ) $ % � �

705ME0133 705MT0133125 133.0 31.0 43.33 6.4

2° 44'46.7 167.0 241.0 52 M16 x 83 3.3� $ $ � � , , ! � # $ �

450+ " % � � � # ! � � ! � � � ! + � % + # � � ! - � #

705ME0139 705MT0139125 139.7 31.0 47.56 6.4

2° 36'45.5 173.0 247.7 52.3 M16 x 83 3.3� $ + � , , ! � ! � �

450� � " � + � � � # ! � � ! ! � � & � + � ! # � � � - � #

705ME0141 705MT0141125 141.3 31.0 48.63 6.4

2° 35'45.0 174.8 247.7 52.3 M16 x 83 3.2! ! � ! � $

450� � " + $ & � � # ! � � ! % � � & & + � ! # � � � . ( ) $ � � � �

705ME0159 705MT0159150 159.0 31.0 61.41 6.4

2° 35'40.0 192.0 261.9 52.3 M16 x 83 3.4� ! + � � , , � � # � �

450� $ " & � � � � # ! � � % & � ! � � � � $ � # � � � - � %

705ME0165 705MT0165150 165.1 31.0 66.36 6.4

2° 12'38.3 196.9 271.5 52.3 M16 x 83 3.2� � ! � � , , � � ! � �

450� % " + $ # � � # ! � � % � � ! � � � � + # � � � - � �

705ME0168 705MT0168150 168.3 31.0 68.97 6.4

2° 10'37.5 201.7 271.5 52.3 M16 x 83 3.2� � � � # !

450� ! " ! � # � � # ! � � % ! � + % � � � � + # � � � . ( ) $ � � � �

705ME0219 705MT0219200 219.1 31.0 116.89 6.4

1° 40'29.2 258.8 344.4 63.5 M20 x 121 6.6& & � � # !

450# � " # + # � � # ! � � $ ! � � � � + � $ � ! � # � ! � ' � ) % ' � � % � !

705ME0273 705MT0273250 273.0 24.1 141.31 6.4

1° 20'23.3 322.3 416.1 66.8 – 12.7� � � � � ! � $ ! � $ � " � � � # ! � � # & � # � � + � � � $ & # � � $ � ) � � * # & � �

705ME0324 705MT0324300 323.9 24.1 198.78 6.4

1° 7'19.2 379.5 479.6 66.8 – 16.6� # � # � ! � $ ! � % % " � & � � # ! � � # $ � % � + % � & � & & # � � $ � ) � � * $ � � !

= 1 for red paint finish, 2 for hot dipped galvanised finish, or 5 for painted white RAL9010 coating


† Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thickness. Contact GRINNELL Products for details.

‡ Max end gap and deflection is for cut grooved standard weight pipe. Values for roll grooved pipe will be half that of cut grooved.






Issue 03, 04, 07

Cert No. 570, 669, 673


GROOVED COUPLINGS

Grooved

Couplings

25

Figure 770 High Pressure Rigid CouplingsTech Data Sheet: G138

The Figure 770 Rigid Coupling provides a rigid joint by firmly gripping along the circumference of the pipe grooves. This coupling offers a dependable method for joining pipe and is an economical alternative to welding, threading, or using flanges. It is capable of pressures up to 68.9 Bar (1000 psi) depending on pipe size and wall thickness.

0/1Additional Features:

provides a strong rigid connection.

Warranty.

Part Number


Barpsi

Max.†End Load

kNLbs.


Dimensions - mm Inches Coupling Bolts Approx.WeightKg.Lbs.

Nominal mmInches

O.D.mmInches

A B C Qty.SizemmInches

770AE006050 60.3 68.9 19.71 3.6 89.7 145.3 47.8

2M16 x 70 2.0# # � $ ! � � � � % " % $ � � � � % $ � ! $ ! � # � � & & . ( ) # ' � % � $

770AE007365 73.0 68.9 28.88 3.6 103.1 152.4 47.8

2M16 x 89 2.3# � * # � & ! � � � � � " % + # � � � % % � � � � � � � � � & & . ( ) $ � * ! � �

770AE008980 88.9 68.9 42.79 3.6 121.4 171.7 47.8

2M16 x 89 2.4$ $ � ! � � � � � � + " � # � � � � % % � & � � � � � & & . ( ) $ � * ! � $

770AE0114100 114.3 68.9 70.74 6.4 152.7 215.9 53.3

2M20 x 108 3.5% % � ! � � � � � � � ! " + � % � � # ! � � � � & � ! � # � � � ' � ) % � � �

770AE0168150 168.3 68.9 153.33 6.4 216.2 285.8 53.3

2M22 x 140 7.3� � � � # ! � � � � $ % " % # � � # ! & � ! � � � � # ! # � � � V ( ) ! � * � � � #

770AE0219200 219.1 55.2 207.90 6.4 277.6 349.3 66.0

2– 10.9& & � � # ! & � � % � " % � � � # ! � � � + $ � $ � ! # � � � � ) ! � * # % � �

770AE0273250 273.0 55.2 322.97 6.4 341.9 406.4 66.0

2– 14.5� � � � � ! � & � � # " � � � � � # ! � $ � % � � � � � � # � � � � ) � � * $ # � �

770AE0324300 323.9 55.2 454.32 6.4 394.2 457.2 66.0

2– 18.1� # � # � ! � & � � � � # " � % � � � # ! � ! � ! # � & � � � # � � � � ) � � * % � � �



† Maximum Pressure and End Load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thickness. Contact a GRINNELL Sales Representative for details.

‡ Max End Gap and Deflection is for cut grooved standard weight pipe. Values for roll grooved pipe will be half that of cut grooved.




www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings


Figure 707 Heavy Duty Flexible Couplings(Page 1 of 2)


0/ 101/01 /3 6 4 4 5 2 6 7 4 4 8 9 < = 9 > < ? @ 7 7 4 4 5 @ 6 7 4 4 8 9 A < = 9 B < ? 6 7 7 4 4 5 C 7 7 4 4 8 D E < = D > < ?Part

Number

Pipe SizeMax.†


End LoadkNLbs.


Deflection ‡ Dimensions - mm In. Coupling BoltsApprox.WeightKg.Lbs.

Nominal mmInches

O.D.mmInches

DegreesPer

Coupling

mm/mInches/Ft


707AE003425 33.7 68.9 6.10 3.3

5° 26'98.4 60.5 101.6 46.0

2M12 x 89 0.9� � � $ � ! � � � � � " $ � � � � � $ � � � % # � $ & % � � � � � & � � * ) $ # � �

707ME004232 42.4 68.9 9.63 3.3

4° 19'75.0 70.0 111.0 46.0

2M12 x 89 1.0� � � � � � � � � � � � # " � � ! � � � $ � � + � # � � % � $ � � & � � * ) $ # � #

707AE004840 48.3 68.9 12.61 3.3

3° 46'65.8 75.4 117.6 46.0

2M12 x 89 1.1� � * � � + � � � � � � # " & $ ! � � � $ � � + # � + % � � $ � � & � � * ) $ # � !

707AE006050 60.3 68.9 19.71 3.3

3° 1'52.5 89.9 133.4 47.8

2M12 x 89 1.4# # � $ ! � � � � % " % $ � � � � $ � � � $ $ � ! % ! � # ! � � & & � * ) $ $ � �

707AE007365 73.0 68.9 28.88 3.3

2° 29'43.3 103.1 146.1 47.8

2M12 x 89 1.6# � * # � & ! � � � � � " % + # � � � $ � � ! # % � � � ! � ! � � & & � * ) $ $ � !

707AE007665 76.1 68.9 31.44 3.3

2° 23'41.7 106.4 146.1 47.8

2M12 x 89 1.8 � " � , , $ � � � � � � � � " � � + � � � $ � � ! � % � � + ! � ! � � & & - % � �

707AE008980 88.9 68.9 42.80 3.3

2° 3'35.8 119.1 162.1 47.8

2M12 x 89 1.8$ $ � ! � � � � � � + " � # � � � � $ � � % $ % � � + � � $ & � � & & � * ) $ % � �

707AE0114100 114.3 68.9 70.75 6.4

3° 11'55.8 151.1 209.6 52.3

2M16 x 83 3.2% % � ! � � � � � � � ! " + � % � � # ! � � � ! � + ! & � # ! # � � � . ( ) $ � � � �

707AE0139125 139.7 68.9 105.6 6.4

2° 30'43.3 178.3 254.0 51.8

2M20 x 121 3.8� $ + " , , ! � ! � � � � � � # $ " ! & � � # ! � � ! # � � # � � � � � # � � % ' � ) % ' � & � $

707AE0141125 141.3 68.9 108.12 6.4

2° 35'45.1 179.8 254.0 52.3

2M20 x 121 4.5! ! � ! � $ � � � � # % " $ � � � � # ! � � ! % � � & � � � � � # � � � ' � ) % ' � � � � �

707AE0165150 165.1 68.9 147.61 6.4

2° 12'38.4 208.0 285.8 52.3

2M20 x 121 5.4� � ! " � , , � � ! � � � � � � $ $ " � & $ � � # ! � � % � & � � + � � � # ! # � � � - � # � �

707AE0168150 168.3 68.9 153.34 6.4

2° 10'37.8 210.8 285.8 52.3

2M20 x 121 5.0� � � � # ! � � � � $ % " % # � � # ! � � % ! & � $ � � � � # ! # � � � ' � ) % ' � � � � �

The GRINNELL Figure 707 Heavy Duty Flexible Coupling allows for angular and linear deflection, thermal expansion and contraction, and misalignments of the pipe. Flexible couplings can act as an “expansion joint”, allowing linear and angular movement of the pipes when properly installed. This coupling is capable of pressures up to 68.9 Bar (1,000 psi), depending on pipe size and wall thickness. Suitable for use in a variety of applications, the Figure 707 Coupling provides a dependable method of joining pipe.



Issue 03, 04, 07

Cert No. 570, 669, 673


GROOVED COUPLINGS

Grooved

Couplings

27

0/ 101/01 /3 6 4 4 5 2 6 7 4 4 8 9 < = 9 > < ? @ 7 7 4 4 5 @ 6 7 4 4 8 9 A < = 9 B < ? 6 7 7 4 4 5 C 7 7 4 4 8 D E < = D > < ?

Figure 707 Heavy Duty Flexible Couplings(Page 2 of 2)


Part Number

Pipe SizeMax.†


End LoadkNLbs.


Deflection ‡ Dimensions - mm In. Coupling BoltsApprox.WeightKg.Lbs.

Nominal mmInches

O.D.mmInches

DegreesPer

Coupling

mm/mInches/Ft


707AE0219200 219.1 55.2 207.91 6.4

1° 40'29.2 271.3 355.6 62.7

2M22 x 165 9.7& & � � # ! & � � % � " % � � � # ! � � $ ! � � � � & � % � � � # � % V ( ) � � * # � � %

707AE0273250 273.0 55.2 322.99 6.4

1° 20'23.3 331.7 417.6 66.8

2– 13.2� � � � � ! � & � � # " � � � � � # ! � � # & � $ � � � � � � % % # � � $ � ) � � * # + � �

707AE0324300 323.9 55.2 454.35 6.4

1° 7'19.2 390.9 478.5 66.8

2– 16.8� # � # � ! � & � � � � # " � % � � � # ! � � # $ � ! � $ + � & � & % # � � $ � ) � � * $ � �

707AE0355350 355.6 20.7 205.43 6.4

1° 2'18.3 423.4 517.7 74.7

2– 20.9� % � % � � � � $ � � % � " � & � � � # ! � � # # � � � � # � � $ & # � + % � ) ! � * % � � �

707AE0406400 406.4 20.7 268.31 6.4

0° 54'15.8 478.3 575.1 74.7

3– 26.8� � � � � � � � $ � � � � " $ � & + � � # ! � � � + � & � & $ # # � � % # � + % � ) ! � * ! + � �

707AE0457450 457.2 20.7 339.58 6.4

0° 48'14.2 541.3 638.0 77.7

3– 35.4� & � & � � � � $ � � � " $ % � � � # ! � � � # � � $ � # ! � � # $ � � � � ) ! � * & � �

707AE0508500 508.0 20.7 419.23 6.4

0° 43'12.5 596.1 708.2 77.7

4– 40.4# � # � � � � � $ � � + % " # % & � � # ! � � � ! # $ � % # � & & $ � � � � � ( ) ! ' � & + � �

707AE0610600 609.6 20.7 603.7 6.4

0° 36'10.8 700.5 812.8 81.0

4– 50.8# % # % � � � � $ � � � $ ! " � � � # ! � � � $ # � ! & $ # � � � $ � � + � � ( ) ! ' � � � # � �



† Maximum Pressure and End Load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thicknesses. Contact a GRINNELL Sales Representative for details.

‡ Max End Gap and Deflection is for cut grooved standard weight pipe. Values for roll grooved pipe will be half that of cut grooved.


For coupling sizes above 300mm (12" ) bolt sizes only available in ANSI.



www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings


Figure 707L Large Diameter CouplingsTech Data Sheet: G133

GRINNELL Figure 707L Large Diameter Coupling is designed for joining large diameter IPS roll grooved pipes. The coupling castings are a two to eight segment design and utilize two bolts at each segment joint to ensure proper connection and seal.

Suitable for use in a variety of applications where there is a need to move large volumes of fluids, the Figure 707L Large Diameter Coupling provides a dependable method of joining pipe.

Pipe Size Max. † Working Pressure

Barpsi

Max. † End Load

kNLbs

Max.* ‡ End Gap mminches

Dimensions BoltsApprox.WeightKg.Lbs.

Nominal mmInches

O.D.mmInches

AmmInches

BmmInches

CmmInches

No Sizein

650 660.4 20.7 708 8.6 754.0 842.0 125.64

V ( ) + W . ( 67.0# � # � � � $ � � � ! + " # + � � $ % # + � � & $ $ � � ! % � + % � % � �700 711.2 12.1 479 8.6 813 920 127

12V ( ) % 82.0# & # & � � � ! � � " ! � � $ % $ # � � $ � � $ ! � � � & � � �

750 762.0 12.1 550 8.6 864 972 12712

V ( ) % 95.0$ � $ � � � � ! � # $ " � � � � $ % $ % � � $ & � $ ! � � # � + � �800 812.8 12.1 626 8.6 914 1022 127

12V ( ) % 94.0$ # $ # � � � ! � % � " % $ � � $ % $ � � � % � � $ ! � � # � � �

900 914.4 12.1 792 8.6 1016 1124 12712

V ( ) % 96.0$ � $ � � � � ! � & " � # & � � $ % % � � � % % � $ ! � � # � # � �1000 1016.0 12.1 978 8.6 1105 1245 140

16� ) $ � * 123.0% � % � � � � ! # � + " + � � � � $ % % $ � ! % + � � ! � ! # � � �

1050 1066.8 12.1 1078 8.6 1156 1295 14016

� ) $ � * 140.0% # % # � � � ! # % # " % ! # � � $ % % ! � ! ! � � ! ! � ! $ � & � �† Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ for

other pipe materials and/or wall thickness. Contact your GRINNELL Representative for details.


‡ Max End Gap is for rolled grooved standard weight pipe.




B

B

B

A

C

C

C

DN700 - DN900 (28" - 36") DN1000 - DN1050 (40" - 42")DN650 (26")

A

A


GROOVED COUPLINGS

Grooved

Couplings

29

Shurjoint Figure 7707N Large Diameter Flexible Couplings

Shurjoint Tech Data Sheet: C-23The Shurjoint Model 7707N is a two-segment, flexible coupling for use with standard pipe, roll or cut grooved to AWWA C606 specifications.

The Model 7707N Heavy Duty Flexible Coupling is designed for use in a variety of general piping applications of moderate or high pressure services. The Model 7707N couplings feature flexibility that can deal with misalignment, distortion, thermal stress, vibration and noise and also resist seismic tremors. With the use of Model 7707N couplings you can even design a curved layout. See Typical application – Flexible Couplings on Shurjoint Data Sheet #B-19.

The Model 7707N couplings sizes 350 – 600mm (14” – 24”) are com-prised of two identical ductile iron housing segments, an EPDM rubber gasket and one at each segment joint to ensure a positive connection and seal.

Pressure-Temperature Rating

Pipe Size Max. Working PressureAxial

DisplacementmmInches

Angular Movement Dimensions BoltsApprox.WeightKg.Lbs.

NominalmmInches

ActualO.D.mmInches

XS (0.500”)*

Barpsi

STD (0.375”)Barpsi

LW (0.312”)Barpsi

Degree Per

Coupling (°)

Per Pipemm / m in / ft

AmmInches

BmmInches

CmmInches

No.Sizein

350 355.6 20 20 17 6.41° – 02’

9.0 412 479 75 # 15.7� % � % � � � � $ � � $ � � # ! � � � # ! � � � � � � � � # $ � & � & ! # � + ! V ( ) � � * $ % � !400 406.4 20 20 17 6.4

0° – 54’8.0 463 547 75 # 18.4� � � � � � � � $ � � $ � � # ! � � � # ! � � � � � � & � # $ # � � ! $ # � + ! � ) � � * % � � !

450 457.2 20 20 17 6.40° – 48’

7.0 520 605 79 # 22.3� & � & � � � � $ � � $ � � # ! � � � # ! � � � � & # � � % ! # $ � & � $ � � � � ) � � * % � �500 508.0 20 20 17 6.4

0° – 44’6.0 571 656 79 # 24.5# � # � � � � � $ � � $ � � # ! � � � # ! � � � � & # # � % & # ! � & # $ � � � � ) � � * ! % � �

550 558.8 20 20 17 6.40° – 39’

6.0 621.4 724.6 79 # 28.6# # # # � � � � $ � � $ � � # ! � � � # ! � � � � # % � % � # & � ! # $ � � � � ( ) � � * � $ � �600 609.6 20 20 17 6.4

0° – 36’5.0 674 780 79 # 29.5# % # % � � � � $ � � $ � � # ! � � � # ! � � � � � # � � ! ! $ � � � $ � � � � ( ) � � * � ! � �

Deflection or angular movement is the maximum value that a coupling allows under no internal pressure.

* Pressure ratings are based on cut-grooved XS carbon steel pipe.

Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.




Nom. Rating

Working Pressure(S40S, Roll-grooved)

Max. ServiceTemperature

Class 150

20.7 Bar @38°C$ � � � � � X � � � Y T EPDM: 110°CZ [ \ ] ^ # $ � Y TNitrile: 82°C_ � U ` � a L ^ � & � Y T

*Working pressure is based on roll- or cut-grooved standard wall carbon steel pipe.

*Proof test pressure: 1.5 times the working pressure, non-shock cold water.

*Burst pressure is engineered minimum 2 times the working pressure.

1 0/

Surface Finish:

for waste water, hydrocarbons, harsh chemicals and sea water services, Drynamels #4900 for exterior (outdoor) architectural applications and others (Option).

For additional details contact Shurjoint.

www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings


The GRINNELL Figure 909 Plain End Coupling utilizes hardened gripping teeth to securely grip onto plain and beveled end pipe surfaces. It is capable of pressures up to 51.7 Bar (750 psi) depending on pipe size and wall thickness.

The GRINNELL Figure 909 Plain End Coupling is designed for Schedule 40 steel pipe and is not for use with steel pipe with a Brinnell hardness greater than 150 HB, plastic, cast, or ductile iron pipes. Contact a GRINNELL Sales Representative for recommendations on other materials and pipe schedules.

6 7 4 4 5 b 6 7 4 4 8 D < = A < ? c 3 1 d e f g h 3 7 7 4 4 5 @ 7 7 4 4 8 B < = 9 A < ? c @ 1 d e f g h10 01/ /

Figure 909 Plain End CouplingsTech Data Sheet: G190

Part Number


Barpsi

Max.†End Load

kNLbs.

Dimensions Coupling Bolts Approx.WeightKg.Lbs.

Nominal mmInches

O.D.mmInches

AmmInches

BmmInches

CmmInches

Qty.SizemmInches

909AE006050 60.3 51.7 14.78 93.7 146.1 84.1

2M16 x 90 2.4# # � $ ! ! � $ $ # # � � $ � � + ! � ! $ � $ � . ( ) $ � * ! � %

909AE007365 73.0 41.4 17.33 105.9 158.8 84.1

2M16 x 90 2.7# � * # � & ! � � � $ & + ! � � % � � � � # ! $ � $ � . ( ) $ � * ! � +

909AE007665 76.1 41.4 23.00 111.9 181.1 98.6

2M20 x 121 2.1 � � � , , $ � � � � � � � ! " � � � � % � % � � � $ $ � & & ' � ) % ' � % � �

909AE008980 88.9 41.4 25.68 122.2 192.0 84.1

2M20 x 121 4.1$ $ � ! � � � � � ! # � % � & � � ! � $ � $ � ' � ) % ' � + � �

909AE0114100 114.3 31 31.83 150.6 219.2 98.6

2M20 x 121 6.1% % � ! � � % ! � " � ! � � + ! � + $ & � � $ $ � & & ' � ) % ' � � $ � !

909AE0165150 165.1 20.7 44.30 203.7 293.7 293.6

2– 9.8� � ! � � , , � � ! � � $ � � + " + ! + � � & � � # � � � ! � � � � ! � � ) � � * # � � �

909AE0168150 168.3 20.7 46.00 208.0 296.7 108.0

2– 10.7� � � � # ! $ � � � � " $ % � � ! & � � + � � � � & % � # ! � ) � � * # $ � !

909AE0219200 219.1 17.2 64.97 271.5 346.2 124.7

4M22 x 140 15.9& & � � # ! # ! � � % " � � � � � � � � � + � $ � � $ % � + � V ( ) ! � * $ ! � �

909AE0273250 273.0 17.2 100.93 333.5 403.4 124.7

4M22 x 140 22.0� � � � � ! � # ! � # # " � + � � � � $ � � $ � ! � & & % � + � V ( ) ! � * % & � !


† Maximum Pressure and End Load are total from all loads based on standard weight steel pipe.

Pressure ratings and end loads may differ for other pipe materials and/or wall thickness. Contact a GRINNELL Sales Representative for details.


See page 19 for plain end coupling specifications and pages 234 - 245 for gasket information.



GROOVED COUPLINGS

Grooved

Couplings

31

The GRINNELL Figure 780 Grooved Snap Coupling is designed for quickly connecting and disconnecting cut or rolled grooved piping systems. By utilizing a hinged lever mechanism, grooved piping segments are joined quickly and securely without nuts and bolts. Coupling housing segments are locked in place by securing the lever handle with a split pin. Additional Features:

(5" to 8") feature a cross-ribbed housing design for extra strength.

300 psi).

01 /i j e k f l k m

Figure 780 Grooved Snap CouplingsTech Data Sheet: G145

Part Number

Pipe Size Max. † *WorkingPressure

Barpsi

Max. *End Load

kNLbs.

Max. End Gap mmInches

Dimensions DeflectionApprox.WeightKg.Lbs.

Nominal mmInches

O.D.mmInches

AmmInches

BmmInches

CmmInches

DegreesPer

Coupling

mm/mInches/Ft

780AE004840 48.3 20.7 3.8 1.6 75.0 118.0 47.0

3° 48'66.4 1.0� � * � � + � � $ � � & ! � � � � � # � + ! % � � ! � � & ! � � & � # � #

780AE006050 60.3 20.7 5.9 1.6 86.0 121.0 48.0

3° 31'61.5 1.1# # � $ ! $ � � � " $ # + � � � � $ � $ + % � � � � & + � � % # � %

780AE007365 73.0 20.7 8.7 1.6 92.0 150.0 48.0

2° 30'43.7 1.4# � * # � & ! $ � � � " + % � � � � $ � � # ! � + � � � & + � � ! # $ � �

780AE007665 76.1 20.7 9.4 1.6 92.0 150.0 48.0

2° 24'41.9 1.4 � " � , , $ � � � � $ � � # " � # � � � � � $ � � # ! � + � � � & + � � ! � $ � �

780AE008980 88.9 20.7 12.8 1.6 119.0 163.0 48.0

2° 24'41.9 1.8$ $ � ! � � $ � � # " & & � � � � � % � � + � � % # � � & + � � ! � % � �

780AE0114100 114.3 20.7 21.2 3.2 165.0 205.0 52.0

3° 12'55.9 2.7% % � ! � � $ � � % " � � � � $ � � ! � & � � # � � ! � � � ! � +

780AE0139125 139.7 20.7 31.7 3.2 189.0 253.0 52.0

2° 37'45.7 4.9� $ + " , , ! � ! � � $ � � " � # � � � $ � % % + � + � # � � ! � � ! ! � � � &

780AE0141125 141.3 20.7 32.4 3.2 189.0 253.0 52.0

2° 36'45.4 4.9! ! � ! � ! $ � � " # & + � � � $ � % % + � + � # � � ! � � ! % � � � &

780AE0165150 165.1 20.7 44.3 3.2 213.0 278.0 52.0

2° 14'39.0 5.8� � ! " � , , � � ! � � $ � � + " + ! ! � � � $ & � $ + � � � + % # � � ! � � % � # � &

780AE0168150 168.3 20.7 46.0 3.2 216.0 281.0 52.0

2° 10'37.8 5.8� � � � # ! $ � � � � " $ % � � � � $ & � ! � � � � � � # � � ! � � % ! � # � &

780AE0219200 219.1 20.7 78.0 3.2 278.0 356.0 62.0

1° 40'29.1 9.3& & � � # ! $ � � � " ! # & � � � $ � � � + ! � % � � # # � % % � � $ ! # � � !

= 1 for black paint finish, 2 for hot dipped galvanised finish

† Pressure ratings listed are cold water pressure or maximum working pressure within the service temperature range of the gasket used in the coupling.

* Maximum Working Pressures and End Loads listed are total of internal and external pressures and loads based on Schedule 40 steel pipe grooved in accordance with Standard Cut Groove or Roll Groove Specifications.




Coatings

(standard)

(optional)

Toggle Links

to ANSI C1010 or C1020

Hinge Pin

conforming to ANSI C1212

Rivet

ANSI C1010

Split Pin

conforming to ASTM A 421

Gasket Specifications

gaskets have a Green colour stripe code for temperature service from -34°C to 110°C ( -30°F to 230°F).

gaskets have an Orange colour stripe code for temperature service from -29°C to 82°C ( -20°F to 180°F).

Refer to data sheet G610 for more gasket information.

www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings


Shurjoint Figure XH-70EP Extra Heavy Rigid Couplings

With End Protection (EP) GasketShurjoint Tech Data Sheet: C-09

Pipe Size Max. WorkingPressure

Barpsi

Max. EndLoadkNLbs.

Dimensions Bolt / NutBolt

WeightKg.Lbs.

NominalmmInches

O.D.mmInches

AmmInches

BmmInches

CmmInches

No.Sizein

50 60.3 175 50 90 150 492

. ( ) # ' � 1.5# # � $ ! # ! � � � � � � $ � ! % ! � + � � � + # $ � $65 73.0 175 73.2 103 168 49

2. ( ) # ' � 1.8# � * # � & ! # ! � � � � # # � % � � � � � � � � � + # % � �

80 88.9 175 108.6 122 188 512

. ( ) # ' � 2.2$ $ � ! � � # ! � � # % � % � % � & � � % � # � � � % � &100 114.3 175 179.5 157 222 55

2' � ) % ' � 4.0% % � ! � � # ! � � $ + % � � � � & & � % # � � & � &

150 168.3 140 311.3 218 295 572

V ( ) ! � * 8.0� � � � # ! # � � � � & + � � & � ! & � � � � � # � # ! � � �200 219.1 140 527.6 275 364 70

2� ) ! � * 10.9& & � � # ! # � � � � � � + � � � � & $ � % � $ $ # � ! # % � �

250 273.0 88 514.8 334 424 752

� ) ! � * 14.2� � � � � ! � � # ! � � � $ % � � � $ � � ! � � � � # � + ! $ � � #300 323.9 88 724.7 390 480 75

2 � ) ! � * 16.7� # � # � ! � � # ! � � ! + ! � � � ! � $ ! � & � + $ # � + ! $ � �

* Pressures quoted are based on EP cut grooved XS (Sch. 80) pipe.

CAUTION: Always fasten the bolts to the required torque.





EP Gasket

The Shurjoint Model XH-70EP is designed for use with plastic coated or cement lined pipe. The EP (end protection) gasket serves to form a continuous lined surface at the joint and also helps protect the pipe ends from corrosion. This coupling is rated up to 175 Bar (2500 psi) when used in conjunction with machined EP cut grooves and the applicable pipe.

MATERIAL SPECIFICATIONS

Housing:

ASTM A 395 Gr.65-45-15, min. tensile strength 4481 Bar (65,000 psi).

Surface Finish:

Rubber Gasket: “EP” gasket (Colour code: Orange

stripe) Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Also good for water services under 66°C (150°F). Temperature range: -29°C to 82°C (-20°F to 180°F). Do not use for HOT WATER above 66°C (150°F) or HOT DRY AIR above 60°C (140°F)

Bolts & Nuts:

ASTM A 449-83a (or A 183 Gr. 2), minimum tensile strength 7584 Bar (110,000 psi), Zinc electroplated, with heavy-duty hexagonal nuts to ASTM A 563

10 /


GROOVED COUPLINGS

Grooved

Couplings

33

Figure 716 Flexible Reducing CouplingsTech Data Sheet: G120

The GRINNELL Figure 716 Flexible Reducing Coupling allows for a direct transition between two different pipe sizes and replaces two couplings and a reducing fitting. It is capable of pressures up to 34.5 Bar (500 psi) depending on pipe size and wall thickness. A flexible reducing coupling is not recommended for low-temperature applications. 1 /0

Part Number


Bar� � � Max.†End LoadkNF G � � Max.*‡

End GapmmH I � Deflection ‡

Dimensions mm

H I � Coupling Bolts Size(Qty 2) mmH I � Approx.

WeightkgF G � �Nominal

DNH I � O.D.mmH I � Degrees

Per Coupling

mm/mH I � S T U A B C

716AE201550 x 40 60.3 x 48.3 34.5 6.31 3.3

1° 53'32.9 88.9 128.5 47.8 M10 x 57 1.3# ) � W � * # � $ ! ) � � + � � ! � � � % � & � � � $ � � $ + $ � ! � ! � � � � � & & ' ( ) # W � � # � &

716AE252065 x 50 73.0 x 60.3 34.5 9.85 3.3

1° 33'27.1 101.6 139.7 47.8 M120 x 57 1.5# W � * ) # # � & ! ) # � $ ! ! � � # # � ! � � � $ � � $ # % � � � ! � ! � � � & & ' ( ) # W � � $ � $

716ME262065 x 50 76.1 x 60.3 34.5 9.85 3.3

1° 34'27.3 106.4 149.4 47.8 M12 x 89 1.5 � � � , , ) # $ � � � � ) # � $ ! ! � � # # � ! � � � $ � � $ $ % � � + ! � & & � � & & $ � $

716AE302080 x 50 88.9 x 60.3 34.5 9.85 3.3

1° 17'22.4 119.1 165.1 47.8 M12 x 89 2.0$ ) # $ � ! � � ) # � $ ! ! � � # # � ! � � � $ � � # % � � + � � ! � � � & & � * ) $ % � $

716AE302580 x 65 88.9 x 73.0 34.5 14.44 3.3

1° 17'22.4 119.1 165.1 47.8 M12 x 89 1.8$ ) # W � * $ � ! � � ) # � & ! ! � � $ # % � � � � $ � � # % � � + � � ! � � � & & � * ) $ $ � +

716ME302680 x 65 88.9 x 76.1 34.5 15.72 3.3

1° 17'22.4 119.1 165.1 47.8 M12 x 89 1.9$ ) � � � , , $ � ! � � ) $ � � � � ! � � $ ! $ % � � � $ � � # % � � + � � ! � � � & & % � #

716AE4220100 x 60 114.3 x 60.3 34.5 9.85 4.8

2° 38'46.0 152.4 206.5 50.8 M16 x 83 2.4% ) # % � ! � � ) # � $ ! ! � � # # � ! � � � + � � ! ! � � � � & � � $ # � � � . ( ) $ W � � ! � #

716AE4225100 x 65 114.3 x 73.0 34.5 14.44 4.8

2° 38'46.0 152.4 206.5 50.8 M16 x 83 3.0% ) # W � * % � ! � � ) # � & ! ! � � $ # % � � � � + � � ! ! � � � � & � � $ # � � � . ( ) $ W � � � �

716ME4226100 x 65 114.3 x 76.1 34.5 15.72 4.8

2° 38'46.0 152.4 206.5 50.8 M16 x 83 2.8% ) � � � , , % � ! � � ) $ � � � � ! � � $ ! $ % � � � + � � ! ! � � � � & � � $ # � � � � � #

716AE4230100 x 80 114.3 x 88.9 34.5 21.40 4.8

2° 38'46.0 152.4 206.5 50.8 M16 x 83 2.8% ) $ % � ! � � ) $ � ! � � ! � � % & � � � � � + � � ! ! � � � � & � � $ # � � � . ( ) $ W � � � � #

716ME5242125 x 100 139.7 x 114.3 34.5 35.37 6.4

2° 38'46.0 179.3 241.3 52.3 M20 x 121 4.4� $ + � , , ) % ! � ! � � ) % � ! � � ! � � + ! # � � # ! � � ! ! � � � + � ! � # � � � + � �

716AE5342125 x 100 141.3 x 114.3 34.5 35.37 6.4

2° 5'36.4 181.1 242.8 52.3 M20 x 121 4.4! ) % ! � ! � $ ) % � ! � � ! � � + ! # � � # ! � � % % � � $ + � ! � # � � � ' � ) % W ' � + � �

716ME6242150 x 100 165.1 x 114.3 27.6 28.30 6.4

1° 50'32.0 207.8 274.6 52.3 M20 x 121 5.8� � ! � � , , ) % � � ! � � ) % � ! � � % � � � $ � # � � # ! � � $ & & � � & � � � & � # � � � � # � &

716AE6342150 x 100 168.3 x 114.3 27.6 28.30 6.4

1° 44'30.0 212.9 276.4 52.3 M20 x 121 5.8� ) % � � � # ! ) % � ! � � % � � � $ � # � � # ! � � $ � & � $ & � � � & & # � � � ' � ) % W ' � � # � &

716AE6353150 x 125 168.3 x 141.3 27.6 43.25 6.4

1° 44'30.0 212.9 276.4 52.3 M20 x 121 6.3� ) ! � � � # ! ) ! � ! � $ % � � + # # � � # ! � � $ � & � $ & � � � & & # � � � ' � ) % W ' � � $ � &

716AE8063200 x 150 219.1 x 168.3 27.6 61.33 6.4

1° 15'21.0 271.5 349.3 57.2 M22 x 165 9.1& ) � & � � # ! ) � � � # ! % � � � $ & + � � # ! � � # � � � � � + � $ � ! # � # ! V ( ) � W � * # � � �



† Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on other pipe materials and/or wall thickness. Contact GRINNELL Products for details.

‡ Max end gap and deflection is for cut grooved standard weight pipe. Values for roll grooved pipe will be half that of cut grooved.






Issue 03, 04, 07

Cert No. 570, 669, 673

www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings


Figure 702 Mechanical Outlet Couplings(Page 1 of 2)

Tech Data Sheet: G220 The GRINNELL Figure 702 Mechanical Outlet Coupling has the combined features of a coupling and a reducing outlet, eliminating the need for a mechanical tee or other associated couplings. The coupling is available in grooved, male-threaded, or female-threaded outlets. This design makes installation faster, safer, and more cost effective on the job site.

Additional features:(1 1 ⁄ 2" to 6")

(500 psi)

(10" HG)

Figure 702 Outlet Coupling with Female BSP Outlet

Figure 702 Outlet Coupling with Male BSP Outlet

Figure 702 Outlet Coupling with Grooved Outlet

01 // 0101 nRun Pipe Size Branch Size

End GapRange mmH I � Max.

Run End LoadkNF G � � Dimensions

mm H I �

Bolt Size H I � Approx.

Weight kgF G � �Nominal

DNH I � O.D.mmH I � Female n

ThreadmmH I � Male n

ThreadmmH I � Grooved

A B C TNominal mmH I � O.D.

mmH I �40� W � * 48.3� � + � � 21.3 – – – 20-22

6.3� % � & – 114.3 70.0 52.0 ' ( ) # W � ( 1.2� * - - - � � & � W � � & & - % � ! � # � ! # � � � # � �26.9 – – – 20-22 – 114.3 70.0 52.0 1.2' � - - - � � & � W � � & & - % � ! � # � ! # � � � # � �33.7 – – – 20-22 – 114.3 70.0 49.0 1.3� - - - � � & � W � � & & - % � ! � # � ! � � + % # � +

50# 60.3# � $ ! 21.3 – – – 20-22

9.9# # � ! – 127.0 70.0 59.0 ' ( ) # W � ( 1.4� * - - - � � & � W � � & & - ! � � � # � ! # � $ # $ � �26.9 – – – 20-22 – 127.0 70.0 59.0 1.4' � - - - � � & � W � � & & - ! � � � # � ! # � $ # $ � �33.7 33.7 25 33.7 20-22 89.0 127.0 70.0 56.0 1.5� � � � � $ � ! � � & � W � � & & $ � ! � ! � � � # � ! # � # � $ � $

65# W � * 73.0# � & ! 21.3 – – – 32-38

14.4$ # % � – 161.0 83.0 56.0 � * ) # W ' ( 2.2� * - - - � � # ! W � � ! � - � � $ $ $ � # ! # � # � % � &26.9 – – – 32-38 – 161.0 83.0 65.0 2.1' � - - - � � # ! W � � ! � - � � $ $ $ � # ! # � ! � % � �33.7 – – – 32-38 – 161.0 83.0 62.0 4.4� - - - � � # ! W � � ! � - � � $ $ $ � # ! # � % % # � #42.4 42.4 32 42.4 32-38 94.0 161.0 83.0 – 2.3� W � � � W � � � W � � � � � � � � � # ! W � � ! � $ � � � � $ $ $ � # ! - ! � �48.3 48.3 40 48.3 32-38 94.0 161.0 83.0 – 5.9� W � * � W � * � W � * � � + � � � � # ! W � � ! � $ � � � � $ $ $ � # ! - # � %


GROOVED COUPLINGS

Grooved

Couplings

35

Figure 702 Outlet Coupling with Female BSP Outlet

Figure 702 Outlet Coupling with Male BSP Outlet

Figure 702 Outlet Coupling with Grooved Outlet

01 // 0101 n

Figure 702 Mechanical Outlet Couplings(Page 2 of 2)


Run Pipe Size Branch SizeEnd GapRange mmH I � Max.

Run End LoadkNF G � � Dimensions

mm H I �

Bolt Size H I � Approx.

Weight kgF G � �Nominal

DNH I � O.D.mmH I � Female n

ThreadmmH I � Male n

ThreadmmH I � Grooved

A B C TNominal mmH I � O.D.

mmH I �80$ 88.9$ � ! � � 26.9 – – – 32-38

21.4% & � � – 175.0 83.0 72.0 � * ) $ 2.7' � - - - � � # ! W � � ! � - � � & $ � # ! # � & $ ! � +33.7 33.7 25 33.7 32-38 102.0 175.0 83.0 70.0 2.8� � � � � $ � ! � � # ! W � � ! � % � � � � � & $ � # ! # � ! � � #42.4 – – – ♦ ♦ ♦ ♦ ♦ ♦� W � � - - -

♦ ♦ ♦ ♦ ♦ ♦

48.3 48.3 40 48.3 32-38 102.0 175.0 83.0 – 2.9� W � * � W � * � W � * � � + � � � � # ! W � � ! � % � � � � � & $ � # ! - � � %100% 114.3% � ! � � 26.9 – ♦ ♦ 41-46

35.4 + ! # ♦ 211.0 93.0 94.0 . ( ) $ W � * 4.2' � -♦ ♦

� � � $ W � � & �♦

& � $ � $ � � � $ � � + � #33.7 – ♦ ♦ 41-46 ♦ 211.0 93.0 91.0 4.3� -

♦ ♦

� � � $ W � � & �♦

& � $ � $ � � � $ � ! & + � !48.3 48.3 40 48.3 41-46 124.0 211.0 93.0 84.0 4.3� W � * � W � * � W � * � � + � � � � � $ W � � & � % � & & & � $ � $ � � � $ � $ � + � !60.3 60.3 50 60.3 41-46 124.0 211.0 93.0 – 4.5# # # # � $ ! � � � $ W � � & � % � & & & � $ � $ � � � - + � +

150� 168.36.625

33.7 – 25 33.7 41-46

76.7� " # $ ! – 276.0 94.0 121.0 . ( ) $ W � * 6.0� - � � � $ � ! � � � $ W � � & � - � � � & � $ � � % � � � $ � #– – 32 42.4 ♦ ♦ ♦ ♦ ♦ ♦- - � W � � � � � � �

♦ ♦ ♦ ♦ ♦ ♦

48.3 48.3 40 48.3 41-46 154.0 276.0 94.0 121.0 6.2� W � * � W � * � W � * � � + � � � � � $ W � � & � � � � � � � � & � $ � � % � � � $ � �60.3 60.3 50 60.3 41-46 154.0 276.0 94.0 – 6.5# # # # � $ ! � � � $ W � � & � � � � � � � � & � $ � � - � % � $

n Threads are BSP. Some size outlets are available with NPT threads. Contact GRINNELL Products for details.

♦ Contact GRINNELL Sales Representative for dimension details.




www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings


Shurjoint Figure 7706-T Transition Couplings Shurjoint Tech Data Sheet: C-07

Model 7706-T Transition Couplings allows for a direct transition from IPS pipe sizes to ISO pipe sizes.

Pipe Size Max. EndLoadkNLbs.

Axial Displacement

mmInches

Angular Movement Dimensions - mm InchesBolt / Nut Sizein

Approx.WeightKg.Lbs.

NominalmmInches

O.D.mmInches

Per CouplingDegree

Per Pipemm/min/ft.

A B C

65 x 65 73.0 x 76.1 5.90 0 ~ 3.2 # Y W # % o 21.0 102 138 48 M10 x 55 1.2# � * ) � � � , , # � & ! ) $ � � � � � $ $ � W p � � � $ � � # ! % � � # ! � % $ � � & + ' ( ) # � ( # � �150 x 150 168.3 x 165.1 44.29 0 ~ 6.4 � Y W � � o 19.0 200 270 53 M16 x 90 3.5� ) � � ! � � , , � � � # ! ) � � ! � � + + � � � p � � # ! � � # $ � & � � � � $ # � � + . ( ) $ � * �

*Deflection or angular movement is the maximum value that a coupling allows with no internal pressure.





Pressure-Temperature Rating

Nom. Rating

Working Pressure(S40S, Roll-grooved)

Max. ServiceTemperature

Class 15020.7 Bar @ 38°C$ � � � � � X � � � Y T EPDM: 110°CZ [ \ ] ^ # $ � Y T

Nitrile: 82°C_ � U ` � a L ^ � & � Y T*Working pressure is based on roll- or cut-grooved standard wall

carbon steel pipe.

*Proof test pressure: 1.5 times the working pressure, non-shock cold water.

*Burst pressure is engineered minimum 2 times the working pressure.

MATERIAL SPECIFICATIONSHousing:

ASTM A 395, Gr. 65-45-15, min. tensile strength 4481 Bar (65,000 psi).

Surface Finish:

red.

(Option)

Rubber Gasket:

(Colour code: Green stripe) Good for cold & hot water up to 110°C (230°F). Also good for services for water with acid, water with chlorine, deionized water, seawater and waste water, dilute acids, oil-free air and many chemicals. Not recommended for petroleum oils, minerals oils, solvents and aromatic hydrocarbons. Maximum Temperature Range: -34°C to 110°C (-30°F to 230°F)*. * EPDM gaskets for water services are not recommended for steam services unless couplings or components are accessible for frequent gasket replacement.

(Colour code: Orange stripe) Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Also good for water services under 66°C (150°F). Temperature range: -29°C to 82°C (-20°F to 180°F). Do not use for HOT WATER above 66°C (150°F) or HOT DRY AIR above 60°C (140°F)

Grade “L” - Silicone.

For additional details contact Shurjoint.

Bolts & Nuts:

ASTM A 449-83a (or A 183 Gr. 2), minimum tensile strength 7584 Bar (110,000 psi), Zinc electroplated, with heavy-duty hexagonal nuts to ASTM A 563.

1 0/q r sr q r tq s ur q r t


GROOVED COUPLINGS

Grooved

Couplings

37

Electrical Continuity

Test pipe at TÜV Rheinland®

Couplings in Galvanised FinishMost GRINNELL Grooved Couplings in galvanised finish comply to the electric conductivity according to clause 11.1.2 of EN 61537-2007. Tests were performed by TÜV Rheinland® and test reports are available upon request.

Part Number

Suitable for size Coupling

Inches

ApproxWeightkg

CLIP0103� W $ � � � � !

CLIP0406% W � � � � � !

CLIP0812& W � # � � � � !


Couplings in Painted FinishEarth bonding of the GRINNELL couplings in painted finish can be made in steel pipework systems with an electrical continuity clip. This clip, manufactured from 301-grade stainless steel, is designed to ensure electrical continuity in situations of high current loading and/or corrosive environments, providing equipotential bonding of the conductive parts. It is recommended that the pipework is assembled and installed as recommended and that

the pipework is bonded to the electrical earth and tested in accordance with the I.E.E. regulations for bonding (earthing). Installation should be regularly checked for equipotential bonding (earthing) in case of accidental damage or unauthorised pipework modifications. Following any future modification, electrical continuity clips must be used and the installation re-tested for equipotential bonding.

v w n / x y / v w n / x y /

www.grinnell.com

GROOVED COUPLINGS

Grooved

Couplings


These installation instructions do not take the place of nor do they eliminate the need for the installer to fully read and understand the complete GRINNELL Products Installation Handbook (refer to IH-1000M). Always review the GRINNELL Products Installation Handbook and individual product tech data sheets for the latest instructions, techniques, and care and maintenance information. This document does not supersede or replace the GRINNELL Products Installation Handbook or individual product tech data sheets. Current documentation can be obtained by contacting your GRINNELL sales Representative or visiting www.grinnell.com.

GRINNELL Coupling Installation InformationInstallation Handbook: IH-1000M

WARNING

Failure to follow these instructions may result in improper product installation, joint failure or leakage, serious per-sonal injury, and/or property damage.

The following instructions should be used as a guideline for the proper installation of GRINNELL Grooved Products.

1. Always read and understand the instructions.

2. To avoid serious personal injury always wear appro-priate personal protective equipment (ppe), such as safety glasses, hard hat and foot protection.

3. Never remove any piping component without verifying that the system is de-pressurized and drained. Failure to due so may result in serious personal injury.

4. Ensure that the supplied gasket is suitable for the in-tended application. To prevent deterioration of the gasket material, a petroleum lubricant should never be used. Use a recommended lubricant to install the gasket.

5. The pipe groove dimensions must be in accordance with Standard Roll Groove or Cut Groove Specifica-tions. Refer to Pages 221 to 232 or Tech Data Sheet G710 for additional information.

*Note: The samples that were tested contained the GRINNELL Figure 707 high pressure flexible couplings, and the GRINNELL Figure 260 end caps of the appropriate size. These were used on the assembly to test system components as related in a field environment. The rated or working pressure of these items is 68.9 bar (1,000 psi)

*Note: The material of both the fittings and couplings used in this testing is found on page nine of the GRINNELL Handbook. This material is Ductile Iron Casting Grade 65-45-12, which has an elongation in 51mm (2”) of 12%.

The Component Proof Test in ASME A17.1 – 2004, section 3.19.1.3 requires testing to section 8.2.8.5, or five times the rated pressure.

The calculation of the factor of safety located in section 8.2.8.5 would then be calculated as F = (5.04 / 12 – 2.8) + 2.7. This then, according to section 8.2.8.5, would be a requirement safety factor of 3.25. The minimum pressure requirement of these components then would be 224.1 bar (3,250 psig)

ASME Standard Note

6. Ensure that the coupling keys are engaged in the grooves.

7. Always tighten nuts evenly by alternating sides. Un-even tightening can cause the gasket to pinch or bind. If a gasket becomes pinched, replace it immediately.

8. Torque values are supplied as a guideline and may be used when setting the torque on power impact wrench-es. Always refer to the power impact wrench manufac-turer’s instructions for settings.

9. Exceeding the suggested torque values may cause damage to the coupling and/or result in pipe-joint fail-ure. Minimum bolt torque is required for coupling to meet the published performance parameters.

10. Always inspect each joint to ensure that the coupling is properly installed.

EPDM, Tri-Seal gaskets are recommended for freezer applications. Reducing Couplings are not recommended for freezer applications. For dry pipe and freezer applications, use the Tri-Seal freezer gasket with a petroleum-free silicone lubricant. Standard lube is not recommended for this application as it freezes and can cause leakage.

mechanical catalog 2013 - grinnell.hu - grinnell hornyos ... · 125 139.7 51.7 79.26 4.8 178.3...

Documents