mid project seminar
TRANSCRIPT
-
8/2/2019 Mid Project Seminar
1/12
ZONE SPEED LIMITATION OF COMMERICALVEHICLE
Under guidance ofMrs ARCHANA H.R
Mr CHETHAN KUMAR
NISH KUMAR- 1SG08EC007NKUSH KUMAR- 1SG08EC009
PRASOON- 1SG08EC048
RANJAN JHA- 1SG08EC059
-
8/2/2019 Mid Project Seminar
2/12
Contents
1. Introduction
2. Block Diagram
3. Working
4. Hardware used
5. Flowchart
6. Current Status
7. Planning & Goals
8. Tentative completion time
2Dept. of ECE, SCE, Bangalore
-
8/2/2019 Mid Project Seminar
3/12
Introduction
The aim is to build a sensor system for infrastructure to vehicle (I2V)communication,
transmit the information provided by active signals placed on the roadto adapt the vehicles speed and prevent collisions.
By active signals we mean ordinary traffic signals that incorporate long-
range active RFID tags with information stored into them. This information is collected in real time by RFID receiver module
placed onboard of the vehicle
A microcontroller, then compares the speed measured by the sensorwith information provided by the I2V infrastructure and allows the
efficient adaptation of the speed of the vehicle to the circumstances ofthe road
motor-screw pair jam the vehicles accelerator pad and apply brake toreach and maintain a given target speed.
Dept. of ECE, SCE, Bangalore 3
-
8/2/2019 Mid Project Seminar
4/12
Block Diagram
Dept. of ECE, SCE, Bangalore 4
-
8/2/2019 Mid Project Seminar
5/12
Working: Every vehicle will be having one unique RFID tag
The zone speed limit info will be stored in the database of road infrastructureinstalled on road side and constantly send .
The receiver tag on the vehicle receives and decodes the signal and extract the info.
The speed sensor measures the speed and gives this info to MCU through ADC
The above two variables is compared and decisions are made by the MCU
If speed is higher than the limit MCU sends ctrl signals to jam the accelerator padthrough stepper motor
Simultaneously a braking system operates to reduce the speed slowly to avoidaccident
If the speed is equal or less no action is taken.
Dept. of ECE, SCE, Bangalore 5
-
8/2/2019 Mid Project Seminar
6/12
FLOW CHART
Dept. of ECE, SCE, Bangalore 6
-
8/2/2019 Mid Project Seminar
7/12
Hardware Used: Microcontroller- Atmel ATMega32
RFID Reader & tag unit- 900 KHz
RS 232 IC
H bridge
Stepper Motor
Regulator
Power supply
Dept. of ECE, SCE, Bangalore 7
-
8/2/2019 Mid Project Seminar
8/12
Current Status: Hardware-
1. uC development board is ready.
2. Most components are procured.
Software code for following actions is completed:
1. LCD display of speed
2. Motor rotating code
Dept. of ECE, SCE, Bangalore 8
-
8/2/2019 Mid Project Seminar
9/12
Planning & Goals: We plan to complete the program for receiving signals and
comparing the data operation in next phase.
Braking system deployment will be completed in next phase.
Then debugging of the programs will be done.
Finally the hardware & software will be integrated together.
Dept. of ECE, SCE, Bangalore 9
-
8/2/2019 Mid Project Seminar
10/12
Tentative completion time: Programming expected to be complete in next 6-7 days
Testing of project for proper working and debugging 6 to7 days.
Final project is expected to be ready in 10 to 15 days.
Dept. of ECE, SCE, Bangalore 10
-
8/2/2019 Mid Project Seminar
11/12
THANKYOU
Dept. of ECE, SCE, Bangalore 11
-
8/2/2019 Mid Project Seminar
12/12
Dept. of ECE, SCE, Bangalore 12