office partitions iii · h14 1-800-645-2986 office partitions assembly instructions h6 h13 (2) (4)...
TRANSCRIPT
Office Partitions
AssemblyInstructions
Customer Service1-800-645-2986
Low-Hi (90 )̊3 - Way Connector Straight Extension
Hi-Low (90 )̊Right/Left Connector 90˚ Connector S c r e w
Adjust all levelers toapproximately 1-1/4”
H7
HARDWARE
A S S E M B LY• Configurations require the correspondingsteps needed for proper assembly.
• Attach appropriate brackets or legs onthe ends of the panels as needed.
• Panels must be level. Level each panel.• Do not attach bolts or brackets into theoutermost edge of a panel that will be lastin line.
• Starter panel should use a corner, 3-way,4 - w a y, or wall bracket.
• Insert bolt cap into unused threadedinsert to finish your project.
• Level each panel as you go along.
H8 H9 H10 H11
Panel Filler Cap Panel Filler PostHex Bolt Threaded Stud Bolt Cap
H13 H14 H15 H16 H17
Toggle Bolt
H12
1
Straight Connector 3-way ConnectorWall BracketRight A n g l e
(90˚) Connector 4-way Connector
H1 H2 H3 H4 H5
T- L e g
H6
WARNINGIn order to prevent structural failure, instability,t i p - o v e r, and/or serious injury, please followi n s t ructions care f u l l y. Do not use hanging shelf oro v e rhead cabinet with panels that have glass.
• Use only the instructions, parts andhardware included
• Maximum span for connectedpanels without support is 12 feet
• Do not move panels while they are connected together• Maximum span for connectedpanels using overhead cabinets orshelves without support is 12 feet
• Requires 2 people for assembly• Not for outdoor or high humidity areas
12’ 12’
12’ 12’
O v e r h e a dC a b i n e t s
O v e r h e a dS h e l v e s
Assembly Instructions1-800-645-2986Office Partitions
2
Go To“ A ”
Go To“ B ”
Go To“ C ”
Go To“ D ”
Go To“ E ”
Go To“ F ”
Go To“ G ”
Go To“ I ”
Go To“ J ”
Go To“ H ”
Assembly Instructions1-800-645-2986
3
Office PartitionsA
(2) (4)
Note: Hardwareto anchor wallbracket to wall isnot provided.
P1
H1
H13
H1 H13
B
P1
H13
H2
Loosely attach
top bolts
P2
P2
P2
P1
P1
STEP 1
STEP 2
STEP 3
STEP 4
Fit panel
studs into
bottom
bracket,
then loosely
attach to
top bracket
Insert panelfiller caps intopanel fillerpost top andbottom. Insertpost intobottombracket first,then into topbracket. Thentighten allbolts firmlyH16
H15
H2
H13
Foam seal may
need to be trimmed
to fit panel
H1
H13
H14
H2 H13 H14 H15 H16
(2) (6) (2) (2) (1)
P1
Start at
wall and
level
panel
Assembly Instructions
STEP 2
P1
P1
1-800-645-2986
4
Office PartitionsC
D
P2
STEP 2
Loosely attach
top boltsSTEP 1
STEP 3
P1P2
Loosely attach
top bolts
STEP 3
P1
P2P3
Fit panel studs into
bottom bracket, then bolt
and tighten top bracket
Fit panel studs
into bottom
bracket, then
loosely attach
to top bracket
STEP 4
P2P3
H4
H13
H14
H14
H13
H3
H3
H13
I n s e rt panel fillercaps into panelfiller post top andbottom. Insertpost into bottombracket first, theninto top bracket.Then tighten allbolts firm l y
STEP 1
H15
H16
Foam seal may
need to be trimmed
to fit panel
H3 H13 H14
(2) (6) (2)
P2P3
H4 H13 H14 H15 H16
(2) (8) (4) (2) (1)
H13
H4
P1
H14
Assembly Instructions1-800-645-2986Office Partitions
H6 H13
(2) (4)
P1
E
F
P2P3P4
STEP 2
H5
H13
H6
H6
H13
STEP 3
STEP 4
Fit panel studs
into bottom
bracket, then
loosely attach
to top bracket
Fit panel studsinto bottombracket first,then into topbracket. Thentighten allbolts.
P2P3 P1
P2
P3
P4
Loosely attach
top bolts
Remove
both levelers
and discard
P1
5
H5 H13 H14
(2) (10) (6)
H5
H13
Assembly Instructions
P1
1-800-645-2986
G
P2
STEP 2
STEP 1
H3
H13
Office Partitions
P1
P2
STEP 3
H13
H8
STEP 4
H3 H8 H11 H13 H14
(1) (1) (2) (6) (2)
Fit panel studs intopanel bracket.
Align panel to bracket and screwin using 2 self tapping screwsand washers (H11) until tight(do not overtighten).
Foam seal mayneed to betrimmed tofit panel.
Bolt and tighten topbracket H8 onto panel 2.
H14
P1
P2
6
H11
Assembly Instructions
P1
1-800-645-2986
7
Office PartitionsH
P2P3
STEP 2
Loosely attach
top bolts.STEP 1
STEP 3
P1P2Insert panel filler
caps into filler post
top and bottom.
Insert post into
bottom bracket.
Fit panel studs into
bottom bracket,
then bolt and
tighten top bracket.
H13
H10
H4 H8 H10 H12 H13 H14 H15 H16
(1) (1) (1) (2) (8) (4) (2) (1)
P1
P1P3
P2
P2
P3
STEP 4
STEP 5
STEP 6
H8 H12
H16
Assembledpanels P1and P2.
Bolt on topbracket H8 toshort panel 3.
DO NOT FORCE DRILL
WARNING
H14
H14
TOGGLE BOLT (H12) A S S E M B LY I N TO FILLER POST
31 2
H15H16
Follow toggle
bolt assembly
diagram.
Fit panel studs into bottom
bracket first, then mark position
of vertical holes on filler post.
Drill holes where
marked from
previous Step 5.
H13
H13
H4
H8 H16
Assembly Instructions1-800-645-2986Office Partitions
8
I - Right
H2
H2 H7 H11 H13 H14 H15 H16
(1) (2) (2) (4) (2) (2) (1)
P1
P2
P1
P2 P2
P1
H15H16
STEP 1
STEP 3
STEP 4H13
H7STEP 2
Insert panel fillercaps into panelfiller post top andbottom. Insertpost into bottombracket first, theninto top bracket.Then tighten allbolts firmly
Align panel to bracketand screw in using 2 selftapping screws andwashers (H11) until tight(do not overtighten).
Loosely attachtop bolts.
H14
I - Left
H2
P2
P1
P2
P1
H15
H16
STEP 1
STEP 3
STEP 4H13
H7STEP 2
Insert panel fillercaps into panelfiller post top andbottom. Insertpost into bottombracket first, theninto top bracket.Then tighten allbolts firmly
Align panel to bracketand screw in using 2 selftapping screws andwashers (H11) until tight(do not overtighten).
Loosely attachtop bolts.
H14
P1
P2 H11
H11
Assembly Instructions1-800-645-2986Office Partitions
9
J
P1
P1
P1
P2P3
P2
P2P3
P3
P3H4
H13
H13 H9
H9
H9
H13
STEP 1
STEP 3
H4 H9 H11 H13 H14 H15 H16
(2) (1) (2) (6) (4) (2) (1)
H15H16
Looselyattachtop bolts
STEP 4Insert panel filler capsinto panel filler posttop and bottom
STEP 5Insert post intobottom bracketfirst. Fit panelstuds into bottombracket thenattach bracket topanel 2. Tightenbolts
STEP 6Align panel 1 tobracket and screwin self tappingscrews andwashers H11 intoside of panel 1.
H11
H16
STEP 2
H14
Assembly Instructions1-800-645-2986Office Partitions Layout
10012014