ota105204 optix osn series ethernet services configuration(manual configuration) issue 1.21

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

www.huawei.com

Internal

OptiX OSN Series Ethernet Services Configuration (Manual Configuration)

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved

Upon completion of this course, you will be

able to:

Explain the menu of iManager T2000 for

Ethernet Services

Describe the process of configuring

Ethernet Services on the T2000

Learn how to configure Ethernet Services


Chapter 1 The Basic ConceptsChapter 1 The Basic Concepts

Chapter 2 The EPL Service Configuration Chapter 2 The EPL Service Configuration

Chapter 3 The EPLAN Service ConfigurationChapter 3 The EPLAN Service Configuration

Chapter 4 The EVPL Service ConfigurationChapter 4 The EVPL Service Configuration


Tag flag is used to identify the type of packets. Three types of TAG flags are available: tag aware, access, and hybrid.

Tag Aware: When the port is set to be tag aware, the port transmits the packets with the Tag flag transparently and discards those without the Tag flag

Access: When the port is set to be access, the port attaches a Tag flag to the packets without Tag flag according to its VLAN ID and discards those with the Tag flag.

Hybrid: When the port is set to be hybrid, the port can process packets regardless of the Tag flag and attach a Tag flag to the packets without the Tag flag according to its VLAN ID.

Tag flag:

Parameters for the Ethernet interface



Tag flag Untag flag

Tag aware (In) Transmit transparently discard

Tag aware (Out) Transmit transparently －

Access (In) discard attach a Tag flag (default Vlan)

Access (Out) Delete the Tag flag (default Vlan) －

Hybrid (In) Transmit transparently attach a Tag flag (default Vlan)

Hybrid (Out)If Vlan is the same, delete the Tag flag,

otherwise transmit transparently－

PortPackets



VLAN ID:

VLAN ID of the port (MAC or VCTRUNK).

Working mode:

It can be set to auto-negotiation, 10 Mbit/s half/full-duplex, 100 Mbit/s half/full-duplex or 1 Gbit/s full-duplex. The Ethernet interfaces of the interconnected equipment should work under the same fixed working mode; otherwise, the packet may be lost and the rate may decrease, or the service may be completely interrupted upon large volume of traffic.

Port type:

There are two types: P and PE. Provider edge (PE) is the marginal port of the service provider. Provider (P) is the core network port of the service provider. Port type is needed when configuring EVPL and EVPLAN services.



LCAS enable:

Maximum packet length:

Whether to enable LCAS.

Set this item for the external port, 1522 bytes by default.

Mapping protocol:

It is preferable to select the default- GFP mapping protocol.


Reference: G.8010 /Y.1306 (G.ethna),

G.8011 (G.ethsrv),

G.8012.1 (G.eota.1).

Ethernet Services Types

EPL: Ethernet Private Line Service.

EPLAN: Ethernet Private LAN Service .

EVPL: Ethernet Virtual Private Line Service.

EVPLAN: Ethernet Virtual Private LAN Service.


For EPL Service, there are three types:

the Point-to-Point EPL Service

the MAC Shared EPL Service

the VCTRUNK Shared EPL Service

Configuring the EPL ServiceConfiguring the EPL Service


Configuring the EPL Service

Configuring the Point-to-Point EPL Service:

Engineering Requirements

Engineering Planning

Configuration Process




User Service requirement Source station Sink station Bandwidth

A Point-to-point NE1 NE5 10 Mbit/s

B Point-to-point NE1 NE5 40 Mbit/s

STM-16 two-fiberbidirectional MSP ring

T2000

STM-4 two-fiberbidirectional non-protection chain

NE1

NE2

NE3

NE4

NE5






− Step 1: Networking Diagram

− Step 2: Board Information of Each NE

− Step 3: Service Configuration Diagram of Each NE

− Step 4: Timeslot Allocation Diagram


A B


T2000


NE1

NE2

NE3

NE4

NE5

A BVC-Trunk

MAC1 MAC2

MAC1 MAC2

Company A Service

Company B Service




Board layout of NE1 Board layout of NE1




Board layout of NE5 Board layout of NE5


−Step 2: Board Information of Each NE


VC4-4:VC12-1~VC12-5

MAC1A

10M

40MB

VCTRUNKMAC

MAC2

VCTRUNK1

VCTRUNK2VC-4-1:VC-3-1

SDHVC4-4:VC12-1~VC12-5

VCTRUNK

VCTRUNK1

VCTRUNK2VC-4-1:VC-3-1

MAC1A

10M

40MB

MAC

MAC2

NE1NE5

Service configuration diagram





Service Attribute A B

Source NE NE1 NE1

Source board - port 13-N1EFS4-1 13-N1EFS4-2

Source timeslot VC4-4: VC12-1–VC12-5 VC4-1: VC3-1

Source VCTRUNK VCTRUNK1 (Tag aware) VCTRUNK2 (Tag aware)

Working mode of source MAC port Auto negotiation Auto negotiation

TAG flag of source MAC port Access Access

VLAN ID of source MAC port 1 2

Bound bandwidth 5 x VC-12 1 x VC-3

Sink NE NE5 NE5

Sink board - port 15-N1EFS4-1 15-N1EFS4-2

Sink timeslot VC4-4: VC12-1–VC12-5 VC4-1: VC3-1

Sink VCTRUNK VCTRUNK1 (Tag aware) VCTRUNK2 (Tag aware)

Working mode of sink MAC port Auto negotiation Auto negotiation

TAG flag of sink MAC port Access Access

VLAN ID of sink MAC port 1 2




Timeslot

NE2Station NE3 NE4NE112-SL16-1

NE17-SL16-112-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1

Forward

NE5NE4

13-SL4-1 7-SL4-1

Ring

Chain

Add/Drop

VC-4-313-EFS4: VC4-4

VC-12: 1-5

VC-4-4 13-EFS4: VC-4-1

VC-3: 1

VC-4-3

VC-4-4

15-EFS4: VC4-4

VC-12: 1-5

15-EFS4: VC-4-1

VC-3: 1

Station






− Step 1: Creating a board

− Step 2: Configuring Ethernet interfaces

− Step 3: Configuring binding paths

− Step 4: Creating the point-to-point EPL service

− Step 5: Configuring committed access rate (CAR)

(Optional )

− Step 6: Configuring the cross-connect from Ethernet

boards to SDH line boards




Right click


Configuring the EPL Service− Step 2: Configuring Ethernet interfaces

Right click

Left click

Left click


Configuring the EPL Service− Step 3: Configuring binding paths

Left click

Left click

Left click

Left click



− Step 4: Creating the point-to-point EPL service

Left clickLeft click



Left click

− Step 4: Configuring committed access rate (CAR) (Optional )

Left click


Configuring the EPL Service Step 6: Configuring the cross-connect from Ethernet boards to SDH line boards

Left click Left clickLeft click


Summary

Creating an Ethernet board

Configuring Ethernet interfaces

External Port: Basic Attributes, Tag Attribute

Internal Port: Tag Attribute, LCAS

Configuring binding paths:

Configurable Ports, Level, Direction, Available VC4, timeslots

Creating the MAC shared EPL service:

Service Type, Service Direction, Ports, VLAN, TAG, Port Type

Configuring committed access rate (CAR):

CAR ID, Capacity, Ports

Configuring the cross-connect from Ethernet boards to SDH line boards



Configuring the MAC Shared EPL Service :






T2000


NE1

NE2

NE3

NE4

NE5



Configuring the MAC Shared EPL Service:

Source User Service requirement Source station Sink User Sink station Bandwidth

C MAC Shared NE1 C(1) NE5 10 Mbit/s

C MAC Shared NE1 C(2) NE5 10 Mbit/s




Configuring the MAC Shared EPL Service :






T2000NE1

NE2

NE3

NE4 NE5A B

A BVC-Trunk

MAC1 MAC2

MAC1 MAC2

MAC3 MAC4

C(2)C(1)

C (Headquarters)

MAC3

C & C(1) Service

C & C(2) Service







▪ NE1 and NE5 do not require any new board.




Service Attribute C & C(1) C & C(2)

Source NE NE1

Source board - port 13-N1EFS4-3

Source timeslot VC4-4: VC12-6–VC12-10 VC4-4: VC12-11–VC12-15

Source VCTRUNK VCTRUNK3 (Tag aware) VCTRUNK4 (Tag aware)

Working mode of source MAC port Auto negotiation Auto negotiation

TAG flag of source MAC port Tag aware Tag aware


Bound bandwidth 5 x VC-12 5 x VC-12

Sink NE NE5

Sink board - port 15-N1EFS4-3 15-N1EFS4-4

Sink timeslot VC4-4: VC12-6–VC12-10 VC4-4: VC12-11–VC12-15

Sink VCTRUNK VCTRUNK3 (Tag aware) VCTRUNK4 (Tag aware)





Timeslot

NE2Station NE3 NE4NE1

12-SL16-1

NE1

7-SL16-112-SL16-17-SL16-112-SL16-17-SL16-112-SL16-1 7-SL16-1

Forwared

NE5StationNE4

13-SL4-1 7-SL4-1

Ring

Chain

Add/Drop

VC-4-313-EFS4: VC4-4

VC-12: 6-15

VC-4-315-EFS4: VC4-4

VC-12: 6-15




Notice: We don’t need the first step because the Ethernet boards

Have already been created.


Configuring the MAC Shared EPL Service:


− Step 1: Creating a board (None)



− Step 4: Creating the MAC shared EPL service

− Step 5: Configuring committed access rate (CAR) (Optional

Step 6: Configuring the cross-connect from Ethernet boards

to SDH line boards


Configuring the EPL Service− Step 2: Configuring Ethernet interfaces

Right click

Left click

Left click



Left click

Left click

Left click

Left click



Left click


Left click

− Step 4: Creating the MAC shared EPL service


Notice: These two steps are the same as that of the

point-to-point EPL service, except that some

parameters are different.


Step 5: Configuring committed access rate (CAR) (Optional

Step 6: Configuring the cross-connect from Ethernet boards to

SDH line boards


Summary

Creating an Ethernet board Configuring Ethernet interfaces

External Port: Basic Attributes, Tag Attribute

Internal Port: Tag Attribute, LCAS Configuring binding paths:

Configurable Ports, Level, Direction, Available VC4, timeslots Creating the MAC shared EPL service:

Service Type, Service Direction, Ports, VLAN, TAG, Port Type Configuring committed access rate (CAR):

CAR ID, Capacity, Ports Configuring the cross-connect from Ethernet boards to SDH line boards



Configuring the VCTRUNK Shared EPL Service :






T2000STM-4 two-fiberbidirectional non-protection chainNE1

NE2

NE3

NE4

NE5



Configuring the VCTRUNK Shared EPL Service:

Source

User

Service

requirement

Source

station

Sink User Sink

station

Bandwidth

D VCTRUNK Shared NE2 D’ NE3 300 Mbit/s

E VCTRUNK Shared NE2 E’ NE3 300 Mbit/s



Configuring the VCTRUNK Shared EPL Service :







T2000

NE1

NE2

NE3

NE4

NE5

D

B

VC-Trunk

MAC1

MAC2

MAC2MAC1

E

D’ E’ D & D’ Service

E & E’ Service





− Step 2: Board Information of Each NEBoard layout of NE2 and NE3


MAC1D

300M

E

VCTRUNKMAC

MAC2

SDHVC4-1:VC3-1~VC3-3VC4-2:VC3-1~VC3-3

VCTRUNK

VCTRUNK1

MAC1D’

E’

MAC

MAC2

NE2 NE3

300M

300M

300MVC4-1:VC3-1~VC3-3VC4-2:VC3-1~VC3-3

VCTRUNK1






Service Attribute D E

Source NE NE2

Source board - port 13-N1EGS2-1 13-N1EGS2-2

Source timeslot VC4-1: VC3-1–VC3-3, VC4-2: VC3-1–VC3-3

Source VCTRUNK VCTRUNK1 (Tag aware)

Working mode of source MAC port 1000M full duplex 1000M full duplex

TAG flag of source MAC port Access Access


Bound bandwidth 6 x VC-3

Sink NE NE3

Sink board - port 13-N1EGS2-1 13-N1EGS2-2

Sink timeslot VC4-1: VC3-1–VC3-3, VC4-2: VC3-1–VC3-3

Sink VCTRUNK VCTRUNK1 (Tag aware)

Working mode of sink MAC port 1000M full duplex 1000M full duplex




Notice: The steps are the same as the MAC shared EPL Service.

So here we don’t need introduce them again.


Configuring the VCTRUNK Shared EPL Service:


− Step 1:Creating a board



− Step 4: Creating the VCTRUNK shared EPL service


Step 6: Configuring the cross-connect from Ethernet boards to

SDH line boards


Summary


External Port: Basic Attributes, Tag Attribute Internal Port: Tag Attribute, LCAS

Configuring binding paths: Configurable Ports, Level, Direction, Available VC4, timeslots

Creating the VCTRUNK shared EPL service: Service Type, Service Direction, Ports, VLAN, TAG, Port Type

Configuring committed access rate (CAR): CAR ID, Capacity, Ports



Configuring the EPLAN Service

Configuring the EPLAN Service:






T2000STM-4 two-fiberbidirectional non-protection chainNE1

NE2

NE3

NE4

NE5

Configuring the EPLAN Service Engineering Requirements

Source User Service requirement Source station Sink User Sink station Bandwidth

F(1) EPLAN NE2 F(2) NE3 10 Mbit/s




T2000

NE1

NE2

NE3

NE4

NE5

B

VC-Trunk

MAC1

MAC1

F(1)

F(2)

MAC1

F(3)

VB

MAC1

VCTRUNK1

MAC1

VCTRUNK2VCTRUNK1 VB

VB

MAC1

VCTRUNK1

F(1) & F(2) Service

F(3) & F(2) Service

F(1) & F(3) Service

Configuring the EPLAN Service− Step 1: Networking Diagram


Board layout of NE2 and NE3






Board layout of NE4


Service configuration diagram Service configuration diagram

MAC1F2

10M

VCTRUNKMAC

SDH

VC4-4:VC12-1~VC12-5

VCTRUNK

VCTRUNK1

MAC1F1

MAC

NE3

NE2

10M

VC4-4:VC12-1~VC12-5VCTRUNK1

VB1

LP1LP2

LP3

VCTRUNK2VC4-4:VC12-6~VC12-10

VB1

VC4-4:VC12-1~VC12-5

VCTRUNK

VCTRUNK1

MAC1F3

MAC

NE4

10M

VB1

LP1

LP1

LP2

LP2

Configuring the EPLAN Service− Step 3: Service Configuration Diagram of Each NE


Configuring the EPLAN ServiceAttribute \ Service F

Source NE NE3

Source board – port 14-N1EFS0-1

Source timeslot VC4-4: VC12-1–VC12-5 VC4-4: VC12-6–VC12-10

Source VCTRUNK VCTRUNK1 (Tag Aware) VCTRUNK2 (Tag Aware)

Source VCTRUNK attribute PE PE

Working mode of source MAC port Auto negotiation

TAG flag of source MAC port Access

VLAN ID of source MAC port 11

VB VB1

Attached port MAC1, VCTRUNK1, VCTRUNK2

Sink NE NE2 NE4

Sink board – port 14-N1EFS0-1 15-N1EFS0-1

Sink timeslot VC4-4: VC12-1–VC12-5 VC4-4: VC12-1–VC12-5

Sink VCTRUNK VCTRUNK1 (Tag Aware) VCTRUNK1 (Tag Aware)

Sink VCTRUNK attribute PE PE




Virtual bridge (VB) VB1 VB1

Attached port MAC1, VCTRUNK1 MAC1, VCTRUNK1





NE name VB VLAN ID Forwarding port

NE2 VB1 11 LP1, LP2

NE3 VB1 11 LP1, LP2, LP3

NE4 VB1 11 LP1, LP2







− Step 4: Creating the EPLAN service

− Step 5: Configuring the forwarding filter table


− Step 7: Configuring the cross-connect from Ethernet boards to

SDH line boards


Configuring the EPLAN Service− Step 2: Configuring Ethernet interfaces

Right click

Left click

Left click


Left click


Left click

Left click

Left click

− Step 3:

Configuring

binding paths


Left click

Configuring the EPLAN Service− Step 4: Creating the EPLAN service

Left click

Left click

Left click

Left click


Configuring the EPLAN Service− Step 5: Configuring the forwarding filter table

Left click

Left click

Left click


Configuring the EPLAN Service− Step 6: Configuring committed access rate (CAR) (Optional )

Left click

Left click


Configuring the EPLAN Service− Step 7: Configuring the cross-connect from Ethernet boards to SDH line

boards

Left click

Left clickLeft click


Summary


External Port: Basic Attributes, Tag Attribute, VLAN Internal Port: Tag Attribute, VLAN, LCAS

Configuring binding paths: Configurable Ports, Level, Direction, Available VC4, timeslots

Creating the EPLAN service: VB Port, Mount Port, Port Type, Binding Path

Configuring the forwarding filter table VB Port, VLAN ID, forwarding port

Configuring committed access rate (CAR): CAR ID, Capacity, Ports



Configuring the EVPL Service

Configuring the EVPL Service:






T2000 STM-4 two-fiber

bidirectional non-protection chainNE1

NE2

NE3

NE4

NE5

Configuring the EVPL Service Engineering Requirements

Source

User

Service

requirement

Source

stationSink User

Sink

stationBandwidth

D EVPL NE2 D’ NE3 100 Mbit/s

E EVPL NE2 E’ NE3 100 Mbit/s


T2000

NE1

NE2

NE3

NE4

NE5

D

B

VC-Trunk

MAC1

MAC2

MAC2MAC1

E

D’ E’D & D’ Service

E & E’ Service




Configuring the EVPL Service− Step 2: Board Information of Each NE

Board layout of NE2 and NE3




Attribute \ Service D ESource NE NE2Source board - port 14-N1EFS0-1 14-N1EFS0-2Source timeslot VC4-4: VC12-1–VC12-48Source VCTRUNK VCTRUNK1 (Tag Aware )Source VCTRUNK attribute PWorking mode of source MAC port 100M full duplex 100M full duplex TAG flag of source MAC port Tag Aware Tag AwareVLAN ID of source MAC port 11 11Source MAC attribute PE PEBound bandwidth 48 x VC-12Sink NE NE3Sink board - port 14-N1EFS0-1 14-N1EFS0-2Sink timeslot VC4-4: VC12-1–VC12-48Sink VCTRUNK VCTRUNK1 (Tag Aware )Sink VCTRUNK attribute PWorking mode of sink MAC port 100M full duplex 100M full duplexTAG flag of sink MAC port Tag Aware Tag AwareVLAN ID of sink MAC port 11 11Sink MAC attribute PE PE





NE name VCTRUNK-MAC

(path)

multi-protocol label switching (MPLS)

Tunnel VC

NE2 \ NE3 VCTRUNK1-MAC1 55 25

NE2 \ NE3 VCTRUNK1-MAC2 66 26

Station

Timeslot

NE1 NE2 NE3 NE4 NE1

12-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1

VC4-4

VC12: 1-48

14EFS0: VC4-4Forward

Add/Drop







Step 4: Creating the EVPL service

Step 5: Configuring committed access rate (CAR)

(Optional )




Configuring the EVPL Service− Step 2: Configuring Ethernet interfaces

Right click

Left click

Left click


Configuring the EVPL Service− Step 3: Configuring binding paths

Left click

Left click

Left click

Left click



− Step 4: Creating the

EVPL service

Left clickLeft click Left click


Notice: These two steps are the same as that of the EPL service, except that some parameters are different.


− Step 5: Configuring committed access rate (CAR)

(Optional )




Summary Creating an Ethernet board

Configuring Ethernet interfaces

External Port: Basic Attributes, Tag Attribute, VLAN

Internal Port: Tag Attribute, VLAN, LCAS, MPLS

Configuring binding paths:

Configurable Ports, Level, Direction, Available VC4, timeslots

Creating the EVPL service:

Service Type, Service Direction, Ports, TAG, VLAN, Tunnel, VC, Port

Type, Encapsulation Format

Configuring committed access rate (CAR):

CAR ID, Capacity, Ports

Configuring the cross-connect from Ethernet boards to SDH line

boards

www.huawei.com

Thank You

ota105204 optix osn series ethernet services configuration(manual configuration) issue 1.21

Documents

epl service step

pointtopoint epl service

service provider

rights reserved page

service configuration

mac shared epl service

tag flag access

ethernet private line