pcn 182 092041 00 - dragon's den · * this manual supersedes the m40a1 part of tm...

*TM 3-4240-346-20&PTM 09204A/09205A-20&P/2

UNIT MAINTENANCE MANUAL(INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST)

FOR

CHEMICAL BIOLOGICAL MASK: FIELD M40A1

(4240-01-370-3821-SMALL)(4240-01-370-3822-MEDIUM)(4240-01-370-3823--LARGE)

CHEMICAL BIOLOGICAL MASK: COMBAT VEHICLE M42A2

(4240-01-413-4100-SMALL)(4240-01-413-4101-MEDIUM)(4240-01-413-4102--LARGE)

* This manual supersedes the M40A1 part of TM 3-4240-300-20&P / TM 09204A/09205A-20&P/2, 31 July96, and the M42A2 part of TM 3-4240-343-20&P/TM 09204A/09205A-20&P/2, 31 July 96.

WARNING - This document contains export-controlled technical data whose export is restricted by the Army ExportControl Act (Title 22, U.S.S.S., Sec 2751 et seq.) or Executive order 12470. Violation of these export laws is subject tosevere criminal penalties.

DISTRIBUTION STATEMENT - Distribution authorized to U. S. Government agencies and their contractors toprotect technical or operational information This determination was made on 24 June 1987. Other requests for thisdocument will be referred to: Technical Director, U.S. Army, Edgewood Research, Development & Engineering Center,ATN: SCBRD-ENL-V, Aberdeen Proving Ground, MD 21010-5423.

DESTRUCTION NOTICE – Destroy by any method that will prevent disclosure of contents or reconstruction of thedocument.

HEADQUARTERS, DEPARTMENT OF THE ARMYAND, HEADQUARTERS, MARINE CORPS

1 AUGUST 1998

PCN 182 092041 00

WARNINGS point out dangerous steps in the procedures in this manual Your safety depends on following the instructionsincluded in all WARNINGS. Several general WARNINGS are included below:

• The mask will not be fully effective in confined spaces when the oxygen content of the air is too low. The CB maskhas only been tested and verified to protect against all known military agents.

• DO NOT touch your skin (or the soldier) with n-Amyl acetate (banana oil). It could irritate the skin. Wear rubbergloves.

• DO NOT smoke around n-Amyl acetate (banana oil), it is flammable.

• DO NOT test mask assembly with n-Amyl acetate (banana oil) in a closed, poorly ventilated area. Test outdoors or ina well-aired room, n-Amyl acetate may be toxic if inhaled in quantity.

• DO NOT wear contact lenses (soft or hard) while wearing CB Protective Masks. Inadequate oxygen supply to thecorneal surface, exposure to dust, dirt, and smoke/gas may cause serious vision loss or eye damage. Soldiersrequiring vision correction are provided optical inserts for their protective masks.

HEALTH/ENVIRONMENTAL HAZARD

• There are two Mask Filter Canisters, the C2 and the C2A1. The C2 canister contains Chromium VI and damaged orunusable canisters are considered Hazardous Waste. (Chromium VI is a known carcinogen if inhaled or swallowed.)

• The C2A1 canister is chromium-free but must continue to be disposed of in accordance with State and LocalEnvironmental Laws.

• DO NOT throw away damaged or unusable canisters as ordinary trash.

• DO turn in damaged or unusable canisters to your hazardous waste management office or Defense Reutilization andMarketing Office (DRMO).

FIRST AID

For first aid refers to FM 21-11.

SAFETY DATA SHEETS

http://www.apgea.army.mil/RDA/pmnbc/c2aldisp.html

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

TECHNICAL MANUAL

DEPARTMENT OF THE ARMYAND HEADQUARTERS, MARINE CORPS

Washington, D.C., 1 AUGUST 1998

UNIT MAINTENANCE MANUAL

(INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST)

FOR

CHEMICAL BIOLOGICAL MASK: FIELD M40A1

(4240-01-370-3821--SMALL)(4240-01-370-3822--MEDIUM)(4240-01-370-3823--LARGE)

CHEMICAL BIOLOGICAL MASK: COMBAT VEHICLE M42A2

(4240-01-413-4100--SMALL)(4240-01-413-4101--MEDIUM)(4240-01-413-4102--LARGE)

REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS

You can help improve this manual. If you find any mistakes or if you know of a way to improve the procedures, please let usknow. Mail you letter, DA Form 2028 (Recommended Changes to Publications and Blank Forms), or DA Form 2028-2located in the back of this manual direct to: Technical Director, U.S. Army, Edgewood Research, Development &Engineering Center, ATTN: SCBRD-ENL-V, Aberdeen Proving Ground, MD 21010-5423.

Marine Corps Users - Submit NAVMC FORM 10772 directly to Commander, Marine Corps Logistics Base (Code 850), 814Radford Blvd, AIbany, GA 31704-5000. In addition, a copy of the NAVMC 10772 or naval message should be sent toMARCORSYSCOM (Code CSLENBC), 2033 Barnett Ave., Suite 315, Quantico, VA 22134-5010.

In either case, a reply will be sent to you.

i

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

TABLE OF CONTENTS

HOW TO USE THIS MANUAL .................................................................................................................. iii

CHAPTER 1 INTRODUCTION.................................................................................................................. 1-1

SECTION I. GENERAL INFORMATION .................................................................................................. 1-1

SECTION II. EQUIPMENT DESCRIPTION AND DATA ............................................................................ 1-2

SECTION III. PRINCIPLES OF OPERATION ........................................................................................... 1-12

CHAPTER 2 UNIT MAINTENANCE INSTRUCTION ................................................................................. 2-1

SECTION I. REPAIR PARTS, SPECIAL TOOLS, TMDE, AND SUPPORT EQUIPMENT........................... 2-3

SECTION II. SERVICE UPON RECEIPT .................................................................................................. 2-3

SECTION III. EQUIPMENT/USER FITTING INSTRUCTIONS ................................................................... 2-19

SECTION IV. TROUBLESHOOTING ........................................................................................................ 2-29

SECTION V. PREVENTIVE MAINTENANCE CHECKS AND SERVICES .................................................. 2-39

SECTION VI. HOSE ASSEMBLY CONVERSION ..................................................................................... 2-45

SECTION VII. MAINTENANCE PROCEDURES ....................................................................................... 2-53

SECTION VIII. CLEANING AND SANITIZING ........................................................................................... 2-77

SECTION IX. PREPARATION FOR STORAGE OR SHIPMENT .............................................................. 2-95

APPENDIX A - REFERENCES ................................................................................................................ A-1

APPENDIX B - MAINTENANCE ALLOCATION CHART (MAC) ............................................................... B-1

APPENDIX C - UNIT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLSLIST......................................................................................................................... C-1

APPENDIX D - EXPENDABLE AND DURABLE ITEMS LIST .................................................................. D-1

CROSS-REFERENCE INDEXES ............................................................................................................. I-1

INDEX....................................................................................................................................................... INDEX 1

ii

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

HOW TO USE THIS MANUAL

The safest, easiest, and best way to do maintenance on the Chemical-Biological Mask, M40A1/M42A2 is to use this manual.Learning to use this TM is as easy as reading through the next few pages. Knowing what's in this manual and how to use itwill save you time and work, and will help you avoid exposing yourself to unnecessary hazards while you do your job.

ORGANIZATION

Page ii has a table of contents to provide easy access to the manual. Pages are numbered consecutively within eachchapter; each page number is prefixed with a chapter number or appendix letter. For example, page 5 of Chapter 2 isnumbered 2-5 and page 3 of appendix B is numbered B-3.

This manual is divided into two chapters, four appendixes, and an alphabetical index. Chapter 2 has an index at thebeginning of the chapter to provide easy access to its content. Each chapter is divided into sections. Chapter 1 containsgeneral information pertaining to location of forms, destruction of Army material, how to store and ship the mask, proceduresfor reporting any improvement recommendations you may have, as well as, corrosion prevention and control. Chapter 2gives unit maintenance instructions and includes four types of maintenance activities. These are: Service Upon Receipt;Troubleshooting or location of faults by symptoms you can detect; Preventive Maintenance Checks and Service (PMCS);and Maintenance Procedures that are used to correct faults and replace failed parts. Within the Troubleshooting andmaintenance portions of this manual, you will find the material in functional group code order like the Maintenance AllocationChart in Appendix B of this TM. This allows the TM to be aligned with its applicable Repair Parts and Special Tools List(RPSTL). For information on how to use the RPSTL, refer to the introduction in Appendix C.

Each section in this manual is further divided into three parts. The first addresses procedures which are the same regardlessof which mask you are using. The second part addresses those tasks which are peculiar to the M40A1 and the thirdaddresses those peculiar to the M42A2. Therefore, depending on which mask you are using, you must follow theinstructions in the general part and the part which is peculiar to your mask.

For instance, if you have the M40A1 mask, you must do the Before PMCS checks under COMMON and those checks listedunder M40A1 PECULIAR Those tasks listed under M42A2 PECULIAR are not required.

Those tasks which are considered to be COMMON and apply to either mask are illustrated using the M42A2.

However, the differences between the M40A1 and M42A2 do not impact on the task, and, in many cases, you willnot be able to tell from the illustration which mask is being illustrated.

HOW TO FIND PROCEDURES

If you're using the manual to perform Troubleshooting, go to Section IV, and read TROUBLESHOOTING PROCEDURESand proceed according to the instructions there. If you're going to do Scheduled Maintenance, you can turn directly toPreventive Maintenance Checks and Services (PMCS), Section V, and proceed according to the instructions there.

If you are using the manual to perform repair or replacement of a part that you already know is bad, you would start bylocating the part to be replaced in the Alphabetical index located at the back of this manual. Look in the Alphabetical Indexfor a key noun from the mask system or part nomenclature. The Alphabetical Index lists each task under one or moreheadings also giving the location for the installation and removal of some part. For example, the procedure for CLEANINGAND SANITIZING would be listed under "C" for Cleaning.

Once you've located the correct procedure, read through it to determine if you have everything you need to perform the job.Make sure all the Equipment Conditions have been met. Familiarize yourself with the potential hazards described by theWARNINGS and CAUTIONS. You must familiarize yourself with the entire maintenance procedure before beginning themaintenance task.

iii

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

HOW TO USE A MAINTENANCE PROCEDURE

The first page of a maintenance procedure lists everything you will need to perform that procedure. The followingparagraphs describe all the blocks of information you will find there.

TOOLS. Individual tools from your mechanic's tool kit will not be listed under this heading. If any tools from this kit arerequired, the tool kit itself will be listed as the first item. Special tools, and tools from any other source will be listed with areference to a specific item and appendix number. The referenced appendix will provide you with the necessary informationto find or make the tool.

SUPPLIES. If any expendable or consumable supplies are needed to perform the task, they will be listed under this headingalong with the quantity in parentheses and a reference to a figure item and appendix in the back of the TM. The referencedappendix will give you the detailed information necessary to requisition the supply if you don't have it on hand. Replacementparts are not normally listed under this heading. The inspection steps in the removal or disassembly procedure will tell youwhich parts to replace. Mandatory repair parts ( parts that are destroyed in disassembly or not normally reused, such asgaskets and lock washers) are listed under this heading by their nomenclature only. Refer to Repair Parts and Special ToolsList (RPSTL), Appendix C for information you need on repair parts.

iv (v blank)

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

CHEMICAL BIOLOGICAL MASKS

M40A1

M42A2

1-0

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

CHAPTER 1INTRODUCTION

SECTION I. GENERAL INFORMATION

1-1. SCOPE

a. Type of Manual. Unit maintenance.b. Model Numbers and Equipment Name. Chemical-biological (CB ) mask: field M40AI, and CB mask combat vehicle

M42A2.c. Purpose of Equipment. Protects the face, eyes, and lungs from field concentrations of CB agents, toxins, and

radioactive fallout particles.

1-2. MAINTENANCE FORMS, RECORDS, AND REPORTS

a. Department of the Army forms and procedures used for equipment maintenance will be those prescribed by DAPAM 738-750, The Army Maintenance Management System (TAMMS), as contained in the MaintenanceManagement update.

b. Marine Corps forms and procedures used for equipment maintenance are prescribed in TM 4700-15/1_.

1-3. DESTRUCTION OF ARMY MATERIAL TO PREVENT ENEMY USE

• Refer to TM 43-0002-31 for methods of destruction.

1-4. PREPARATION FOR STORAGE OR SHIPMENT

• Refer to Chapter 2, Section IX, for preparation for storage or shipment.

1-5. REPORTING EQUIPMENT IMPROVEMENT RECOMMENDATIONS (EIR)

a. If you have ideas on how the M40A 1 or the M42A2 masks can be changed or maintained more effectively, let usknow. Send us an EIR. You, the user, are the only one who can tell us what you don't like about your equipment. Letus know why you don't like the design. Put it on an SF 368 (Quality Deficiency Report). Mail it to us at Director, USArmy Armament and Chemical Acquisition and Logistics Activity, ATTN: AMSTA-AR-QAW-A (RI), Rock Island, IL61299-7630. We'll send you a reply.

b. Marine Corps users shall submit a Standard Form 368 (SF368) in accordance with MCO4855. 10 directly to:Commander, Marine Corps Logistics Base (Code 856), 814 Radford Blvd., Albany, GA 31704-5000. We will sendyou a reply.

1-6. CORROSION PREVENTION AND CONTROL (CPC)

a. CPC of Army material is a continuing concern. It is important that any corrosion problems with this item be reportedso that the problem can be corrected and improvements can be made to prevent the problem in future items.

b. While corrosion is typically associated with rusting of metals, it can also include deterioration of other materials suchas rubber and plastic. Unusual cracking, softening, swelling, or breaking of these materials may be a corrosionproblem.

c. If a corrosion problem is identified, it can be reported using a Quality Deficiency Report, SF 368. Use of key wordssuch as "corrosion", "rust", "deterioration", or "cracking" will assure that the information is identified as a CPCproblem.

d. The form should be submitted to Director, US Army Armament and Chemical Acquisition and Logistics Activity,ATTN: AMSTA-AR-QAW-A (RI), Rock Island, IL 61299-7630.

e. Marine Corps Units report CPC problems using SF 368 and procedures prescribed in TM 4700-15/1_.

1-1

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

SECTION II. EQUIPMENT DESCRIPTION AND DATA1-7. EQUIPMENT CHARACTERISTICS, CAPABILITIES, AND FEATURES.

COMMON

The lightweight, CB masks (M40A1 / M42A2 ) are easy to assemble for transport and storage. The mask assembly is keptdry, when required by climate and mission, by a waterproof bag and stored in a carrier made of mildew-resistant, waterrepellent, coated nylon.

The facepiece is made of silicone rubber with an inturned sealing surface so it can provide protection to face, eyes, andrespiratory tract from CB agents, toxins and radioactive particles. The mask assembly is not intended for use in an oxygendeficient environment. Nor is it intended to provide protection against carbon monoxide or ammonia It forms a comfortableseal on a soldier's face as it protects against adverse elements. The mask assembly is equipped with both front and sidevoicemitters for ease of communication and an outlet valve body with a drinking system. To ensure a comfortable fit, themask assembly is issued in three sizes: small, medium and large which are marked with S, M and L on the forehead toshow sizing. It is also equipped with clear and neutral gray outserts to protect the eyelens from scratches, reduce sun glareand prevent fogging in cold weather.

The masks have a second skin, universal second skin, or universal second skin (USMC) which fits to the facepiece andprotects the facepiece from liquid agents, and a quick doff hood made of lightweight, butyl rubber-coated fabric, whichprovides protection to the head and neck from liquid toxic chemical agents. The second skin, universal second skin, oruniversal second skin (USMC) is issued in two sizes: small and medium/large which are marked S and M/L on the exteriorleft cheek.

M40A1 PECULIAR

The CB mask, M40A1, consists of a facepiece and filter canister.

M42A2 PECULIAR

The CB mask, M42A2, consists of a facepiece, canister carrier and hose assembly . The M42A2 masks has microphonecommunication capability that can couple with on board communication systems, through the Combat VehicleCommunications (CVC) helmet.

1-8. LOCATION AND DESCRIPTION OF MAJOR COMPONENTS

COMMON

a. FACE PIECE ASSEMBLY

• FACEPIECE (1). The following components are molded/assembled into the silicone rubber facepiece: buckle tabs,facepiece openings for eyelens, nosecup, voicemitters, outlet valve, and filter canister/hose connectors.

• HEAD HARNESS (2). Constructed of elastic webbing sewn to a rectangular head pad and buckled to facepiece.The ends of the head harness straps have metal strap end clips to prevent fraying of the elastic webbing. Ends ofthe head harness straps pass through buckles at the two forehead, temple and cheek positions. Elastic webbingconnects the two forehead straps and holds them in proper alignment when the mask assembly is worn. Headharness straps attached to buckles at the ends of the tabs permit adjustment to obtain proper fit of the maskassembly.

1-2

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

• NOSECUP ASSEMBLY (3). Made of soft rubber, fits over the soldier's nose and mouth. Diverts exhaled air towardthe outlet valve to reduce fogging of the eyelens.

• NOSECUP VALVE SEATS (4). Each of two nosecup valve seats holds silicone rubber NOSECUP VALVE DISK (5),which allows filtered air to enter nosecup and prevent moist exhaled air from fogging the eyelens in cold weather.

• INTERNAL DRINK TUBE (6). Allows the soldier to drink while wearing the mask assembly.

• AIRFLOW DEFLECTOR (7), located inside the mask assembly, directs inhaled air over eyelens to reduce fogging.The airflow deflector also supports the inlet valve disk and the inlet valve body.

• INLET VALVE BODY (8) and INLET VALVE DISK (9), fits into the airflow deflector, allows filtered air to enter themask assembly and prevent moist exhaled air from entering the filter canister.

• OUTLET VALVE COVER (10). Protects outlet valve disk and outlet valve housing from damage.

• RETAINER (11). Holds external drink tube quick disconnect coupling.

• OUTLET VALVE DISK (12) and OUTLET VALVE HOUSING (13). Located behind outlet valve cover; releasesexhaled air and closes on inhalation to prevent contaminated air from entering mask assembly.

• FRONT (14) AND SIDE VOICEMITTERS (15). Transmits the soldier's voice outside the mask assembly.

• EXTERNAL DRINK TUBE (16). The External Drink Tube is used to connect the mask assembly to the M1 Canteencap for drinking. It consists of a length of hose and a quick disconnect coupling half (17) that fits into the externaldrink tube retainer.

• DURABILITY ENHANCEMENT BAND (18). Band placed around outlet valve housing to ensure seal is maintained.

1-3

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

1-8. LOCATION AND DESCRIPTION OF MAJOR COMPONENTS (CONT)

COMMON (CONT)

b. FILTER CANISTER (19) filters out CB agents and other particles from contaminated air.

NOTEThe soldier may be issued either the one piece hood OR the quick doff hood andsecond skin OR universal second skin and quick doff hood or hooded over-garment OR the universal second skin (USMC) and hooded overgarment. Theyare identical in function and effectiveness. However, the one piece hood may notbe removed during decon operations.

c. ONE PIECE HOOD (20). Provides protection to the head and neck against liquid toxic chemical agents encounteredin field operations. Made of lightweight butyl rubber-coated fabric. It is attached to the mask assembly during useand stowed in mask carrier.

1-4

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

d. QUICK DOFF HOOD.

• QUICK DOFF HOOD (21). Is made of butyl rubber-coated fabric, which protects area of neck and head that is notcovered by mask assembly against CB agents, toxins, and radioactive fallout particles.

• ELASTIC AROUND OPENING (22). Attaches quick doff hood to the second skin. It enables easy removal of thequick doff hood.

• ELASTIC AROUND NECK (23). Draws quick doff hood close to the neck to protect from CB agents.

• UNDERARM STRAPS (24). Retain quick doff hood on the shoulders. Plastic fasteners (25) are used to attach thestraps.

e. UNIVERSAL SECOND SKIN (26). Is made of butyl rubber and covers the mask assembly. It provides additionalprotection against liquid agents. (Rubber catches and ridges are no longer needed because the universal secondskin is now larger.)

• Interfaces with hooded overgarments.

• Extends beyond the mask assembly.

• Interfaces with QDH..

1-5

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

1-8. LOCATION AND DESCRIPTION OF MAJOR COMPONENTS--(CONT )

COMMON (CONT)

f. SECOND SKIN ( M40A 1/ M42A2).

• SECOND SKIN (27). Is made of butyl rubber, and covers the mask assembly. It provides additional protectionagainst liquid agents.

• RUBBER CATCHES (28). Used to retain the quick doff hood on the mask assembly.

• The RIDGE (29) is also used to retain the quick doff hood.

g. UNIVERSAL SECOND SKIN (USMC only) (30). Is made of butyl rubber and covers the facepiece. It providesadditional protection against liquid agents. (Rubber catches and ridges are no longer needed because the universalsecond skin is now larger.)

• Interfaces with hooded overgarments.

• Extends beyond the mask facepiece.

• Interfaces with the QDH.

h. Outserts have RUBBER RINGS (31) that fit over mask assembly eyelens rings to secure outserts to maskassembly. The CLEAR OUTSERTS (32) and NEUTRAL GRAY OUTSERTS (33) prevent scratching of eyelensfrom scratches and reduce fogging of eyelens in cold weather. The neutral gray outserts are used to reduce sunglare.

1-6

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

i. M1 WATERPROOF BAG (34). The folded waterproof bag and a small envelope containing the RUBBER BANDS(35) are packed in carrier. The waterproof bag keeps the mask dry when required by climate and mission.Instructions for use are printed on the waterproof bag.

j. FACEFORM(36)

• Holds mask assembly in proper shape when stored longer than 30 days.

M40A1 PECULIAR

NOTEThe soldier may be issued either mask carrier. Major differencesare size and accessory stowage locations.

k. Mask Carrier is made of mildew-resistant, water-repellant fabric. It has adjustable straps. It is closed with a flap heldby hook and pile material.

• IMPROVED FIELD MASK CARRIER (37) is designed to serve the field mask only. It has a larger velcro closingsurface, the AQD opening has been eliminated, the ID area is now camouflaged, the stiffeners have been removed,it is wider and not as deep, and the interior pockets are larger.

• FIELD MASK CARRIER (38) was designed to serve field and combat vehicle masks.

1-7

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

1-8. LOCATION AND DESCRIPTION OF MAJOR COMPONENTS--(CONT )

M42A2 PECULIAR

I. DETACHABLE MICROPHONE (39). Located in the recess of the front voicemitter.

j. CANISTER CARRIER Improved (40) - Original (41)

NOTEYou may have been issued the original canister carrier or theproduct improved model of the canister carrier. They areinterchangeable.

• The IMPROVED CANISTER CARRIER (40) is larger and interfaces with the a C2/C2A1 filter canisters, as well as, avariety of North Atlantic Treaty Organization (NATO) filter canisters. The cover now screws on rather than attachingwith lug bolts, there is now a slip ring within the cover and the AQD is detachable and rotates.

• The ORIGINAL CANISTER CARRIER (41) interfaces with the C2/C2AI filter canisters only.

• ARMOR QUICK DISCONNECT (42). Attached to the canister cover (43) and permits the filter canister to be coupledto a vehicle's Gas Particulate Filter Unit (GPFU).

1-8

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

c. HOSE ASSEMBLY (44). The hose assembly connects the filter canister and canister carrier to the mask assembly.

• M42A2 - The hose assembly is attached to the mask assembly with the STAR KNOB (45). The hose assembly isremovable and can be relocated on left or right side of the mask assembly.

NOTEThe soldier may be issued either mask carrier. Major differencesare size and accessory stowage locations.

d. Mask Carrier is made of mildew-resistant, water-repellant fabric. It has adjustable straps. It is closed with a flap heldby hook and pile material.

• COMBAT VEHICLE MASK CARRIER (46). This mask carrier has been redesigned. It is now shaped to aid instowing the filter canister and hose, the velcro closing area has been enlarged to prevent dirt from entering themask carrier, the exterior pouch has been removed, the ID area is now camouflaged, the stiffeners have beenremoved and the interior pockets are larger. It was designed to serve the combat vehicle mask only.

• FIELD MASK CARRIER (47) was designed to serve field and combat vehicle masks.

1-9

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

1-9 DIFFERENCE BETWEEN MODELS

This chart shows major equipment and differences between the M40A1 and M42A2.

Table 1-1. Differences Between Models

MASK FEATURESCHEMICAL

BIOLOGICAL MASK

M40A1 M42A2

Facepiece

Filter canister is connected to end coupling of hose assembly

Detachable star knob hose assembly

Filter Canister attached directly to facepiece

Hood (One-Piece)

Quick Doff Hood

Second Skin

Universal Second Skin

Universal Second Skin (USMC only)

Clear/Neutral Outserts

Detachable Microphone (External)

Front and Side Voicemitter

Field Mask Carrier

Improved Field Mask Carrier

Combat Vehicle Mask Carrier

Operation Capabilities:

Combat Vehicle

Transportable and stored in carrier

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

1-10

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

1-10 EQUIPMENT DATA

a. Tabulated Data

Weight (with carrier and accessories):

M40A1 mask. 3.8 lbs. (1.73 kg)

M42A2 mask. 4.5 lbs. (2.05 kg)

Dimensions:

M40A1 mask Mask with carrier...12 x 14 x4.5 in. (30.5 x 35.6 x 11.4 cm.)

M42A2 mask Mask with carrier...12x 14 x4.5 in. (30.5 x 35.6 x 11.4 cm.)

b. Shipping and Storage Data.

Shipping and Storage Data is identical for the M40A1 and M42A2 masks.

Number and type of pack: 10 per fiberboard container, 1 per fiberboard box.

Fiberboard container:

Dimensions: 34.375 x 22 x 16.75 in. (87 x 55.9 x 425 cm)

1-11

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

SECTION III. PRINCIPLES OF OPERATION

1-11 PRINCIPLES OF OPERATION

a. M40A1 PRINCIPLES OF OPERATION

(1). Air enters the FILTER CANISTER (1), which is screwed into the side of the mask. The filter canister filters out CBagents, toxins, and radioactive fallout particles from contaminated air. Air then passes over the AIRFLOWDEFLECTOR (2) which is located inside the facepiece and on the same side as the filter canister. The air thenmoves into the eye area of the facepiece.

(2). From the eye area, air enters the NOSECUP (3) through NOSECUP VALVES (4). Filtered air from the nosecup isinhaled by the soldier. Exhaled air is passed through the nosecup area and out through the OUTLET VALVE (5).The OUTLET VALVE COVER (6) protects the outlet valve from contamination and damage, and provides a retainerfor the external drink tube.

1-12

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

b. M42A2 PRINCIPLES OF OPERATION

(1). Air enters the filter canister, which is held in the CANISTER CARRIER (7). The filter canister filters out CB agents,toxins, and radioactive fallout particles from contaminated air. Air then passes through the HOSE (8) andDEFLECTOR (9) which is located inside the mask assembly and on the same side as the hose assembly. The airthen moves into the eye area of the mask assembly.

(2). From the eye area, air enters the NOSECUP (10) through NOSECUP VALVES (11). Filtered air from the nosecup isinhaled by the soldier. Exhaled air is passed through the nosecup area and out through the OUTLET VALVE (12).The OUTLET VALVE COVER (13) protects the outlet valve from contamination and damage, and provides aretainer for the external drink tube.

1-13 (1-14 blank)

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

CHAPTER 2 UNIT MAINTENANCE INSTRUCTIONS

Table of Contents

Para. Page

SECTION I. REPAIR PARTS, SPECIAL TOOLS, TMDE, AND SUPPORT EQUIPMENT............... 2-3

2-1. COMMON TOOLS AND EQUIPMENT ................................................................................................................... 2-3

2-2. SPECIAL TOOLS, TMDE, AND SUPPORT EQUIPMENT ...................................................................................... 2-3

2-3. REPAIR PARTS..................................................................................................................................................... 2-3

SECTION II. SERVICE UPON RECEIPT.......................................................................................... 2-3

2-4. GENERAL.............................................................................................................................................................. 2-3

2-5. SERVICE UPON RECEIPT OF MATERIAL............................................................................................................ 2-3

2-6. IDENTIFYING AN INDIVIDUAL'S MASK .............................................................................................................. 2-18

SECTION III. EQUIPMENT/USER FITTING INSTRUCTIONS........................................................ 2-19

2-7. ADJUSTING MASK ASSEMBLY AT INITIAL FITTING.......................................................................................... 2-19

2-8. CHECKING MASK ASSEMBLY FOR PROPER FUNCTION................................................................................. 2-23

2-9. CHECKING DRINKING SYSTEM FOR PROPER FUNCTION.............................................................................. 2-28

SECTION IV. TROUBLESHOOTING.............................................................................................. 2-29

2-10. TROUBLESHOOTING PROCEDURES.............................................................................................................. 2-29

SECTION V. PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS) ....................... 2-39

2-11. INTRODUCTION TO PMCS TABLE................................................................................................................... 2-39

2-12. PMCS PROCEDURES....................................................................................................................................... 2-39

SECTION VI. CONVERSION PROCEDURES................................................................................ 2-45

2-13. LEFT/RIGHT FILTER CANISTER/HOSE ASSEMBLY CONVERSION................................................................ 2-45

2-14. M40A1 TO M42A2 CONVERSION ..................................................................................................................... 2-51

2-15. M42A2 TO M40A1 CONVERSION ..................................................................................................................... 2-52

2-1

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

Table of ContentsPara Page

SECTION VII. MAINTENANCE PROCEDURES ............................................................................ 2-53

2-16. GENERAL.......................................................................................................................................................... 2-53

COMMON TASKS

2-17. INTERNAL DRINK TUBE ................................................................................................................................... 2-54

2-18. QUICK DISCONNECT COUPLING, EXTERNAL DRINKTUBE........................................................................... 2-56

2-19. HEAD HARNESS............................................................................................................................................... 2-57

2-20. NOSECUP VALVE DISKS.................................................................................................................................. 2-58

2-21. AIRFLOW DEFLECTOR, INLET VALVE, AND VALVE BODY ............................................................................ 2-59

2-22. OUTLET VALVE COVER AND OUTLET VALVE DISK....................................................................................... 2-63

2-23. SIDE VOICEMITTER, VOICEMITTER RETAINER, AND GASKET ..................................................................... 2-65

2-24. INTERNAL DRINKTUBE NIPPLE....................................................................................................................... 2-66

2-25. OPTICAL INSERT KIT ....................................................................................................................................... 2-68

M40A1 PECULIAR TASKS

2-26. M40A1 FACEPIECE........................................................................................................................................... 2-73


2-27. M42A2 FACEPIECE........................................................................................................................................... 2-74

2-28. CLAMP COVER................................................................................................................................................. 2-75

2-29. PORT GASKET.................................................................................................................................................. 2-76

SECTION VIII. CLEANING AND SANITIZING ............................................................................... 2-77

2-30. CLEANING M40A1............................................................................................................................................. 2-77

2-31. SANITIZING M40A............................................................................................................................................. 2-81

2-32. CLEANING M42A2............................................................................................................................................. 2-85

2-33. SANITIZING M42A2........................................................................................................................................... 2-91

SECTION IX. PREPARATION FOR STORAGE OR SHIPMENT................................................... 2-95

2-34. PREPARATION FOR STORAGE OR SHIPMENT .............................................................................................. 2-95

2-2

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

CHAPTER 2UNIT MAINTENANCE INSTRUCTIONS

SECTION I. REPAIR PARTS, SPECIAL TOOLS, TMDE, AND SUPPORTEQUIPMENT

2-1. COMMON TOOLS AND EQUIPMENT

• For authorized common tools and equipment, refer to the Modified Table of Organization and Equipment(MTOE) applicable to your unit.

2-2. SPECIAL TOOLS, TMDE, AND SUPPORT EQUIPMENT

• Special tools, TMDE, and support equipment required are listed in Appendix C-Repair Parts and Special ToolsList (RPSTL) and Appendix B-Maintenance Allocation Chart (MAC).

2-3. REPAIR PARTS

• Repair parts are listed and illustrated in Appendix C of this manual.

SECTION II. SERVICE UPON RECEIPT

2-4. GENERAL

• This section contains instructions and procedures for services to be performed upon receipt of a new mask.These services include unpacking and checking the mask.

2-5. SERVICE UPON RECEIPT OF MATERIAL

a. Table 2-1 contains instructions for performing the services required upon receipt of the M40A 1 mask.b. Table 2-2 contains instructions for performing the services required upon receipt of the M42A2 mask.

2-3

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-5 SERVICE UPON RECEIPT OF MATERIAL

Table 2-1. Service upon receipt -- M40A1 Mask

LOCATION ITEM ACTION REMARKS

UNPACKING

1. OUTER BOX,FIBERBOARD OFWOOD, ASAPPLICABLE

2. INNERFIBER-BOARDBOX

Flaps (fiberboard box) ortop (wood box)

a. Facepiece/second skinassembly.

WARNINGAfter removing the top of a woodbox, remove nails or bend nails toprevent injury.

NOTEIf possible, retain shipping boxesfor possible future turn-ins.

Open box by cutting tape andbanding on fiberboard boxes orremove top by cutting bandingand prying open top of woodboxes. Remove nails or bendnails over to prevent injury.Remove inner fiberboard boxes.Remove barrier bar aroundfacepiece folder.

NOTESecond skin is packaged on top ofthe facepiece in the facepiece/second skin or universal secondskin assembly.

Open inner box (1). Remove thefacepiece/universal second skinor second skin assembly (2). Takethe facepiece/universal secondskin or second skin assembly outof the sealed bag and discard thebag. Remove universal secondskin (3) or second skin (4).

NOTEMasks stored more than 30 daysshall be stored with faceform infacepiece. Keep all faceforms. DoNot Discard.

Loosen head harness straps offacepiece (5) and removeclamshell (6) and faceform (7).Cut tabs (8) where indicated.Store at organization level.Discard clamshell.

2-4

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2



UNPACKING (CONT)

2.INNER FIBER-BOARD BOX (CONT)

b. Fiberboard separator:hood assembly, filtercanister, outserts.

Remove protective polycovering(9) from eyelenses (10) by pullingcovering away from eyelens tostretch, then forward to remove.Discard protective covering.

Remove fiberboard separator(11).

Take quick doff hood (12) out ofheat-sealed bag and discard bag.

Store unopened canisters (13)until issued. Record lot number ofcanister in accordance with unitSOP.

Take clear (14) and neutral gray(15) outserts out of heat-sealedbags and discard bags.

2-5

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-5 SERVICE UPON RECEIPT OF MATERIAL (CONT)



UNPACKING (CONT

INSPECTION

c. Poly-bag Mask Carrier

d. Waterproof bag

e. Heat sealed bag-manual

Take improved field mask carrier(16) out of bag and discard bag.Take field mask carrier (17) out ofbag and discard bag.

Remove waterproof bag (18) inself-sealing plastic bag. Checkthat three rubber bands (19) areincluded.

Take manual (20) out of heat-sealed bag. Bag may be retainedto protect manual.

Inspect equipment for damageincurred during shipment. Ifequipment has been damaged,report the damage on SF 364,Report of Discrepancy (ROD).Check equipment against packingslip to see if shipment is complete.Report all discrepancies inaccordance with the instructionsof DA PAM 738-750.

2-6

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2



PREPARINGTO STOWTHE MASK CARRIER

a. Universal second skin orsecond skin

b. Clear outserts

c. Mask Assembly

d. Mask Assembly (22)(mask assembly, hood,head harness andfaceform).

e. Mask Assembly (23)(mask assembly, headharness and faceform). (Foruse with hoodedovergarments.) (USMConly)

Install universal second skin (3) orsecond skin (4) on facepiece (seeOperator's Manual).

Install clear Outserts (15) onfacepiece (see Operator'sManual).

Record alphanumeric number (21)in a property book or log IAW unitSOP.

Place faceform (7) into maskassembly. Place neatly foldedquick doff hood ( 12) into back offaceform. Tighten head harness tohold quick doff hood.

Place faceform into maskassembly. Tighten head harnessto hold facefom

2-7

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-5 SERVICE UPON RECEIPT OF MATERIAL (CONT)



STOWING IMPROVEDFIELDMASK CARRIER

a. Waterproof bag

b. Neutral gray outserts

c. Operator's manual

d. Mask Assembly

a. Install waterproof bag (18 )inside left end pocket.'

b. Install neutral gray outserts (14)in left back pocket.

c. Pack operator's manual (20) inthe right back pocket.

d. Store the mask assembly (22).

2-8

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2



STOWINGFIELDMASKCARRIER

a. Waterproof bag


c. Operator's manual

d. Mask Assembly

a Install waterproof bag (18 )inside left back pocket.

b. Install neutral gray outserts (14)in back middle pocket.

c. Pack operator's manual (20) inthe right back pocket.

d. Store the mask assembly (22).

2-9

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-5. SERVICE UPON RECEIPT OF MATERIAL (CONT)



UNPACKING

1. OUTERBOX,FIBERBOARD ORWOOD, ASAPPLICABLE

2. INNER FIBER-BOARD BOX

Flaps (fiberboard box) ortop (wood box)

a. Facepiece fiberboardfolder, outserts, and secondskin or universal secondskin.

WARNINGAfter removing the top of a woodbox, remove nails or bend nails toprevent injury.

NOTEIf possible, retain some shippingboxes for possible future turn-ins.Open box by cutting tape andbanding on fiberboard boxes orremove top by cutting bandingand prying open top of woodboxes. Remove nails or bendnails over to prevent injury.Remove inner fiberboard boxes.Remove barrier bar aroundfacepiece folder.

NOTESecond skin, or universal secondskin is packaged on top of thefacepiece in the facepiece holder.

Take clear (1) and neutral gray (2)outserts out of bags and discardbags.

2-10

TM 3-4240-346-20&PTM 09204A/09205A - 20&P12



UNPACKING (CONT)

2. INNER FIBER-BOARDBOX (CONT)

a. Facepiece fiberboardfolder, outserts, and secondskin, or universal secondskin. (Cont)

b. Facepiece and faceform.

c. Mask Carrier

NOTEMasks stored more than 30 daysshall be stored with faceform inmask assembly. Keep allfaceforms. Do Not Discard.

Remove facepiece folder (3).Remove facepiece (4) anduniversal second skin (5), orsecond skin (6) and discard bothfolder and bag.

Loosen head harness straps offacepiece (7) and removeclamshell (8) and faceform (9).Cut tabs (10) where indicated.Store faceform at organizationlevel. Discard clamshell.

Remove protective poly-covering(11) from eyelenses (12) bypulling covering away fromeyelens to stretch, then forward toremove. Discard protectivecovering.

Take combat vehicle mask carrier(13) out of bag and discard bag.

2-11

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2


Table 2-2. Service upon receipt -- M42A2 Mask (Cont)


UNPACKING (CONT) d. Mask Carrier.

e. Quick doff hood(M42AI/M42A2).

f. Detachable microphone(M42A2).

Take field mask carrier (14) out ofbag and discard bag.

Take quick doff hood (15) out ofbag and discard bag.

Take detachable microphone (16)out of bag and discard bag.

2-12

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2



UNPACKING(CONT)

h. Canister Carrier

i. Vacuum sealed cancontaining filter canister.

j. Hose assembly

k. Waterproof bag

l. Heat sealed bag-manual

Take canister carrier (17) out ofbag and discard bag.

Store unopened can (18) until is-Sued. Record lot number of filtercanister in accordance with unitSOP.

Take hose assembly (19) out ofbag and discard bag.

Remove waterproof bag (20) fromplastic bag and discard plasticbag. Check that three rubberbands (21) are included.

Take manual (22) out of bag. Bagmay be retained to protectmanual.

2-13

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/




INSPECTION

PREPARING TO STOWTHE MASK CARRIER

a. Universal second skin orsecond skin

b. Clear outserts

c. Detachable Micro-phone (M42A2).

Inspect equipment for damageincurred during shipment. Ifequipment has been damaged,report the damage on SF 364,Report of Discrepancy (ROD).Check equipment against packingslip to see if shipment is complete.Report all discrepancies inaccordance with the instructionsof DA PAM 738-750.

Install universal second skin (5)(see Operator's Manual) orsecond skin (6) (see Operator'sManual) on facepiece.

Install clear Outserts (1) onfacepiece (see Operator'sManual).

Attach detachable microphone(16) to front voicemitter opening offacepiece (see Operator'sManual).

2-14

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2



PREPARING TO STOWTHE MASK CARRIER(CONT)

d. Mask assembly

e. Hose Assembly

f. Mask assembly (24)(mask assembly, hood,head harness and face-form).

g. Mask assembly (25)(mask assembly, hood,head harness and face-form). (For use with hoodedovergarments.)(USMC only)

Record 13 digit alphanumericnumber (23) in a property book orlog IAW unit SOP.

Attach the hose assembly (19) tothe mask assembly (4) (seeOperator's Manual).

Place faceform (9) into maskassembly. Place neatly foldedquick doffhood (15) (M42A1/M42A2) into back of faceform.Tighten head harness to holdquick doff hood.

Place faceform into maskassembly. Tighten head harnessto hold faceform.

2-15

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2




STOWING THECOMBAT VEHICLEMASK CARRIER

a. Waterproof bag


c. Manual

d. Canister Carrier

e. Mask Assembly

Store waterproof bag (20) in rightpocket.

Store neutral gray outserts (2) inleft pocket.

Store operator's manual (22) inthe middle pocket.

Store the canister carrier (17).

Store the mask assembly (24).

2-16

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

Table 2-2. Service upon receipt -- M42A2 MaskLOCATION ITEM ACTION REMARKS

STOWING THE FIELDMASK CARRIER

a. Waterproof bag


c. Manual

d. Canister Carrier

e. Mask Assembly

Store waterproof bag (20) ininside left end pocket.

Store neutral gray outserts (2) inleft back pocket.

Store operator's manual (22) inthe right back pocket.

Store the canister carrier (17).

Store the mask assembly (24).

2-17

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-6. IDENTIFYING AN INDIVIDUAL' S MASK

Although a mask will be used only by the soldier to whom it is issued and fitted, do not make permanent identificationmarking on either mask or mask carrier (AR 700-84). A card may be placed in the exterior side pocket with the soldier'sname or a code number for identification purposes. The date the mask was tested and fitted to the soldier along with the IDcode will be recorded in accordance with local SOP. Include the lot number of the canister and the mask assembly.

Each unit will devise its own code to ensure operational security. Take care not to include any designations that may identifythe parent organization.

2-18

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

SECTION III. EQUIPMENT/USER FITTING INSTRUCTIONS

2-7. ADJUSTING MASK ASSEMBLY AT INITIAL FITTING

THIS TASK COVERS: a. Putting on mask assembly b. Adjusting mask assembly c. Checking mask assembly for fit

INITIAL SETUP:

Personnel Required:NBC NCO or other trained personSoldier to be fitted

Applicable Configurations:M40A1/M42A2

Materials/Parts:M41 Protection Assessment Test System (If Available)ORn-Amyl acetate (banana oil) (item 11, app D)ORStannic Chloride (tube smoke) (item 16, app D)

References:TC 3-41

WARNINGBefore putting on and adjusting mask assembly, soldiers shallremove all hairpins, combs, hair knots, buns, or braids that willinterfere with mask assembly seal. Soldiers must be cleanshaven to prevent mask assembly leaks.

DO NOT wear contact lenses (soft or hard) while wearing CBProtective Masks. Inadequate oxygen supply to the cornealsurface, exposure to dust, dirt, and smoke/ gas may causeserious vision loss or eye damage. Soldiers requiring visioncorrection are provided optical inserts for their protective masks.

NOTEInitial mask assembly fitting should be performed by the unit NBC NCO or other trained person.There is no special tool for sizing with the M40A1/M42A2 masks. You will have to use yourjudgement and the guidelines found in this paragraph on size selection. Initial fitting is donewithout the hood installed.

The protective mask fit may be checked by the following equipment/tests. The order of preferencefor mask fitting and testing is the M41 Protection Assessment Test System (PATS) if available, n-Amyl acetate (banana oil), or stannic chloride (tube smoke).

Detailed instructions for checking the fit with the M41 PATS is found in the M41 operator'smanual and in TC 3-41. Detailed instructions for checking the fit with banana oil is in para 2-8 ofthis manual.

After initial fitting of soldier's mask, determine if soldier fires from right or left. Convert maskaccordingly (para 2-13). Determine if soldier requires vision correction and install as required(para 2-25).

2-19

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-7. ADJUSTING MASK ASSEMBLY AT INITIAL FITTING (CONT)

a. PUTTING ON MASK ASSEMBLY

WARNINGEdges of open can are sharp.

1. Use attached key (1) to open canister can (2) and remove filter canister (3).

NOTEOptical inserts should be installed, if required.

2. Install filter canister on mask assembly (4) (M40A1 only).

3. Feed hose end connector (5) through canister carrier (6) (M42A2 only).

4. Install filter canister on hose connector and secure canister carrier cover (7) (M42A2 only).

5. Loosen head harness (8) so that strap ends are approximately 1 in. (2.5 cm) from buckles.

6. Pull head harness over front of mask assembly (9).

7. Hold hair back from sealing area and place chin in the chin pocket (10).

8. Have soldier slip head harness over head while holding mask assembly against face.

2-20

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

b. ADJUSTING MASK ASSEMBLY

1. Have soldier hold mask assembly (9) tightly against chin.

2 (NBC NCO) Center head harness pad (11) on back of soldier's head and have soldier hold in place.

3. (NBC NCO) Place finger or thumb under buckle (12) of forehead strap (13). Then give strap end short, sharp tugsuntil buckle feels snug. Adjust other forehead strap in same manner.

4. (NBC NCO) Place finger or thumb under buckle (14) of cheek strap (15) and adjust cheek strap until it feels snug.Adjust other cheek strap in same way.

5. Have soldier release mask assembly. Mask assembly should not slip down. If mask assembly slips, readjustforehead straps and cheek straps until mask assembly remains in place.

6. (NBC NCO) Place finger or thumb under buckle (16) of temple strap (17) and adjust temple strap until buckle feelssnug against finger. Repeat adjustment on other temple strap.

CAUTIONImproperly adjusted internal drink tube may irritate lips if ittouches them while wearing mask assembly.

7. Ask if internal drink tube touches soldier's lips. Adjust length of internal drink tube if necessary (para 2-17).

2-21

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-7. ADJUSTING MASK ASSEMBLY AT INITIAL FITTING (CONT)

c. CHECKING MASK ASSEMBLY FOR FIT

WARNINGSoldier's safety depends on proper fitting mask assembly.

NOTEWhen doffing mask, only loosen the cheek straps.

1. Edge of mask assembly (9) comes up on forehead but not into hairline and within 1 in. (2.5 cm) of ear.

2 Temple straps (17) and cheek straps (15) do not cut into ears.

3. Soldier's pupils are within the center one-third area (vertical) (18) of the eyelens (19). Adjust optical inserts ifrequired (para 2-25).

4. Mask assembly does not press flesh so tightly that eyes are partly closed.

5. Bottom of mask assembly does not cut into throat.

6. Skin in front of ear is not wrinkled.

7. Nosecup (20) does not obscure vision.

8 If mask assembly still does not meet above standards, try another size mask.

NOTEFOLLOW-ON MAINTENANCE: Check the mask assembly for Proper Function. (para 2-8).

2-22

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-8. CHECKING MASK ASSEMBLY FOR PROPER FUNCTION

THIS TASK COVERS: a. Testing mask assembly with M41 PATSb. Testing mask assembly with n-Amyl acetate

INITIAL SETUP:


Personnel Required:NBC NCO or other trained personSoldier to be tested

Materials/Parts:M41 PATSApplicator (item 1, app D)n-Amyl acetate (banana oil) (item 11, app D)Rubber gloves (item 8, app D)

References:

TM 3-4240-346- 10/TM09204A/09205A-10/1.TC 3-41Commercial Manual (M41)

NOTEPMCS should be conducted and verified prior to proper function testing.

The order of preference for mask fitting and testing is the M41 Protection Assessment Testsystem (PATS) if available, n-Amyl acetate (banana oil), or stannic chloride (tube smoke).

COMMON

a. TESTING MASK ASSEMBLY WITH M41 PATS

1. Have soldier put on and adjust mask assembly (para 2-7).

2. Refer to TC 3-41 and Commercial Manual for instructions on the use of the M41 PATS.

2-23

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-8. CHECKING MASK ASSEMBLY FOR PROPER FUNCTION (CONT)

COMMON (CONT)

b. TESTING MASK ASSEMBLY WITH N-AMYL ACETATE

WARNINGN-amyl acetate is flammable. DO NOT touch skin (or the soldier)with n-Amyl acetate. It could irritate the skin. Wear rubbergloves. DO NOT smoke around n-Amyl acetate. Keep n-Amylacetate away from an open flame. DO test mask assembly in awell-ventilated room. N-Amyl acetate may be toxic if inhaled inquantity.

NOTESoldier should breathe deeply through nose only. If soldier smells n-Amyl acetate just beforemasking, test results will be inaccurate.

1. Dip applicator in n-Amyl acetate (banana oil).

2. Move applicator approximately 1 to 2 in. (2.5 or 5.1 cm) from mask assembly as follows:

a. Have soldier turn head to left and move applicator completely around outer edge of mask assembly.

b. Have soldier turn head to the right, again move applicator around outer edge of mask assembly.

2-24

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

c. Have soldier tilt head upward and turn head from side to side, move applicator under chin around outer edge ofmask assembly.

d. Have soldier tilt head forward, move applicator around outer edge of mask assembly.

2-25

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-8. CHECKING MASK ASSEMBLY FOR PROPER FUNCTION (CONT)b. TESTING MASK ASSEMBLY WITH N-AMYL ACETATE (CONT)

M40A1 PECULIAR

e. Have soldier smile and frown while looking straight ahead. Move applicator around both eyelenses (1), frontvoicemitter (2), side voicemitter (3), filter canister (4) and outlet valve cover (5).

f. Instruct soldier to press palms firmly over filter canister, but not so firmly that mask assembly is distorted andloses its seal. Have soldier breathe in, creating a vacuum and collapsing mask assembly. Move applicatoraround outer edge of mask assembly before having soldier breathe out.

M42A2 PECULIAR

g. Have soldier smile and frown while looking straight ahead. Move applicator around both eyelenses (1), frontvoicemitter (2), side voicemitter (3), star knob (6), and outlet valve cover (5).

h. To test seal integrity for the connector at each end of the hose assembly, check the clamp cover (7) on eachend of the hose (8).

i. Move applicator around the canister carrier (9).

j. Instruct soldier to press palm firmly over Armor Quick Disconnect Opening (10). Have soldier breathe in,creating a vacuum and collapsing mask assembly. Move applicator around outer edge of mask assembly beforehaving soldier breathe out.

2-26

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

NOTEIf soldier being tested smells n-Amyl acetate (banana oil) during initial fitting and testing,a 5-7 minute odor sensitivity recovery period is required before retesting.

4. If soldier can smell n-Amyl acetate, readjust head harness to improve fit (para 2-7) and repeat above check.

5. If soldier cannot smell n-Amyl acetate, have him unmask and smell the applicator to be sure that his sense of smellis not impaired. If soldier's sense of smell is impaired, the mask assembly must be tested in a CS (irritant) chamberor using a smoke tube (item 16, app D) and an aspirator bulb (item 4, app D) containing stannic chloride, whichproduces an irritating acid smoke. The smoke tube test should be conducted in still air in an area that can beventilated.

NOTEFOLLOW-ON MAINTENANCE: Remove mask assembly and stow in carrier in accordancewith TM 3-4240-346-10/TM 09204A/09205A-10.

2-27

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-9. CHECKING DRINKING SYSTEM FOR PROPER FUNCTION

THIS TASK COVERS: Testing Drinking System

INITIAL SETUP:


Personnel Required:NBC NCO or other trained personSoldier (mask wearer)

TESTING DRINKING SYSTEM

a. Steady mask assembly (1), withdraw quick disconnect coupling half (2) from retainer (3) and let it hang freely.

b. Grasp internal drink tube (4) between your lips.

WARNINGIf resistance is not felt when checking drinking system, the drinking system leaks.

c. Blow into internal drink tube. If resistance is not felt, drink system is leaking.

d. A more positive test may be done on the external drink tube quick disconnect by the following procedure:(1) Fill cup (5) full of water.(2) Place mask assembly on face.(3) Dip quick disconnect in cup filled with water.(4) Blow into internal drink tube.(5) Watch for bubbles in water. If no bubbles, quick disconnect is operational. If bubbles are detected, the

quick disconnect is not operational. (Refer to para 2-18).

2-28

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

SECTION IV. TROUBLESHOOTING

2-10. TROUBLESHOOTING PROCEDURESa. Perform functional test first. Then use the symptom index for quick access to the troubleshooting procedures.b. The following describes the use of the troubleshooting procedures.

SYMPTOM INDEX PAGE

COMMON

1. Eyelens Fog Excessively..................................................................................................................... 2-30

M140A1 PECULIAR

2. Insufficient Air to User ......................................................................................................................... 2-31

3. Mask Assembly Fails To Seal.............................................................................................................. 2-32

M42A2 PECULIAR

4. Insufficient Air to User ......................................................................................................................... 2-35

5. Mask Assembly Fails To Seal.............................................................................................................. 2-36

2-29

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-10. TROUBLESHOOTING PROCEDURES - (CONT)

COMMON

2-30

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

M40A1 PECULIAR

2-31

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2


M40A1 PECULIAR (CONT)

2-32

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-33

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/



2-34

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

M42A2 PECULIAR

2-35

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2



2-36

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-37

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2



2-38

TM 34240-346-20&PTM 09204A/09205A - 20&P/2

SECTION V. PREVENTIVE MAINTENANCE CHECKS AND SERVICES(PMCS)

2-11. INTRODUCTION TO PMCS TABLEa. General. Unit PMCS is performed semiannually (every 6 months). The soldier may perform semiannual PMCS

under supervision of NBC NCO or other trained person. Unit PMCS is performed to assure that the moreexperienced NBC NCO regularly checks that the soldier is properly doing daily PMCS. This allows the NBCNCO to perform his responsibilities to assure that: 1. The soldiers are properly performing their daily PMCS; 2.The soldiers are properly performing their monthly PMCS; and 3. That the soldiers are involved in performingthe semiannual PMCS. In addition the NBC NCO is responsible for assuring that those checks identified areperformed on a weekly basis during combat situations. Semiannual PMCS and initial and mandatory fitvalidation M41 test will be scheduled and will be recorded on DD Form 314, Preventive Maintenance Scheduleand Record. The Semiannual PMCS will be completely performed in accordance with the applicable operator'smanual (TM 3-4240-346-10/TM 09204A/09205A-10) and this TM. Marine Corps Users will perform and recordsemiannual maintenance in accordance with procedures prescribed in TM 4700-15/1_ and unit SOP.

b. Inspections. The most detailed inspections and PMCS of the mask is performed when it is first received, aftereach use, semiannually and during the annual fit test. The NBC NCO is involved in all of these inspections. Thisallows the NBC NCO to assure that the operator is properly doing the daily PMCS.

c. WARNINGS and CAUTIONS. It is vital to the safety of the operator and the Unit Maintenance personnel that allWARNINGS and CAUTIONS are followed. It is also the responsibility of the NBC NCO to make sure theoperator understands their importance and follows them very carefully.

d. Training Materials. Training materials are available (see Appendix A).

NOTEConduct an initial and annual fit test of all assigned masks using the ProtectionAssessment Test System (PATS M41), if available, banana oil, or stannic chloride.

2-12. PMCS PROCEDURES

The following paragraphs describe the information presented in each column of the PMCS table.a. Item Number Column. Numbers in this column are for reference. When completing DA Form 2404 (Equipment

Inspection and Maintenance Worksheet), include the item number for the check/service indication at fault. Itemnumbers also appear in the order that you must do checks and services for the intervals listed. Record anyfaults that you discover before, during, or after operation. You DO NOT need to record faults that you fix.

b. Interval. This column of your PMCS table tells you when to do a certain check or service.c. Item to be Inspected Column. This column identifies the item to be checked or serviced.d. Procedure Column. This column briefly describes this procedure for performing the check or service. Whenever

replacement or repair is recommended, reference is made to para number for the applicable maintenanceInstruction.

e. Not Fully Mission Capable If: Column. Information in this column only tells you what deficiencies will keep yourequipment from being capable of performing its primary mission safely. DO NOT use your mask if a check andservice shows a fault listed in this column. Shortcomings or minor discrepancies which DO NOT limit operationalcapability or safety of use may require corrective surveillance, but does not "deadline" the mask.

f. Other Table Entries. Be sure to observe all special information and notes that appear in your table.

NOTEAll PMCS tasks are common to both the M40A1 and the M42A2. Therefore, all PMCStasks must be performed regardless of which mask you have. Please note that all tasksare illustrated with the M42A2 mask, however, the procedures indicated are common.

2-39

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-12. PMCS PROCEDURES (CONT)Table 2-3. UNIT PREVENTIVE MAINTENANCE CHECKS AND SERVICES

ITEMNO.

INTERVAL ITEM TO BECHECKED OR

SERVICED

PROCEDURE NOT FULLYMISSION

CAPABLE IF:

1 SemiannualSchedule(PMCS)*

Mask Assembly

CAUTIONDO NOT use a high pressure hose toclean mask. It may damagecomponents.

NOTESanitizing will be done prior to reissueto another soldier or prior to turn-in asexcess.

Make sure finish covers all metalsurfaces. Coat all bare metal surfaceswith lacquer (item 10, APP D).

a. Check mask assembly (1) for dirt orpermanent set which may affect fit orconformance to the face. Signs ofpermanent set are:1. Mask assembly is difficult tospread open.2. Unusual stiffness in sealing areaof mask assembly.

b. Check rubber next to eyelens (2) tobe sure neither eyelens will pull awayfrom mask assembly.

Mask Assembly Maskassembly is dirty enoughto affect mask assemblyseal or function.Mask assembly has apermanent set, orstiffness.

Eyelens will pull awayfrom mask assembly.

COMMON

2-40

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2


Table 2-3. UNIT PREVENTIVE MAINTENANCE CHECKS AND SERVICES

ITEMNO.


SERVICED


CAPABLE IF:

c. Pull head harness (3) over front of mask.Pull chin flap (4) forward so you cansee under it. Look around the twoholes (5) in the chin cup (6) for cutsor tears.

d. Hold nosecup chin flap (4) back soyou can see the internal drink tubeconnection (7).

e. Check the internal drink tubeconnection, inside the maskassembly to see if it is broken. If theconnection looks like the leftillustration, replace the facepiece(para 2-26, M40A1; para 2-27,M42A2). If the connection looks likethe right illustration, replace theinternal drink tube nipple(para 2-25).

The black silicon has anycuts or tears.

Internal drink tube nippleis broken and cannot bereplaced.

2-41

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-12. PMCS PROCEDURES (CONT)

Table 2-3. UNIT PREVENTIVE MAINTENANCE CHECKS AND SERVICES (CONT)

ITEMNO.


SERVICED


CAPABLE IF:

1 SemiannualSchedule(PMCS)*

Mask Assembly (Cont)

f. Place thumb on sideport (8) andfingers inside mask (1). Push upgently with thumb while pullinggently with fingers until mask snapsup to reveal inside of mask area (9)around sideport.

g. Fold back nosecup (10) so view ofarea around sideport is clear.Inspect area around sideport forholes, cuts or tears. Forreplacement see para 2-26, M40A1or para 2-27, M42A2.

Mask has any holes, cutsor tears.

2-42

COMMON

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2


Table 2-3. UNIT PREVENTIVE MAINTENANCE CHECKS AND SERVICES

ITEMNO.


SERVICED


CAPABLE IF:

WARNINGDo nut push up hard on side voicemitterretainer. The retainer could cut thefacepiece and cause leaks.

h. Place thumb on side voicemitter(11) and fingers inside mask (1).Push up gently with thumb whilepulling gently with fingers until masksnaps up to reveal inside of maskarea (12) around side voicemitter.

i. Fold back nosecup ( 10) so view ofarea around side voicemitter isclear. Inspect area around sideportfor holes, cuts or tears. Forreplacement see para 2-26, M40A1or para 2-27, M42A2.

Mask has any holes, cutsor tears.

2-43

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-12. PMCS PROCEDURES (CONT)Table 2-3. UNIT PREVENTIVE MAINTENANCE CHECKS AND SERVICES (CONT)

ITEMNO.


SERVICED


CAPABLE IF:

2

3

SemiannualSchedule(PMCS)*

Front voicemitter

Side voicemitter

a. Check Front Voicemitter (13 ) fordamage, cracks or distortion thatmay affect voice transmission.

a. Remove side voicemitter retainer(14) by unscrewing counterclockwise with the D-ring (15) onthe carrier. Inspect retainer forcracks or distortion. Forreplacement see para 2-23.

b. Remove side voicemitter (16) andinspect for holes, cracks, orwarping. For replacement seepara 2-23.

c. Remove gasket (17) and check forsplits, sticky, or compressed areas.For replacement see para 2-23.

Front Voicemitter iscracked, damaged ordistorted.

Side voicemitter retainerhas cracks or distortion.

Side voicemitter retainerhas cracks or distortion.

Gasket is split, sticky orcompressed.

2-44

COMMON

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

SECTION VI. CONVERSION PROCEDURES

2-13. LEFT/RIGHT FILTER CANISTER/HOSE ASSEMBLY CONVERSION

THIS TASK COVERS: Conversion Instructions

INITAL SETUP:

Applicable Configurations:

M40A1/M42A2

Equipment condition:

Quick Doff Hood removed. (See Operator's Manual)

CONVERSION INSTRUCTIONS

1. Remove filter canister (I) by turning counterclockwise (M40A1 only).

2. Remove hose (2) by turning the star knob (3) counterclockwise (M42A2 only).

CAUTIONBe careful when disconnecting buttons. The mask assembly maybe damaged if care is not exercised.

3. Disconnect the airflow deflector (4) from mask assembly (5) by carefully pulling the silicon rubber housing (6) awayfrom the airflow deflector buttons (7).

2-45

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-13. LEFT/RIGHT HOSE ASSEMBLY CONVERSION (CONT)

4. Grasp a tab (8) on inlet valve body (9) and pull toward center of inlet valve body until unsealed from sideport (10).

5. Tuck unseated portion of inlet valve body into the mask assembly. Remove airflow deflector from mask assembly.

6. Remove side voicemitter retainer (11) by unscrewing counterclockwise using the D-ring (12) on the mask carrier.

2-46

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

7. Remove side voicemitter (13) from mask assembly by pressing from inside of mask assembly (5). Remove gasket(14) from sideport (10) housing on mask exterior.

WARNINGBe sure the inlet valve body is installed on the post of the airflowdeflector with the tabs of the inlet valve body away from the inletvalve disk. If it is installed improperly, the mask will leak.

8. Check that inlet valve body (9) is installed on the post of the airflow deflector with the tabs (8) of the inlet valve bodyaway from the airflow deflector (4).

9. Position airflow deflector in pocket on opposite side of mask assembly.

2-47

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-13. LEFT/RIGHT HOSE ASSEMBLY CONVERSION (CONT)

CAUTIONDO NOT pull on spokes of valve body while installing. This will break the spokesand require replacement of the valve body.

10. With one hand push inlet valve body (9) through sideport (10). With other hand pull on thick outer rim (15) of valvebody until valve body is completely through sideport.

11. Push buttons (7) on sides of airflow deflector (4) into button holes (16) in mask assembly pocket.

12. Press lightly around thick outer rim of valve body until the valve body seats in the sideport.

2-48

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

13. Install filter canister (1) by turning clockwise.

14. Install hose (2) by turning star knob (3) clockwise.

WARNINGBe sure the side voicemitter is installed with the flange and fourbeads facing out. If installed incorrectly it could cause the maskassembly to leak.

15. Position gasket (14) in sideport (10).

16. Install side voicemitter (13) with four beads (17) facing out..

17. Position side voicemitter retainer (I 1) in sideport.

2-49

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-13. LEFF/RIGHT HOSE ASSEMBLY CONVERSION (CONT)

18. Tighten voicemitter retainer (11) by turning clockwise with the D-ring (12) on the mask carrier strap.

19. Check for proper function (para 2-8).

2-50

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-14. M40A1 TO M42A2 CONVERSION


INITIAL SETUP:


M40A1



Materials/Parts:

Detachable MicrophoneHose AssemblyCanister CarrierCombat Vehicle Mask Carrier


1. Remove filter canister (1) (see Operator's Manual).

2. Install hose assembly (2) (see Operator's Manual).

3. Install filter canister in canister carrier (3) (see Operator's Manual).

4. Install detachable microphone (4) (see Operator's Manual).

5. Stow mask in combat vehicle mask carrier and turn in field mask carrier.

2-51

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-15. M42A2 TO M40A1 CONVERSION


INTIALSETUP:


M42A2



Materials/Parts:

Field Mask Carrier


1. Remove hose assembly (1) (see Operator's Manual).

2. Remove filter canister (2) from canister carrier (3) (see Operator's Manual).

3. Remove detachable microphone (4) (see Operator's Manual).

4. Install filter canister by turning clockwise (see Operator's Manual).

5. Stow mask in field mask carrier and turn in combat vehicle mask carrier, detachable microphone, and canistercarrier.

2-52

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

SECTION VII. MAINTENANCE PROCEDURES

2-16. GENERAL

a. The maintenance procedures in this section are to be performed by a unit NBC NCO or by the user under unitNBC NCO supervision.

b. This section is divided into those tasks which are common to the M40A1 and the M42A2, those tasks whichare peculiar to the M40A 1, and those tasks which are peculiar to the M42A2. Common tasks are illustratedwith the M42A2.

c. This section contains detailed instructions for replacing the following components.

Para. Page

COMMON TASKS

2-17. INTERNAL DRINKTUBE .......................................................................................................................................2-54

2-18. QUICK DISCONNECT COUPLING, EXTERNAL DRINK TUBE.............................................................................2-56

2-19. HEAD HARNESS..................................................................................................................................................2-57

2-20. NOSECUP VALVE DISKS.....................................................................................................................................2-58

2-21. AIRFLOW DEFLECOR, INLET VALVE, AND VALVE BODY..................................................................................2-59

2-22. OUTLET VALVE COVERAND OUTLET VALVE DISK...........................................................................................2-63

2-23. SIDE VOICEMITTER, VOICEMlTTER RETAINER, AND GASKET ........................................................................2-65

2-24. INTERNAL DRINK TUBE NIPPLE........................................................................................................................2-66

2-25. OPTICAL INSERT KIT ..........................................................................................................................................2-68


2-26. M40A1 FACEPIECE..............................................................................................................................................2-73


2-27. M42A2 FACEPIECE..............................................................................................................................................2-74

2-28. CLAMP COVER....................................................................................................................................................2-75

2-29. PORT GASKET.....................................................................................................................................................2-76

2-53

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

COMMON

2-17. INTERNAL DRINK TUBE

THIS TASK COVERS: a. Removal b. Installation c. Checking for Fit

INITIAL SETUP:


Materials/Parts:Shears (item 14, app D)

a.REMOVALCAUTION

Do not scratch plastic eyelens while performing maintenance procedures.

NOTEThere are two types of internal drink tubes. The original drinktube and a revised drink tube which is used only when the drinktube nipple has been replaced. Both are illustrated.

1. Lay mask assembly (1) face down on nonabrasive surface.

2. Grasp internal drink tube (2) at drink tube coupling (3) and pull internal drink tube away from coupling.

b.INSTALLATION

1. Lay mask assembly face down on nonabrasive surface.

2. Install internal drink tube on drink tube coupling and press internal drink tube until it bottoms fully against drink tubecoupling.

2-54

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

c.CHECKING FOR FITCAUTION

Internal drink tube will irritate lips if it touches them while wearing maskassembly.Internal drink tube must be removed from mask assembly prior to adjustinglength to prevent damage to mask assembly.

NOTESlight pressure on the top of the outlet valve body shouldenable the internal drink tube to be grasped by the soldier'slips.

1. Have soldier put on mask assembly and check to see if internal drink tube touches lips.

2. If internal drink tube (2) touches soldier's lips while wearing mask assembly (1), adjust length of internal drink tubeas follows:

a. Remove internal drink tube from mask assembly.

b. Cut internal drink tube behind first barb (4).

c. Install internal drink tube.

CAUTIONDO NOT remove the last barb, as this is needed for proper function.

3. Repeat steps 1 and 2, if necessary, to achieve proper fit.

2-55

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

COMMON (CONT)

2-18. QUICK DISCONNECT COUPLING, EXTERNAL DRINK TUBE

THIS TASK COVERS: a. Removal b. Installation

INITIAL SETUP:


a. REMOVAL

1. Lay mask assembly (1) face up.

2. Remove quick disconnect coupling (2) from retainer (3).

3. Grasp external drink tube (4) where it joins the quick disconnect coupling , with one hand, and with the other, graspthe quick disconnect coupling and pull away with a twisting motion, disengaging the external drink tube from thequick disconnect coupling.

b.INSTALLATIONNOTE

Quick disconnect tube connection may be moistened with waterto aid in coupling it with the rubber tubing.

1. Lay mask assembly face up.

2. Insert quick disconnect coupling into the external drink tube and, with a twisting motion, press drink tube in place.Ensure tube extends over the nipple end of the quick disconnect by 5/8 - 3/4 inch.

3. Verify drink system for leaks in accordance with para 2-9.

4. Reinstall quick disconnect coupling in retainer.

5. Check for leaks in accordance with para 2-9.

2-56

TM 3-4240-346-20&PTM 09204A/09205A 20&P/2

2-19. HEAD HARNESS


INITIAL SETUP:


a. REMOVAL

CAUTIONDo not scratch plastic eyelens while performing maintenance procedures.

• Work head harness straps (1) out of buckles (2).

b. INSTALLATION

NOTEElastic webbing that joins the two forehead straps must be onoutside to avoid hot spots on head.

1. Position head harness (3) in mask assembly (4) with head harness straps next to buckles and tab (5) down.

2. Work head harness straps into buckles and pull through approximately 1 in. (2.5 cm) so that head harness strapends are outside.

3. Stretch head harness away from mask assembly and check that buckles hold head harness straps tightly.

4. Perform Initial Fitting Procedures. (para 2-7)

2-57

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/

COMMON (CONT)

2-20. NOSECUP VALVE DISKS


INITIAL SETUP:


a. REMOVAL


To avoid tears, do not stretch rubber more than necessary to remove or installparts.

1. Pull head harness (1) over front of mask assembly (2).

2. Curl back lip of nosecup (3) to expose nosecup valve seat (4) and valve disk (5).

3. Pull nosecup valve disk out of each nosecup valve seat from inside of nosecup.

b. INSTALLATIONNOTE

It may be necessary to pull on nosecup valve disk stem fromoutside of nosecup while pressing it into the nosecup valve seatfrom inside of nosecup.

Moisten the stem of nosecup valve disks with water to aid ininstallation.

1. Press nosecup valve disk into nosecup valve seat from inside of nosecup until nosecup valve disk is flat againstnosecup valve seat and the stem (6) slips completely through the hole (7) in the nosecup valve body.

2. Gently rotate nosecup valve disk to make sure it is completely seated.

3. Repeat steps 1. and 2. to install remaining nosecup valve disk.

4. Return head harness to its original position.

2-58

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-21. AIRFLOW DEFLECTOR, INLET VALVE, AND VALVE BODY


INITIAL SETUP:


Equipment Condition:Hose removed (M40A1/M42A2)Canister carrier removed (M40A1/M42A2)Quick Doff Hood Removed (M40A1/M42A2)

a. REMOVAL


Be careful when disconnecting buttons. The mask assembly may be damaged ifcare is not exercised.

1. Disconnect the airflow deflector (1) from mask assembly (2) by carefully pulling the silicon rubber housing awayfrom the airflow deflector buttons (3).

2. Grasp a tab (4) on inlet valve body (5) and pull toward center of inlet valve body until unseated from sideport (6).

2-59

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

COMMON (CONT)

2-21. AIRFLOW DEFLECTOR, INLET VALVE, AND INLET VALVE BODY (Cont)

a. REMOVAL (Cont)

3. Tuck unseated portion of inlet valve body (5) into the mask assembly. Remove airflow deflector (1) from maskassembly (2).

4. Grasp inlet valve body with thumb under two spokes (7). Pull and peel off airflow deflector post (8).

5. Pull inlet valve disk (9) from airflow deflector post.

2-60

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

b. INSTALLATION

WARNINGBe sure the inlet valve body is installed on the post of the airflowdeflector with the tabs of the inlet valve body away from the inletvalve disk. If it is install improperly, the mask will leak.

NOTEThere are two sizes of deflectors. Ensure that the deflector sizematches the mask size.

1. Position inlet valve disk (9) on lower groove (10) of airflow deflector post (8).2. Position the inlet valve body (5) on the airflow deflector post. Be sure that the tabs (4) of the inlet valve body face

away from the inlet valve disk.3. Position airflow deflector (1) in pocket on side of mask assembly.

CAUTIONDO NOT pull on spokes of inlet valve body while installing. This will break thespokes and require replacement of the inlet valve body.

4. With one hand push inlet valve body through sideport (6). With other hand pull on thick outer rim (11) of inlet valvebody until inlet valve body is completely through sideport.

2-61

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

COMMON (CONT)

2-21. AIRFLOW DEFLECTOR, INLET VALVE, AND INLET VALVE BODY (Cont)

b. INSTALLATION (Cont)

5. Push buttons (3) on sides of airflow deflector (1) into button holes (12) in mask assembly pocket.

6. Press lightly around thick outer rim (11) of inlet valve body (5) until the inlet valve body seats in the sideporthousing.

7. Check for Proper Function (para 2-8).

2-62

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-22. OUTLET VALVE COVER AND OUTLET VALVE DISK


INITIAL SETUP:


a. REMOVAL


Do not damage cover when removing outlet valve cover.

1. Pull quick disconnect coupling (1) out of retainer (2) on outlet valve cover (3).

2. Pull up on drink tube retainer (4) on bottom of outlet valve cover until outlet valve cover is disengaged from outletvalve body (5).

3. Remove outlet valve cover from flanges (6) on top of outlet valve body.

4. Pull outlet valve disk (7) out of outlet valve body and discard.

2-63

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

COMMON (CONT)

2-22. OUTLET VALVE COVER AND OUTLET VALVE DISK (CONT)

b. INSTALLATION

CAUTIONDo not use any tools or instruments to install outlet valve disk. Damage to valve seat mayoccur which would cause leakage.

NOTEMoisten stem of outlet valve disk with water to aid installingoutlet valve disk into outlet valve body.

1. Start stem (8) of outlet valve disk (7) through hole (9) in middle of outlet valve body (5).

2. Press outlet valve disk in while pulling on the inside stem of the outlet valve disk until shoulder of stem slips throughhole in outlet valve body.

3. Check that outlet valve disk lies flat and smooth and has continuous contact with outlet valve seat

4. Rotate outlet valve disk with finger to make sure it is properly seated.

5. Install outlet valve cover (3) on flanges (6) on top of outlet valve body.

6. Using drink tube retainer (4) on bottom of outlet valve cover, pull outlet valve cover over face of outlet valve body.Made sure outlet valve cover snaps in place around outlet valve body.

7. Install quick disconnect coupling (1) securely in retainer (2). Fasten external drink tube (10) to drink tube retainer.

8. Check for Proper Function (para 2-8).

2-64

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-23. SIDE VOICEMITTER, VOICEMITTER RETAINER, AND GASKET


INITIAL SETUP:


a. REMOVAL


1. Remove side voicemitter retainer (1) by unscrewing counterclockwise using the D-ring (2) on the mask carrier strap.

2. Remove the side voicemitter (3) and gasket (4) by pushing from inside of mask out of the side port (5).

b. INSTALLATIONWARNING

Be sure the side voicemitter is installed with the flange and fourbeads facing out. If installed incorrectly it could cause the maskassembly to leak.

1. Position gasket in sideport of mask assembly (6).

2. Install side voicemitter in sideport, with four beads (7) facing out.

3. Position side voicemitter retainer in sideport; tighten with D-ring on mask carrier strap by turning clockwise until themask distorts.


2-65

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-24. INTERNAL DRINK TUBE NIPPLE

THIS TASK COVERS: a. Verification b. Removal b. Installation

INITIAL SETUP:


a. VERIFICATION

NOTEThis procedure can only be performed if the internal drink tubenipple on the mask has already been replaced

1. Check the internal drink tube nipple.

2. If the mask has the original drink tube nipple (1), the internal drink tube nipple cannot be replaced. Turn in thefacepiece.

3. If the mask has the revised internal drink tube nipple (2), the internal drink tube nipple can be replaced. Proceed tothe REMOVAL section of this task.

2-66

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

b. REMOVAL


• Use the allen wrench to remove the revised internal drink tube nipple by turning counterclockwise.

c. INSTALLATION

1. Position the revised internal drink tube nipple and screw in by hand.

2. Use the alien wrench to tighten the revised internal drink tube nipple.


2-67

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

COMMON (CONT)

2-25. OPTICAL INSERT KIT

THIS TASK COVERS: a. Optical Inserts (Wire) b. Optical Inserts (Plastic)Removal RemovalInstallation Installation

Adjustment

INITIAL SETUP:


Tools:Screwdriver (item 13, app D)

a. OPTICAL INSERTS (WIRE)

REMOVAL

Grasp center of wire frame (1) and pull from mask assembly (2).

INSTALLATION

NOTERemove neutral gray protective outserts prior to installing oradjusting optical insert.

Remove hood and pull head harness over the front of the mask.

1. Place wire optical inserts (3) in mask assembly with tips of upper portion (4) of wire frame pointing toward you.

2. Insert lower portion (5) of wire frame into bottom of lens cavities.

NOTEIf tips of upper portion of the wire frame protrude into the line ofsight, bend out of vision field as required.

3. Insert upper portion of wire frame into top of lens cavities.

2-68

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

NOTEThere are four retainers in each lens opening, one on each side,one at the top and one at the bottom.

4. Locate the four retainers (6) within each lens opening (External view of mask lens opening is provided for clarity).

5. Ensure that wire frame is seated behind the four retainers in each lens opening.

b. OPTICAL INSERTS (PLASTIC)

REMOVAL

1. For routine removal:

a. Fold one lens up and loosen lens carrier set screw (7).

b. Fold other lens up and loosen second lens carrier set screw (8).

c. Remove lens carrier (9) from mount frame (10) by sliding up.

d. Grasp the mount frame at the center (11) and pull to remove.

2-69

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

COMMON (CONT)

2-25. OPTICAL INSERT KIT (Cont)

b. OPTICAL INSERTS (PLASTIC) (Cont)

REMOVAL (Cont)

2. For non-routine removal:

Grasp the lens carrier (9) and pull from the mask. If the lens carrier separates from the mount frame (10), grasp thecenter (11) of the mount frame and pull to remove.

INSTALLATION

NOTERemove neutral gray protective outserts prior to installing oradjusting optical insert. Remove hood and pull head harnessover the front the mask.

Some masks have smaller lens wells and will require extra effortin aligning and connecting the hoop ends.

1. Place the mount frame into the mask assembly (2).

2. Position the center block between the mask lenses, and press into place on bridge of mask.

2-70

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

NOTEThere are four retainers in each lens opening, one on each side,one at the top and one at the bottom.

3. Locate the four retainers (6) within each lens opening (External view of mask lens opening is provided for clarity).

4. Ensure that mount frame is seated behind the four retainers in each lens opening.

5. Position mount hoops (12) into the mask lens cavities.

6. Turn mask over and do the next step looking through the eyelens.

7. Spread apart the top and bottom of the hoops until the ends of the mount hoops lock into place.

NOTEBefore attempting to install the prescription lens carrier, loosenthe set screws until the points are flush with the surface of themount block.

8. The lens carrier (9) is installed by alining the carrier's mounting block (13) with the groove (14) of the mount frame(10) and sliding the carrier into place.

2-71

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

COMMON (CONT)

2-25. OPTICAL INSERT KIT (Cont)

b. OPTICAL INSERTS (PLASTIC) (Cont)

ADJUSTMENT

1. The vertical height of the lens carrier (9) can be adjusted by sliding the carrier upward or downward.

CAUTIONDo not over tighten the set screws or the lens carrier will pop out during use.

2. Following adjustment, secure the lens carrier by tightening the set screws until contact is made with the mountframe(10).

a. Fold the lens carrier to one side and tighten the set screw (7).

b. Fold the lens carrier to the other side and tighten the second set screw (8).

2-72

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

M40A1 PECULIAR

2-26. M40A1 FACEPIECE.


INITIAL SETUP:

Applicable Configurations:M40A1

Equipment Condition:None

a. REMOVAL


1. Remove and save outserts (see Operator's Manual).

2. Remove and save Optical Insert Kit, if installed (para 2-25).

3. Remove and save filter canister (see Operator's Manual).

4. Remove and save the quick doff hood (see Operator's Manual).

5. Remove and save the universal second skin (see Operator's Manual).

b. INSTALLATIONCAUTION


1. Install the universal second skin (see Operator's Manual).

2 Install the quick doff hood (see Operator's Manual).

2. Install filter canister (see Operator's Manual).

3. Install Optical Insert Kit, if required. (para 2-25)

4. Install outserts (see Operator's Manual).

5. Return to paragraph 2-7 to adjust mask assembly at initial fitting.

2-73

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

M42A2 PECULIAR

2-27. M42A2 FACEPIECE.


INITIAL SETUP:


Equipment Condition:None

a. REMOVAL


1. Remove and save outserts (see Operator's Manual).

2. Remove and save Optical Insert Kit, if installed (para 2-25).

3. Remove and save hose assembly and filter canister (see Operator's Manual).

4. Remove and save detachable microphone (see Operator's Manual).

5. Remove and save universal second skin (see Operator's Manual).

6. Remove and save the quick doff hood (see Operator's Manual).

b. INSTALLATIONCAUTION


1. Install universal second skin (see Operator's Manual).

2 Install the quick doff hood (see Operator's Manual).

3. Install detachable microphone (see Operator's Manual).

4. Install hose assembly and filter canister (see Operator's Manual).

5. Install Optical Insert Kit, if required (para 2-25).

6 Install outserts (see Operator's Manual).

7. Return to paragraph 2-7 to adjust mask assembly at initial fitting.

2-74

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-28. CLAMP COVER


INITIAL SETUP:


a. REMOVAL

1. Pull up on flange of clamp cover (1) and work clamp cover free from hose (2).

2. Work clamp cover off end of hose.

b. INSTALLATION

1. Work clamp cover over end of hose.

2. Pull up on flange of clamp cover and position clamp cover over hose. Make sure that clamp cover fully covers endof hose.

2-75

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2


2-29. PORT GASKET


INITIAL SETUP:


a. REMOVAL

1. Remove filter canister. (See Operator's Manual)

2. Remove gasket (1) from hose end (2).

b. INSTALLATION

1. Install gasket in hose end. Make sure gasket is fully seated in hose end.

2. Install filter canister. (See Operator's Manual)


2-76

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

SECTION VIII. CLEANING AND SANITIZING

2-30. CLEANING M40A1

THIS TASK COVERS: a. Cleaning M40A1 mask assembly b. Cleaning improved field mask carrier

INITIAL SETUP:


References:TM 3-4240-346-10

Materials/Parts:Cheesecloth (item 7, app D)Gloves (item 8, app D)Isopropyl alcohol (item 9, app D)Lens brush (item 2, app D)Optical lens cleaning compound (item 6, app D)Pail (item 12, app D)Scrub brush (item 3, app D)Soap (item 15, app D)

a. CLEANG M40A1 MASK ASSEMBLY

CAUTIONDO NOT use hot or boiling water to clean the mask. Damage tothe mask may result. Use warm (comfortable to the touch)water.

NOTEMasks are to be cleaned as often as is required. However,MASK MUST BE CLEANED AND SANITIZED BEFORETRANSFERG TO ANOTHER SOLDIER.

Use only potable water to clean mask.

Cleaning may be performed by the operator but must be closelysupervised and inspected by the NBC NCO or other trainedpersonnel.

2-77

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-30. CLEANING M40A1 (Cont)

a. CLEANING M40A1 MASK ASSEMBLY (Cont)

1. Remove mask assembly from the mask carrier.

2. Remove filter canister, quick doff hood, universal second skin and outserts (see Operator's Manual) or second skin(see Operator's Manual) or universal second skin (USMC only) (see Operator's Manual).

3. Remove outlet valve cover and outlet valve disk (para 2-22).

4. Remove greasy or oily substances from mask assembly (1) with isopropyl alcohol (item 9, app D) on a cheesecloth(item 7, app D).

5. There are two methods of cleaning. The first is for light cleaning after normal operations; the second is for heavycleaning after extensive use.

a. Light cleaning

(1) Dip cheesecloth (item 7, app D) in warm soapy water and wring cloth almost dry. Lens brush may also beused. Clean mask assembly, universal second skin (2), quick doff hood (3), or second skin (4) or universalsecond skin (USMC only) (5), outlet valve cover (6), outlet valve disk (7) and one-piece hood (8) inside andout with the cheesecloth (item 7, app D).

(2) Rinse by wiping with cheesecloth (item 7, app D) that has been dipped in warm clear water and wrungalmost dry.

b. Heavy cleaning

(1) Remove head harness (9) (para 2-17).

(2) The NBC NCO will provide a pail (item 12, app D) with warm (comfortable to the touch) water for cleaningmask components. (If the NBC NCO feels it is necessary, a pail with soap and water may be provided forcleaning and a pail of water will be provided for rinsing the mask components.)

2-78

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

(3) Immerse the facepiece (10), outlet valve cover (6), outlet valve disk (7), universal second skin (2), quickdoff hood (3), or second skin (4), or universal second skin (USMC only) (5), or the one-piece hood (8) andagitate until all sand and dirt has been removed.

(4) Rinse in clear, warm water.

6. Dry facepiece (10), universal second skin (2), quick doff hood (3), or second skin (4) or universal second skin(USMC only) (5), outlet valve cover (6), outlet valve disk (7) and one-piece hood (8) with cheesecloth (item 7,app D) or allow to air dry.

7. Clean eyelens (11) and outserts (12) with soap (item 15, app D) and water or optical lens cleaning compound(item 6, app D).

8. Clean the drinking system. Fill the canteen (13) with water, loosen the M1 canteen cap (14), connect the externaldrink tube (15) to the M1 canteen cap, hold the mask upside down with the internal drink tube (16) facing awayfrom the mask and allow water to flow through the drinking system. Repeat the process twice.

NOTEIf you are sanitizing the mask, DO NOT reinstall anycomponents. Go to paragraph 2-31, Sanitizing M40A1.

9. Install universal second skin (2) and quick doff hood (3) (See Operator's Manual) or second skin (4) (seeOperator's Manual) or universal second skin (USMC only) (5) (see Operator's Manual) when used with hoodedovergarment.

10. Install clear outserts (See Operator's Manual).11. Install outlet valve cover and outlet valve disk (para 2-22).12. Install filter canister (See Operator's Manual).

2-79

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-30. CLEANING M40A1 (CONT)

b. CLEANING FIELD MASK CARRIER

CAUTION

Do not use hot water, bleach, or detergents, or soak or immersemask carrier to clean it.

1. Empty pockets and contents from improved field mask carrier (17) or field mask carrier (18).

2. Shake improved field mask carrier or field mask carrier upside down to remove dirt and foreign matter.

3. The field mask carrier cannot be turned inside out. Reach into the carrier with a dry brush (item 3, app D) toremove as much loose dirt, sand, and foreign matter as possible.

4. Turn the improved field mask carrier inside out. Use a dry brush (item 3, app D) to clean dirt, sand, and foreignmatter from the inside of the improved field mask carrier. Make sure you clean the pockets an seams.

5. Turn the improved field mask carrier right side out.

6. Use a dry brush (item 3, app D) to remove excess dirt, sand, and foreign matter from the exterior of the improvedfield mask carrier or the field mask carrier.

7. Soak brush (item 3, app D) in pail (item 12, app D) of cool water.

8. Shake brush (item 3, app D) to remove excess water.

9. Clean improved field mask carrier or field mask carrier with brush (item 3, app D) and cool water.

NOTEIf you are sanitizing the mask, DO NOT repack the mask carrier.

10. Insure improved field mask carrier or field mask carrier and mask components are completely dry before repackingmask.

2-80

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-31. SANITIZING M40A1

THIS TASK COVERS: Sanitizing M40A1 mask assembly

INITIAL SETUP:


References:TM 3-4240-346-10

Materials/Parts:Head HarnessInternal Drink TubeOutlet Valve DiskCalcium Hypochlorite (item 5, app D)Cheesecloth (item 7, app D)Gloves (item 8, app D)Pail (item 12, app D)

SANITIZING M40A1 MASK ASSEMBLY

WARNINGWear gloves to protect hands.

NOTEWHEN YOU SANITIZE A MASK, USE ONLY POTABLEWATER.

SANITIZING IS REQUIRED BEFORE MASK ISTRANSFERRED TO ANOTHER SOLDIER AND WHENTHE MASK IS TURNED IN AS SERVICEABLEEXCESS.

Sanitizing may be performed by the operator but mustbe closely supervised and inspected by the NBC NCO orother trained personnel.

THE MASK MUST BE CLEANED PRIOR TOSANITIZING. GO TO PARAGRAPH 2-34, CLEANINGM40A1 MASK AND MASK CARRIER.

1. Remove head harness (para 2-19) and discard.

2. Remove airflow deflector, inlet valve disk and inlet valve body (para 2-21)

3. Remove nosecup valve disks. (para 2-20).

2-81

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-31. SANITIZING M40A1 (CONT)

SANITIZING M40A1 MASK ASSEMBLY (CONT)

NOTEDO NOT remove internal drink tube if mask is to beretained by the same soldier. Sanitize installed internaldrink tube using steps 7 through 20. Remove anddiscard the internal drink tube only if the mask is to bereissued to another soldier.

4. Remove internal drink tube (para 2-17) and discard.

5. Remove outlet valve disk (para 2-22 ) and discard.

NOTEPrepare enough sanitizing solution to cover facepiece.

6. Add level 1/2 teaspoon of calcium hypochlorite (item 5, app D) to each gallon of clean water in a utility pail (item12, app D).

WARNINGAssure that calcium hypochlorite if fully dissolved.Drinking system can be damaged resulting in leaks andhazard to personnel.

7. Mix thoroughly for 30 seconds to dissolve calcium hypochlorite.

8. Remove M1 canteen cap (1) and fill canteen (2) with this solution and put M1 canteen cap on canteen.

9. Save the rest of the solution for sanitizing the facepiece (3).

10. Open protective cover on M1 canteen cap. Position facepiece face-up.

11. Attach quick disconnect coupling (4) to M1 canteen cap.

12. Invert canteen above facepiece. Squeeze canteen to force the sanitizing solution through the quick disconnectcoupling .

13. Lower canteen to upright position or squeeze sides to vent canteen. Use entire contents and rinse twice with clearwater in the same manner.

2-82

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

14. Immerse facepiece (3), outserts (5), airflow deflector (6), outlet valve cover (7), one piece hood (8), quick doffhood (9), second skin (10) or universal second skin (11) or universal second skin (USMC only) (12) and agitate for5 minutes in sanitizing solution.

2-83

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2



15. Rinse twice in clear warm water, agitating 2 or 3 minutes each time.

16. Connect Ml canteen cap (I) to the quick disconnect coupling (4) to drain excess water.

17. Dry all parts with cheesecloth (item 7, app D) or allow to air dry.

NOTEDiscard head harness, outlet valve disks, and internaldrink tube and replace with new parts.

CAUTIONInsure all the mask components are completely drybefore reassembling mask.

18. Install head harness (para 2-19).

19. Install inlet valve disk, inlet valve body, and airflow deflector (para 2-21).

20. Install outlet valve disk (para 2-22).

21. Install nosecup valve disk (para 2-20).

22. Install internal drink tube (para 2-17).

23. Install remaining items on mask and repack mask carrier (Operator's Manual).

2-84

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-32. CLEANING M42A2

THIS TASK COVERS: a. Cleaning M42A2 mask assembly b. Cleaning mask carrier

INTIAL SETUP:


References:TM 3-4240-346- 10

Materials/Parts:Cheesecloth (item 7, app D)Gloves (item 8, app D)Isopropyl alcohol (item 9, app D)Lens brush (item 2, app D)Optical lens cleaning compound (item 6, app D)Pail (item 12, app D)Scrub brush (item 3, app D)Soap (item 15, app D)

a. CLEANING M42A2 MASK ASSEMBLY

CAUTIONDO NOT use hot or boiling water to clean the mask.Damage to the mask may result. Use warm (comfortableto the touch) water.

NOTEMasks are to be cleaned as often as is required.However, MASK MUST BE CLEANED AND SANITIZEDBEFORE TRANSFERRINGTO ANOTHER SOLDIER.

Use only potable water to clean mask. Cleaning may beperformed by the operator but must be closelysupervised and inspected by the NBC NCO or othertrained personnel.

2-85

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2


a. CLEANING M42A2 MASK ASSEMBLY (CONT)

1. Remove mask assembly from the mask carrier.

2. Remove canister carrier, hose, quick doff hood, universal second skin, and outserts (see Operator's Manual) orsecond skin (see Operator's Manual), or universal second skin (USMC only) (see Operator's Manual).

3. Remove detachable microphone (see Operator's Manual) outlet valve cover and outlet valve disk (para 2-22).

4. Remove greasy or oily substances from mask assembly (1) with isopropyl alcohol on a cheesecloth (item 7, appD).

5. There are two methods of cleaning. The first is for light cleaning after normal operations; the second is for heavycleaning after extensive use.

a. Light cleaning

(1) Dip cheesecloth in warm soapy water and wring cloth almost dry. Lens brush may also be used. Cleanmask assembly, universal second skin (2), quick doff hood (3) or second skin (4) or universal second skin(USMC only) (5), outlet valve cover (6), outlet valve disk (7), improved canister carrier (8), detachablemicrophone (9), and one piece hood (10) inside and out with the cheesecloth (item 7, app D).

(2) Rinse by wiping with cheesecloth (item 7, app D) that has been dipped in warm clear water and wrungalmost dry.

2-86

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

b. Heavy cleaning

(1) Remove head harness (para 2-17).

(2) The NBC NCO will provide a pail with warm (comfortable to the touch) water for cleaning maskcomponents. (If the NBC NCO feels it is necessary, a pail (item 3, app D), with soap and water may beprovided for cleaning and a pail of water will be provided for rinsing the mask components.)

(3) Dip cheesecloth (item 7, app D) in warm soapy water and wring cloth almost dry. Lens brush may also beused. Clean head harness (10) and detachable microphone (9).

(4) Immerse the facepiece (11), universal second skin (2), quick doff hood (3) or second skin (4) or universalsecond skin (USMC only) (5), outlet valve cover (6), outlet valve disk (7), improved canister carrier (8) orone-piece hood (10) and agitate until all dirt, sand, and foreign matter has been removed.

(5) Rinse in clear, warm water.

6. Dry facepiece (11), head harness ( 12), universal second skin (2), quick doff hood (3) or second skin (4) oruniversal second skin (USMC only) (5), outlet valve cover (6), outlet valve disk (7), improved canister carrier (8),detachable microphone (9), and one piece hood (10) with cheesecloth (item 7, app D) or allow to air dry.

2-87

TM 3-4240-346-20&PTM 09204A/09205A - 20&Pn/2


a. CLEANING M42A2 MASK ASSEMBLY (CONT)

7. Wipe outside of hose (12) with isopropyl alcohol (item 9, App D) on a cheesecloth.

8. Clean eyelens (13) and outserts (14) with soap (item 15, app D) and water or optical lens cleaning compound(item 6, app D).

9. Clean the drinking system. Fill the canteen (15) with water, loosen the M1 canteen cap (16), connect the externaldrink tube (17) to the M1 canteen cap, hold the mask upside down with the internal drink tube (18) facing awayfrom the mask and allow water to flow through the drinking system. Repeat the process twice.

2-88

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

NOTEIf you are sanitizing the mask. DO NOT reinstall anycomponents. Go to paragraph 2-33, Sanitizing M42A2.

10. Install universal second skin (2) and quick doff hood (3) (See Operator's Manual) or universal second skin (4) (seeOperator's Manual) or universal second skin (USMC only) (5) (see Operator's Manual) when used with hoodedovergarment.

11. Install clear outserts (See Operator's Manual).

12. Install outlet valve cover, and outlet valve disk (para 2-22).

13. Install universal second skin (3), or second skin (4), or universal second skin (USMC only) (5) and quick doff hood(3) (See Operator's Manual).

14. Install improved canister carrier and hose assembly (See Operator's Manual).

15. Install detachable microphone (see Operator's Manual).

2-89

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2


b. CLEANING MASK CARRIER

CAUTIONDo not use hot water, bleach, or detergents, or soak orimmerse mask carrier to clean it.

1. Empty pockets and contents from combat vehicle mask carrier (19) or field mask carrier (20).

2. Shake combat vehicle mask carrier or field mask carrier upside down to remove dirt and foreign matter.

3. The field mask carrier cannot be turned inside out. Reach into the carrier with a dry brush (item 3, app D) toremove as much loose dirt, sand, and foreign matter as possible.

4. Turn the combat vehicle mask carrier inside out. Use a dry brush (item 3, app D) to clean dirt, sand, and foreignmatter from the inside of the combat vehicle mask carrier. Make sure you clean the pockets and seams.

5. Turn the combat vehicle mask carrier right side out.

6. Use a dry brush (item 3, app D) to remove excess dirt, sand, and foreign matter from the exterior of the combatvehicle mask carrier or the field mask carrier.

7. Soak brush (item 3, app D) in pail (item 12, app D) of cool water.

8. Shake brush (item 3, app D) to remove excess water.

9. Clean combat vehicle mask carrier or field mask carrier with brush (item 3, app D) and cool water.

NOTEIf you are sanitizing the mask, do not repack the maskcarrier.

10. Insure combat vehicle mask carrier or field mask carrier and mask components are completely dry beforerepacking

2-90

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-33. SANITIZING M42A2

THIS TASK COVERS: Sanitizing M42A2 mask assembly

INITIAL SETUP:


References:TM 3-4240-346- 10

Materials/Parts:Head HarnessInternal Drink TubeOutlet Valve DiskCalcium Hypochlorite (item 5, app D)Cheesecloth (item 7, app D)Gloves (item 8, app D)Pail (item 12, app D)

SANITIZING M42A2 MASK ASSEMBLY

WARNINGWear gloves to protect hands.

NOTEWHEN YOU SANITIZE A MASK, USE ONLY POTABLEWATER.

SANITIZING IS REQUIRED BEFORE MASK ISTRANSFERRED TO ANOTHER SOLDIER ANDWHENTHE MASKIS TURNED IN AS SERVICEABLEEXCESS.

Sanitizing may be performed by the operator but mustbe closely supervised and inspected by the NBC NCO orother trained personnel.

THE MASK MUST BE CLEANED PRIOR TOSANITIZING. GO TO PARAGRAPH 2-36, CLEANINGM42A2 MASK AND MASK CARRIER.

1. Remove head harness (para 2-19) and discard.

2. Remove airflow deflector, inlet valve disk and inlet valve body (para 2-21)

3. Remove nosecup valve disks. (para 2-20).

2-91

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2



NOTEDO NOT remove internal drink tube if mask is to beretained by the same soldier. Sanitize installed internaldrink tube using steps 7 through 20. Remove anddiscard the internal drink tube only if the mask is to bereissued to another soldier.

4. Remove internal drink tube (para 2-17) and discard.

5. Remove outlet valve disk (para 2-22) and discard.

CAUTIONSet detachable microphone aside so that it does not getwet or damaged.

6. Remove and save the detachable microphone (See Operator's Manual).NOTE

Prepare enough sanitizing solution to cover facepiece.

7. Add level 1/2 teaspoon of calcium hypochlorite (item 5, app D) to each gallon of clean water in a utility pail (item12, app D).

WARNINGAssure that calcium hypochlorite is fully dissolved.Drinking system can be damaged resulting in leaks andhazard to personnel.

8 Mix thoroughly for 30 seconds to dissolve calcium hypochlorite.

9. Remove M1 canteen cap (1) and fill canteen (2) with this solution and put M1 canteen cap on canteen.

10. Save the rest of the solution for sanitizing the facepiece (3).

11. Open protective cover on M1 canteen cap. Position facepiece face-up.

2-92

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

12. Attach quick disconnect coupling (4) to M1 canteen cap.

13. Invert canteen above facepiece. Squeeze canteen to force the sanitizing solution through the quick disconnectcoupling.

14. Lower canteen to upright position or squeeze sides to vent canteen. Use entire contents and rinse twice with clearwater in the same manner.

15. Immerse facepiece (3), outserts (5), airflow deflector (6), outlet valve cover (7), quick doff hood (8), universalsecond skin (9) or second skin (10) or universal second skin (USMC only) (11), or one-piece hood (12) and agitatefor 5 minutes in sanitizing solution.

2-93

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2


SANITIZING M42A2 MASKASSEMBLY (CONT)

16. Rinse twice in clear warm water, agitating 2 or 3 minutes each time.

17. Connect M1 canteen cap (1) to the quick disconnect coupling (4) to drain excess water.

18. Dry all parts with cheesecloth (item 7, app D) or allow to air dry.

NOTEDiscard head harness, outlet valve disks, and internaldrink tube and replace with new parts.

CAUTIONInsure all the mask components are completely drybefore reassembling mask.

19. Install head harness (para 2-19).

20. Install inlet valve disk, inlet valve body, and airflow deflector (para 2-21).

21. Install outlet valve disk (para 2-22).

22. Install nosecup valve disk (para 2-20).

23. Install internal drinktube (para 2-17).

24. Install remaining items on mask and repack mask carrier (Operator's Manual).

2-94

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

SECTION IX. PREPARATION FOR STORAGE OR SHIPMENT2-34. PREPARATION FOR STORAGE OR SHIPMENT

CAUTIONStore masks in a cool dry place. Heat and moisture willdamage the mask and the filter material.

a. Preparation for storage or shipment instructions are identical for the M40A1 and the M42A2, except for paragraphreferences. The appropriate references for cleaning or performing other functions are identified by mask.

b. Storage by Using Unit. Use either the fiberboard boxes or the plywood boxes for unit storage by stacking them ontheir sides to form a bank of storage cells. Fiberboard boxes should not be stacked more than three high.

c. Faceform. Replace interior plastic faceform packaging support if mask will be stowed longer than 30 days.

d. Temporary Storage by Using Unit.

1. Hang the carrier either by the shoulder strap or by the D-ring on the short strap on top of the carrier.

2. Stow straps as directed by the local unit SOP. Both straps may be hooked to the D-ring by their snaphooks.

e. Shipment of mask assembly.

WARNINGHEALTH/ENVIRONMENTAL HAZARD

• There are two Mask Filter Canisters, the C2 and theC2A1.

• The C2 canister contains Chromium VI and damagedor unusable canisters are considered HazardousWaste. (Chromium VI is a known carcinogen ifinhaled or swallowed.)

• The C2A1 canister is chromium-free but mustcontinue to be disposed of in accordance with Stateand Local Environmental Laws.

• DO NOT throw away damaged or unusable canistersas ordinary trash.

• DO turn in damaged or unusable canisters to yourhazardous waste management office or DefenseReutilization and Marketing Office (DRMO).

CAUTIONPackage mask carefully to prevent damage duringshipment.

1. Clean masks (M40A1 - para 2-30), (M42A2 - para 2-32).2 Do not ship canister with mask. Turn canisters in to DRMO or, in accordance with state and local environmental

laws, unit SOP, for disposal.3. Install clear outserts onto lens of mask facepiece. Place operator's manual into a ziplock bag and close. Stow

other outserts, waterproof bag and packaged operator's manual in inside pockets of carrier.4. Pull hood over the front of the mask facepiece.5. Loosen head harness straps and install packaging faceform into mask facepiece cavity. Tighten the head harness

straps evenly around faceform.6. Wrap mask facepiece with one complete turn of cushioning material (item 19 app D). Overlap and secure ends

with tape (item 20, app D).

2-95

TM 3-4240-346-20&PTM 09204A/09205A - 20&P/2

2-34. PREPARATION FOR STORAGE OR SHIPMENT (CONT)

7. Install wrapped mask facepiece in the carrier with lenses facing upward and close flaps tightly.8. Place, carriers, packaged as above, (maximum 8 each) in one layer into a weather-resistant shipping container

(item 18, app D) or equivalent. The voids in box shall be filled with cushioning material (item 19, app D).9. Pack the shipping container into a wooden shipping container (item 18, app D). Use six cleated box fasteners to

secure box lid, applying two on each side and one on each end.10. Secure a shipping document envelope on the side on the shipping container with an enclosed DD Form 134 for

each NSN being shipped (AR 725-50, See II, Par 7-11).

f. Shipment of facepiece.

CAUTIONPackage mask carefully to prevent damage duringshipment.

1. Clean facepiece (M40A1 - para 2-30), (M42A2 - para 2-32).2. Loosen head harness straps and install packaging faceform into mask facepiece cavity. Tighten the head harness

straps evenly around faceform.3. Wrap mask facepiece with one complete turn of cushioning material (item 19 app D). Overlap and secure ends

with tape (item 20, app D).4. Place, carriers, packaged as above, (maximum 8 each) in one layer into a weather-resistant shipping container

(item 18, app D) or equivalent. The voids in box shall be filled with cushioning material (item 19, app D).5. Secure a shipping document envelope on the side on the shipping container with an enclosed DD Form 134 for

each NSN being shipped (AR 725-50, See II, Par 7-11).

2-96

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

APPENDIX A

REFERENCES

A-1. SCOPE

This appendix lists all forms, field manuals, technical manuals, and miscellaneous publications referenced in this manual.

A-2. FORMS

DA Form 2028 .................................................................................. Recommended Changes to Publications andBlank Forms

DA Form 2028-2 ............................................................................... Recommended Changes to Equipment TechnicalPublications

DA Form 2404 .................................................................................. Equipment Inspection and MaintenanceWorksheet

DD Form 314 .................................................................................... Preventive Maintenance Schedule and RecordNAVMC Form 10772......................................................................... Recommended Change to

Publications/Logistics-Maintenance Data CodingSF 364.............................................................................................. Report of Discrepancy (ROD)SF 368.............................................................................................. Product Quality Deficiency Report

A-3. FIELD MANUALS

FM 3-4 .............................................................................................. NBC ProtectionFM 21-11 .......................................................................................... First Aid for Soldiers

A-4. TECHNICAL MANUALS

TM 3-4240-346-10 ............................................................................ Chemical-Biological Mask: Field M40A1, CombatVehicle M42A2

TM 43-0002-31 ................................................................................. Destruction of Chemical Weapons and DefenseEquipment to Prevent Enemy Use

TM 4700-15/1 ................................................................................... Ground Equipment Record Procedures

A-5. TRAINING MATERIALS

TVT 3-90........................................................................................... M41 Protection Assessment Testing System (45minutes) - PIN 710502 - Video Tape

TVT 3-95........................................................................................... M40/M42 Protective Mask Unit Level OperationsPIN 710665 - Video Tape

TVT 3-96........................................................................................... M40/M42 Protective Mask Operator LevelOperations - PIN 710719 - Video Tape

TVT 3-97........................................................................................... M41 Protection Assessment Testing System (9.5minutes) - PIN 710411 - Video Tape

A-1

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

A-6. MISCELLANEOUS

AR 70-38 .......................................................................................... Research, Development, Test and Evaluation ofMaterial for Extreme Climatic Conditions

AR 700-84 ........................................................................................ Issue and Sale of Personal ClothingAR 725-50 ........................................................................................ Requisition, Receipt, and Issue SystemCTA 8-100 ........................................................................................ Army Medical Department Expendable/Durable

ItemsCTA 50-970 ...................................................................................... Expendable/Durable Items (Except Medical,

Class V, Repair Parts, and Heraldic items)DA PAM 738-750 .............................................................................. The Army Maintenance Management System

(TAMMS)MCO 4855.10 ................................................................................... Product Quality Deficiency Report (PQDR)MIL-STD-129 .................................................................................... Marking for Shipment and StorageSB 3-30-2 ......................................................................................... Chemical-Biological Canisters and Filter

Elements: Serviceability Lists ProtectionAssessment Test System (Provided with enditem, commercial manual)

TC 3-41 ............................................................................................ Protection Assessment Test System

A-2

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

APPENDIX B

MAINTENANCE ALLOCATION CHART (MAC)

SECTION I. INTRODUCTION

B-1. THE MAINTENANCE SYSTEM MAC.

a. Parts of the MAC of the M40A1 differ from the MAC of the M42A2. In order to stop any confusion, two separate MACsare provided. One for the M40A1 and one for the M42A2.

b. This introduction (Section I) provides a general explanation of all maintenance and repair functions authorized atvarious maintenance levels under the standard Maintenance System concept.

c. The Maintenance Allocation Chart (MAC) in Section II designates overall authority and responsibility for theperformance of maintenance functions on the identified end item or component The application of the maintenancefunctions to the end item or component will be consistent with the capacities and capabilities of the designatedmaintenance levels, which are shown on the MAC in column (4) as:

Unit - includes two subcolumns, C (operator/crew) and O (unit) maintenance.

Direct Support - includes an F subcolumn.

General Support - includes an H subcolumn.

Depot - includes a D subcolumn.

d. Section III lists the tools and test equipment (both special tools and common tool sets) required for each maintenancefunction as referenced from Section II.

e. Section IV contains supplemental instructions and explanatory notes for a particular maintenance function.

B-2. MAINTENANCE FUNCTIONS.

Maintenance functions will be limited to and defined as follows:

a. Inspect. To determine the serviceability of an item by comparing its physical, mechanical and /or electricalcharacteristics with established standards through examination (e.g., by sight, sound or feel).

b. Test. To verify serviceability by measuring the mechanical, pneumatic, hydraulic, or electrical characteristics of anitem and comparing those characteristics with prescribed standards.

c. Service. Operations required periodically to keep an item in proper operating condition; i.e. to clean (includesdecontaminate, when required), to preserve, to drain, to paint, or to replenish fuel, lubricants, chemical fluids, or gases.

d. Adjust. To maintain or regulate, within prescribed limits, by bringing into proper or exact position, or by setting theoperating characteristics to specified parameters.

e. Align. To adjust specified variable elements of an item to bring about optimum or desired performance.

f. Calibrate. To determine and cause corrections to be made or to be adjusted on instruments or test, measuring, anddiagnostic equipments used in precision measurement. Consists of comparisons of two instruments, one of which is acertified standard of known accuracy, to detect and adjust any discrepancy in the accuracy of the instrument beingcompared.

g. Remove/Install. To remove and install the same item when required to perform service or other maintenancefunctions. Install may be the act of emplacing, seating, or fixing into position a spare, repair part, or module (component orassembly) in a manner to allow the proper functioning of an equipment or system.

B-1

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

B-2. MAINTENANCE FUNCTIONS (CONT)

h. Replace. To remove an unserviceable item and install a serviceable counter part in its place. "Replace" is authorizedby the MAC and assigned maintenance level is shown as the 3rd position code of the SMR code.

i. Repair. The application of maintenance services including fault location/troubleshooting, removal/installation, anddisassembly/assembly procedures, and maintenance actions to identify troubles and restore serviceability to an item bycorrecting specific damage, fault, malfunction, or failure in a part, subassembly, module (component or assembly), enditem, or system.

j. Overhaul. That maintenance effort (service/action) prescribed to restore an item to a completelyserviceable/operational condition as required by maintenance standards in appropriate technical publications (i.e.,DMWR). Overhaul is normally the highest degree of maintenance performed by the Army. Overhaul does not normallyreturn an item to like new condition.

k. Rebuild. Consists of those services/actions necessary for the restoration of unserviceable equipment to a like newcondition in accordance with original manufacturing standards. Rebuild is the highest degree of materiel maintenanceapplied to Army equipment. The rebuild operation includes the act of returning to zero those age measurements(hours/miles, etc.) considered in classifying Army equipment/components.

B-3. EXPLANATION OF COLUMNS IN THE MAC, SECTION II.

a. Group Number. (Column(1)). Lists functional group code numbers, the purpose of which is to identify maintenancesignificant components, assemblies, subassemblies, and modules with the next higher assembly.

b. Component/Assembly.(Column(2)). Contains the item names of components, assemblies, subassemblies, andmodules for which maintenance is authorized.

c. Maintenance Function. (Column(3)). Lists the functions to be performed on the item listed in column (2).

d. Maintenance Level. (Column (4)). Specifies, each level of maintenance authorized to perform each function listed incolumn (3), by indicating work time required (expressed as man-hours in whole hours or decimals) in the appropriatesubcolumn. This work-time figure represents the active time required to perform that maintenance function at the indicatedlevel of maintenance. If the number or complexity of the tasks within the listed maintenance function vary at differentmaintenance levels, appropriate work time figures will be shown for each level. The work time figure represents theaverage time required to restore an item (assembly, subassembly, component, module, end item, or system) to aserviceable condition under typical field operating conditions. This time includes preparation time (including any necessarydisassembly/assembly time), troubleshooting/fault location time, and quality assurance/quality control time in addition tothe time required to perform the specific tasks identified for the maintenance functions authorized by the MaintenanceAllocation Chart.

The symbol designations for the various maintenance levels are as follows:

C .......................................................................Operator or Crew

O .......................................................................Unit Maintenance

F .......................................................................Direct Support Maintenance

H .......................................................................General Support Maintenance

L .......................................................................Specialized Repair Activity (SRA) (USMC - EquipmentSurveillance Unit (ESU))

D .......................................................................Depot Maintenance

e. Tools and Equipment. (Column (5)). Specifies, by code, those common tool sets (not individual tools), and specialtools, TMDE, and support equipment required to perform the designated function.

f. Remarks. (Column(6)). This column shall when applicable, contain a letter code, in alphabetic order, which shall bekeyed to the remarks contained in Section IV.

B-2

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

B-4. EXPLANATION OF COLUMNS IN TOOL AND TEST EQUIPMENT REQUIREMENTS SECTION III.

a. The tool and test equipment requirements provided in this section are identical for the M40A1 and the M42A2 masks.

b. Reference Code (Column (1)). The tool and test equipment reference code correlates with a code used in the MAC,Section II, Column (5).

c. Maintenance Level (Column (2)). The lowest level of maintenance authorized to use the tool or test equipment.

d. Nomenclature (Column (3)). Name or identification of the tool or test equipment.

e. National Stock Number. (Column (4)). National Stock Number of the tool or test equipment.

f. Tool Number. (Column (5)). The manufacturer's part number.

B-5. EXPLANATION OF COLUMNS IN REMARKS, SECTION IV.

a. This section is presently identical for the M40A1 and the M42A2 masks.

b. Reference Code (Column (2)). The code recorded in column (6), Section II.

c. Remarks (Column (2)). This column lists information pertinent to the maintenance function being performed asindicated in the MAC, Section II.

SECTION II. MAINTENANCE ALLOCATION CHARTS

CHEMICAL-BIOLOGICAL MASK: FIELD M40A1

(1) (2) (3) (4) (5) (6)

GROUPNUMBER

COMPONENT/ASSEMBLY

MAINTENANCEFUNCTION

MAINTENANCE LEVEL TOOLS ANDEQUIPMENTREF CODE

REMARKSCODE

UNIT DIRECTSUPPORT

GENERALSUPPORT

DEPOT

C O F H D

00

01

Chemical-Biological Mask:Combat Vehicle

FacepieceAssembly

InspectTestAdjustReplaceRepair

InspectTestRepairService

0.3

0.1

0.30.3

0.3

0.30.1

0.10.3

0.30.30.30.3

B-3

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

SECTION II. MAINTENANCE ALLOCATION CHARTS (CONT)

CHEMICAL-BIOLOGICAL MASK: COMBAT VEHICLE M42A2

(1) (2) (3) (4) (5) (6)

GROUPNUMBER

COMPONENT/ASSEMBLY

MAINTENANCEFUNCTION

MAINTENANCE LEVEL TOOLS ANDEQUIPMENTREF CODE

REMARKSCODE

UNIT DIRECTSUPPORT

GENERALSUPPORT

DEPOT

C O F H D

00

01

02

03

Chemical-Biological Mask:Combat Vehicle

FacepieceAssembly

Canister Carrier

Hose Assembly

InspectTestAdjustReplaceRepair

InspectTestRepairService

InspectReplaceRepair

InspectReplaceRepair

0.3

0.1

0.30.3

0.3

0.2

0.1

0.30.1

0.10.3

0.30.30.30.3

0.20.10.1

0.10.1

SECTION III. TOOL AND TEST EQUIPMENT REQUIREMENTS

TOOL OR TESTREFERENCE CODE

MAINTENANCELEVEL

NOMENCLATURE NATIONAL STOCKNUMBER

TOOL NUMBER

1 UNIT Protection AssessmentTesting System

4240-01-365-8241 5-1-3326

SECTION IV. REMARKSNot Applicable.

B-4

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

APPENDIX C

UNIT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTCurrent as of May 1998

SECTION I. INTRODUCTIONC-1. SCOPE.

This RPSTL lists and authorizes spares and repair parts; special tools; special test, measurement, and diagnosticequipment (TMDE); and other special support equipment required for performance of Unit maintenance of the M40A1 andthe M42A2 Masks. It authorizes the requisitioning, issue, and disposition of spares, repair parts and special tools asindicated by the source, maintenance and recoverability (SMR) codes.

C-2. GENERAL.

NOTE: Due to Government procurement methods, the appearance of the part you receive may differ fromthe illustrations in this TM.

This Repair Parts and Special Tools List is divided into the following sections:

a. Section II. Repair Parts List. A list of spares and repair parts authorized by this RPSTL for use in the performance ofmaintenance. The list also includes parts which must be removed for replacement of the authorized parts. Parts lists arecomposed of functional groups in ascending alphanumeric sequence with the parts in each group listed in ascendingfigure and item number sequence. Bulk materials are listed by item name in FIG. BULK at the end of the Section. Itemslisted are shown on the associated illustration.

b. Section III. Special Tools List. Not applicable.

c. Section IV. Cross-Reference Indexes. A list, in National Item Identification Number (NIIN) sequence, of all NationalStock Numbers (NSN) appearing in the listings, followed by a separate list in alphanumeric sequence of all part numbersappearing in the listings. National stock numbers and part numbers are cross-referenced to each illustration figure anditem number appearance. The figure and item number index lists figure and item numbers in alphanumeric sequence andcross-references NSN, CAGEC and part numbers.

C-3. EXPLANATION OF COLUMNS (SECTION II AND III).

a. ITEM NO. (Column (1)). Indicates the number used to identify items called out in the illustration.b. SMR Code (Column (2)). The Source, Maintenance, and Recoverability (SMR) code is a 5-position code containing

supply/requisitioning information, maintenance level authorization criteria, and disposition instruction, as shown in thefollowing breakout:

Source Maintenance Recoverabilitycode code code

1st twopositions

XX XX X

3d position 4th position

How you get an item Who can Who can do Who determined dispositionreplace, or use the complete repair* action on an unserviceable item

item on the item

*Complete Repair: Maintenance capacity, capability, and authority to perform all corrective maintenance tasks of the“Repair” function in a use/user environment in order to restore serviceability to a failed item.

C-1

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

C-3. EXPLANATION OF COLUMNS (SECTION II AND III). (CONT)

(1) Source Code. The source code tells you how to get an item needed for maintenance, repair or overhaul of an enditem/equipment. Explanation of source codes follow:

Code Explanation

PAPBPC**PDPEPFPG

KDKFKB

Explanation

Stocked items; use the applicable NSN to request/requisition items with these source codes. They areauthorized to the level indicated by the code entered inthe 3d position of the SMR code.

**NOTE: Items coded PC are subject to deterioration.

Items with these codes are not to be requested/requisi-tioned individually. They are part of a kit which is autho-rized to the maintenance level indicated in the 3dposition of the SMR code. The complete kit must berequisitioned and applied.

MO-(Made at Unit AVUM level)MF-(Made at DS/AVIM level)MH-(Made at GS level)ML-(Made at Specialized Repair Act (SRA)MD-(Made at Depot)

AO-(Assembled by Unit/AVUM level)AF-(Assembled by DS/AVIM level)AH-(Assembled at GS level)AL-(Assembled by SRA)AD-(Assembled by Depot)

Items with these codes are not to be requested/requisi-tioned individually. They must be made by bulk materialwhich is identified by the part number in the DESCRIP-TION AND USABLE ON CODE (UOC) column and listedin the Bulk Material group of the repair parts and specialtools list in this RPSTL. If the item is authorized to you bythe 3d position code of the SMR code, but the sourcecode indicates it is made at a higher level, order the itemfrom the higher level of maintenance.

Items with these codes are not to be requested/requisi-tioned individually. The parts that make up theassembled item must be requisitioned or fabricated andassembled at the level of maintenance indicated by thesource code. If the 3d position code of the SMR codeauthorizes you to replace the item, but the source codeindicates it is assembled at a higher level, order the itemfrom the higher level of maintenance.

XA-Do not requisition an "XA" coded item. Order its next higher assembly. (Also, refer to the NOTE below.)XB-If an "XB" coded item is not available from salvage, order it using the CAGEC and part number given.XC-Installation drawing, diagram, instruction sheet, field service drawing, that is identified by manufacturer's part number.XD-Item is not stocked. Order an "XD" coded item through normal supply channels using the CAGEC and part numbergiven, if no NSN is available.

NOTE: Cannibalization or controlled exchange, when authorized, maybe used as a source of supply for items with theabove source codes, except for those source coded "XA" or those aircraft support items restricted by requirements of AR750-1.

(2) Maintenance Code. Maintenance codes tell you the level(s) of maintenance authorized to USE and REPAIRsupport items. The maintenance codes are entered in the third and fourth positions of the SMR Code as follows:

C-2

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

C-3. EXPLANATION OF COLUMNS (SECTION II AND III).

(a) The maintenance code entered in the third position tells you the lowest maintenance level authorized toremove, replace, and use an item. The maintenance code entered in the third position will indicate authorization to one ofthe following levels of maintenance:

Code Application/Explanation

C -Crew or operator maintenance done within Unit or Aviation Unit Maintenance.O -Unit or Aviation Unit level can remove, replace, and use the item.F -Direct support or Aviation Intermediate level can remove, replace, and use the item.H -General support level can remove, replace, and use the item.L -Specialized repair activity can remove, replace, and use the item (USMC - Equipment Surveillance Unit (ESU)).D -Depot level can remove, replace, and use the item.

(b) The maintenance code entered in the fourth position tells whether or not the item is to be repaired andidentifies the lowest maintenance level with the capability to do complete repair (i.e., perform all authorized repairfunctions). (NOTE: Some limited repair may be done on the item at a lower level of maintenance, if authorized by theMaintenance Allocation Chart (MAC) and SMR codes). This position will contain one of the following maintenance codes.


O -Unit or Aviation Unit is the lowest level that can do complete repair of the item.F -Direct support or Aviation Intermediate is the lowest level that can do complete repair of the item.H -General support is the lowest level that can do complete repair of the item.L -Specialized repair activity (designate the specialized repair activity) is the lowest level that can do complete

repair of the item (USMC - Equipment Surveillance Unit (ESU)).D -Depot is the lowest level that can do complete repair of the item.Z -Nonreparable. No repair is authorized.B -No repair is authorized. (No parts or special tools are authorized for the maintenance of a "B" coded item).

However, the item may be reconditioned by adjusting, lubricating, etc., at the user level.

(3) Recoverability Code. Recoverability codes are assigned to items to indicate the disposition action onunserviceable items. The recoverability code is entered in the fifth position of the SMR Code as follows:


Z -Nonreparable item. When unserviceable, condemn and dispose of the item at the level of maintenance shownin 3d position of SMR code.

O -Reparable item. When uneconomically reparable, condemn and dispose of the item at the Unit or Aviation Unitlevel.

F -Reparable item. When uneconomically reparable, condemn and dispose of the item at the Direct support orAviation Intermediate level.

H -Reparable item. When uneconomically reparable, condemn and dispose of the item at the General supportlevel.

D -Reparable item. When beyond lower level repair capability, return to depot. Condemnation and disposal of itemnot authorized below Depot level.

L -Reparable item. Condemnation and disposal not authorized below Specialized Repair Activity (SRA) (USMC -Equipment Surveillance Unit (ESU)).

A -Item requires special handling or condemnation procedures because of specific reasons (e.g., precious metalcontent, high dollar value, critical material, or hazardous material). Refer to appropriate manuals/directives forspecific instructions.

c. CAGEC (Column (3)). The Commercial and Government Entity Code (CAGEC) is a 5-digit code which is used toidentify the manufacturer, distributor, or Government agency, etc., that supplies the item.

C-3

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

C-3. EXPLANATION OF COLUMNS (SECTION II AND III). (CONT)

d. PART NUMBER (Column (4)). Indicates the primary number used by the manufacturer (individual, company, firm,corporation, or Government activity), which controls the design and characteristics of the item by means of its engineeringdrawings, specifications standards, and inspection requirements to identify an item or range of items.

NOTE: When you use an NSN to requisition an item, the item you receive may have a different part number fromthe part ordered.

e. DESCRIPTION AND USABLE ON CODE (UOC) (Column (5)). This column includes the following information:

(1)The Federal item name and, when required, a minimum description to identify the item.

(2)The usable on code, when applicable. (See para. C-5, Special Information.)

(3)The statement "END OF FIGURE" appears just below the last item description in Column 5 for a given figure inboth Section II and Section III.

f. QTY. (Column (6)). The QTY (quantity per figure column) indicates the quantity of the item used in the breakoutshown on the illustration figure, which is prepared for a functional group, subfunction group, or an assembly. A "V"appearing in this column in lieu of a quantity indicates that the quantity is variable and the quantity may vary fromapplication to application.

C-4. EXPLANATION OF COLUMNS (Section IV).

a. NATIONAL STOCKNUMBER (NSN) INDEX.

(1) STOCK NUMBER column. This column lists the NSN by National Item Identification Number (NIIN) sequence.The NIIN consists of the last nine digits of the NSN. (i.e.,NSN )

5305-01-674-1467NIIN

When using this column to locate an item, ignore the first 4 digits of the NSN. However, the complete NSN should be usedwhen ordering items by stock number.

(2) FIG. column. This column lists the number of the figure where the item is identified/located. The figures are innumerical order in Section II and III.

(3) ITEM column. The item number identifies the item associated with the figure listed in the adjacent FIG. column.This item is also identified by the NSN listed on the same line.

b. PART NUMBER INDEX. Part numbers in this index are listed by part number in ascending alphanumeric sequence(i.e., vertical arrangement of letter and number combination which places the first letter or digit of each group in order Athrough Z, followed by the numbers 0 through 9 and each following letter or digit in like order).

(1) CAGEC column. The Commercial and Government Entity Code (CAGEC) is a 5-digit code used to identify themanufacturer, distributor, or Government agency, etc., that supplies the item.

(2) PART NUMBER column. Indicates the primary number used by the manufacturer (individual, firm, corporation, orGovernment activity), which controls the design and characteristics of the item by means of its engineering drawings,specifications standards, and inspection requirements to identify an item or range of items.

(3) STOCK NUMBER column. This column lists the NSN for the associated part number and manufacturer identifiedin the PART NUMBER and CAGEC columns to the left.

(4) FIG. column. This column lists the number of the figure where the item is identified/located in Section II and Ill.

(5) ITEM column. The item number is that number assigned to the item as it appears in the figure referenced in theadjacent figure number column.

c. FIGURE AND ITEM NUMBER INDEX

(1) FIG. column. This column lists the number of the figure where the item is identified/located in Section II and III.

C-4

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

C-4. EXPLANATION OF COLUMNS (SECTION IV).

(2) ITEM column. The item number is that number assigned to the item as it appears in the figure referenced in theadjacent figure number column.

(3) STOCK NUMBER column. This column lists the NSN for the item.

(4) CAGEC column. The Commercial and Government Entity Code (CAGEC) is a 5-digit code used to identify themanufacturer, distributor, or Government agency, etc., that supplies the item.

(5) PART NUMBER column. Indicates the primary number used by the manufacturer (individual, firm, corporation, orGovernment activity), which controls the design and characteristics of the item by means of its engineering drawings,specification standards, and inspection requirements to identify an item or range of items.

C-5. SPECIAL INFORMATION.

a. USABLE ON CODE. The usable on code appears in the lower left corner of the Description Column heading. Usableon codes are shown as "UOC:..." in the Description Column (justified left) on the first line of the applicable itemdescription/nomenclature. Uncoded items are applicable to all models. Identification of the usable on codes used in theRPSTL are:

Code Used On

Y73 M40A1FieldMask(Sm.)7Y3 M40A1 Field Mask (Med.)73Y M40A1 Field Mask (Lg.)213 M42A2 Combat Vehicle Mask (Sm.)21M M42A2 Combat Vehicle Mask (Med.)21L M42A2 Combat Vehicle Mask (Lg.)

C-6. HOW TO LOCATE REPAIR PARTS.

a. When National Stock Number or Part Number is Not Known.

(1) First. Using the table of contents, determine the functional group or subfunctional group to which the item belongs.This is necessary since figures are prepared for functional groups and subfunctional groups, and listings are divided intothe same groups.

(2) Second. Find the figure covering the functional group or subfunctional group to which the item belongs.

(3) Third. Identify the item on the figure and use the Figure and Item Number Index to find the NSN.

b. When National Stock Number or Part Number is Known.

(1) First Using the National Stock Number or Part Number Index, find the pertinent National Stock Number or PartNumber. The NSN index is in National Item Identification Number (NIIN) sequence. (see C-4.a(l)). The part numbers in thePart Number Index are listed in ascending alphanumeric sequence (see C-4.b). Both indexes cross-reference you to theillustration/figure and item number of the item you are looking for.

(2) Second. Turn to the figure and item number, verify that the item is the one you're looking for, then locate the itemnumber in the repair parts list for the figure.

C-7. ABBREVIATIONS. Not applicable.

C-5

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

SECTION II

Figure C-1. Chemical Biological Mask: Field M40A1

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

(1) (2) (3) (4) (5) (6)ITEM SMR PARTNO. CODE CAGEC NUMBER DESCRIPTION AND USABLE CODES (UOC) QTY

GROUP 00: CHEMICAL BIOLOGICAL MASK:FIELD M40A1

FIGURE C-1. CHEMICAL BIOLOGICAL MASK

1 PAODD 81361 5-1-1001-10 FACEPIECE ASSEMBLY..............................................1UOC: Y73

1 PAODD 81361 5-1-1001-20 FACEPIECE ASSEMBLY..............................................1UOC: 7Y3

1 PAODD 81361 5-1-1001-30 FACEPIECE ASSEMBLY..............................................1UOC: 73Y

2 PAOZZ 81361 5-1-1545-20 OUTSERTS, NEUTRAL ................................................13 PAOZZ 81361 5-1-1545-10 OUTSERTS, CLEAR.....................................................14 PAOZZ 81361 5-1-2775 CARRIER ASSY ...........................................................15 PCOZA 81361 5-3-1520 FILTER CANISTER, CHEMICAL...................................16 PAOZZ 81349 MILB51170 BAG, WATERPROOFING, C ........................................17 PCOZZ 81361 5-1-1003 FACEFORM PACKAGING............................................18 PCOZZ 81361 5-1-27-7 HOOD ASSEMBLY .......................................................19 PCOZZ 81361 5-1-3321-10 FACEPIECE, USS ........................................................1

UOC: Y739 PCOZZ 81361 5-1-3321-20 FACEPIECE, USS ........................................................1

UOC: 7Y3, 73Y10 PCOZZ 81361 5-1-2707-1 FACEPIECE SECOND..................................................1

UOC: Y7310 PCOZZ 81361 5-1-2707-2 FACEPIECE SECOND..................................................1

UOC: 7Y3, 73Y

END OF FIGURE

C-1-1

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION II

Figure C-2. Mask Assembly M40A1

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2


GROUP 01: FACEPIECE ASSEMBLY:FIELD M40A1

FIGURE C-2. FACEPIECE ASSEMBLY

1 PCOZZ 81361 5-1-1081 DISK, VALVE................................................................12 PCOZZ 81361 5-1-1085 DRINK TUBE, INTERNAL .............................................13 PAOZZ 81361 5-1-2796 HARNESS, HEAD.........................................................14 PAOZZ 81361 5-1-1050-10 DEFLECTOR, POST, SUB............................................1

UOC: Y734 PAOZZ 81361 5-1-1050-20 DEFLECTOR, POST, SUB............................................1

UOC: 7Y3, 73Y5 PAOZZ 81361 5-1-1055 DISK, VALVE...............................................................16 PAOZZ 81361 5-1-1054 BODY, VALVE ..............................................................17 PAOZZ 81361 5-1-1086 QUICK DISCONNECT ..................................................18 PAOZZ 81361 5-1-1057 DISK, VALVE................................................................19 PAOZZ 81361 5-1-1009 COVER, OUTLET VALVE.............................................110 PAOZZ 03038 5-1-1059 RING, RETAINING. INST..............................................111 PCOZZ 81361 5-1-1047 DIAPHRAGM, MICROPHONE ......................................112 PCOZZ 81361 5-1-1060 GASKET .......................................................................1

END OF FIGURE

C-2-1

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION II

Figure C-3. Chemical Biological Mask: Combat Vehicle M42A2

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION II


GROUP 00: CHEMICAL BIOLOGICAL MASK:FIELD M42A2

FIGURE C-3. CHEMICAL BIOLOGICAL MASK

1 PAODD 81361 5-1-1001-10 FACEPIECE ASSEMBLY..............................................1UOC: 213

1 PAODD 81361 5-1-1001-20 FACEPIECE ASSEMBLY..............................................1UOC: 21M

1 PAODD 81361 5-1-1001-30 FACEPIECE ASSEMIBLY.............................................1UOC: 21L

2 PAOZZ 81361 5-1-3339 MICROPHONE, DETACHABLE ....................................13 PAOZZ 81361 5-1-1545-20 OUTSERTS, NEUTRAL ................................................14 PAOZZ 81361 5-1-1545-10 OUTSERTS, CLEAR.....................................................15 PAOZZ 81361 5-1-2774 CARRIER ASSY ...........................................................16 PCOZA 81316 5-3-1520 CANISTER, CHEMICAL-B ............................................17 PAOZZ 81349 MILB51170 BAG, WATERPROOFING, C ........................................18 PAOZZ 81361 5-1-1003 FACEFORM PACKAGING............................................19 PAOOO 81361 5-1-1963 HOSE ASSEMBLY........................................................110 PAOOO 81361 5-1-1971 CANISTER CARRIER ASSEMBLY ...............................111 PCOZZ 81361 5-1-2701 HOOD ASSEMBLY .......................................................112 PCOZZ 81361 5-1-3321-10 FACEPIECE, USS ........................................................1

UOC: 21312 PCOZZ 81361 5-1-3321-20 FACEPIECE, USS ........................................................1

UOC: 21M, 21L13 PCOZZ 81361 5-1-2707-1 FACEPIECE SECOND..................................................1

UOC: 21313 PCOZZ 81361 5-1-2707-2 FACEPIECE SECOND..................................................2

UOC: 21M, 21L

C-3-1

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION II

Figure C-4. Chemical Biological Mask: Combat Vehicle M42A2

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION II


GROUP 01: FACEPIECE ASSEMBLY:

FIGURE C-4. FACEPIECE ASSEMBLY

1 PCOZZ 81361 5-1-1081 DISK, VALVE................................................................12 PCOZZ 81361 5-1-1085 DRINK TUBE, INTERNAL .............................................13 PAOZZ 81361 5-1-2796 HARNESS, HEAD.........................................................14 PAOZZ 81361 5-1-1050-10 DEFLECTOR, POST, SUB............................................1

UOC: 2134 PAOZZ 81361 5-1-1050-20 DEFLECTOR, POST, SUB............................................1

UOC: 21M, 21L5 PAOZZ 81361 5-1-1055 DISK, VALVE................................................................16 PAOZZ 81361 5-1-1054 BODY, VALVE ..............................................................17 PAOZZ 81361 5-1-1086 QUICK DISCONNECT ..................................................18 PAOZZ 81361 5-1-1057 DISK, VALVE................................................................19 PAOZZ 81361 5-1-1009 COVER, OUTLET VALVE.............................................110 PAOZZ 03038 5-1-1059 RING, RETAINING, INST..............................................111 PCOZZ 81361 5-1-1047 DIAPHRAGM, MICROPHONE ......................................112 PCOZZ 81361 5-1-1060 GASKET .......................................................................1

END OF FIGURE

C-4-1

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION II

Figure C-5. Canister Carrier Assembly


GROUP 02: CANNISTER CARRIER

FIGURE C-10. CANISTER CARRIER ASSEMBLY

1 PAOZZ 81361 5-1-1960-10 DISCONNECT, ASSY ARM ..........................................1

END OF FIGURE

C-5-1

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION II

Figure C-6. Hose Assembly


GROUP 03: HOSE ASSEMBLY

FIGURE C-11. HOSE ASSEMBLY

1 PCOZZ 81361 5-1-1522 GASKET, CONNECTOR...............................................12 PAOZZ 81361 5-1-1524 COVER, CLAMP...........................................................2

END OF FIGURE

C-6-1

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION III. SPECIAL TOOLS LIST

Not Applicable

C-7-1

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION IV

CROSS-REFERENCE INDEXESNATIONAL STOCK NUMBER INDEX

STOCK NUMBER FIG. ITEM STOCK NUMBER FIG ITEM

4240-00-377-9401 C-1 6 4240-01-413-1540 C-1 10C-3 7 C-3 13

4820-01-226-7005 C-2 6 4240-01-413-1543 C-1 10C-4 6 C-3 13

5330-01-231-3877 C-6 1 5965-01-414-2257 C-3 24240-01-260-8696 C-6 2 4240-01-415-4517 C-1 14240-01-260-8697 C-1 7 C-3 1

C-3 8 4240-01-415-4518 C-1 14240-01-260-8698 C-1 4 C-3 14240-01-260-8699 C-2 9 4240-01-416-0430 C-1 1

C-4 9 C-3 15365-01-260-8700 C-2 10

C-4 105965-01-260-8701 C-2 11

C-4 115330-01-260-8702 C-2 12

C-4 124820-01-260-8703 C-2 1

C-4 14240-01-260-8706 C-1 2

C-3 34240-01-260-8707 C-1 3

C-3 44820-01-260-8709 C-2 8

C-4 84820-01-260-8710 C-2 5

C-4 54240-01-260-8711 C-2 2

C-4 24240-01-267-8161 C-2 4

C-4 44240-01-268-0392 C-2 4

C-4 45965-01-277-8689 C-2 104240-01-361-1319 C-1 5

C-3 64240-01-376-0471 C-2 9

C-3 124240-01-376-1382 C-3 104240-01-376-3152 C-1 8

C-3 114240-01-378-6479 C-3 94240-01-381-1568 C-1 9

C-3 124730-01-391-8461 C-2 7

C-4 74730-01-392-2173 C-5 14240-01-399-3350 C-3 5

I-1

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION IVCROSS-REFERENCE INDEXES

PART NUMBER INDEX

CAGEC PART NUMBER STOCK NUMBER FIG. ITEM

81349 MILB51170 4240-00-377-9401 C-1 6C-3 7

81361 5-1-1001-10 4240-01-415-4517 C-1 1C-3 1

81361 5-1-1001-20 4240-01-415-4518 C-1 1C-3 1

81361 5-1-1001-30 4240-01-416-0430 C-1 1C-3 1

81361 5-1-1003 4240-01-260-8697 C-1 7C-3 8

81361 5-1-1009 4240-01-260-8699 C-2 9C-4 9

81361 5-1-1047 5965-01-260-8701 C-2 11C-4 11

81361 5-1-1050-10 4240-01-267-8161 C-2 4C-4 4

81361 5-1-1050-20 4240-01-268-0392 C-2 4C-4 4

81361 5-1-1054 4820-01-226-7005 C-2 6C-4 6

81361 5-1-1055 4820-01-260-8710 C-2 5C-4 5

81361 5-1-1057 4820-01-260-8709 C-2 8C-4 8

81361 5-1-1059 5365-01-260-8700 C-2 10C-4 10

81361 5-1-1060 5330-01-260-8702 C-2 12C-4 12

81361 5-1-1081 4820-01-260-8703 C-2 1C-4 1

81361 5-1-1085 4240-01-260-8711 C-2 2C-4 2

81361 5-1-1086 4730-01-391-8461 C-2 7C-4 7

81361 5-1-1522 5330-01-231-3877 C-6 181361 5-1-1524 4240-01-260-8696 C-6 281361 5-1-1545-10 4240-01-260-8707 C-1 3

C-3 481361 5-1-1545-20 4240-01-260-8706 C-1 2

C-3 381361 5-1-1960-10 4730-01-392-2173 C-5 181361 5-1-1963 4720-01-378-6479 C-3 981361 5-1-1971 4240-01-376-1382 C-3 1081361 5-1-2701 4240-01-376-3152 C-1 8

C-3 11

I-2

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION IVCROSS-REFERENCE INDEXES

PART NUMBER INDEX

CAGEC PART NUMBER STOCK NUMBER FIG. ITEM81361 5-1-2707-1 4240-01-376-0471 C-1 10

C-3 1281361 5-1-2707-2 4240-01-381-1568 C-1 10

C-3 1281361 5-1-2774 4240-01-399-3350 C-3 581361 5-1-2775 4240-01-260-8698 C-1 481361 D5-2-1661 4240-01-223-7313 C-2 3

C-4 381361 5-1-3321-10 4240-01-413-1540 C-1 9

C-3 1381361 5-1-3321-20 4240-01-413-1543 C-1 9

C-3 1381361 5-1-3339 5965-01-414-2257 C-3 281361 5-3-1520 4240-01-361-1319 C-1 5

C-3 6

I-3

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION IV

CROSS-REFERENCE INDEXESFIGURE AND ITEM NUMBER INDEX

FIG ITEM STOCK NUMBER CAGEC PART NUMBER

C-1 1 4240-01-415-4517 81361 5-1-1001-10C-1 1 4240-01-415-4518 81361 5-1-1001-20C-1 1 4240-01-416-0430 81361 5-1-1001-30C-1 2 4240-01-260-8706 81361 5-1-1545-20C-1 3 4240-01-260-8707 81361 5-1-1545-10C-1 4 4240-01-260-8698 81361 5-1-2775C-1 5 4240-01-361-1319 81361 5-3-1520C-1 6 4240-00-377-9401 81349 MILB51170C-1 7 4240-01-260-8697 81361 5-1-1003C-1 8 4240-00-376-3152 81361 5-1-2701C-1 9 4240-01-376-0471 81361 5-1-1707-1C-1 9 4240-01-381-1568 81361 5-1-2707-2C-1 10 4240-01-413-1540 81361 5-1-3321-10C-1 10 4240-01-413-1543 81361 5-1-3321-20C-2 1 4820-01-260-8703 81361 5-1-1081C-2 2 4240-01-260-8711 81361 5-1-1085C-2 3 81361 5-1-2796C-2 4 4240-01-267-8161 81361 5-1-1050-10C-2 4 4240-01-268-0392 81361 5-1-1050-20C-2 5 4820-01-260-8710 81361 5-1-1055C-2 6 4820-01-226-7005 81361 5-1-1054C-2 7 4730-01-391-8461 81361 5-1-1086C-2 8 4820-01-260-8709 81361 5-1-1057C-2 9 4241-01-260-8699 81361 5-1-1009C-2 10 5365-01-260-8700 03038 5-1-1059C-2 11 5965-01-260-8701 81361 5-1-1047C-2 12 5330-01-260-8702 81361 5-1-1060C-3 1 4240-01-415-4517 81361 5-1-1001-10C-3 1 4240-01-415-4518 81361 5-1-1001-20C-3 1 4240-01-416-0430 81361 5-1-1001-30C-3 2 5965-01-414-2257 81361 5-1-3339C-3 3 4240-01-260-8706 81361 5-1-1545-20C-3 4 4240-01-260-8707 81361 5-1-1545-10C-3 5 4240-01-399-3350 81361 5-1-2774C-3 6 4240-01-361-1319 81361 5-3-1520C-3 7 4240-00-377-9401 81349 MILB51170C-3 8 4240-01-260-8697 81361 5-1-1003C-3 9 4720-01-378-6479 81361 5-1-1963C-3 10 4240-01-376-1382 81361 5-1-1971C-3 11 4240-01-376-3152 81361 5-1-2701C-3 12 4240-01-376-0471 81361 5-1-2707-1C-3 12 4240-01-381-1568 81361 5-1-2707-2C-3 13 4240-01-413-1540 81361 5-1-3321-10C-3 13 4240-01-413-1543 81361 5-1-3321-20

I-4

TM 3-4240-346-20 & PTM 09204A/09205A - 20&P/2

SECTION IV

CROSS-REFERENCE INDEXESFIGURE AND ITEM NUMBER INDEX

FIG ITEM STOCK NUMBER CAGEC PART NUMBERC-4 1 4820-01-260-8703 81361 5-1-1081C-4 2 4240-01-260-8711 81361 5-1-1085C-4 3 81361 5-1-2796C-4 4 4240-01-267-8161 81361 5-1-1050-10C-4 4 4240-01-268-0392 81361 5-1-1050-20C-4 5 4820-01-260-8710 81361 5-1-1055C-4 6 4820-01-226-7005 81361 5-1-1054C-4 7 4730-01-391-8461 81361 5-1-1086C-4 8 4820-01-260-8709 81361 5-1-1057C-4 9 4240-01-260-8699 81361 5-1-1009C-4 10 5365-01-260-8700 81361 5-1-1059C-4 11 5965-01-260-8701 81361 5-1-1047C-4 12 5330-01-260-8702 81361 5-1-1060C-5 1 4730-01-392-2173 81361 5-1-1960-10C-5 1 5330-01-231-3877 81361 5-1-1522C-6 2 4240-01-260-8696 81361 5-1-1524

I-5 (I-6 blank)

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

APPENDIX D

EXPENDABLE AND DURABLE ITEMS LIST

SECTION I. INTRODUCTION

D-1. SCOPE

The expendable/durable supplies and materials list is identical for the M40A1 and the M42A2 masks. This appendix listsexpendable and durable items that you will need to operate and maintain the M42/M42A1/M42A2 Masks. This listing is forinformational purposes only and is not authority to requisition the listed items. These items are authorized to you by CTA50-970, Expendable/Durable Items (except medical, Class V, repair parts, and heraldic items), or CTA 8-100, ArmyMedical Department Expendable/Durable Items.

D-2. EXPLANATION OF COLUMNS.

a. Column 1-Item Number. This number is assigned to the entry in the listing and is referenced in the narrativeinstructions to identify the item.,("Use tubing, item 5, app E").

b. Column 2-Level. This column identifies the lowest level of maintenance that requires the listed item (C-Operator/Crew, O-Unit Maintenance, F- Direct Support Maintenance).

c. Column 3-National Stock Number. This is the National stock number assigned to the item which you can use torequisition it.

d. Column 4-Description. Indicates the item name, description, (CAGEC) and part number. This provides the otherinformation you need to identify the item.

e. Column 5-Unit of Measure (U/M). This code shows the physical measurement or count of an item, such as gallon(GL), each (EA), dozen (DZ), gross (GZ), etc. If the unit of measure differs from the unit of issue, requisition the lowest unitof issue that will satisfy your requirements.

D-1

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

SECTION II. EXPENDABLE AND DURABLE ITEMS LIST

(1)

ITEMNUMBER

(2)

LEVEL

(3)NATIONAL

STOCKNUMBER

(4)

DESCRIPTION

(5)

U/M

1

2

3

4

5

6

7

8

9

10

11

O

C

C

O

O

OO

O

C

O

C

O

O

6515-01-234-6838

7920-00-205-0565

7920-00-461-0037

6665-00-978-5516

6810-00-242-4770

6810-00-255-04716810-00-238-8115

6850-00-592-3283

8305-00-222-2423

8415-00-926-6696

6505-00-655-8366

8010-00-085-0559

6810-00-123-7047

APPLICATOR, DISPOSABLE: plasticor wood, cotton tipped(5L934) 362

BRUSH, DUSTING, LENS(81348) H-B-1654

BRUSH, SCRUB: nylon bristle(81348) H-B- 1490-6-P1

BULB, ASPIRATOR(40912)B-H-5607

CALCIUM HYPOCHLORITE, TECHNICAL:granular: 45 lb. bx. (12 ea 3-3/4 lb. bt.)(81348)OC1146 oz. BT5 lb. BT

CLEANING COMPOUND, OPTICAL LENS(04019) LENSWICK

CLOTH, CHEESECLOTH(81348)CCC-C-440

GLOVES, CHEMICAL AND OIL(81348) ZZ-G-381

ISOPROPYL RUBBING ALCOHOL:bottle, plastic container(56287) PUREPAC

LACQUER: No. 4 black, bushing 4.0 oz(133.4 g) bt(19139)4

N-AMYL ACETATE, REAGENT:clear flammable liquid(81349) MIL-C-51130

EA

EA

EA

EA

LB

OZLB

DZ

YD

PR

PT

OZ

PT

D-2

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

SECTION II. EXPENDABLE AND DURABLE ITEMS LIST

(1)

ITEMNUMBER

(2)

LEVEL

(3)NATIONAL

STOCKNUMBER

(4)

DESCRIPTION

(5)

U/M

12

13

14

15

16

17

18

19

20

C

O

O

C

O

O

O

O

O

7240-01-094-4305

5120-00-228-0730

5110-00-293-3444

8520-00-228-0598

6665-00-928-5731

8115-00-726-0673

8115-00-222-3715

8135-00-116-1443

7510-00-266-5016

PAIL, UTILITY: plastic, snap-on lid,5.00 gal.(58536) A-A-332

SCREWDRIVER, JEWELER(81348) GGG-S-1808 type 1

SHEARS, STRAIGHT TRIMMERS: 6 in.(81348) GGG-S40278

SOAP, TOILET: nonmedicated,liquid, type 1(81348) P-S-624

TUBE, SMOKE(40912) BH5645

BOX SHIPPING(81348) PPP-B-640

CRATE, SHIPPING(81336) D1152-1

CUSHIONING MATERIAL(81349) MIL-P-26514

TAPE, PRESSURE SENSITIVE: 2" wide(81348) PPP-T-60

EA

EA

PR

CL

EA

EA

EA

RO

RO

D-3 (D-4 blank)

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

INDEXSUBJECT PAGE

AAdjusting Mask Assembly at Initial Fitting .................................................................................................................. 2-19

Adjusting Mask Assembly ................................................................................................................................... 2-21Checking Mask Assembly for Fit ......................................................................................................................... 2-22Putting on Mask Assembly .................................................................................................................................. 2-20

Airflow Deflector, Inlet Valve Disk, and Valve Body.................................................................................................... 2-59Installation .......................................................................................................................................................... 2-61Removal ............................................................................................................................................................. 2-59

CChecking Drinking System for Proper Function.......................................................................................................... 2-28Checking the Mask Assembly for Proper Function ..................................................................................................... 2-23

Testing Mask Assembly with a-Amyl Acetate....................................................................................................... 2-24Testing Mask Assembly with M41 PATS (M40A1) ............................................................................................... 2-23Testing Mask Assembly with M41 PATS (M42A2) ............................................................................................... 2-23

Checking for Leaks.................................................................................................................................................... 2-28Clamp Cover ............................................................................................................................................................. 2-75

Installation .......................................................................................................................................................... 2-75Removal ............................................................................................................................................................. 2-75

Cleaning and Sanitizing............................................................................................................................................. 2-77Cleaning Carrier (M40A1) ................................................................................................................................... 2-80Cleaning Carrier (M42A2) .................................................................................................................................. 2-90Cleaning Mask Assembly (M40A1)..................................................................................................................... 2-77Cleaning Mask Assembly (M42A2)...................................................................................................................... 2-85Sanitizing Mask Assembly (M40A1) .................................................................................................................... 2-81Sanitizing Mask Assembly (M42A2 ) ................................................................................................................... 2-91

Common Tools and Equipment ................................................................................................................................. 2-3Corrosion Prevention and Control (CPC) .................................................................................................................. 1-1

DDestruction of Army Materiel to Prevent Enemy Use.................................................................................................. 1-1Differences Between Models .................................................................................................................................... 1-10

E(EIR), Reporting Equipment Improvement Recommendations.................................................................................... 1-1Equipment Characteristics, Capabilities, and Features............................................................................................... 1-2Equipment Data ........................................................................................................................................................ 1-11Equipment/User Fitting Instructions ........................................................................................................................... 2-19Expendable Durable Supplies and Materials List .......................................................................................................D-1

FFigure and Item Number Index ................................................................................................................................ I-4

HHead Harness ........................................................................................................................................................... 2-57


How to Use This Manual ........................................................................................................................................... iii

Index 1

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

INDEXSUBJECT PAGE

I

Identifying an Individual's Mask ................................................................................................................................. 2-18Index (Chapter 2) ...................................................................................................................................................... 2-1Internal Drink Tube.................................................................................................................................................... 2-54

Checking for Fit.................................................................................................................................................. 2-55Installation .......................................................................................................................................................... 2-54Removal ............................................................................................................................................................. 2-54

Internal Drink Tube Nipple......................................................................................................................................... 2-66Verification.......................................................................................................................................................... 2-66Installation .......................................................................................................................................................... 2-67Removal ............................................................................................................................................................. 2-67

LLeft/Right Filter Canister/Hose Assembly Conversion ................................................................................................ 2-45

MMaintenance Allocation Chart (MAC) (M40A1)...........................................................................................................B-3Maintenance Allocation Chart (MAC) (M42A2)...........................................................................................................B-4Maintenance Forms, Records, and Reports ............................................................................................................... 1-1Maintenance Procedures........................................................................................................................................... 2-53

NNational Stock Number Index ................................................................................................................................... I-1Nosecup Valve Disks................................................................................................................................................. 2-58


OOptical Insert Kit, Plastic............................................................................................................................................ 2-68

Adjustment.......................................................................................................................................................... 2-72Installation .......................................................................................................................................................... 2-70Removal ............................................................................................................................................................. 2-69

Optical Insert Kit, Wire............................................................................................................................................... 2-68Installation .......................................................................................................................................................... 2-68Removal ............................................................................................................................................................. 2-68

Outlet Valve Cover and Outlet Valve Disk.................................................................................................................. 2-63Installation .......................................................................................................................................................... 2-64Removal ............................................................................................................................................................. 2-63

PPort Gasket ............................................................................................................................................................... 2-76


Preparation for Storage or Shipment ......................................................................................................................... 2-95Preventative Maintenance Checks and Services (PMCS) .......................................................................................... 2-39Principles of Operation .............................................................................................................................................. 1-12Putting on Mask Assembly ........................................................................................................................................ 2-20

QQuick Disconnect Coupling, External Drink Tube....................................................................................................... 2-56


Index 2

TM 3-4240-346-20 & PTM 09204A/09205A-20 & P/2

INDEX

SUBJECT PAGE

R

References................................................................................................................................................................A-1Repair Parts and Special Tools List (RPSTL).............................................................................................................C-1Repair Parts, Special Tools, TMDE and Support Equipment ...................................................................................... 2-3Reporting Equipment Improvement Recommendations (EIR) .................................................................................... 1-1Reporting Errors and Recommending Improvements................................................................................................. i

SSanitizing M40A1 ...................................................................................................................................................... 2-81Sanitizing M42A2 ...................................................................................................................................................... 2-91Service Upon Receipt................................................................................................................................................ 2-3Service Upon Receipt of Materiel .............................................................................................................................. 2-3Side Voicemitter, Voicemitter Retainer, and Gasket................................................................................................... 2-65


Storage or Shipment, Preparation for ........................................................................................................................ 2-95Supplies and Materials List, Expendable/Durable ......................................................................................................D-1Part Number Index .................................................................................................................................................... I-2Symptom Index ......................................................................................................................................................... 2-29

TTable of Contents...................................................................................................................................................... iiTools and Equipment, Common ................................................................................................................................ 2-3Tool and Test Equipment Requirements.................................................................................................................... 2-3Troubleshooting ........................................................................................................................................................ 2-29

UUnit Maintenance Repair Parts and Special Tools List ...............................................................................................C-1Unit Maintenance Instructions (See Individual Procedure) ......................................................................................... 2-53

VVoicemitter, Side, Voicemitter Retainer and Gasket................................................................................................... 2-65


Index 3 (Index 4 blank)

By Order of the Secretary of the Army:

DENNIS J. REIMEROfficial: General United States Army

Chief of Staff

JOEL B. HUDSONAdministrative Assistant to the

Secretary of the Army05239

DISTRIBUTION:

To be distributed in accordance with the Initial Distribution Number (IDN) 280848 , requirements for TM3-4240-346-20&P

M. K. HAYDENColonel, USMCDirector, Program SupportMarine Corps Systems Command

pcn 182 092041 00 - dragon's den · * this manual supersedes the m40a1 part of tm...

Documents