peco lighting incentives

7/29/2019 PECO Lighting Incentives

1/13

L01 $1.50L02 $6.00L03 $6.00

L04 $30.00L05 $55.00

L06 $7.50L07 $7.50L08 $7.50L09 $12.50

L10 $7.00L11 $5.00L12 $1.00

L13 $9.00L14 $1.00

L15 $5.00L16 $5.00L17 $4.00L18 $3.00

L19 $15.00

L20 $25.00L21 $25.00L22 $25.00L23 $25.00

L24 $15.00L25 $20.00L26 $30.00L27 $50.00

L28 $30.00

L29 $4.00

L30 $0.10L31 $0.12

L32 $30.00

# of Fix tures Watts/Fix ture# of

FixturesWatts/Fixture

Total

Watts

Reduced

IncentiveCalculated

Incentive

Total Interior Lighting Incentives:

Rev 09/12/11Page 9

3-ft Lamp

Lamp

LampLamp

4-ft Lamp

Daylight Sensor Controls

FixtureBi-Level Stairwell/Hall/Garage Fixtures withIntegrated Sensors

8-ft Lamp Only (T8 to RW T8)

3-ft T12 to T8

LED Lamp/Fixture, 18W or Less Lamp/Fixture

Single-sided Exit Signs Replacing CFL

Pulse Start or Ceramic, 201W - 350WPulse Start or Ceramic, 101W - 200WPulse Start or Ceramic, 100W or Less

FixtureFixture

Double-sided Exit Signs Replacing CFL Signs

4-foot Lamp4-ft Reduced Watt Lamp Only (T8 to RW T8)

8-ft Lamp

4-ft Lamp and Ballast (T12 to HP or RW T8)

Lighting

Measure Code

I NTERI OR LI GHTI NG I NCENTI VES WORKSHEET

Interior Compact Fluorescent Lamps, Screw-in (Replacing Incandescent)

Interior Hardwired Compact Fluorescent Fixtures (Replacing Incandescent)

Interior Permanent Lamp Removal (Pre-Notification Application Is Required, See Measure Specification for Further Details)

Interior High Performance or Reduced Wattage 4-ft T8

Interior Reduced Wattage 8-ft T8

Interior Standard Linear Fluorescent Retrofit (T12 to T8)

Interior Metal Halide

Interior LED Lamp/Fixture

Interior LED, T-1 or Electroluminescent Exit Signs

Equipment Type Unit # of Units Incentive CalculatedIncentive

CFL - Screw-in (30W or Less)CFL - Screw-in (31W - 115W)

4-foot Lamp

2-ft T12 to T8

Fixture

Single-sided Exit Signs Replacing Incandescent

4-ft T12 to T8 - Includes U lamps8-ft T12 to 4-ft 2-Lamp T8

$0.35/Watts

Reduced

L33

Lamp

Lamp

LampLamp

Lamp removed

8-ft 1-Lamp T12 to 4-ft 2-Lamp HP T8

8-ft Lamp and Ballast (T12 to RW T8)

29W or Less

CFL - Downlight, Dimmable or 3-way

30W or Greater

Lamp removed2-ft Lamp

LampLampLamp

FixtureFixture

Lamp removedLamp removed

Pre and Post Fixture descriptions

(Fixture Codes from TRM Table of Standard

Wattages)

Description

Occupancy Sensors

Fixture

Interior Induction Lighting

Interior Cold Cathode (Replacing Incandescent)

Incentive

Signs

Cold Cathode

LampIntegrated Ballast Ceramic Metal Halide Lamp

Interior Controls (Attach list of controlled fixtures, quantities, and wattages)

$0.00

New Fixture Quantity:

Lamp

Interior Induction Fixture

Sub Total: $0.00

Conversion to New Interior T8/T5 Fluorescent Fixtures with Electronic Ballast (Pre-Notification Application is Required)

New fixtures are capped at $200 per fixture. This measure is not to be combined with any of the measures listed above.

Watts ControlledWatts Controlled

Pre Post

Double-sided Exit Signs Replacing Incandescent SignsSigns


2/13

L34 $15.00

L35 $48.00L36 $52.00L37 $48.00L38 $52.00L39 $48.00L40 $52.00L41 $48.00L42 $52.00L43 $48.00L44 $52.00L45 $48.00L46 $52.00

L47 $50.00

L48 $50.00

L49 $45.00L50 $65.00L51 $120.00

L52 $150.00

L53 $30.00



Total

Watts

Reduced

IncentiveCalculated

Incentive

Total Exterior Lighting Incentives:Rev 09/12/11

Page 10

LED traffic lights - Walk/Don't Walk - 12"

LED traffic lights - Green 8" (ARROW)LED traffic lights - Green 12" (ARROW)

Metal Halide or High Pressure Sodium Fixturereplacing Incandescent or Mercury Vapor Fixture

LED traffic lights - Yellow 12" (ARROW) Lamp

LED traffic lights - Yellow 12" (ROUND)

Lamp

LampLamp

LED traffic lights - Red 8" (ROUND)LED traffic lights - Red 12" (ROUND)

LampLamp

LED traffic lights - Yellow 8" (ARROW)

Lamp

LED traffic lights - Walk/Don't Walk - 9" Lamp

Streetlights and Exterior Fixtures

Exterior Bi-Level Fixtures

Conversion to New Exterior T8/T5 Fluorescent Fixtures with Electronic Ballast (Pre-Notification Application is Required)


Bi-Level Stairwell/Hall/Garage Fixtures withintegrated sensors

Fixture

Pulse Start or Ceramic Metal Halides replacing'Standard' Probe-Start HIDLED or Induction replacing 175W or Less Fixture

Fixture

LED or Induction replacing 176W - 250W Fixture Fixture

Fixture

LED traffic lights - Green 8" (ROUND)LampLED traffic lights - Green 12" (ROUND)

LED traffic lights - Yellow 8" (ROUND) Lamp

LED Traffic and Pedestrian LightsLamp

Lighting

Measure CodeEquipment Type

EXTERI OR LI GHTI NG I NCENTI VES WORKSHEET

Lamp

Lamp

L54

Post

LED or Induction replacing 251W - 400W Fixture

$0.00

$0.00Capped

Sub Total:New Fixture Quantity:

Bi-Level Fixture

Fixture

$0.30/Watts

Reduced

Description


(Fixture Codes from TRM Table of Standard

Wattages)

Fixture

IncentivePre

Fixture

Screw-in CFLs > 31W

Incentive Unit # of Units

Exterior Compact Fluorescent Lamps, Screw-in

Incentive Calculated


3/13

L55 $75.00L56 $100.00L57 $150.00L58 $20.00

L59 $100.00

L60 $45.00L61 $65.00L62 $120.00L63 $15.00

L64 $50.00

L65 $180.00



Total

Watts

Reduced

IncentiveCalculated

Incentive

Total Garage Lighting Incentives:

Rev 09/12/11Page 11

Parking Garage Application (24-Hour Operation)

Lighting

Measure Code

Fixture

Fixture

Fixture

Incentive # of UnitsUnit

Fixture

$0.00

FixtureFixture

New Fixture Quantity:Capped

Sub Total:

Pre Post

$0.00

Fixture

Conversion to New Interior Parking Garage T8/T5 Fluorescent Fixtures with Electronic Ballast (Pre-Notification Application is Required)


L66


(Use fixture Codes from TRM Table of Standard

Wattages)

Fixture

Metal Halides (Pulse Start or Ceramic)350W - 400W

Bi-Level Wall Pack Fixture

$0.35/Watts

Reduced

Interior Parking Garage Lighting Bi-Level Control with Override


Screw-in CFLs > 31W

LED or Induction replacing 175W or Less Fixture


Lamp

Parking Garage Application (Nights/12-Hour Operation)

Metal Halides (Pulse Start or Ceramic)350W - 400W

LED or Induction replacing 176W - 250W FixtureLED or Induction replacing 175W or Less Fixture

Fixture

Screw-in CFLs > 31W

Fixture


Incentive CalculatedEquipment Type

GARAGE LI GHTI NG I NCENTI VES W ORKSHEET


4/13

Rev 09/12/11Page 12

LI GHTI NG SPECI FI CATI ONS

All lighting projects are expected to comply with the Illuminating Engineering Society of North America

(IESNA) recommended lighting levels or the local code.

The Pennsylvania Public Utilities Commission requires that projects with savings greater than 20 kWcomplete a detailed lighting inventory with pre- and post-light fixture codes, wattages, and site-specific

estimates of operating hours. The worksheet must be submitted in an Excel-readable electronic format.An Excel version of the worksheet is available at www.peco.com/SmartIdeas.

LightingMeasure

CodeSpecification

L01

Interior Compact Fluorescent Lamps, Screw-In (Replacing Incandescent):CFL Screw-in (30W or Less)Screw-in CFLs must replace incandescent existing lamps, and be ENERGY STAR rated lamps ormeet ENERGY STAR criteria.

L02

Interior Compact Fluorescent Lamps, Screw-In (Replacing Incandescent):CFL Screw-in (31W 115W)High wattage CFLs must replace existing incandescent lamps. The lamp must have a minimumluminous efficacy of 65 lumens per watt (LPW).

L03

Interior Compact Fluorescent Lamps, Screw-In (Replacing Incandescent):CFL - Downlight, Dimmable or 3-wayMust replace existing incandescent lamps, metal halide or induction lamps, or other non-CFL withSpecialty CFLs such as PAR, 3-way, dimmable. The lamps must qualify under ENERGY STARcriteria, if applicable for the type of lamp.

L04L05

Interior Hardwired Compact Fluorescent Fixtures (Replacing Incandescent)For interior hardwired CFL fixtures, only complete new fixtures or modular hardwired retrofits withhardwired electronic ballasts qualify. The CFL ballast must be programmed start or programmed rapidstart with a power factor (PF) 0.90 and a total harmonic distortion (THD) 20%. Screw-in CFLs arenot eligible for this incentive.

L06L07L08L09

Interior Permanent Lamp Removal (Pre-Notification Application is Required)Incentives are offered for the permanent removal of existing fluorescent lamps. Permanent lampremoval is the net reduction in the quantity of lamps. Customers are responsible for determining

whether or not to use reflectors in combination with lamp removal in order to maintain adequatelighting levels. Lighting levels are required to meet the Illuminating Engineering Society of NorthAmerica (IESNA) recommended light levels for the occupancy and use. U tube lamps are eligible forthis measure and will be considered as a 4-foot lamp. Unused lamps, lamp holders, and ballasts mustbe permanently removed from the fixture and disposed of in accordance with local regulations. Thismeasure is applicable when retrofitting from T12 lamps to T8 lamps or reconfiguring a T8 fixture toreduce the number of lamps. Removing lamps from a T12 fixture that is not being retrofitted with T8lamps are not eligible for this incentive. A Pre-Notification Application is required for lamp removalprojects in order for PECO to conduct a pre-retrofit inspection.


5/13


Rev 09/12/11Page 13

Table 2.Reduced Wattage 4-Foot Lamps and BallastsPerformance Characteristics for Lamps1

Mean System Efficacy 90 MLPWColor Rendering Index (CRI) 80

Minimum Initial Lamp Lumens 2585 Lumens for 28 W 2400 Lumens for 25 W

Lamp Life2 18,000 hrs at three hours per start

Lumen Maintenance -or-Minimum Mean Lumens3

94% or 2430 Lumens for 28 W 2256 Lumens for 25 W

Performance Characteristics for 28 and 25W Ballasts

Ballast Frequency 20 to 33 kHz or 40 kHzPower Factor 0.90

Total Harmonic Distortion 20%Performance Characteristics for Ballasts4, 28W systems

Ballast Efficacy Factor (BEF) Instant-Start Ballast (BEF):BEF = [BF x 100] / Ballast Input Watts Lamps All Ballast Factor Ranges

Based on: 1 3.52(1) Type of ballast 2 1.76

(2) No. of lamps driven by ballast 3 1.16(3) Ballast Factor 4 0.88

Performance Characteristics for Ballasts4, 25 W systemsBallast Efficacy Factor (BEF) Instant-Start Ballast (BEF)

BEF = [BF x 100] / Ballast Input Watts Lamps All Ballast Factor RangesBased on: 1 3.95

(1) Type of ballast 2 1.98(2) No. of lamps driven by ballast 3 1.32

(3) Ballast Factor 4 0.99

1 Lamps 4500 K and/or 24000 hours have a system efficacy specified 88 MLPW. Minimum initial and mean lumen levels are specified as follows: for 28W lamps, limits are 2600/2340. For 25 W lamps, limits are 2300/2185.2

Life rating is based on an instant Start Ballast tested in accordance with ANSI protocols. When used for Program Start Ballast, life may be increased

depending upon the operating hours per start.

3 Mean lumens measures at 7,200 hours.

4 Multi-Voltage Ballasts must meet or exceed the listed Ballast Efficacy Factor when operated on at least one of the intended operating voltages

Table 1. High Performance 4-foot T-8 Lamps and BallastsPerformance Characteristics for Systems

Mean System Efficacy 90 Mean Lumens per Watt (MLPW) for Instant Start Ballasts

88 MLPW for Programmed Rapid Start BallastsPerformance Characteristics for Lamps

Color Rendering Index (CRI) 80Minimum Initial Lamp Lumens 3100 Lumens*

Lamp Life 24,000 HoursLumen Maintenance or Minimum

Mean Lumens 94 % or 2900 Mean Lumens

Performance Characteristics for Ballasts

Ballast Efficacy Factor (BEF)BEF=(BFx100)/Ballast Input Watts

Instant Start Ballast (BEF)

Lamps Low BF 0.85Norm

0.85 < BF 1.0High BF 1.01

1 > 3.08 > 3.11 NA2 > 1.60 > 1.58 > 1.553 1.04 1.05 1.044 0.79 0.80 0.77

Programmed Rapid Start Ballast (BEF)1 2.84 2.84 NA2 1.48 1.47 1.513 0.97 1.00 1.004 0.76 0.75 0.75

Ballast Frequency 20 to 33 kHz or 40 kHzPower Factor 0.90

Total Harmonic Distortion 20%

*For lamp with color temperatures 4500K, 2950 minimum initial lamp lumens are allowed.


6/13


Rev 09/12/11Page 14

LightingMeasure

CodeSpecification

L10L11

Interior High Performance or Reduced Wattage 4-ft T8:4-ft Lamps and Ballasts (T12 to HP or RW T8)8-ft 1-Lamp T12 to 4-ft 2-Lamp HP T8This measure consists of replacing existing T12 lamps and magnetic ballasts with high performanceT8 lamps or reduced wattage (28W or 25W) T8 lamps and electronic ballasts. This measure is basedon the Consortium for Energy Efficiency (CEE) high performance T8 specification (www.cee1.org) andis summarized in Table 1 on the previous page. A list of qualified lamps and ballasts can be found at:http://www.cee1.org/com/com-lt/com-lt-main.php3. Both the lamp and ballast must meet thespecification in order to qualify for an incentive. Incentives for this measure are calculated per numberof lamps installed. A manufacturers specification sheet for the specific lamp and ballast installed mustaccompany the application.

L12

Interior High Performance or Reduced Wattage 4-ft T8:4-ft Reduced Watt Lamp Only (T8 to RW T8)Incentives are offered for replacing 32 Watt T8 lamps with reduced wattage T8 lamps when anelectronic ballast is already present. The lamps must be reduced wattage and meet the Consortiumfor Energy Efficiency (CEE) specification (www.cee1.org). Qualified products can be found at:http://www.cee1.org/com/com-lt/com-lt-main.php3. The nominal wattage of the new lamp must be

28W ( 2585 Lumens) or 25W ( 2400 Lumens) to qualify. The mean system efficacy must be 90MLPW, CRI 80, and lumen maintenance at 94 percent. A manufacturers specification sheet mustaccompany the application.

L13L14

Interior Reduced Wattage 8-ft T8Incentives are offered for replacing T12 lamps and magnetic ballasts with reduced wattage 8-foot T8lamps and electronic ballasts. Eight-foot lamps must have a minimum MLPW of 90 and must have anominal wattage of less than or equal to 57 W. A manufacturers specification sheet mustaccompany the application. Retrofits involving eight-foot lamps with a nominal wattage of greaterthan 57 W will be considered on a custom basis.

L15L16

L17L18

Interior Standard Linear Fluorescent Retrofit (T12 to T8)Incentives are offered for replacing existing T12 lamps and magnetic ballasts with T8 lamps andelectronic ballasts. The electronic ballast must be high f requency (20 kHz), UL listed, andwarranted against defects for a minimum of 5 years. Ballasts must have a power factor (PF) 0.90.Ballasts for 4-foot lamps must have total harmonic discharge (THD) 20 percent at full power

output. For 2 and 3-foot lamps, ballasts must have THD 32 percent at full light output. Amanufacturer's specification sheet for the specific lamp and ballast installed must accompany theapplication.Incentive is also available for 4-foot U-tube T8 lamps and CEE qualified ballasts replacing existingU-tube T12 lamps and magnetic ballasts.

L19Interior LED Lamp/FixtureSee LED specification page.


7/13


Rev 09/12/11Page 15

LightingMeasure

CodeSpecification

L20L21L22L23

Interior LED, T-1, or Electroluminescent Exit Signs

Incentives are offered for high-efficiency single- and double-sided exit signs; enter on line withappropriate existing lamp type (incandescent or CFL). New LED lamps must replace or retrofit anexisting incandescent or fluorescent exit sign. Electroluminescent, T1, and light-emitting diode (LED)exit signs are eligible under this category. Non-electrified and remote exit signs are not eligible. Allnew exit signs or retrofit exit signs must be UL or ETL listed, have a minimum lifetime of 10 years,and have an input wattage 5 Watts per face or be ENERGY STAR qualified.

L24

Interior Metal Halide:Integrated Ballast Ceramic Metal Halide LampQualifying lamps are 25 watts or less integrated ballast ceramic metal halide PAR lamps with a ratedlife of 10,500 hours or greater. This measure must replace an incandescent lamp.

L25L26L27

Interior Metal Halide:Pulse Start or CeramicIncentives are offered for retrofits with either pulse start metal halide or ceramic metal halide fixturesthat replace existing standard probe-start high intensity discharge lamps and ballasts. Totalreplacement fixture wattage must be at least 30% lower than existing fixture wattage to ensure energysavings. Retrofit kits must be used on existing mercury vapor, standard metal halide or high pressuresodium fixtures only. No new fixtures are allowed.

L28

Interior Induction LightingIncentives are offered for interior induction lighting. Only new, hard-wired induction fixtures qualify.New fixtures must replace, one for one, existing incandescent, mercury vapor, T12/High Outputfluorescent, T12/Very High Output fluorescent, Standard Metal Halide, or High Pressure Sodiumfixtures in interior installations. The new fixtures must not exceed the maximum Wattage listed in thetable below for each range of lamp Wattage being replaced. Total replacement fixture wattage must beat least 30% lower than existing fixture wattage to ensure energy savings.

L29Interior Cold CathodeAll Cold Cathode Fluorescent Lamps (CCFLs) must replace incandescent lamps that are between 10and 40 Watts. Product must be rated for at least 18,000 average life hours.

L30

Interior Controls:Occupancy SensorsPassive infrared, ultrasonic detectors and fixture-integrated sensors or sensors with a combinationsensor are eligible. All sensors must be hard-wired and control interior lighting fixtures. The incentive isper Watt controlled. An inventory of the controlled fixtures and their wattages must be provided foreach sensor. Wattages for this measure must come from the Lighting TRM Wattage Table.


8/13


Rev 09/12/11Page 16

LightingMeasure

CodeSpecification

L31

Interior Controls:Daylight Sensor ControlsIncentives are offered for daylight sensor controls in spaces with suitable available ambient light for atleast part of the day. Light may be through skylights, clerestories, windows or light tubes. Thecontrols can be on/off, stepped or continuous (dimming). The on/off controller should turn off artificiallighting when the interior illuminance meets the desired indoor lighting level. The stepped controllergenerally dims the artificial lighting 50% when the interior illuminance levels reach 50% of the desiredlighting levels. Continuous or dimming controllers dim artificial lighting proportional to the availableambient light. All types of daylight sensor controls are required to be commissioned in order to ensureproper sensor calibration and energy savings. Incentives are per watt controlled.

L32

Interior Controls:Bi-Level Stairwell/Hall/Garage Fixtures with Integrated SensorsIncentives are offered for hardwired two-lamp T8 fluorescent fixtures with electronic ballasts andmanufacturer integrated occupancy sensors used in areas where lighting operates 24 hours a day(such as stairwells, halls, and garages). Fixtures with manual override capabilities are not eligible.During occupied periods, the fixture should operate at full light output. The fixture must operate at awattage that is at least 30% lower than the full output lighting wattage level. This measure is not alsoeligible for the occupancy sensor incentive.

L33

Conversion to New Interior T8 /T5 Fluorescent Fixtures with Electronic Ballast (Pre-NotificationApplication is Required)This measure consists of replacing one or more existing fixtures with new fixtures containing T8 or T5fixtures with electronic ballasts. The electronic ballast must be high frequency ( 20 kHz), NRTL listed,and warranted against defects for five years. Ballasts must have a power factor (PF) 0.90. Ballastsfor 4-foot lamps must have total harmonic distortion (THD) 20% at full light output. For 2-foot and 3-foot lamps, ballasts must have THD 32% at full light output. High output T5/T8 lamps also qualify forthis rebate. This incentive may be used in high bay and low bay fluorescent applications.Specifications of the new fixtures, lamps and ballasts, must accompany the final application. Aninventory of the pre- and post-retrofit fixtures and their wattages must be provided. Wattages for thismeasure must come from the Lighting TRM Wattage Table. Incentives are only available for newfixtures. Retrofit kits are not considered to be new fixtures.

L34

Exterior Compact Fluorescent Lamps, Screw-in (> 31W)This incentive applies to screw-in lamps and applies only if an incandescent or high-intensity discharge

(HID) lamp is being replaced. Total replacement fixture wattage must be at least 30% lower thanexisting fixture wattage to ensure energy savings.

L35 L46

LED Traffic and Pedestrian LightsIncentives are offered for LED traffic lights on a per-signal basis (including arrows) that replace orretrofit an existing incandescent traffic signal. Incentives are not available for spare lights. Lights mustbe hard-wired, with the exception of pedestrian hand signals.


9/13


Rev 09/12/11Page 17

LightingMeasure

CodeSpecification

L47

Streetlights and Exterior Fixtures:Metal Halide or High Pressure Sodium Fixture replacing Incandescent or Mercury Vapor FixtureIncentives are offered to replace incandescent or mercury vapor fixtures with high pressure sodium ormetal halide fixtures. Total replacement fixture wattage must be at least 30% lower than existing fixturewattage to ensure energy savings.

L48

Streetlights and Exterior Fixtures:Pulse Start or Ceramic Metal Halides replacing Standard Probe-Start HIDIncentives are offered for retrofits with either pulse start metal halide or ceramic metal halide fixturesthat replace existing standard probe-start high intensity discharge lamps and ballasts. Totalreplacement wattage must be 20% lower than existing wattage to ensure energy savings. Retrofit kitsmust be used on existing mercury vapor, standard metal halide or high pressure sodium fixtures only.

L49L50

L51

Streetlights and Exterior Fixtures:LED or Induction replacing 175W / 176W - 250W / 251W - 400W FixtureIncentives are offered for replacing existing exterior high intensity discharge or incandescent outdoorlight fixtures with LED or Induction fixtures. Existing fixtures must operate > 3,833 hours per year (>10.5 hours per day). Total replacement fixture wattage must be at least 30% lower than existing fixture

wattage to ensure energy savings. LED fixtures must have a minimum efficacy of 35 lumens per watt.Eligible applications include pole-mounted, or canopy lighting and wall-packs. This incentive can becombined with incentives for exterior/garage bi-level control. Incentive is per fixture.

L52

Exterior Bi-Level Fixtures:Bi-Level FixtureIncentives are available for exterior bi-level fixtures. The new fixture must be integrated withoccupancy sensor that allows the light to switch between high and low levels based on the presence ofvehicle or pedestrian traffic. Switching between high and low light levels based on occupancymaintains sufficient light for security and way-finding while maximizing energy savings. The new f ixturemust be pulse start metal halide, induction, or LED and have lower nominal wattage than the existingfixture. The reduced wattage lamp must operate at a wattage that is at least 30% lower than the fulloutput lighting wattage level. No additional incentives for this measure can be claimed when applyingfor this incentive. Incentive is per fixture.

L53

Exterior Bi-Level Fixtures:

Bi-Level Stairwell/Hall/Garage Fixtures with Integrated SensorsIncentives are offered for hardwired two-lamp T8 fluorescent fixtures with electronic ballasts andmanufacturer integrated occupancy sensors used in areas where lighting operates 24 hours a day(such as stairwells, halls, and garages). Fixtures with manual override capabilities are not eligible.During occupied periods, the fixture should operate at full light output. The fixture must operate at awattage that is at least 30% lower than the full output lighting wattage level. This measure is not alsoeligible for the occupancy sensor incentive.


10/13


Rev 09/12/11Page 18

LightingMeasure

CodeSpecification

L54

Conversion to New Exterior T8/T5 Fluorescent Fixtures with Electronic Ballast

(Pre-Notification Application is Required)Incentives are offered for replacing one or more existing fixtures with new fixtures containing T8 or T5lamps and electronic ballasts. The electronic ballast must be high frequency ( 20 kHz), UL listed, andwarranted against defects for 5 years. Ballasts must have a power factor (PF) 0.90. Ballasts for 4-foot lamps must have total harmonic distortion (THD) 20% at full light output. For 2- and 3-footlamps, ballasts must have THD 32% at full light output. High output T5/T8 lamps also qualify for thisrebate.

Incentives for this measure are calculated based on the reduction in connected watts. A Pre-Notification Application is required for this measure in order for PECO to conduct a pre-retrofitinspection. Specifications of the new fixtures, lamps and ballasts, must accompany the finalapplication. Incentives are only available for new fixtures and the maximum incentive amount is $200per fixture. An inventory of the pre- and post-retrofit fixtures and their wattages must be provided.Wattages for this measure must come from the Lighting TRM Wattage Table. Retrofit kits are notconsidered to be new fixtures.

Note: PCB ballasts and lamps are hazardous materials and must be disposed of properly by theApplicant.

L55L56L57

Parking Garage Application (24-hour Operation):LED or Induction replacing 175W / 176W - 250W / 251W - 400W FixtureIncentives are available in garage applications for replacing existing high intensity discharge fixtureswith LED or Induction fixtures. Fixture replacement must result in at least a 30% power reduction. LEDfixtures should have a minimum efficacy of 35 lumens per watt.

L58

Parking Garage Application (24-hour Operation):Screw-in CFLs > 31WThis incentive applies to screw-in lamps and applies only if an incandescent or high-intensity discharge(HID) lamp is being replaced. Lamp/ballast combination must have an efficacy 40 lumens per Watt(LPW). Total replacement fixture wattage must be at least 30% lower than existing fixture wattage toensure energy savings.

L59

Parking Garage Application (24-hour Operation):Metal Halide Fixtures (Pulse Start or Ceramic) 350W 400W

Incentives are offered for retrofits with either pulse start metal halide or ceramic metal halide fixturesthat replace existing standard probe-start high intensity discharge lamps and ballasts. Totalreplacement wattage must be lower than existing wattage to ensure energy savings. This measure issubject to possible pre-inspection. Retrofit kits must be used on existing mercury vapor, standardmetal halide or high pressure sodium fixtures only. No new fixtures are allowed. Total replacementfixture wattage must be at least 30% lower than existing fixture wattage to ensure energy savings.


11/13


Rev 09/12/11Page 19

LightingMeasure

CodeSpecification

L60L61L62

Parking Garage Application (12-hour Operation):

LED or Induction replacing 175W / 176W - 250W / 251W - 400W FixtureIncentives are available in garage applications for replacing existing high intensity discharge fixtureswith LED or Induction fixtures. Fixture replacement must result in at least a 30% power reduction. LEDfixtures should have a minimum efficacy of 35 lumens per watt.

L63

Parking Garage Application (12-hour Operation):Screw-in CFLs > 31WThis incentive applies to screw-in lamps and applies only if an incandescent or high-intensity discharge(HID) lamp is being replaced. Lamp/ballast combination must have an efficacy 40 lumens per Watt(LPW). Total replacement fixture wattage must be at least 30% lower than existing fixture wattage toensure energy savings.

L64

Parking Garage Application (12-hour Operation):Metal Halide Fixtures (Pulse Start or Ceramic) 350W 400W Incentives are offered for retrofits with either pulse start metal halide or ceramic metal halide fixturesthat replace existing standard probe-start high intensity discharge lamps and ballasts. Totalreplacement wattage must be lower than existing wattage to ensure energy savings. This measure issubject to possible pre-inspection. Retrofit kits must be used on existing mercury vapor, standardmetal halide or high pressure sodium fixtures only. No new fixtures are allowed. Total replacementfixture wattage must be at least 30% lower than existing fixture wattage to ensure energy savings.

L65

Interior Parking Garage Lighting Bi-Level Control with Override:Bi-Level Wall Pack FixtureIncentives are offered for bi-level fixtures in interior parking garage applications. These fixtures areintended for use in areas where high lighting levels are required when occupied, but are actuallyunoccupied for the majority of the time. These fixtures employ a motion sensor-type lighting switch toprovide lower levels of light while unoccupied, and full illumination while occupied. Incentive is perfixture. The reduced wattage lamp must operate at a wattage that is at least 30% lower than the fulloutput lighting wattage level. This measure cannot be combined with interior occupancy sensors forgarage applications. No additional incentives for this measure can be claimed when applying for thisincentive. This measure applies to fixtures that operate at 24 hours.


12/13


Rev 09/12/11Page 20

LightingMeasure

CodeSpecification

L66

Conversion to New Interior Parking Garage T8/T5 Fluorescent Fixtures with Electronic Ballast(Pre-Notification Application is Required)Incentives are offered for replacing one or more existing fixtures with new fixtures containing T8 or T5lamps and electronic ballasts. The electronic ballast must be high frequency ( 20 kHz), UL listed, andwarranted against defects for 5 years. Ballasts must have a power factor (PF) 0.90. Ballasts for 4-foot lamps must have total harmonic distortion (THD) 20% at full light output. For 2- and 3-footlamps, ballasts must have THD 32% at full light output. High output T5/T8 lamps also qualify for thisrebate.

Incentives for this measure are calculated based on the reduction in connected watts. A Pre-Notification Application is required for this measure in order for PECO to conduct a pre-retrofitinspection. Specifications of the new fixtures, lamps and ballasts, must accompany the finalapplication. Incentives are only available for new fixtures and the maximum incentive amount is $200per fixture. Retrofit kits are not considered to be new fixtures.

Note: PCB ballasts and lamps are hazardous materials and must be disposed of properly by theApplicant.


13/13

Rev 09/12/11Page 21

LED LI GHTI NG SPECI FI CATI ONS

Option A:The integral lamp or fixture must appear on the Energy Star Qualified Products List or theDesign Lights Consortium Qualified Products List.

Energy Star Qualified Fixture Product List:

http://www.energystar.gov/index.cfm?fuseaction=ssl.display_products_com_excel

Energy Star Qualified Integral LED lamps:

http://www.energystar.gov/index.cfm?fuseaction=iledl.display_products_excel

Energy Star Qualified Commercial LED Lighting:

http://www.energystar.gov/index.cfm?fuseaction=ssl.display_products_com_excel

Design Lights Qualified Product List:

http://www.designlights.org/documents/NEEPDLCQPL_Public.pdf

Option B:

Please submit the following documents:

1. Manufacturers product information sheet2. LED package/fixture specification sheet3. Manufacturer should provide methodology for calculation and justification of product

lifetime estimates

4. A complete IESNA LM-79-08 test report(s) for product testing conducted at approved labsfor each product. The report should include the following information

a. Photometric measurements (i.e. light output and efficacy)

b. Colorimetry report (i.e. CCT and CRI)

c. Electrical measurements (i.e.) input voltage, current, power, power factor, etc.)5. Lumen Maintenance report (select one of the following two options and submit all the

corresponding documents.

a. Option 1: Compliance through component performance (for the corresponding

LED package)

i. IESNA LM-80 test report

ii. In-Situ Temperature Measurements Test (ISTMT) report.iii. Schematic/photograph from LED package manufacturer that shows the

specified temperature measurement point (TMP)

b. Option 2: Compliance through luminaire performance

i. IESNA LM-79-08 report at 0 hours (same file as item #3 above)

ii. IESNA LM-79-08 report at 6000 hours after continuous operation in the

appropriate ANSI/UL 1598 environment (use ANSI/UL 1574 for track

lighting systems).

LEDs that do not appear on the Qualified Products lists of either Energy or Design Lights

Consortium will be evaluated using the minimum performance criteria in the appropriate product

category from either Energy Star or Design Lights Consortium for the follow variables:

Light output in lumens

Luminaire efficacy (lm/W)

Color rendering index (CRI)

Correlated color temperature (CCT)

LED lumen maintenance at 6000 hrs

Manufacturers estimated lifetime for L70 (70% lumen maintenance at end of useful life)

peco lighting incentives

Documents