ps ppt by saran
TRANSCRIPT
![Page 1: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/1.jpg)
YOUNG STARSINSULATORSPresented by
k.NagasaravananKarthick rajaD.s.mukesh
![Page 2: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/2.jpg)
CONTENTS. What is insulators Types of insulatorsCauses of failure of insulatorsString efficiencyPotential distribution over suspension insulator
string One mark q&a 12 mark q&aReference
![Page 3: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/3.jpg)
WHAT IS INSULATORSThe overhead lines conductors should be
supported on the poles or towers in such way that current from conductors do not flow to earth through support.
![Page 4: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/4.jpg)
Properties of insulators.High mechanical strength in order to
withstand conductor load , wind load.High electrical resistance of insulator
material in order to avoid leakage current to earth.
High relative permittivity of insulator material in order that di-electric strength is high.
The insulator materials should be non-porous , free from impurities and cracks otherwise the permittivity will be lower.
High ratio of puncture strength to flashover.
![Page 5: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/5.jpg)
TYPES OF INSULATORS.Pin type insulatorsSuspension type insulatorsStrain insulatorsShackle insulators
![Page 6: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/6.jpg)
PIN TYPE INSULATORS.A Pin insulator consists of non- conducting
material such as glass, porcelain , wood ,polymer and plastic.
As the name suggest , the pin type insulator is secured to the cross-arm pole .
There is a groove on the upper end of the insulator for housing the conductor.
The conductor passes through this groove and this bound by the annealed wire of the same material as the conductors.
![Page 7: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/7.jpg)
Pin insulator are used for transmission and distribution of electric power at voltage up to 33kv
Beyond operating voltage of 33 kv , the pin type insulator become too bulky and uneconomical
![Page 8: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/8.jpg)
DIAGRAM FOR PIN INSULATOR
![Page 9: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/9.jpg)
CAUSES OF INSULATOR FAILURE.Insulators are required to withstand both
mechanical and electrical stresses.The ladder type is primarily due to line voltage and
may cause the breakdown of the insulator. The electrical break down of the insulator can
occurs either by puncture.In flash over , an arc occurs between the line
conductor and I hsulator pin and the discharge jumps.
In case of flash over, the insulator will continue to act in its proper capacity unless extreme produced by arc destroys the insulator.
safety factor of insulator = puncture strength flash – over voltage
![Page 10: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/10.jpg)
SUSPENSION INSULATOR.The cost of pin type insulator increases rapidly as
the working voltage is increased.This type of insulator is not economical beyond
33kv.They consist of a number of proceleain discs
connected in series by metal links in the form of a strings.
The conductor is suspended at the bottom end of the string while the other end of the strings is secured to the cross-arm of the tower.
The working voltage is 66kv,then six discs in series will be provided on the string.
![Page 11: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/11.jpg)
DIAGRAM FOR SUSPENSION INSULATOR.
![Page 12: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/12.jpg)
ADVANTAGESSuspension type insulators are cheaper than
pin type insulators for voltages beyond 33kv.Each unit or disc of suspension type insulator
is designed for low voltage , usually 11kv.depending upon the working voltage , the desired number of discs can be connected in series.
If any one disc is damaged , the whole string does not become useless because the damaged disc can be replaced by the sound one.
![Page 13: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/13.jpg)
Cont….The suspension arrangement provides greater
flexibility to the line . The connection at the cross arm is such that insulator string is free to swing in any direction and can take up the position where mechanical stresses are minimum.
In case of increased demand on the transmission line, it is found more satisfactory to supply the greater demand by raising the line voltage than to provide another set of conductor.
The suspension type insulators are generally used with steel towers. As the conductors below the earthed cross-arm of the tower , therefore , this arrangement provides partial protection from lightning.
![Page 14: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/14.jpg)
STRAIN INSULATOR When there is a dead end of the line or there is corner or
sharp curve, the line is subjected to greater tension.In order to relieve the line of excessive tension, strain
insulators are used.For low voltage lines (< 11 kV), shackle insulators are used
as strain insulators. However, for high voltage transmission lines, strain insulator
consists of an assembly of suspension insulators as shown in Figure.
The discs of strain insulators are used in the vertical plane.When the tension in lines is exceedingly high, at long river
spans, two or more strings are used in parallel.
![Page 15: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/15.jpg)
DIAGRAM FOR STRAIN INSULATOR
![Page 16: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/16.jpg)
SHACKLE INSULATORS. In early days, the shackle insulators were
used as strain insulators.But now a days, they are frequently used
for low voltage distribution lines.Such insulators can be used either in a
horizontal position or in a vertical position.
They can be directly fixed to the pole with a bolt or to the cross arm.
![Page 17: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/17.jpg)
DIAGRAM FOR SHACKLE INSULATOR
![Page 18: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/18.jpg)
Potential distribution over suspension insulator stringThe voltage impressed on a string of suspension
insulators does not distribute it self unformally across the individual discs due to the presence of shunt capacitance.
The disc nearest to the conductor has maximum voltage across it.as we move towards the closs arm , the voltage across each disc goes on decreasing.
The unit nearest to the conductor is under maximum electrical stress and it likely to the punctured . Therefore , means must be provided to equalise the potential across each unit.
If the voltage impressed across the string were d.c.., then voltage across each unit would be the same. It is because insulator capacitances are ineffective for d.c.
![Page 19: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/19.jpg)
DIAGRAM
![Page 20: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/20.jpg)
DERIVATIONApplying Kirchhoff’s current law to node A, we get,I2 = I1 + i1or V2ω C* = V1ω C + V1ω C1or V2ω C = V1ω C + V1ω K C
∴ V2 = V1 (1 + K) ...(i)Applying Kirchhoff’s current law to node B, we get,I3 = I2 + i2or V3 ω C = V2ω C + (V1 + V2) ω C1†
![Page 21: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/21.jpg)
or V3 ω C = V2ω C + (V1 + V2) ω K Cor V3 = V2 + (V1 + V2)K= KV1 + V2 (1 + K)= KV1 + V1 (1 + K)2 [ V2 = V1 (1 + K)]= V1 [K + (1 + K)2]
∴ V3 = V1[1 + 3K + K2] ...(ii)Voltage between conductor and earth (i.e., tower) isV = V1 + V2 + V3= V1 + V1(1 + K) + V1 (1 + 3K + K2)= V1 (3 + 4K + K2)
![Page 22: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/22.jpg)
∴ V = V1(1 + K) (3 + K) ...(iii)From expressions (i), (ii) and (iii), we get,
V1/1=V2/1+K=V3/1+3K+ K 2 =V/(1+K)(3+K)
...(iv)∴Voltage across top unit, V1 = V/(1 + K)(3 + K)
![Page 23: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/23.jpg)
Voltage across second unit from top, V2 = V1 (1 + K)Voltage across third unit from top, V3 = V1 (1 + 3K + K2)%age String efficiency =Voltage across string×100/n ×Voltage across disc nearest to conductor= V/3 × V3 ×100
![Page 24: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/24.jpg)
METHODS OF IMPROVING STRING EFFICIENCY1. By using longer cross arms : The value of string efficiency depends up on the value of
K.ratio of shunt capacitance to mutual capacitance. The lesser the value of k , the greater is the string
efficiency and more uniform is the voltage distribution.2. By grading the insulators: In this method , insulators of different dimensions are
so chosen that each has a different capacitance. Since voltage is inversely proportional to capacitance.3. By using a guard ring: The potential across each unit in a string can be
equalised by using a guard ring which is a metal ring electrically connected to the conductor and surrounding the bottom insulator.
![Page 25: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/25.jpg)
DIAGRAM FOR METHODS OF STRING EFFICIENCY
![Page 26: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/26.jpg)
ONE MARKS :1. Define insulator 2. Name types of insulator.3. Give any four reason for causes failure of
insulator.4. Define string efficiency
![Page 27: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/27.jpg)
12 MARKS1. Explain the various methods of testing of
insulators2. Bring out the reasons for the failure of
Insulator (6)3. Explain any two methods to improve the
string efficiency (6)
![Page 28: Ps ppt by saran](https://reader034.vdocument.in/reader034/viewer/2022050614/58a0e1721a28abeb378b6d39/html5/thumbnails/28.jpg)
THANK YOU