R/C QUAD COPTER INSTRUCTION FOR USE

The materials and specification mentioned in this instruction manual are for reference only. Please refer to SYMA website for additional information.

Please read carefully this instruction before using the quad copter

Safety Instructions1. Please keep the quadcopter and the box away from small children.2. Please keep a safe distance from high speed rotating propellers to avoid injury.3. First time users should be gentle with the throttle to avoid crashing the quadcopter or any potential injuries.4. When finished flying, please turn off first the remote controller then the quadcopter.5. Please keep the charging battery away from fire and humidity.6. Do not fly the quadcopter near pets, young children, elderly and disabled people.7. Non rechargeable batteries are not to be charged; Different types of batteries or new and used batteries are not to be mixed; Batteries are to be inserted with correct polarity; Exhausted batteries are to be removed from the product. The supply terminals are not to be short circuited8. When not in use, please turn off the power of controller and quadcopter. When the quadcopter is not in use for a long period of time, remove the batteries from remote controller.

Step 1: Install the fully charged battery into the copter.

Step 2: The copter will start flashing red (fast). Place the copter on a flat surface.

Step 3: Switch on the remote control.

Step 4: Push the left throttle stick up and down. The copter should be ready. If it is not responding, start over from step 1.

Note: If the quadcopter was not set up properly (not place on a flat surface), start over from step 1.

Low power protection

When the quadcopter’s battery is low, the system will cut-off the power to avoid excessive discharge. This will reduce any damage to the battery.

Note: if the blades of the copter are stuck, the copter will automatically switch off to protect the motors.

2. Charging the battery: remove the battery from the quadcopter and plug it into the specific plug in the USB cable. Then plug the USB cable into a computer or a USB charger. The red light indicates the battery is charging. It will switch off when the battery is fully charged.

Note: Disconnect the USB plug before turning off the computer.

Once charged, insert the battery as shown on the picture, and follow steps in the “ready to fly” paragraph.

Charge time: 65-75 minutes—Fly time about 8 minutes!The quadcopter contains a built-in Li-Po battery, please pay attention to the following matters:- Keep the battery away from fire and heating sources. It could damage the battery or cause it to explode.- Keep the quadcopter and the battery away from water.- Only charge the quadcopter with the provided adapter.- Do not remove or dismantle the built-in battery.- Do not leave unattended when charging.

Battery Installation & ChargingBattery Installation in the remote controller

Different types of batteries or new and used batteries are not to be mixed;Batteries are to be inserted with correct polarity;Exhausted batteries are to be removed from the product;The supply terminals are not to be short circuited.

1. Use a crosshead screw driver to remove the controller battery cover. Insert 4 batteries (size AA, 1.5V) observing the correct polarity indicated in the compartment. Replace the battery cover and secure the screw.

3D Eversion guideAfter familiar with basic action, let’s try breath taking eversion! First fly up to 3m height, hold button C on top right corner and push rudder(any direction), quadcopter will finish the 3 daction, and direction 360˚continuous eversion.

Sideway flight fine tuning.01

Forward/backward fine tuning.02

Turn right/left fine tuning.03

Throttle fine tuning.04

Throttle power bar.05

Forward indicator.06

Sideway (left) indicator.07

Backward indicator.08

Sideway (left) indicator.09

Backward indicator.10

Turn right indicator.11

High speed mode (H displayed).12

Low speed mode (L displayed).13

RC battery charge.14

Mode 1 (default mode) Throttle and turning left/right on left command, sideway on right command.

15

Mode 2 Throttle and sideway on left command, turning left/right on right command.

16

Signal bar.17

Mini quadcopter indicator.18

Button C: the 360˚ eversion button.19

All the cursors for fine tuning are by default centred.

Change speed mode when pushing button B.

How to use your remote control:

To switch modes, turn off the remote control then turn it on while pushing simultaneously button A right. The LCD display should indicate Mode 1 or Mode 2.

Troubleshooting

No reaction from the quadcopter

No reaction from the quadcopter when in flight

1. Not enough power for the quadcopter.2. Not enough power for the controller.3. The channel is different from quadcopter and the controller.4. The gyro of the quadcopter can’t find out the right point.

Have the same frequency remote controltransmitter.

Spare partsAll the spare parts below can be bought from local distributor.

1. Charge the quadcopter battery2. Install new batteries in controller3. Make sure the same channel is used for the quadcopter and the controller.4. Move the quadcopter onto a flat surface, and then turn it on. Then turn on the controller

Change frequency or use the quadcopter out of the range of other RC quadcopters.

Step 4: Push the left throttle stick up and down. The copter should be ready. If it is not responding, start over from step 1.