Assembly & Installation Instructions for:

Packer™ Pro Hitch-Mount Cargo Carrier

PN: 59530

TM

A B

C D E

F G H

I J K

BASKET HALF B (X1)

FRONT BRACKET (X1) REAR BRACKET (X1) SHANK & 2” ADAPTER (X1)

CENTER PLATE (X1) HEX BOLT 1/4-20 (X12) FLAT WASHER 1/4 (X24)

LOCK NUT 1/4-20 (X12) CARRIAGE BOLT 3/8-16 (X2) FLAT WASHER 3/8 (X2)

Assembly & Installation Instructions for

Packer™ Pro Hitch-Mount Cargo Carrier

L M N LOCK NUT 3/8-16 (X2)

O P Q WRENCH (X1) L-WRENCH (X1)

BASKET HALF A (X1)

ANTI-RATTLE PIN & CLIP

(X1)

LOCK WASHER (X1)

ADHESIVE REFLECTOR

STRIP (X2)

Assembly & Installation Instructions for

Packer™ Pro Hitch-Mount Cargo Carrier

ALL ROLA PRODUCTS MUST BE INSTALLED PROPERLY AND SECURELY

ATTACHED TO YOUR VEHICLE. IMPROPER USE OR ATTACHMENT COULD

LEAD TO AN AUTOMOBILE ACCIDENT AND/OR BODILY HARM OR DEATH

TO YOU OR OTHERS. AS THE OWNER OF THIS PRODUCT, YOU ARE RE-

SPONSIBLE FOR PROPER INSTALLATION TO YOUR VEHICLE, CHECKING

THE ATTACHMENTS PRIOR TO USE, PRACTICING SAFE AND PROPER USE

OF THE PRODUCT, AND PERIODICALLY INSPECTING THE PRODUCT FOR

FIT, WEAR, AND DAMAGE. THEREFORE, IT IS CRITICAL THAT YOU READ

AND UNDERSTAND ALL OF THE INSTRUCTIONS, WARNINGS, CAUTIONS,

AND RECOMMENDATIONS PRIOR TO INSTALLATION OR USE.

WHAT YOU’LL NEED FOR ASSEMBLY

3

Lay Basket Half A and Basket

Half B side-by-side as shown

B A

2

Line up the holes on Front

Bracket (C) with the holes on the

front of Basket Half A and Basket

Half B.

1

Add Flat Washer (H) to Hex Bolt

(G) and feed the bolt through the

holes in the front bracket and

Basket Halves.

6

Add a second Washer (H) and a

Lock Nut ( I ).

5

Tighten the Hex Bolt and Lock Nut

until snug.

4

Repeat steps 3-5 in all six places

for Front Bracket (C). 1

2

3 4

5

6

5

9

7

Insert Shank & Adapter (E)

through Rear Bracket (D) as

shown (with adapter end still

exposed).

Line up the holes on Rear Bracket

(D) with the holes on the rear of

Basket Half A and Basket Half B.

8

Repeat steps 3-6 in all six places

for Rear Bracket (D).

1

2

3 4

5

6

On the underside of the basket,

add Flat Washer (K) and Lock Nut

(L) to each Carriage Bolt (J) and

tighten.

Lay Center Plate (F) across the

center of the basket floor, lining up

the notches with the holes in the

shank.

Feed Carriage Bolt (J) through the

notches in Center Plate (F) and

through the holes in the shank.

10

11

12

Add Lock Washer (N) to Anti-

Rattle Pin (M) as shown.

13

14

15

Add the Adhesive Reflector Strips

(Q) to the front corners of the

cargo carrier for increased

nighttime visibility.

Install the Cargo Carrier on your

vehicle by sliding the Shank of the

carrier into the receiver tube on

your vehicle as shown.

Fasten Clip to the end of the

Anti-Rattle Pin as shown.

Using Wrench (O), tighten the

Anti-Rattle pin until snug.

16

17

18

Line the holes in the adapter/

shank up with the holes in the

receiver then insert the Anti-Rattle

Pin (M).

19

USING WITH

1-1/4” RECEIVER?

Using L-Wrench (M), remove the

screw on the side of the Adapter,

then remove the adapter from the

shank.

WARNING

INCORRECT CORRECT

ALWAYS center/distribute load evenly in cargo carrier. ALWAYS securely fasten load to cargo carrier using bungees or a cargo net. NEVER transport people, animals, or flammable liquids in cargo carrier.

CAUTION

If the load or cargo carrier blocks or impairs visibility of the taillightsor turn signals, use optional light kit (part #6504).

If license plate is blocked by load or cargo carrier, relocate using existing holeslocated on the carrier.

If the cargo carrier or the contents being transported is in line with the exhaustoutlet, an exhaust tip must be used to redirect the exhaust flow away from thecargo platform or contents.

Do not lubricate threads. Bolt failure may occur due to over tightening.

Check security of load, fasteners, pin, and clip often during travel.

Severe bumps can damage your towing vehicle, hitch, and cargo carrier.Drive slowly on rough roads.

Stop and make a thorough inspection if your cargo carrier strikes the road.Correct any problems before resuming travel.

Do not carry loads wider than your vehicle.

The cargo carrier load rating is the LOWEST of the following:• Cargo carrier rating (500 lb with 2” Shank; 300 lb with 1-1/4” Shank)• Hitch tongue weight rating• Vehicle manufacturer tongue weight rating

Service Kits & Optional Accessories

Available for your

Packer™ Pro Hitch-Mount Cargo Carrier

Part No.: 59916

Aluminum 1-1/4” to 2” Adapter

Part No.: 59915

Anti-Rattle Pin & Clip

Part No.: 59917

Wrench

Part No.: 6504

Incandescent Light Kit

Part No.: 7330

Cargo Net

Part No.: 59200

Flat Strap Cargo Net