salice 110° 3/8 rabbeted face frame hinge...
TRANSCRIPT
1
Salice 110° 3/8" Rabbeted Face Frame Hinge Instructions
Vertical Positioning of HingesAlthough Euro-style concealed hinges allow for some vertical adjustment, the mounting plate must line up with the hinge arm if the two are to snap together and provide the maximum possible adjustment range. The easiest way to accomplish this is to mark aligning horizontal centerlines on both the door and the face frame. You need to consider the amount of the door’s overlay or inset when calculating the centerline positions for the door.
1. For the top hinge, measure down from the top of the cabinet opening to the desired mounting location (typically 2"-3") and use a combination square to mark the horizontal centerline on the back of the face frame. (For the bottom hinge, measure up from the bottom of the cabinet opening.) Note: Be sure your hinge positions will provide adequate clearance for any pullouts.
2. To determine the centerline location on the door, start with the distance you measured in Step 1 and add the amount the door will overlap at that edge.
3. Use the values calculated for the top and bottom hinge locations in Step 2 and mark the horizontal centerlines on the back of the door. Compare the distance between the lines on the face frame with the distance between the lines on the door to verify.
Installing Hinges 1. Refer to the Door Diagram to mark drilling locations for the hinge cup holes and mounting screw holes on the door. Note that you measure from the edge of the rabbet to locate the center point for the cup hole.
2. Using a 35mm Forstner bit, drill a hole 9mm deep for the hinge cup, taking care to keep the bit as square as possible to the door. Note: For fast, easy and accurate location and drilling of hinge cup holes, we recommend using the JIG IT Deluxe Concealed Hinge Drilling System (53420, sold separately) along with a Rockler 35mm Long-Shank Forstner Bit (10117, sold separately). For those using a drill press, a dedicated JIG IT setup block is available (59029, sold separately).
3. Drill pilot holes for the screws, taking care not to drill all the way through the door. 4. Position the hinge cup in the hole and use the included screws to secure in place.
5. Repeat Steps 2-4 at other hinge location(s).
Installing Mounting Plates1. Refer to the Face Frame Diagram to mark drilling locations for the hinge plates on the back of the face frame.
2. Drill pilot holes for the mounting screws, taking care not to drill all the way through. Note: For fast, easy and accurate location and drilling of mounting plate pilot holes, we recommend using the JIG IT Hinge Plate Template for 3/8" Lipped Door Hinges (50908, sold separately) along with a Rockler/Insty-Drive #6 Self-Centering Bit (68991, sold separately).
3. Use the included screws to secure the mounting plates onto the face frame. 4. Mount the doors by clipping the hinge arms onto the mounting plates.
Check Rockler.com for updates. If you have further questions, pleasecontact our Technical Support Department at 1-800-260-9663 or [email protected]
24964
Hinge Finish Tab Cup Diameter
Cup Depth
Minimum Door Thickness
Maximum Door Thickness Adjustments Gap Clip-on
MountingMinimum Reveal
Salice 110° 3/8" Rabbet Nickel 11mm 35mm 9mm 12.7mm (.5") 25mm (.98") 3-way cam .7mm Yes 1.5mm
2 Distributed by Rockler Companies, Inc. ©2016 Rockler Woodworking and Hardware
24964Rev 09/16
54
11
28.5
Back of Face Frame
All measurements are in millimeters.
Face Frame Diagram
Turning this screw clockwise adjusts the door down; counterclockwise, up.
Turning this screw clockwise adjusts the door inward; counterclockwise, outward.
Height Adjustment Depth Adjustment Lateral AdjustmentTurning this screw clockwise adjusts the door to the right; counterclockwise, to the left.
9.5
45
OPTIONAL ACCESSORIES
JIG IT® Deluxe Concealed Hinge Drilling Jig 53420
JIG IT® 3/8" Lipped Door Hinge Jig 50908
JIG IT® 11mm Hinge Cup Drill Press Drilling Jig 59029
Lipped edge
TabCenter Mark
Centerline
Cup Depth Diagram
35
Door
Cabinet
Reveal
Gap and Reveal
Gap
9.5
Door Diagram
19
Face Frame
9
3/8" x 3/8" Rabbet