sargent catalog cuts
TRANSCRIPT
2 1-800-727-5477 • www.sargentlock.com
351 Series Powerglide® Door CloserDoor Control
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
Backcheck valve• At approximately 70° of the open cycle,
the Backcheck Valve begins to slow thedoor's motion
• Prevents the door from slamming into the door's stop
• Valve is used to control the intensity ofthe Backcheck
• Note: A Positive stop is required;Backcheck cannot be used as a stop
Closer Spring Adjustment• Not Shown in Door Closer Cycle Diagram• Effects the entire cycle of the door
closer movement• Used to size closer for application
requirements • Determines the amount of force with
which the door closes and the amount offorce required to open the door
• Adjustable to compensate for door sizeand draft conditions
ANSI Standards
ARM TYPE ARM TYPE
O CO2011 PF9 CO2101
P9 CO2021 P10 CO2021
H CO2051 PS/CPS CO2021
PH9 CO2061 CPSH/PSH CO2061
F CO2091
All are certified ANSI types includingoptions PT4 A, B, D, E, F, G, H
Latching speed valve• Controls the speed of the door during
the final 8" of door swing• The force the door closes with is
controlled by the closer spring• Note: This adjustment is critical for
door latching
Delayed action valve (Optional)• Holds the door in the open position
momentarily • 20 second minimum hold open delay• The feature is available for all
applications and arms• Beneficial when moving carts or objects
through door opening or ADA applications
Door Closer Cycle
Closing speed valve• Controls how fast the door closes to
approximately 8" from the closed position,along with the closer spring
How to Select the Proper Closer
Things to Consider 1. Size and Weight of DoorThe 351 Door Closers is non-sized so thatclosing force can be adjusted in the fieldto accommodate various door sizes andweights.
2. Interior ApplicationThe standard application is the mostefficient in terms of power and control.
3. Exterior ApplicationThe top jamb, corner bracket or parallelarm application should be used. Exteriordoors require greater closing forcesbecause of draft conditions. Always placethe closers out of the weather.
4. Degree of OpeningProper arm and position on the door ismost important to permit the door toopen far enough to allow adequatetraffic flow.
5. FunctionClosers are available with hold-open,positive stop or fusible link hold-openarms.
6. Special Condition Consult factory when special hinges,overhead holders or other specializedhardware is used.
OpeningCycle
4 1-800-727-5477 • www.sargentlock.com
351 Series Powerglide® Door CloserStandard Application
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
Adjustable Closing Force• Interior doors to 5'0" wide
• Exterior doors to 4'0" wide
• Shipped factory preset for 3'0" door
• Factory pre-sized upon request
351 Standard Application DoorOpening Range (Range based on Mounting Position)
• O- Standard Arm: 120° - 180°
• H- Hold Open Arm: 90° - 160°
• F- Fusible Link Hold Open Arm: 75°–135°
351 Standard Application for:• Interior Doors Opening In or Out
• Exterior Doors Opening In
• Maximum Reveal 7/16"
• Non-hand universal body
351-0 Standard Application
The standard application of the 351 door closer is the most commonand the most desirable. The closer mounts on the hinge (pull) side ofdoor (except when the W Corner Bracket is used). Note: This applicationis not recommended on exterior doors (the closer is not protected fromweather). The cover projection normally limits the door opening to amaximum of 160°.
Wall Clearance Requirement
2-3/16" MIN SPACE(56mm)
Door in Closed Position
Cover Projection normally limitsdoor opening to 160°
Door in Open Position
O ARM SHOWN
7/8"
(22mm)
3/8"(95mm)
3-7/8" (58mm)
2-3/16"(55mm)
13" (330mm)
VARIES4-1/2" - 7-1/2"
(114mm - 191mm)
6-5/8"
(168mm)
Arm Leverage Adjustment
Closers using “O” or “F” arms have the provision to increase closing power by 15% by adjustingfoot pivot
51-800-727-5477 • www.sargentlock.com
Powerglide® Door CloserArms and Accessoriesfor Standard Application351 Series
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
OLC - Standard Arm for Low Ceiling• Forged Steel
Main Arm• Non-handed• Must be used
when the distancebetween the top of door to ceiling isless than 1-1/4" (32mm)
• Permits 120° door opening withstandard mounting
Order as 25-OLC x finish for arm only Includes: 63-2549 - Main arm and link assembly
63-2216 - Foot assembly63-3684 - Screw pack
O8 - Mortise Foot Arm• Forged Steel
Main Arm• Non-handed• Permits 120°
door opening• Commonly used with bull nose framesOrder as 25-O8 x finish for arm only Includes: 63-2607 - Main arm and link assembly
63-2273 - Foot assembly63-2391 & 63-3684 - Screw packs
H - Hold Open Arm• Forged Steel
Main Arm• Non-handed• Hand is changed
by inverting the foot assembly
• Friction type holder easilyadjusted by a wrench
• Permits 180° door opening• Holds open from 80° to 180°Order as 25-H x finish for arm onlyIncludes: 63-2229 - Main arm
61-2303 - Foot assembly63-3684 - Screw pack
F - Fusible Link Hold Open Arm• Forged Steel
Main Arm • Handed same
as door• Friction type
holder easily adjusted by a wrench• Holds open from 80° to 140°• 160° F Link Standard• Specify 125°F Link when requiredOrder as 25-F x hand x finish for arm only Includes: 63-2240 - Left hand main arm
63-2241 - Right hand main arm 63-2468 - Foot assembly63-3684 - Screw pack
H8 - Mortise Foot Hold Open Arm• Forged Steel
Main Arm• Handed same
as door• Friction type
holder easilyadjusted by a wrench
• Holds open from 80° to 180°Order 25 R-H8 for right hand and 25 L-H8 for left hand xfinish for arm only Includes: 63-2289 - Left hand foot assembly
63-2290 - Right hand foot assembly63-2229 - Main Arm and Link Assembly63-2391 & 63-3684 - Screw packs
O - Standard Arm• Forged Steel
Main Arm• Non-handed• Permits 120° door
opening with standard mounting
• Permits 180° door opening with alternatemounting or corner bracket
Order as 25-O x finish for arm onlyIncludes: 63-2607 - Main arm
63-2216 - Foot assembly63-3684 - Screw pack
UO Package
• Universal armpackage providesbrackets and arms to installcloser in standardtop jamb orparallel applications
• Order closer as 351-UO x finish
• 351-UO not availablewith (MC) metal cover or plated finishes
Screw packs63-3684 & 63-2391
125-P9
UH Package• Universal hold
open arm package provides brackets and arms to install closer in top jamb, standard or parallel applications
• Order closer as 351-UH x finish
• 351-UH not available with (MC) metal cover or plated finishes
Screw packs63-3684
125-PH9
F8 - Mortise Foot Fusible LinkHold Open Arm
• Forged Steel Main Arm
• Handed same as door
• Friction typeholder easily adjusted by a wrench
• Permits 140° door opening• Holds open to 140°• 160° F Link Standard• Specify 125° F Link when requiredOrder as 25-F x hand x finish for arm only Includes: 63-2240 - Left hand main arm assembly
63-2241 - Right hand main arm assembly61-2273 - Foot assembly63-3684 - Screw packs
351L - LCN retro plateDesigned to replace an LCN 4040 closerbody with a SARGENT 351 without drillingnew holes in door (NOTE: New mountingholes required for arm bracket only) Order as: 351L x finish
7/16" Maximum Reveal Depth
CeilingOLC - Low Ceiling Application Arm forCeiling to Doors Clearance 1-1/4"– 1-1/2"Door Top Rail Requirement• 4-1/4" min. rail (108mm)• 351 closer can be mounted on top rails
2-3/8" through 4-1/4" using a 351-A mounting plate
1-1/4"–1-1/2"
9" (229mm)
6" (152 mm)
351-A MOUNTING PLATE
2-3/8" MIN. TOP RAIL(60mm)
6 1-800-727-5477 • www.sargentlock.com
351 Series Powerglide® Door CloserTop Jamb Application
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
351-AMOUNTING PLATE
1-7/16”(37mm) 1-3/4" MIN. (44mm)
3-15/16"(100mm)
1-7/16"(37mm)
LOW CEILING CONDITION
351-BMOUNTING PLATE
1-15/16" MIN.
6"(152mm)
9"(229mm)
6"(152mm)
9"(229mm)
351 Top Jamb Mounting Plates
Minimum Door Top Rail Requiredto Mount Closer Foot• 2" (51mm) minimum
• Rail height used will vary depending on type and make of auxiliary holder
Adjustable Closing Force• Interior doors to 5'0" wide
• Exterior doors to 4'0" wide
• Shipped factory preset for 3'0" door
• Factory pre-sized upon request
351-0 Top Jamb Mounting Position
Minimum Frame Face Required• 1-3/4" minimum required for 351A plate
and 1-15/16" minimum required 351Bplate for both single and doublerabbeted frames
Top Jamb applications - The 351 closer is mounted on the frame faceabove the door. The foot is mounted on the push side of door. Thisapplication is for use on exterior doors opening out to protect thecloser from the weather.
OZ ARM SHOWN
Reveal Depth
Top JambApplication
Frame
• Permits closers to be mounted for specialapplications when overhead auxiliarydoor holders are used or in low ceilingapplications
• Plates are painted or plated steel tomatch closer
• Plates are non-handed
• Order as 351-A or B x finish
13"(330mm)
3-7/8" (98mm)
1-1/4"(32mm)
Varies 3-3/8" to 6-5/8"
351 Typical Reveal Top JambApplicationsFor reveals up to 2" (51mm) maximum
• O Arm - Max. Door Opening: 180°
• H Arm - Hold Open Range: 80°-180°
• F Arm - Fusible Link Hold Open Arm Hold Open Range: 80°-130°
351 Deep Reveal Top JambApplicationsFor reveals from 2-1/8" (54mm) to 5" (127mm)• OZ Arm - Max. Door Opening: 140°• HZ Arm - Hold Open Range: 80°-140°• FZ Arm - Fusible Link Hold Open Arm
Hold Open Range: 80°-130°
351 Extra Deep Reveal Top JambApplicationsFor reveals from 5-1/8" (130mm) to 8" (230mm)• OZA Arm - Max. Door Opening: 140°• HZA Arm - Hold Open Range: 80°-130°• FZA Arm - Fusible Link Hold Open Arm
Hold Open Range: 80°-130°
Narrow Reveal
FZA - Fusible Link Hold Open Armfor Extra Deep Reveal
• Forged Steel Main Arm
• For reveals5-1/8" (130mm)to 8" (203mm)
• Adjustable friction holder• Handed same as the door• Permits 140° door opening• 160° F link standard• Specify 125° F link when requiredOrder as 25-FZA x hand x finish for arm onlyIncludes: 63-2240 - Left hand main arm assembly
63-2241 - Right hand main arm assembly63-2218 - Foot assembly63-3684 - Screw pack
71-800-727-5477 • www.sargentlock.com
Powerglide® Door Closer Arms for Top Jamb Application351 Series
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
• Forged Steel Main Arm
• For reveals5-1/8" (130mm)to 8" (203mm)
• Adjustable friction holder • Non-handed• Permits 140° door openingOrder as 25-HZA x finish for arm onlyIncludes: 63-2231 - Main arm assembly
61-2303 - Foot assembly63-3684 - Screw pack
HZA - Hold Open Arm for Extra Deep Reveal
• Forged Steel Main Arm
• For reveals from2-1/8" (54mm)to 5" (127mm)
• Adjustable friction holder• Non-handed• Permits 140° door openingOrder as 25-HZ x finish for arm onlyIncludes: 63-2230 - Main arm assembly
61-2303 - Foot assembly63-3684 - Screw pack
• Forged Steel Main Arm
• For reveals from 2-1/8" (54mm) to 5" (127mm)
• Non-handed• Permits 140° door openingOrder as 25-OZ x finish for arm onlyIncludes: 63-2607 - Main arm assembly
63-2217 - Foot assembly63-3684 - Screw pack
• Forged Steel Main Arm
• For reveals5-1/8" (130mm)to 8" (203mm)
• Non-handed• Permits 140° door openingOrder as 25-OZA x finish for arm onlyIncludes: 63-2607 - Main arm assembly
63-2218 - Foot assembly63-3684 - Screw pack
H - Hold Open Arm
OZ - Standard Arm for Deep Reveals
OZA - Standard Arm for Extra Deep Reveal
F- Fusible Link Hold Open Arm
FZ - Fusible Link Hold Open Armfor Deep Reveals
• Forged Steel Main Arm
• For reveals up to2" (51mm)
• Adjustable friction holder• Handed same as door• Permits 140° door opening• 160° F link standard• Specify 125° F link when requiredOrder as 25-F x hand x finish for arm onlyIncludes: 63-2240 - Left hand main arm assembly
63-2241 - Right hand main arm assembly63-2468 - Foot assembly63-3684 - Screw pack
• Forged Steel Main Arm
• For reveals2-1/8" (54mm)to 5" (127mm)
• Adjustable friction holder• Handed same as door• Permits 140° door opening• 160° F link standard• Specify 125° F link when requiredOrder as 25-FZ x hand x finish for arm onlyIncludes: 63-2240 - Left hand main arm
63-2241 - Right hand main arm 63-2217 - Foot assembly63-3684 - Screw pack
HZ - Hold Open Arm for Deep Reveals
• Forged Steel Main Arm
• For reveals up to 2" (51mm)
• Adjustable friction holder
• Non-handed • Permits 180° door openingOrder as 25-H x finish for arm onlyIncludes: 63-2229 - Main arm assembly
61-2303 - Foot assembly63-3684 - Screw pack
• Forged Steel Main Arm
• For reveals up to 2" (51mm)
• Non-handed• Permits 180° door openingOrder as 25-O x finish for arm only Includes: 63-2607 - Main arm assembly
63-2216 - Foot assembly63-3684 - Screw pack
O - Standard Arm
Extra Deep Reveal Arms
Deep Reveal Arms
Available Arms for institutional installations:• Regular duty parallel arms• Offset bracket arms for use with Auxiliary
Holders & Stops• Parallel flush frame arms• Flush frame arms for use with Auxiliary
Holders & Stops• Flush frame, friction Hold Open Arms
8 1-800-727-5477 • www.sargentlock.com
351 Series Powerglide® Door CloserParallel Arm Application
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
P9 ARM SHOWN
NON HOLD OPEN ARMS• Two mounting positions for 120° and
180° maximum door opening
HOLD OPEN ARMS
• Friction hold open arms available fordoors subject to moderate hold open use
• UL Listed fusible hold open armsavailable
Non hold-open arms• Two mounting positions for 120° and
180° maximum door openings
Stop arms• 6 mounting positions allow stop
from 85°–110°
Regular Duty Parallel Arms
Heavy Duty Parallel Arms
351-P9 Regular Duty Parallel Arm
Parallel Arm Applications - The 351 closer is mounted on the pushside of the door. As the door opens, the closer swings with the doorand gives full headroom in the door opening. Other advantages: thecloser arm does not project into the room; the frame can be quitenarrow and the door can be swung open much farther than in Top Jamb Applications.
P9 Parallel Arm
Varies4-1/2" - 7-3/8"
(113mm - 187mm)
1" MIN(25mm)
Varies 5-7/8" to 6-3/8"(149mm to 162mm)
3-7/8"(98mm)
2-3/16"(56mm)13"
(330mm)
For use in high traffic and abusive environments• Forged steel arm and cast iron foot bracket
for strength and durability• Oiled bronze bearings for superior wear
resistance• 2 piece rigid arms for ease of installation• Friction and positive hold open arms
available• Use friction hold open arms for doors
subject to moderate hold open use• Dead stop and compression stop arms
available• Security non-hold open arms available
91-800-727-5477 • www.sargentlock.com
Powerglide® Door CloserHeavy Duty Parallel Arms351 Series
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
PS - Heavy Duty Parallel Arm withPositive Stop
• Forged Steel Constructions• Handed arm is field-reversible• Provides built in stop from 85° to 110°• Permits 110° opening maximum• Easily installed• Permits 85° to 110° door openingOrder as 25-PS x finish for arm onlyIncludes: 63-0641 - Main arm
63-3837 - PS foot assembly63-3684 & 63-2398 - Screw packs
PSH - Heavy Duty Parallel Hold OpenArm with Positive Stop
P10 - Heavy Duty Parallel Arm
• Forged Steel Constructions• Non-Handed• Easily installed• Permits 120° opening at standard
mounting• Permits 180° opening at alternate
mountingOrder as 25-P10 x finish for arm only25-P10 Includes: 63-0641 - Main arm
63-3727 - P10 foot assembly63-3684 & 63-2392 - Screw packs
• Forged Steel Constructions• Provides built in compression stop
from 85° to 105°• Permits 105° opening maximum• Easily installed• Handed arm is field-reversible• Dead stop within 3°Order as 25-CPS x finish for arm onlyIncludes: 63-0641 - Main arm
63-3830 - CPS foot assembly63-0516 - Bumper holder63-3493 - Bumper63-3684 & 63-2398 - Screw packs
CPS - Heavy Duty Parallel Armwith Compression Stop
• Forged Steel Constructions• Handed arm is field-reversible• Provides built in compression stop
and holder mechanism from 85° to 105°• Easily installed/adjusted• Permits 105° opening maximum• Dead stop within 3°Order as 25-CPSH x finish for arm onlyIncludes: 63-0641 - Main arm
63-3836 - CPSH foot assembly63-0516 - Bumper holder63-3493 - Bumper63-3684, 63-2392 & 63-3487 - Screw packs
CPSH - Heavy Duty Hold OpenParallel Arm with Compression Stop
SP10 Heavy Duty Security Arm
• Same as P10, except factory assembled at arm joint (elbow) to prevent disassembly in SSP package alongwith metal cover
• Forged Steel Constructions• Provides holder and stop features• Handed arm is field-reversible• Easily installed/adjusted• Permits 85° to 110° door openingOrder as 25-PSH x finish for arm onlyIncludes: 63-0641 - Main arm
63-3833 - PSH foot assembly63-3684, 63-2392 & 63-2398 - Screw packs
The PSH and CPSH arms project 2 3/4"below the head stop
• Forged Steel Constructions• Adjustable hold open from 75° to 180°• Forged steel arm 11-1/4" (286mm) long• Handed same as door• Use friction hold open arms for doors
subject to moderate hold open useOrder as 25-PH10 x finish for arm only25-PH10 Includes:63-0641 - Main arm63-3839 - Left hand PH10 foot assembly63-3840 - Right hand PH10 foot assembly63-3684 & 63-2392 - Screw packs
PH10 - Heavy Duty Friction HoldOpen Parallel Arm
Positive Stop Hold Open Arms(PSH & CPSH ARMS)
• Use on doors subject to repetitive holdopen use
• 6 hold open positions from 85° to 110° determined by mounting position
• Hold open function may be disengaged• Hold open tension is easily adjustable
Regular Duty Hold Open Arms
10 1-800-727-5477 • www.sargentlock.com
351 Series Powerglide® Door CloserRegular Duty Parallel Arms
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
• Forged Steel Main Arm
• Non-handed
Order as 25-P9 x finish for arm onlyIncludes: 63-2607 -Main arm
63-2271 -Foot assembly63-3684 & 63-2391 - Screw packs
Regular Duty Offset Bracket Arms
• Forged Steel Main Arm
• Holds openfrom 75° to 180°
• Easily adjusted bywrench
• Non-handedOrder as 25-PH9 x finish for arm onlyIncludes: 63-2229 - Main arm
61-2303 - Foot assembly64-0039 - Foot bracket (125 PH9)63-3684 & 63-2391 - Screw packs
PH9 - Friction Hold Open Arm
P4 - Parallel Flush frame Arm
• Forged Steel Main Arm
• For use with auxiliary surface overheadstops andholders
• Foot bracketis offset 1" more than P-9, allowing door closer to be lowered on door face
• Non-handedOrder as 25-P3 x finish for arm onlyIncludes: 63-2607 -Main arm
63-2270 -Foot assembly63-3684 & 63-2391 - Screw packs
• Forged Steel Main Arm
• Foot bracket is attached to frame or transom face
• For use where stop or soffit is too narrow for the standard P9
• Permits 120° opening withstandard mounting
• Permits 180° opening withalternate mounting
• Non-handedOrder as 25-P4 x finish for arm onlyIncludes: 63-2607 -Main arm
63-2295 -Foot assembly63-3684 & 63-2391 - Screw pack
• Forged Steel Main Arm
• For use with auxiliary surfaceoverheadstops andholders and door coordinators
• Foot bracket lowers door closer an additional 3/4" below P3 bracket
• Non-handedOrder as 25-P3A x finish for arm onlyIncludes: 63-2607 -Main arm
63-2274 -Foot assembly63-3684 & 63-2391 - Screw packs
• Forged Steel Main Arm
• For use with auxiliary surface overheadstops andholders
• Foot bracket is attached to frameor transom face
• Foot bracket lowers door closer an additional 3/4" below P4 bracket
• Non-handedOrder as 25-P4A x finish for arm onlyIncludes: 63-2607 - Main arm
63-2272 - Foot assembly63-3684 & 63-2391 - Screw packs
P3 - 1" Offset Bracket for use with Auxiliary Holder/Stop
P3A - 1-3/4" Offset Bracket for usewith Auxiliary Holder/Stop
P4A - Flush Frame Arm for use with Auxiliary Holder/Stop
P9 - Standard Parallel Arm
• Forged Steel Main Arm
• Fusible linkmelts andreleasesholdmechanism allowing door to close
• 160°F fusible link standard;125°F link optional
• Equipped with adjustable friction holder• Holds door open from 75° to 180°• Easily adjusted by wrench• Handed same as doorOrder as 25-PF9 x hand x fusible link degree x finish for arm onlyIncludes: 63-2229 - Main arm
63-2245 - Left hand foot assembly63-2246 - Right hand foot assembly63-3684 & 63-2391 - Screw packs
PF9 - Fusible Link Hold Open Arm
UO Package • Universal arm
package provides armsand brackets to installcloser in standardtop jamb orparallel application
351-UO not available with (MC) metal cover or plated finishes
Screw pack63-3684
125-P9
UH Package• Universal hold
open arm package provides brackets and arms to install closer in top jamb, standard or parallel applications
351-UH not available with (MC) metal cover or plated finishes
Screw pack63-3684
125-PH9
• Forged Steel Main Arm
• Holds open from75° to 180°
• Easily adjusted bywrench
• Non-handed• Use on frames where stop or soffit is
too narrow to mount the standard hold open foot bracket
Order as 25-PH4 x finish for arm onlyIncludes: 63-2229 - Main arm
61-2303 - Foot assembly64-0050 - Foot bracket63-3684 & 63-2391 - Screw packs
P4H - Flush Frame, Friction HoldOpen Arm
Heavy Duty Parallel Arm Accessories
111-800-727-5477 • www.sargentlock.com
Powerglide® Door CloserAccessories For Parallel Applications351 Series
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
• Converts O or P9 Arm to P4A Arm • Converts O or P9 arm to P4A Arm
581-1 Blade Stop Spacer Kit125-P4A Arm Conversion Unit125-P4 Conversion Unit
Regular Duty Parallel Arm Accessories
Parallel Arm Mounting Plates
• For frames with 1/2" blade stops• For use with P10, PH10, PS, PSH,
CPS and CPSH arms• 125-V bracket included• Packed with 1-1/4" long screwsUse P/N 63-0756 to order blade stop only
• Permits mounting parallel arm 351 SeriesCloser applications on doors with narrowtop rails
• Requires 3" (76mm) minimum top rail• For closers used with overhead stops and
holders, top rail requirements will varydepending upon type and make of holder
• Available with powder coat and platedfinishes to match door closer
• Plates are not handed• Plate mounting screws included• Order as 351-D x finish
• Converts O-P9 arm to P3 Parallel Arm • Converts O or P9 Arm toP3A Parallel Arm
• Converts standard hold open (H) arm to PH9 Parallel Hold Open Arm
351-D Drop Plate
581-2 Blade Stop Spacer Kit
125-PH9 Parallel Arm Foot125-P3A Arm Conversion Unit125-P3 Arm Conversion Unit
• Included with all heavy duty arms
Spacer 63-0191125-V/125-VF Brackets
125-V 125-VF• For use with all heavy duty parallel arms• Use 125-V for narrow stop
and frame conditions• Use 125-VF for flush door
and frame conditions
• For frames with 1/2" blade stops• For use with P9, PH9 and PF9 arms only• Packed with 1-1/4" long screws
3" MIN.( 76MM)
351-DDROP BRACKET
9"(229mm)
6"(152 mm)
351L - LCN RETROFIT PlateDesigned to replace a LCN 4040 closer bodywith a SARGENT 351 without drilling newholes in door (NOTE: new mounting holesrequired for arm bracket only)
• Plates are non-handed• Available in powder coat and plated finishes• Order as: 351L x finish• Consult factory when replacing LCN stop arm
12 1-800-727-5477 • www.sargentlock.com
351 Series Powerglide® Door CloserTrack Type Applications
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
Push Stop Side Mounting (Track mounts on frame stop)• Minimum top rail required without drop plate = 5-3/4" (146mm) • 3" (76mm) minimum top rail required with 351-D Drop Plate
Minimum Stop Required• 1-9/16" (40mm) wide
Maximum Door Opening• 100° with standard track• 95° with optional bumper track
Hold Open Range• 85° to 95°
Pull Hinge Side Mounting (Track mounts on frame face)• Minimum top rail required with a 351-A plate = 2-1/4" (57mm)• Minimum top rail required without mounting plate= 4" (102mm)
Maximum Door Opening• 160° with standard track• 120° with optional bumper track• 180° with standard track if frame conditions permit
Hold Open Range• 85° to 120°
Pull Side Track ApplicationArm & Track Description
Pull Side Mounting (Hinge Side)
The closer is for use on interior doors opening in or out. As thedoor opens, the closer swings with the door. This affords a variablehold-open feature option.
Standard Finishes• EAB, EB, ED, EN, EP, powder coated on
all exposed surfaces• Architectural plated arms and covers
optional
Track• Extruded aluminum track
OT Pull Standard pull side
OTB Pull Track with bumper
HT Pull Holder
HBT Pull Holder with bumper
OT Shown
Track Arm Applications
24"
4"
2-3/16"17-7/8"
Arm• Forged steel
Bumper (optional)• Mounts in track to assist backcheck • Not designed to be used as a stop • Auxiliary stop is required• Available for both regular or hold open tracks
Holder (optional)• Mounts within the track (adjustable)
Non Sized-Adjustable• Interior doors to 5'0" wide• Shipped factory preset for 3'0" door• Factory pre-sized upon request
Push Side Mounting (Stop Side)
The closer is for use on interior doors opening in or out. As thedoor opens, the closer swings with the door. This affords a variablehold-open feature option.
Push Side Track ApplicationArm & Track Description
POT Push Standard
POTB Push Bumper
PHT Push Holder
PHTB Push Holder and bumper
POT Shown
Track Arm Applications
24"
17-7/8"
5 3/4""
Common Features
131-800-727-5477 • www.sargentlock.com
Powerglide® Door CloserDouble Egress Application351 Series
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
OD Applications• 160° maximum door opening• 120° opening with bumper option• Range of hold open: 85°-120°• Used with reveals 3" to 4" (76mm-101mm)
Track• Extruded aluminum track• End caps finished to match track
Arm• Forged steel• Bearing roller• Arm is handed same as door
Non Handed• Universal Body
Finishes (Powder Coat)• EAB, EB, ED, EN, EP (standard for all
exposed surfaces)
Bumper (optional)• Mounts in track to assist backcheck• Not designed to be used as a stop• Auxiliary stop is required• Available for both regular or hold open
tracks
Holder (optional)• Mounts within the track (adjustable)
Non Sized-Adjustable• Interior doors to 5'0" wide• Shipped factory preset for 3'0" door• Factory pre-sized upon request
OD - Double Step Double Egress ArmODS - Single Step Double Egress Arm
1-3/16"(30mm)
3" – 4"(76-102mm) 5/8"
(16mm)
1/4" Maximum Frame Projection Permitted From Face of Door
Single Step Frame Double Step Frame
23-5/8" (600mm)
1/8-3"
4-3/8"Min top
rail
2-3/16"
18-1/2"
ODS Applications• 160° maximum door opening• 120° opening with bumper option• Range of hold open 85°-120°• Used with reveals 1/8" to 3" (3mm-76mm)
Track• Extruded aluminum track• End caps finished to match track
Arm• Forged steel• Bearing roller• Arm handed same as door
Non Handed• Universal body
Finishes (Powder Coat)• EAB, EB, ED, EN, EP (standard for all
exposed surfaces)
Bumper (optional)• Mounts in track to assist backcheck• Not designed to be used as a stop• Auxiliary stop is required• Available for both regular or hold open
tracks
Holder (optional)• Mounts within the track (adjustable)
Non Sized-Adjustable• Interior doors to 5'0" wide• Shipped factory preset for 3'0" door• Factory pre-sized upon request
Double egress track arms are used when theaesthetics of a track application is requiredon the pull side of a deep reveal frame.
This application is commonly used on crosscorridor openings.
4" Minimum(102mm)
Top Rail Required
Double Egress Track Applications
OD Double step double egress
ODB Double step double egress with bumper
HD Double step double egress with holder
HDB Double step double egress with bumper and holder
ODS Single step double egress
ODSB Single step double egress with bumper
HDS Single step double egress with holder
HDSB Single step double egress with bumper and holder
14 1-800-727-5477 • www.sargentlock.com
351 Series Powerglide® Door CloserPocket Door Application
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
Wall Magnets - see SARGENT holders and stops catalog
Pocket door applications commonly use wall mounts (wall magnets).
1560 Surface Mount
14
1-3/4"
6-1/8"
2-1/4"
DOOR
Pocket Depth2-5/8" Min4-1/8" Max
WALL
POCKET DEPTH2-5/8" MIN4-1/8" MAX
2-1/4"
DOOR
WALL
1-3/4"
6-1/8"
OTP - Track Type ApplicationOP - Double Lever Arm Application
Pocket Door ApplicationsThe 351 Series Powerglide Door Closer body is mounted on the wall and installed so that it pushes the door closed. This application is typicallyused with fire doors that are held open. In this application when the door is open, the closer and arms are completely hidden from view.
Wall Door in Closed Position
Wall Door in Closed Position
18-3/4"7"
WALL DOOR
6-13/16"
2-1/8"
1 3/4"
Pocket Depth2-5/8" Min4-1/8" Max
1561 Flush Mount
26-3/8"
17"6-13/16"
2-1/8"
DOORWALL
7"
18-3/4"
OP - Pocket Arm Application• 180° Maximum Opening• Non handed
Arm• Forged steel
Non Handed• Universal Body
Finishes (Powder Coat)• EAB, EB, ED, EN, EP (standard for all exposed surfaces)• Plated Covers and arms available
Wall
Top View
Door
Wall
Top View
Door
OTP - Track Type Application• 90° Maximum Opening• Extruded Aluminum Track• Non handed
Arm• Forged steel• Bearing roller
Non Handed• Universal Body
Finishes (Powder Coat)• EAB, EB, ED, EN, EP (standard for all exposed surfaces)• Plated Covers and arms available
151-800-727-5477 • www.sargentlock.com
Powerglide® Door CloserOverhead Stop/Holder Compatibility351 Series
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
Frequently Used Overhead Stops used with the 281 Series
When a floor or wall stop cannot be used the highest level of door control is provided with the use of a SARGENT door closer and aSARGENT overhead stop or holder. While door closer arms are available with stop and holder options, they are limited in their ability towithstand extreme abuse. Overhead stops absorb abusive loads using a heavy compression spring that distributes the load to the frame.SARGENT overhead stops and holders are designed for years of abuse and come with a 5 year warranty
• Standard Door Closer Applications (PULL SIDE MOUNT) Not Shown590 Series Holder/Stop with 351-O690 Series Holder/Stop with 351-O1530 Series Holder/Stop with 351-O1540 Series Holder/Stop with 351-O
• Parallel Arm Door Closer Applications (PUSH SIDE MOUNT)590 Series Holder/Stop with 351-P3590 Series Holder/Stop with 351-PD10690 Series Holder/Stop with 351-P9690 Series Holder/Stop with 351-P101530 Series Holder/Stop with 351-P91530 Series Holder/Stop with 351-P101540 Series Holder/Stop with 351-P31540 Series Holder/Stop with 351-PD10
• Parallel Arm Door Closer Applications Used with a Flush Frame590 Series Holder/Stop with 351-P4690 Series Holder/Stop with 351-P41530 Series Holder/Stop with 351-P41540 Series Holder/Stop with 351-P4
• Inverted Top Jamb Applications590, 690, 1530, 1540 Series with either 281, 351,1431 Series and “O” 0Z, 0ZA Arm
Frame
Door590
Special Conditions
The SARGENT Website (www.sargentlock.com) contains templates for all common applications of SARGENT Door Closers with SARGENToverhead door holders. To ensure a satisfactory installation for other holders, it is recommended that complete details be submitted as follows:
• Type, size and make of holder • Closer application being used
• Holding position (maximum door opening) • Size and type of hinge
• Submit holder template being used
In the case of unusual door, frame and hinge conditions where regular products do not meet requirements, submit drawings andcomplete details specifying the degree of door openings required, the type and size of hinge and the maximum door opening angle.
Through-bolts and Mortise Nuts
• When through-bolting is ordered, factory will furnish mortise nuts for use with the machine screws furnished with the closer
• Nuts are sized to accommodate 1-3/4" (44mm) standard or 1-3/8" (35mm) thick doors when specified on order
• For 2-1/4" (57mm) thick doors, through-bolts will be furnished with mortise nuts
• A bridge type reinforcement is required to prevent collapse of top rails when through-bolts are tightened (required on hollow metal doors).
16 1-800-727-5477 • www.sargentlock.com
351 Series Powerglide® Door CloserHow to Order
6/1/
08Co
pyrig
ht ©
200
5, 2
008,
SAR
GEN
TM
anuf
actu
ring
Com
pany
, an
ASSA
ABL
OY
Gro
up c
ompa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
n in
who
le o
r in
part
with
out t
he e
xpre
ss w
ritte
n pe
rmis
sion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
Series Number per Carton Approx. wt per CartonPackingAll closer assemblies are packaged 4 per carton. On request, door closerswill be be packed 2 per carton.
How To Order Complete Door Closer ExampleSeries 351 351Delayed Action When delayed action is required specify suffix DA 351 DAArm with Closer See applicable catalog section for arms available 351 DA P10Finish, powder coated EB — Bronze Enamel to match 10B 351 DA P10 EBon all exposed surfaces ED — Bronze Enamel to match 20D
EN — Aluminum EnamelEP — Bronze Enamel to match US10EAB — Brass Enamel to be used with brass finishes Optional Plated Finishes (Handed metal cover required)
Symbol BHMA Description3 605 Polished Brass4 606 Dull Brass9 637 Bright Bronze, Clear Coated10 612 Dull Bronze
10B 613 Oxidized Dull Bronze, Oil Rubbed26 625 Chrome
26D 626 Dull ChromeHand (Applies to F, PH and DE armsand metal covers only) Non-handed 351 DA P10 EBThrough Bolts and When ordering mortise nuts, use suffix TB 1-3/4"(44.5mm) 351 DA P10 EB TBMortise Nuts std door thickness. For all others, specify Corrosion Protection Special rust inhibitor process (arm only) suffix SRI 351 DA P10 EB TB SRI
for additional protection in corrosive environments
Note: MicroShield™ can be added to your door closer. Specify prefix SG when ordering.
How To Order Accessories ExampleArm Only Specify arm required and finish 25-PSH ENArm conversion Units Specify unit and finish 125-P4 EBCover Only (Standard) 351-C x finish 351-C ENCover Only (Metal) 351-MC x finish and hand and arm type 351-MC + 26D + LHAccessories Specify accessory and finish -
See applicable catalog section 351-D EBWhen complete closer assembly is ordered with an accessory, order accessory as a separate item
351 4-Standard (2 upon request) 19 lbs. per 4
Screw Prefix 36 — 6 lobe screws
PULL SIDE PULL SIDE
PUSH SIDE PUSH SIDE
LEFT HAND DOOR RIGHT HAND DOOR
Special Rust Inhibitor Process (SRI)Additional process available for bracketand arms provides an extra layer ofprotection for extreme corrosiveenvironments. Specify SRI as suffix when ordering
Plated Finish Notes• A metal cover is automatically provided with plated finishes
• The MC suffix is also used when a metal cover is desired with a painted finish
• When added to a plated finish, the MC suffix indicates that only the cover isto be plated, the arms will be powder coated to match
• Do not specify the MC suffix if both the cover and arms are to be plated
09/05/08
Copyright©1998-2008,SargentM
anufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentM
anufacturingCompanyisprohibited.
• This revolutionary finish coating available on all SARGENT product lines, utilizes asilver-based antimicrobial compound from Agion® Technologies
• The MicroShield protection is now available integrated within the 80 Series touchpad as well as the finish coating. MicroShield lasts for the life of the finish
• MicroShield coating permanently suppresses the growth of bacteria, algae, fungus,mold and mildew. It is effective against a broad spectrum of bacteria
• Non-toxic and completely safe. The Agion antimicrobial compound is EPA and NSFapproved and FDA listed for use in medical and food preparation equipment
• Applications: Anywhere there is need for a clean environment (hospitals,laboratories, schools, medical centers, daycare, food processing etc.)
1-800-727-5477 • www.sargentlock.com2
80 Series 80 Series Exit DevicesFeatures
Strength & Durability• Made of finest component materials• Heavy duty mounting construction• Built to withstand abusive conditions• Available options to meet Dade County Protocols and other localhurricane code requirements for highwind load andmissile impact*
• 5 Year warranty* Consult factory
SARGENT manufactures a full line of exit devices including vertical rod, rim and mortise devices for both standard and narrow stile doors. Thesedevices provide the best combination of simplicity, strength, durability, aesthetics and innovation and are perfect for applications in commercial officebuildings, medical and educational institutions.
Innovation• SARGENT introduces Beacon™, a next generation exit device thatcreates a clearer pathway to safety during an emergency. Thecombination of audible and visible alerts built into the exit devicemakes Beacon unique – and effective.
• Broad offering of electro-mechanical solutions for the mostdemanding access/egress control applications
• MicroShield™ anti-microbial finish coating offers a new levelof protection
• SARGuide™ exit device contains an electroluminescent touchpad toenhance the visibility of exit locations in dark or smoke-filled passagesand effectively improve the safety of any public building
• CTL (Center and Top Latching) Vertical Rod Devices offer less bottomrod convenience with true center latching for added security
Security• Double cylinder functions available• Torx® and spanner screws• Anti-vandal trim options• Master keying with SARGENT Security Key systems available(V-10, Signature, Keso F1, Keso and XC)
Microshield™ Coating
• The SARGuide illuminated exit device increases visibility of exitlocations in dark or smoke-filled passages, supplementing existingcodes for egress lighting
• SARGuide utilizes state-of-the-art FLATLITE electroluminescent lightingfrom E-Lite Technologies Inc.
• Green-blue electroluminescent light provides 3 to 5 times the visibilityof other lights
• Can be wired for continuous operation or activation by fire alarm system• Exit devices are placed low enough on a door to provide an extendedwindow of opportunity for safe emergency egress
• Supplements building exit signs required by code• Intuitive operation. Integral “EXIT” signage guides users directly to themeans of egress
• UL Listed for use on panic (UL 305) and fire-rated (UL10C) exit devices• Available with mechanical, and many electro-mechanical, exit devices• See pages 56 & 57 for information on the TL- & PL- offerings
Simplicity• Easy installation!• Maintenance-free design• Few moving parts – less wear• Modular construction• Rekeying is accomplished without removing device from door
Aesthetics• Clean, simple, aesthetically pleasing design• “True” architectural hardware finishes consistent with BHMA/ANSIstandards
• Coastal Series and Studio Collection Levers adds a touch of elegance
MicroShield™As part of their promise to provide innovative solutions to their customers,ASSA ABLOY Group companies offer the MicroShieldTM technology, a silver-basedantimicrobial coating designed to stem the spread of germs and bacteria.
MicroShieldTM is a trademark of Yale Security Inc., an ASSA ABLOY Group company.
The Agion antimicrobial is not intended as a substitute for good hygiene.Coated products must still be cleaned to insure the surfaces will be free ofdestructive microbes. ASSA ABLOY makes no representations or warranties,express or implied, as to the efficacy of the Agion antimicrobial. A copy ofthe Agion warranty is available upon request.Agion is a registered trademark of Agion Technologies, Inc., Wakefield, MA, USA
09/05/08
Copyright©1998-2008,SargentM
anufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentM
anufacturingCompanyisprohibited.
1-800-727-5477 • www.sargentlock.com 3
80 Series 80 Series Exit DevicesUL Fire Door Ratings andOpenings Sizes
Maximum Door Opening-Fire Doors
Exit Device DoorMaterial Single Door
Double Door Applications
with12-HC980 or12-980 or12-L980 or12-HCL980Mullion
with12-HD980Mullion
VR/VRDoors Swing
SameDirection
SVR/MortiseDoors Swing
SameDirection
CVR/MortiseMD DoorsSwing SameDirection
CVR/MortiseWD DoorsSwing SameDirection
VR/VRDouble Egress
12-8800 Metal 3 Hour 4' x 10' 3 Hour 8' x 8' 3 Hour 8' x 10' –– –– –– –– ––
12-8800 Wood 3 Hour 4' x 10' 3 Hour 8' x 8' 3 Hour 8' x 10' –– –– –– –– ––
12-8900 Metal 3 Hour 4' x 10' –– –– –– 3 Hour 8' x 8' 3 Hour 8' x 10' –– ––
12-8900 Wood 3 Hour 4' x 10' –– –– –– 3 Hour 8' x 8' –– 3 Hour 8' x 9' ––
12-8300 Metal 3 Hour 4' x 10' –– –– –– –– 3 Hour 8' x 10' –– ––
12-8300 Wood 3 Hour 4' x 10' –– –– –– –– –– 3 Hour 8' x 9' ––
12-FM8700 Metal 3 Hour 4' x 7' –– –– 3 Hour 6' x 7' –– –– –– ––
12-8700 Metal –– –– –– 3 Hour 8' x 8' 3 Hour 8' x 8' –– –– 3 Hour 8' x 8'
12-8700 Wood –– –– –– 3 Hour 8' x 8' 3 Hour 8' x 8' –– –– 3 Hour 8' x 8'
12-NB8700 Metal –– –– –– 3 Hour 8' x 8' –– –– –– 3 Hour 8' x 8'
12-NB8700 Wood –– –– –– 3 Hour 8' x 8' –– –– –– 3 Hour 8' x 8'
12-SP8700 Metal 90Min 4' x 10' –– –– –– –– –– –– ––
12-SP8700 Wood 90Min 4' x 9' –– –– –– –– –– –– ––
12-PP8700 &12-PR8700 Metal –– –– –– 3 Hour 8' x 10' –– –– –– 3 Hour 8' x 10'
12-PP8700 &12-PR8700 Wood –– –– –– 3 Hour 8' x 8' –– –– –– 3 Hour 8' x 8'
12-MD8600 Metal –– –– –– 3 Hour 8' x 10' –– 3 Hour 8' x 10' –– 3 Hour 8' x 10'
12-NB-MD8600 Metal –– –– –– 3 Hour 8' x 10' –– –– –– 3 Hour 8' x 10'
12-WD8600 Wood –– –– –– 90Min 8' x 9' –– –– 3 Hour 8' x 9' 3 Hour 8' x 9'
12-NB-WD8600 Wood –– –– –– 90Min 8' x 9' –– –– –– 3 Hour 8' x 9'
12-MD8400 Metal –– –– –– 3 Hour 8' x 10' –– 3 Hour 8' x 10' –– 3 Hour 8' x 10'
12-NB-MD8400 Metal –– –– –– 3 Hour 8' x 10' –– –– –– 3 Hour 8' x 10'
12-SP8600 Metal 3 Hour 4' x 10' –– –– –– –– –– –– ––
12-SP8600 Wood 45Min 4' x 9' –– –– –– –– –– –– ––
12-PP8600 &12-PR8600 Metal –– –– –– 3 Hour 8' x 10' –– –– –– 3 Hour 8' x 10'
12-PP8600 &12- PR8600 Wood –– –– –– 90Min 8' x 8' –– –– –– 45Min 8' x 8'
12-LS8600 Metal 3 Hour 4' x 10' –– –– –– –– –– ––
12-LP8600 &12-LR8600 Metal –– –– –– 3 Hour 8' x 10' –– –– –– 3 Hour 8' x 10'
CVR/Mortise
CVR
SVR/Mortise
SVR
MortiseLock
Rim
Type
09/05/08
Copyright©1998-2008,SargentM
anufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentM
anufacturingCompanyisprohibited.
648 & 653 Strikes (Alternate Strikes for 8700 SVR Devices)
8700 SeriesSurface Vertical Rod Exit Device
624 Bottom Strike
• Standard for 8700• Applied to surface of flooror to a flat threshold
• Black nylon coated
2-1/2"(64mm)
3/8"(10mm)
9/16"(14mm)
Specifications for 8700 Series Exit
Features• Two point latching (top and bottom of the door)• Top & bottom latchbolt projection adjustable through center case• Standard bottom latch compatible with latchtrack thresholds (by others)• Single and double door applications• Devices are ANSI A156.3 – 2001 Grade 1• UL Fire and Panic listed• Rods are 1/2" (13mm) brass, bronze or stainless steelNote: The 8700 Exit Device can not be used less bottom rod. If less bottom rodis desired, specify NB8700 Series Exit Device.
646 Top Strike
• Standard for both Panic &Fire (12-) Hardware
• Surface applied to frame• Black nylon coated• Replaces 629 Strike
1-5/32"(29mm)
3-11/16"(94mm)
3/4"(19mm) 1/4"
(6mm)
655 Bottom Strike
• Standard for 12-8700 and14-8700
• Stainless steel• Black nylon coated• Replaces 647 Strike
2-3/4"(70mm)
1-13/16"(46mm)
Inside Lever Assemblyfor 300 Series Aux Control
Attaches to top rod andengages with 300 SeriesAuxiliary Control. Packedstandard with 306 and 313Auxiliary ControlsPart # 97-2378
1-800-727-5477 • www.sargentlock.com14
80 Series 8700 Surface Vertical Rod Exit Device
Alternate for 12-8700
1-1/8"(29mm)
1 7/8"(48mm)
7/16"(11mm)
2-1/2"(64mm)
1/2"(13mm)
1-3/4"(44mm)
2-3/4"(70mm)
2-5/16"(59mm)2-1/8"
(54mm)
648 StrikeFor doors havingtransom panelapplications
Black nylon coated
653 Strike
Black nyloncoated
Door Types Wood or metal 1 3/4" (44 mm) minimum thickness. For doors over 1-3/4"to 2-1/4" thick, specify thickness and order as 31- prefix4-1/2" (114mm) minimum stile with trim and3-1/2" (44mm) minimum stile without trim.
Door Widths E Rail - 24" to 32" (61cm to 81cm) No cutting required for 32" doorF Rail - 33" to 36" (84cm to 91cm) No cutting required for 36" doorJ Rail - 37" to 42" (94cm to 107cm) No cutting required for 42" doorG Rail - 43" to 48" (110cm to 122cm) No cutting required for 48" door
Strike 649 Top Strike (Panic and Fire Rated)624 Bottom Strike; 655 Fire Rated Bottom Strike
Dogging Feature Hex key dogging standard; Cylinder dogging available (16-)Electric Options AL- Alarmed Exit Device - Page 56
BT- Beacon™ Exit Device - Page 55PL- SARGuide Photoluminescent Coated Push Rail - Page 56TL- SARGuide Illuminated Touchpad - Page 5753- LX Latchbolt Monitor Switch - Page 5754- Outside Lever Monitoring - Page 6255- Request-to-Exit Signal - Rail Monitoring - Page 5756- ELR Remote Latch Retraction - Page 5857- Delay Egress Exit to be used in conjunction with Electromagnet - Page 6058- Electric Dogging - Page 6159- Electroguard – Self contained Delayed Egress Device - Page 61
Mounting Fasteners Supplied standard with wood and machine screwsAvailable with through-bolts and mortise (sex) nuts
Top & Bottom Bolt Brass, Stainless steelDevice Centerline from 41” (1041 mm) for Standard Applications; 38" (965mm) for elementary
schools and to meet local accessibility standards when a 300 Series AuxiliaryControl is used
Door/Opening Height Must be specified - 120" (3048 mm) Max Door OpeningCenter Case Dimensions 8-3/8" (213mm) x 2-5/8" (67mm)Projection Pushbar Neutral – 3" (76 mm)
Pushbar Depressed – 2-1/8" (54 mm)Fire Exit Hardware See Chart – Page 3
1-800-727-5477 • www.sargentlock.com 63 09/05/08
Copyright©1998-2008,SargentM
anufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentM
anufacturingCompanyisprohibited.
L Rail 36" (91cm) No cuttingrequired
M Rail 42" to 44" No cutting(107cm to 112cm) required
N Rail 46" to 48" No cutting(117cm to 122cm) required
10 Signature System10-UL Signature, meets UL437 cylinder+11 SARGENT XC Key System12 UL Fire Label Exit Devices14 Sliding bolt bottom case for 8700++16 Cylinder lockdown feature19 Pushbar without Lexan touchpad21 Construction Keying Conventional, XC
and Signature Series22 Construction Keying Conventional
Cylinders (Existing Systems Only)23 ANSI flat lip strike (8300, 8900,
including 12- Prefix)*31 Doors over 1-3/4" and/or Panels36 6 Lobe security head screws37 Spanner head screws43 Flush End Cap*53 Latchbolt monitoring switch54 Internal micro switch in ET Control55 Signal Switch in Rail (Request to Exit)56 Remote Dogging/Latch Retraction56-HK Remote Latch Retraction with manual Hex
Key dogging57 DelayedEgress (Magnetorderedseparately)58 Electric Dogging**59 Electroguard® Self Contained Delayed
Egress Device**BC59 Electroguard Boca Code (Door Status Switch
required)60 Disposable Construction Core63 SARGENT Removable Core cyl. Includes
masterkeying, grand masterkeying64 SARGENT Removable Construction Core
cylinder65-73 6 Pin Uncombinated Small Format
Interchangeable Cores65-73-7P 7 Pin Uncombinated Small Format
Interchangeable Type Cores70 Exit device to accept Small Format
Interchangeable Cores - no core provided72 Exit device to accept Small Format
Interchangeable Cores with ConstructionCore provided
73 Small Format 6-Pin interchangeable core(refer to CK-8 for available keyways)
73-7P Small Format 7-pin interchangeable core,(refer to CK-8 for available keyways)
75 Warning inside, Abrasive strip on rail76 Knurled Outside Lever77 Warning inside and outside, abrasive strip
on rail, abrasive coating on Lever81 Cylinder to accept Keso (83) and Keso F1
(F183) removable core – no core providedF1-82 Keso Security Cylinder with Front
Profile (Patent Pending)82 Keso Security CylinderF1-83 Keso Security Removable Core Cylinder
with Front Profile (Patent Pending)83 KesoSecurityRemovableCoreCylinder84 Keso Security Removable Construction
Core CylinderAL Alarmed ExitBR Bump Resistant Cylinder (Available with
Conventional & XC Cylinders Only)***BT Beacon- Emergency Audio & Visual egress
system with a self contained Laser, FlashingLEDs & Audio alert
GL Guarded Latchbolt for 8800NB No Bottom Rod (Not available with 59- &
BC59- )PL SARGuide™ PL – Photoluminescent Coated
Push Rail – (Touchpad eliminated)SC, SE Exit Device furnished in Schlage C or E
Keyway (specify)SG MicroShield - Antimicrobial clear powder coatTL SARGuide Illuminated touchpadVA, VC, SARGENT V-10 CylindersVS, VC, VS See V-10 Cylinder Section
Cylinder Notes:• 16- Cylinder Dogging uses a 41 insidecylinder with 97 ring
• Removable core and 70 prefix cylindersrequire a 97-0351 cylinder rings for 700Series ET Controls and 94-0153 ring for 100 &300 Series Aux controls
• Less cylinder - SARGENT supplies standardblocking rings. Specify if using competitorcylinders
• When ordering BEST cylinders for use inSARGENT Exit Devices, use the following BESTproduct numbers:Mortise cylinder: 1-E74XC208Rim cylinder: 1ESPL-7-AO5994
Notes For Prefixes• 31- Specify door thickness and specify panelthickness and location, if used
• 31- prefix not available, HC8700, FM8700,PP, PR & SP8700, PP, PR & SP8600, LP, LR &LP8700,
• 31- Prefix requires extended lip strike for8300 & 8900 Series (supplied).
• SC- Prefix not available in 57- Prefix,(SC- Cylinders are only available in 41 lengthcylinders and Rim cylinders)
• SC-, SE- & VC- Prefixes not available with thefollowing: 8904, 8916, 8944, 8975, 8976,8866, 8304, 8344, 8375 & 8376 (SC- & SE-#41 cylinders only & VC- #42 cylinders only)
+ 11- Prefix not available with 10-, 10-UL-, 22-,60-, 63-, 64- SE, SC, 82-, F1-82-, 82-, F1-83- &84- prefixes.
++16- Prefix not available with 12-, 57, 59- orAL- prefix
* 53- Not available on PP/PR/SP8600 &LP/LR/LS8600 Exit Devices** 59- & BC59- are not available with 16-, 55-,56-, 57-, 58- prefixes and on NB8700,PP/PR/SP8600 & LP/LR/LS8600 Exit Devices
*** BT- Not available FM8700 Devices & thesesprefixes 16-, 56-, 57-, 59-, BC59- and AL
SuffixCPC Clear Powder Coat – Recommended forexit devices used in full exterior application andhighly corrosive areas with 32 and 32D finishes.How to order: 8313F x ETL x 32D x CPC
Note: For additional information on ElectrifiedExit Devices, see the Electrified Exit Devicecatalog at www.sargentlock.com
Prefixes Available
E 24" to 32" No cutting required(61cm to 81cm) for 32"(81cm) door
F 33"to 36" No cutting required(84cm to 91cm) for 36" (91cm) door
J 37" to 42" No cutting required(94cm to 107cm) for 42" (107cm) door
G 43" to 48" No cutting required(110cmto122cm) for 48" (122cm) door
Rail SizesSARGENT offers four sizes of rails toaccommodate 32", 36", 42" and 48" doors.These rails can be cut for smaller doors asspecified in the chart below.SARGENT will cut all rails to size if door width isspecified when the hardware is ordered.
Stock DoorSize Widths Remarks
Cover Dimensions andTouchbar Projections
Narrow Wide
Neutral Depressed
3"(77mm)
2-5/16"(59mm)
2-1/8"(54mm)
1-1/16"(27mm)
1-7/16"(37mm)
8-5/16"(211mm)
3"(76mm)
8-3/8"(213mm)
2-5/8"(67mm)
LP, LR & LS8600 Rail Sizes
80 Series Prefixes, Descriptions and Rail Sizes
1-800-727-5477 • www.sargentlock.com6409/05/08
Copyright©1998-2008,SargentM
anufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentM
anufacturingCompanyisprohibited.
How to Order Exit Devices12- 89 75 F ETMR 12VDV RHR 32D 36" 84" 41"
Prefixes Device Type Function Rail Size Trim Voltage HandFinish Finish Door
WidthOpeningHeight AFF
AvailablePrefixesListingPage 63
89 - Mortise 04 - NightLatch E 24"-32" For ET
trimspecify ETfollowedby Leverdesign,See pages46-48
ForThumbPiece
Trims andPulls
specify TrimDesignationas specifiedby DeviceType
12VDC
24VDC
Voltagerequiredfor
SolenoidControlledFunctions -70, 71,73, 74, 75& 76
RHR AvailableFinishespage 65
If doorwidthis
suppliedrailswill becut tosize
Requiredfor
VerticalRod ExitDevices
CenterLine ofRailAboveFinishFloor 41"Standard
WS89 - Mortise 06 - Nightlatch F 33"-36" LHR
88 - Rim 10 - Dummy J 37"-42"
HC88 - Rim 13 -Classroom G 43"-48"
WS88 - Rim 15 - PassageRail Sizes
Listed Beloware for LP, LR& LS Devices
Only
87 - SVR 16 -Entrance
NB87 - SVR 28 - TPPassage
HC87 - SVR 40 -FW Dummy
FM87 - SVR 43 - FWClassroom L 36" Door
MD86 - CVR 44 - FWNight Latch M 42"-44"
NB-MD86 - CVR 46 - FWNight Latch N 46"-48"
WD86 - CVR 62 - TPNight Latch
NB-WD86 - CVR 63 - TPClassroom
85 - Rim Narrow 66 - TPEntrance
84 - CVR Narrow
70 -SolenoidFail Safew/Cyl
NB-84 - CVRNarrow
71 -SolenoidFail Securew/Cyl
83 - MortiseNarrow
73 -SolenoidFail Safe
PP87 - CTL SVR74 -
SolenoidFail Secure
PR87 - CTL SVR
75 -SolenoidFail Safew/Cyl
SP87 - CTL SVR
76 -SolenoidFail Securew/Cyl
PP86 - CTL CVR
PR86 - CTL CVR
SP86 - CTL CVR
LP86 - CTL CVR
LR86 - CTL CVR
LS86 - CTL CVR
Door Opening Height
StopHeight
Door
1/4"(6mm)
Finished FloorLeft HandReverse “LHR”
Right HandReverse“RHR”
Inside
Outside
Mounting Heights• 41" (1041mm) from finished floor forstandard application
• 38" (965mm) from finished floor forelementary schools and to meet localaccessibility standards when a 100 or 300Series Auxiliary Control is used (38" AFFmust be specified)
1/8"(3mm)
Hand
How to order 700 Series ET TrimSpecify Function, Suffix, Lever, Finish and Handing (e.g., 713-8 ETL x 26D x RHR)Note: Suffix requirements are based on the type of exit device being used:• 700-8 is for 8800, 8500, NB8700, PP, PR & SP8700 devices, except with thesefunctions: 04, 10, 16, 40 & 44
• 700-6 is for all PP, PR, SP, LP, LR & LS8600 devices• 700-4 is for all WD & MD 8600 and 8400 devices• 700 with No Suffix for all 8900, 8300, 8700 with bottom rod and also for 8800,8500, NB8700, PP, PR & SP8700 devices with 04, 10, 16, 40 & 44 functions
LegendAFF - Above Finish Floor MD - Metal DoorCTL - Center & Top Latching Exit NB - No Bottom RodCVR - Concealed Vertical Rod SVR - Surface Vertical RodET - SARGENT External Lever Trim TP - Thumb Piece TrimFM - FEMA WD - Wood DoorFW - Freewheeling Trim WS - WindstormHC - Hurricane Code
80 Series How to Order
1-800-727-5477 • www.sargentlock.com 65 09/05/08
Copyright ©1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group com
pany. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
A. Exit devices shall be 80 Series push rail devices as manufactured by SARGENT Manufacturing Company, New Haven, CT.B. Exit devices shall be certified to meet or exceed the requirements of ANSI/BHMA A156.3 Grade 1.C. Exit devices shall be listed by Underwriters Laboratories for panic and bear the UL label for life safety in full compliance with NFPA 80
and NFPA 101. Exit devices for fire labeled doors shall be UL listed as “Fire Exit Hardware”.D. Provide standard hex key dogging on non fire-rated exit devices, with cylinder dogging (i.e., SARGENT 16- prefix) as an option.E. Exit devices shall comply with UL10C and UBC 7-2 positive pressure requirements.F. Construction:
1. Chassis shall be of heavy duty cast design with one piece drawn nonferrous removable covers matching the material of the push and mounting rails.2. Stamped steel chassis are not acceptable.3. Mounting rails shall be formed from a solid single piece of stainless steel, brass or bronze no less than 0.072 inches thick.4. Push rails shall be constructed of 0.062 inch thick material in the same manner as the mounting rail. Painted or anodized aluminum
shall not be considered heavy duty and are not acceptable.5. Provide protective Lexan touchpad on the exit device push rail to prevent scratches and serve as a visible guide to the user.6. Metal end caps shall be formed from the same base metal as the push and mounting rails.
G. Exit devices shall have a maximum of 3 inches projection from the face of the door in the non-dogged position. When in the dogged position, the device shall have no more than a 2-1/8 inch projection from the door face.
H. The design of the exit device shall eliminate the necessity of removing the device from the door for standard maintenance or keying changes.I. The device chassis shall be mounted and operable without the need of the rail or the chassis cover.J. Trim shall be through-bolted.K. Devices shall be available with matching trim for both wide and narrow stile doors, including electrified functions when required.L. Exit device operating lever trim shall withstand 1000 inch pounds of torque without allowing access.M. Lever trim shall be available in architectural finishes and designs to match that of the locksets specified.N. Exit devices shall have a five year limited warranty.The following guidelines should be referenced regularly and as required for proper appearance and longevity of finish.
2.01 EXIT DEVICES
*To avoid discoloration and pitting:• Keep stainless steel away from contact with other metals• Avoid cleaning with mineral acids or chlorine products• Avoid cleaning with abrasive products like sandpaper or steel wool
To maintain the finish:• Remove any contamination before damage occurs• Protect with a metal polish or car wax
CPC – Clear Powder CoatFor use in pool areas, offshore applications and highly corrosive applications, the clear powder coat eliminates need for cleaning and maintenance offinish. Applied over 32D only.
3 605 Bright brass, clear powder coat
Mild non-abrasive detergentwith damp cloth or sponge
Abrasive cleaners, bleach solvents,steel or bronze wool
4 606 Dull brass, clear powder coat
9 611 Bright bronze
10 612 Dull bronze, clear powder coat
10B 613 Antique bronze, oiled Lemon oil polished with dry cloth Abrasive cleaners, bleach solvents,steel or bronze wool
10BL – Oxidized satin bronze-lacquered
Mild non-abrasive detergentwith damp cloth or sponge
Abrasive cleaners, bleach solvents,steel or bronze wool
15 619 Satin nickel plate
20D – Statuary bronze, dark
26 625 Bright chrome
26D 626 Dull chrome
32 628 Bright stainless steel
32D 630 *Dull stainless steel Plastic pad or bronze wool Cleaners, solvents, bleach, steel wool
Finish
SARGENT# BHMA# Description How to clean Avoid these cleaners
80 Series Architectural Specifications, Finishes and Finish Care
1-800-727-5477 • www.sargentlock.com 11
8700 Functions & Trims80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.Description & Cylinder Info.
(1-3/4" Door)8700
Panic & Fire
8700Panic & Fire
ANSI Type 2OptionsDescription & Cylinder Info.
(1-3/4" Door)8700
Panic & Fire 8700
Mechanical Options:12-14-16-19-31-36-37-43-53-54-55-56-
56-HK-57-58-59-
BC-59-76-85-86-87-AL-BT-CPC-LD-PL-SG-TB-TL-
Cylinder Options:10-
10-21-10UL-10-63-11-
11-21-11-60-11-63-11-64-
11-70-7P-11-72-7P-11-73-7P-
11-65-73-7P-21-22-51-52-60-63-64-70-72-73-
65-73-65-73-7P-73-7P-81-82-
F1-82-83-
F1-83-84-BR-LC-SC-SE-
Freewheeling TrimThe lever rotates when the door islocked preventing excessive force frombeing applied to the horizontal lever
Electrified ET TrimVoltage must be specified for thefollowing functions: 73 and 74.Specify: 12VDC or 24VDC
Description & CylinderInfo. (1-3/4" Door)
AvailableFinishes
SARGENTFinishes
ANSIFinishes
0304091010B10BL141520D2626D3232D
605606611612613614618619624625626629630
700 Series ET TrimExits with ET Trim, specifylever design after the ETdesignation (e.g., ETL)
Options Series Function Rail Lgth Trim Hand Outside Finish Inside Finish Door Width Door Height AFFF1-83- 87 13 F ETL RHR 32D 10B 36" 84" 41"
06 09Key unlocks Trim, Trim retracts latch/Trim relocks when key is removed
#41 Cylinder Supplied8706 x ET_
10 01 No outside operation (No Cylinder)** 8710
10 02 No outside operation (No Cylinder)**ET Control is used as Pull Only 8710 x ET_
13 08 Key Outside Unlocks/locks Trim#41 Cylinder Supplied 8713 x ET_
15 14 Passage Only (No cylinder) 8715 x ET_
40 02 Freewheeling Trim -No outside Operation (No Cylinder)** Dummy Trim 8740 x ET_
43 08Freewheeling Trim -
Key Outside Unlocks/locks Trim#41 Cylinder Supplied
8743 x ET_
46 09Freewheeling Trim -
Key unlocks Trim, Trim retracts latch/relocks when key is removed #41 Cylinder Supplied
8746 x ET_
73 Electrified ET Trim - Fail SafePower Off, Unlocks Lever (No Cylinder)** 8773 x ET_
74 Electrified ET Trim - Fail SecurePower Off, Locks Lever (No Cylinder)** 8774 x ET_
10 02 Pull Only(No Cylinder)*** 810-FLL 810-FLW 810-MAL 810-PTB 810-STS 8710 x Trim
Designation
28 15 Passage Only(No cylinder) 828-FLL 828-FLW 828-MAL 828-PTB 828-STS 8728 x Trim
Designation
62 06Key unlocks Trim, Trim retracts latch/Trim relocks when key is removed
#34 Cylinder Supplied866-FLL 866-FLW 866-MAL 866-PTB 866-STS 8762 x Trim
Designation
63 05 Key Outside Unlocks/locks Trim #34 Cylinder Supplied 866-FLL 866-FLW 866-MAL 866-PTB 866-STS 8763 x Trim
Designation
06 12Key unlocks Turn; Turn retracts latch/Turn relocks when key is removed
#41 Cylinder Supplied8710 x 306
10 02 862 Pull Only(Optional Pulls: 863 & 864) 8710 x 862
13 11 Key Outside Unlocks/locks Turn#41 Cylinder Supplied 8710 x 313862 Pull
SARGENTFunctionNumbers
ANSIFunctionNumbers
SARGENTFunctionNumbers
300 Series++Auxiliary Control & 862 Pull
ANSIFunctionNumbers
SARGENTFunctionNumbers
ANSIFunctionNumbers
300 SeriesAux. Control
How to order:
Note: Exit devices are available in all standard finishes, except 14, 15, 26 & 26D. With these finishes, exit devices are supplied in 32or 32D tomatch accordingly. 26 or 26D is automatically supplied when 32 or 32D is specified. For nickel finishes, specify 14/32 or15/32D to receive nickel finished trims and stainless exit devices.Note: AFF means Above Finished Floor, center line of rail Above Finished Floor** Cylinder Override is available with a 306 Aux ControlExample Order: 8773F 12V x ETMG x 306 x RHR x 32D x 36"w x 84"h
*** Cylinder Override is available with a 306 Aux ControlNote: Thumb piece trims for 62 and 63 function devices are identical and are identified as 66 function when trim is ordered separately.Note: FLW trim is not available in 32(629) or 32D(630)
Pull & Thumb Piece Trim Section
ET Designation with Suffix(Used to order ET without device)
8700 Series: 706, 710, 713, 715, 740,743, 744, 746, 773 & 774
Lever Designs for ET ControlsA, B, E, F, J, L, P, WAlso available with Coastal Series &Studio Collection Levers
Note: When ordering 8700 Series Exit Device x 300 Series Aux. Control, specify 10 Function for the exit. Example: 8710F x 306 x RHR x 32D x 42" x 90"++ Note: Exit Devices must be mounted 38" AFF when used with a 300 Series Auxiliary Controls to meet ICC/ANSI A117.1-2003 Accessible & Usable Buildings and Facilities Code
Trim Designations• Use three letter designations (Ex “PTB”) when ordering theExit Device with trim
• Use the six digit designation (Ex “866-MAL”) when orderingtrim without an Exit Device, always specify finish
1-800-727-5477 • www.sargentlock.com62
ET Trim, Levers and Pulls80 Series
W Lever
J Lever*
Pulls
F LeverE Lever
P Lever*L Lever*
A Lever B LeverET Lever Controls
*Projection varies by lever design.2-1/2" (63mm) projection withL Lever
* Lever returns within 1/2" (13mm) of door face
• Handed
3-1/8"(79mm)
13/16"(21mm)
4-5/8"(117mm)
13/16"(21mm)
4-1/2"(114mm)
1/2"(13mm)
863 864862
10"(254mm)MTGHoles
4"(102mm)
18"(457mm)MTGHoles
4"(102mm)
10"(254mm)MTG Holes
3-1/2"(89mm)
3/4" Dia.(19mm)
1" Dia.(25mm)
1" Dia.(25mm)
13/16"(21mm)
1-13/16"(46mm)
8-1/16"(205mm)
3-9/16" MAX*(90mm)
3-1/2"(89mm)
13/16"(21mm)
4-1/2"(114mm)
13/16"(21mm)
4"(102mm)
3-1/4"(83mm)3"
(76mm)
4"(102mm)
13/16"(21mm)
1/2"(13mm)2-3/4"
(70mm)
13/16"(21mm)
4-11/16"(119mm)
3"(76mm)
13/16"(21mm)
5/16"(8mm)
4-15/16"(125mm)
90°
1-3/4"(44mm)
2-3/4"(70mm)
3"(76mm)
13/16"(21mm)
4-11/16"(119mm)
2-3/8"(60mm)
SIDE PROFILE
Note: ET suffixes required when ordering ETtrim without an exit device, see page 71 forcomplete details
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
1-800-727-5477 • www.sargentlock.com 63
Coastal Series Levers &Thumb Piece Pulls80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
• Specify hand when ordering• Specify hand when ordering • Specify hand when ordering
C* - Coronado™ R - Rockport™
Y - Yarmouth™ G - Gulfport™ S - Sanibel™
2-1/2"(64mm)
13/16"(21mm)
4-1/4"(108mm)
3-1/4"(83mm)
13/16"(21mm)
4-1/2"(114mm)
3-1/2"(89mm)
13/16"(21mm)
4-1/2"(114mm)
4-1/16"(103mm)
13/16"(21mm)
4-1/2"(114mm)
2-3/4"(70mm)
13/16"(21mm)
4-3/4"(121mm)
PTB/PSB
MAL/MSL
STS
FLW/FSWFLL/FSL1-3/4"
(44mm)2-1/16"(52mm)
6"(152mm)
14-5/16"(364mm)
1-3/4"(44mm)
14-5/16"(364mm)
2-1/16"(52mm)
6"(152mm)
2-1/16"(52mm)
2-5/8"(67mm)
14-1/4"(362mm)
6"152mm
802-PTB
2-1/16"(52mm)
3-1/2"(98mm)
15"(381mm)
6"152mm
6"(152mm)
3-1/2"(89mm)
1-15/16"(49mm)
15"(381mm)
1-5/8"(41mm)
2-1/4"(57mm)
7-3/16"(198mm)
9-5/8"(244mm)
• Coastal Series™ levers can be usedwithall SARGENT 80 Series exit devices with ET trim
• All levers – solid cast brass• All standard functions available• Finishes available: 03, 04, 09, 10, 10B, 10BL,14, 15, 20D, 26, 26D
* Lever returns within 1/2" (13mm) of door face
Pulls and Thumb Pieces TrimsThese trims are through-bolted, creating perfect alignment of center case, thumb piece and cylinder, as required. Through-bolts pass through thechassis of the devices and are bolted directly to the trim. FSL, FSW, MSL and PSB pulls are used with 12- 8804 and 8804 only, they are identical to FLL,FLW, MAL and PTB pulls except the cylinder hole is located 3/8" (9mm) lower. The 802-PTB plate is a flat plate which can be used to cover existing doorpreps and is as ANSI/BHMA function 01.
1-800-727-5477 • www.sargentlock.com64
Studio Collection Levers80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
Features• Studio Collection levers can be used with all SARGENT 80 Series exit devices with ET trim• All levers - solid brass or stainless steel• Available with all lever functions• Lever finishes available: 03, 04, 09, 10, 10B, 10BL, 14, 15, 20D, 26, 26D, 32 & 32D• Always specify hand
MO
ML
MZ*
MA
MC
MD
MJ
MP
ND*
NJ*
MQ
MR
MT
MM
MY*
MB
ME
MF
MG
MI
MW*
MN
MH
MK
MS
MU
MV
MX*
NS*
NU*
RCM**
RAL**
REM**
RAM**
RAS**
RAW**
Rialto Series
Odéon Series
Aventura Series
Centro Series
Notting Hill Series
* Lever returns within 1/2" (13mm) of door face ** The Gramercy Levers are customized. Refer topage 65 on how to order
Gramercy Series
Gramercy Lever information
1-800-727-5477 • www.sargentlock.com 65
Ordering GramercySeries Levers80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
Elements of Gramercy Series Leversgrip grip
shankshankshank
insert
REM RCM RAM, RAW, RAS, RAL
Lever Part Number Shank Finish* Insert Grip Finish
Plain† REM Polish Stainless (629) orSatin Stainless (630) n/a Polish Stainless (629) or
Satin Stainless (630)
With Raised Band RCM Polished Stainless (629) n/a Polish Stainless (629) orSatin Stainless (630)
With Metallic Insert RAM Polished Stainless (629) Satin Stainless(630) Polished Stainless (629)
WithWood Insert† RAW Polished Stainless (629) orSatin Stainless (630) Birch (BH) Polish Stainless (629) or
Satin Stainless (630)
With Santoprenne Insert† RAS Polished Stainless (629) orSatin Stainless (630) Black (BK) Polish Stainless (629) or
Satin Stainless (630)
With Leather Insert† RAL Polished Stainless (629) orSatin Stainless (630)
Black (BK) orBrown (BN)
Polish Stainless (629) orSatin Stainless (630)
* Rose and escutcheon finish is designated by shank finish selected† Grip finish must match shank finish
* Escutcheon finish is designated by shank finish selected
To order Gramercy Series levers with 80 Series products, see the example below. When specifying finish, use the last two digits of the BHMA standardfinish code, i.e. use “29” for polished stainless, BHMA finish 629.
Options Series Function RailSize Voltage Trim Lever Shank
Finish*InsertFinish
GripFinish Hand Inside
FinishDoorWidth
OpeningHeight AFF
Select from 80 Series catalog
Specifiedfor
electricalfunctions
Selectfrom80
Seriescatalog
Leatherinsert
Polishedor satinstainless
Black orbrown
Polishedor satinstainless
RHRRH,
LHR, orLH
Selectfrom
80 Seriescatalog
Forverticalrod
devices
AboveFinishedFloor
10- 87 73 F 12VDC F RAL 29 BN 29 RH 32D 36" 84" 41"
Sample order on how to specify anExit Device with Gramercy levers
1-800-727-5477 • www.sargentlock.com66
Anti-Vandal Trim, 988 Surface Bolt,ET Plates & Dummy Rails80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
8893 Dummy Rail
A decorative push bar for vestibule doorapplications where continuity of design isdesired, but no exit device is required.Outside dummy trim available on order.
• Order as a: 8893 x finish; Specify door widthand door stile width when ordering.
8895 Active Dummy Rail
Push rail operates on this rail to simulateactive doors. Can be used with dummy trim.
• Order as a: 8885 x Finish; specify door widthand door stile width when ordering.
• Available with Request-to-Exit (REX) signalingswitch; specify 55-8895 x Finish
ET Cover Plate
This plate is designed to bemountedbehind the ET control to cover a stockhollowmetal cutout• Order as a: 68-0657 x finish
3-1/2"(89mm)
8-3/4"(222mm)
• Lexan touchpad replacement kit forall 80 Series push rails
• Direct replacement – uses existingmounting holes
• Order as a: 809 Touch Pad
809 Touchpad Kit
For all ET functions
Designed for exterior doors that requireextra security or resistance to vandalism,anti-vandal trim (AVT) plates have anextended lip on the active side of the doorto provide extra protection for thelatchbolt. A matte plastic coated gripprovides a comfortable pull over widetemperature ranges. Fully through-boltedwith no exposed exterior fasteners for acleaner look and increased security.
3-1/8"(79mm)
10-9/16"(268mm)
8-3/16"(208mm)
3-9/16"(90mm)
1-1/4" Dia.(32mm)
Anti-Vandal Trim
• Designed for severewindload (HurricaneCode) environmentswhere surface boltsare required (e.g., on inactive doors)
• Tested to Dade County protocols• Listed to UL 10C for use on fire rated
door assemblies. Refer to codes forlocations where surface bolts are allowedon fire doors
• All steel construction for maximumstrength and heavy duty use– Full 3/4" (19mm) square, 12" (305mm)
bolt with 1-1/4" (32mm) throw– Bright zinc-plated finish– Jimmy-resistant design locks bolt
automatically when thrown; releasedby pressing knob toward door whileretracting
– Bolt can be locked in retracted orthrown position
• Angle (L shaped) andmortise strike withmounting hardware supplied standard
• Order as a: 988 Surface Bolt
988 Surface Bolt Kit
Features• Heavy duty 12 gauge stainless steel in 32D finish• Through-bolted for added strength• Handed – Specify RHR or LHR• ADA Compliant• #34 Rim Cylinder supplied for 8804• #41 Mortise Cylinder supplied for 8904• Night Latch and Dummy Functions available• Available for MD &WD8610, 8710, 8804, 8810,8904 & 8910 Devices
•Without protective lip for inactive door• AVT Retrofit Kit works easily with existing productwith minor prep modification
• Order by part number (826, 824, 821 or 827) asdetermined by product & function below
Part Number Description Application
826 Cylinder, but NoProtective Lip 8804 Mfg after 02-2001
824 Protective Lip &Cylinder
8904; also 8804 Mfgbefore 02-2001
821 No Protective Lip& No Cylinder
MD &WD8610, 8710and 8810
827 Protective Lip &No Cylinder 8910
821 for use on all inactive leafs
09/05/08
Copyright©1998-2008,SargentM
anufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentM
anufacturingCompanyisprohibited.
• This revolutionary finish coating available on all SARGENT product lines, utilizes asilver-based antimicrobial compound from Agion® Technologies
• The MicroShield protection is now available integrated within the 80 Series touchpad as well as the finish coating. MicroShield lasts for the life of the finish
• MicroShield coating permanently suppresses the growth of bacteria, algae, fungus,mold and mildew. It is effective against a broad spectrum of bacteria
• Non-toxic and completely safe. The Agion antimicrobial compound is EPA and NSFapproved and FDA listed for use in medical and food preparation equipment
• Applications: Anywhere there is need for a clean environment (hospitals,laboratories, schools, medical centers, daycare, food processing etc.)
1-800-727-5477 • www.sargentlock.com2
80 Series 80 Series Exit DevicesFeatures
Strength & Durability• Made of finest component materials• Heavy duty mounting construction• Built to withstand abusive conditions• Available options to meet Dade County Protocols and other localhurricane code requirements for highwind load andmissile impact*
• 5 Year warranty* Consult factory
SARGENT manufactures a full line of exit devices including vertical rod, rim and mortise devices for both standard and narrow stile doors. Thesedevices provide the best combination of simplicity, strength, durability, aesthetics and innovation and are perfect for applications in commercial officebuildings, medical and educational institutions.
Innovation• SARGENT introduces Beacon™, a next generation exit device thatcreates a clearer pathway to safety during an emergency. Thecombination of audible and visible alerts built into the exit devicemakes Beacon unique – and effective.
• Broad offering of electro-mechanical solutions for the mostdemanding access/egress control applications
• MicroShield™ anti-microbial finish coating offers a new levelof protection
• SARGuide™ exit device contains an electroluminescent touchpad toenhance the visibility of exit locations in dark or smoke-filled passagesand effectively improve the safety of any public building
• CTL (Center and Top Latching) Vertical Rod Devices offer less bottomrod convenience with true center latching for added security
Security• Double cylinder functions available• Torx® and spanner screws• Anti-vandal trim options• Master keying with SARGENT Security Key systems available(V-10, Signature, Keso F1, Keso and XC)
Microshield™ Coating
• The SARGuide illuminated exit device increases visibility of exitlocations in dark or smoke-filled passages, supplementing existingcodes for egress lighting
• SARGuide utilizes state-of-the-art FLATLITE electroluminescent lightingfrom E-Lite Technologies Inc.
• Green-blue electroluminescent light provides 3 to 5 times the visibilityof other lights
• Can be wired for continuous operation or activation by fire alarm system• Exit devices are placed low enough on a door to provide an extendedwindow of opportunity for safe emergency egress
• Supplements building exit signs required by code• Intuitive operation. Integral “EXIT” signage guides users directly to themeans of egress
• UL Listed for use on panic (UL 305) and fire-rated (UL10C) exit devices• Available with mechanical, and many electro-mechanical, exit devices• See pages 56 & 57 for information on the TL- & PL- offerings
Simplicity• Easy installation!• Maintenance-free design• Few moving parts – less wear• Modular construction• Rekeying is accomplished without removing device from door
Aesthetics• Clean, simple, aesthetically pleasing design• “True” architectural hardware finishes consistent with BHMA/ANSIstandards
• Coastal Series and Studio Collection Levers adds a touch of elegance
MicroShield™As part of their promise to provide innovative solutions to their customers,ASSA ABLOY Group companies offer the MicroShieldTM technology, a silver-basedantimicrobial coating designed to stem the spread of germs and bacteria.
MicroShieldTM is a trademark of Yale Security Inc., an ASSA ABLOY Group company.
The Agion antimicrobial is not intended as a substitute for good hygiene.Coated products must still be cleaned to insure the surfaces will be free ofdestructive microbes. ASSA ABLOY makes no representations or warranties,express or implied, as to the efficacy of the Agion antimicrobial. A copy ofthe Agion warranty is available upon request.Agion is a registered trademark of Agion Technologies, Inc., Wakefield, MA, USA
09/05/08
Copyright©1998-2008,SargentM
anufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentM
anufacturingCompanyisprohibited.
1-800-727-5477 • www.sargentlock.com 3
80 Series 80 Series Exit DevicesUL Fire Door Ratings andOpenings Sizes
Maximum Door Opening-Fire Doors
Exit Device DoorMaterial Single Door
Double Door Applications
with12-HC980 or12-980 or12-L980 or12-HCL980Mullion
with12-HD980Mullion
VR/VRDoors Swing
SameDirection
SVR/MortiseDoors Swing
SameDirection
CVR/MortiseMD DoorsSwing SameDirection
CVR/MortiseWD DoorsSwing SameDirection
VR/VRDouble Egress
12-8800 Metal 3 Hour 4' x 10' 3 Hour 8' x 8' 3 Hour 8' x 10' –– –– –– –– ––
12-8800 Wood 3 Hour 4' x 10' 3 Hour 8' x 8' 3 Hour 8' x 10' –– –– –– –– ––
12-8900 Metal 3 Hour 4' x 10' –– –– –– 3 Hour 8' x 8' 3 Hour 8' x 10' –– ––
12-8900 Wood 3 Hour 4' x 10' –– –– –– 3 Hour 8' x 8' –– 3 Hour 8' x 9' ––
12-8300 Metal 3 Hour 4' x 10' –– –– –– –– 3 Hour 8' x 10' –– ––
12-8300 Wood 3 Hour 4' x 10' –– –– –– –– –– 3 Hour 8' x 9' ––
12-FM8700 Metal 3 Hour 4' x 7' –– –– 3 Hour 6' x 7' –– –– –– ––
12-8700 Metal –– –– –– 3 Hour 8' x 8' 3 Hour 8' x 8' –– –– 3 Hour 8' x 8'
12-8700 Wood –– –– –– 3 Hour 8' x 8' 3 Hour 8' x 8' –– –– 3 Hour 8' x 8'
12-NB8700 Metal –– –– –– 3 Hour 8' x 8' –– –– –– 3 Hour 8' x 8'
12-NB8700 Wood –– –– –– 3 Hour 8' x 8' –– –– –– 3 Hour 8' x 8'
12-SP8700 Metal 90Min 4' x 10' –– –– –– –– –– –– ––
12-SP8700 Wood 90Min 4' x 9' –– –– –– –– –– –– ––
12-PP8700 &12-PR8700 Metal –– –– –– 3 Hour 8' x 10' –– –– –– 3 Hour 8' x 10'
12-PP8700 &12-PR8700 Wood –– –– –– 3 Hour 8' x 8' –– –– –– 3 Hour 8' x 8'
12-MD8600 Metal –– –– –– 3 Hour 8' x 10' –– 3 Hour 8' x 10' –– 3 Hour 8' x 10'
12-NB-MD8600 Metal –– –– –– 3 Hour 8' x 10' –– –– –– 3 Hour 8' x 10'
12-WD8600 Wood –– –– –– 90Min 8' x 9' –– –– 3 Hour 8' x 9' 3 Hour 8' x 9'
12-NB-WD8600 Wood –– –– –– 90Min 8' x 9' –– –– –– 3 Hour 8' x 9'
12-MD8400 Metal –– –– –– 3 Hour 8' x 10' –– 3 Hour 8' x 10' –– 3 Hour 8' x 10'
12-NB-MD8400 Metal –– –– –– 3 Hour 8' x 10' –– –– –– 3 Hour 8' x 10'
12-SP8600 Metal 3 Hour 4' x 10' –– –– –– –– –– –– ––
12-SP8600 Wood 45Min 4' x 9' –– –– –– –– –– –– ––
12-PP8600 &12-PR8600 Metal –– –– –– 3 Hour 8' x 10' –– –– –– 3 Hour 8' x 10'
12-PP8600 &12- PR8600 Wood –– –– –– 90Min 8' x 8' –– –– –– 45Min 8' x 8'
12-LS8600 Metal 3 Hour 4' x 10' –– –– –– –– –– ––
12-LP8600 &12-LR8600 Metal –– –– –– 3 Hour 8' x 10' –– –– –– 3 Hour 8' x 10'
CVR/Mortise
CVR
SVR/Mortise
SVR
MortiseLock
Rim
Type
09/05/08
Copyright©1998-2008,SargentM
anufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentM
anufacturingCompanyisprohibited.
1-800-727-5477 • www.sargentlock.com6
80 Series 8800 Rim Exit Device
649 Strike• Surface applied• Panic & Fire Rated• Black nylon coated
688 Trim Retrofit Kit
Specifications 8800 Series Rim Exit Device
8800 Features• Designed for standard width stile applicationson wood and metal doors
• Most functions are non-handed• Single point rim latching device• Single door & double door applications withmullions
• Quiet operation and solid security• Devices are ANSI A156.3 – 2001 Grade 1• UL Fire and Panic listed
8800 SeriesRim Exit Device
Door Types Wood or metal 1 3/4" (44 mm) minimum thickness. For doors over1-3/4" to 2-1/4" thick, specify thickness and order as 31- prefix
Door Widths E Rail - 24" to 32" (61cm to 81cm) No cutting required for 32" doorF Rail - 33" to 36" (84cm to 91cm) No cutting required for 36" doorJ Rail - 37" to 42" (94cm to 107cm) No cutting required for 42" doorG Rail - 43" to 48" (110cm to 122cm) No cutting required for 48" door
Strike 649 Standard Black Nylon CoatedOptional Strikes 642, 644 and 613Dogging Feature Hex key dogging standard; Cylinder dogging available (16-)Electric Options AL- Alarmed Exit Device - Page 56
BT- Beacon™ Exit Device - Page 55PL- SARGuide Photoluminescent Coated Push Rail - Page 56TL- SARGuide Illuminated Touchpad - Page 5753- LX Latchbolt Monitor Switch - Page 5754- Outside Lever Monitoring - Page 6255- Request-to-Exit Signal - Rail Monitoring - Page 5756- ELR Remote Latch Retraction - Page 5857- Delay Egress Exit to be used in conjunction with Electromagnet - Page 6058- Electric Dogging - Page 6159- Electroguard – Self Contained Delayed Egress Device - Page 61
Mounting Fasteners Supplied standard with wood and machine screwsAvailable with through-bolts and mortise (sex) nuts
Latch Bolt Stainless steel, 3/4" (19mm) throwDevice Centerline from 41” (1041 mm) for Standard ApplicationsFinished FloorCenter Case Dimensions 8-3/8" (213mm) x 2-5/8" (67mm)Projection Pushbar Neutral – 3" (76 mm)
Pushbar Depressed – 2-1/8" (54 mm)Fire Exit Hardware See Chart – Page 3
• Mortised. Dimension “L”equals door thickness plus1/2" (13mm). Black nyloncoated on lip only.
Alternate Strikes For 8800 Rim Devices
• Half mortised.Black nylon coated.
• Surface applied. For useon pairs of doors withoutmullion. Ductile Iron.Black nylon coated.
1/4"(6mm)
1-1/2"(38mm)
5/8"(16mm)
3-5/8"(92mm)
1-1/2"(38mm)
3-5/8"(92mm)
1-1/2"(38mm)
“L”
7/16"(38mm)
2"(92mm)
2-7/16"(62mm)
613 Strike642 Strike 644 Strike• A SARGENT 8800/8888 RimExit x ET with a 688 TrimRetrofit Kit will easily replaceVonDuprin's 98/99 SeriesExit with no additional doorprep.Note: 688 Trim Kit onlyrequiredwhen replacing VonDuprin trim.
1-800-727-5477 • www.sargentlock.com 63 09/05/08
Copyright©1998-2008,SargentM
anufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentM
anufacturingCompanyisprohibited.
L Rail 36" (91cm) No cuttingrequired
M Rail 42" to 44" No cutting(107cm to 112cm) required
N Rail 46" to 48" No cutting(117cm to 122cm) required
10 Signature System10-UL Signature, meets UL437 cylinder+11 SARGENT XC Key System12 UL Fire Label Exit Devices14 Sliding bolt bottom case for 8700++16 Cylinder lockdown feature19 Pushbar without Lexan touchpad21 Construction Keying Conventional, XC
and Signature Series22 Construction Keying Conventional
Cylinders (Existing Systems Only)23 ANSI flat lip strike (8300, 8900,
including 12- Prefix)*31 Doors over 1-3/4" and/or Panels36 6 Lobe security head screws37 Spanner head screws43 Flush End Cap*53 Latchbolt monitoring switch54 Internal micro switch in ET Control55 Signal Switch in Rail (Request to Exit)56 Remote Dogging/Latch Retraction56-HK Remote Latch Retraction with manual Hex
Key dogging57 DelayedEgress (Magnetorderedseparately)58 Electric Dogging**59 Electroguard® Self Contained Delayed
Egress Device**BC59 Electroguard Boca Code (Door Status Switch
required)60 Disposable Construction Core63 SARGENT Removable Core cyl. Includes
masterkeying, grand masterkeying64 SARGENT Removable Construction Core
cylinder65-73 6 Pin Uncombinated Small Format
Interchangeable Cores65-73-7P 7 Pin Uncombinated Small Format
Interchangeable Type Cores70 Exit device to accept Small Format
Interchangeable Cores - no core provided72 Exit device to accept Small Format
Interchangeable Cores with ConstructionCore provided
73 Small Format 6-Pin interchangeable core(refer to CK-8 for available keyways)
73-7P Small Format 7-pin interchangeable core,(refer to CK-8 for available keyways)
75 Warning inside, Abrasive strip on rail76 Knurled Outside Lever77 Warning inside and outside, abrasive strip
on rail, abrasive coating on Lever81 Cylinder to accept Keso (83) and Keso F1
(F183) removable core – no core providedF1-82 Keso Security Cylinder with Front
Profile (Patent Pending)82 Keso Security CylinderF1-83 Keso Security Removable Core Cylinder
with Front Profile (Patent Pending)83 KesoSecurityRemovableCoreCylinder84 Keso Security Removable Construction
Core CylinderAL Alarmed ExitBR Bump Resistant Cylinder (Available with
Conventional & XC Cylinders Only)***BT Beacon- Emergency Audio & Visual egress
system with a self contained Laser, FlashingLEDs & Audio alert
GL Guarded Latchbolt for 8800NB No Bottom Rod (Not available with 59- &
BC59- )PL SARGuide™ PL – Photoluminescent Coated
Push Rail – (Touchpad eliminated)SC, SE Exit Device furnished in Schlage C or E
Keyway (specify)SG MicroShield - Antimicrobial clear powder coatTL SARGuide Illuminated touchpadVA, VC, SARGENT V-10 CylindersVS, VC, VS See V-10 Cylinder Section
Cylinder Notes:• 16- Cylinder Dogging uses a 41 insidecylinder with 97 ring
• Removable core and 70 prefix cylindersrequire a 97-0351 cylinder rings for 700Series ET Controls and 94-0153 ring for 100 &300 Series Aux controls
• Less cylinder - SARGENT supplies standardblocking rings. Specify if using competitorcylinders
• When ordering BEST cylinders for use inSARGENT Exit Devices, use the following BESTproduct numbers:Mortise cylinder: 1-E74XC208Rim cylinder: 1ESPL-7-AO5994
Notes For Prefixes• 31- Specify door thickness and specify panelthickness and location, if used
• 31- prefix not available, HC8700, FM8700,PP, PR & SP8700, PP, PR & SP8600, LP, LR &LP8700,
• 31- Prefix requires extended lip strike for8300 & 8900 Series (supplied).
• SC- Prefix not available in 57- Prefix,(SC- Cylinders are only available in 41 lengthcylinders and Rim cylinders)
• SC-, SE- & VC- Prefixes not available with thefollowing: 8904, 8916, 8944, 8975, 8976,8866, 8304, 8344, 8375 & 8376 (SC- & SE-#41 cylinders only & VC- #42 cylinders only)
+ 11- Prefix not available with 10-, 10-UL-, 22-,60-, 63-, 64- SE, SC, 82-, F1-82-, 82-, F1-83- &84- prefixes.
++16- Prefix not available with 12-, 57, 59- orAL- prefix
* 53- Not available on PP/PR/SP8600 &LP/LR/LS8600 Exit Devices** 59- & BC59- are not available with 16-, 55-,56-, 57-, 58- prefixes and on NB8700,PP/PR/SP8600 & LP/LR/LS8600 Exit Devices
*** BT- Not available FM8700 Devices & thesesprefixes 16-, 56-, 57-, 59-, BC59- and AL
SuffixCPC Clear Powder Coat – Recommended forexit devices used in full exterior application andhighly corrosive areas with 32 and 32D finishes.How to order: 8313F x ETL x 32D x CPC
Note: For additional information on ElectrifiedExit Devices, see the Electrified Exit Devicecatalog at www.sargentlock.com
Prefixes Available
E 24" to 32" No cutting required(61cm to 81cm) for 32"(81cm) door
F 33"to 36" No cutting required(84cm to 91cm) for 36" (91cm) door
J 37" to 42" No cutting required(94cm to 107cm) for 42" (107cm) door
G 43" to 48" No cutting required(110cmto122cm) for 48" (122cm) door
Rail SizesSARGENT offers four sizes of rails toaccommodate 32", 36", 42" and 48" doors.These rails can be cut for smaller doors asspecified in the chart below.SARGENT will cut all rails to size if door width isspecified when the hardware is ordered.
Stock DoorSize Widths Remarks
Cover Dimensions andTouchbar Projections
Narrow Wide
Neutral Depressed
3"(77mm)
2-5/16"(59mm)
2-1/8"(54mm)
1-1/16"(27mm)
1-7/16"(37mm)
8-5/16"(211mm)
3"(76mm)
8-3/8"(213mm)
2-5/8"(67mm)
LP, LR & LS8600 Rail Sizes
80 Series Prefixes, Descriptions and Rail Sizes
1-800-727-5477 • www.sargentlock.com6409/05/08
Copyright©1998-2008,SargentM
anufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentM
anufacturingCompanyisprohibited.
How to Order Exit Devices12- 89 75 F ETMR 12VDV RHR 32D 36" 84" 41"
Prefixes Device Type Function Rail Size Trim Voltage HandFinish Finish Door
WidthOpeningHeight AFF
AvailablePrefixesListingPage 63
89 - Mortise 04 - NightLatch E 24"-32" For ET
trimspecify ETfollowedby Leverdesign,See pages46-48
ForThumbPiece
Trims andPulls
specify TrimDesignationas specifiedby DeviceType
12VDC
24VDC
Voltagerequiredfor
SolenoidControlledFunctions -70, 71,73, 74, 75& 76
RHR AvailableFinishespage 65
If doorwidthis
suppliedrailswill becut tosize
Requiredfor
VerticalRod ExitDevices
CenterLine ofRailAboveFinishFloor 41"Standard
WS89 - Mortise 06 - Nightlatch F 33"-36" LHR
88 - Rim 10 - Dummy J 37"-42"
HC88 - Rim 13 -Classroom G 43"-48"
WS88 - Rim 15 - PassageRail Sizes
Listed Beloware for LP, LR& LS Devices
Only
87 - SVR 16 -Entrance
NB87 - SVR 28 - TPPassage
HC87 - SVR 40 -FW Dummy
FM87 - SVR 43 - FWClassroom L 36" Door
MD86 - CVR 44 - FWNight Latch M 42"-44"
NB-MD86 - CVR 46 - FWNight Latch N 46"-48"
WD86 - CVR 62 - TPNight Latch
NB-WD86 - CVR 63 - TPClassroom
85 - Rim Narrow 66 - TPEntrance
84 - CVR Narrow
70 -SolenoidFail Safew/Cyl
NB-84 - CVRNarrow
71 -SolenoidFail Securew/Cyl
83 - MortiseNarrow
73 -SolenoidFail Safe
PP87 - CTL SVR74 -
SolenoidFail Secure
PR87 - CTL SVR
75 -SolenoidFail Safew/Cyl
SP87 - CTL SVR
76 -SolenoidFail Securew/Cyl
PP86 - CTL CVR
PR86 - CTL CVR
SP86 - CTL CVR
LP86 - CTL CVR
LR86 - CTL CVR
LS86 - CTL CVR
Door Opening Height
StopHeight
Door
1/4"(6mm)
Finished FloorLeft HandReverse “LHR”
Right HandReverse“RHR”
Inside
Outside
Mounting Heights• 41" (1041mm) from finished floor forstandard application
• 38" (965mm) from finished floor forelementary schools and to meet localaccessibility standards when a 100 or 300Series Auxiliary Control is used (38" AFFmust be specified)
1/8"(3mm)
Hand
How to order 700 Series ET TrimSpecify Function, Suffix, Lever, Finish and Handing (e.g., 713-8 ETL x 26D x RHR)Note: Suffix requirements are based on the type of exit device being used:• 700-8 is for 8800, 8500, NB8700, PP, PR & SP8700 devices, except with thesefunctions: 04, 10, 16, 40 & 44
• 700-6 is for all PP, PR, SP, LP, LR & LS8600 devices• 700-4 is for all WD & MD 8600 and 8400 devices• 700 with No Suffix for all 8900, 8300, 8700 with bottom rod and also for 8800,8500, NB8700, PP, PR & SP8700 devices with 04, 10, 16, 40 & 44 functions
LegendAFF - Above Finish Floor MD - Metal DoorCTL - Center & Top Latching Exit NB - No Bottom RodCVR - Concealed Vertical Rod SVR - Surface Vertical RodET - SARGENT External Lever Trim TP - Thumb Piece TrimFM - FEMA WD - Wood DoorFW - Freewheeling Trim WS - WindstormHC - Hurricane Code
80 Series How to Order
1-800-727-5477 • www.sargentlock.com 65 09/05/08
Copyright ©1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group com
pany. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
A. Exit devices shall be 80 Series push rail devices as manufactured by SARGENT Manufacturing Company, New Haven, CT.B. Exit devices shall be certified to meet or exceed the requirements of ANSI/BHMA A156.3 Grade 1.C. Exit devices shall be listed by Underwriters Laboratories for panic and bear the UL label for life safety in full compliance with NFPA 80
and NFPA 101. Exit devices for fire labeled doors shall be UL listed as “Fire Exit Hardware”.D. Provide standard hex key dogging on non fire-rated exit devices, with cylinder dogging (i.e., SARGENT 16- prefix) as an option.E. Exit devices shall comply with UL10C and UBC 7-2 positive pressure requirements.F. Construction:
1. Chassis shall be of heavy duty cast design with one piece drawn nonferrous removable covers matching the material of the push and mounting rails.2. Stamped steel chassis are not acceptable.3. Mounting rails shall be formed from a solid single piece of stainless steel, brass or bronze no less than 0.072 inches thick.4. Push rails shall be constructed of 0.062 inch thick material in the same manner as the mounting rail. Painted or anodized aluminum
shall not be considered heavy duty and are not acceptable.5. Provide protective Lexan touchpad on the exit device push rail to prevent scratches and serve as a visible guide to the user.6. Metal end caps shall be formed from the same base metal as the push and mounting rails.
G. Exit devices shall have a maximum of 3 inches projection from the face of the door in the non-dogged position. When in the dogged position, the device shall have no more than a 2-1/8 inch projection from the door face.
H. The design of the exit device shall eliminate the necessity of removing the device from the door for standard maintenance or keying changes.I. The device chassis shall be mounted and operable without the need of the rail or the chassis cover.J. Trim shall be through-bolted.K. Devices shall be available with matching trim for both wide and narrow stile doors, including electrified functions when required.L. Exit device operating lever trim shall withstand 1000 inch pounds of torque without allowing access.M. Lever trim shall be available in architectural finishes and designs to match that of the locksets specified.N. Exit devices shall have a five year limited warranty.The following guidelines should be referenced regularly and as required for proper appearance and longevity of finish.
2.01 EXIT DEVICES
*To avoid discoloration and pitting:• Keep stainless steel away from contact with other metals• Avoid cleaning with mineral acids or chlorine products• Avoid cleaning with abrasive products like sandpaper or steel wool
To maintain the finish:• Remove any contamination before damage occurs• Protect with a metal polish or car wax
CPC – Clear Powder CoatFor use in pool areas, offshore applications and highly corrosive applications, the clear powder coat eliminates need for cleaning and maintenance offinish. Applied over 32D only.
3 605 Bright brass, clear powder coat
Mild non-abrasive detergentwith damp cloth or sponge
Abrasive cleaners, bleach solvents,steel or bronze wool
4 606 Dull brass, clear powder coat
9 611 Bright bronze
10 612 Dull bronze, clear powder coat
10B 613 Antique bronze, oiled Lemon oil polished with dry cloth Abrasive cleaners, bleach solvents,steel or bronze wool
10BL – Oxidized satin bronze-lacquered
Mild non-abrasive detergentwith damp cloth or sponge
Abrasive cleaners, bleach solvents,steel or bronze wool
15 619 Satin nickel plate
20D – Statuary bronze, dark
26 625 Bright chrome
26D 626 Dull chrome
32 628 Bright stainless steel
32D 630 *Dull stainless steel Plastic pad or bronze wool Cleaners, solvents, bleach, steel wool
Finish
SARGENT# BHMA# Description How to clean Avoid these cleaners
80 Series Architectural Specifications, Finishes and Finish Care
1-800-727-5477 • www.sargentlock.com4
8888/8810 Multi-Function RimExit Device & Trim80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
649 Strike• Supplied standard for panic& fire rated openings
• Surface applied• Black nylon coated
700 Series ET Control
The 700 Series ET Control is sold separatelyfrom the exit device and can be used with8888 & 8810 Exit Device. The trim is nonhanded and is through-bolted to thechassis for greater security and durability.Available in 7 functions and SARGENTStudio, Coastal and standard lever designsto accommodate most requirements.• ANSI/BHMA Finishes• Easy operating lever handle allows
convenient one hand operation• ET trim is not available in 32 or 32D• Stainless steel levers are available
For Doors Wood or metal. 1-3/4" (44 mm)minimum thickness. For doorsover 1-3/4" to 2-1/4" thick, specify thickness and order as 31- option
Mounting Supplied standard with wood andmachine screwsAvailable with through-bolts andmortise nuts
Chassis Cover Cold drawn stainless steel, brass or bronze with ANSI/BHMA FinishesChassis Nonferrous alloy (Panic) Ferrous alloy (Fire Rated)Rails Roll Formed Stainless Steel, Brass or Bronze with ANSI/BHMA FinishesHand Non-handedDogging Feature Hex key dogging standard on non fired rated devices; specify 16- for(Non 12- only) cylinder dogging (#41 cylinder supplied)Latchbolt Stainless steel, 3/4" (19mm) throwStrike 649 Strike supplied standard for panic & fire rated openingsFire Exit Hardware See chart - Page 3
LBROSE: LLEVER: B
Specifications
13/16"(21mm)
1-13/16"(46mm)
8-1/16"(205mm)
3-9/16" MAX*(90mm)
8888/8810 Multi-Function exit device and trim• Device & trim sold separately; easy to mix andmatch• Designed for standard width stile applications on wood and
metal doors• 7 functions available as determined by the trim function• 3 trim designs available:
- 700 ET Controls- 88 Lever & Rose trim- Pull trims
• Single and double door applications with a mullion
Rail Chart- Rails are available in 4 sizes, use door width to determine size needed.- Rails will be factory cut to size if door width is supplied or can be cut in the field
The 8888/8810 Rim Exit Device• Devices are ANSI A156.3 – 2008 Grade 1• UL Fire and Panic listed• Device is non-handed• ANSI/BHMA architectural finishes• Four standard sizes availableTo Order: Specify options, 8888 or 8810,Rail Size and FinishExample: 12-19-8888F x 32D
3/4"(19mm) 1/4"
(6mm)
688 Trim Retrofit Kit
• 688 Trim Retrofit kit allows an8810/8888 rim exit with an ET toreplace Von Duprin's 98/99 seriesexit with trim with minimaldoor prep.
• Order as: 688 Kit
Stock Size DoorWidths Remarks
E 24" to 32" (61cm to 81cm) No cutting required for 32" (81cm) door
F 33" to 36" (84cm to 91cm) No cutting required for 36" (91cm) door
J 37" to 42" (94cm to 107cm) No cutting required for 42" (107cm) door
G 43" to 48" (110cm to 122cm) No cutting required for 48" (122cm) door
1-5/32"(29mm)
3-11/16"(94mm)
• The 88 Lever and Rose Trim is sold separately fromthe exit device and can be usedwith 8888&8810 Exit Device.
• The trim is non handed and is through-bolted tothe chassis for greater security and durability.Available in 4 functions and 4 lever designs toaccommodatemost requirements.
88 Lever and Rose Trim
1-800-727-5477 • www.sargentlock.com 5
8888/8810 Multi-Function RimExit Device & Trim80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
Trim Designations
SARGENTFunctionNumbers
ANSIFunctionNumbers
ANSIFunctionNumbers
Description & Cylinder Info(1-3/4" Door)
Freewheeling TrimThe lever rotates when the door islocked preventing excessive force frombeing applied to the horizontal lever
Keyed & Non Keyed Pull Trim for 8888 & 8810 Devices
Use the six digit designation (Ex "866-MAL") when ordering trimwithout an Exit Device, always specify options, designation, finish& hand
Example: 10-SG-814-FSW x 04 x RHR
SARGENTFunction #'s ANSI
Description & Cylinder Info.(1-3/4" Door)
AvailableFinishes
SARGENTFinishes
ANSIFinishes
0304091010B10BL141520D2626D3232D
605606611612613614618619624625626629630
700 Series ET Trim
04 03Night Latch
Key Retracts Latch#34 Cylinder Supplied
704 ET_ x Hand & Finish
10 02 No outside operation (No Cylinder)ET Control is used as Pull Only 710 ET_ x Hand & Finish
13 08 Key Outside Unlocks/Locks Trim#41 Cylinder Supplied 713-8 ET_ x Hand & Finish
15 14 Passage Only (No cylinder) 715-8 ET_ x Hand & Finish
40 02Freewheeling Trim -No outside operation
(No Cylinder) Dummy Trim740 ET_ x Hand & Finish
43 08Freewheeling Trim -
Key Outside Unlocks/Locks Trim#41 Cylinder Supplied
743-8 ET_ x Hand & Finish
44 03Freewheeling Trim -Key Retracts Latch
#34 Cylinder Supplied744 ET_ x Hand & Finish
03 Key Retracts LatchCylinder Supplied 88-KL_ x Finish
02 No outside Operation (No Cylinder)Dummy Trim 88-DL_ x Finish
08 Key Outside Unlocks/locks TrimCylinder Supplied 88-CL_ x Finish
14 Passage Only (No cylinder) 88-LL_ x Finish
04 03 Key Retracts Latch#34 Cylinder Supplied 814-FSL* 814-FSW* 814-MSL* 814-PSB* 814-STS
10 02 No O/S Operation or Cylinder(Pull Only) 810-FLL 810-FLW 810-MAL 810-PTB 810-STS
Note: ET trim is not available in 32 (629) or 32D (630)
Lever Designs available for 88 Lever & Rose Trim are L, B, J & P
Note: For 88 Lever & Rose trim, the 1st letter is the function, the 2nd is the “L” Rose Design & the 3rd is the leverdesign specified
Note: FSW, FLW, 88 Lever & Rose trim & ET’s are not available in 32(629) or 32D(630)* FSL, FSW, MSL and PSB trims are used with (HC-& 12-) 8888 and 8804 only and are the same as FLL, FLW, MAL and PTB pulls, except for cylinder hole located 3/8" (9mm) lower.
Options
Exit Trim
12-*16-19-43-GL-CPC-LC-LD-PL-
10-**10-UL-
11-11-70-
11-72-7P-11-73-7P-
21-22-60-63-64-+70-+72-+73-
+73-7P-+65-73-
+65-73-7P-BR-LC-SC-SE-
++ SF-SG-
Trim Designations
How to order 8888/8810 Multi-Function Exit Devices:Specify the following:
Options Series Rail Finish16- 8888 or 8810 F 32D
• All trims and functions listed on this page, work with 8888 & 8810 Exit Devices• Available options listed at the right• 8888 & 8810 are identical products and are non-handed• Exit devices are not available in 14, 15, 26 and 26D finishes
How to order trim for 8888 & 8810 Exit Devices:Specify the following:
Options Trim Designation Hand Finish10- 713-8 ET_* RHR 26D10- 88-CL_ * Non-Handed 10B60- 814-MSL RHR 04
*Specify lever designAvailable Options listed at the right
* Supplied withstandard 41 cylinder,for cylinder options,see trim options
** Double asteriskedoptions are notavailable with 88Lever & Rose Trim
+ Single crossed optionsare not available with88 Lever & Rose Trimwith J Lever
++ Double Cross optionsare only availablewith 88 Lever & RoseTrim
88 Lever and Rose TrimTo order: Specify options followed bytrim designation, lever design andfinish (as shown to the right).
Example: 10-SG-88-CLP x 26D
Description Trim Designations
700 Series ET ControlsTo order: Specify options followed bytrim designation, lever design, handand finish (as shown to the right).Example: 11-SG-713-8 x RHR x 10B
1-800-727-5477 • www.sargentlock.com 7
8800 Functions & Trims80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
8800Panic& Fire
Options Series Function Rail Lgth Trim Hand Outside Finish Inside Finish Door WidthF1-83-56 88 13 F ETL RHR 26D 32D 36"
04 03Night Latch
Key Retracts Latch#34 Cylinder Supplied
8804 x ET_
06 09Key unlocks Trim, Trim retracts latch/Trim relocks when key is removed
#41 Cylinder Supplied8806 x ET_
10 01 No outside operation (No Cylinder) 8810
10 02 No outside operation (No Cylinder)ET Control is used as Pull Only 8810 x ET_
13 08 Key Outside Unlocks/locks Trim#41 Cylinder Supplied 8813 x ET_
15 14 Passage Only (No cylinder) 8815 x ET_
16 10Key Outside Retracts Latch;
Key Inside Unlocks/Locks O/S TrimO/S #34 Cylinder & I/S #44 Cylinder Supplied
8816 x ET_
40 02Freewheeling Trim -No outside operation
(No Cylinder) Dummy Trim8840 x ET_
43 08Freewheeling Trim -
Key Outside Unlocks/locks Trim#41 Cylinder Supplied
8843 x ET_
44 03Freewheeling Trim -Key Retracts Latch
#34 Cylinder Supplied8844 x ET_
46 09Freewheeling Trim -
Key unlocks Trim, Trim retracts latch/Trim relocks when key is removed
#41 Cylinder Supplied8846 x ET_
73 Electrified ET Trim - Fail SafePower Off, Unlocks Lever (No Cylinder) 8873 x ET_
74 Electrified ET Trim - Fail SecurePower Off, Locks Lever (No Cylinder) 8874 x ET_
75Electrified ET Trim - Fail Safe
Power Off, Unlocks Lever, Key Retracts Latch#34 Cylinder Supplied
8875 x ET_
76Electrified ET Trim - Fail Secure
Power Off, Locks Lever,Key Retracts Latch
#34 Cylinder Supplied8876 x ET_
ANSI Type 1Options
Description & Cylinder Info(1-3/4" Door)
8800Panic & Fire
8800
Mechanical Options:12-16-19-31-36-37-43-53-54-55-56-
56-HK-57-58-59-
BC-59-76-85-86-87-AL-BT-CPC-GL-LD-PL-SG-TB-TL-
Cylinder Options:10-
10-21-10UL-10-63-11-
11-21-11-60-11-63-11-64-
11-70-7P-11-72-7P-11-73-7P-
11-65-73-7P-21-22-51-52-60-63-64-70-72-73-
65-73-65-73-7P-73-7P-81-82-
F1-82-83-
F1-83-84-BR-LC-*SC-*SE-
Lever Designs for ET ControlsA, B, E, F, J, L, P, W
Also available with Coastal Series &Studio Collection Levers
ET Designation with Suffix(Used to order ET without device)
8800 Series: 704, 706-8, 710, 713-8,715-8, 716, 740, 743-8, 744, 746-8,773-8, 774-8, 775-8 & 776-8
Freewheeling TrimThe lever rotates when the door islocked preventing excessive force frombeing applied to the horizontal lever
Note: Exit devices are available in all standard finishes, except 14, 15, 26 & 26D. With these finishes, exit devices are supplied in 32or 32D tomatch accordingly. 26 or 26D is automatically supplied when 32 or 32D is specified. For nickel finishes, specify 14/32 or15/32D to receive nickel finished trims and stainless exit devices.
* FSL, FSW, MSL and PSB trims are used with (HC-& 12-) 8888 and 8804 only and are the same as FLL, FLW, MAL and PTB pulls except for cylinder hole located 3/8" (9mm) lower.Note: Thumb piece trims for 63 and 66 function devices are identical and are identified as 66 function when trim is ordered separately.Note: FLW & FSW trims are not available in 32(629) or 32D(630)
* Options are notavailable with 8816
Description &Cylinder Info.(1-3/4" Door)
04 03Night Latch
Key Retracts Latch#34 Cylinder Supplied
814-FSL* 814-FSW* 814-MSL* 814-PSB* 814-STS 8804 x Trim
Designation
AvailableFinishes
10 02 No O/S Operation orCylinder (Pull Only) 810-FLL 810-FLW 810-MAL 810-PTB 810-STS 8810 x Trim
Designation
SARGENTFinishes
ANSIFinishes
28 15 Passage Only(No cylinder) 828-FLL 828-FLW 828-MAL 828-PTB 828-STS 8828 x Trim
Designation
0304091010B10BL141520D2626D3232D
605606611612613614618619624625626629630
63 05Key Outside Unlocks/
Locks Trim#34 Cylinder Supplied
866-FLL 866-FLW 866-MAL 866-PTB 866-STS 8863 x TrimDesignation
66 07Key Outside Retracts Latch;Key Inside Unlocks/Locks O/S
Trim O/S #34 & I/S #44866-FLL 866-FLW 866-MAL 866-PTB 866-STS
N/A
N/A
N/A
862 Pull
862 Pull
8866 x TrimDesignation
700 Series ET TrimExits with ET Trim, specifylever design after the ETdesignation (e.g., ETL)
SeriesTrim Designations• Use three letter designations (Ex “PTB”) when ordering theExit Device with trim
• Use the six digit designation (Ex “866-MAL”) whenordering trim without an Exit Device, always specify finish
Pull & Thumb Piece Trim Section
SARGENTFunctionNumbers
ANSIFunctionNumbers
SARGENTFunctionNumbers
ANSIFunctionNumbers
Electrified ET TrimVoltage must be specified for thefollowing functions: 73, 74, 75 and 76.Specify: 12VDC or 24VDC
1-800-727-5477 • www.sargentlock.com62
ET Trim, Levers and Pulls80 Series
W Lever
J Lever*
Pulls
F LeverE Lever
P Lever*L Lever*
A Lever B LeverET Lever Controls
*Projection varies by lever design.2-1/2" (63mm) projection withL Lever
* Lever returns within 1/2" (13mm) of door face
• Handed
3-1/8"(79mm)
13/16"(21mm)
4-5/8"(117mm)
13/16"(21mm)
4-1/2"(114mm)
1/2"(13mm)
863 864862
10"(254mm)MTGHoles
4"(102mm)
18"(457mm)MTGHoles
4"(102mm)
10"(254mm)MTG Holes
3-1/2"(89mm)
3/4" Dia.(19mm)
1" Dia.(25mm)
1" Dia.(25mm)
13/16"(21mm)
1-13/16"(46mm)
8-1/16"(205mm)
3-9/16" MAX*(90mm)
3-1/2"(89mm)
13/16"(21mm)
4-1/2"(114mm)
13/16"(21mm)
4"(102mm)
3-1/4"(83mm)3"
(76mm)
4"(102mm)
13/16"(21mm)
1/2"(13mm)2-3/4"
(70mm)
13/16"(21mm)
4-11/16"(119mm)
3"(76mm)
13/16"(21mm)
5/16"(8mm)
4-15/16"(125mm)
90°
1-3/4"(44mm)
2-3/4"(70mm)
3"(76mm)
13/16"(21mm)
4-11/16"(119mm)
2-3/8"(60mm)
SIDE PROFILE
Note: ET suffixes required when ordering ETtrim without an exit device, see page 71 forcomplete details
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
1-800-727-5477 • www.sargentlock.com 63
Coastal Series Levers &Thumb Piece Pulls80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
• Specify hand when ordering• Specify hand when ordering • Specify hand when ordering
C* - Coronado™ R - Rockport™
Y - Yarmouth™ G - Gulfport™ S - Sanibel™
2-1/2"(64mm)
13/16"(21mm)
4-1/4"(108mm)
3-1/4"(83mm)
13/16"(21mm)
4-1/2"(114mm)
3-1/2"(89mm)
13/16"(21mm)
4-1/2"(114mm)
4-1/16"(103mm)
13/16"(21mm)
4-1/2"(114mm)
2-3/4"(70mm)
13/16"(21mm)
4-3/4"(121mm)
PTB/PSB
MAL/MSL
STS
FLW/FSWFLL/FSL1-3/4"
(44mm)2-1/16"(52mm)
6"(152mm)
14-5/16"(364mm)
1-3/4"(44mm)
14-5/16"(364mm)
2-1/16"(52mm)
6"(152mm)
2-1/16"(52mm)
2-5/8"(67mm)
14-1/4"(362mm)
6"152mm
802-PTB
2-1/16"(52mm)
3-1/2"(98mm)
15"(381mm)
6"152mm
6"(152mm)
3-1/2"(89mm)
1-15/16"(49mm)
15"(381mm)
1-5/8"(41mm)
2-1/4"(57mm)
7-3/16"(198mm)
9-5/8"(244mm)
• Coastal Series™ levers can be usedwithall SARGENT 80 Series exit devices with ET trim
• All levers – solid cast brass• All standard functions available• Finishes available: 03, 04, 09, 10, 10B, 10BL,14, 15, 20D, 26, 26D
* Lever returns within 1/2" (13mm) of door face
Pulls and Thumb Pieces TrimsThese trims are through-bolted, creating perfect alignment of center case, thumb piece and cylinder, as required. Through-bolts pass through thechassis of the devices and are bolted directly to the trim. FSL, FSW, MSL and PSB pulls are used with 12- 8804 and 8804 only, they are identical to FLL,FLW, MAL and PTB pulls except the cylinder hole is located 3/8" (9mm) lower. The 802-PTB plate is a flat plate which can be used to cover existing doorpreps and is as ANSI/BHMA function 01.
1-800-727-5477 • www.sargentlock.com64
Studio Collection Levers80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
Features• Studio Collection levers can be used with all SARGENT 80 Series exit devices with ET trim• All levers - solid brass or stainless steel• Available with all lever functions• Lever finishes available: 03, 04, 09, 10, 10B, 10BL, 14, 15, 20D, 26, 26D, 32 & 32D• Always specify hand
MO
ML
MZ*
MA
MC
MD
MJ
MP
ND*
NJ*
MQ
MR
MT
MM
MY*
MB
ME
MF
MG
MI
MW*
MN
MH
MK
MS
MU
MV
MX*
NS*
NU*
RCM**
RAL**
REM**
RAM**
RAS**
RAW**
Rialto Series
Odéon Series
Aventura Series
Centro Series
Notting Hill Series
* Lever returns within 1/2" (13mm) of door face ** The Gramercy Levers are customized. Refer topage 65 on how to order
Gramercy Series
Gramercy Lever information
1-800-727-5477 • www.sargentlock.com 65
Ordering GramercySeries Levers80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
Elements of Gramercy Series Leversgrip grip
shankshankshank
insert
REM RCM RAM, RAW, RAS, RAL
Lever Part Number Shank Finish* Insert Grip Finish
Plain† REM Polish Stainless (629) orSatin Stainless (630) n/a Polish Stainless (629) or
Satin Stainless (630)
With Raised Band RCM Polished Stainless (629) n/a Polish Stainless (629) orSatin Stainless (630)
With Metallic Insert RAM Polished Stainless (629) Satin Stainless(630) Polished Stainless (629)
WithWood Insert† RAW Polished Stainless (629) orSatin Stainless (630) Birch (BH) Polish Stainless (629) or
Satin Stainless (630)
With Santoprenne Insert† RAS Polished Stainless (629) orSatin Stainless (630) Black (BK) Polish Stainless (629) or
Satin Stainless (630)
With Leather Insert† RAL Polished Stainless (629) orSatin Stainless (630)
Black (BK) orBrown (BN)
Polish Stainless (629) orSatin Stainless (630)
* Rose and escutcheon finish is designated by shank finish selected† Grip finish must match shank finish
* Escutcheon finish is designated by shank finish selected
To order Gramercy Series levers with 80 Series products, see the example below. When specifying finish, use the last two digits of the BHMA standardfinish code, i.e. use “29” for polished stainless, BHMA finish 629.
Options Series Function RailSize Voltage Trim Lever Shank
Finish*InsertFinish
GripFinish Hand Inside
FinishDoorWidth
OpeningHeight AFF
Select from 80 Series catalog
Specifiedfor
electricalfunctions
Selectfrom80
Seriescatalog
Leatherinsert
Polishedor satinstainless
Black orbrown
Polishedor satinstainless
RHRRH,
LHR, orLH
Selectfrom
80 Seriescatalog
Forverticalrod
devices
AboveFinishedFloor
10- 87 73 F 12VDC F RAL 29 BN 29 RH 32D 36" 84" 41"
Sample order on how to specify anExit Device with Gramercy levers
1-800-727-5477 • www.sargentlock.com66
Anti-Vandal Trim, 988 Surface Bolt,ET Plates & Dummy Rails80 Series
9064
1:D
8/30
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
8893 Dummy Rail
A decorative push bar for vestibule doorapplications where continuity of design isdesired, but no exit device is required.Outside dummy trim available on order.
• Order as a: 8893 x finish; Specify door widthand door stile width when ordering.
8895 Active Dummy Rail
Push rail operates on this rail to simulateactive doors. Can be used with dummy trim.
• Order as a: 8885 x Finish; specify door widthand door stile width when ordering.
• Available with Request-to-Exit (REX) signalingswitch; specify 55-8895 x Finish
ET Cover Plate
This plate is designed to bemountedbehind the ET control to cover a stockhollowmetal cutout• Order as a: 68-0657 x finish
3-1/2"(89mm)
8-3/4"(222mm)
• Lexan touchpad replacement kit forall 80 Series push rails
• Direct replacement – uses existingmounting holes
• Order as a: 809 Touch Pad
809 Touchpad Kit
For all ET functions
Designed for exterior doors that requireextra security or resistance to vandalism,anti-vandal trim (AVT) plates have anextended lip on the active side of the doorto provide extra protection for thelatchbolt. A matte plastic coated gripprovides a comfortable pull over widetemperature ranges. Fully through-boltedwith no exposed exterior fasteners for acleaner look and increased security.
3-1/8"(79mm)
10-9/16"(268mm)
8-3/16"(208mm)
3-9/16"(90mm)
1-1/4" Dia.(32mm)
Anti-Vandal Trim
• Designed for severewindload (HurricaneCode) environmentswhere surface boltsare required (e.g., on inactive doors)
• Tested to Dade County protocols• Listed to UL 10C for use on fire rated
door assemblies. Refer to codes forlocations where surface bolts are allowedon fire doors
• All steel construction for maximumstrength and heavy duty use– Full 3/4" (19mm) square, 12" (305mm)
bolt with 1-1/4" (32mm) throw– Bright zinc-plated finish– Jimmy-resistant design locks bolt
automatically when thrown; releasedby pressing knob toward door whileretracting
– Bolt can be locked in retracted orthrown position
• Angle (L shaped) andmortise strike withmounting hardware supplied standard
• Order as a: 988 Surface Bolt
988 Surface Bolt Kit
Features• Heavy duty 12 gauge stainless steel in 32D finish• Through-bolted for added strength• Handed – Specify RHR or LHR• ADA Compliant• #34 Rim Cylinder supplied for 8804• #41 Mortise Cylinder supplied for 8904• Night Latch and Dummy Functions available• Available for MD &WD8610, 8710, 8804, 8810,8904 & 8910 Devices
•Without protective lip for inactive door• AVT Retrofit Kit works easily with existing productwith minor prep modification
• Order by part number (826, 824, 821 or 827) asdetermined by product & function below
Part Number Description Application
826 Cylinder, but NoProtective Lip 8804 Mfg after 02-2001
824 Protective Lip &Cylinder
8904; also 8804 Mfgbefore 02-2001
821 No Protective Lip& No Cylinder
MD &WD8610, 8710and 8810
827 Protective Lip &No Cylinder 8910
821 for use on all inactive leafs
611/0
1/07
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2007
All
rig
hts
res
erve
d
1-800-727-5477 • www.sargentlock.com
Holders & Stops 1540 Series Standard Duty
Overhead Surface Mount
11/0
1/07
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2007
All
rig
hts
res
erve
d
1540 Series
• Surface application for interior single acting doors. Three types to choose from:
– "H" Holder; Stops and Holds doors open
– "S" Stop; Stops door only– "F" Friction Type; Holds door open
• Holder/Stop is surface mounted with arm and bracket attached to top jamb
Hold Open With Stop Type:• Holds door open for a particular degree
from 85° to 110°
• Hold-open feature engages and releases easily by a push or pull action
• Release tension is easily adjustable
Stop Only Type:• Used to stop door with shock absorber
spring
• Protects wall and door
• Maximum door opening 110°
Friction Type:• Prevents unwanted movement of door
• Not for use with a door closer
• Can be held in any position up to 110°
• Friction unit is made of heavy duty brake lining type material
• Adjustable friction control
ANSI A 156.8 Grade 11540 F Series complies to C055311540 H Series complies to C055111540 S Series complies to C05541
UL Classified• SARGENT 1540 Series stops are UL10B & 10C
classified by Underwriter Laboratories asMiscellaneous Fire Door Accessories
Note: Stops are not rated. The door and frame carry the fire rating
AccessoriesShims• Optional 1/4" thick jamb bracket shims for
use with frames with blade stops.
Machine Screws• Order as required by 21-0198 x finish
• Used with above shims up to 3/4" thick.Four required per overhead. Order by 01-3436 x finish (12-24 x 1-1/4")
• Standard screw pack 21-2031 x finish
Specifications
For Doors Interior doors 18-1/2" up to 48" wide*, 1-3/8" to 1-3/4" thick, as standard see below for correct size.
Finishes 03, 04, 9, 10, 10B, 10BL, 15, 20D, 26, 26D EN, EB, ED, EAB, EP Powder coat
Options 31- Prefix for use on doors more than 1-3/4" up to 2-1/4" thick. Specify door thickness. 36- Prefix Torx Security machine screws 6 required
No. 145 Angle Bracket
For Flush Door and Frames
Series 1540 Overhead Door Holders can bemounted on flush doors and frames usingthe No. 145 Angle Bracket. This bracketallows the mounting of the arm to the top casing. Bracket is not handed.
Surface Application1540 Series
Sizing Chart
Actual Hold-Open FrictionWidth of Door with Stop Stop Only Stop/Holder
18-1/2" – 25" 1546H 1546S 1546F
25-1/8" – 32-1/2" 1547H 1547S 1547F
32-5/8" – 40" 1548H 1548S 1548F
40-1/8 – 48" 1549H 1549S 1549F
How to Order
Specify number, letter suffix, and finish. Example: 1537F x 03
1540 Series furnished with through-bolt and grommet nut for mounting on doors, 1-3/8" to 1-3/4" thick only. For other doors up to 2-1/4" thick, specify thickness when ordering.For center hung pivots, consult factory.
1548S Shown
145 ANGLE BRACKET SHOWN WITH 1540WITH FLUSH TRANSOM OR RABBETED DOORS
145 Angle Bracket
* When using vertical rod exit devicesand or surface/flush bolts, use cautionin choosing the proper size to ensurecompatibility
8 1-800-727-5477 • www.sargentlock.com
Holders & Stops 1560 Series Electromagnetic
Door Holders
11/0
1/07
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2007
All
rig
hts
res
erve
d
• Designed for use with self-closing fire and smoke barrier doors
• Use independently or with any fire or smoke detector system
• When de-activated, helps control the spread of fire and smoke by automaticallyreleasing doors from an open position for simultaneous closing
• Fail-safe device: When electrical power fails, doors will release to close automatically
• Conforms to devices outlined in National Fire Protection Agency Standards Nos. 80 and 101
• Designed to work with SARGENT doorclosers
• Recommended vertical location is on top rail of door – within 6" of lock stile edge
• When applications will not allow wall orfloor magnets, consult SARGENT’sFireGuard catalog for our line ofElectronic Closer Holders
• Fits standard outlet box
• Holding force – 35 lbs typical
• Voltage and Current:120 VAC, 60 Hz., .020 amp24 VAC/DC, 60 Hz., .020 amp12 VDC, .040 amp
• Finish – EN
• Meets ANSI A156.15
• UL – UL Listed to U.S. and Canadian safety standards
• 1" (25mm) extension included standard to increase armature projection to 2-5/8"(67mm)
Electromagnetic Door Holder
1561 Flush Mount
2-1/2"(64mm)
2-3/4"(70mm)
4-5/8"(117mm) 2-17/32"
(64mm)
1-5/8"(41mm)
1-3/4"(44mm)
1560 Surface Mount
1561 1560
1562 Single Floor Mount 1563 Double Floor Mount
Floor Mount
4-3/4"(121mm)
3-1/8"(79mm)
5"(127mm) 1-3/4"
(44mm)1-5/8"
(41mm)
2-17/32"(64mm)
5"(127mm)
3-1/8"(79mm)
1-5/8"(41mm)
4-3/4"(121mm)
1562 1563
1"(25mm)
Wall Mount
1-800-727-5477 • www.sargentlock.com66
Anti-Vandal Trim, 988 Surface Bolt,ET Plates & Dummy Rails80 Series
9064
1:C
1/15
/10
Copyright©1998-2010,SargentManufacturingCompany,anASSAABLOYGroupcompany.Allrightsreserved.
ReproductioninwholeorinpartwithouttheexpresswrittenpermissionofSargentManufacturingCompanyisprohibited.
8893 Dummy Rail
A decorative push bar for vestibule doorapplications where continuity of design isdesired, but no exit device is required.Outside dummy trim available on order.
• Order as a: 8893 x finish; Specify door widthand door stile width when ordering.
8895 Active Dummy Rail
Push rail operates on this rail to simulateactive doors. Can be used with dummy trim.
• Order as a: 8885 x Finish; specify door widthand door stile width when ordering.
• Available with Request-to-Exit (REX) signalingswitch; specify 55-8895 x Finish
ET Cover Plate
88-E-PTB
The 88-E-PTB is designed to bemountedbehind the ET control to cover a stockhollowmetal cutout• Order as a: 68-0657
3-1/2"(89mm)
8-3/4"(222mm)
• Lexan touchpad replacement kit forall 80 Series push rails
• Direct replacement – uses existingmounting holes
• Order as a: 809 Touch Pad
809 Touchpad Kit
For all ET functions
Designed for exterior doors that requireextra security or resistance to vandalism,anti-vandal trim (AVT) plates have anextended lip on the active side of the doorto provide extra protection for thelatchbolt. A matte plastic coated gripprovides a comfortable pull over widetemperature ranges. Fully through-boltedwith no exposed exterior fasteners for acleaner look and increased security.
3-1/8"(79mm)
10-9/16"(268mm)
8-3/16"(208mm)
3-9/16"(90mm)
1-1/4" Dia.(32mm)
Anti-Vandal Trim
• Designed for severewindload (HurricaneCode) environmentswhere surface boltsare required (e.g., on inactive doors)
• Tested to Dade County protocols• Listed to UL 10C for use on fire rated
door assemblies. Refer to codes forlocations where surface bolts are allowedon fire doors
• All steel construction for maximumstrength and heavy duty use– Full 3/4" (19mm) square, 12" (305mm)
bolt with 1-1/4" (32mm) throw– Bright zinc-plated finish– Jimmy-resistant design locks bolt
automatically when thrown; releasedby pressing knob toward door whileretracting
– Bolt can be locked in retracted orthrown position
• Angle (L shaped) andmortise strike withmounting hardware supplied standard
• Order as a: 988 Surface Bolt
988 Surface Bolt Kit
Features• Heavy duty 12 gauge stainless steel in 32D finish• Through-bolted for added strength• Handed – Specify RHR or LHR• ADA Compliant• #34 Rim Cylinder supplied for 8804• #41 Mortise Cylinder supplied for 8904• Night Latch and Dummy Functions available• Available for MD &WD8610, 8710, 8804, 8810,8904 & 8910 Devices
•Without protective lip for inactive door• AVT Retrofit Kit works easily with existing productwith minor prep modification
• Order by part number (826, 824, 821 or 827) asdetermined by product & function below
Part Number Description Application
826 Cylinder, but NoProtective Lip 8804 Mfg after 02-2001
824 Protective Lip &Cylinder
8904; also 8804 Mfgbefore 02-2001
821 No Protective Lip& No Cylinder
MD &WD8610, 8710and 8810
827 Protective Lip &No Cylinder 8910
821 for use on all inactive leafs
Profile Series v.G1.5Stand-Alone Access Control ProductsAccessories
1-800-727-5477www.sargentlock.com
Profile Series v.G1.5Stand-Alone Access Control ProductsOverview for v.G1.5 Profile Series
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
1An ASSA ABLOY Group company
OverviewThe enhanced v.G1.5 Profile Series of stand-alone access control products combines a broad selection of technologies and new programmingfeatures with ANSI/BHMA Grade 1 mechanical locks, housed in a sleek, architecturally pleasing design. Starting with the G1-LU series whichoffers keypad only to the full-featured G1-TP Series which includes keypad, proximity and RF technology. The locks are programmed via PDAdata transfer, all units utilize a battery powered microprocessor based controller with non-volatile memory to preserve user's codes.
The Profile Series v.G1.5 is available with SARGENT 8200 series mortise lock, the 10 line cylindrical lock and the 80 series rim and mortise exitdevices. These locking devices are UL Listed for use on fire doors. All technologies with the keypad feature offer access codes which may varyfrom 1 to 6 digits and utilize a master code for keypad programming. Various locking modes allow the operation of the lock to be tailored toeach opening and individual user, typical modes include panic, adjustable momentary unlock and passage.
“G1.5-LU” (keypad only) configuration of stand-alone access control products are ideal for dormitories, assisted living facilities, hospitals,retailers, apartments and office complexes. Programming is accomplished through the keypad for most basic functions or via SofLink PlusPDP™ application software.
“G1.5-PK” (proximity/keypad) version of stand-alone access control products offers the highest level of security and flexibility. These productscan be programmed via keypad or SofLink Plus™ w/ SofLink PDP™ requiring both a code (1-6 digits) and proximity card/fob/tag presentationto gain entry. It can also be programmed for keypad or proximity presentation only.
“G1.5-PA” (proximity only) configuration of access control provides a higher level of security. All programming must be handled through theSofLink Plus™ w/SofLink PDP™ application software. This configuration is ideal for high traffic applications where keypad usage is notdesirable: universities, laboratories or hospitals. A “master” Comm Enable proximity card or fob is required to initiate programming of thelock.
"G1.5-TU" (keypad and RF technology) series of access control offer the convenience of the keypad along with the RF technology whichallows for remote unlocking and locking of the unit. This configuration is ideal where security is a concern (offices and medical clinics).
"G1.5-TP" (keypad, proximity and RF technology) series of access control offers all three technologies allowing the lock to be programmed torespond to any of the technologies as needed.
"G1.5-TA" (proximity and RF technology) series offers the additional security of eliminating the keypad with the convenience of remoteunlocking and locking through the RF technology.
1-800-727-5477www.sargentlock.com
The AgION antimicrobial is not intended as a substitutefor good hygiene. Coated products must still be cleanedto insure the surfaces will be free of destructivemicrobes. SARGENT makes no representations or warranties, express or implied, as to the efficacy of theAgION antimicrobial. A copy of the AgION warranty isavailable upon request.
SARGuard Coating
Cylindrical Design Mortise Design Exit Device Design
• Revolutionary finish coating available on all SARGENT product lines, utilizes a silver-based antimicrobial compoundfrom AgION Technologies
• As an integral part of the finish coating, SARGuard lasts for the life of the hardware
• SARGuard coating permanently suppresses the growth of bacteria, algae, fungus, mold and mildew. It is effective againsta broad spectrum of bacteria.
• Non-toxic and completely safe. The AgION antimicrobial compound is EPA and NSF approvedand FDA listed for use in medical and food preparation equipment.
• Applications: Anywhere there is need for a clean environment (hospitals, laboratories, schools, medical centers, daycare, food processing etc.)
Profile Series v.G1.5Stand-Alone Access Control ProductsAccessories
1-800-727-5477www.sargentlock.com
Profile Series v.G1.5Stand-Alone Access Control Product Product Features & Comparisons
1-800-727-5477www.sargentlock.com
An ASSA ABLOY Group company
Feature Comparisons
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
2
Standard Features• Audit Trail provides parameters such as
access granted in, access denied, entry into programming mode, date, time, user and door information
• Low battery indication – four chirps aftercode entry. Master and emergency codewill operate lock after the low batteryindication period has passed and usercodes no longer operate the lock
• Moisture resistant coating on electronics• Entry of three wrong user codes in
succession disables all codes for tenseconds
• UL Listed to Canadian safety standards• Forced and propped door option• For use on exterior doors with weatherseal
gasket, conduit and shroud (optional,order separately)
• Remote power and request to enteravailable – requires wire harness (52-3010)and hard wiring
• One master code – forced master codefrom factory default assigns emergency,supervisory and user codes and allowsentry when deadbolt is thrown (mortiselocks)– Multiple supervisory codes – allow
temporary lockout of selected users,change unlock time duration,requestinfrared interrogation output and adduser codes
– One emergency code – allows entrywhen dead bolt is thrown (mortiselocks). Unlocks after the low batteryindication period has passed and usercodes no longer operate lock
– Temporary codes by number of uses (1-500), start-and-stop dates or totaldays after first use (24 hour specific)
– Maintained (passage) code – unlocks forextended periods of time
Keypad Features• LEDs on unit indicate status – green
indicates unlocked; yellow indicatesprogramming mode
Proximity Features• Supports all HID 125 KHz Wiegand formats
(up to 40 bit) by Keypad Presentation orwhen using proximity enrollment stationES-G1 with SofLink Plus 5 software
• Supports 26, 34, & SARGENT 1000 (33 bit)HID formats with SofLink PlusTM version 4.0or higher software programming
Access v.G1.5-LU v.G1.5-PK v.G1.5-PA v.G1.5-TU v.G1.5-TP v.G1.5-TAStand Alone Unit Yes Yes Yes Yes Yes YesKeypad Yes Yes - Yes Yes -Proximity - Yes Yes - Yes YesRF Technology - - - Yes Yes YesProgramming PDA/Keypad PDA/Keypad PDA PDA/Keypad PDA/Keypad PDASupports all HID Proximity Bit Format - Yes Yes - Yes -SofLink Plus™ with PDA Yes Yes Required Yes Yes RequiredDirectly supports 26, 33 & 34 bit 125 kHZ HID Wiegand bit formats* - Yes Yes - Yes YesSupports all 125kHz HID Wiegand (up to 40) bit formats with Enrollment Station - Yes Yes - Yes YesNon Volatile Memory Yes Yes Yes Yes Yes Yes
Power Requirements v.G1.5-LU v.G1.5-PK v.G1.5-PA v.G1.5-TU v.G1.5-TP v.G1.5-TABattery Life (Estimate) 75,000 cycles 75,000 cycles 75,000 cycles 4-1/2 Mo. 4-1/2 Mo. 4-1/2 Mo.Batteries 6 "AA" 6 "AA" 6 "AA" 6 "AA" 6 "AA" 6 "AA"Low Battery Indication Yes Yes Yes Yes Yes YesHard Power Available Yes Yes Yes Yes Yes Yes
Users & Codes v.G1.5-LU v.G1.5-PK v.G1.5-PA v.G1.5-TU v.G1.5-TP v.G1.5-TA# of Users Supported per Lock 2,000 2,000 2,000 2,000 2,000 2,000# of Users Supported by Database 20,000 20,000 20,000 20,000 20,000 20,000Audit Trail 2,000 2,000 2,000 2,000 2,000 2,000Code: Number of Digits 1 to 6 Digits 1 to 6 Digits - 1 to 6 Digits 1 to 6 Digits -Master, Emergency & Supervisory Codes Yes Yes Yes Yes Yes YesStandard, Extended, Passage Codes Yes Yes Yes Yes Yes YesPanic, Lockout Codes Yes Yes Yes Yes Yes YesComm Unlock, Relock Codes Yes Yes Yes Yes Yes YesTemporary User Codes Yes Yes Yes Yes Yes Yes
Features v.G1.5-LU v.G1.5-PK v.G1.5-PA v.G1.5-TU v.G1.5-TP v.G1.5-TAReal Time Clock with Date & Time Yes Yes Yes Yes Yes YesUp to 8 Time Zones per Lock Yes Yes Yes Yes Yes YesHolidays (16 Single & 16 Blocked) Yes Yes Yes Yes Yes YesDaylight Savings Time Yes Yes Yes Yes Yes YesAuto Unlock Yes Yes Yes Yes Yes YesAuto Unlock with First In Yes Yes Yes Yes Yes Yes
Adjustable Features v.G1.5-LU v.G1.5-PK v.G1.5-PA v.G1.5-TU v.G1.5-TP v.G1.5-TAUnlock Time Adjustability 1-99 Sec 1-99 Sec 1-99 Sec 1-99 Sec 1-99 Sec 1-99 SecAudible Keystroke Beep Available Yes Yes - Yes Yes -Remote Unlocking Yes Yes Yes Yes Yes YesUL Listed for Fire Doors Yes Yes Yes Yes Yes Yes
Note: Dash ( - ) means either Not Available or Not Applicable* Directly supports 35 bit (Corporate 1000) or other formats with special requirements. Consult factory.
Profile Series v.G1.5Stand-Alone Access Control ProductsAccessories
1-800-727-5477www.sargentlock.com
Profile LK Series (100 Users)Profile LU, PK & PA Series (500 Users)Access Control Products
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
3An ASSA ABLOY Group company
1-800-727-5477www.sargentlock.com
• The Profile LU, PK & PA products are available and supported for facilities with existing Profile Series product (Previous to v.G1 & v.G1.5).
• The Profile LU, PK & PA Series software and electronics are not compatible with the Profile Series v.G1 & v.G1.5 product. Please consult factory when ordering software for this product,and reference table on page 14 for replacement keypads and controllers.
All Profile Series configurations (LK, LU, PK & PA) are available withSARGENT 8200 Series Mortise Locks, 10 Line Cylindrical Locks and 80Series Rim and Mortise Exit Devices. Available functions are thesame as the v.G1.5 as listed on the following pages.
The Profile “LK” stand-alone access control products are designedfor areas that require authorized entry, such as stairwell doors,meeting rooms, company health clubs, etc. Microprocessor basedtechnology with non-volatile solid state memory ensures that codeswill not be lost even if batteries stop functioning. The controllerretains a total of 100 different user codes varying in length from oneto six digits. All programming is done through the keypad.
The “LU” (keypad only) configuration of stand-alone access controlproducts are ideal for dormitories, assisted living facilities, hospitals,retailers, apartments and office complexes. Programming is donethrough the keypad for most basic functions. The controller willretain a total of 500 different user codes varying in length from oneto six digits.
The “PK” (proximity/keypad) version of stand-alone access controlproducts offers the highest level of security and flexibility. Theseproducts can be programmed to require both a code (1-6 digits) andproximity card/fob/tag presentation to gain entry. It can also beprogrammed for keypad or proximity presentation only.
The “PA” (proximity only) configuration of access control provides ahigher level of security because all programming must be handledthrough previous version SofLink Plus™2.0 w/ SofLink PDP™ 1.0application software. This configuration is ideal for high trafficapplications where keypad usage is not desirable: universities,laboratories or hospitals. A “master” Comm Enable proximity card orfob is required to initiate programming of the lock.
Bored shown Mortise shown Exit Device shown
How To Order
SARGENT continues to offer the Profile LK Series (100 Users) and LU, PK & PA Series (500 user) product.
* Consult factory
Access LK LU PK PAStand Alone Unit Yes Yes Yes YesKeypad Yes Yes Yes -Proximity - - Yes YesProgramming Keypad PDA/Keypad PDA/Keypad PDASupports HID Proximity Bit Format - - Yes YesSofLink Plus™ 2.0 with PDA (serial connection only) - Yes Yes Required"Supports HID Bit Format 26, 33 & 34" - - Yes YesNon Volatile Memory Yes Yes Yes Yes
Power Requirements LK LU PK PABattery Life (Estimate) 75,000 75,000 75,000 75,000Power Supply 6 "AA" "6 "AA" 6 "AA" 6 "AA"Low Battery Indication Yes Yes Yes YesHard Wiring Available Yes Yes Yes Yes
Users & Codes LK LU PK PA# of Users Supported per Lock 100 500 500 500# of Users in Database N/A 10,000 10,000 10,000Audit Trail 15 1000 1000 1000Possible Combinations 1,100,000 1,100,000 1,100,000 1,100,000Code: Number of Digits 1 to 6 Digits 1 to 6 Digits 1 to 6 Digits 1 to 6 DigitsMaster Code Yes Yes Yes YesEmergency Code Yes Yes Yes YesSupervisory Code Yes Yes Yes YesOne Time User Code Yes Yes Yes Yes
Features LK LU PK PAReal Time Clock with Date & Time - Yes Yes YesUp to 8 Time Zones per Lock - Yes Yes YesHolidays (16 Single & 16 Blocked) - Yes Yes YesDaylight Savings Time - Yes Yes YesAuto Unlock - Yes Yes YesAuto Unlock with First In - Yes Yes YesMaintain Unlock Code (Passage) Yes Yes Yes Yes
Adjustable Features LK LU PK PAUnlock Time Adjustability 1-99 Sec 1-99 Sec 1-99 Sec 1-99 SecAudible Keystroke Beep Available Yes Yes Yes -Remote Unlocking Yes Yes Yes Yes
Specify Note Example
Profile with 10 Line Cylindrical Lock
Prefix Signature Cylinder 10-
Series 10G77 10-10G77
Trim & Tech LK, LU, PK or PA x Lever Design 10-10G77-LKL
Finish Specify Finish 10-10G77-LKL-26D
Profile with 8200 Series Mortise Lock
Prefix XC Key System 11-
Series/Function 8276 11-8276
Trim & Tech LK, LU, PK or PA x Lever Design 11-8276-PAJ
Finish Specify Finish 11-8276-PKJ-26D
Hand Specify Hand 11-8276-PKJ-26D-RH
Profile with 80 Series Exit Device
Prefix Fire Rated 12-
Technology LU 12-LU
Series/Function 8877 12-LU8877
Trim ETJ 12-LU8877 x ETJ
Hand RHRB 12-LU8877 x ETJ x RHRB
Finish Trim/Exit 12-LU8877 x ETJ x RHRB x 26D/32D
Door Size 36” 12-LU8877 x ETJ x RHRB x 26D/32D x 36”
Feature Comparisons
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
4 An ASSA ABLOY Group company
Profile Series v.G1.5Stand-Alone Access Control ProductsBored Locks
1-800-727-5477www.sargentlock.com
Profile Series v.G1.5Stand-Alone Access Control ProductRF Technology & SofLink™ Features
1-800-727-5477www.sargentlock.com
52-2551 RF FobInside Escutcheon
RF technology offers stand-alone access control enhancement by allowing the user to remotely control the lock by means of a hand-heldtransmitter (RF Fob).
The Profile Lock is easily programmed for three primary RF actuation modes: Passage, Standard or Panic. RF Technology is an additionalmeans of operating the lock by direct keypad code entry or proximity credential presentation.
Primary modes of RF TechnologyPassage: Remotely toggle (lock/unlock) the unit which remains locked/unlocked until the RF Fob is pressed again. Convenient applications: To unlock doors for extended periods of time; employee entrances, office suites, etc.
Unlock/Relock: Remotely unlock for a defined period of time (1 to 99 seconds) and then automatically relock at the end of that timeperiod. Typical applications: Security entrances, guard stations, anywhere an electric strike is not feasible and/or an audit trail is desired.
Panic: An RF Fob set as a “Panic User” can be used to quickly and easily lock entry doors remotely during emergency situations to prevententry by intruders. Remains locked until reset by Master Code.
Outside Escutcheon
Features of the RF Technology
• RF technology with v.G1.5 is available in keypad as G1-TU, keypad & proximity as G1-TP and with proximity as G1-TA models
• UL and cUL Listed for fire doors
• Typical operating distance of 35 to 75 feet on inside of door; 10 to 25 feet on outside of door*
• Profile Series v.G1.5 is ideal for retrofit applications: Minimal door prep with no frameprep, wiring or power supply needed
• Multiple RF Fobs may be programmed into a single lock
• LED indicator on inside escutcheon shows when RF lock is actuated
• Cylindrical, Mortise and Exit Device locking types available
• All Profile Series v.G1.5 finishes and levers available, including Coastal Series
• Supported by SofLink Plus™ w/ SofLink PDP™ application software
To Order
Note: G1.5 products are ordered as G1products. Specify the desired technology:
G1-TU 2000 Users w/ Keypad only withRF Technology
G1-TP 2000 Users w/ Keypad andProximity with RF Technology
G1-TA 2000 Users w/ Proximity only and RF Technology
ActuationIndicator
NOTE: RF Fob sold separately
BoredShown
SofLink Plus w/ SofLink PDP Features• Access the database(s) from multiple PC
locations• Auto Backup prompts• System Setup Task List Guide• SofLink Plus™ w/ SofLink PDP™ Software
is required for programming time zones,holidays, auto unlock and proximity onlyG1-PA and G1-TA locks
• User name import function from database
• Auto unlock with or without “first-in” authorization
• Access level oriented format• PDA (wireless) communication to and
from lock• SofLink Plus™ w/ SofLink PDP™ Access
Control Management software allowssimple programming and interrogationusing PDA (wireless) data transfer
• PDA infrared communication performedon outside of door
• First-in Auto-Unlock by specified users• "Forced" Master Code from factory
default• For other formats, consult factory• New proximity enrollment station option• Temporary Codes by number of uses
(1-500), start-and-stop dates or total daysafter first use (24 hour specific)
* Operating distance may vary depending on building construction
Note: RF Technology (G1-TU, G1-TP, G1-TA) will provide approximately4-1/2 months of battery life
Profile Series v.G1.5Stand-Alone Access Control ProductsAccessories
1-800-727-5477www.sargentlock.com
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
6 An ASSA ABLOY Group company
Profile Series v.G1.5Stand-Alone Access Control Products8200 Series Mortise Locks
1-800-727-5477www.sargentlock.com
The v.G1.5 Profile Series 8200 motorized mortise lock product has a clean, crisp design and is available in thirteen lever designs and tenhardware finishes. The Profile Series v.G1.5 mortise locks are ideal for business and facility entrances, computer room areas, telephonerooms, health clubs, and child care facilities. The 8200 series mortise lock with dead bolt (G1-8276-LU, G1-8277-PK) is an excellent choice forrest room doors providing privacy when the dead bolt is thrown.
8276 Profile Series Lockwith Deadbolt andCylinder
Entry Lock Functions
8278 Profile Series Lockwith Cylinder
8279 Profile Series Lock8277 Profile Series Lockwith Deadbolt
• Meets ANSI A156.13 Grade 1 requirements
• Motor driven mortise lock
• 3/4" stainless steel, anti-friction reversible latch
• For 1-3/4" (44mm) thick door standard. Consult factory for other thicknesses
• 1" throw investment cast hardened stainless steel deadbolt
• Stainless steel non-handed deadlocking latch
• Handed, easily field reversible without opening lockbody
• Lever trim through-bolted for increased security and durability
• Operates with 6 “AA” batteries (included)
• Typical 75,000 operations per set of batteries
• Cylinder override for 8276 and 8278 models, Size 43-standard andremovable core (1-3/8" [35mm] length of shell)
• Not available with SC- or SE- prefixes
Inside/Outside Escutcheon
13-1/2" (343mm)
3-3/4"(95mm)
Outside Shown
*U.S. Patent No. D470,033S
82243 Dorm Room Anti-Lock with Deadboltand inside lever switchNote: Same as 8276 with these variations
• Dorm room application for studentsusing proximity cards
• Prevents students from lockingthemselves out of dorm rooms
• Only available with v.G1.5Technology
• Requires controller to be configuredfor Dorm Room application atfactory
• Available with PK and PA versions
• Keys/buttons with double shot moldconstruction prevents wear
• Zinc die cast
• Operating temperature -40°F (-40°C) to 135°F (57°C)
• LEDs indicate valid/invalid entries
• Projection at bottom 5/16" (8mm) less lever
• Projection at top 1-5/8" (41mm)
• Key outside retracts andprojects deadbolt andretracts latchbolt
• Lever inside retracts latchboltand deadbolt simultaneouslywhen deadbolt is projected
• Lever outside rigid exceptwhen in “passage” mode orwith valid user credential
• Lever outside lockselectrically with deadboltprojected. Master Code &Emergency Code will allowlever outside to retractlatchbolt & deadbolt
• Thumb turn retracts and projects deadbolt
• Auxiliary deadlatch
Note: Same as 8276 without cylinder
• Lever inside retracts latchboltand deadbolt simultaneouslywhen deadbolt is projected
• Lever outside rigid exceptwhen in “passage” mode orwith valid user code
• Lever outside lockselectrically with deadboltprojected. Master Code &Emergency Code will allowlever outside to retractlatchbolt & deadbolt
• Thumb turn retracts and projects deadbolt
• Auxiliary deadlatch
• Key outside retracts latchbolt
• Lever inside retracts latchbolt
• Lever outside rigid exceptwhen in “passage” mode orwith valid user credential
• Auxiliary deadlatch
• Deadlocking latch
Note: Same as 8278 without cylinder
• Lever inside retracts latchbolt
• Lever outside rigid exceptwhen in “passage” mode orwith valid user credential
• Auxiliary deadlatch
Mechanical Features
8
Profile Series v.G1.5Stand-Alone Access Control Products4293 Wall Prox Unit
1-800-727-5477www.sargentlock.com
An ASSA ABLOY Group company
SARGENT’s 4293 stand-alone prox reader offers all of the expanded capabilities of our Profile Series v.G1.5 hardware self-contained in ahard-wired reader.
The 4293 Wall Prox unit is managed from a personal computer using SofLink Plus Version 4.0 or higher software. The 4293 Wall Prox unit isequipped with IR (infrared) communications which allow the unit to be programmed with SofLink PDP software. In addition, the 4293 WallProx unit can be programmed with the unit’s keypad.
No separate controller is needed for the 4293 Wall Prox, eliminating the need to run cables from a reader to a controller. The independentunit includes built in HID proximity technology, a keypad, and the controller.
Features• 12VDC or 24VDC, 70mA hard-wired Proximity reader
• 2 Amp main lock relay contact rating
• 2,000 users and 2,000 audits
• Database capacity of 20,000 individual users
• Weather Resistant electronics (gasket included)
• Supports all HID 125 KHz Wiegand formats (up to 40 bit) by Keypad Presentation or when using proximity enrollment station ES-G1 with SofLink Plus 5 software
• Supports 26, 34, & SARGENT 1000 (33 bit) HID formats with SofLink PlusTM version 4.0 or higher software programming
• Separate (auxiliary) 2 amp relay to signal alarm shunt, propped or forced door (must use door status switch)
• Audible Alert for propped or forced door
• Can locate proximity antenna up to 10’ from keypad/controller
• Glass mounting kit provided
Access System Requirements
Dimensions:L: 5-1/4”W: 2-3/4”D: 1-5/8"
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
Software Requirements:• SofLink Plus™ Version 4.0 or higher software
• SofLink PDP software
Hardware Requirements:• Windows 2000/XP (to include all subsets)
• IBM-compatible Pentium-class computer
• 30MB available hard disk space
• VGA monitor
• CD-ROM drive
• Mouse
• Personal Digital Assistant (PDA). See compatibility chart on p.9
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
9
Profile Series v.G1.5Stand-Alone Access Control ProductsSofLink Plus™ Access ControlManagement Software
1-800-727-5477www.sargentlock.com
SofLink Plus™ w/ SofLink PDP™ Access Control Management SystemThe SofLink Plus w/ SofLink PDP Access Control Management Software allows simple programming and interrogation of the Profile Seriesv.G1.5 access control products. This software provides the means for fast, convenient assignment of access levels, doors, users, time zones andmanagement of multiple doors with full audit trail capability. Communication between the computer and lock controller is via PDA that allowsquick and efficient program transfer and audit trail retrieval.
• Password protected• Supports 2,000 users per lock• 20,000 user name database• 2,000 event transaction history –
audit trail to include user entry, date,time, user number, access denied,passage on, passage off, auto unlock,time zone denied, print, audit trailrelease, program mode, programmode denied, etc.
• Master code entry at keypad orpresentation of “Master” or“CommEnable” proximity credential at lock initiates PC downloadprogramming
• User friendly help feature• Extensive report generating feature• Directly supports 26, 33 and 34 HID 125kHz Wiegand bit
formats or all (up to 40 bit) formats when using the proximityEnrollment Station.
• For directly supporting 35 Bit Corporate 1000 Format or otherformats, consult factory
• Designed for operation with Personal Digital Assistant (PDA)running Palm OS®
• PDA provides convenient (wireless) means of transferring doorinformation to and from lock using SofLink Plus™ w/ SofLink PDP™ software
• Capable of up/down loading door information for up to 50 doorsNOTE: Number of stored files is dependent on the amount of non-related SofLink Plus™ w/ SofLink PDP™ software applicationsand data (e-mail messages, address data, to do items, memos, etc.)loaded on the PDA.• Five additional compatible PDAs• Access the database(s) from multiple PC locations• New, more detailed reporting• Auto Backup prompts• "User-Friendly" System Setup Task List Guide• Enable/Disable user capability• Auto Unlock with or without “first in” authorization• First-in Auto-Unlock by specified users*• Temporary Codes by number of uses (1-500),
start-and-stop dates or total days after first use (24 hour specific)*
• "Forced" Master Code (from Factory Default)*• Multiple Supervisory users*• Allows customized access levels managed at PC• User name import from an external database• Easy to follow data entry• Real time clock with date and time• Eight different time zones per lock• Holidays (16 single days and 16 blocked)• Forced/Propped Door log events - harness required (option)• Daylight savings time
*v.G1.5 controller also required
• 20,000 users (up from 10,000)• Use of two new Palm PDAs (Zire 31 & Zire 72)• Access the database(s) from multiple PC locations• New, more detailed reporting• Auto Backup prompts• "User-Friendly" System Setup Task List Guide• Enable/Disable user capability• Use of proximity Enrollment Station • "Forced" Master Code (from Factory Default)
v.G1.5 controllers WITH SofLink Plus 5 softwareprovide these additional features• First-IN Auto-Unlock by specified user
• Temporary Codes by number of uses (1-500), start and stop datesor total days after first use (24 hour specific)
• “Forced” Master Code (from Factory Default)
• Multiple Supervisory users
v.G1.5 controllers WITHOUT SofLink Plus 5 softwareprovide these additional features• “Forced” Master Code (from Factory Default)
• Multiple Supervisory users
SofLink Plus™ w/ SofLink PDP™ FeaturesSofLink PLus 5 provides existing v.G1 and 4293 Wall Proxusers with these additional features:
An ASSA ABLOY Group company
CD-SLP5
SofLink Plus 5.0 withSofLink PDP 4.0
Hardware Requirements
• Windows 2000/XP (to include all subsets)
• VGA monitor
• CD ROM drive
• Instruction Manual included
• Personal Digital Assistant (PDA)
Catalog #PDA-Z21 - Palm Zire 21 PDA Works with SofLink Plus 3.0 and above.
Catalog #PDA-Z31 - Palm Zire 31 PDA Works with SofLink Plus 5.0 and above.
Note: For a complete list of compatible PDA models, visit www.sargentlock.com.
Profile Series v.G1.5Stand-Alone Access Control ProductsAccessories
1-800-727-5477www.sargentlock.com
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
10 An ASSA ABLOY Group company
Profile Series v.G1.5Stand-Alone Access Control ProductsAccess Credentials
1-800-727-5477www.sargentlock.com
SARGENT HID ProxCard II™
• Site Code 20• Proximity ID#’s determined & controlled
by SARGENT• 26 Bit Format, HID Coded Wiegand
Output 125 kHz• Dimensions: 2-1/8" x 3-3/8" (54mm x 86mm)• Thickness: .070" nom. (1.8mm)• Cards ordered individually***
(Min. Order is 25 Cards)• Cat # PCH-L70 for SARGENT logo on card• Cat # PCH-B70 for Blank (white) card
PF SARGENT ProxKey II™
• Site Code 20• Proximity ID#’s determined & controlled by SARGENT• 26 Bit Format, HID Coded Wiegand Output 125 kHz• Dimensions: 1-29/32" x 29/32" x 11/32" (48mm x
23mm x 9mm)• Includes Keyring• SARGENT ProxKey II™ ordered individually***
(Min order is 25 ProxKey II™)• Catalog # PF for SARGENT ProxKey II™
ISO Prox Card II™ (Printable Card)
• Site Code 20• Proximity ID#’s determined & controlled
by SARGENT• 26 Bit Format, HID Coded Wiegand
Output 125 kHz• Dimensions: 2-1/8" x 3-3/8" (54mm x 86mm)• Thickness: .031" nom. (.8mm)• Blank card can be printed with customer’s
text and graphics - by others• Cards ordered individually***
(Min order is 25 Cards)• Cat # PCH-L30 for SARGENT logo on card • Cat # PCH-B30 for Blank (white) card
MicroProx™ TagThe MicroProx™ Tag is a coin-sized(disk-shaped) transponder that providesthe ability to add HID proximity technologyto a device. The MicroProx™ Tag has anadhesive backing which allows it to besecured to any non-metallic object.
DuoProx™ Card
• Multiple Technology Proximity Cards -DuoProx™– dual technology - proximity &magnetic stripe
• DuoProx™ cards with unique site codes forhigher level of security (SARGENT 1000)are available
• Contact Factory for specifications,options and pricing
• Cards ordered individually***(Min order is 100 Cards)
*** Products are ordered individually, Ordered Quantity is thenumber of individual items to be shipped. If a Qty of 25 is ordered - 25 individual items will be shipped (Note: Min Order Requirements)
1000
Credential Features
• Easily Secured To: Employee badges • PDAs • Magnetic stripecards • Cell phones
• 26 Bit Format, HID Coded Wiegand Output 125 kHz• Proximity ID# marked on each Tag• Gray color with HID Logo• Dimensions: 1.285" Dia. x 0.070" (32.6mm x 1.78mm)Two Versions available:
• Catalog # MPT- Site Code 20- Proximity ID#’s determined & controlled by SARGENT- MicroProx™ Tag ordered individually***- Min. order is 25 MicroProx™ Tag
• Catalog # MPT-C- Site Code - requested by customer- Proximity ID#'s requested by customer- MicroProx™ Tag ordered individually***- MicroProx Tag with custom site code, consult factory for
minimum quantities NOTE: The MicroProx™ Tag should be attached to magnetic stripecards so that contact with the magnetic card reader is avoided.
ProxCard II, DuoProx™, Micro-Prox™ and ProxKey IIare trademarks of HIDCorporation
PF-C Custom ProxKey II™
• Site Code - requested by customer• Proximity ID#'s requested by customer • 26 Bit Format, HID Coded Wiegand Output 125 kHz• Dimensions: 1-29/32" x 29/32" x 11/32" (48mm x 23mm x 9mm)• Includes Keyring• PF-C Custom ProxKey II™ ordered individually***
(Min order is 100 Custom ProxKey II™)• Catalog # PF-C for Custom SARGENT ProxKey II™
• 26 to 39 bit Wiegand format available (Consult factory for details)
• Provides higher level of security when combined with keypadoperation
• HID-based proximity cards, fobs or tags
• Allows integration into existing facilities with HID-based technology
• SARGENT standard credentials are 26 Bit Wiegand format, Site Code 20 and Proximity ID assigned by SARGENT
• Custom credentials available with customer assigned Site Code and Prox ID#'s
HID technology allows Access Control software to read other formatsprovided site code is known. For a higher level of security, custom cards, fobs or tags with unique site codes are available. Consult factory.
Note 2: SofLink Plus™ w/ SofLink PDP™ software directly supports 26, 33 and 34 HID 125 kHz Wiegand bit formats or all (up to 40bit) when using the Enrollment Station, ES-G1. To directly support other formats (such as 35 bit HID Corporate 1000 format),consult factory.
Note 1: Profile Series v.G1.5 will support all HID bit formats when proximity credentials are programmed directly into keypad(Presentation Method)
Profile Series v.G1.5Stand-Alone Access Control ProductsAccessories
1-800-727-5477www.sargentlock.com
Profile Series v.G1.5Stand-Alone Access Control ProductsSARGENT BioFob Security Device
1-800-727-5477www.sargentlock.com
11An ASSA ABLOY Group company 3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
The BioFob™ Security Device is the first handheld, wireless, biometric device providing both physical and logical access. This self-containedunit performs fingerprint sensing, image processing, storage and matching to activate the RFID (HID or Indala) and Bluetooth signals. Thesesignals unlock SARGENT’s Profile Series Locks, existing HID or Indala readers and encrypted computer systems. BioFob is the perfectbiometric solution for your existing security system.
BioFob Features for BF1, BF2, BF3 & BF4• Fingerprint templates are sensed, processed, stored and matched within the BioFob• No centralized biometric database is required solving many privacy concerns• Communicates wirelessly to access points or to specified authorities using existing RF infrastructures making it easy to
“overlay” this biometric solution onto existing security systems• Provides biometric security for physical and logical access
• Physical access - The BioFob can be configured with HID or Indala proximity credentials for use with any Profile Series (HID) proximitylock, 4293 (HID) wall prox or other HID and Indala readers
• Logical access - The BioFob is capable of computer and network logon along with other various Information Technology applications via third party software
• Releases signal after verifying user's identity• Enrollment Station Software is required to enroll BioFob(s)
Power Battery type: CR2 lithium cell (included)Battery life: Approximately 1 year; 5 operations per day.
Interfaces User interaction: 3 LEDs (red, yellow, green), 1 push button (power)RF options: Low-frequency RFID, HID and Indala compatible (125 kHz)and Bluetooth™ (2.4 GHz)
Environment –Operating temperature: +14° F to +140° F; (-10° C to +60° C)–Storage temperature: -40° F to +185° F; (-40° C to +85° C)–Operating humidity: 90% noncondensing
BioFob Specifications
BioFob being presentedto Profile Series Lock
BioFob Security Device
Configuration Module (USB Dongle) - BF7, BF8, BF9 and BF10A configuration module (also known as a dongle) attaches to the computer's USB port. It is required to encode an uncoded Biofob (BF4) or recode any BioFob with a Site Code & Proximity ID. The configuration modules are available with either HID or Indala proximity ID's with either 25 or 100 proximity ID's per module.
All BioFobs and modules are 26 Bit Format. For other formats, please consult factory.
BFES BioFob Enrollment StationThe Enrollment Station is required to activate a BioFob Security Device for every individual. An individual’s fingerprint template is transmitted wirelessly between the BioFob and the computer’s Bluetooth adapter. The Enrollment Station software is used to configure the BioFob for a user.
BFES Enrollment Station includes:
System Requirements for the Enrollment Station Software and Bluetooth™ AdapterMinimum software and hardware requirements:
• One (1) CD-ROM containing the Enrollment Stationsoftware - Model BT
• One (1) Operating Manual and Quick Start Guide
• One (1) CD-ROM containing the driver software andprotocol stack for the Bluetooth™ adapter
• One (1) USB attachable Bluetooth™ adapter
• Microsoft Windows 2000 or Microsoft Windows XP• 64 megabytes of RAM• 20 megabytes of available hard drive space
• One available USB port• 800x600 minimum resolution
BF6 Bluetooth Adapter and Driver Software Replacement Package includes:• CD-ROM containing the driver software and protocol stack for use with the Bluetooth™ adapter• One (1) USB attachable Bluetooth™ adapter
The SARGENT BioFob was developed in partnership withPrivaris, Inc., a technology companydedicated to solving security andprivacy concerns for governmentand commercial applications.
Profile Series v.G1.5Stand-Alone Access Control ProductsAccessories
1-800-727-5477www.sargentlock.com
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
12 An ASSA ABLOY Group company
Profile Series v.G1.5Stand-Alone Access Control ProductsSARGENT BioFob Security Device
1-800-727-5477www.sargentlock.com
Note: All BioFobs and Configuration Modules are 26 Bit Format. For other formats, consult factory.
General InformationThe Proximity ID# is assigned to a Proximity Credential (e.g., BioFob). This number identifies a Proximity Credential to a user within a givenSite Code.A Site Code is a number established by either SARGENT (e.g., BF1 BioFob) or the end-user. The Site Code, established by the Bit Format, is anumber between 1 and 255 for a 26 Bit Format configuration. The Site Code assigned to a group of proximity control products (e.g., ProfileSeries) and Proximity Credentials (BioFob, etc.) must be identical for the two to interact. Proximity ID#'s should not be used more than oncewithin a Site Code for security reasons.The Bit Format, part of the coding configuration within a Proximity Credential (BioFob) is established and can only be changed by themanufacturer. A 26 Bit Format of a Proximity Credential (BioFob) has 65,535 ID#’s available. The 26 Bit Format for Site Codes and ProximityID#'s creates over 16.5 million possible Site Codes/ID#s per BioFob.
BioFob Security Devices
Products # Note How to Order- Site Code 20
BF1 - Proximity ID#’s determined & controlled by SARGENT Qty 1 BF1- 26 Bit Format, HID Coded Wiegand Output 125 kHz
- Site Code - requested by customer Qty 1 BF2BF2 - Proximity ID#'s requested by customer Site Code XXX
- 26 Bit Format, HID Coded Wiegand Output 125 kHz Prox ID # XXXXX
- Site Code - requested by customer Qty 1 BF3BF3 - Proximity ID#'s requested by customer Site Code XXX
- 26 Bit Format, Indala Coded Wiegand Output 125 kHz Prox ID # XXXXX
- Uncoded BioFob BF4 - Site Code, Proximity ID# & Bit Format to be assigned Qty 1 BF4
- Can be coded using Configuration Modules - BF7, BF8, BF9 or BF10
Configuration Modules for Encoding BioFobs
Products # Description Includes: How to OrderTo encode an uncoded Biofob (BF4) Customer defined Qty 1 BF7
BF7 or recode any BioFob with a - 1 Site Code Site Code XXX Site Code & HID Proximity ID# - 25 HID Proximity ID#’s Prox ID #’s XXXXX-XXXXX
To encode an uncoded Biofob (BF4) Customer defined Qty 1 BF8BF8 or recode any BioFob with a - 1 Site Code Site Code XXX
Site Code & HID Proximity ID# - 100 HID Proximity ID#’s Prox ID #’s XXXXX-XXXXX
To encode an uncoded Biofob (BF4) Customer defined Qty 1 BF9 BF9 or recode any BioFob with a - 1 Site Code Site Code XXX
Site Code & Indala Proximity ID# - 25 Indala Proximity ID#’s Prox ID #’s XXXXX-XXXXX
To encode an uncoded Biofob (BF4) Customer defined Qty 1 BF10 BF10 or recode any BioFob with a - 1 Site Code Site Code XXX
Site Code & Indala Proximity ID# - 100 Indala Proximity ID#’s Prox ID #’s XXXXX-XXXXX
Enrollment Station, Bluetooth Adapter, Drivers and Software
Products # Note How to Order- Enrollment Station is required to enroll an individual’s fingerprint
BFES template into a BioFob and to activate it Qty 1 BFES- Includes all the components of BF6- An enrollment station can be used an unlimited number of times
- USB Bluetooth Adapter BF6 - Driver software Qty 1 BF6
- BF6 Components are included in the BFES Enrollment Station
Profile Series v.G1.5Stand-Alone Access Control ProductsAccessories
1-800-727-5477www.sargentlock.com
Profile Series v.G1.5Stand-Alone Access Control ProductsAccessories
1-800-727-5477www.sargentlock.com
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
13An ASSA ABLOY Group company
3267 Replacement Parts
52-0255 Plug-In Wall Transformer• Output 16.5 VAC, 2.4 Amps
• UL/cUL Listed
• Provides input power to Model3267 Remote Power supplymodule
52-0258• Cable Assembly-Power Supply to Power Transfer
• 12' (3.6m) shielded cable from the power to the power supply
52-2498• 9 VDC, 700 ma Power Supply circuit board
• Replacement circuit board assembly
52-0256 Gel Cell Battery• Optional for 3267 Remote Power supply
• Provides continuous operation of Profile Series v.G1.5 inthe event of a power failure
• 12 VDC 1.2 A/Hr rating
• 10,000 cycles typical in the event of power failure
• When ordering harness only, use 52-3010
• For ElectroLynx doors - QC8electric hinge is required
• For non-ElectroLynx doors -requires raceway with wire harnessthrough the door and powertransfer
4 Wire Concealed Circuit Hinge forRemote Power Only (McKinneyCC4).
6 Wire Concealed Circuit Hinge for Remote Power andRemote Unlocking Options (McKinney CC6)
3267 Remote Power• Provides a filtered and regulated 9 VDC remote
power for Profile Series v.G1.5 locks
• Each unit can supply power to 2 Profile products
• Optional 12 VDC Gel Cell battery allows forcontinuous operation in the event of a power failure.(Strongly recommended for applications withoutcylinder over-ride to prevent lock-out)
• Requires manufactured door with ElectroLynx orraceway through the door for hard-wiring*
Reference template list below for correct preparation of non-ElectroLynxdoors.
4540 – Bored Lock4541 – Mortise Lock4542 – Rim and Mortise Exits
Includes:• Plug-In Wall Transformer (52-0255) and (52-0258) 12' (3.6m) of shielded
wire for connection between power transfer and power supply.(Maximum length of 50' (15.2m) recommended)
* Recommended for new opening. Retrofit application may require surface mountedwire mold and transfer loop by others.
91- Prefix Remote Power & Unlocking Wiring Harness• Wire harness for Remote Power and Remote Unlocking
(request to enter)
• Packed with lock assembly
Profile Series v.G1.5 Exit Device Upgrade Kit For:SARGENT 80 Series Rim Exit Device (8877/8878)Mortise Exit Device (8977/8978)
The Escutcheon/Electronics kits are available as single or three packs. Whenordering specify kit number and finish (231LK x 26D)
1 Pack Kit P/N 3 Pack Kit P/N Description
231 LK 233 LK Keypad Only (100 User\15 Audit Capability)
231 G1-LU 233 G1-LU Keypad Only (2000 User\2000 Audit Capability)
231 G1-PA 233 G1-PA ProximityOnly (2000User\2000 Audit Capability)
231 G1-PK 233 G1-PK Proximity & Keypad(2000 User\2000 Audit Capability)
231 G1-TU 233 G1-TU Keypad Only (2000 User\2000 Audit Capability)with RF Technology
231 G1-TA 233 G1-TA Proximity Only (2000 User\2000 Audit Capability)with RF Technology
231 G1-TP 233 G1-TP Proximity & Keypad(2000 User\2000 Audit Capability)with RF Technology
Trim Kits are the motorized exit trims that are necessary to be used with theProfile Upgrade Kits to convert an existing exit device.
Trim Kit P/N Description
777-8 8800 Series Rim Exit Device w/ Cylinder Override
778-8 8800 Series Rim Exit Device w/o Cylinder Override
777 8900 Series Mortise w/ Cylinder Override
778 8900 Series Mortise Exit w/o Cylinder Override
Exit Device Profile Upgrade
DM- Prefix Forced/Propped Door Harness• Wire harness for Forced/Propped door
• Packed with lock assembly
• When ordering harness only, use 52-3409
• For ElectroLynx doors - QC4A electric hinge is required; QC12 electric hinge is required when used with Remote Power and/or Remote Unlocking
• For non-ElectroLynx doors - requires raceway with wire harness through the door and power transfer
4 Wire Concealed Circuit Hinge for Forced/Propped DoorOnly (McKinneyCC4).
8 Wire Concealed Circuit Hingefor Forced/Propped Door andRemote Power/Remote Unlocking(McKinney CC8)
• Door Status switch required
Hardwiring Made Easy™
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
14
Profile SeriesStand-Alone Access Control ProductsAccessories
1-800-727-5477www.sargentlock.com
An ASSA ABLOY Group company
52-2593 Protective Shroud• Provides weather protection for
outside escutcheon
• Cover and hinge molded of toughpolycarbonate
• Stainless steel torsion spring maintainscover in closed position
• Easily lifts for access to keypad
• Comes with mounting hardware and gasket
• Fast, easy installation
• Order separately
52-2847 Conduit• Provides weather protection inside of door
• Constructed of durable ABS material
• For non-fire rated exterior applications only
• Included with product
82-0500
For use with8200 MortiseEscutcheon
68-1400
For use with8800 or 8900
ExitEscutcheon
Weatherseal Gasketing
52-0263
For use withET Trim
10-0469
For use with10G77
CylindricalEscutcheon
• Provides sealing between outside escutcheon and door for exterior applications
• Gasketing (included) recommended for non-fire rated exterior applications
Keypad Assemblies
52-2704 52-2706
Assembly Products LU PK* PA* LK G1-LU G1-PK* G1-PA* G1-TU G1-TP G1-TA
Controller Bored 52-2446 52-2453 52-2453 52-2439 52-2733 52-2734 52-2734 52-2735 52-2736 52-2736
Mortise 52-2447 52-2454 52-2453 52-2440 52-2783 52-2784 52-2784 52-2785 52-2786 52-2786
Exit 52-2448 52-2455 52-2455 52-2441 52-2783 52-2784 52-2784 52-2785 52-2786 52-2786
Keypad All 52-2432 52-2432 +52-2431 52-2432 52-2704 52-2704 +52-2706 52-2704 52-2704 +52-2706
• Assemblies includecircuit board andhousing
• Batteries notincluded
• v.G1.5 controllersare labeled "G1.5"
Controller Note: Replacing existing G1 controllers with G1.5controllers provides the following new features:
• "Forced" Master Code change from factory default
• Multiple Supervisory users
• First-in Auto-Unlock by specified users (SofLinkPlus 5.0 required)
• Temporary Codes by number of uses (1-500),start-and-stop dates or total days after first uses(SofLinkPlus 5.0 required)
Enrollment Station Catalog #ES-G1• Enrolls HID 125 kHz
Wiegand output (up to 40-bit format) proximitycards into software whenbit format and/or sitecode is unknown
• PC Serial com portrequired
• SofLinkPlus 5.0 or higher required
4293
52-2069 Infrared Portable Printer• Used to download the user numbers and
transaction types from lock (LK only)
• Operates with 4 “AA” batteries (included)
v.G1.5 Series Controllers
Dorm Room Anti-Lock Product
Controller Assy 52-3413
Keypad Assy, G1-PK 52-2704
Keypad Assy, G1-PA +52-2706
*FCC approved
+Proximity only, no keypad
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
15
Profile Series v.G1.5Stand-Alone Access Control ProductsLever Trim Designs
1-800-727-5477www.sargentlock.com
An ASSA ABLOY Group company
• Lever: L-Solid forged or cast
Profile Series v.G1.5 products are available with lever designs identical to levers offered on mechanical hardware to introduce uniformitythroughout a facility. Lever projection from door surface varies with lock type.
L Lever Design
P Lever Design
• Lever: L–Solid Cast
Y - Yarmouth
• Lever: P–Solid Cast
B Lever Design
J Lever Design
• Lever: B–Solid Cast
G - Gulfport
• Lever: J–Solid Cast
J lever – not availableInterchangeable Core
• Lever: G–Solid Cast• Must specify hand when ordering
• Lever: Y–Solid Cast• Must specify hand when ordering
v.G1.5 10 Line Lever Locks v.G1.5 8200 Mortise Levers and v.G1.5 80 Series ET Levers
F Lever Design
J Lever Design
• Lever: F-Solid forged or cast
B Lever Design
• Lever: J-Solid bar stock
A Lever Design
E Lever Design
• Lever: A-Solid forged or cast
• Must specify hand whenordering
L Lever Design
• Lever: E-Solid forged or cast
• Lever: B-Solid forged or cast
W Lever Design
P Lever Design• Lever: P-Solid forged
or cast
• Lever: W-Solid bar stock
Coastal Series™ for v.G1.5 8200 Mortise Locks and 80 Series Exits
• Must specify hand when ordering
• Must specify hand when ordering
S - Sanibel™
C - Coronado™
R - Rockport™
Y - Yarmouth™
G - Gulfport™
Coastal Series™ for v.G1.510 Line Locks
• Solid Cast Brass
• Must specify hand when ordering
*Similar lever styles available for Cylindrical lock version.
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
16
DL Series Tubular LockMetro Elements™ Levers
1-800-727-5477www.sargentlock.com
Rialto Series
MO
ML
MQ
MR
MT
MM
MC
MD
MJ
MP
Centro Series Aventura Series
MN
MH
MK
MS
MU
MV
Odéon Series
An ASSA ABLOY Group company
Notting Hill Series
MA
MB
ME
MF
MG
MI
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
17
Profile Series v.G1.5Stand-Alone Access Control ProductsPrefixes
1-800-727-5477www.sargentlock.com
An ASSA ABLOY Group company
Prefixes Available
3 Stainless steel hubs for institutional specifications (mortise locks only)
10 SARGENT Signature Key System
10-UL SARGENT Signature Key System Meeting UL437 (mortise and rim cylinders only, not available with Cylindrical Locks)
11 XC Key System (not available with 10-, 1-UL, 22-, 60-, 63-, 64-, SC- or SE- prefixes)
12 UL Fire Label Exit hardware (exit devices only)
16 Cylinder Lockdown, (exit devices only) not available with 12-
19 Pushbar without Lexan touchpad (exit devices only)
21 SARGENT Lost Ball Construction Key system
22 SARGENT Split Key System (existing systems only)
23 Flat 4-7/8" (124mm) ANSI strike (mortise) 3-3/4" (95mm) backset (cylindrical locks only)
25 5" (127mm) Backset (cylindrical locks only)
28 ANSI strike #808 (cylindrical locks only)
30 0G77 lever to accept Schlage cylinder – no cylinder provided (cylindrical locks only)
35 Adjustable Front cylinder furnished with lock n/a with removable core (mortise locks only)
36 Six lobe security head screws
37 Spanner head screws
41 3/4" (19mm) throw latch x 2-3/4" (70mm) backset (10G77)
60 SARGENT Removable Disposable Construction Core
63 SARGENT Removable Core cylinder
64 SARGENT Removable Core Construction Core cylinder
65-73 Small Format Interchangeable Core 6 Pin Uncombinated core
65-73-7P Small Format Interchangeable Core 7 Pin Uncombinated core
72 Small Format Interchangeable Core 6 Pin Construction Core cylinder
73 Small Format Interchangeable Core 6 Pin SARGENT 4A, 4B keyways available only for new systems
73-7P Small Format Interchangeable Core 7 Pin SARGENT 4A, 4B keyways available only for new systems
75 Milled Inside lever (mortise) Handicap Warning on inside lever (cylindrical) Tactile Warning (exits)
76 Milled Outside lever (mortise and exits) Handicap Warning on outside lever (cylindrical)
77 Milled both levers (mortise) Handicap Warning on both levers (cylindrical) Abrasive strip on rail, Abrasive coating on lever (exits)
82 SARGENT Keso Security Cylinder (existing systems only)
83 SARGENT Keso Security Removable Core cylinder (existing systems only)
84 SARGENT Keso Security Removable Construction Core cylinder (existing systems only)
91 Power/Remote Unlocking wiring harness
DM Forced/Propped door harness
SC Schlage “C” Keyway cylinder “0” bitted
SE Schlage “E” Keyway cylinder “0” bitted
SG SARGuard antimicrobial clear powder coat (on metal components only)
VA SARGENT V-10 Standard cylinder
VS SARGENT V-10 Standard cylinder unassembled (mortise and exits)
3/10
/06
© S
AR
GEN
T M
anu
fact
uri
ng
Co
mp
any
2006
19
Profile Series v.G1.5Stand-Alone Access Control ProductsFinishes, Handing, How to Order &Shipping Information
1-800-727-5477www.sargentlock.com
An ASSA ABLOY Group company
Lock Shipping Weight Pc. Count/Carton
G1-8276-PK x lever trim (with cylinder) 11.2 lbs (5.1kg) 1/carton
G1-8277-PK x lever trim (no cylinder) 10.7 lbs (4.9kg) 1/carton
G1-8278-PK x lever trim (with cylinder no deadbolt) 11.2 lbs (5.1kg) 1/carton
G1-8279-PK x lever trim (w/o cylinder no deadbolt) 10.7 lbs (4.9kg) 1/carton
G1-LU8877 21.0 lbs (9.5kg) 1/carton
G1-PA8977 23.0 lbs (10.4kg) 1/carton
G1-10G77-PKL 10.7 lbs (4.9kg) 1/carton
How To Order
Shipping Information
Specify Note Example
Bored
Prefix Signature Cylinder 10
Series 10G77 10-10G77
Trim Technology & Lever Design 10-G1-10G77-PKL
Finish Specify Finish 10-G1-10G77-PKL-26D
Mortise
Prefix Signature Cylinder 10
Series/Function 8276 10-8276
Trim Technology & Lever Design 10-G1-8276-PAJ
Finish Specify Finish 10-G1-8276-PAJ-26D
Hand Specify Hand 10-G1-8276-PAJ-26D-RH
Exit
Prefix Fire Rated 12
Technology LU 12-G1-LU
Series/Function 8877 12-G1-LU8877
Trim ETJ 12-G1-LU8877 x ETJ
Hand RHRB 12-G1-LU8877 x ETJ x RHRB
Finish Trim/Exit 12-G1-LU8877 x ETJ x RHRB x 26D/32D
Door Size 36" 12-G1-LU8877 x ETJ x RHRB x 26D/32D x 36"
Dorm Room Anti-Lock (Mortise Only)
Prefix Signature Cylinder 10
Series/Function 82243 10-82243
Trim Technology & Lever Design 10-G1-82243-PKL
Finish Specify Finish 10-G1-82243-PKL-26D
Hand Specify Hand 10-G1-82243-PKL-26D-RH
Handing
Right Hand Door
Left Hand Reverse Bevel
Right Hand Reverse Bevel
RH
RHRB
LHRB
SARGENT Description ANSI/BHMA
US3 Polished brass 605
US4 Satin brass 606
US9 Polished bronze 611
US10 Satin bronze, clear powder coat 612
US10B Oxidized satin bronze oil rubbed 613
10BL Oxidized satin bronze, clear powder coat ——
US15 Satin nickel, clear coated 619
20D Dark statuary bronze, clear powder coat ——
US26 Polished chrome 625
US26D Satin chrome 626
Finishes
Left Hand Door
Zinc levers are plated to match BHMA finish.
LH
2 1-800-727-5477 • www.sargentlock.com
T-Zone Lever LockLever and Rose Designs
Type 161 Cutout
If weather-stripping, acoustical materials or silencers are used on thedoor or frame, care must be taken in the installation so that it will notinterfere with the ease in which the latchbolt enters the strike
• Rose: O - Wrought• Lever: L - Cast
EB Design
• Rose: E - Wrought• Lever: B - Cast
LJ Design
• Rose: L - Wrought• Lever: J - Cast
BP Design
• Rose: B - Wrought• Lever: P - Cast
OL Design
2-3/4"Backset(70mm)
Type 161 cutout
DoorEdge
Note: Any rose and lever on this page can be combined to suit individual taste.
Note: Lever projections shown are for 1-3/4" (44mm) doors and will vary by door thickness.
2-3/
4"(7
0mm
)
4-15/16"(125mm)
2-3/4"(70mm)
1/4"(6mm)
+/-
1/2"
(13m
m)
2-3/
4"(7
0mm
)
5-5/16"(135mm)
3-1/2"(89mm)
1/4"(6mm) +
/-1/
2"(1
3mm
)+
/-1-
13/1
6"(4
6mm
)
1/4"(6mm)
5-1/8"(130mm)
3-1/8"(79mm)
2-3/
4"(7
0mm
)2-
3/4"
(70m
m)
5-3/8"(137mm)
1/4"(6mm) +
/-1/
2"(1
3mm
)
2-3/4"(70mm)
1"(25mm)
2-1/4"(57mm)
2-1/8"(54mm)
1-1/8"(29mm)
3/15/08
Copyrig
ht©2008
SARG
ENTManufacturin
g.Allrightsreserved.
Reprod
uctio
ninwho
leor
inpartwith
outthe
expressw
rittenperm
ission
ofSARG
ENTManufacturin
gisproh
ibited.