specific labs

7/29/2019 Specific Labs

1/31

Om Sakthi

Adhiparasakthi Engineering College, Melmaruvathur

Department of Mechanical Engineering

LIST OF PROGRAM SPECIFIC LABS

UG-program

Sl.No Name of the lab UtilisationAvailable Floor Area

(sq ft)

1.

Engineering Practices Laboratory

a) Welding Lab

b) Manufacturing Technology

Lab

I sem (all branches)

230

345

2.Computer aided drafting and

modeling lab

II sem

(Civil,Mechanical/Chemical)180

3. Manufacturing technology lab-I III sem mech 345

4.Manufacturing technology lab-II

IV sem mech345

5.Computer Aided Machine DrawingLaboratory IV sem mech

180

6.Thermal Engineering-I (HeatEngines) V sem mech 345

7. Dynamics Lab V sem mech 115

8. Metrology and Measurement Lab V sem mech 172

9. CAD/CAM lab V sem mech 180

10. Thermal Engineering Lab-II (HMT) VI sem mech 187

11.Computer Aided Simulation andAnalysis Lab VII sem mech 180

12. Mechatronics Lab VII sem mech 75


2/31

Engineering Practices Laboratory

Subject Code Subject Name Lectures(Periods)Tutorial(Periods)

Practical(Periods)

GE 2116 Engineering Practices Laboratory 0 0 3

List of Experiment/ExercisesGROUP A (CIVIL & MECHANICAL)

I CIVIL ENGINEERING 9 Buildings:

a) Study of plumbing and carpentry components of residential and industrialbuildings. Safety Aspects.

Plumbing Works:a) Study of pipeline joints, its location and functions: valves, taps, couplings, unions,

reducers, elbows in household fittings. b) Study of pipe connections requirements for pumps and turbines.

c)

Preparation of plumbing line sketches for water supply and sewage works. d) Hands-on-exercise: Basic pipe connections Mixed pipe material connection Pipe connections with different joining components.

e) Demonstration of plumbing requirements of high-rise buildings. Carpentry using Power Tools only

a) Study of the joints in roofs, doors, windows and furniture.b) Hands-on-exercise: Wood work, joints by sawing, planing and cutting.

II MECHANICAL ENGINEERING PRACTICE 13Welding:

a) Preparation of arc welding of butt joints, lap joints and tee joints.b) Gas welding practice

Basic Machining:

a)

Simple Turning and Taper turningb) Drilling Practice

Sheet Metal Work: a) Forming & Bending:b) Model making Trays, funnels, etc. (c) Different type of joints.

Machine assembly practice : a) Study of centrifugal pump b) Study of air conditioner

Demonstrationa) Smithy operations, upsetting, swaging, setting down and bending. Example

Exercise Production of heagonal headed bolt.

b) Foundry operations like mould preparation for gear and step cone pulley. (c) Fitting

Exercises Preparation of square fitting and vee fitting models.GROUP B (ELECTRICAL & ELECTRONICS

III ELECTRICAL ENGINEERING PRACTICE 10a) Residential house wiring using switches, fuse, indicator, lamp and energy meter. b) Fluorescent lamp wiring. c) Stair case wiring d) Measurement of electrical quantities voltage, current, power & power factor in

RLC circuit.


3/31

e) Measurement of energy using single phase energy meter. f) Measurement of resistance to earth of an electrical equipment

IV ELECTRONICS ENGINEERING PRACTICE 13 a) Study of Electronic components and equipments Resistor, colour coding measurement

of b) AC signal parameter (peak-peak, rms period, frequency) using CR. c) Study of logic gates AND, OR, EOR and NOT. d) Generation of Clock Signal. e) Soldering practice Components Devices and Circuits Using general purpose PCB. f) Measurement of ripple factor of HWR and FWR.

TOTAL: 45 PERIODS

Reference Books:1. Engineering Practices Laboratory Manual

Text Books:1. K.Jeyachandran, S.Natarajan & S, Balasubramanian, A Primer on Engineering

Practices Laboratory, Anuradha Publications, (2007).2. T. Jeyapoovan, M.Saravanapandian & S.Pranitha, Engineering Practices Lab Manual, Vikas

Publishing House Pvt.Ltd, (2006).3. H.S. Bawa, Workshop Practice, Tata McGraw Hill Publishing Company Limited, (2007).4. A. Rajendra Prasad & P.M.M.S. Sarma, Workshop Practice, Sree Sai Publication, (2002).5. P.Kannai ah & K.L.Narayana, Manual on Workshop Practice, Scitech Publications, (1999).


4/31

WELDING LAB

Name of the lab in-charge : Mr. U.Mohammed Iqbal

Name of the lab Assistant : Mr. K.S.Rajapreyan

Name of the Lab Equipments

1. Spot welding - 1 nos

2. Arc welding equipment - 3 nos

3. Power hack saw - 1 nos

4. MIG welding - 1 nos

5. Gas welding equipment - 1 nos

List of Exercises

A) Arc Welding

1. Preparation of arc welding of Butt joints

2. Preparation of arc welding of Lap joints

3. Preparation of arc welding of T- joints

B) Gas Welding

1.

Demonstration of Gas welding

C) Sheet metal

1. Fabrication of tray

2. Fabrication of cone (or) funnel

3. Different types of joints

Computing facility : NO

Lab Manual : YES

Research oriented :


5/31

MANUFACTURING TECHNOLOGY LAB

Name of the lab in-charge : Mr. J.Shiva Kumar

Name of the lab Assistant : Mr. K.Kandasamy

Mr.V.Karthikeyan


1. Centre lathe - 18 Nos

2. Radial drilling machine

List of Exercises

1. Simple turning

2. Taper turning

3. Drilling


Lab Manual : YES

Research oriented :


6/31

Computer Aided Drafting and Modeling Laboratory

SubjectCode Subject Name

Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2155 Computer Aided Drafting AndModeling Laboratory 0 1 2

List of Experiments / Exercises:1. Study of capabilities of software for Drafting and Modeling Coordinate systems (absolute,

relative, polar, etc.) Creation of simple figures like polygon and general multi-line figures.2. Drawing of a Title Block with necessary text and projection symbol.3. Drawing of curves like parabola, spiral, involute using Bspline or cubic spline.4. Drawing of front view and top view of simple solids like prism, pyramid, cylinder, cone, etc, and

dimensioning.5. Drawing front view, top view and side view of objects from the given pictorial views (eg. V-

block, Base of a mixie, Simple stool, Objects with hole and curves).6. Drawing of a plan of residential building ( Two bed rooms, kitchen, hall, etc.)7. Drawing of a simple steel truss.8. Drawing sectional views of prism, pyramid, cylinder, cone, etc,9. Drawing isometric projection of simple objects.10. Creation of 3-D models of simple objects and obtaining 2-D multi-view drawings from 3-D

model.

Reference Books:1. CAD Lab manual

Text Books: 1. Computer Aided Drafting and Design: Concepts and Applications Donald D.Voisinet


7/31

COMPUTER AIDED DRAFTING AND MODELING LAB

Name of the lab in-charge : Mr. C.K.Dinakarraj

Name of the lab Assistant : Mr. H.Sampath


1. No of computers with accessories - 34 nos

2. Printer (canon) - 2 nos

3. Printer (HP laser jet) - 1 nos

4. Plotter - 1 nos

5. 15 KVA UPS with 3 hrs back up,

100 AH SMF battery - 1 nos

Softwares

1. Auto CAD

CAD Lab List of Exercises

1. Study of capabilities of software for Drafting and Modeling Coordinate systems(absolute, relative, polar, etc.) Creation of simple figures like polygon and generalmulti-line figures.

2. Drawing of a Title Block with necessary text and projection symbol.3. Drawing of curves like parabola, spiral, involute using Bspline or cubic spline.4. Drawing of front view and top view of simple solids like prism, pyramid, cylinder, cone,

etc, and dimensioning.5. Drawing front view, top view and side view of objects from the given pictorial views (eg.

V-block, Base of a mixie, Simple stool, Objects with hole and curves).6. Drawing of a plan of residential building ( Two bed rooms, kitchen, hall, etc.)7. Drawing of a simple steel truss.8. Drawing sectional views of prism, pyramid, cylinder, cone, etc,9. Drawing isometric projection of simple objects.10. Creation of 3-D models of simple objects and obtaining 2-D multi-view drawings from 3-

D model.

Computing facility : YES

Lab Manual : YES

Research oriented :


8/31

Manufacturing Technology Lab I

Subjectcode Subject Name

Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2207 Manufacturing Technology Lab I 0 0 3

List of Experiments / Exercises:1. Two or More Metal Cutting Experiments

(Example: Shear Angle Measurement, Cutting Force Measurement, Cutting TemperatureMeasurement, Tool Wear Measurement, Life Measurement etc.)

2. One or More Exercises in Milling Machines(Example: Milling Polygon Surfaces, Gear milling, Keyway milling, Helical Groove milling etc.)

3. Two or More Exercises in Grinding / Abrasive machining(Example: Surface Grinding, Cylindrical Grinding, Centreless Grinding, Lapping, Honing etc.)

4. Two or More Exercises in Machining Components for Assembly of different fits.(Example: Machining using Lathes, Shapers, Drilling, Milling, Grinding Machines etc.)

5.

One or More Exercises in Capstan or Turret Lathes6. One or More Exercises in Gear Machining(Example: Gear Cutting, Gear Shaping, Gear Hobbing etc.)

7. One or More Exercises in CNC Machines(Example: CNC Programming, CNC Tooling, CNC Machining etc.

LIST OF EQUIPMENT1. Centre Lathes - 15 No (5 Precision Type)2. Turret and Capstan Lathes - 1 No each3. Horizontal Milling Machine - 1 No4. Vertical Milling Machine - 1 No5. Surface Grinding Machine - 1 No6. Tool Dynamometer - 1 No7. Gear Hobbing Machine - 1 No8. CNC Lathe (Trainer or Industrial Type) - 1 No

Reference Books:1. Manufacturing technology lab I Manual.

Text Book:1. Hajra Choudhury, Elements of Workshop Technology, Vol. I and II, Mediab Promotors Pvt

Ltd., Mumbai, 20012. S.Gowri, P.Hariharan, and A.Suresh Babu, Manufacturing Technology 1, Pearson Education ,

2008.


9/31

MANUFACTURING TECHNOLOGY LAB-I



Mr.V.Karthikeyan


1. Centre Lathes - 15 No (5 Precision Type)2. Turret and Capstan Lathes - 1 No each3. Horizontal Milling Machine - 1 No4. Vertical Milling Machine - 1 No5. Surface Grinding Machine - 1 No6. Tool Dynamometer - 1 No7. Gear Hobbing Machine - 1 No8. CNC Lathe (Trainer or Industrial Type) - 1 No

List of Exercises

1.. Two or More Metal Cutting Experiments(Example: Shear Angle Measurement, Cutting Force Measurement, CuttingTemperature Measurement, Tool Wear Measurement, Life Measurement etc.)

2. One or More Exercises in Milling Machines(Example: Milling Polygon Surfaces, Gear milling, Keyway milling, Helical Groovemilling etc.)

3. Two or More Exercises in Grinding / Abrasive machining(Example: Surface Grinding, Cylindrical Grinding, Centreless Grinding, Lapping,Honing etc.)

4. Two or More Exercises in Machining Components for Assembly of different fits.(Example: Machining using Lathes, Shapers, Drilling, Milling, Grinding Machinesetc.)

5. One or More Exercises in Capstan or Turret Lathes6. One or More Exercises in Gear Machining

(Example: Gear Cutting, Gear Shaping, Gear Hobbing etc.)7. One or More Exercises in CNC Machines

(Example: CNC Programming, CNC Tooling, CNC Machining etc.


Lab Manual : YES

Research oriented :


10/31

Manufacturing Technology Lab II


Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2258 Manufacturing Technology Lab II 0 0 3

List of Experiments / Exercises:1. Two or More Measurements in Metal Cutting Experiment (Example: Shear Angle,

Cutting Force, Tool Wear etc.)2. One or More Exercises in Shaper, Slotter, Planner, Drilling, Milling Machines

(Example: Round to Square, Dovetail in shaper, Internal keyway cutting in Slotter,Round to square in Planner, Drilling, reaming and tapping in Drilling machine, GearMilling and Keyway milling in Milling machine.)

3. Two or More Exercises in Grinding / Abrasive machining(Example: Surface Grinding, Cylindrical Grinding.)

4. Two or More Exercises in Assembly of Machined Components for different fits.(Example: Parts machined using Lathes, Shapers, Drilling, Milling, and GrindingMachines etc.)

5. One or More Exercises in Capstan or Turret Lathes6. One or More Exercises in Gear Machining (Example: Gear Milling, Gear Hobbing etc.)

TOTAL: 45 PERIODS

Reference Books:1. Manufacturing Technology Lab II manual.

Text Book:1. Hajra Choudry, Elements of Work Shop Technology Vol. II, Media Promoters. 2002 2. Rao, P.N. Manufacturing Technology, Metal Cutting and Machine Tools, Tata McGraw Hill,

New Delhi, 2003.3. P.C. Sharma, A Text Book of Production Engineering, S. Chand and Co. Ltd, IV edition, 1993. 4. Shrawat N.S. and Narang J.S, CNC Machines, Dhanpat Rai & Co., 2002.


11/31

MANUFACTURING TECHNOLOGY LAB-II



Mr.V.Karthikeyan


1. Centre Lathes - 15 No (5 Precision Type)2. Turret and Capstan Lathes - 1 No each3. Horizontal Milling Machine - 1 No4. Vertical Milling Machine - 1 No5. Surface Grinding Machine - 1 No6. Tool Dynamometer - 1 No7. Gear Hobbing Machine - 1 No

8. CNC Lathe (Trainer or Industrial Type) - 1 NoList of Exercises

1. Two or More Measurements in Metal Cutting Experiment(Example: Shear Angle, Cutting Force, Tool Wear etc.)

2. One or More Exercises in Shaper, Slotter, Planner, Drilling, Milling Machines(Example: Round to Square, Dovetail in shaper, Internal keyway cutting in Slotter,Round to square in Planner, Drilling, reaming and tapping in Drilling machine, GearMilling and Keyway milling in Milling machine.)

3. Two or More Exercises in Grinding / Abrasive machining(Example: Surface Grinding, Cylindrical Grinding.)

4. Two or More Exercises in Assembly of Machined Components for different fits.(Example: Parts machined using Lathes, Shapers, Drilling, Milling, and GrindingMachines etc.)

5. One or More Exercises in Capstan or Turret Lathes6. One or More Exercises in Gear Machining (Example: Gear Milling, Gear Hobbing etc.)


Lab Manual : YES

Research oriented :


12/31

Computer Aided Machine Drawing Laboratory


Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2257 Computer Aided Machine DrawingLaboratory 0 0 3

List of Experiments / Exercises:DRAWING STANDARDSCode of practice for Engineering Drawing, BIS specifications Welding symbols, rivetedjoints,keys, fasteners Reference to hand book for the selection of standardcomponents like bolts, nuts,screws, keys etc.2-D DRAWINGSLimits, Fits Tolerancing of individual dimensions- Specification of Fits- ManualPreparation of production drawings and reading of part and assembly drawings.CAD PRACTICE (USING APPLICATION PACKAGES)Drawing, Editing, Dimensioning, Plotting Commands, Layering Concepts, Hatching,Detailing,Assembly, basic principles of GD&T (geometric dimensioning & tolerancing)ASSEMBLY DRAWING (MANUAL & USING APPLICATION PACKAGES)Manual parts drawing and preparation of assembled views given part details forcomponents followedby practicing the same using CAD packages.Suggested Assemblies:Shaft couplings Plummer block Screw jack- Lathe Tailstock Universal Joint Machine Vice Stuffing box- safety Valves - Non-return valves- Connecting rod Pistonand crank shaft- Multi plateclutch- Preparation of Bill of materials and tolerance datasheet

TOTAL: 45PERIODS

Reference Books:1. Computer Aided Machine Drawing Laboratory manual.

Text Book:

1. BHATT.N.D. and PANCHAL.V.M., Machine Drawing, Charotar Publishing House, 388001, 38th Edition, 2003.

2. P.S.G. Design Data Book 3. Luzadder,Warren.J., and Duff, Jon.M. Fundamentals of Engineering Drawing,Prentice Hall

India Pvt. Ltd., Eastern Economy Edition, Eleventh Edition,


13/31


14/31

Thermal Engineering Laboratory I


Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2306 Thermal Engineering Laboratory - I 0 0 3

Lab Experiment/ Exercise

I.C ENGINE LAB AND FUELS LAB 301. Valve Timing and Port Timing Diagrams.2. Performance Test on 4-stroke Diesel Engine.3. Heat Balance Test on 4-stroke Diesel Engine.4. Morse Test on Multi cylinder Petrol Engine.5. Retardation Test to find Frictional Power of a Diesel Engine.6. Determination of Viscosity Red Wood Viscometer.7. Determination of Flash Point and Fire Point.

STEAM LAB 151. Study of Steam Generators and Turbines.2. Performance and Energy Balance Test on a Steam Generator.3. Performance and Energy Balance Test on Steam Turbine.

TOTAL: 45PERIODS

Reference Books:1. Thermal engineering lab-I manual.

Text Book:1. Sarkar, B.K,Thermal Engineering Tata McGraw -Hill Publishers, 2007


15/31

Thermal Engineering Laboratory I

Name of the lab in-charge : Mr. V.Nadanakumar

Name of the lab Assistant : Mr. J.Selvam


1. Single cylinder diesel engine

2. Two cylinder diesel engine

3. Single cylinder petrol engine

4. Multi cylinder petrol engine

5. Tech-ed engine with data acquisition system6. Computerized variable compression ratio engine

7. Multi cylinder diesel engine

8. Single and two stage air compressor

9. Wind tunnel

10. Air blower

11. Gas analyzer

12. Injection pressure test rig

13. Bomb calorimeter

14. Gas calorimeter

15. Viscometer (Say bolt & redwood)

16. Flash and fire point apparatus (open cup and closed cup apparatus)

17. Cloud and pour point apparatus

Name of the Lab Equipments (STEAM LAB)

1. Bio gasifier2. Vertical axis wind mill

3. Solar heater

4. Single cylinder diesel engine with data acquisition system


16/31

List of Exercises

I.C Engine Lab and Fuels Lab1. Valve Timing and Port Timing Diagrams.

2. Performance Test on 4-stroke Diesel Engine.3. Heat Balance Test on 4-stroke Diesel Engine.4. Morse Test on Multi cylinder Petrol Engine.5. Retardation Test to find Frictional Power of a Diesel Engine.6. Determination of Viscosity Red Wood Viscometer.7. Determination of Flash Point and Fire Point.

Steam Lab1. Study of Steam Generators and Turbines.2. Performance and Energy Balance Test on a Steam Generator.3. Performance and Energy Balance Test on Steam Turbine.


Lab Manual : YES

Research oriented : 1. Data Acquisition system with 4-stroke Diesel

Engine

2. Computerized variable compression ratio engine

3. Wind tunnel


17/31

Dynamics Laboratory


Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2307 Dynamics Laboratory 0 0 3

Lab Experiment/ Exercise1. a) Study of gear parameters.

b) Experimental study of velocity ratios of simple, compound, Epicyclic and differential geartrains.2. a) Kinematics of Four Bar, Slider Crank, Crank Rocker, Double crank, Double rocker, Oscillating

cylinder Mechanisms.b) Kinematics of single and double universal joints.

3. a) Determination of Mass moment of inertia of Fly wheel and Axle system.b) Determination of Mass Moment of Inertia of axisymmetric bodies using Turn Table apparatus.

c) Determination of Mass Moment of Inertia using bifilar suspension and compound pendulum.4. Motorized gyroscope Study of gyroscopic effect and couple.5. Governor - Determination of range sensitivity, effort etc., for Watts, Porter, Proell, and Hartnell

Governors.6. Cams Cam profile drawing, Motion curves and study of jump phenomenon7. a) Single degree of freedom Spring Mass System Determination of natural Frequency and

verification of Laws of springs Damping coefficient determination.b) Multi degree freedom suspension system Determination of influence coefficient.

8. a) Determination of torsional natural frequency of single and Double Rotor systems.- Undampedand Damped Natural frequencies.b) Vibration Absorber Tuned vibration absorber.

9. Vibration of Equivalent Spring mass system undamped and damped vibration.

10. Whirling of shafts Determination of critical speeds of shafts with concentrated loads.11. a). Balancing of rotating masses. (b) Balancing of reciprocating masses.12. a) Transverse vibration of Free-Free beam with and without concentrated masses.

b) Forced Vibration of Cantilever beam Mode shapes and natural frequencies.c) Determination of transmissibility ratio using vibrating table.

13.Students should be familiar with the use of the following device/equipments depending uponavailability.Tachometers Contact and non contactDial gaugeStroboscopeAccelerometers Vibration pickups

Displacement meters.OscilloscopeVibration Shaker

TOTAL: 45 PERIODS Reference Books:

1. Dynamics Lab Manuals

Text Book1. Ambekar A. G., Mechanism and Machine Theory, Prentice Hall of India, New Delhi, 2007.


18/31

DYNAMICS LAB

Name of the lab in-charge : Mr. K.Dhandapani

Name of the lab Assistant : Mr. Sakthibalan


1. Wheel balancing equipment

2. Gyroscope

3. Governor

4. Vibration test rig

List of Exercises

1. a) Study of gear parameters.

b) Experimental study of velocity ratios of simple, compound, Epicyclic and

differential gear trains.

2. a) Kinematics of Four Bar, Slider Crank, Crank Rocker, Double crank, Double rocker,

Oscillating cylinder Mechanisms.

b) Kinematics of single and double universal joints.

3. a) Determination of Mass moment of inertia of Fly wheel and Axle system.

b) Determination of Mass Moment of Inertia of axis symmetric bodies using Turn Table

apparatus.

c) Determination of Mass Moment of Inertia using bifilar suspension and compound

pendulum.

4. Motorized gyroscope Study of gyroscopic effect and couple.

5. Governor - Determination of range sensitivity, effort etc., for Watts, Porter, Proell, and

Hartnell Governors.

6. Cams Cam profile drawing, Motion curves and study of jump phenomenon

7. a) Single degree of freedom Spring Mass System Determination of natural Frequency

and

verification of Laws of springs Damping coefficient determination.

b) Multi degree freedom suspension system Determination of influence coefficient.

8. a) Determination of torsional natural frequency of single and Double Rotor systems.-


19/31

Undamped and Damped Natural frequencies.

b) Vibration Absorber Tuned vibration absorber.

9. Vibration of Equivalent Spring mass system undamped and damped vibration.

10. Whirling of shafts Determination of critical speeds of shafts with concentrated loads.

11. a). Balancing of rotating masses. (b) Balancing of reciprocating masses.

12. a) Transverse vibration of Free-Free beam with and without concentrated masses.

b) Forced Vibration of Cantilever beam Mode shapes and natural frequencies.

c) Determination of transmissibility ratio using vibrating table.


Lab Manual : YES

Research oriented :


20/31

Metrology and measurement laboratory


Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2308 Metrology and Measurement Laboratory 0 0 3

Lab Experiment/ Exercise1. Calibration of Vernier / Micrometer / Dial Gauge2. Checking Dimensions of part using slip gauges3. Measurements of Gear Tooth Dimensions4. Measurement of Angle using sine bar / sine center / tool makers microscope5. Measurement of straightness and flatness6. Measurement of thread parameters7. Setting up of comparators for inspection (Mechanical / Pneumatic / Electrical)8. Measurement of Temperature using Thermocouple / Pyrometer9. Measurement of Displacement10. Measurement of Force

11. Measurement of Torque12. Measurement of Vibration / Shock TOTAL: 45 PERIODS

Reference Books:1. Metrology and measurement lab manual.

Text Book:1. Jain R.K., Engineering Metrology, Khanna Publishers, 20 05


21/31

METROLOGY LAB

Name of the lab in-charge : Mr. S.Pachaiyappan

Name of the lab Assistant : Mr. S.Jayaprakash


1. Micrometer2. Vernier Caliper3. Vernier Height Gauge4. Vernier depth Gauge5. Slip Gauge Set6. Gear Tooth Vernier7. Sine Bar

8. Sine Center9. Bevel Protractor10. Floating Carriage Micrometer11. Profile Projector / Tool Makers Microscope12. Mechanical / Electrical / Pneumatic Comparator13. Autocollimator14. Temperature Measuring Setup15. Tool makers microscope

List of Exercises

1. Calibration of Vernier / Micrometer / Dial Gauge2. Checking Dimensions of part using slip gauges3. Measurements of Gear Tooth Dimensions4. Measurement of Angle using sine bar / sine center / tool makers microscope5. Measurement of straightness and flatness6. Measurement of thread parameters7. Setting up of comparators for inspection (Mechanical / Pneumatic / Electrical)8. Measurement of Temperature using Thermocouple / Pyrometer9. Measurement of Displacement10. Measurement of Force11. Measurement of Torque12. Measurement of Vibration / Shock


Lab Manual : YES

Research oriented :


22/31

CAD/CAM Laboratory


Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2309 CAD/CAM Laboratory 0 0 3

Lab Experiment/ Exercise3D GEOMETRIC MODELINGCreation of 3D Models - Wire Frame, Surface, Solid modeling Techniques Using CAD Packages CSG, B-Rep Approaches in Solid Modeling - Feature Based Modeling Technique Assembly Detailing - Exposure to Industrial Components Application of GD&TSTL FILE GENERATION REVERSE ENGINEERINGManual CNC Part ProgrammingManual CNC Part Programming Using Standard G and M Codes - Tool Path Simulation Exposureto Various Standard Control Systems- Machining simple components by Using CNC machines.COMPUTER AIDED PART PROGRAMMINGCL Data Generation by Using CAM Software Post Process Generation for Different Control System

Machining of Computer Generated Part Program by Using Machining Center and Turning Center.

STUDY OF EXPERIMENTSMulti-axial Machining in CNC Machining Center EDM EDM Wire Cut Rapid Prototyping

TOTAL: 45PERIODS

Reference Books:1. CAD/CAM Lab manuals

Text Book:1. Juvinall R. C., Marshek K.M., Fundamentals of Machine component Design, John Wiley & Sons Third

Edition, 2002.


23/31

CAD/CAM LAB




1.No of computers with accessories - 34 nos



4. Plotter - 1 nos

5. CNC Turning - 1 nos

6. CNC Milling - 1 nos7. 15 KVA UPS with 3 hrs back up,


Softwares

1.Solid works - 30 users

2. Auto CAD

3.

Edge CAM-2011 R

CAD Lab List of Exercises

Creation of 3D Models - Wire Frame, Surface, Solid modeling Techniques Using CADPackages CSG, B-Rep Approaches in Solid Modeling - Feature Based ModelingTechnique Assembly Detailing - Exposure to Industrial Components Applicationof GD&T

CYCLE I : Practice on CNC Lathe

1. Generating a program for facing and turning operation

2. Generating a program for step turning and chamfering operation

3. Generating a program for tapper turning operation

4. Generating a program for thread cutting operation

5. Generating a program for contouring and grooving operation

6. Generating a program for multiple turning operation


24/31

CYCLE II : Practice on CNC Milling

1. Generating a program for profile cutting operation

2. Generating a program for mirroring operation

3. Generating a program for drilling operation


Lab Manual : YES

Research oriented :


25/31

Thermal Engineering Laboratory - II


Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2355 Thermal Engineering Laboratory - II 0 0 3

Lab Experiment/ ExerciseHEAT TRANSFER 30

1. Thermal conductivity measurement by guarded plate method2. Thermal conductivity of pipe insulation using lagged pipe apparatus3. Natural convection heat transfer from a vertical cylinder4. Forced convection inside tube5. Heat transfer from pin-fin (natural & forced convection modes)6. Determination of Stefan-Boltzmann constant7. Determination of emissivity of a grey surface8. Effectiveness of parallel/counter flow heat exchanger

REFRIGERATION AND AIR CONDITIONING 151. Determination of COP of a refrigeration system2. Experiments on air-conditioning system3. Performance test on single/two stage reciprocating air compressor.

TOTAL: 45PERIODS

Reference Books:1. Thermal Engineering Lab-II Manual

Text Book:1. Sarkar, B.K,Thermal Engineering Tata McGraw -Hill Publishers, 20072. Kothandaraman.C.P., Domkundwar.S,Domkundwar. A.V., A course in thermal

engineering,Dhanpat Rai &sons ,Fifth edition, 2002.


26/31

Thermal Engineering Laboratory - II

Name of the lab in-charge : Mr. D.Thamil Selvan

Name of the lab Assistant : Mr. K.Selvam


1. Lagged pipe apparatus

2. Pin fin apparatus

3. Forced convection apparatus

4. Heat pipe apparatus

5. Composite wall apparatus

6. Two slab guarded hot plate

7. Thermal conductivity of metal rod

8. Double pipe heat exchanger

9. Stefan boltzman constant apparatus

10. Thermal conductivity of insulating material

11. Natural convection apparatus

12. Emissivity apparatus

13. Basic water cooling tower14. Air conditioning test rig

15. Refrigeration test rig

List of Exercises

Heat Transfer1. Thermal conductivity measurement by guarded plate method2. Thermal conductivity of pipe insulation using lagged pipe apparatus3. Natural convection heat transfer from a vertical cylinder4. Forced convection inside tube5. Heat transfer from pin-fin (natural & forced convection modes)6. Determination of Stefan-Boltzmann constant7. Determination of emissivity of a grey surface8. Effectiveness of Parallel/counter flow heat exchanger


27/31

Refrigeration and Air Conditioning1. Determination of COP of a refrigeration system2. Experiments on air-conditioning system3. Performance test on single/two stage reciprocating air compressor.


Lab Manual : YES

Research oriented :


28/31

Computer Aided Simulation & Analysis Laboratory


Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2404 Computer Aided Simulation &Analysis Laboratory 0 0 3

Lab Experiment/ ExerciseA. SIMULATION 8

1. Simulation of Air conditioning system with condenser temperature and evaporator2. temperatures as input to get COP using C /MAT Lab.3. Simulation of Hydraulic / Pneumatic cylinder using C / MAT Lab.4. Simulation of cam and follower mechanism using C / MAT Lab.

B. ANALYSIS (SIMPLE TREATMENT ONLY) 371. Stress analysis of a plate with a circular hole.2. Stress analysis of rectangular L bracket3. Stress analysis of an axi-symmetric component4. Stress analysis of beams (Cantilever, Simply supported, Fixed ends)5. Mode frequency analysis of a 2 D component6. Mode frequency analysis of beams (Cantilever, Simply supported, Fixed ends)7. Harmonic analysis of a 2D component8. Thermal stress analysis of a 2D component9. Conductive heat transfer analysis of a 2D component10. Convective heat transfer analysis of a 2D component

TOTAL: 45 PERIODSReference Books:

1. Computer Aided Simulation & Analysis Lab manuals

Text Book:1. Juvinall R. C., Marshek K.M., Fundamentals of Machine component Design, John Wiley & Sons Third

Edition, 2002.2. P.Seshu, Text Book of Finite Element Analysis, Prentice -Hall of India Pvt. Ltd., New Delhi,

2007. ISBN-978-203-2315-5


29/31

Computer Aided Simulation & Analysis Laboratory



Name of the Lab Equipments 1.No of computers with accessories - 34 nos



4. Plotter - 1 nos

5. CNC Turning - 1 nos

6. CNC Milling - 1 nos

7. 15 KVA UPS with 3 hrs back up,


Softwares

1.ANSYS

List of Exercises

A. SIMULATION 81.Simulation of Air conditioning system with condenser temperature and evaporator2. temperatures as input to get COP using C /MAT Lab.

3.

Simulation of Hydraulic / Pneumatic cylinder using C / MAT Lab.4. Simulation of cam and follower mechanism using C / MAT Lab.B. ANALYSIS (SIMPLE TREATMENT ONLY) 37

1. Stress analysis of a plate with a circular hole.2. Stress analysis of rectangular L bracket3. Stress analysis of an axi-symmetric component4. Stress analysis of beams (Cantilever, Simply supported, Fixed ends)5. Mode frequency analysis of a 2 D component6. Mode frequency analysis of beams (Cantilever, Simply supported, Fixed ends)7. Harmonic analysis of a 2D component8. Thermal stress analysis of a 2D component9. Conductive heat transfer analysis of a 2D component10. Convective heat transfer analysis of a 2D component


Lab Manual : YES

Research oriented :


30/31

Mechatronics Laboratory


Lectures(Periods)

Tutorial(Periods)

Practical(Periods)

ME 2405 Mechatronics Laboratory 0 0 3

Lab Experiment/ ExerciseLIST OF EXPERIMENTS

1. Design and testing of fluid power circuits to control2. velocity (ii) direction and (iii) force of single and double acting actuators3. Design of circuits with logic sequence using Electro pneumatic trainer kits.4. Simulation of basic Hydraulic, Pneumatic and Electric circuits using software5. Circuits with multiple cylinder sequences in Electro pneumatic using PLC6. Speed Control of AC & DC drives7. Servo controller interfacing for DC motor8. PID controller interfacing9. Stepper motor interfacing with 8051 Micro controller10. full step resolution (ii) half step resolution11. Modeling and analysis of basic electrical, hydraulic and pneumatic systems12. using LAB VIEW13. Computerized data logging system with control for process variables like14. pressure flow and temperature

TOTAL: 45 PERIODS

Reference Books:1. Mechatronics Lab Manual

Text Book:1. Bolton,W, Mechatronics , Pearson education, second edition, fifth Indian Reprint, 2003


31/31

MECHATRONICS LAB

Name of the lab in-charge : Mr. N.Senthil Kumar

Name of the lab Assistant : Mr. A.Vignesh


1. No of computers with its accessories - 15 Nos.

2. Printer (HP laser jet) - 1 Nos.

Softwares

1. Lab view - 50 users

2. Fluid SIM - 10 users

(Hydro SIM-5, pneumo SIM-5)

List of Exercises

1. Controlling the speed of the double acting cylinder by using Meter in and Meter out.2. Automatic operation of double acting cylinder in single cycle using limit switches.3. Controlling the operation of double acting cylinder using Memory valves.4. Controlling the operation of single acting cylinder using single solenoid valve.5. Operation of double acting cylinder using solenoid valve use separate manual

controls for Forward and Reverse stroke.6. Multi cycle operation of double acting cylinder using electro pneumatic kit.7. Automatic operation of double acting cylinder using single cycle using limit switch

and Memory valve.8. Control of DC Motor with PID controller.9. Speed control of AC servomotor by using PLC controller.10. Connection of stepper motor with microcontroller to obtain forward and reverse

motion.11. Connection of stepper motor with microcontroller for required angle.12. Speed controller of AC servomotor by using PLC controller with counter, timer.

13. Conversion of inch to millimeter and farebeat to Celsius using lab view.


Lab Manual : YES

Research oriented :

specific labs

Documents