stolle e06 conversion system...speeds up to an unprecedented 850 spm. stolle has incorporated many...
TRANSCRIPT
Copyright 2021 Stolle Machinery Company, All Rights Reserved
C o n n e c t i n g
T E C H N O L O G Y L E A D E R S H I P I N C A N & E N D M A K I N G
Stolle E06 Conversion System
Stolle once again raises the bar on the high volume production of easy open ends for beverage cans with the new EO6 Conversion System. With 6 lanes of conversion and tab tooling, this high speed machine can produce up to 5100 ends per minute – a 70% increase in volume over a 4-lane Tetrad system. In an end module with a 24-out shell system and 6 liners, this increased throughput will allow three Tetrads to be replaced with two EO6 machines while increasing end production from 9000 EPM up to 10,200 EPM.
The E06 system features a completely new Minster ECH-140 press that’s specifically designed for high speed EOE production with speeds up to an unprecedented 850 SPM. Stolle has incorporated many of the tooling and transfer system features we have perfected over many years of conversion system leadership, and has added a number of new technology features that take the EO6 system to new heights of productivity and efficiency. Three transfer belts with two lanes each carry ends through three 2-out lane dies. The 6-out tab die has several improved design features and can produce the latest generation X3 metal-saving tab design.
Stolle E06 Conversion System Features:• New design 140 ton Minster ECH-140 press - Speeds up to 850 SPM - Shorter 1.25” stroke for more efficient operation - AIM (Adjust In Motion) – ram shutheight can be adjusted while press is in operation which reduces end spoilage - Low deflection slide increases tooling precision - 4” ram quick lift for tooling access (higher than 2½” on Tetrad)
• Reliable Stolle end transfer system - 3 non-metallic transfer belts with 2 lanes each - 2.5” progression accommodates 200 and 202 diameter ends - Servo-driven downstacker - Swing-away feed apron provides easy access to tooling - Sencon or Prime Controls end testers mount on unload assembly• Improved design lane dies - Thicker lower die shoe - New idle bar at stake station retains end in belts - Composite material lift gate with longer lift springs - Compact design vacuum boxes for better tooling access
• Improved design 6-out tab die - 3.4% better metal efficiency ($.04/1000 metal savings) - Additional lift springs provide better lift and control of tab strip - Mechanical push feeder with re-designed tab feed linkage for improved life and precision operation
• Cast frames on all feed assemblies - Frames designed for vibration absorption - Welded joints are eliminated for increased long term reliability
• Oil cooling for both transfer belt and tab stock indexers - Reduced maintenance and increased service life
Left: Discharge side showing three 2-out lane transfer belts and end leak testersBelow left: End infeed assembly with swing-away feed apron and downstacker lift cylinderBelow right: Configuration of three 2-out lane dies and 6-out tab die
Stolle Machinery Company6949 South Potomac Street, Centennial, CO 80112 USA
303.708.9044 ~ Fax [email protected] ~ www.stollemachinery.com
S M A R T & T E C H N O L O G Y Stolle E06 Conversion System
SpecificationsPress Size 140 ton single action
Number of Lanes 6
Max. Strokes per Minute 850
Output (maximum EPM) 5100
End Diameter Range 113 – 202
Overall Dimensions - Front-Back 120” (3.048 meters)
Height (with isolation mounts) 176” (4.4704 meters)
Weight (approximate) 120,000 lbs (54431 kg)
Floor space (estimated) 12’ W x 13” L = 156 sq. ft. (14.5 sq. meter) (press & electrical panel; does not include tab stock uncoiler or other equipment)
Air Supply Requirements 88 - 150 PSI – 25 SCFM @ 100 PSI
Water Supply Requirements TBD by Minster
Electrical Power Requirements 380–460 volts – 3 phase – 50/60 Hz (per customer’s requirement), 250 Amp service
Total Connected HP 123 HP
Press Drive Motor 75 HP AC
Press Hydraulic Motor 5 HP AC
Press Lube Motor 7.5 HP AC
Vacuum Blower (1) 30 HP AC
Stake Vacuum Pump (1) 7.5 HP AC
Indexer Chiller 2 HP AC
Ram Quick Lift Height 4”
Ram Adjust in Motion Yes
Greg Williams – Primary Product Contact+1 937-497-5441 • [email protected]
Jason Davidson – Secondary Product Contact+1 937-497-5432 • [email protected]
Roger Naseman – Spare Parts +1 937-497-5477 • [email protected]
Craig McEldowney – Field Service+1 937-497-5406 • [email protected]